Professional Documents
Culture Documents
Resolution: 1 bottom of the display. The top of the display will show
tco Temperature Compensation Coefficient value the current reading. “HOLD” will no longer
Range: 0.00 to 19.99 ppt (parts per thousand) the value that the meter was calibrated to for the
(see the “Setting Temperature Compensation appear on the display.
Resolution: 0.1 range of 0 to 1999 µS. (If no user calibration has been
Coefficient” section).
TDS Factor: 0.40 to 1.00, 0.01 increments performed, “- - - ” will appear.)
tds TDS Factor value (see the “Setting TDS Ç button, P4.2 will appear at the AUTOMATIC SHUTOFF (Disable)
Automatic Temperature Compensation— 5. Press the MODE
Factor” section). If no button has been pressed for twenty (20) minutes,
Range: 32.0 to 122.0 °F / 0.0 to 50.0 °C bottom of the display. The top of the display will
ran Range display mode (see the “Range Mode the Automatic Shutoff feature will turn the meter off to
Normalization: 20 °C or 25 °C (user selectable) show the value that the meter was calibrated to for the
Selection” section). preserve battery life.
Coefficient: 0.0 to 4.0% per °C, 0.1 increments range of 0 to 19.99 mS. (If no user calibration has
Temperature Measurement— been performed, “- - - ” will appear.) To disable the Automatic Shutoff feature:
CONDUCTIVITY CALIBRATION È
Range: 32.0 to 122.0 °F / 0.0 to 50.0 °C 6. Press the ON/OFF button, P4.0 will appear at the 1. With the meter turned off, press and hold the HLD/CAL
One calibration point may be entered for each of the
SET
Resolution: 0.1° bottom of the display. button, then press and hold the ON/OFF
SET button until
measurement ranges (0 to 1999 µS and 0.00 to 19.99 mS).
7. Press and hold the ON/OFFSET button for approximately “n ” appears on the display.
OPERATION To insure accuracy: three (3) seconds, the meter will return to the È and ON/OFF
2. Release the HLD/CAL SET buttons. The meter
This section contains basic operating instructions, to –Always use Traceable® Conductivity Standards measurement display. will power on and the Automatic Shutoff feature will
insure accurate results and for more advanced functions, –Select a Traceable® Conductivity Standard with a value be disabled.
refer to the additional sections that follow. as close as possible to the value of the unknown sample. SELECTING °F OR °C The Automatic Shutoff feature is automatically enabled
–If possible, the Traceable® Conductivity Standard and 1. Turn the meter on by pressing the ON/OFF button.
1. Remove the protective cover from the probe head.
SET
when the meter is powered off and turned back on.
unknown sample should be at the same temperature. 2. Press and hold the ON/OFF button for approximately
2. Turn the meter on by pressing the ON/OFF button.
SET
measure will flash on the display. fluids increase in conductivity as temperature increases.
◄ 5. To insure Automatic Temperature Compensation, 1. Remove the protective cover from the probe head. Ç button, the temperature reading will
4. Press the MODE
immerse the probe head and temperature sensor Depending on the value selected here, Automatic
2. Turn the meter on by pressing the ON/OFF
SET button. switch to the opposite unit of measure. If the meter
completely. For accurate Automatic Temperature Temperature Compensation (ATC) will automatically
3. Place the probe head into the Traceable® Conductivity had been displaying °F, it will now display °C, and
Compensation, the temperature sensor must reach make corrections to the reading and display a value as
Standard. vice-versa. Each press of the MODEÇ button will switch
equilibrium with the liquid being measured, this could if the sample was 25 °C or 20 °C, no matter what the
4. To insure Automatic Temperature Compensation, the display to the opposite unit of measure.
take several minutes. actual sample temperature is. The international standard
immerse the probe head and temperature sensor 5. With the desired unit of measure appearing, press the
6. Insure that there is adequate movement of the liquid temperature normalization value is 25 °C.
completely. For accurate Automatic Temperature ON/OFF
button three (3) times, P1.0 will appear at the
around the tip of the probe head (0.2 - 0.3 meters per
SET
Compensation, the temperature sensor must reach bottom of the display. The following procedure is used to change the
second minimum). This can be achieved by stirring the equilibrium with the liquid being measured, this could temperature normalization value from 25 °C to 20 °C, or
6. Press and hold the ON/OFF button for approximately
meter in the liquid.
SET
take several minutes. three (3) seconds, the meter will return to the from 20 °C to 25 °C.
The meter will automatically select the range that is the 5. Insure that there is adequate movement of the liquid measurement display. 1. Turn the meter on by pressing the ON/OFF
SET button.
most appropriate for the value being measured. For around the tip of the probe head (0.2 - 0.3 meters per
The unit of measure selected will be the default unit of 2. Press and hold the ON/OFF
SET button for approximately
example, when measuring a 500 µS solution, the meter second minimum). This can be achieved by stirring the
measure until changed. three (3) seconds, P1.0 will appear at the bottom of
will select the µS range and display 500 µS as opposed meter in the liquid.
È button for approximately the display.
to displaying 0.50 mS. To manually select the range, 6. Press and hold the HLD/CAL
RANGE MODE SELECTION 3. Press the ON/OFF
SET button two (2) times, the temperature
Ç button for approximately three
press and hold the MODE three (3) seconds, CAL will appear at the top of the
The meter will automatically select the range that is the normalization value will flash on the display.
(3) seconds, if the value being measured is able to be display and the conductivity measurement will flash. Ç button, the temperature normalization
Ç and/or HLD/CAL
È buttons to adjust the most appropriate for the value being measured. For 4. Press the MODE
displayed in the alternate range, the meter will switch 7. Press the MODE Ç button will
example, when measuring a 500 µS solution, the meter value will change. Each press of the MODE
ranges (see the “Range Mode Selection” section). display to the know value of the Traceable® Conductivity
will select the µS range and display 500 µS as opposed switch between 25.0 °C (77.0 °F) and 20.0°C (68.0°F).
Standard. The meter may only be adjusted by ±30%
7. Take the desired measurements. to displaying 0.50 mS. 5. With the desired temperature normalization value
of the detected value.
8. Press the ON/OFF button to turn the meter off. appearing, press the ON/OFF
SET button two (2) times,
8. With the the know value of the Traceable® Conductivity To manually select the display range, press and hold
SET
To preserve battery life, always turn the meter off when Ç button for approximately three (3) seconds, if P1.0 will appear at the bottom of the display.
Standard appearing and CAL no longer flashing, the MODE
not in use. 6. Press and hold the ON/OFF
SET button for approximately
press the ON/OFF button, the meter will return to the the value being measured is able to be displayed in the three (3) seconds, the meter will return to the
SET
9. Rinse the probe head with distilled/deionized water and
measurement display. alternate range, the meter will switch ranges.
replace the protective cover. Always replace the measurement display.
protective cover to prevent damage to the probe head. Ç button for pressed and held, the
Each time the MODE The temperature normalization value selected will be the
range mode will cycle through the available modes:
If no button is pressed for twenty (20) minutes, the meter default value until changed.
ATO Automatic range selection
will turn off automatically to preserve battery life (see the
1 0 to 1999 µS / 0 to 1999 ppm
“Automatic Shutoff” section).
2 0.00 to 19.99 mS / 0.00 to 19.99 ppt
SETTING TEMPERATURE COMPENSATION SETTING TDS FACTOR DISPLAY MESSAGES
COEFFICIENT The Total Dissolved Solids (TDS) value that appears on Upper Display Messages:
Conductivity is greatly influenced by temperature. Most the display is a result of the conductivity measurement of --- Indicates that the meter is in the manual
fluids increase in conductivity as temperature increases. the fluid being multiplied by the TDS factor. range selection mode and the value being
The value set here will determine how much the measured is higher than 1999 µS or 1999 ppm.
Automatic Temperature Compensation (ATC) feature will
Every liquid will have a different TDS factor. An
E03 Indicates that the value of the solution being
TRACEABLE®
approximation of the dissolved solids for a fresh-water
adjust the value for every 1 °C in order to automatically source can be arrived at by using a TDS factor of 0.66. If measured exceeds the measurement range of CONDUCTIVITY/
make corrections to the reading and display a value as the unit. TOTAL DISSOLVED
the TDS factor of the solution being measured is known,
if the sample was 25 °C or 20 °C (see the “Selecting E04 Indicates that the value of the solution being
Temperature Normalization Value” section), no matter
that value should be entered in order to obtain the most
measured exceeds the measurement range of
SOLIDS
accurate results. METER
what the actual sample temperature is. the unit based on a temperature measurement
The following procedure is used to set the TDS factor. error (see the “Lower Display Messages” section). INSTRUCTIONS
Although every fluid will have a different temperature
1. Turn the meter on by pressing the ON/OFF button. Lower Display Messages:
coefficient, a temperature compensation coefficient of SET
2. Press and hold the ON/OFF button for approximately E01 Indicates that the temperature sensor is damaged.
2.0% is a generally accepted standard compensation SET
three (3) seconds, P1.0 will appear at the bottom of E02 Indicates that the temperature of the solution
value. If the temperature coefficient of the solution being
the display. being measured is below the measurement
measured is known, that value should be entered in
Ç button, P2.0 will appear at the
3. Press the MODE range of the unit.
order to obtain the most accurate results. To take non-
bottom of the display. E03 Indicates that the temperature of the solution
temperature compensated measurements, a temperature
4. Press the ON/OFF button, the TDS factor value will flash being measured is above the measurement
compensation coefficient of 0.0% should be entered. SET
P1.0 will appear at the bottom of the display. the batteries need replacement. The battery cover is
Resetting the meter will clear all calibration data and located at the top of the unit. Unscrew the battery cover
6. Press and hold the ON/OFF button for approximately reset the user selectable values to the factory defaults.
SET
three (3) seconds, the meter will return to the by turning it counter-clockwise. Remove the exhausted
Factory defaults are as follows: batteries and replace them with four (4) new #357/LR44
measurement display. Temperature display: °C size silver oxide batteries. Make certain to insert the
The temperature coefficient value selected will be the Normalization Temperature: 25 °C new batteries with the proper polarity as indicated by the
default value until changed. Temperature Coefficient: 2.1% “+” and “–” symbols in the battery compartment. The
TDS Factor: 0.50 “+” side of the silver oxide battery is the flat side with
The following procedure is used to reset the meter to the the engraving. Replace the battery cover and tighten
factory default values. securely.
1. Turn the meter on by pressing the ON/OFF button.
WARRANTY, SERVICE, OR RECALIBRATION
SET