Professional Documents
Culture Documents
INTERNATIONAL ISO
STANDARD 887
Second edition
2000-06-15
Reference number
ISO 887:2000(E)
ISO 887:2000
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (lEG) on all matters of electrotechnical standardization.
Intemational Standards are drafted in accordance with the rules given in the ISOIIEC
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an Standard requires approval by at 75 % of the member bodies a vote.
Attention is drawn to the possibility that some of the elements of International Standard may be the of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 887 was prepared by Technical Committee ISOlTe 2, Fasteners.
This second edition cancels and reDlaCE�S the first edition (ISO 887:1 983), which has been technically revised.
iii
EN ISO 887:2000
Plain washers for metric bolts, screws and nuts for general
purposes - General plan
1 Scope
This International Standard specifies the full range of the nominal dimensions of product-grade-A and plain
washers for general-purpose bolts, screws and nuts of nominal thread diameters ranging from 1 mm to 150 mm
inclusive.
This International Standard is not applicable to washers for screw and washer assemblies in relation to hole
diameters and thicknesses.
2 Normative reference
following normative document contains provisions which. through reference in this text, constitute provisions of
this International Standard. For dated subsequent amendments to, or revisions of, any of these
publications do not However, parties to based on this International Standard are encouraged to
mv,estlloalte the of applying the most recent edition of the normative document indicated below. For
,., .. "f"'... references, the latest edition of the normative document referred to applies. Members of ISO and lEe
3 Clearance holes
clearance hole d1 for washers Figure 1) be chosen in """",.,,1"1:"'''''-0 with those specified in
ISO 273, as follows:
fine series for washers of product A and with a nominal thickness of less than 6 mm, i.e. for nominal
sizes < 39 mm;
medium series for washers of product grade A with a nominal thickness equal to or greater than 6 mm, I.e. for
nominal sizes", 39 mm and for washers of product C.
NOTE The tolerances for clearance holes given in ISO 273 for information are not applicable to plain washers of product
grades A and C; see clause 6.
1
ISO 887:2000
4 Outside diameters
The outside diameters d2 for washers 1) shall be chosen from the values in Table 1.
Table 1 - Dimensions d2
Values in millimetres
5 Thicknesses
Table 2 - Dimensions h
Values in millimetres
0,3 1 2 4 8 14
0,5 1,2 2,5 5 10 16
0,8 1,6 3 6 12 18
•
6 Tolerances
2
EN ISO 887:2000
The preferred combinations of nominal dimensions d1, d2 and h for plain washers of product grades A and C (see
Figure 1) are given in Table 3. The washers are divided into four series: small, large and extra These
series are related to the size of the outside diameter d2.
Figure 1 - Dimensions
Table 3 - Nominal of plain washers
Dimensions en millimetres
Nominal
Series
size
Small Normal Extra
Product grade A Prod A Product grade C Product grade A Product grade C Product grade C
(Thread � � �
size, d)
d1 d, d2 "- (II d2 h dl d2 II ci2 II � d1 d2 II
11,21 1,3
o
1,4
x 1,2 7 2,2,,411 54,5 I 0,0,,33 5 0,3
2 12,2 x 2.2,2,427 22,.6 76 00,,551 X 2,7 68 I 0 5 2,2,6 0,5
2,2
2,5
3,3,27 0,5 3,,941 8 I 0,5 xX 33,,72 119 00,,,88 I XX 33,94 0,0,58 X
3
1618 4 XXX12217,20,51756602 55 X
44
XX
3
31 6056 45 XX XX
44 26
X 36 1 115 8
27
30
33 34 60 5 X 36 33 33
36 37 60 5 X 37 66 5 X X 39 66 5 X 39 110 8 X 39 110 8 X 39 125 8 X
39 42 72 6 X X 42 72 6 X 42 120 8 42 120 8 42 140 10
42 45 78 8 X X 45 78 8 X 45 125 10 45 125 10
45 48 85 8 X X 48 85 8 X 48 135 10 48 135 10
48 52 92 8 X X 52 92 8 X 52 1 45 10 52 145 10
52 56 98 8 X X 56 98 8 X 56 160 10 56 160 10
56 62 105 10 X X 62 105 10 X
60 66 110 10 X X 66 110 10 X
64 70 115 10 X X 70 115 10 X
68 74 120 10 74 120 10
72 78 125 10 78 125 10
76 82 135 10 82 135 10
80 86 140 12 86 140 12
85 91 145 12 91 1 45 12
90 96 160 12 96 160 12
NOTe The crosses indicate washers specified in the corresponding Inlemi'lti 'Jr'1�! Standiards.
""'"
rJ'j
o
(,11
EN ISO 887:2000
Annex A
(informative)
Guidance on the use of plain washers with bolts, screws and nuts
An overview of suitable combinations of washers and bolts, screws or nuts in respect of property (hardness)
classes and product is given in A.1
More detailed information, including washer series and bolt or screw head is in the scopes of the
r"",""..,,'tl\t" plain-washer product standards.
Table A.1
8.8 no yes
Bolts, screws class
9.B,10.9 no no yes
12.9 no no no
Bibliography
v,,-,.;p"""/VV, Tolerances for fasteners - Part 3: Plain washers for screws and nuts --
[3] ISO 7090:2000, Plain washers, chamfered - Normal series - Product grade A.
[6] ISO 7093-1 :2000, Plain washers - series -- Part 1: Product grade A.
7
ISO 887:2000
Annex ZA
Normative references to international pUIIlIiI:atIOI1IS
with their relevant publications
Publication
ISO 273 1979 Fasteners· Clearance holes for bolts and screws EN 20273 1991