Professional Documents
Culture Documents
Ÿ Latest state-of- the-art current mode PWM controller and MOSFET based design.
Ÿ LED indications for AC OK, DC OK, OVP (over voltage protection) and Low Battery.
Ÿ Power supply unit & electronics switch over unit are in the same housing.
Ÿ AC mains fail, SMPS fail & Pre low battery cut off indication floating
Ÿ contact for remote signalling.
Ÿ Provision for two 12V 7AH maintenance free battery.
Ÿ Soft start circuit to limit the AC inrush current.
Ÿ Reliable even at high ambient temperature.
Ÿ BIS Approved.
SPECIFICATIONS
Input voltage 180-265VAC
Frequency 45-60Hz
Inrush current <75A
AC current consump on 4A
Input Indica on AC OK- Yellow LED
Characteris cs Input protec on 4A Subminiature fuse (Time-Lag type)
Transient surge protec on Yes (varistor)
Filter EMI/RFI
Buffer me >20msec at full load
Efficiency >80%
Nominal voltage 24VDC
Voltage adj. range 24-30VDC
Nominal current 10A (including ba ery charging current)
Ba ery charging current Up to 2A
Maximum output power 300W
Line regula on < +/- 0.5%
Load regula on < +/- 0.5%
Ripple and noise < +/- 1% P-P
Output
Low ba ery cut off Yes, at 22VDC +/-1V
Characteris cs
a) AC mains fail
b) SMPS fail
Signaling (op onal) c) Pre low ba ery cut off
* Relay Contact (Max. 240VAC/60VDC-500mA)
Indica ons DC OK- Green LED, OVP- Red LED, LOW BAT-Red LED
Connec on in parallel Yes, with diode ORing
Over voltage protec on Yes, normally works within 31-36VDC
Over load protec on Yes, normally works within 102-120% of rated
nominal current
Short circuit protec on Yes (short-term)
SPECIFICATIONS
INSTALLATION POSITION
2 4 5 .0
1 1 0 .0
3 8 2 .0
1 6 .0
2 1 8 .0 2 4 2 .0
8 .0
8 .0 3 6 3 .0 8 .0
3 7 9 .0
CONNECTION DIAGRAM
SSM24BIS10-SMPS-BCBKEY
SSM24BIS10-SMPS-BC
E N L NO C NC NO C NC NO C NC -V +V -B +B
230VAC @50Hz PFC FOR SMPS PFC FOR AC PFC FOR PRE LOW 24VDC @08A
INPUT FAIL MAINS FAIL BATTERY CUT OFF OUTPUT TO LOAD Switch
(OPTIONAL) (OPTIONAL) (OPTIONAL)
- 24V +
Ba ery
Module
100 100
80 80
Load (%)
Load (%)
60 60
40 40
20 20
NOTE
1) The license number assigned for BIS approval is R-71014273.
2) All these parameters are specified at 230VAC@50Hz input voltage and ambient temperature (+25°C).
3) Two 12V DC rechargeable ba eries of same capacity must be connected in series for 24VDC ba ery module.
4) For con nuous improvement, specifica ons subject to change without prior in ma on.
5) For AC Mains Fail Floa ng Contact, please men on (A) in front of product code while placing the order.
6) For SMPS Fail Floa ng Contact, please men on (S) in front of product code while placing the order.
7) For Pre Low Ba ery Cut Off Floa ng Contact, please men on (P) in front of product code while placing the order.
8) Recommended to connect the ba ery module via a switch for remote shutdown.
9) Please do not connect ba ery below 23VDC.
VOCAL
for
LOCAL
An ISO 9001:2015 Cer fied Company
Make in India
+91 7104 242577 l +91 97655 57591-99
sales@micropower-india.com I www.micropower-india.com
Page 3 of 3 SSM24BIS10-SMPS-BCBKEY Dt:17/03/21 V1