Professional Documents
Culture Documents
D90 Repair Guidance For DTC Code 20170908
D90 Repair Guidance For DTC Code 20170908
5HSDLUJXLGDQFHIRU'IDXOWFRGH
D90
2017 Year
目 录 Contents
BCM 故障码维修指导 Repair guidance for BCM fault code ................................ 2-1
BCM 故障码及故障类型描述汇总 ............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
FICM 故障码维修指导 Repair guidance for FICM fault code .............................. 3-1
FICM 故障码及故障类型描述汇总............................................................................................. 3-1
1
目 录 Contents
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code......... 4-1
Colour radio 故障码及故障类型描述汇总.................................................................................. 4-1
Description on the fault code and failure type .......................................................................... 4-1
SRS 故障码维修指导 Repair guidance for SRS fault code ................................. 2-1
SRS 故障码及故障类型描述汇总 .............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
TBOX 故障码维修指导 Repair guidance for TBOX fault code ............................ 2-1
TBOX 故障码及故障类型描述汇总............................................................................................ 2-1
2
目 录 Contents
TCCU 故障码维修指导 Repair guidance for TCCU fault code ............................ 2-1
TCCU 故障码及故障类型描述汇总 ........................................................................................... 2-1
Description on the fault code and failure type .......................................................................... 2-1
AFS 故障码维修指导 Repair guidance for AFS fault code .................................. 2-1
AFS 故障码及故障类型描述汇总 .............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
EDL 故障码维修指导 Repair guidance for EDL fault code .................................. 2-1
EDL 故障码及故障类型描述汇总 .............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
IPK 故障码维修指导 Repair guidance for IPK fault code .................................... 2-1
IPK 故障码及故障类型描述汇总................................................................................................ 2-1
Description on the fault code and failure type .......................................................................... 2-1
DCDC 故障码维修指导 Repair guidance for DCDC fault code ........................... 2-1
DCDC 故障码及故障类型描述汇总 ........................................................................................... 2-1
3
目 录 Contents
DSM 故障码维修指导 Repair guidance for DSM fault code ................................ 2-1
DSM 故障码及故障类型描述汇总 ............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
EMS 故障码维修指导 Repair guidance for EMS fault code ................................ 3-1
EMS 故障码及故障类型描述汇总.............................................................................................. 3-1
Description on the fault code and failure type .......................................................................... 3-1
HVAC 故障码维修指导 Repair guidance for HVAC fault code ............................ 2-1
HVAC 故障码及故障类型描述汇总 ........................................................................................... 2-1
Description on the fault code and failure type .......................................................................... 2-1
LDW 故障码维修指导 Repair guidance for LDW fault code ................................ 2-1
LDW 故障码及故障类型描述汇总 ............................................................................................. 2-1
4
目 录 Contents
PTG 故障码维修指导 Repair guidance for PTG fault code ................................. 2-1
PTG 故障码及故障类型描述汇总 .............................................................................................. 2-1
Description on the fault code and failure type .......................................................................... 2-1
TCU 故障码维修指导 Repair guidance for TCU fault code ................................. 3-1
TCU 故障码及故障类型描述汇总 .............................................................................................. 3-1
Description on the fault code and failure type .......................................................................... 3-1
TPMS 故障码维修指导 Repair guidance for TPMS fault code ............................ 4-1
TPMS 故障码及故障类型描述汇总 ........................................................................................... 4-1
Description on the fault code and failure type .......................................................................... 4-1
5
目 录 Contents
6
控制器名称 Controller name
控制器名称 Controller name
控制器名称代码
Controller name cade
控制器
控制器名称 (中文) 控制器名称 (英文)
名称代码
DSM 座椅记忆模块
1-1
控制器名称 Controller name
1-2
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
ABS-ESP 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障码
故障码描述 DTC Description
DTC
2-2
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障码
故障码描述 DTC Description
DTC
U0513-08 从惯性传感器收到无效 CAN 消息 Invalid CAN message Received from MMx sensor
2-3
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
ABS-ESP 故障详解
DTC Valve fault, USV1(ESC Only) DTC Valve fault, USV2(ESC Only)
Description Description
Failure * The internal Valve-Driver-ASIC register Failure * The internal Valve-Driver-ASIC register
criteria is not matching with the current actuation criteria is not matching with the current actuation
during the ValveActuationRegisterTest during the ValveActuationRegisterTest
(detect 15ms) (detect 15ms)
* Shortcut between valves or defective * Shortcut between valves or defective
coil (detect 15ms) coil (detect 15ms)
* Valve resistor of USV 1 is out of range * Valve resistor of USV 2 is out of range
(detect 15ms) (detect 15ms)
* USV 1 defect due to valve driver * USV 2 defect due to valve driver
feedback(detect 30ms) feedback(detect 30ms)
Healing USV 1 valve work properly Healing USV 2 valve work properly
condition condition
2-4
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-5
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-6
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-7
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-8
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-9
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-10
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-11
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-12
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-13
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-14
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-15
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-16
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-17
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-18
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
Failure * Pressure Sensor Master Cylinder 1 Failure Steering Wheel Sensor Signal
criteria Line Failure criteria Implausible
* The offset value of the master cylinder
pressure sensor Ps MC1 is out of 故障治愈条 修复故障,重新点火
specification. 件
* Pressure sensor sensitivity is out of Healing Repair the error, then IG on again
specification condition
* Pressure sensor voltage signal out of
range, voltage > 3.29V or voltage <
0.13V
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-19
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-20
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-21
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-22
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-23
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-24
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-25
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-26
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-27
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-28
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-29
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-30
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-31
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-32
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
Failure Any message below time out Failure Corrupted data or invalide signal
criteria -GW_TCCU_328h criteria received from the any of below
messages
故障治愈条 修复故障,重新点火 -GW_TCCU_328h
件
故障治愈条 修复故障,重新点火
Healing Repair the error, then IG on again 件
condition
Healing Repair the error, then IG on again
condition
2-33
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-34
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
可能的影响 - 可能的影响 -
Possible - Possible -
Symptom Symptom
Failure Any message below time out Failure Any message below time out
criteria -EPB_245h criteria -EPS_335h
2-35
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-36
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-37
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition
2-38
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
可能的影响 - 可能的影响 -
Possible - Possible -
Symptom Symptom
Failure Corrupted CAN data or invalide signal Failure Corrupted CAN data or invalide signal
criteria received from the any of below criteria received from the any of below
messages messages
-EPB_245h -EPS_335h
2-39
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-40
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
Failure Corrupted CAN data or invalide signal Failure Corrupted CAN data or invalide signal
criteria received from the any of below criteria received from the any of below
messages messages
-SAS_266h -GW_HVAC_510h
-GW_SRS_355h
故障治愈条 修复故障,重新点火
件 故障治愈条 修复故障,重新点火
件
Healing Repair the error, then IG on again
condition Healing Repair the error, then IG on again
condition
2-41
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-42
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-43
ABS-ESP 故障码维修指导 Repair guidance for ABS-ESP fault code
2-44
APA 故障码维修指导 Repair guidance for APA fault code
APA 故障码维修指导 Repair guidance for APA fault code
APA 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
APA 故障码维修指导 Repair guidance for APA fault code
故障码
故障码描述 DTC Description
DTC
2-2
APA 故障码维修指导 Repair guidance for APA fault code
故障码
故障码描述 DTC Description
DTC
2-3
APA 故障码维修指导 Repair guidance for APA fault code
APA 故障详解
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-4
APA 故障码维修指导 Repair guidance for APA fault code
2-5
APA 故障码维修指导 Repair guidance for APA fault code
2-6
APA 故障码维修指导 Repair guidance for APA fault code
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-7
APA 故障码维修指导 Repair guidance for APA fault code
2-8
APA 故障码维修指导 Repair guidance for APA fault code
2-9
APA 故障码维修指导 Repair guidance for APA fault code
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-10
APA 故障码维修指导 Repair guidance for APA fault code
2-11
APA 故障码维修指导 Repair guidance for APA fault code
2-12
APA 故障码维修指导 Repair guidance for APA fault code
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-13
APA 故障码维修指导 Repair guidance for APA fault code
2-14
APA 故障码维修指导 Repair guidance for APA fault code
2-15
APA 故障码维修指导 Repair guidance for APA fault code
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-16
APA 故障码维修指导 Repair guidance for APA fault code
2-17
APA 故障码维修指导 Repair guidance for APA fault code
2-18
APA 故障码维修指导 Repair guidance for APA fault code
可能的影响 雷达故障 ,BSD 指示灯点亮 Possible Radar fault,The BSD indicator lights up
Symptom
Possible Radar fault,The BSD indicator lights up
Symptom 故障诊断码 KL15 环境
的运行条件
故障诊断码 KL15 环境
的运行条件 Release KL15 condition
condition
Release KL15 condition
condition 故障诊断码 出现 DTC
的判断条件
故障诊断码 出现 DTC
的判断条件 Failure Appear DTC
criteria
Failure Appear DTC
criteria 故障治愈条 检查线束
件
故障治愈条 检查线束
件 Healing Check the wiring harness
condition
Healing Check the wiring harness
condition
2-19
APA 故障码维修指导 Repair guidance for APA fault code
2-20
APA 故障码维修指导 Repair guidance for APA fault code
2-21
APA 故障码维修指导 Repair guidance for APA fault code
故障发生的 线束 故障发生的 整车
可能原因 可能原因
Possible Wiring harness Possible Vehicle
Cause Cause
检查项目 线束 检查项目 整车
Check Wiring harness Check Vehicle
Items Items
2-22
APA 故障码维修指导 Repair guidance for APA fault code
故障发生的 整车 故障发生的 线束
可能原因 可能原因
Possible Vehicle Possible Wiring harness
Cause Cause
检查项目 整车 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-23
APA 故障码维修指导 Repair guidance for APA fault code
故障发生的 线束 故障发生的 线束
可能原因 可能原因
Possible Wiring harness Possible Wiring harness
Cause Cause
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-24
APA 故障码维修指导 Repair guidance for APA fault code
2-25
APA 故障码维修指导 Repair guidance for APA fault code
2-26
APA 故障码维修指导 Repair guidance for APA fault code
2-27
APA 故障码维修指导 Repair guidance for APA fault code
2-28
APA 故障码维修指导 Repair guidance for APA fault code
2-29
APA 故障码维修指导 Repair guidance for APA fault code
2-30
APA 故障码维修指导 Repair guidance for APA fault code
2-31
APA 故障码维修指导 Repair guidance for APA fault code
2-32
BCM 故障码维修指导 Repair guidance for BCM fault code
BCM 故障码维修指导 Repair guidance for BCM fault code
BCM 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
U0121-87 与 EMS 通讯 CAN 信号超时,节点丢失 Missing message CAN EMS Communication time out
U0155-87 与 IPK 通讯 CAN 信号超时,节点丢失 Missing message CAN IPK Communication time out
U0151-87 与 SRS 通讯 CAN 信号超时,节点丢失 Missing message CAN SRS Communication time out
U0101-87 与 TCU 通讯 CAN 信号超时,节点丢失 Missing message CAN TCU Communication time out
U0152-87 与 ESP 通讯 CAN 信号超时,节点丢失 Missing message CAN ESP Communication time out
U0154-87 与 SAS 通讯 CAN 信号超时,节点丢失 Missing message CAN SAS Communication time out
2-1
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码
故障码描述 DTC Description
DTC
2-2
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码
故障码描述 DTC Description
DTC
Bus signal/message
B1507-08 防盗基站通讯错误
failure Basestation Communication Error
信号比较失败,VIN 码不等于 IPK 中的 Signal compare failure VIN not equal with IPK’
U0424-62
VIN 码 s
2-3
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码
故障码描述 DTC Description
DTC
B1166-11 KL15 继电器 IG1 输出电路对地短路 KL15 Relay IG1 Circuit short to ground
2-4
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码
故障码描述 DTC Description
DTC
U1548-00 右前窗模块霍尔传感器错误 FR(Front Right) Power Window Module Hall Sensor Error
2-5
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码
故障码描述 DTC Description
DTC
2-6
BCM 故障码维修指导 Repair guidance for BCM fault code
BCM 故障详解
2-7
BCM 故障码维修指导 Repair guidance for BCM fault code
2-8
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码 U0155-87
故障码 U0121-87 DTC
DTC
故障码描述 与 IPK 通讯 CAN 信号超时,节点丢失
故障码描述 与 EMS 通讯 CAN 信号超时,节点丢失
DTC Missing message CAN IPK
DTC Missing message CAN EMS Description Communication time out
Description Communication time out
故障发生的 与 IPK 通讯 CAN 信号超时
故障发生的 与 EMS 通讯 CAN 信号超时 可能原因
可能原因
Possible CAN With IPK Communication time out
Possible CAN With EMS Communication time out Cause
Cause
检查项目 CAN 总线
检查项目 CAN 总线
Check CAN BUS
Check CAN BUS Items
Items
可能的影响 BCM 功能受限
可能的影响 BCM 功能受限
Possible BCM Functional limitation
Possible BCM Functional limitation Symptom
Symptom
2-9
BCM 故障码维修指导 Repair guidance for BCM fault code
2-10
BCM 故障码维修指导 Repair guidance for BCM fault code
2-11
BCM 故障码维修指导 Repair guidance for BCM fault code
2-12
BCM 故障码维修指导 Repair guidance for BCM fault code
2-13
BCM 故障码维修指导 Repair guidance for BCM fault code
2-14
BCM 故障码维修指导 Repair guidance for BCM fault code
2-15
BCM 故障码维修指导 Repair guidance for BCM fault code
2-16
BCM 故障码维修指导 Repair guidance for BCM fault code
2-17
BCM 故障码维修指导 Repair guidance for BCM fault code
2-18
BCM 故障码维修指导 Repair guidance for BCM fault code
2-19
BCM 故障码维修指导 Repair guidance for BCM fault code
2-20
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码 U1535-00
DTC
2-21
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码 U1537-00
DTC
故障码 U1539-00
故障码描述 光雨量传感器顶部光线传感器异常 DTC
DTC General Failure Information RLS(Rain 故障码描述 光雨量传感器工作电压过高
Description Light Sensor) auto config error
DTC General Failure Information RLS(Rain
故障发生的 光雨量传感器顶部光线传感器异常 Description Light Sensor) Powerup is more than
可能原因 High-Voltage
Possible General Failure Information RLS(Rain 故障发生的 光雨量传感器工作电压过高
Cause Light Sensor) auto config error 可能原因
检查项目 光雨量传感器 Possible General Failure Information RLS(Rain
Cause Light Sensor) Powerup is more than
Check Rain sensor
High-Voltage
Items
检查项目 光雨量传感器工作电压
可能的影响 光雨量传感器功能受限
Check Rain sensor work voltage
Possible Rain sensor Functional limitation
Items
Symptom
可能的影响 光雨量传感器功能受限
Possible Rain sensor Functional limitation
Symptom
2-22
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码 U153B-00
DTC 故障码 B1401-77
DTC
故障码描述 光雨量传感器的雨刮信号异常,欠刮,持
续 3s 故障码描述 前雨刮堵转
DTC General Failure Information RLS(Rain DTC Front wiper stall
Description Light Sensor)'sWiper always Stops at the Description
Park Position
故障发生的 前雨刮堵转
故障发生的 光雨量传感器的雨刮信号异常,欠刮,持 可能原因
可能原因 续 3s
Possible Front wiper stall
Possible General Failure Information RLS(Rain Cause
Cause Light Sensor)'sWiper always Stops at the
Park Position 检查项目 前雨刮
2-23
BCM 故障码维修指导 Repair guidance for BCM fault code
2-24
BCM 故障码维修指导 Repair guidance for BCM fault code
2-25
BCM 故障码维修指导 Repair guidance for BCM fault code
2-26
BCM 故障码维修指导 Repair guidance for BCM fault code
2-27
BCM 故障码维修指导 Repair guidance for BCM fault code
2-28
BCM 故障码维修指导 Repair guidance for BCM fault code
2-29
BCM 故障码维修指导 Repair guidance for BCM fault code
2-30
BCM 故障码维修指导 Repair guidance for BCM fault code
2-31
BCM 故障码维修指导 Repair guidance for BCM fault code
2-32
BCM 故障码维修指导 Repair guidance for BCM fault code
2-33
BCM 故障码维修指导 Repair guidance for BCM fault code
2-34
BCM 故障码维修指导 Repair guidance for BCM fault code
2-35
BCM 故障码维修指导 Repair guidance for BCM fault code
2-36
BCM 故障码维修指导 Repair guidance for BCM fault code
2-37
BCM 故障码维修指导 Repair guidance for BCM fault code
2-38
BCM 故障码维修指导 Repair guidance for BCM fault code
故障码 B100A-12
DTC
故障码描述 位置灯输出电路对电源短路
DTC Circuit short to battery Position lamp
Description output short to battery
故障发生的 位置灯输出电路对地短路
可能原因
Possible Position lamp output short to battery
Cause
检查项目 位置灯输出电路
Check Position lamp
Items
可能的影响 位置灯功能受限
Possible Position lamp Functional limitation
Symptom
2-39
BCM 故障码维修指导 Repair guidance for BCM fault code
2-40
EPB 故障码维修指导 Repair guidance for EPB fault code
EPB 故障码维修指导 Repair guidance for EPB fault code
EPB 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
U0001-88 CAN 总线 bus off CAN controller has detected Bus Off condition
U300A-29 电源硬线和 CAN 网络信号不一致 Inconsistent Ignition status data (CAN and HW)
2-1
EPB 故障码维修指导 Repair guidance for EPB fault code
EPB 故障详解
2-2
EPB 故障码维修指导 Repair guidance for EPB fault code
故障码 U0122-87
DTC 故障码 U0001-87
DTC
故障码描述 ESP( 电子稳定系统 ) 节点信息丢失
故障码描述 CAN 总线 信息丢失
DTC Atleast one CAN message from
Description ESP(Electronic Stability Program) Node DTC No CAN message received at all
is missing Description
2-3
EPB 故障码维修指导 Repair guidance for EPB fault code
2-4
EPB 故障码维修指导 Repair guidance for EPB fault code
Possible * High impedance connection from ECU Possible * Motor or actuator fault on one side
Cause to Actuator Cause * Incoherent brake states or unknown
* Actuator internal failure brakestate in EEPROM
* There is No Disc
检查项目 * 维修执行器或排除执行器马达故障 (如
检查项目 * 检查 EPB 执行器是否正确安装 有)
* 关闭 / 接通点火开关,通过 EPB 开关施 * 通过开关将制动器调节至指定状态
加制动
Check * repair actuator or actuator motor faults
* 如果 DTC (故障码)仍然存在,则更 Items if present
换受影响的执行器
* bring brakes to a defined state with
Check *Check EPB actuator for correct actuating via switch
Items mounting
可能的影响 AutoApply/EAR 禁用
*Perform ignition off / on, apply the brake
via EPB switch Possible AutoApply / EAR inhibited
*If DTC is still present replace the Symptom
affected actuator
可能的影响 EAR 禁用
Possible EAR inhibited
Symptom
2-5
EPB 故障码维修指导 Repair guidance for EPB fault code
可能的影响 手动功能全部禁用
故障码 U1560-68
Possible Manual function are all inhibited DTC
Symptom
故障码描述 电源故障,突然断电
DTC Unexpect power down
Description
故障码 C1906-49
故障发生的 * 因 ECU 重置,运行中断
DTC
可能原因 * EPB 运行中电源突然断电 (电源电压
故障码描述 控制器内部故障 低、蓄电池缺电、蓄电池有缺陷)
2-6
EPB 故障码维修指导 Repair guidance for EPB fault code
2-7
EPB 故障码维修指导 Repair guidance for EPB fault code
2-8
EPB 故障码维修指导 Repair guidance for EPB fault code
Possible -
可能的影响 RWU/DAA/EAR 禁用
Symptom
Possible RWU / DAA / EAR inhibited
Symptom
2-9
EPB 故障码维修指导 Repair guidance for EPB fault code
2-10
FICM 故障码维修指导 Repair guidance for FICM fault code
FICM 故障码维修指导 Repair guidance for FICM fault code
FICM 故障码及故障类型描述汇总
Description on the fault code and faIilure type
故障码
故障类型描述 DTC Description
P-Code
U1500-00 VIN 与 BCM (或 IPK)里面的不一致 VIN Mismatch with BCM (or IPK)
3-1
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码
故障类型描述 DTC Description
P-Code
B1A27-01 TBOX 的 USB 端口电源错误 Power of USB port for TBOX Error
3-2
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码
故障类型描述 DTC Description
P-Code
3-3
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码
故障类型描述 DTC Description
P-Code
3-4
FICM 故障码维修指导 Repair guidance for FICM fault code
FICM 故障详解
故障码 U1562-17
DTC
1 不显示 1 No display
2 不带收音机 2 No Audio
3 没有无线电收音机 3 No tuner
4 总线开 4 CAN on
3-5
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 U1563-16
DTC
1 不显示 1 No display
2 不带收音机 2 No Audio
3 没有无线电收音机 3 No tuner
4 总线开 4 CAN on
3-6
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-7
FICM 故障码维修指导 Repair guidance for FICM fault code
3-8
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-9
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-10
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
3-11
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-12
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-13
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-14
FICM 故障码维修指导 Repair guidance for FICM fault code
3-15
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件 硬件结构 软件
Hardware Software Hardware Software
structure structure
3-16
FICM 故障码维修指导 Repair guidance for FICM fault code
3-17
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A10-12
DTC
3-18
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A10-11
DTC
3-19
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A10-13
DTC
3-20
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A10-19
DTC
3-21
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A20-11
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右前扬声器
3-22
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A20-12
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右前扬声器
3-23
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A20-1A
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右前扬声器
3-24
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A20-1B
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右前扬声器
3-25
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A21-11
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有左前扬声器
3-26
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A21-12
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有左前扬声器
3-27
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A21-1A
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有左前扬声器
3-28
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A21-1B
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有左前扬声器
3-29
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A22-11
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右后扬声器
3-30
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A22-12
DTC
故障发生的可能 1 线路接错
原因
2 器件损坏
检查项目 硬件电路
可能的影响 没有右后扬声器
3-31
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A22-1A
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有右后扬声器
3-32
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A22-1B
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有右后扬声器
3-33
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A23-11
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有左后扬声器
3-34
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A23-12
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有左后扬声器
3-35
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A23-1A
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有左后扬声器
3-36
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A23-1B
DTC
故障发生的可能 线路接错
原因
检查项目 硬件电路
可能的影响 没有左后扬声器
3-37
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A27-01
DTC
故障发生的可能 1 USB 损坏
原因
2 电源不正常
检查项目 硬件电路
3-38
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A24-01
DTC
故障发生的可能 1 USB 损坏
原因
2 电源不正常
检查项目 硬件电路
3-39
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A26-01
DTC
故障发生的可能 1 USB 损坏
原因
2 电源不正常
检查项目 硬件电路
3-40
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A25-12
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦功能
3-41
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A25-11
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦功能
3-42
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A25-13
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦功能
3-43
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A28-12
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦功能
3-44
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A28-11
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦 2 功能
3-45
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A28-13
DTC
故障发生的可能 1 电路连接错误
原因
2 线路损坏
检查项目 硬件电路
可能的影响 没有麦 2 功能
3-46
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A4C-71
DTC
3-47
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A4E-71
DTC
3-48
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A4D-71
DTC
3-49
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A3E-71
DTC
3-50
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A3F-71
DTC
3-51
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A01-71
DTC
3-52
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A02-71
DTC
3-53
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A05-71
DTC
3-54
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A06-71
DTC
3-55
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A07-71
DTC
3-56
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A08-71
DTC
3-57
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A4B-71
DTC
3-58
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A43-11
DTC
3-59
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A43-15
DTC
3-60
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A44-11
DTC
3-61
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1A44-15
DTC
3-62
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE0-14
DTC
360 左摄像头的视频信号电路对接地短路或开路 360 Left Camera Video Signal Circuit Short to Ground or Open
3-63
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE0-12
DTC
360 左摄像头的视频信号电路对电源短路 360 Left Camera Video Signal Circuit Short to Battery
3-64
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE1-14
DTC
360 右摄像头的视频信号电路对接地短路或开路 360 Right Camera Video Signal Circuit Short to Ground or Open
3-65
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE1-12
DTC
360 右摄像头的视频信号电路对电源短路 360 Right Camera Video Signal Circuit Short to Battery
3-66
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE2-14
DTC
360 前置摄像头的视频信号电路对接地短路或开路 360 Front Camera Video Signal Circuit Short to Ground or Open
3-67
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE2-12
DTC
360 前置摄像头的视频信号电路对电源短路 360 Front Camera Video Signal Circuit Short to Battery
3-68
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE3-14
DTC
360 后置摄像头视频信号电路对接地短路或开路 360 Rear Camera Video Signal Circuit Short to Ground or Open
3-69
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE3-12
DTC
360 后置摄像头的视频信号电路对电源短路 360 Rear Camera Video Signal Circuit Short to Battery
3-70
FICM 故障码维修指导 Repair guidance for FICM fault code
故障码 B1AE4-12
DTC
3-71
FICM 故障码维修指导 Repair guidance for FICM fault code
硬件结构 软件
Hardware Software
structure
故障发生的 1 通讯一方故障
可能原因
2 网络故障
Possible 1 Communication fault
Cause
2 Network fault
检查项目 模块通信检测
Check Module communication detection
Items
3-72
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
故障码
故障码描述 DTC Description
DTC
4-1
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
故障码
故障码描述 DTC Description
DTC
4-2
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
可能的影响 不能接收到来自 ABS/ESP 的所有报文 Possible Can not accept all from SAS message
Symptom
Possible Can not accept all from ABS/EPS
Symptom message
4-3
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-4
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-5
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-6
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-7
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
5 CAN_L and power supply circuit Possible Can not accept all from ALC message
Symptom
6 CAN_L and short circuit
检查项目 1 检查线束
2 检查娱乐主机接插件
Check 1 Check the wiring harness
Items
2 Check the entertainment host
connectors
可能的影响 无 CAN 通信
Possible Without the CAN communication
Symptom
4-8
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-9
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-10
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-11
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-12
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-13
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-14
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
故障码 B0263-14
DTC
检查项目 1 检查线束
2 检查主机 USB 电源输出线路
Check 1 Check the wiring harness
Items
2 Check the host USB power
output line
4-15
Colour radio 故障码维修指导 Repair guidance for Colour radio fault code
4-16
GAW 故障码维修指导 Repair guidance for GAW fault code
GAW 故障码维修指导 Repair guidance for GAW fault code
GAW 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障类型描述 DTC Description
P-Code
5-1
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码
故障类型描述 DTC Description
P-Code
U0142-87 与 PLG( 电动移门 ) 通讯丢失 Lost Communication With PLG(Power lift Gate)
5-2
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码
故障类型描述 DTC Description
P-Code
电可擦只读存取器 ( 非易失性存储器 )
B162F-42 EEPROM(NVM(Nonvolatile memory)Error
错误
5-3
GAW 故障码维修指导 Repair guidance for GAW fault code
GAW 故障详解
可能的影响 没有 CAN 通信
Possible No CAN Communication
Symptom
故障码 U1563-16
DTC
故障码描述 系统蓄电池电压过低
DTC Battery voltage is too low 故障码 U0074-88
Description DTC
Possible Battery Voltage Low DTC Control Module Communication Bus Off
Cause Description on CH(Chassis) CAN
可能的影响 没有 CAN 通信
Possible No CAN Communication
Symptom
5-4
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 U0076-88
DTC
故障码 U0140-87
故障码描述 Info( 娱乐信息 ) CAN 上的控制器通讯总
DTC
线关闭
DTC Control Module Communication Bus Off 故障码描述 与 BCM( 车身控制管理系统 ) 通讯丢失
Description on Info(Entertainment Information) DTC Lost Communication With BCM(Body
CAN Description Control Management)
故障发生的 Info CAN 总线短路 故障发生的 KL.15 ON 时 , 在规定的时间内没有收到
可能原因 可能原因 报文
Possible Info CAN Bus shorted Possible No message received within the
Cause Cause defined time slot at KL.15 ON
检查项目 1 检查线束 检查项目 1 检查线束
2 检查 GAW 接插件 2 检查 GAW 接插件
Check Items 1 Check harness 3 检查 BCM
2 Check connector Check Items 1 Check harness
可能的影响 没有 CAN 通信 2 Check connector
Possible No CAN Communication 3 Check BCM
Symptom
可能的影响 BCM 丢失通信
Possible BCM lost communication
Symptom
5-5
GAW 故障码维修指导 Repair guidance for GAW fault code
5-6
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 U0119-87
故障码 U0116-87 DTC
DTC
故障码描述 与 SRS( 安全气囊 ) 通讯丢失
故障码描述 与 HVAC( 自动空调 ) 通讯丢失
DTC Lost Communication With
DTC Lost Communication With Description SRS(Supplemental Restraint System)
Description HVAC(Heating Ventilation and Air
Conditioning) 故障发生的 KL.15 ON 时 , 在规定的时间内没有收到
可能原因 报文
故障发生的 KL.15 ON 时 , 在规定的时间内没有收到
可能原因 报文 Possible No message received within the
Cause defined time slot at KL.15 ON
Possible No message received within the
Cause defined time slot at KL.15 ON 检查项目 1 检查线束
2 检查 GAW 接插件
检查项目 1 检查线束
2 检查 GAW 接插件 3 检查 SRS
5-7
GAW 故障码维修指导 Repair guidance for GAW fault code
Possible No message received within the Possible No message received within the
Cause defined time slot at KL.15 ON Cause defined time slot at KL.15 ON
3 检查 AFS 3 检查 TPMS
5-8
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 B162F-42
故障码 U0126-87 DTC
DTC
故障码描述 电可擦只读存取器 ( 非易失性存储器 )
故障码描述 与 ABS_ESP 通讯丢失 错误
DTC Lost Communication With ABS_ESP DTC EEPROM(NVM(Nonvolatile memory))
Description Description Error
3 Check ABS_ESP
5-9
GAW 故障码维修指导 Repair guidance for GAW fault code
5-10
GAW 故障码维修指导 Repair guidance for GAW fault code
5-11
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 U0162-87
DTC
故障码 U0164-87
故障码描述 AWDSM( 适时四驱模式开关系统 ) 回复 DTC
错误
故障码描述 AWDSM( 适时四驱模式开关系统 )4H(
DTC AWDSM(Automatic Four-wheel drive 高速四驱 ) 开关粘贴
Description switching system) response error
DTC AWDSM(Automatic Four-wheel drive
故障发生的 LIN 反馈 AWDSM( 适时四驱模式开关系 Description switching system) 4H(High-speed four-
可能原因 统 ) 回复错误 wheel drive) switch stick
Possible LIN feedback AWDSM(Automatic Four- 故障发生的 LIN 反馈 AWDSM( 适时四驱模式开关系
Cause wheel drive switching system) 可能原因 统 )4H( 高速四驱 ) 开关粘贴
response error
Possible LIN feedback AWDSM(Automatic Four-
检查项目 检查 AWDSM Cause wheel drive switching system)
4H(High-speed four-wheel drive) switch
Check Items Check AWDSM
stick
可能的影响 AWDSM( 适时四驱模式开关系统 ) 回复
检查项目 检查 AWDSM
错误
Check Items Check AWDSM
Possible AWDSM(Automatic Four-wheel drive
Symptom switching system) response error 可能的影响 AWDSM( 适时四驱模式开关系统 )4H(
高速四驱 ) 开关粘贴
Possible AWDSM(Automatic Four-wheel drive
Symptom switching system) 4H(High-speed four-
wheel drive) switch stick
5-12
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 U0166-87
DTC
故障码 U0168-87
故障码描述 AWDSM( 适时四驱模式开关系统 ) 自动 DTC
开关粘贴
故障码描述 与 ATSSM( 全地形模式开关系统 ) 通讯
DTC AWDSM(Automatic Four-wheel drive 丢失
Description switching system) AUTO switch stick
DTC Lost Communication With ATSSM(All
故障发生的 LIN 反馈 AWDSM( 适时四驱模式开关系 Description Terrain System Switch Mode)
可能原因 统 ) 自动开关粘贴
故障发生的 KL.15 ON 时 , 在规定的时间内没有收到
Possible LIN feedback AWDSM(Automatic Four- 可能原因 报文
Cause wheel drive switching system) AUTO
Possible No message received within the
switch stick
Cause defined time slot at KL.15 ON
检查项目 检查 AWDSM
检查项目 1 检查线束
Check Items Check AWDSM 2 检查 GAW 接插件
可能的影响 AWDSM( 适时四驱模式开关系统 ) 自动 3 检查 ATSSM
开关粘贴
Check Items 1 Check harness
Possible AWDSM(Automatic Four-wheel drive
Symptom switching system) AUTO switch stick 2 Check connector
3 Check ATSSM
5-13
GAW 故障码维修指导 Repair guidance for GAW fault code
故障码 U2001-41
DTC
检查项目 检查产品芯片
Check Items Check GAW chips
5-14
PEPS 故障码维修指导 Repair guidance for PEPS fault code
PEPS 故障码维修指导 Repair guidance for PEPS fault code
PEPS 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障类型描述 DTC Description
P-Code
6-1
PEPS 故障码维修指导 Repair guidance for PEPS fault code
故障码
故障类型描述 DTC Description
P-Code
B13C2-51 没有钥匙信息 (无已学习的钥匙) No key fob information (No key fob is learnt)
6-2
PEPS 故障码维修指导 Repair guidance for PEPS fault code
PEPS 故障详解
6-3
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-4
PEPS 故障码维修指导 Repair guidance for PEPS fault code
DTC Low frequency antenna driver error DTC ACC Relay Error
Description Description
6-5
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-6
PEPS 故障码维修指导 Repair guidance for PEPS fault code
故障发生的 1 EMS 控制器 CAN 总线接插件接 故障发生的 1 TCU 控制器 CAN 总线接插件接
可能原因 可能原因 触不良或未连接
触不良或未连接
2 EMS 控制器通信故障 2 TCU 控制器通信故障
6-7
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-8
PEPS 故障码维修指导 Repair guidance for PEPS fault code
故障发生的 1 EMS 控制器 CAN 总线接插件接 故障发生的 1 ABS/ESP 控制器 CAN 总线接插
可能原因 可能原因 件接触不良或未连接
触不良或未连接
2 EMS 控制器通信故障 2 ABS/ESP 控制器通信故障
6-9
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-10
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-11
PEPS 故障码维修指导 Repair guidance for PEPS fault code
DTC SSB(Start Stop Button) switch error DTC Gear shift “P” error
Description (stuck) Description
6-12
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-13
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-14
PEPS 故障码维修指导 Repair guidance for PEPS fault code
2 钥匙在车内无法正常启动车辆 2 更换防盗基站
可能的影响 1 车辆无法学习钥匙
2 车辆无法备份启动
故障码 B13C3-62 Possible 1 Vehicle cannot perform a key
DTC Symptom learning
故障码描述 EMS( 发动机管理系统)验证失败 2 Vehicle backup start fails
DTC EMS(Engine Management System)
Description authentication failure
可能的影响 车辆无法启动
Possible Vehicle cannot be started
Symptom
6-15
PEPS 故障码维修指导 Repair guidance for PEPS fault code
6-16
SRS 故障码维修指导 Repair guidance for SRS fault code
SRS 故障码维修指导 Repair guidance for SRS fault code
SRS 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-2
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-3
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-4
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-5
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-6
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
Crash Output(Hardwired)
B120D-55 碰撞输出配置错误
Unexpected(configuration error)
2-7
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
传感器的识别码于算法预定的识别码不一
B0053-01 Algo Verify Sensor Id Not Match
致
2-8
SRS 故障码维修指导 Repair guidance for SRS fault code
故障码
故障码描述 DTC Description
DTC
2-9
SRS 故障码维修指导 Repair guidance for SRS fault code
SRS 故障详解
检查项目 线束 检查项目 线束
Check Wring harness Check Wring harness
Items Items
2-10
SRS 故障码维修指导 Repair guidance for SRS fault code
2-11
SRS 故障码维修指导 Repair guidance for SRS fault code
2-12
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-13
SRS 故障码维修指导 Repair guidance for SRS fault code
2-14
SRS 故障码维修指导 Repair guidance for SRS fault code
2-15
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-16
SRS 故障码维修指导 Repair guidance for SRS fault code
2-17
SRS 故障码维修指导 Repair guidance for SRS fault code
2-18
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-19
SRS 故障码维修指导 Repair guidance for SRS fault code
2-20
SRS 故障码维修指导 Repair guidance for SRS fault code
2-21
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-22
SRS 故障码维修指导 Repair guidance for SRS fault code
2-23
SRS 故障码维修指导 Repair guidance for SRS fault code
2-24
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-25
SRS 故障码维修指导 Repair guidance for SRS fault code
2-26
SRS 故障码维修指导 Repair guidance for SRS fault code
2-27
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-28
SRS 故障码维修指导 Repair guidance for SRS fault code
2-29
SRS 故障码维修指导 Repair guidance for SRS fault code
2-30
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-31
SRS 故障码维修指导 Repair guidance for SRS fault code
2-32
SRS 故障码维修指导 Repair guidance for SRS fault code
2-33
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-34
SRS 故障码维修指导 Repair guidance for SRS fault code
2-35
SRS 故障码维修指导 Repair guidance for SRS fault code
2-36
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-37
SRS 故障码维修指导 Repair guidance for SRS fault code
2-38
SRS 故障码维修指导 Repair guidance for SRS fault code
2-39
SRS 故障码维修指导 Repair guidance for SRS fault code
2-40
SRS 故障码维修指导 Repair guidance for SRS fault code
2-41
SRS 故障码维修指导 Repair guidance for SRS fault code
2-42
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-43
SRS 故障码维修指导 Repair guidance for SRS fault code
2-44
SRS 故障码维修指导 Repair guidance for SRS fault code
2-45
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-46
SRS 故障码维修指导 Repair guidance for SRS fault code
2-47
SRS 故障码维修指导 Repair guidance for SRS fault code
2-48
SRS 故障码维修指导 Repair guidance for SRS fault code
2-49
SRS 故障码维修指导 Repair guidance for SRS fault code
2-50
SRS 故障码维修指导 Repair guidance for SRS fault code
2-51
SRS 故障码维修指导 Repair guidance for SRS fault code
2-52
SRS 故障码维修指导 Repair guidance for SRS fault code
2-53
SRS 故障码维修指导 Repair guidance for SRS fault code
2-54
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-55
SRS 故障码维修指导 Repair guidance for SRS fault code
2-56
SRS 故障码维修指导 Repair guidance for SRS fault code
2-57
SRS 故障码维修指导 Repair guidance for SRS fault code
2-58
SRS 故障码维修指导 Repair guidance for SRS fault code
检查项目 线束 检查项目 线束
Check Wiring harness Check Wiring harness
Items Items
2-59
SRS 故障码维修指导 Repair guidance for SRS fault code
2-60
SRS 故障码维修指导 Repair guidance for SRS fault code
2-61
SRS 故障码维修指导 Repair guidance for SRS fault code
2-62
SRS 故障码维修指导 Repair guidance for SRS fault code
2-63
SRS 故障码维修指导 Repair guidance for SRS fault code
2-64
SRS 故障码维修指导 Repair guidance for SRS fault code
2-65
SRS 故障码维修指导 Repair guidance for SRS fault code
2-66
SRS 故障码维修指导 Repair guidance for SRS fault code
2-67
SRS 故障码维修指导 Repair guidance for SRS fault code
2-68
SRS 故障码维修指导 Repair guidance for SRS fault code
2-69
SRS 故障码维修指导 Repair guidance for SRS fault code
2-70
SRS 故障码维修指导 Repair guidance for SRS fault code
2-71
SRS 故障码维修指导 Repair guidance for SRS fault code
2-72
SRS 故障码维修指导 Repair guidance for SRS fault code
2-73
SRS 故障码维修指导 Repair guidance for SRS fault code
2-74
SRS 故障码维修指导 Repair guidance for SRS fault code
2-75
SRS 故障码维修指导 Repair guidance for SRS fault code
2-76
SRS 故障码维修指导 Repair guidance for SRS fault code
故障治愈条 检查网络信号
件
Healing Check network signal
condition
2-77
SRS 故障码维修指导 Repair guidance for SRS fault code
2-78
SRS 故障码维修指导 Repair guidance for SRS fault code
2-79
SRS 故障码维修指导 Repair guidance for SRS fault code
2-80
SRS 故障码维修指导 Repair guidance for SRS fault code
故障治愈条 检查线束
件
Healing Check the wiring harness
condition
2-81
SRS 故障码维修指导 Repair guidance for SRS fault code
2-82
SRS 故障码维修指导 Repair guidance for SRS fault code
2-83
SRS 故障码维修指导 Repair guidance for SRS fault code
2-84
TBOX 故障码维修指导 Repair guidance for TBOX fault code
TBOX 故障码维修指导 Repair guidance for TBOX fault code
TBOX 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
TBOX( 远程监控模块 ) GPS 天线对地短 TBOX(Telematics Box) GPS Antenna short to GND
B1521-11
路 fault
B1526-31 TBOX( 远程监控模块 ) GSM 模块故障 TBOX(Telematics Box) GSM Module fault
TBOX( 远程监控模块 ) 内置 SIM 卡状态 TBOX(Telematics Box) Internal SIM Card Status
B1541-00
不存在 - Not Present
2-1
TBOX 故障码维修指导 Repair guidance for TBOX fault code
TBOX 故障详解
故障码描述 TBOX( 远程监控模块 ) GPS 天线对地短 故障码描述 TBOX( 远程监控模块 ) GPS 天线对电源
路 短路
DTC TBOX(Telematics Box) GPS Antenna DTC TBOX(Telematics Box) GPS Antenna
Description short to GND fault Description short to Battery
2-2
TBOX 故障码维修指导 Repair guidance for TBOX fault code
故障码描述 TBOX( 远程监控模块 ) GPS 天线开路故 故障码描述 TBOX( 远程监控模块 ) GSM 天线对地短
障 路
DTC TBOX(Telematics Box) GPS Antenna DTC TBOX(Telematics Box) GSM Antenna
Description open fault Description short to Ground
2-3
TBOX 故障码维修指导 Repair guidance for TBOX fault code
故障码 B1533-11
故障码 B1526-31 DTC
DTC
故障码描述 麦克风输入对地短路
故障码描述 TBOX( 远程监控模块 ) GSM 模块故障
DTC Microphone Input short to Ground
DTC TBOX(Telematics Box) GSM Module Description
Description fault
故障发生的 麦克风输入对地短路
故障发生的 GSM 模块故障 可能原因
可能原因
Possible Microphone Input short to Ground
Possible GSM Module fault Cause
Cause
检查项目 Microphone 或电缆接口及线束
检查项目 GSM 接插件及线束
Check Check the microphone, or check the
Check Check the T-BOX WAN-FAKRA Code D Items connect cable interface
Items Connector, or exchange the WAN ANT
or Exchange the T-BOX 可能的影响 TBOX 语音功能受限
可能的影响 TBOX WAN 功能受限 Possible TBOX don't provide Voice Service
Symptom
Possible TBOX WAN service function disabled
Symptom
2-4
TBOX 故障码维修指导 Repair guidance for TBOX fault code
2-5
TBOX 故障码维修指导 Repair guidance for TBOX fault code
故障码 U1500-62
DTC 故障码 U1563-16
DTC
故障码描述 VIN 与 BCM( 车身控制管理系统 ) (或
IPK( 仪表 ))里的不匹配 故障码描述 电池电压低
DTC VIN Mismatch with BCM(Body Control DTC Battery Voltage Low
Description Management) (or IPK(Instrument Park)) Description
2-6
TBOX 故障码维修指导 Repair guidance for TBOX fault code
故障码 U2001-42
故障码 U0146-87 DTC
DTC
故障码描述 控制器 EEPROM( 电可擦只读存取器 ) 故
故障码描述 与网关 (GAW) 通讯丢失 障
DTC Lost Communication With DTC ECU EEPROM Error
Description Gateway(GAW) Description
可能的影响 - 可能的影响 -
Possible - Possible -
Symptom Symptom
2-7
TBOX 故障码维修指导 Repair guidance for TBOX fault code
2-8
TCCU 故障码维修指导 Repair guidance for TCCU fault code
TCCU 故障码维修指导 Repair guidance for TCCU fault code
TCCU 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
TCCU 故障码维修指导 Repair guidance for TCCU fault code
故障码
故障码描述 DTC Description
DTC
2-2
TCCU 故障码维修指导 Repair guidance for TCCU fault code
TCCU 故障详解
4 No Bus-off Occurs
2-3
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
2-4
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
Release 1 Voltage supply is within 情况一:
condition 9.75V~15.25V 5 Variant TransType == AT (自动
2 IG ON 变速器)
4 No Bus-off Occurs
CASE 1:
5 Variant TransType == AT
CASE 2:
5 Variant TransType == Manual
2-5
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
Release 1 Voltage supply is within Release 1 Voltage supply is within
condition 9.75V~15.25V condition 9.75V~15.25V
2 IG ON 2 IG ON
2-6
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
5 Variant ATSType == ATS 5 Variant ATSType == NO ATS
Release 1 Voltage supply is within Release 1 Voltage supply is within
condition 9.75V~15.25V condition 9.75V~15.25V
2 IG ON 2 IG ON
2-7
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
5 Variant TransType == Manual 5 信息未丢失
(手动变速器) Release 1 Voltage supply is within
Release 1 Voltage supply is within condition 9.75V~15.25V
condition 9.75V~15.25V 2 IG ON
2 IG ON
3 1.5s general diagnotic delay
3 1.5s general diagnotic delay time elapsed
time elapsed
4 No Bus-off Occurs
4 No Bus-off Occurs
5 Message not missing
5 Variant TransType == Manual
2-8
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
2-9
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
2-10
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
6 Variant TransType == AT
2-11
TCCU 故障码维修指导 Repair guidance for TCCU fault code
4 未发生总线关闭问题 4 未发生总线关闭问题
2-12
TCCU 故障码维修指导 Repair guidance for TCCU fault code
2 IG ON 故障码描述 换档电机开路
2-13
TCCU 故障码维修指导 Repair guidance for TCCU fault code
故障码 P0560-1C
DTC
故障码 P1781-12
DTC 故障码描述 系统电压超出范围
2-14
TCCU 故障码维修指导 Repair guidance for TCCU fault code
故障码 P1783-77
故障码 P1729-12
DTC
DTC
故障码描述 换档超时
故障码描述 离合器线圈对电源短路
DTC Shift System Timeout
DTC Coupling Coil Short to Battery
Description
Description
检查项目 检查换档电机硬件条件
检查项目 检查变速箱与 TCCU 硬件连接
Check Check shift motor hardware condition
Check Check the hardwire conncetion between
Items
Items transfer case and TCCU
故障诊断码 供电电压介于 9.75V~15.25V 之间;点火
故障诊断码 供电电压介于 9.75V~15.25V 之间;点火
的运行条件 开关接通
的运行条件 开关接通;线圈驱动状态从启用转换为禁
Release Voltage supply is within 9.75V - 15.25V 用后 100ms
condition AND IG ON
Release Voltage supply is within 9.75V - 15.25V
condition AND IG ON AND 100ms after coil driver
state transitions from enabled to
disabled
2-15
TCCU 故障码维修指导 Repair guidance for TCCU fault code
故障码 P1730-11
DTC
故障码描述 离合器线圈对地短路
DTC Coupling Coil Short to Ground
Description
2-16
AFS 故障码维修指导 Repair guidance for AFS fault code
AFS 故障码维修指导 Repair guidance for AFS fault code
AFS 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
B1735-87 左侧上下调节电机与 LIN 通讯丢失 Left Leveling ACTM lost communication with LIN
2-1
AFS 故障码维修指导 Repair guidance for AFS fault code
AFS 故障详解
2-2
AFS 故障码维修指导 Repair guidance for AFS fault code
2-3
AFS 故障码维修指导 Repair guidance for AFS fault code
2-4
AFS 故障码维修指导 Repair guidance for AFS fault code
2-5
AFS 故障码维修指导 Repair guidance for AFS fault code
2-6
AFS 故障码维修指导 Repair guidance for AFS fault code
2-7
AFS 故障码维修指导 Repair guidance for AFS fault code
2-8
AFS 故障码维修指导 Repair guidance for AFS fault code
2-9
AFS 故障码维修指导 Repair guidance for AFS fault code
2-10
EDL 故障码维修指导 Repair guidance for EDL fault code
EDL 故障码维修指导 Repair guidance for EDL fault code
EDL 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
EDL 故障码维修指导 Repair guidance for EDL fault code
EDL 故障详解
故障发生的 电池 故障发生的 电池
可能原因 可能原因
Possible Battery Possible Battery
Cause Cause
2-2
EDL 故障码维修指导 Repair guidance for EDL fault code
3 电压正常 3 电压正常
Release 1 After 1s ECU from sleep to Release 1 After 1s ECU from sleep to
condition wake up condition wake up
2 CAN ON 2 CAN ON
2-3
EDL 故障码维修指导 Repair guidance for EDL fault code
3 电压正常 3 电压正常
Release 1 After 1s ECU from sleep to Release 1 After 1s ECU from sleep to
condition wake up condition wake up
2 CAN ON 2 CAN ON
2-4
EDL 故障码维修指导 Repair guidance for EDL fault code
故障治愈条 故障恢复
件
Healing Err disappear
condition
2-5
EDL 故障码维修指导 Repair guidance for EDL fault code
2-6
EDL 故障码维修指导 Repair guidance for EDL fault code
故障治愈条 故障恢复
件
Healing Err disappear
condition
2-7
EDL 故障码维修指导 Repair guidance for EDL fault code
故障码 U0073-88
DTC
故障码描述 总线关闭
DTC CAN BUS OFF
Description
可能的影响 EDL 开锁
Possible Turn Edl unlock
Symptom
2-8
IPK 故障码维修指导 Repair guidance for IPK fault code
IPK 故障码维修指导 Repair guidance for IPK fault code
IPK 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
U0198-16 与 PLG( 电动移门 ) 通讯丢失 Lost communication with PLG(Power lift Gate)
2-1
IPK 故障码维修指导 Repair guidance for IPK fault code
故障码
故障码描述 DTC Description
DTC
2-2
IPK 故障码维修指导 Repair guidance for IPK fault code
IPK 故障详解
3 警告灯熄灭 3 警告灯熄灭
Possible 1 IPK cannot work Possible 1 IPK cannot work
Symptom Symptom
2 The pointer returns to zero 2 The pointer returns to zero
3 The warning lamp goes out 3 The warning lamp goes out
2-3
IPK 故障码维修指导 Repair guidance for IPK fault code
2-4
IPK 故障码维修指导 Repair guidance for IPK fault code
2-5
IPK 故障码维修指导 Repair guidance for IPK fault code
检查项目 检查 EMS
Check Check EMS
Items
2-6
IPK 故障码维修指导 Repair guidance for IPK fault code
检查项目 检查 BCM
Check Check BCM
Items
2-7
IPK 故障码维修指导 Repair guidance for IPK fault code
2-8
IPK 故障码维修指导 Repair guidance for IPK fault code
2-9
IPK 故障码维修指导 Repair guidance for IPK fault code
2-10
IPK 故障码维修指导 Repair guidance for IPK fault code
2-11
IPK 故障码维修指导 Repair guidance for IPK fault code
2-12
IPK 故障码维修指导 Repair guidance for IPK fault code
检查项目 检查 ADAS
Check Check ADAS
Items
2-13
IPK 故障码维修指导 Repair guidance for IPK fault code
2-14
IPK 故障码维修指导 Repair guidance for IPK fault code
故障码 U0300-16
DTC
检查项目 检查 VIN
Check Check VIN code
Items
2-15
IPK 故障码维修指导 Repair guidance for IPK fault code
2-16
DCDC 故障码维修指导 Repair guidance for DCDC fault code
DCDC 故障码维修指导 Repair guidance for DCDC fault code
DCDC 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
DCDC 故障码维修指导 Repair guidance for DCDC fault code
DCDC 故障详解
2-2
DCDC 故障码维修指导 Repair guidance for DCDC fault code
2-3
DCDC 故障码维修指导 Repair guidance for DCDC fault code
2-4
DCDC 故障码维修指导 Repair guidance for DCDC fault code
故障码 B1BA0-1C
DTC
检查项目 检查 / 替换 DCDC
Check Replace DCDC
Items
2-5
DCDC 故障码维修指导 Repair guidance for DCDC fault code
2-6
DSM 故障码维修指导 Repair guidance for DSM fault code
DSM 故障码维修指导 Repair guidance for DSM fault code
DSM 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
与 FICM (娱乐系统大屏含导航)通信
U0156-87 Lost Communication With FICM
丢失
与 PEPS( 无钥匙控制无钥匙启动系统 )
U0168-87 Lost Communication With PEPS
通信丢失
2-1
DSM 故障码维修指导 Repair guidance for DSM fault code
故障码
故障码描述 DTC Description
DTC
座椅滑动电机控制电路电流过大 (短
B2CA1-19 Seat Slider Motor Control Circuit Over Current
路)
座椅升降电机控制电路电流过大 (短
B2CA3-19 Seat Lifter Motor Control Circuit Over Current
路)
座椅调角电机控制电路电流过大 (短
B2CA5-19 Seat Tilter Motor Control Circuit Over Current
路)
2-2
DSM 故障码维修指导 Repair guidance for DSM fault code
DSM 故障详解
2-3
DSM 故障码维修指导 Repair guidance for DSM fault code
Possible DSM limits the adjustment function Possible DSM work locally, but some function
Symptom Symptom may be degraded due to lack of signals
from other ECUs
2-4
DSM 故障码维修指导 Repair guidance for DSM fault code
可能的影响 座椅记忆状态无法显示,功能不受影响
Possible DSM works normally, but some function
Symptom may be degraded due to lack of signals
from IPK
2-5
DSM 故障码维修指导 Repair guidance for DSM fault code
2-6
DSM 故障码维修指导 Repair guidance for DSM fault code
2-7
DSM 故障码维修指导 Repair guidance for DSM fault code
2-8
DSM 故障码维修指导 Repair guidance for DSM fault code
2-9
DSM 故障码维修指导 Repair guidance for DSM fault code
2-10
DSM 故障码维修指导 Repair guidance for DSM fault code
2-11
DSM 故障码维修指导 Repair guidance for DSM fault code
2-12
DSM 故障码维修指导 Repair guidance for DSM fault code
DTC Seat Lifter Switch Malfunction DTC Seat Tilter Switch Malfunction
Description Description
2-13
DSM 故障码维修指导 Repair guidance for DSM fault code
2-14
DSM 故障码维修指导 Repair guidance for DSM fault code
2-15
DSM 故障码维修指导 Repair guidance for DSM fault code
2-16
DSM 故障码维修指导 Repair guidance for DSM fault code
2-17
DSM 故障码维修指导 Repair guidance for DSM fault code
2-18
DSM 故障码维修指导 Repair guidance for DSM fault code
2-19
DSM 故障码维修指导 Repair guidance for DSM fault code
2-20
DSM 故障码维修指导 Repair guidance for DSM fault code
2-21
DSM 故障码维修指导 Repair guidance for DSM fault code
2-22
DSM 故障码维修指导 Repair guidance for DSM fault code
2-23
DSM 故障码维修指导 Repair guidance for DSM fault code
2-24
DSM 故障码维修指导 Repair guidance for DSM fault code
2-25
DSM 故障码维修指导 Repair guidance for DSM fault code
故障码 B2C23-1C
DTC
故障码描述 右后视镜垂直位置传感器失效
DTC Right Mirror Vertical Position Sensor
Description Failure
检查项目 1 检查右后视镜
2 检查 DSM
Check 1 Check Right Mirror
Items
2 Check DSM
2-26
EMS 故障码维修指导 Repair guidance for EMS fault code
EMS 故障码维修指导 Repair guidance for EMS fault code
EMS 故障码及故障类型描述汇总
Description on the fault code and failure type
菱
故障码
故障类型描述 DTC Description
P-Code
3-1
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-2
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-3
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
Turbocharger/Supercharger Overboost
P0234-00 增压器增压压力过高
Condition
3-4
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
Turbocharger/Supercharger Wastegate
P0243-13 增压器废气控制阀电路开路
Solenoid “A” Circuit open
Turbocharger/Supercharger Wastegate
P0245-11 增压器废气控制阀电路对地短路
Solenoid “A” Low
Turbocharger/Supercharger Wastegate
P0246-12 增压器废气控制阀电路对电源短路
Solenoid “A” High
3-5
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-6
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-7
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
ECM/PCM Processor,Watchdog/safety μ C
P0606-47 电子节气门安全监控功能故障 , 安全故障
failure
电子节气门安全监控功能故障 , 无加载测试停
P0606-64 ECM/PCM Processor,Null Load Test Pulse
止
3-8
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
P0704-00 离合器行程传感器 10% 行程信号不合 Sig Error for Clutch Position sensor
3-9
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-10
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-11
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
3-12
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
P0704-00 离合器行程传感器 10% 行程信号不合 Signal Error for Clutch Position sensor
P1500-00 EBS 的 LIN 报文校验错误 Npl error for LIN EBS diagnosis
P1501-00 EBS 的 LIN 报文帧错误 Sig error for LIN EBS diagnosis
P1502-00 EBS 的 LIN 报文接收回应时长超限 Min error for LIN EBS diagnosis
P1503-00 EBS 的 LIN 报文回读时长错误 Max error for LIN EBS diagnosis
P1530-00 发电机的 LIN 报文校验错误 Npl error for LIN generator diagnosis
P1531-00 发电机的 LIN 报文帧错误 Sig error for LIN generator diagnosis
P1532-00 发电机的 LIN 报文接收回应时长超限 Min error for LIN generator diagnosis
P1533-00 发电机的 LIN 报文回读时长错误 Max error for LIN generator diagnosis
3-13
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码
故障类型描述 DTC Description
P-Code
P0704-00 离合器行程传感器 10% 行程信号不合 Sig Error for Clutch Position sensor
3-14
EMS 故障码维修指导 Repair guidance for EMS fault code
EMS 故障详解
故障码 P000A-26
P-Code
2. 检查 OCV 机油控制阀 2.Check whether the OCV 是 Y 进行其他 Check other related
工作状况是否正常 oil control valve is working 相关部件 components
normally or not
的检查
故障码 P000A-29
P-Code
2. 检查 OCV 机油控制阀 2.Check whether the OCV 是 Y 进行其他 Check other related
工作状况是否正常 oil control valve is working 相关部件 components
normally or not
的检查
3-15
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P000B-26
P-Code
2. 检查 OCV 机油控制阀 2.Check whether the OCV 是 Y 进行其他 Check other related
工作状况是否正常 oil control valve is working 相关部件 components
normally or not
的检查
故障码 P000B-29
P-Code
2. 检查 OCV 机油控制阀 2.Check whether the OCV 是 Y 进行其他 Check other related
工作状况是否正常 oil control valve is working 相关部件 components
normally or not
的检查
3-16
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0016-76
P-Code
故障码 P0016-78
P-Code
1. 进气凸轮轴位置跳动, 1.The intake camshaft has its 是 Y 进行必要 Carry out necessary
曲轴与进气凸轮轴间传动 position beating – Check 检修 troubleshooting
齿轮、皮带等是否有故 whether failures occur to the
障,存在跳齿 transmission gears and belts 否 N 重新调整 Correct the
between the crankshaft and 正确安装 installation position
the intake camshaft and 位置 again
whether there is any gear
jumping
故障码 P0017-76
P-Code
3-17
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0017-78
P-Code
故障码 P0026-77
P-Code
3-18
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0027-77
P-Code
故障码 P0030-13
P-Code
3-19
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0031-11
P-Code
故障码 P0032-12
P-Code
3-20
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0033-13
P-Code
3-21
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0034-11
P-Code
故障码 P0035-12
P-Code
3-22
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0036-13
P-Code
3-23
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0037-11
P-Code
故障码 P0038-12
P-Code
3-24
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0053-1B
P-Code
3-25
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0054-1B
P-Code
3-26
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P006D-16
P-Code
故障码 P006D-17
P-Code
3-27
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0075-13
P-Code
故障码 P0076-11
P-Code
3-28
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0077-12
P-Code
故障码 P0078-13
P-Code
3-29
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0079-11
P-Code
故障码 P0080-12
P-Code
3-30
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0087-84
P-Code
3. 报故障时油箱是否为无 3.Check whether the oil tank 是 Y 加油后再 Fill oil and test
油状态 is empty in time of fault 测试 again
alarms
否 N 下一步 Next step
7.ECU 控制高压油泵电路 7.The ECU has its high- 是 Y 更换 Replace the ECU
存在异常 pressure oil pump control ECU
circuit abnormal
否 N 下一步 Next step
3-31
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0087-00
P-Code
3. 报故障时油箱是否为无 3.Check whether the oil tank 是 Y 加油后再 Fill oil and test
油状态 is empty in time of fault 测试 again
alarms
否 N 下一步 Next step
7.ECU 控制高压油泵电路 7.The ECU has its high- 是 Y 更换 Replace the ECU
存在异常 pressure oil pump control ECU
circuit abnormal
否 N 下一步 Next step
3-32
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0088-85
P-Code
4.ECU 控制高压油泵电路 4.The ECU has its high- 是 Y 更换 Replace the ECU
存在异常 pressure oil pump control ECU
circuit abnormal
否 N 下一步 Next step
3-33
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0088-00
P-Code
4.ECU 控制高压油泵电路 4.The ECU has its high- 是 Y 更换 Replace the ECU
存在异常 pressure oil pump control ECU
circuit abnormal
否 N 下一步 Next step
3-34
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0097-16
P-Code
进气温度传感器 2 电路电压过低 Intake Air Temperature Sensor 2 (before throttle) Circuit Low
3-35
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0098-17
P-Code
3-36
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0101-23
P-Code
3-37
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0101-24
P-Code
3-38
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0100-13
P-Code
2.HFM 传感器信号引脚端 2.The HFM sensor has its 是 Y 维修线束 Maintenance of the
开路 signal pins open wiring harness
故障码 P0102-16
P-Code
3-39
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0103-17
P-Code
3-40
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0105-2A
P-Code
3-41
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0106-84
P-Code
3-42
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0106-85
P-Code
3-43
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0106-21
P-Code
3-44
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0106-22
P-Code
3-45
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0107-16
P-Code
3-46
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0108-17
P-Code
3-47
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0112-16
P-Code
3-48
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0113-17
P-Code
3-49
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0116-29
P-Code
3-50
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0117-16
P-Code
3-51
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0118-17
P-Code
3-52
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0122-11
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-53
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0123-12
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-54
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0130-29
P-Code
3-55
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0131-16
P-Code
2. 读取并保存故障冻结 2.Read and save the fault freeze 下一步 Next step
帧信息 frame information
4. 起动车辆 , 运行至冷 4.Start the vehicle, let it running 是 Y 下一步 Next step
却液温度达正常值 , 怠 until the coolant temperature
速 . 不得断开氧传感器 has reached the normal value
接插件 , 测量上游氧传 and then have it idling. Have the
感器线束 ECU 端 4 号 oxygen sensor connectors kept
线 (黑色、氧传感器信 connected and measure
号线)和 3 号线 (灰 whether the voltage is changing
色、氧传感器信号地) between 0V and 1V between 否 N 更换氧传 Replace the oxygen
之间的电压是否在 0V Line 4 (black, signal line of the 感器 sensor
- 1V 之间跳变 oxygen sensor) and Line 3
(gray, signal ground of the
oxygen sensor) at the ECU
terminal of the upstream oxygen
sensor wiring harness
3-56
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0132-17
P-Code
3-57
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0132-17
P-Code
3-58
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0133-26
P-Code
3-59
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0137-16
P-Code
2. 读取并保存故障冻结 2.Read and save the fault freeze 下一步 Next step
帧信息 frame information
4. 起动车辆 , 运行至冷 4.Start the vehicle, let it running 是 Y 下一步 Next step
却液温度达正常值 , 怠 until the coolant temperature
速 . 不得断开氧传感器 has reached the normal value
接插件 , 测量下游氧传 and then have it idling. Have the
感器线束 ECU 端 4 号 oxygen sensor connectors kept
线 (黑色、氧传感器信 connected and measure
号线)和 3 号线 (灰 whether the voltage is changing
色、氧传感器信号地) within 0V and 1V between Line 否 N 更换氧传 Replace the oxygen
之间的电压是否在 0V 4 (black, signal line of the 感器 sensor
- 1V 之间跳变 oxygen sensor) and Line 3
(gray, signal ground of the
oxygen sensor) on the
downstream oxygen sensor
wiring harness at the ECU
terminal
3-60
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0138-17
P-Code
3-61
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0138-17
P-Code
故障码 P0135-1E
P-Code
3-62
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0136-29
P-Code
2. 读取并保存故障冻结帧 2.Read and save the fault freeze 下一步 Next step
信息 frame information
6. 起动车辆 , 运行至冷却 6.Start the vehicle, let it running 是 Y 下一步 Next step
液温度达正常值 , 怠速 . 不 until the coolant temperature has
得断开氧传感器接插件 , reached the normal value and
测量下游氧传感器线束 then have it idling. Have the
ECU 端 4 号线 (黑色、 oxygen sensor connectors kept
氧传感器信号线)和 3 号 connected and measure whether 否 N 更换氧传 Replace the
线 (灰色、氧传感器信号 the voltage is changing within 0V 感器 oxygen sensor
地)之间的电压是否在 0V and 1V between Line 4 (black,
- 1V 之间跳变 signal line of the oxygen sensor)
and Line 3 (gray, signal ground
of the oxygen sensor) on the
downstream oxygen sensor
wiring harness at the ECU
terminal
3-63
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0136-29
P-Code
7. 起动车辆 , 运行至冷却 7.Start the vehicle, let it running 是 Y 更换氧传 Replace the
液温度达正常值 , 怠速 . 断 until the coolant temperature has 感器 oxygen sensor
开下游氧传感器接插件 , reached the normal value and
测量氧传感器端 2 号线 then have it idling. Disconnect 否 N 进行其他 Check other
(白色、加热电源地)与 4 the connectors of the 相关部件 related
号线 (黑色、氧传感器信 downstream oxygen sensor and 的检查 components
号线)是否短路 measure whether the oxygen
sensor terminal has its Line 2
(white, heating power ground)
short-circuited Line 4 (black,
signal line of the oxygen sensor)
3-64
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0139-23
P-Code
2. 读取并保存故障冻结 2.Read and save the fault freeze 下一步 Next step
帧信息 frame information
3-65
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0139-23
P-Code
“Penetration through 0.55V-0.65V”means as follows: The voltage has ever been detected beyond or lower than 0.55V-
0.65V
3-66
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0139-24
P-Code
2. 读取并保存故障冻结 2.Read and save the fault freeze 下一步 Next step
帧信息 frame information
3-67
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0139-24
P-Code
“Penetration through 0.55V-0.65V”means as follows: The voltage has ever been detected beyond or lower than 0.55V-
0.65V
3-68
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-29
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-69
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-61
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-70
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-64
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-71
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-92
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-72
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-93
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-73
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0169-94
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-74
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-00
P-Code
2. 读取并保存故障冻 2.Read and save the fault freeze 下一步 Next step
结帧信息 frame information
5. 检查燃油情况,询 5.Check the fuel status and ask 是 Y 更换燃油 Replace the fuel
问客户是否加注指定 the customer whether specified
标号汽油?在加油 gasoline has been filled. Check
后,车辆工作是否有 whether there's something 否 N 下一步 Next step
异常 abnormal with the vehicle after
refueling
3-75
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-00
P-Code
12. 起动车辆,运行 12.Start the vehicle, let it running 是 Y 下一步 Next step
至冷却液温度达正常 until the coolant temperature has
值,怠速,用万用表 reached the normal value and then
红笔头刺穿线束接插 have it idling; force the red probe
头靠 ECU 端 4 号线 of the multimeter into the
绝缘层 (黑色、氧传 insulating layer of Line 4 (black,
感器信号线),黑笔 signal line of the oxygen sensor)
头刺穿线束接插头靠 on the wiring harness connector
ECU 端 3 号线绝缘层 close to the ECU terminal, then 否 N 更换氧传 Replace the oxygen
(灰色、氧传感器信 force the black probe of the 感器 sensor
号地),检查电压是 multimeter into the insulating layer
否在 0V - 1V 之间跳 of Line 3 (gray, signal ground of
变 the oxygen sensor) on the wiring
harness connector close to the
ECU terminal and check whether
the voltage is changing between
0V and 1V
3-76
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-00
P-Code
3-77
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-00
P-Code
2. 读取并保存故障冻 2.Read and save the fault freeze 下一步 Next step
结帧信息 frame information
5. 检查燃油情况,询 5.Check the fuel status and ask 是 Y 更换燃油 Replace the fuel
问客户是否加注指定 the customer whether specified
标号汽油?在加油 gasoline has been filled. Check
后,车辆工作是否有 whether there's something 否 N 下一步 Next step
异常 abnormal with the vehicle after
refueling
3-78
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-00
P-Code
12. 起动车辆,运行 12.Start the vehicle, let it running 是 Y 下一步 Next step
至冷却液温度达正常 until the coolant temperature has
值,怠速,用万用表 reached the normal value and then
红笔头刺穿线束接插 have it idling; force the red probe
头靠 ECU 端 4 号线 of the multimeter into the
绝缘层 (黑色、氧传 insulating layer of Line 4 (black,
感器信号线),黑笔 signal line of the oxygen sensor)
头刺穿线束接插头靠 on the wiring harness connector
ECU 端 3 号线绝缘层 close to the ECU terminal, then 否 N 更换氧传 Replace the oxygen
(灰色、氧传感器信 force the black probe of the 感器 sensor
号地),检查电压是 multimeter into the insulating layer
否在 0V - 1V 之间跳 of Line 3 (gray, signal ground of
变 the oxygen sensor) on the wiring
harness connector close to the
ECU terminal and check whether
the voltage is changing between
0V and 1V
3-79
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-00
P-Code
3-80
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-27
P-Code
2. 读取并保存故障冻 2.Read and save the fault freeze 下一步 Next step
结帧信息 frame information
5. 检查燃油情况,询 5.Check the fuel status and ask 是 Y 更换燃油 Replace the fuel
问客户是否加注指定 the customer whether specified
标号汽油?在加油 gasoline has been filled. Check
后,车辆工作是否有 whether there's something 否 N 下一步 Next step
异常 abnormal with the vehicle after
refueling
3-81
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-27
P-Code
12. 起动车辆,运行 12.Start the vehicle, let it running 是 Y 下一步 Next step
至冷却液温度达正常 until the coolant temperature has
值,怠速,用万用表 reached the normal value and then
红笔头刺穿线束接插 have it idling; force the red probe
头靠 ECU 端 4 号线 of the multimeter into the
绝缘层 (黑色、氧传 insulating layer of Line 4 (black,
感器信号线),黑笔 signal line of the oxygen sensor)
头刺穿线束接插头靠 on the wiring harness connector
ECU 端 3 号线绝缘层 close to the ECU terminal, then 否 N 更换氧传 Replace the oxygen
(灰色、氧传感器信 force the black probe of the 感器 sensor
号地),检查电压是 multimeter into the insulating layer
否在 0V - 1V 之间跳 of Line 3 (gray, signal ground of
变 the oxygen sensor) on the wiring
harness connector close to the
ECU terminal and check whether
the voltage is changing between
0V and 1V
3-82
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0171-27
P-Code
3-83
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-26
P-Code
2. 读取并保存故障冻 2.Read and save the fault freeze 下一步 Next step
结帧信息 frame information
5. 检查燃油情况,询 5.Check the fuel status and ask 是 Y 更换燃油 Replace the fuel
问客户是否加注指定 the customer whether specified
标号汽油?在加油 gasoline has been filled. Check
后,车辆工作是否有 whether there's something 否 N 下一步 Next step
异常 abnormal with the vehicle after
refueling
3-84
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-26
P-Code
12. 起动车辆,运行 12.Start the vehicle, let it running 是 Y 下一步 Next step
至冷却液温度达正常 until the coolant temperature has
值,怠速,用万用表 reached the normal value and then
红笔头刺穿线束接插 have it idling; force the red probe
头靠 ECU 端 4 号线 of the multimeter into the
绝缘层 (黑色、氧传 insulating layer of Line 4 (black,
感器信号线),黑笔 signal line of the oxygen sensor)
头刺穿线束接插头靠 on the wiring harness connector
ECU 端 3 号线绝缘层 close to the ECU terminal, then 否 N 更换氧传 Replace the oxygen
(灰色、氧传感器信 force the black probe of the 感器 sensor
号地),检查电压是 multimeter into the insulating layer
否在 0V - 1V 之间跳 of Line 3 (gray, signal ground of
变 the oxygen sensor) on the wiring
harness connector close to the
ECU terminal and check whether
the voltage is changing between
0V and 1V
3-85
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0172-26
P-Code
3-86
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0192-16
P-Code
故障码 P0191-84
P-Code
3-87
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0193-17
P-Code
3-88
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0201-13
P-Code
故障码 P0202-13
P-Code
3-89
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0203-13
P-Code
故障码 P0204-13
P-Code
3-90
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0219-00
P-Code
1. 是否曾发生过人为提高 1.Check whether the engine 是 Y 清除故障 Clear the fault code
发动机转速超过最高安全 has ever been sped up 码,结束 and that’ s all
转速的情况 artificially beyond the
maximum safe speed 否 N 下一步 Next step
3-91
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0222-11
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-92
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0223-12
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-93
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0234-00
P-Code
故障码 P0236-21
P-Code
3-94
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0236-22
P-Code
3-95
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0236-23
P-Code
3-96
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0236-24
P-Code
3-97
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0237-16
P-Code
3-98
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0238-17
P-Code
3-99
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P023A-13
P-Code
4. 电子水泵电磁阀损坏 4.The electric pump has its 是 Y 更换碳罐 Replace the canister
solenoid valve damaged 阀 valve
故障码 P023B-11
P-Code
3-100
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P023C-12
P-Code
故障码 P0243-13
P-Code
3-101
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0245-11
P-Code
故障码 P0246-12
P-Code
3-102
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0251-11
P-Code
3-103
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0251-13
P-Code
3-104
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0252-12
P-Code
3-105
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0253-11
P-Code
3-106
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0254-12
P-Code
3-107
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P025A-13
P-Code
2. 油泵继电器控制电路开 2.The fuel pump relay has its 是 Y 维修线束 Maintenance of the
路 control circuit open wiring harness
4. 油泵继电器保险熔断或 4.The fuel pump relay has its 是 Y 维修继电 Troubleshoot the
损坏 fuse broken or damaged 器 relay
故障码 P025C-11
P-Code
1. 油泵继电器控制电路对 1.The fuel pump relay has its 是 Y 维修线束 Maintenance of the
地短路 control circuit short-circuited wiring harness
to the ground
否 N 下一步 Next step
3-108
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P025D-12
P-Code
1. 油泵继电器控制电路对 1.The fuel pump relay has its 是 Y 维修线束 Maintenance of the
电源短路 control circuit short-circuited wiring harness
to the power supply
否 N 下一步 Next step
故障码 P0261-11
P-Code
3-109
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0262-12
P-Code
3-110
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0263-00
P-Code
3-111
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0264-11
P-Code
3-112
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0265-12
P-Code
3-113
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0266-00
P-Code
3-114
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0267-11
P-Code
3-115
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0268-12
P-Code
3-116
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0269-00
P-Code
3-117
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0270-11
P-Code
3-118
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0271-12
P-Code
3-119
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0272-00
P-Code
故障码 P0299-00
P-Code
3-120
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0300-00
P-Code
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-121
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0300-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-122
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0301-00
P-Code
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-123
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0301-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-124
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0302-00
P-Code
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-125
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0302-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-126
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0303-00
P-Code
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-127
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0303-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-128
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0304-00
P-Code
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-129
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0304-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-130
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0321-00
P-Code
3-131
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0322-00
P-Code
2. 转速传感器信号端开路 2.The speed sensor has its 是 Y 维修、更 Repair or replace the
signal terminal open 换线束或 wiring harness or
传感器 sensor
3-132
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0325-16
P-Code
4.ECU 端对应的爆震传 4.Check whether the ECU 是 Y 维修或更 Repair or replace the
感器信号端引脚是否对地 corresponding knock 换 ECU ECU
短路,或开路,或对电源 sensor has its signal
短路 terminal pins short or open- 否 N 进行其他 Check other related
circuited to the ground, or 相关部件 components
short-circuited to the power 的检查
supply
3-133
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0325-17
P-Code
3-134
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0327-00
P-Code
3-135
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0327-14
P-Code
3-136
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0328-00
P-Code
3-137
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0328-15
P-Code
3-138
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0341-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
3-139
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0342-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
3-140
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0343-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
3-141
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0366-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
3-142
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0367-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
3-143
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0368-00
P-Code
3. 相位传感器及其信号轮 3.The phase sensor and its 是 Y 重新安装 Install once again
相对安装位置未满足安装 signal gear are not correctly
要求 (如相距过远,未对 installed as required (such
正等) as kept too far apart and not 否 N 下一步 Next step
aligned)
故障码 P0420-00
P-Code
3-144
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0444-13
P-Code
3-145
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0458-11
P-Code
故障码 P0459-12
P-Code
3-146
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0500-22
P-Code
故障码 P0500-23
P-Code
3-147
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0500-26
P-Code
故障码 P0500-2F
P-Code
3-148
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0504-62
P-Code
6. 清除故障码,起动发 6.Clear the fault code, start the 是 Y 进行其他 Check other related
动机到怠速状态,连续 engine, let it idling, step on and 相关部件 components
踩松刹车踏板 25 次, release the brake pedal 的检查
观察故障代码是否再现 continuously for 25 times and
observe whether the fault code 否 N 结束 End
appears again
3-149
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0506-00
P-Code
故障码 P0507-00
P-Code
3-150
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0560-1C
P-Code
3-151
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0562-16
P-Code
3-152
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0563-17
P-Code
3-153
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0601-43
P-Code
下线配置 EEPROM 的 checksum 计算故障 (读取错误) Internal Contr.Module Random Access Memory (RAM)
Error,Special memory failure
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-154
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0601-49
P-Code
下线配置 EEPROM 的 checksum 计算故障 (写入错误) Internal Contr.Module Random Access Memory (RAM)
Error,Internal electronic failure
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-155
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-16
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-156
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-17
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-157
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-29
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
故障码 P0606-42
P-Code
1. 清故障后看是否还会报 1.Clear the fault and see 是 Y 检修 ECU Repair the ECU
出故障 whether any fault is still
reported 否 N 结束 End
3-158
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-44
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
故障码 P0606-45
P-Code
1. 清故障后看是否还会报 1.Clear the fault and see 是 Y 检修 ECU Repair the ECU
出故障 whether any fault is still
reported 否 N 结束 End
3-159
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-47
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-160
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-48
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-161
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-49
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-162
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-63
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-163
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-64
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-164
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-65
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-165
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-91
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-166
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-93
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-167
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0606-97
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-168
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0615-13
P-Code
3-169
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0616-11
P-Code
故障码 P0617-12
P-Code
3-170
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P061F-62
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-171
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P061F-64
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-172
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0634-00
P-Code
1. 冷却风扇驱动芯片过 1.The cooling fan has its 是 Y 维修供电线束 Repair the power
热,检测 ECU 系统供电 driver chip overheated – supply wire harness
是否异常 Check whether the ECU
system power supply is 否 N 下一步 Next step
abnormal
2. 检测是否 ECU 所处环 2.Detect whether the ECU 是 Y 增加散热措施 Take more cooling
境温度偏高 environment temperature 或调整 ECU measures or adjust the
is a little high 在车辆的布置 ECU arrangement in
the vehicle
3. 检测是否 ECU 内部驱 3.Detect whether the ECU 是 Y 更换驱动芯片 Replace the driver chip
动芯片电路异常 internal driver chip circuit is
abnormal 否 N 进行其他相关 Check other related
部件的检查 components
故障码 P0634-49
P-Code
1. 冷却风扇驱动芯片过 1.The cooling fan has its 是 Y 维修供电线束 Repair the power
热,检测 ECU 系统供电 driver chip overheated supply wire harness
是否异常 – Check whether the
ECU system power 否 N 下一步 Next step
supply is abnormal
2. 检测是否 ECU 所处环 2.Detect whether the 是 Y 增加散热措施 Take more cooling
境温度偏高 ECU environment 或调整 ECU measures or adjust the
temperature is a little 在车辆的布置 ECU arrangement in
high the vehicle
3. 检测是否 ECU 内部驱 3.Detect whether the 是 Y 更换驱动芯片 Replace the driver chip
动芯片电路异常 ECU internal driver chip
circuit is abnormal 否 N 进行其他相关 Check other related
部件的检查 components
3-173
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0634-91
P-Code
2. 检测是否 ECU 所处环 2.Detect whether the 是 Y 增加散热措施 Take more cooling
境温度偏高 ECU environment 或调整 ECU measures or adjust the
temperature is a little 在车辆的布置 ECU arrangement in
high the vehicle
3. 检测是否 ECU 内部驱 3.Detect whether the 是 Y 更换驱动芯片 Replace the driver chip
动芯片电路异常 ECU internal driver chip
circuit is abnormal 否 N 进行其他相关 Check other related
部件的检查 components
3-174
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0641-00
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,观 that the throttle self-learning 的检查
察故障代码是否再现 could be completed, and
then start the engine to 否 N 结束 End
observe whether the fault
code appears again
3-175
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0645-13
P-Code
故障码 P0646-11
P-Code
3-176
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0647-12
P-Code
故障码 P0651-00
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,观 that the throttle self-learning 的检查
察故障代码是否再现 could be completed, and
then start the engine to 否 N 结束 End
observe whether the fault
code appears again
3-177
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0686-00
P-Code
3-178
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0690-00
P-Code
1. 主继电器输出电压信 1.The main relay has its 是 Y 更换主继电器 Replace the main relay
号故障,检查主继电器 output voltage signal 后线束、排除 rear wiring harness
后电路是否出现污染、 faulty – Check whether 电路短路故障 and troubleshoot the
老化、短路 the main relay rear circuit short circuit fault
is polluted, aging or short-
circuited 否 N 下一步 Next step
2. 检查 ECU 内部电源 2.Check whether the ECU 是 Y 更换电源芯 Replace the power
芯片是否损坏或电路异 internal power supply chip 片、或排除 supply chip or
常 is damaged or whether ECU 内部电 troubleshoot the short
any circuit is abnormal 源芯片电路短 circuit fault of the
路故障 power supply chip in
the ECU
3. 检查 ECU 内部处理 3.Check whether the ECU 是 Y 排除 ECU 内 Troubleshoot the fault
器电源接口是否异常 internal processor has its 部处理器电源 of abnormal power
power port abnormal 接口异常故障 port of the processor in
the ECU
3-179
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P130B-00
P-Code
1 失火引起断喷油器 , 1.The fuel injector is cut off due 是 Y 到对应缸 Fault code related
检查是否存在对应缸与 to misfire - Check whether there 喷油器相 to the
喷油器相关的故障代码 is any fault code related to the 应故障代 corresponding
corresponding cylinder and fuel 码 cylinder fuel injector
injector
否 N 下一步 Next step
7. 检查火花塞是否异常 7.Check whether the spark plug 是 Y 更换火花 Replace the spark
is abnormal 塞 plug
10. 检查进排气管是否 10. Check whether the intake/ 是 Y 更换或 Replace or repair
异常,例如有堵塞或漏 exhaust pipeline is abnormal, for 修 复故障 the faulty parts
气 example, blockage or leakage 件
3-180
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P130B-00
P-Code
12. 检查燃油压力是否 12. Check whether the fuel 是 Y 更换燃油 Replace the fuel
异常 pressure is abnormal 泵 pump
13. 确认油箱内所加燃 13. Confirm whether the fuel oil 是 Y 放空并清 Drain and clean the
油的油品是否有问题 in the tank has something wrong 洗后油 rear fuel tank and
with its quality 箱,再加 then fill with
入合格燃 qualified fuel
油
3-181
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1386-00
P-Code
故障码 P14A3-00
P-Code
3-182
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P14A6-00
P-Code
1.KL50r 起动反馈信号电 1.Check the KL50r starting 是 Y 检查线束 Check the wiring
路检查,万用表测量电压 feedback signal circuit and harness
use a multimeter to measure
the voltage 否 N 下一步 Next step
3-183
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P14A7-00
P-Code
1.KL50r 起动反馈信号电 1.Check the KL50r starting 是 Y 检查线束 Check the wiring
路检查,万用表测量电压 feedback signal circuit and harness
use a multimeter to measure
the voltage 否 N 下一步 Next step
3-184
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P14A8-00
P-Code
1.KL50r 起动反馈信号电 1.Check the KL50r starting 是 Y 检查线束 Check the wiring
路检查,万用表测量电压 feedback signal circuit and harness
use a multimeter to measure
the voltage 否 N 下一步 Next step
3-185
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P14A9-00
P-Code
1.KL50r 起动反馈信号电 1.Check the KL50r starting 是 Y 检查线束 Check the wiring
路检查,万用表测量电压 feedback signal circuit and harness
use a multimeter to measure
the voltage 否 N 下一步 Next step
3-186
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1523-81
P-Code
1. 检查 SRS 接入 CAN 1.Check whether the wiring 是 Y 检查线束 Check the wiring
总线线束连接是否异常 harness is abnormally harness
connected between the
SRS and the CAN bus 否 N 下一步 Next step
2. 检查 SRS 接入 CAN 2.Check whether the wiring 是 Y 检查电路电压 Check the circuit
总线线束是否短路 harness is short-circuited voltage
between the SRS and the
CAN bus 否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU 电 Exclude the ECU
境周围是否电磁干扰强 system environment is 磁干扰源、或 electromagnetic
烈 subject to strong 屏蔽 ECU 接 interference
electromagnetic 触电磁干扰 sources or prevent
interference the ECU from the
electromagnetic
interference
3-187
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1545-34
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-188
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1545-35
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-189
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1559-78
P-Code
3-190
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1564-00
P-Code
5. 清除故障代码,然后 5.Clear the fault code, turn the 是 Y 下一步 Next step
将点火开关先拧到 OFF, ignition switch to “OFF”at
再置于 ON,等待 1 分钟 first, then to “ON”, wait for 1 否 N 结束 End
完成节气门自学习,观察 minute so that the throttle self-
故障代码是否再现 learning could be completed
and observe whether the fault
code appears again
7. 清除故障代码,然后 7.Clear the fault code, turn the 是 Y 进行其他 Check other related
将点火开关先拧到 OFF, ignition switch to “OFF”at 相关部件 components
再置于 ON,等待 1 分钟 first, then to “ON”, wait for 1 的检查
完成节气门自学习,然后 minute so that the throttle self-
轻踩几下油门,观察故障 learning could be completed, 否 N 结束 End
代码是否再现 and then step on the
accelerator pedal for a few
times to observe whether the
fault code appears again
3-191
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1579-00
P-Code
5. 清除故障代码,然后 5.Clear the fault code, turn the 是 Y 下一步 Next step
将点火开关先拧到 OFF, ignition switch to “OFF” at
再置于 ON,等待 1 分钟 first, then to “ON”, wait for 1 否 N 结束 End
完成节气门自学习,观察 minute so that the throttle self-
故障代码是否再现 learning could be completed
and observe whether the fault
code appears again
7. 清除故障代码,然后 7.Clear the fault code, turn the 是 Y 进行其他 Check other related
将点火开关先拧到 OFF, ignition switch to “OFF” at 相关部件 components
再置于 ON,等待 1 分钟 first, then to “ON”, wait for 1 的检查
完成节气门自学习,然后 minute so that the throttle self-
轻踩几下油门,观察故障 learning could be completed, 否 N 结束 End
代码是否再现 and then step on the
accelerator pedal for a few
times to observe whether the
fault code appears again
3-192
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1615-00
P-Code
4. 如更换过 ECU,防 4.If the ECU has ever been 是 Y 刷新防盗 Refresh the
盗认证码是否错误或未 replaced, check whether the immobilizer
更新 immobilizer authentication code
is incorrect or not updated 否 N 下一步 Next step
3-193
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1616-05
P-Code
4. 如更换过 ECU,防 4.If the ECU has ever been 是 Y 刷新防盗 Refresh the
盗认证码是否错误或未 replaced, check whether the immobilizer
更新 immobilizer authentication code
is incorrect or not updated 否 N 下一步 Next step
3-194
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1617-06
P-Code
4. 如更换过 ECU,防 4.If the ECU has ever been 是 Y 刷新防盗 Refresh the
盗认证码是否错误或未 replaced, check whether the immobilizer
更新 immobilizer authentication code
is incorrect or not updated 否 N 下一步 Next step
3-195
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1618-00
P-Code
4. 如更换过 ECU,防 4.If the ECU has ever been 是 Y 刷新防盗 Refresh the
盗认证码是否错误或未 replaced, check whether the immobilizer
更新 immobilizer authentication code
is incorrect or not updated 否 N 下一步 Next step
3-196
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1619-51
P-Code
4. 如更换过 ECU,防 4.If the ECU has ever been 是 Y 刷新防盗 Refresh the
盗认证码是否错误或未 replaced, check whether the immobilizer
更新 immobilizer authentication code
is incorrect or not updated 否 N 下一步 Next step
3-197
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-21
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-198
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-22
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-199
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-26
P-Code
5. 清除故障代码,然后将 5.Clear the fault code, turn the 是 Y 下一步 Next step
点火开关先拧到 OFF,再 ignition switch to “OFF” at
置于 ON,等待 1 分钟完 first, then to “ON” , wait for 1 否 N 结束 End
成节气门自学习,观察故 minute so that the throttle self-
障代码是否再现 learning could be completed and
observe whether the fault code
appears again
7. 清除故障代码,然后将 7.Clear the fault code, turn the 是 Y 进行其他 Check other
点火开关先拧到 OFF,再 ignition switch to “OFF” at 相关部件 related
置于 ON,等待 1 分钟完 first, then to “ON” , wait for 1 的检查 components
成节气门自学习,然后轻 minute so that the throttle self-
踩几下油门,观察故障代 learning could be completed, 否 N 结束 End
码是否再现 and then step on the accelerator
pedal for a few times to observe
whether the fault code appears
again
3-200
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-28
P-Code
5. 清除故障代码,然后将 5.Clear the fault code, turn the 是 Y 下一步 Next step
点火开关先拧到 OFF,再 ignition switch to “OFF” at
置于 ON,等待 1 分钟完 first, then to “ON” , wait for 1 否 N 结束 End
成节气门自学习,观察故 minute so that the throttle self-
障代码是否再现 learning could be completed
and observe whether the fault
code appears again
7. 清除故障代码,然后将 7.Clear the fault code, turn the 是 Y 进行其他 Check other
点火开关先拧到 OFF,再 ignition switch to “OFF” at 相关部件 related
置于 ON,等待 1 分钟完 first, then to “ON” , wait for 1 的检查 components
成节气门自学习,然后轻 minute so that the throttle self-
踩几下油门,观察故障代 learning could be completed, 否 N 结束 End
码是否再现 and then step on the accelerator
pedal for a few times to observe
whether the fault code appears
again
3-201
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-29
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-202
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-72
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-203
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2101-74
P-Code
4. 清除故障代码,分别 4.Clear the fault code and step 是 Y 下一步 Next step
快踩和慢踩油门踏板数 on the accelerator pedal quickly
次,观察故障代码是否 and slowly respectively for
再现 several times to observe
whether the fault code appears 否 N 结束 End
again
6. 点火开关置于 ON, 6.Turn the ignition switch to 是 Y 进行其他 Check other related
等待 1 分钟完成节气门 “ON”, wait for 1 minute so that 相关部件 components
自学习,然后起动发动 the throttle self-learning could 的检查
机,在空档状态下做若 be completed, and then step on
干次踩油门动作,观察 the accelerator pedal for a few 否 N 结束 End
故障代码是否再现 times when the neutral position
is applied to observe whether
the fault code appears again
3-204
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2106-12
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-205
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2106-13
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-206
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2106-29
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-207
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2106-4B
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-208
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2127-21
P-Code
4. 点火开关置于 ON,清 4.Turn the ignition switch to 是 Y 进行其他 Check other related
除故障代码,然后分别快 “ON” , clear the fault code 相关部件 components
踩和慢踩油门踏板数次, and step on the accelerator 的检查
观察故障代码是否再现 pedal quickly and slowly
respectively for several 否 N 结束 End
times to observe whether
the fault code appears again
3-209
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2128-22
P-Code
4. 点火开关置于 ON,清 4.Turn the ignition switch to 是 Y 进行其他 Check other related
除故障代码,然后分别快 “ON” , clear the fault code 相关部件 components
踩和慢踩油门踏板数次, and step on the accelerator 的检查
观察故障代码是否再现 pedal quickly and slowly
respectively for several 否 N 结束 End
times to observe whether
the fault code appears again
3-210
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2132-21
P-Code
4. 点火开关置于 ON,清 4.Turn the ignition switch to 是 Y 进行其他 Check other related
除故障代码,然后分别快 “ON” , clear the fault code 相关部件 components
踩和慢踩油门踏板数次, and step on the accelerator 的检查
观察故障代码是否再现 pedal quickly and slowly
respectively for several 否 N 结束 End
times to observe whether
the fault code appears again
3-211
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2133-22
P-Code
4. 点火开关置于 ON,清 4.Turn the ignition switch to 是 Y 进行其他 Check other related
除故障代码,然后分别快 “ON” , clear the fault code 相关部件 components
踩和慢踩油门踏板数次, and step on the accelerator 的检查
观察故障代码是否再现 pedal quickly and slowly
respectively for several 否 N 结束 End
times to observe whether
the fault code appears again
3-212
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2135-00
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-213
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2135-29
P-Code
否 N 结束 End
4. 清除故障码,将点火开 4.Clear the fault code, turn 是 Y 进行其他 Check other related
火先拧到 OFF,再置于 the ignition switch to 相关部件 components
ON,等待 1 分钟完成节气 “OFF”at first, then to 的检查
门自学习,然后轻踩几下 “ON” , wait for 1 minute so
油门,观察故障代码是否 that the throttle self-learning 否 N 结束 End
再现 could be completed, and
then step on the accelerator
pedal for a few times to
observe whether the fault
code appears again
3-214
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2140-29
P-Code
4. 点火开关置于 ON,清 4.Turn the ignition switch to 是 Y 进行其他 Check other related
除故障代码,然后分别快 “ON” , clear the fault code 相关部件 components
踩和慢踩油门踏板数次, and step on the accelerator 的检查
观察故障代码是否再现 pedal quickly and slowly
respectively for several 否 N 结束 End
times to observe whether
the fault code appears again
3-215
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2146-00
P-Code
故障码 P2146-14
P-Code
3-216
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2146-15
P-Code
故障码 P2149-00
P-Code
3-217
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2152-00
P-Code
故障码 P2152-14
P-Code
3-218
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2152-15
P-Code
故障码 P2155-00
P-Code
3-219
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2195-24
P-Code
5. 清除故障码,车交还客 5.Clear the fault code, return 是 Y 进行其他 Check other related
户,跟踪故障是否复现 the car to the customer and 相关部件 components
see whether such fault 的检查
appears again
否 N 结束 End
3-220
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2195-25
P-Code
5. 清除故障码,车交还 5.Clear the fault code, return 是 Y 进行其他 Check other related
客户,跟踪故障是否复 the car to the customer and 相关部件 components
现 see whether such fault 的检查
appears again
否 N 结束 End
3-221
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2196-23
P-Code
5. 清除故障码,车交还 5.Clear the fault code, return 是 Y 进行其他 Check other related
客户,跟踪故障是否复 the car to the customer and 相关部件 components
现 see whether such fault 的检查
appears again
否 N 结束 End
3-222
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2196-29
P-Code
5. 清除故障码,车交还 5.Clear the fault code, return 是 Y 进行其他 Check other related
客户,跟踪故障是否复 the car to the customer and 相关部件 components
现 see whether such fault 的检查
appears again
否 N 结束 End
3-223
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2226-23
P-Code
3-224
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2226-24
P-Code
3-225
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2227-21
P-Code
3-226
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2227-22
P-Code
3-227
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2231-00
P-Code
3. 检查线束与 ECU 的接 3. Check whether some pins 是 Y 检修 ECU Repair the ECU or
插件处是否存在 pin 脚短 are short-circuited at the 或线束端 wiring harness
接的异常 connector between the 接头 terminal connector
wiring harness and the ECU
否 N 更换氧传 Replace the oxygen
感器 sensor
3-228
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2243-00
P-Code
3-229
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2251-00
P-Code
3-230
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2261-00
P-Code
故障码 P2414-00
P-Code
3-231
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2626-00
P-Code
5. 清除故障码,起动车 5.Clear the fault code, start the 是 Y 下一步 Next step
辆,运行至冷却液温度 vehicle, let it running until the
达正常值,检查故障是 coolant temperature has 否 N 结束 End
否再次报出 reached the normal value and
then check whether the fault is
reported once again
3-232
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2A01-29
P-Code
2. 读取并保存故障冻结 2.Read and save the fault freeze 下一步 Next step
帧信息 frame information
6. 起动车辆 , 运行至冷 6.Start the vehicle, let it running 是 Y 下一步 Next step
却液温度达正常值 , 怠 until the coolant temperature has
速 . 不得断开氧传感器 reached the normal value and 否 N 更换氧传 Replace the oxygen
接插件 , 测量下游氧传 then have it idling. Have the 感器 sensor
感器线束 ECU 端 4 号 oxygen sensor connectors kept
线 (黑色、氧传感器信 connected and measure whether
号线)和 3 号线 (灰 the voltage is changing within 0V
色、氧传感器信号地) and 1V between Line 4 (black,
之间的电压是否在 0V signal line of the oxygen sensor)
- 1V 之间跳变 and Line 3 (gray, signal ground
of the oxygen sensor) on the
downstream oxygen sensor
wiring harness at the ECU
terminal
3-233
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P2A01-29
P-Code
7. 起动车辆 , 运行至冷 7.Start the vehicle, let it running 是 Y 更换氧传 Replace the oxygen
却液温度达正常值 , 怠 until the coolant temperature has 感器 sensor
速 . 断开下游氧传感器 reached the normal value and
接插件 , 测量氧传感器 then have it idling. Disconnect 否 N 进行其他 Check other related
端 2 号线 (白色、加热 the connectors of the 相关部件 components
电源地)与 4 号线 (黑 downstream oxygen sensor and 的检查
色、氧传感器信号线) measure whether the oxygen
是否短路 sensor terminal has its Line 2
(white, heating power ground)
short-circuited Line 4 (black,
signal line of the oxygen sensor)
3-234
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P300B-00
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-235
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P304B-00
P-Code
3-236
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P304C-00
P-Code
3-237
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P3096-17
P-Code
故障码 P3096-16
P-Code
故障码 P3096-31
P-Code
3-238
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P3096-29
P-Code
1. 该 CJ 芯片内置于 ECU 1.Once this CJ chip built in 是 Y 更换 ECU Replace the ECU
内,一旦出现故障,更换 the ECU has failed, replace
ECU the ECU 否 N 进行其他 Check other related
相关部件 components
的检查
故障码 U0073-88
P-Code
1. 检查 CAN 总线线束连 1.Check whether the CAN 是 Y 检查线束 Check the wiring
接是否异常 bus wiring harness is harness
connected abnormally
否 N 下一步 Next step
2. 检查 CAN 总线线束是 2.Check whether the CAN 是 Y 检查电路 Check the circuit
否短路 bus wiring harness is short- 电压 voltage
circuited
否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU Exclude the ECU
境周围是否电磁干扰强烈 system environment is 电磁干扰 electromagnetic
subject to strong 源、或屏 interference sources
electromagnetic interference 蔽 ECU 接 or prevent the ECU
触电磁干 from the
扰 electromagnetic
interference
3-239
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 U0101-87
P-Code
1. 检查 TCM 接入 CAN 1.Check whether the wiring 是 Y 检查线束 Check the wiring
总线线束连接是否异常 harness is abnormally harness
connected between the TCM
and the CAN bus 否 N 下一步 Next step
2. 检查 TCM 接入 CAN 2.Check whether the wiring 是 Y 检查电路 Check the circuit
总线线束是否短路 harness is short-circuited 电压 voltage
between the TCM and the
CAN bus 否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU Exclude the ECU
境周围是否电磁干扰强烈 system environment is 电磁干扰 electromagnetic
subject to strong 源、或屏 interference sources
electromagnetic interference 蔽 ECU 接 or prevent the ECU
触电磁干 from the
扰 electromagnetic
interference
3-240
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 U0129-87
P-Code
1. 检查 ESP 接入 CAN 总 1.Check whether the wiring 是 Y 检查线束 Check the wiring
线线束连接是否异常 harness is abnormally harness
connected between the ESP
and the CAN bus 否 N 下一步 Next step
2. 检查 ESP 接入 CAN 总 2.Check whether the wiring 是 Y 检查电路 Check the circuit
线线束是否短路 harness is short-circuited 电压 voltage
between the ESP and the
CAN bus 否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU Exclude the ECU
境周围是否电磁干扰强烈 system environment is 电磁干扰 electromagnetic
subject to strong 源、或屏 interference sources
electromagnetic interference 蔽 ECU 接 or prevent the ECU
触电磁干 from the
扰 electromagnetic
interference
3-241
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 U0151-87
P-Code
1. 检查 SRS 接入 CAN 总 1.Check whether the wiring 是 Y 检查线束 Check the wiring
线线束连接是否异常 harness is abnormally harness
connected between the SRS
and the CAN bus 否 N 下一步 Next step
2. 检查 SRS 接入 CAN 总 2.Check whether the wiring 是 Y 检查电路 Check the circuit
线线束是否短路 harness is short-circuited 电压 voltage
between the SRS and the
CAN bus 否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU Exclude the ECU
境周围是否电磁干扰强烈 system environment is 电磁干扰 electromagnetic
subject to strong 源、或屏 interference sources
electromagnetic interference 蔽 ECU 接 or prevent the ECU
触电磁干 from the
扰 electromagnetic
interference
3-242
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0090-12
P-Code
流量控制阀正负极控制电路互短 Diagnosis Fault Check for first Mass Flow Valve Powerstage
for Short Circuit between the High- and Low-Side
3-243
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0601-00
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-244
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0634-48
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-245
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0659-00
P-Code
5. 点火开关置于 ON,等 5.Turn the ignition switch to 是 Y 进行其他 Check other related
待 1 分钟完成节气门自学 “ON” , wait for 1 minute so 相关部件 components
习,然后起动发动机,在 that the throttle self-learning 的检查
空档状态下做若干次踩油 could be completed, and
门动作,观察故障代码是 then step on the accelerator 否 N 结束 End
否再现 pedal for a few times when
the neutral position is applied
to observe whether the fault
code appears again
3-246
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0695-00
P-Code
2.PWM 风扇继电器电路信 2.The PWM fan relay has its 是 Y 维修线束 Maintenance of the
号端对地短路、开路 circuit signal terminal short or wiring harness
open-circuited to the ground
否 N 下一步 Next step
3.PWM 风扇继电器电路故 3.Circuit fault of the PWM fan 是 Y 维修线束 Maintenance of the
障 (保险熔断或损坏) relay (The fuse is blown out wiring harness
or damaged)
否 N 下一步 Next step
4.ECU 对应 PWM 风扇继 4.The ECU corresponding 是 Y 检修 ECU Repair the ECU
电器引脚对地短路、开路 PWM fan relay has its pins
或内部电路损坏 short or open-circuited to the 否 N 进行其他 Check other related
ground or any internal circuit 相关部件 components
is damaged 的检查
3-247
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P0696-00
P-Code
2.PWM 风扇继电器电路信 2.The PWM fan relay has its 是 Y 维修线束 Maintenance of the
号端对地短路、开路 circuit signal terminal short or wiring harness
open-circuited to the ground
否 N 下一步 Next step
3.PWM 风扇继电器电路故 3.Circuit fault of the PWM fan 是 Y 维修线束 Maintenance of the
障 (保险熔断或损坏) relay (The fuse is blown out wiring harness
or damaged)
否 N 下一步 Next step
4.ECU 对应 PWM 风扇继 4.The ECU corresponding 是 Y 检修 ECU Repair the ECU
电器引脚对地短路、开路 PWM fan relay has its pins
或内部电路损坏 short or open-circuited to the 否 N 进行其他 Check other related
ground or any internal circuit 相关部件 components
is damaged 的检查
3-248
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P1683-83
P-Code
SRS 安全气囊 checksum 或 rolling counter 错误 Airbag checksum or rolling counter error
1. 检查 SRS 接入 CAN 1.Check whether the wiring 是 Y 检查线束 Check the wiring
总线线束连接是否异常 harness is abnormally harness
connected between the
SRS and the CAN bus 否 N 下一步 Next step
2. 检查 SRS 接入 CAN 2.Check whether the wiring 是 Y 检查电路电压 Check the circuit
总线线束是否短路 harness is short-circuited voltage
between the SRS and the
CAN bus 否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU 电 Exclude the ECU
境周围是否电磁干扰强 system environment is 磁干扰源、或 electromagnetic
烈 subject to strong 屏蔽 ECU 接 interference
electromagnetic 触电磁干扰 sources or prevent
interference the ECU from the
electromagnetic
interference
3-249
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 P26E6-12
P-Code
3-250
EMS 故障码维修指导 Repair guidance for EMS fault code
故障码 U0111-00
P-Code
1. 检查 CAN 总线线束连 1.Check whether the CAN 是 Y 检查线束 Check the wiring
接是否异常 bus wiring harness is harness
connected abnormally
否 N 下一步 Next step
2. 检查 CAN 总线线束是 2.Check whether the CAN 是 Y 检查电路 Check the circuit
否短路 bus wiring harness is short- 电压 voltage
circuited
否 N 下一步 Next step
3. 检查 ECU 系统所处环 3.Check whether the ECU 是 Y 排除 ECU Exclude the ECU
境周围是否电磁干扰强烈 system environment is 电磁干扰 electromagnetic
subject to strong 源、或屏 interference sources
electromagnetic interference 蔽 ECU 接 or prevent the ECU
触电磁干 from the
扰 electromagnetic
interference
3-251
EMS 故障码维修指导 Repair guidance for EMS fault code
可能原因 1 接插件接插不实或接触不良
2 传感器故障
3 ECM 故障
Possible 1 The connectors contact poorly
causes or are not connected firmly
2 Sensor fault
3 ECM fault
3-252
EMS 故障码维修指导 Repair guidance for EMS fault code
3 ECM fault
3-253
EMS 故障码维修指导 Repair guidance for EMS fault code
可能原因 1 接插件接插不实或接触不良
2 传感器线束故障
3 传感器故障
4 ECM 故障
Possible 1 The connectors contact poorly
causes or are not connected firmly
2 Sensor wiring harness fault
3 Sensor fault
4 ECM fault
3-254
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 The brake vacuum sensor Possible 1 The brake vacuum sensor
causes circuit shorted to ground or causes circuit shorted to ground or
opened or shorted to the power opened or shorted to the power
supply supply
2 Brake vacuum sensor fault 2 Brake vacuum sensor fault
3-255
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 Cruise control circuit open, Possible 1 Cruise control circuit open,
causes short to ground or short to causes short to ground or short to
battery battery
2 Cruise switch fault 2 Cruise switch fault
3-256
EMS 故障码维修指导 Repair guidance for EMS fault code
3-257
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 The electronic thermostat circuit Possible 1 The electronic thermostat circuit
causes is open, short to ground or short causes is open, short to ground or short
to battery to battery
2 Electronic thermostat fault 2 Electronic thermostat fault
3-258
EMS 故障码维修指导 Repair guidance for EMS fault code
2 The system voltage is between Set Clutch travel sensor voltage value is less
condition than 0.2V
10.1v - 16.01V
可能原因 1 离合器行程传感器电路开路,对
设置条件 发动机控制模块检测到电子节温器驱动芯
片温度高于阈值 地短路或对电源短路
3-259
EMS 故障码维修指导 Repair guidance for EMS fault code
3-260
EMS 故障码维修指导 Repair guidance for EMS fault code
3 上述条件持续 5s 3 上述条件持续 5s
Operation 1 The ignition switch is in the ON Operation 1 The ignition switch is in the ON
condition position condition position
2 Battery voltage greater than 7V 2 Battery voltage greater than 7V
设置条件 发动机控制模块检测 EBS 的 LIN 线报文 设置条件 发动机控制模块检测 EBS 的 LIN 线报文
错误或超时 错误或超时
Set The engine control module detects EBS Set The engine control module detects EBS
condition LIN line message errors or timeouts condition LIN line message errors or timeouts
3-261
EMS 故障码维修指导 Repair guidance for EMS fault code
3 上述条件持续 5s 3 上述条件持续 5s
Operation 1 The ignition switch is in the ON Operation 1 The ignition switch is in the ON
condition position condition position
2 Battery voltage greater than 7V 2 Battery voltage greater than 7V
设置条件 发动机控制模块检测 EBS 的 LIN 线报文 设置条件 发动机控制模块检测 EBS 的 LIN 线报文
错误或超时 错误或超时
Set The engine control module detects EBS Set The engine control module detects EBS
condition LIN line message errors or timeouts condition LIN line message errors or timeouts
3-262
EMS 故障码维修指导 Repair guidance for EMS fault code
2 EBS 故障 3 蓄电池故障
3 Battery fault
3-263
EMS 故障码维修指导 Repair guidance for EMS fault code
3 Battery fault
3-264
EMS 故障码维修指导 Repair guidance for EMS fault code
3-265
EMS 故障码维修指导 Repair guidance for EMS fault code
2 Battery voltage greater than 7V Set The engine control module detects the
condition communication fault of the generator
设置条件 发动机控制模块检测到 LIN 总线回读错
误
可能原因 1 发电机故障
3-266
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发电机线束故障 3 发电机线束故障
Possible 1 Generator fault Possible 1 Generator fault
causes causes
2 Engine control module fault 2 Engine control module fault
3-267
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 The hydraulic accumulator Possible 1 The hydraulic accumulator
causes controls the circuit is open causes controls the circuit is open
circuit, short to ground or short circuit, short to ground or short
to battery to battery
2 Hydraulic accumulator fault 2 Hydraulic accumulator fault
3-268
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 The hydraulic accumulator Possible 1 Clutch pump control circuit is
causes controls the circuit is open causes open, short to ground or short to
circuit, short to ground or short battery
to battery
2 Clutch pump fault
2 Hydraulic accumulator fault
3 Engine control module fault
3 Engine control module fault
3-269
EMS 故障码维修指导 Repair guidance for EMS fault code
3 发动机控制模块故障 3 发动机控制模块故障
Possible 1 Clutch pump control circuit is Possible 1 Clutch pump control circuit is
causes open, short to ground or short to causes open, short to ground or short to
battery battery
2 Clutch pump fault 2 Clutch pump fault
3-270
EMS 故障码维修指导 Repair guidance for EMS fault code
3-271
EMS 故障码维修指导 Repair guidance for EMS fault code
3-272
EPS 故障码维修指导 Repair guidance for EPS fault code
EPS 故障码维修指导 Repair guidance for EPS fault code
EPS 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
EPS 故障码维修指导 Repair guidance for EPS fault code
故障码
故障码描述 DTC Description
DTC
2-2
EPS 故障码维修指导 Repair guidance for EPS fault code
故障码
故障码描述 DTC Description
DTC
2-3
EPS 故障码维修指导 Repair guidance for EPS fault code
EPS 故障详解
3 Check the EPS power supply 3 Check the EPS power supply
harness, ground, connector and harness, ground, connector and
fuse fuse
2-4
EPS 故障码维修指导 Repair guidance for EPS fault code
2-5
EPS 故障码维修指导 Repair guidance for EPS fault code
2-6
EPS 故障码维修指导 Repair guidance for EPS fault code
2-7
EPS 故障码维修指导 Repair guidance for EPS fault code
2-8
EPS 故障码维修指导 Repair guidance for EPS fault code
2-9
EPS 故障码维修指导 Repair guidance for EPS fault code
2-10
EPS 故障码维修指导 Repair guidance for EPS fault code
2-11
EPS 故障码维修指导 Repair guidance for EPS fault code
2-12
EPS 故障码维修指导 Repair guidance for EPS fault code
2-13
EPS 故障码维修指导 Repair guidance for EPS fault code
2-14
EPS 故障码维修指导 Repair guidance for EPS fault code
2-15
EPS 故障码维修指导 Repair guidance for EPS fault code
2-16
EPS 故障码维修指导 Repair guidance for EPS fault code
2-17
EPS 故障码维修指导 Repair guidance for EPS fault code
2-18
EPS 故障码维修指导 Repair guidance for EPS fault code
2-19
EPS 故障码维修指导 Repair guidance for EPS fault code
2-20
EPS 故障码维修指导 Repair guidance for EPS fault code
3 It is recommended to conduct
the four wheel alignment first,
then re-calibrate the angle
sensor. If the failure occurs
again, replace the EPS steering
assembly
可能的影响 无自动泊车功能、车道保持功能、末端保
护功能、主动回正功能、 PDC 功能、转
向手感变化
Possible No automatic parking, lane keeping, end
Symptom protection, active return-to-center, PDC
functions, or steering tune change
2-21
EPS 故障码维修指导 Repair guidance for EPS fault code
2-22
EPS 故障码维修指导 Repair guidance for EPS fault code
2-23
EPS 故障码维修指导 Repair guidance for EPS fault code
2-24
EPS 故障码维修指导 Repair guidance for EPS fault code
可能的影响 手感参数未选择
Possible Steering tune parameters are not
Symptom selected
2-25
EPS 故障码维修指导 Repair guidance for EPS fault code
可能的影响 助力减小或无助力
Possible Reduced power assist or no power
Symptom assist
2-26
EPS 故障码维修指导 Repair guidance for EPS fault code
2-27
EPS 故障码维修指导 Repair guidance for EPS fault code
2-28
HVAC 故障码维修指导 Repair guidance for HVAC fault code
HVAC 故障码维修指导 Repair guidance for HVAC fault code
HVAC 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障码
故障码描述 DTC Description
DTC
2-2
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障码
故障码描述 DTC Description
DTC
Rear Temperature door motor short cut to power or
B1193-15 后温度门电机短路到电源或开路负载 open load
B119A-87 后控制面板 LIN 响应错误 Rear Conrtrol Panel LIN Response Error
B119C-87 散热开关 LIN 响应错误 Heat and Vent Switch LIN Response Error
B119D-87 前加热模块 LIN 响应错误 Front Heat Module LIN Response Error
B119F-87 后加热模块 LIN 响应错误 Rear Heat Module LIN Response Error
2-3
HVAC 故障码维修指导 Repair guidance for HVAC fault code
HVAC 故障详解
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-4
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-5
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-6
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-7
HVAC 故障码维修指导 Repair guidance for HVAC fault code
2-8
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 3s
件
Healing Feedback voltage in the normal range
condition continuously more than 3s
2-9
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障诊断码 连续超过 2s 反馈电压高于 4.9V Healing Feedback voltage in the normal range
的判断条件 condition continuously more than 2s
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-10
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-11
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-12
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障诊断码 连续超过 2s 反馈电压高于 4.9V Healing Feedback voltage in the normal range
的判断条件 condition continuously more than 2s
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-13
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-14
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-15
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-16
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-17
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-18
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-19
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-20
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-21
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-22
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-23
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 反馈电压在正常的范围内持续超过 2s
件
Healing Feedback voltage in the normal range
condition continuously more than 2s
2-24
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-25
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
故障治愈条 从 LIN 信号中接收到正常的状态超过 2s Failure Receive the rear blower error error from
件 criteria LIN messgae over 2S
Healing Receive the normal state from LIN 故障治愈条 从 LIN 信号中接收到正常的状态超过 2s
condition messgae over 2S 件
Healing Receive the normal state from LIN
condition messgae over 2S
2-26
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-27
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-28
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-29
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-30
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-31
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-32
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障发生的 - 故障发生的 -
可能原因 可能原因
Possible - Possible -
Cause Cause
2-33
HVAC 故障码维修指导 Repair guidance for HVAC fault code
故障码 B1124-87
DTC
故障码描述 空气净化器颗粒物质传感器错误
DTC Air Purifier C Sensor Error
Description
故障发生的 -
可能原因
Possible -
Cause
检查项目 颗粒传感器故障
Check Particulate Matter fault
Items
2-34
LDW 故障码维修指导 Repair guidance for LDW fault code
LDW 故障码维修指导 Repair guidance for LDW fault code
LDW 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
LDW 故障码维修指导 Repair guidance for LDW fault code
LDW 故障详解
故障发生的 电池 故障发生的 电池
可能原因 可能原因
Possible Battery Possible Battery
Cause Cause
2-2
LDW 故障码维修指导 Repair guidance for LDW fault code
2-3
LDW 故障码维修指导 Repair guidance for LDW fault code
3 从高 / 低压恢复 1s 后 3 从高 / 低压恢复 1s 后
5 网络不在安静模式下 5 网络不在安静模式下
Release 1 1s after communication enable Release 1 1s after communication enable
condition condition
2 supply voltage meet trouble 2 supply voltage meet trouble
diagnostic requirment diagnostic requirment
2-4
LDW 故障码维修指导 Repair guidance for LDW fault code
2-5
LDW 故障码维修指导 Repair guidance for LDW fault code
3 从高 / 低压恢复 1s 后 3 从高 / 低压恢复 1s 后
5 网络不在安静模式下 5 网络不在安静模式下
Release 1 1s after communication enable Release 1 1s after communication enable
condition condition
2 supply voltage meet trouble 2 supply voltage meet trouble
diagnostic requirment diagnostic requirment
2-6
LDW 故障码维修指导 Repair guidance for LDW fault code
2-7
LDW 故障码维修指导 Repair guidance for LDW fault code
故障码 U1D0B-96
DTC
故障码 U1D0B-96 Failure 1 DAS internal 5V/ 3.3V/1.8V/
DTC criteria 1.2V is overvoltage or
undervoltage for 500ms
故障码描述 DAS( 驾驶员辅助系统 ) 内部故障
2 MCU PLL is out-of-range
DTC DAS(Driver Assistence System) Internal
Description Faults 3 MCU abnormally reset
4 MCU flash checksum fault
故障发生的 DAS 电子控制单元
可能原因 5 MCU RAM test fail
Possible DAS 6 EEPROM test fail
Cause
7 Image Process Unit report test
fail in boot diagnostic message
检查项目 检查 DAS 电子控制单元
8 Image Process Unit report
Check DAS system all function disable application fatal error in
Items application message for 2 times
continuously
可能的影响 DAS 系统所有功能功能停止
9 Lost SPI communication with
Possible DAS system all function disable Image Process Unit. (500
Symptom msecs without relevant
message)
故障诊断码 1 不在 Crank 并且 Crank 1s 后
的运行条件 故障治愈条 1 DAS 控制器 5V/3.3V/1.8V/1.2V
2 图像处理器正常上电 件 超过 500ms 正常
Release 1 Not in crank and 1s After crank 2 MCU PLL 在正常范围
condition
2 Image Process Unit is properly 3 MCU 正常复位
powered on
4 MCU Flash 校验正确
故障诊断码 1 DAS 控制器 5V/3.3V/1.8V/1.2V 5 MCU RAM 监测正确
的判断条件 超过 500ms 过压或者欠压
6 EEPROM 监测正确
2 MCU PLL 超出范围
7 图像处理器 Boot 监测正确
3 MCU 异常复位
8 不报图像处理器致命错误
4 MCU Flash 校验出错
9 和图像处理器通信正常
5 MCU RAM 监测错误
Healing 1 DAS internal 5V/ 3.3V/1.8V/
6 EEPROM 监测出错 condition 1.2V are normal for 500ms
7 图像处理器 Boot 监测出错 2 MCU PLL is in-range
8 图像处理器致命错误 3 MCU reset source is normal
9 超过 500ms 和图像处理器失去通 4 MCU flash checksum correct
信
5 MCU RAM test pass
6 EEPROM test pass
7 Image Process Unit report test
pass in boot diagnostic
message
8 Image Process Unit report
application no fatal error in
application message for 100
times continuously
9 No SPI communication error
with Image Process Unit for 2s
continuously
2-8
LDW 故障码维修指导 Repair guidance for LDW fault code
2-9
LDW 故障码维修指导 Repair guidance for LDW fault code
2-10
LDW 故障码维修指导 Repair guidance for LDW fault code
2-11
LDW 故障码维修指导 Repair guidance for LDW fault code
2-12
PTG 故障码维修指导 Repair guidance for PTG fault code
PTG 故障码维修指导 Repair guidance for PTG fault code
PTG 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障码描述 DTC Description
DTC
2-1
PTG 故障码维修指导 Repair guidance for PTG fault code
故障码
故障码描述 DTC Description
DTC
2-2
PTG 故障码维修指导 Repair guidance for PTG fault code
PTG 故障详解
2-3
PTG 故障码维修指导 Repair guidance for PTG fault code
2-4
PTG 故障码维修指导 Repair guidance for PTG fault code
2-5
PTG 故障码维修指导 Repair guidance for PTG fault code
2-6
PTG 故障码维修指导 Repair guidance for PTG fault code
2-7
PTG 故障码维修指导 Repair guidance for PTG fault code
2-8
PTG 故障码维修指导 Repair guidance for PTG fault code
可能的影响 - 可能的影响 -
Possible - Possible -
Symptom Symptom
2-9
PTG 故障码维修指导 Repair guidance for PTG fault code
可能的影响 - 可能的影响 -
Possible - Possible -
Symptom Symptom
2-10
PTG 故障码维修指导 Repair guidance for PTG fault code
2-11
PTG 故障码维修指导 Repair guidance for PTG fault code
2-12
PTG 故障码维修指导 Repair guidance for PTG fault code
2-13
PTG 故障码维修指导 Repair guidance for PTG fault code
Healing Anti-pinch trip resistance is normal: less Failure Voltage feedback satisfies the
condition than 2K or close to 10K Ohm for 5 criteria judgement critia value of STB for 10
monitor cycles monitor cycles
2-14
PTG 故障码维修指导 Repair guidance for PTG fault code
Healing Voltage feedback doesn't satisfy the Healing Voltage feedback doesn't satisfy the
condition judgement critia value of STB for 10 condition judgement critia value of STG for 10
monitor cycles monitor cycles
2-15
PTG 故障码维修指导 Repair guidance for PTG fault code
Healing Voltage feedback doesn't satisfy the Healing Voltage feedback doesn't satisfy the
condition judgement critia value of STG for 10 condition judgement critia value of OL for 10
monitor cycles monitor cycles
2-16
PTG 故障码维修指导 Repair guidance for PTG fault code
2-17
PTG 故障码维修指导 Repair guidance for PTG fault code
2-18
TCU 故障码维修指导 Repair guidance for TCU fault code
TCU 故障码维修指导 Repair guidance for TCU fault code
TCU 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障类型描述 Fault Path Type Description
P-Code
3-1
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码
故障类型描述 Fault Path Type Description
P-Code
P0776-00 压力控制电磁阀 C35R 卡滞关闭 Pressure Control Solenoid C35R Stuck OFF
P0796-00 压力控制电磁阀 C456 卡滞关闭 Pressure Control Solenoid C456 Stuck OFF
3-2
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码
故障类型描述 Fault Path Type Description
P-Code
P2714-00 压力控制电磁阀 CB26 卡滞关闭 Pressure Control Solenoid CB26 Stuck OFF
3-3
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码
故障类型描述 Fault Path Type Description
P-Code
3-4
TCU 故障码维修指导 Repair guidance for TCU fault code
TCU 故障详解
故障码 P0562-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里,测试过程中执行多次发动机停机并重新起 vehicle for about 30 miles, during the test, perform several
动。如果未重现该故障诊断码,将车辆交付顾客。如果重现 engine shut down and restart. If the DTC does not return,
该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查蓄电池电路和电压,如果存在问题,视情况进 step 2
行修理 / 更换。如果未发现蓄电池有问题,目视检查车辆线 Step 2: check the battery circuit and voltage, if there is an
束是否损坏,两侧变速器接插件的针脚是否弯曲 / 损坏,如 issue, repair/replace as appropriate. If no issue is found at
果未发现任何异常,更换并重新刷新机电部件 (仅标定), the battery, check visually the vehicle harness for any
执行变速器自适应程序 damage and the transmission connector on both side for
any bent/damaged pin, if nothing abnormal is found,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
无 None
无 None
发动机运行一段时间,发动 / 运行电压在一段时间内低于变 Engine running for a period of time and crank/run voltage is
速器控制模块输出驱动能力 below Transmission Control Module output driver capability
for a period of time
3-5
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0563-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里,测试过程中执行多次发动机停机并重新起 vehicle for about 30 miles, during the test, perform several
动。如果未重现该故障诊断码,将车辆交付顾客。如果重现 engine shut down and restart. If the DTC does not return,
该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查蓄电池电路和电压,如果存在问题,视情况进 step 2
行修理 / 更换。如果未发现蓄电池有问题,目视检查车辆线 Step 2: check the battery circuit and voltage, if there is an
束是否损坏,两侧变速器接插件的针脚是否弯曲 / 损坏,如 issue, repair/replace as appropriate. If no issue is found at
果未发现任何异常,更换并重新刷新机电部件 (仅标定), the battery, check visually the vehicle harness for any
执行变速器自适应程序 damage and the transmission connector on both side for
any bent/damaged pin, if nothing abnormal is found,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
无 None
无 None
发动机运行一段时间,发动 / 运行电压在一段时间内高于变 Engine running for a period of time and crank/run voltage is
速器控制模块输出驱动能力 above Transmission Control Module output driver
capability for a period of time
3-6
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0601-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2。 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
在控制电磁阀 (带车身和变速器控制模块)总成内处理该 This fault is handled inside the control solenoid (w/body
故障且不牵涉任何外部电路。 程序内所有非零位的总和及 and Transmission Control Module) valve assembly and no
标定存储范围 external circuits are involved.
Summation of all non-zero bits in the program and
calibration memory range
3-7
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0602-00
DTC
刷新机电部件 (仅标定)并执行变速器自适应程序 Program the mechatronic (calibration only) and perform the
transmission adaptation procedure
无 None
一档 1st Gear
3-8
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0603-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
在控制电磁阀 (带车身和变速器控制模块)总成内处理该 This fault is handled inside the control solenoid (w/body
故障且不牵涉任何外部电路 and Transmission Control Module) valve assembly and no
上电期间非易失性存储器的校验和 external circuits are involved.
Checksum of Non Volatile Memory during power-up
3-9
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0604-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2.
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
在控制电磁阀 (带车身和变速器控制模块)总成内处理该 This fault is handled inside the control solenoid (w/body
故障且不牵涉任何外部电路 and Transmission Control Module) valve assembly and no
上电期间进行快速测试,正常时间循环执行期间进行缓慢后 external circuits are involved.
台测试 Fast test during power-up, slow background test during
normal time loop execution
3-10
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P062F-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
在控制电磁阀 (带车身和变速器控制模块)总成内处理该 This fault is handled inside the control solenoid (w/body
故障且不牵涉任何外部电路 and Transmission Control Module) valve assembly and no
停机期间将随机存取存储器故障记录到非易失性副本中 external circuits are involved
log the failure of the Random Access Memory to non-
volatile copy during shutdown
3-11
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0634-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2。 release the vehicle to the customer. If it reappears go to the
步骤 2:执行液位检查程序: step 2
- 如果液位不正确,执行漏液诊断程序,如果未发现任何异 Step 2: Perform the fluid level checking procedure:
常,调节油位,然后清除该故障诊断码,执行钥匙关闭并重 - if the level is not correct, perform the fluid leak diagnosis
新测试车辆大约 48 公里。如果未重现该故障诊断码,将车 procedure, if nothing abnormal is found adjust the oil level,
辆交付顾客。 then clear the code, perform key off, and retest the vehicle
- 如果液位正确,冷起动车辆 (变速器处于环境温度),利 for about 30 miles. If the DTC does not return, release the
用诊断工具对比变速器温度和环境温度,如果两者温差显著 vehicle to the customer.
(>10°C),更换并重新刷新机电部件 (仅标定),执行变速 - if the level is correct, start the vehicle cold (transmission is
器自适应程序,否则检查变速器冷却器系统是否堵塞或损坏 at ambient temperature), compare the transmission
temperature with ambient temperature using the diagnostic
tool, if significant difference between both temperature
(>10°C), replace and reprogram the mechatronic
(calibration only) and perform the transmission adaptation
procedure, otherwise inspect the transmission cooler
system for restrictions or damage
3-12
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0658-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:目视检查车辆线束是否损坏,两侧变速器接插件的 step 2
针脚是否损坏 / 弯曲 / 脱出,如果未发现任何异常,更换并 Step 2: check visually the vehicle harness for any damage
重新刷新机电部件 (仅标定),执行变速器自适应程序 and the transmission connector on both side for any
damaged/bent/pushed back pin, if nothing abnormal is
found, replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-13
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0659-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:目视检查车辆线束是否损坏,两侧变速器接插件的 step 2
针脚是否损坏 / 弯曲 / 脱出,如果未发现任何异常,更换并 Step 2: check visually the vehicle harness for any damage
重新刷新机电部件 (仅标定),执行变速器自适应程序 and the transmission connector on both side for any
damaged/bent/pushed back pin, if nothing abnormal is
found, replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-14
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0667-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-15
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0668-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-16
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0669-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-17
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P06AC-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-18
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P06AD-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-19
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P06AE-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-20
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0711-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-21
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0712-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-22
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0713-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-23
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0716-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查转速传感器螺栓是否正确紧固,如有必要,进 step 2
行修理。如果正确拧紧,更换并重新刷新机电部件 (仅标 Step 2: check if the speed sensor bolt is correctly
定),执行变速器自适应程序 tightened, repair if necessary, if it is correctly bolted,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
无 None
3-24
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0717-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查转速传感器螺栓是否正确紧固,如有必要,进 step 2
行修理。如果正确拧紧,更换并重新刷新机电部件 (仅标 Step 2: check if the speed sensor bolt is correctly
定),执行变速器自适应程序 tightened, repair if necessary, if it is correctly bolted,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
高速:变速器输出转速信号 >= 1350 rpm, High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm.
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
3-25
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0722-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查转速传感器螺栓是否正确紧固,如有必要,进 step 2
行修理。如果正确拧紧,更换并重新刷新机电部件 (仅标 Step 2: check if the speed sensor bolt is correctly
定),执行变速器自适应程序 tightened, repair if necessary, if it is correctly bolted,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
3-26
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0723-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:检查转速传感器螺栓是否正确紧固,如有必要,进 step 2
行修理。如果正确拧紧,更换并重新刷新机电部件 (仅标 Step 2: check if the speed sensor bolt is correctly
定),执行变速器自适应程序 tightened, repair if necessary, if it is correctly bolted,
replace and reprogram the mechatronic (calibration only)
and perform the transmission adaptation procedure
无 None
输出转速大幅减小 (车速高于标定车速时) Large drop in output speed (when the vehicle is above a
calibrated vehicle speed)
3-27
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0741-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:执行液位检查程序: step 2
- 如果液位不正确,执行漏液诊断程序,如果未发现任何异 Step 2: Perform the fluid level checking procedure:
常,调节油位,然后清除该故障诊断码,执行钥匙关闭并重 - if the level is not correct, perform the fluid leak diagnosis
新测试车辆大约 48 公里。如果未重现该故障诊断码,将车 procedure, if nothing abnormal is found adjust the oil level,
辆交付顾客 then clear the code, perform key off, and retest the vehicle
- 如果液位正确,拆下变速器并检查变矩器正后方的输入轴 for about 30 miles. If the DTC does not return, release the
O 形圈,如果损坏或丢失,则进行更换,否则更换并重新刷 vehicle to the customer
新变速器 (仅标定),执行变速器自适应程序 - if the level is correct, remove the transmission and check
the input shaft O ring just located behind the torque
converter, replace it if damaged or missing, otherwise
replace and reprogram the transmission (calibration only)
and perform the transmission adaptation procedure
无 None
3-28
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0742-00
DTC
无 None
3-29
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0751-00
DTC
无 None
变速器换档电磁阀 A 卡滞在关闭位置监视器在换档电磁阀 A The transmission shift solenoid valve A stuck off monitor
(SSA) 卡滞在关闭位置时进行检测 detects when shift solenoid A (SSA) is stuck off
3-30
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0752-00
DTC
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
3-31
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0756-00
DTC
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
变速器换档电磁阀 B 卡滞在关闭位置监视器在换档电磁阀 B The transmission shift solenoid valve B stuck off monitor
(SSB) 卡滞在关闭位置时进行检测 detects when shift solenoid B (SSB) is stuck off
3-32
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0776-00
DTC
压力控制电磁阀 C35R 或离合器系统故障 Pressure Control C35R solenoid or clutch system failure
高速:变速器输出转速信号 >= 1400 rpm,指令四档 High speed: Transmission Output Speed Signal >= 1400
低速:变速器输出转速信号 < 1000 rpm,指令二档,不允 rpm
许升档 Fourth gear commanded
Low speed: Transmission Output Speed Signal < 1000 rpm
Second gear commanded no upshift allowed
变速器压力控制电磁阀 C35R 卡滞在关闭位置监视器在 The transmission pressure control solenoid C35R stuck off
C35R 电磁阀卡滞在关闭位置时进行检测 monitor detects when the C35R solenoid is stuck off
3-33
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0777-00
DTC
压力控制电磁阀 C35R 或离合器系统故障 Pressure Control C35R solenoid or clutch system failure
动态变速器压力控制电磁阀 C35R 卡滞在打开位置监视器在 The dynamic transmission pressure control solenoid C35R
换档期间 C35R 电磁阀卡滞在打开位置时进行检测。应关闭 stuck on monitor detects when the C35R solenoid is stuck
压力控制电磁阀 B 控制的 C35R 离合器时,从三档或五档 on during a shift. The monitor uses the attained gear slip as
换档过程中,监视器将获得的档位滑动用来指示故障 an indication of failure during a shift from 3rd or 5th gear
when the C35R clutch controlled by the Pressure ControlB
solenoid should be off-going
3-34
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0796-00
DTC
压力控制电磁阀 CBR1/C456 或 C456 离合器系统 Pressure Control CBR1/C456 solenoid or C456 clutch
system
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
变速器压力控制电磁阀 C456 卡滞在关闭位置监视器在 The transmission pressure control solenoid C456 stuck off
C456 电磁阀卡滞在关闭位置时进行检测。监视器将获得的 monitor detects when the C456 solenoid is stuck off. The
档位滑动用来指示 C456 电磁阀在四档、五档或六档时的状 monitor uses the attained gear slip as an indication of the
态 state of the C456 solenoid in 4th, 5th, or 6th gear
3-35
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0797-00
DTC
压力控制电磁阀 CBR1/C456 或 C456 离合器系统 Pressure Control CBR1/C456 solenoid or C456 clutch
system
动态变速器压力控制电磁阀 C456 卡滞在打开位置监视器在 The dynamic transmission pressure control solenoid C456
换档期间 C456 电磁阀卡滞在打开位置时进行检测。应关闭 stuck on monitor detects when the C456 solenoid is stuck
压力控制电磁阀 C 控制的 C456 离合器时,从四档、五档或 on during a shift. The monitor uses the attained gear slip as
六档换档过程中,监视器将获得的档位滑动用来指示故障 an indication of failure during a shift from 4th, 5th or 6th
gear when the C456 clutch controlled by the Pressure
ControlC solenoid should be off-going
3-36
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0815-00
DTC
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
故障码 P0816-00
DTC
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
无 None
3-37
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0826-00
DTC
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
无 None
升档和降档开关电路诊断监视器检测升档 / 降档开关电路电 The up and down shift switch circuit diagnostic monitor
压是否错误,该状态持续一段时间 detects if the upshift/downshift switch circuit is at an illegal
voltage for an continuous amount of time
3-38
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0842-00
DTC
变速器液压 C35R 电路电压过低 Transmission Fluid Pressure C35R Circuit Low Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C35R 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the C35R clutch regulator
态。监视器评估 C35R 离合器调节阀的状态变化,压力开关 valve as an indication of the state of the pressure switch.
故障时压力开关的状态不变 The monitor evaluates a change in the state of the C35R
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-39
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0843-00
DTC
变速器液压 C35R 电路电压过高 Transmission Fluid Pressure C35R Circuit High Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C35R 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the C35R clutch regulator
态。监视器评估 C35R 离合器调节阀的状态变化,压力开关 valve as an indication of the state of the pressure switch.
故障时压力开关的状态不变 The monitor evaluates a change in the state of the C35R
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-40
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0872-00
DTC
变速器液压 CB26 电路电压过低 Transmission Fluid Pressure CB26 Circuit Low Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 CB26 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the CB26 clutch regulator
态。监视器评估 CB26 离合器调节阀的状态变化,压力开关 valve as an indication of the state of the pressure switch.
故障时压力开关的状态不变 The monitor evaluates a change in the state of the CB26
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-41
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0873-00
DTC
变速器液压 CB26 电路电压过高 Transmission Fluid Pressure CB26 Circuit High Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 CB26 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the CB26 clutch regulator
态。监视器评估 CB26 离合器调节阀的状态变化,压力开关 valve as an indication of the state of the pressure switch.
故障时压力开关的状态不变 The monitor evaluates a change in the state of the CB26
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-42
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0877-00
DTC
变速器液压 C1234 电路电压过低 Transmission Fluid Pressure C1234 Circuit Low Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C1234 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the C1234 clutch regulator
态。监视器评估 C1234 离合器调节阀的状态变化,压力开 valve as an indication of the state of the pressure switch.
关故障时压力开关的状态不变 The monitor evaluates a change in the state of the C1234
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-43
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0878-00
DTC
变速器液压 C1234 电路电压过高 Transmission Fluid Pressure C1234 Circuit High Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C1234 离合器调节阀的状态用来指示压力开关状 The monitor uses the state of the C1234 clutch regulator
态。监视器评估 C1234 离合器调节阀的状态变化,压力开 valve as an indication of the state of the pressure switch.
关故障时压力开关的状态不变 The monitor evaluates a change in the state of the C1234
clutch regulator valve, without a change in state of the
pressure switch as a failure of the pressure switch
3-44
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0961-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在合理性故障状况;从而导致管路压力不同于指令管路压 feedback information to determine that the rationality fault
condition exists; which results in line pressure being
different than the commanded line pressure
3-45
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0962-00
DTC
压力控制电磁阀 A 控制电路电压过低 (线压力) Pressure Control Solenoid A Control Circuit Low Voltage
(Line Pressure)
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致管路压力低 feedback information to determine that the short to ground
condition exists; resulting in low line pressure
3-46
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0963-00
DTC
压力控制电磁阀 A 控制电路电压过高 (线压力) Pressure Control Solenoid A Control Circuit High Voltage
(Line Pressure)
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致管路压力高 feedback information to determine that the short to voltage/
open circuit condition exists; resulting in high line pressure
3-47
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0965-00
DTC
压力控制电磁阀 C35R 控制电路合理性测试 Pressure Control Solenoid C35R Control Circuit Rationality
Test
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-48
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0966-00
DTC
压力控制电磁阀 C35R 控制电路电压过低 Pressure Control Solenoid C35R Control Circuit Low
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致 C35R 离合器压力低 feedback information to determine that the short to ground
condition exists; resulting in low C35R clutch pressure
3-49
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0967-00
DTC
压力控制电磁阀 C35R 控制电路电压过高 Pressure Control Solenoid C35R Control Circuit High
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致 C35R 离合器压力高 feedback information to determine that the short to voltage/
open circuit condition exists; resulting in high pressure
flowing to the C35R clutch
3-50
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0969-00
DTC
压力控制电磁阀 C456 控制电路合理性测试 Pressure Control Solenoid C456 Control Circuit Rationality
Test
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-51
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0970-00
DTC
压力控制电磁阀 C456 控制电路电压过低 Pressure Control Solenoid C456 Control Circuit Low
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致 C456 离合器压力低 feedback information to determine that the short to ground
condition exists; resulting in low pressure flowing to the
C456 clutch
3-52
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0971-00
DTC
压力控制电磁阀 C456 控制电路电压过高 Pressure Control Solenoid C456 Control Circuit High
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致 C456 离合器压力高 feedback information to determine that the short to voltage/
open circuit condition exists; resulting in high pressure
flowing to the C456 clutch
3-53
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0973-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致换档电磁阀 A 处于阀门打开位 feedback information to determine that the short to ground
置 condition exists; resulting in an open valve position for the
shift solenoid A
3-54
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0974-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 HWIO 诊断反馈信息确定存 The DTC uses hardware input/output HWIO diagnostic
在对电压短路 / 断路状况;从而导致换档电磁阀 A 处于阀门 feedback information to determine that the short to voltage/
关闭位置 open circuit condition exists; resulting in a closed valve
position for the shift solenoid A
3-55
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0976-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致换档电磁阀 B 处于阀门打开位 feedback information to determine that the short to ground
置 condition exists; resulting in an open valve position for the
shift solenoid B
3-56
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0977-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致换档电磁阀 B 处于阀 feedback information to determine that the short to voltage/
门关闭位置 open condition exists; resulting in a closed valve position
for the shift solenoid B
3-57
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0989-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C456/CBR1 离合器调节阀的状态用来指示压力开 The monitor uses the state of the C456/CBR1 clutch
关状态。监视器评估 C456/CBR1 离合器调节阀的状态变 regulator valve as an indication of the state of the pressure
化,压力开关故障时压力开关的状态不变 switch. The monitor evaluates a change in the state of the
C456/CBR1 clutch regulator valve, without a change in
state of the pressure switch as a failure of the pressure
switch
3-58
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P0990-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
监视器将 C456/CBR1 离合器调节阀的状态用来指示压力开 The monitor uses the state of the C456/CBR1 clutch
关状态。监视器评估 C456/CBR1 离合器调节阀的状态变 regulator valve as an indication of the state of the pressure
化,压力开关故障时压力开关的状态不变 switch. The monitor evaluates a change in the state of the
C456/CBR1 clutch regulator valve, without a change in
state of the pressure switch as a failure of the pressure
switch
3-59
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P1761-00
DTC
变速器手动模式升档 / 降档开关信号电路,滚动数 Tap Up/Tap Down Switch Signal Circuit, Rolling Count
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
取消模式开关 Cancel mode switches
无 None
3-60
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P182E-00
DTC
内部模式开关电路 A 低,报告为内部模式开关 - 无效范围 Internal Mode Switch Circuit A Low, Reported as Internal
Mode Switch - Invalid Range
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
P182E 内部模式开关 (IMS) 诊断监视器检测来自轴位置开关 The P182E Internal Mode Switch (IMS) diagnostic monitor
的错误信号。变速器控制模块中有四个输入信号参数,指示 detects an improper signal from the shaft position switch.
选择的变速器档位范围 (信号 A、 B、 C 和 P) There are four input signal parameters into the
Transmission Control Modul which indicate which
transmission gear range is selected (Signal A, B, C, and P)
3-61
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P182E-00
DTC
内部模式开关电路 A 低,报告为内部模式开关 - 无效范围 Internal Mode Switch Circuit A Low, Reported as Internal
Mode Switch - Invalid Range
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
P182E 内部模式开关 (IMS) 诊断监视器检测来自轴位置开关 The P182E Internal Mode Switch (IMS) diagnostic monitor
的错误信号。变速器控制模块中有四个输入信号参数,指示 detects an improper signal from the shaft position switch.
选择的变速器档位范围 (信号 A、 B、 C 和 P) There are four input signal parameters into the
Transmission Control Modul which indicate which
transmission gear range is selected (Signal A, B, C, and P)
3-62
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P1876-00
DTC
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
无 None
3-63
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P1915-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:目视检查车辆线束是否损坏,两侧变速器接插件的 step 2
针脚是否损坏 / 弯曲 / 脱出,如果未发现任何异常,更换并 Step 2: check visually the vehicle harness for any damage
重新刷新机电部件 (仅标定),执行变速器自适应程序 and the transmission connector on both side for any
damaged/bent/pushed back pin, if nothing abnormal is
found, replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-64
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2714-00
DTC
压力控制电磁阀 CB26 或离合器系统故障 Pressure Control CB26 solenoid or clutch system failure
变速器压力控制电磁阀 CB26 卡滞在关闭位置监视器在 The transmission pressure control solenoid CB26 stuck off
CB26 电磁阀卡滞在关闭位置时进行检测。监视器将获得的 monitor detects when the CB26 solenoid is stuck off. The
档位滑动用来指示 CB26 电磁阀在二档或六档时的状态 monitor uses the attained gear slip as an indication of the
state of the CB26 solenoid in either 2nd or 6th gear
3-65
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2715-00
DTC
压力控制电磁阀 CB26 或离合器系统故障 Pressure Control CB26 solenoid or clutch system failure
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
动态变速器压力控制电磁阀 CB26 卡滞在打开位置监视器在 The dynamic transmission pressure control solenoid CB26
换档期间 CB26 电磁阀卡滞在打开位置时进行检测。监视器 stuck on monitor detects when the CB26 solenoid is stuck
将获得的档位滑动用来指示应关闭压力控制电磁阀 D 控制 on during a shift. The monitor uses the attained gear slip as
的 CB26 离合器时从二档或六档换档过程中的故障 an indication of failure during a shift from 2nd or 6th gear
when the CB26 clutch controlled by the Pressure ControlD
solenoid should be off-going
3-66
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2719-00
DTC
压力控制电磁阀 CB26 控制电路合理性测试 Pressure Control Solenoid CB26 Control Circuit Rationality
Test
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-67
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2720-00
DTC
压力控制电磁阀 CB26 控制电路电压过低 Pressure Control Solenoid CB26 Control Circuit Low
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致 CB26 离合器压力低 feedback information to determine that the short to ground
condition exists; resulting in low pressure flowing to the
CB26 clutch
3-68
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2721-00
DTC
压力控制电磁阀 CB26 控制电路电压过高 Pressure Control Solenoid CB26 Control Circuit High
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致 CB26 离合器压力高 feedback information to determine that the short to voltage/
open condition exists; resulting in high pressure flowing to
the CB26 clutch
3-69
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2723-00
DTC
压力控制电磁阀 C1234 或离合器系统故障 Pressure Control C1234 solenoid or clutch system failure
变速器压力控制电磁阀 C1234 卡滞在关闭位置监视器在 The transmission pressure control solenoid C1234 stuck
C1234 电磁阀卡滞在关闭位置时进行检测。监视器将获得的 off monitor detects when the C1234 solenoid is stuck off.
档位滑动用来指示 C1234 电磁阀在一档锁止、二档、三档 The monitor uses the attained gear slip as an indication of
或四档时的状态 the state of the C1234 solenoid in 1st locked, 2nd,3rd, or
4th gear
3-70
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2724-00
DTC
压力控制电磁阀 C1234 或离合器系统故障 Pressure Control C1234 solenoid or clutch system failure
高速:变速器输出转速信号 >= 1400 rpm High speed: Transmission Output Speed Signal >= 1400
指令四档 rpm
低速:变速器输出转速信号 < 1000 rpm,指令二档,不允 Fourth gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1000 rpm
Second gear commanded no upshift allowed
3-71
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2728-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2。 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-72
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2729-00
DTC
压力控制电磁阀 C1234 控制电路电压过低 Pressure Control Solenoid C1234 Control Circuit Low
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
高速:变速器输出转速信号 >= 1350 rpm High speed: Transmission Output Speed Signal >= 1350
空档,未指令离合器档位 rpm
低速:变速器输出转速信号 < 1350 rpm,指令二档,不允 Neutral No Clutch gear commanded
许升档 Low speed: Transmission Output Speed Signal < 1350 rpm
Second gear commanded no upshift allowed
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对地短路状况;从而导致 C1234 离合器压力低 feedback information to determine that the short to ground
condition exists; resulting in low pressure flowing to the
C1234 clutch
3-73
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2730-00
DTC
压力控制电磁阀 C1234 控制电路电压过高 Pressure Control Solenoid C1234 Control Circuit High
Voltage
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
故障诊断码使用硬件输入 / 输出 (HWIO) 诊断反馈信息确定 The DTC uses hardware input/output (HWIO) diagnostic
存在对电压短路 / 断路状况;从而导致 C1234 离合器压力 feedback information to determine that the short to voltage/
高 open condition exists; resulting in high pressure flowing to
the C1234 clutch
3-74
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2762-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
无 None
3-75
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2763-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-76
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 P2764-00
DTC
步骤 1:清除该故障诊断码,执行钥匙关闭并重新测试车辆 Step 1: clear the code, perform key off, and retest the
大约 48 公里。如果未重现该故障诊断码,将车辆交付顾 vehicle for about 30 miles. If the DTC does not return,
客。如果重现该故障诊断码,转至步骤 2。 release the vehicle to the customer. If it reappears go to the
步骤 2:更换并重新刷新机电部件 (仅标定),执行变速器 step 2
自适应程序 Step 2: replace and reprogram the mechatronic (calibration
only) and perform the transmission adaptation procedure
无 None
3-77
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 U0073-00
DTC
3-78
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 U0100-00
DTC
3-79
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 U0102-00
DTC
无 None
该监视器旨在于变速器控制模块不再接收 TCCM 定期信息 This monitor is designed to detect when the Transmission
时进行检测 Control Module no longer receives the periodic messages
from the TCCM
故障码 U0121-00
DTC
无 None
无 None
该监视器旨在于变速器控制模块不再接收 ABSM 定期信息 This monitor is designed to detect when the Transmission
时进行检测 Control Module no longer receives the periodic messages
from the ABSM
3-80
TCU 故障码维修指导 Repair guidance for TCU fault code
故障码 U0140-00
DTC
禁止升档 / 降档 / 手动升档 / 手动降档 Inhibit Tap Up/Tap Down /Manual Up/Manual Down
取消模式开关 Cancel mode switches
无 None
该监视器旨在于变速器控制模块不再接收 BCM 定期信息时 This monitor is designed to detect when the Transmission
进行检测 Control Module no longer receives the periodic messages
from the BCM
故障码 U0155-00
DTC
无 None
无 None
该监视器旨在于变速器控制模块不再接收 IPKM 定期信息时 This monitor is designed to detect when the Transmission
进行检测 Control Module no longer receives the periodic messages
from the IPKM
3-81
TCU 故障码维修指导 Repair guidance for TCU fault code
3-82
TPMS 故障码维修指导 Repair guidance for TPMS fault code
TPMS 故障码维修指导 Repair guidance for TPMS fault code
TPMS 故障码及故障类型描述汇总
Description on the fault code and failure type
故障码
故障类型描述 Fault Path Type Description
P-Code
4-1
TPMS 故障码维修指导 Repair guidance for TPMS fault code
故障码
故障类型描述 Fault Path Type Description
P-Code
4-2
TPMS 故障码维修指导 Repair guidance for TPMS fault code
TPMS 故障详解
故障码 B2004-16
故障码 B2002-16 DTC
DTC
故障码描述 右后传感器电压低
故障码描述 左前传感器电压低
DTC RR sensor battery voltage low
DTC FL sensor battery voltage low Description
Description
故障发生的 右后传感器电压低于 2.1V
故障发生的 左前传感器电压低于 2.1V 可能原因
可能原因
Possible RR sensor battery voltage is lower than
Possible FL sensor battery voltage is lower than Cause 2.1V
Cause 2.1V
检查项目 读取右后传感器电压值
检查项目 读取左前传感器电压值
Check Items Read the RR sensor battery voltage
Check Items Read the FL sensor battery voltage
可能的影响 右后传感器无法正常发射数据
可能的影响 左前传感器无法正常发射数据
Possible RR sensor can't send data normally
Possible FL sensor can't send data normally Symptom
Symptom
4-3
TPMS 故障码维修指导 Repair guidance for TPMS fault code
Check Items Read the RL sensor battery voltage Possible 1 Data normally
Cause
可能的影响 左后传感器无法正常发射数据 2 ECU can't work normally
检查项目 1 查看右前传感器是否有损坏
2 查看控制器是否损坏
Check Items 1 Check whether the FL sensor
isfailure
2 Check whether the ECU is
failure
可能的影响 控制器无法正常接收数据
Possible ECU can't send data normally
Symptom
4-4
TPMS 故障码维修指导 Repair guidance for TPMS fault code
4-5
TPMS 故障码维修指导 Repair guidance for TPMS fault code
4-6
TPMS 故障码维修指导 Repair guidance for TPMS fault code
3 Check whether the ECU can 3 Check whether the ECU can
send and receive data send and receive data
4-7
TPMS 故障码维修指导 Repair guidance for TPMS fault code
故障发生的 左前轮胎漏气
故障码 P2001-16 可能原因
DTC
Possible FL Tire leakage
故障码描述 控制器电压低 Cause
检查项目 检查控制器供电电压
Check Items Check ECU battery voltage
4-8
TPMS 故障码维修指导 Repair guidance for TPMS fault code
DTC Lost communication with HAVC DTC FR Tire Fast Pressure Loss
Description Description
2 检查 HAVC 工作是否正常
3 检查控制器是否能正常收发数
据 故障码 B100C-27
Check Items DTC
1 The CAN net is normal
2 Check whether the HAVC is in 故障码描述 右后快速漏气
normal condition DTC RR Tire Fast Pressure Loss
3 Check whether the ECU can Description
send and receive data
故障发生的 右后轮胎漏气
可能的影响 环境温度错误 可能原因
检查项目 检查轮胎压力
Check Items Check Tire Pressure
可能的影响 漏气、低压报警
Possible leakage 、 low Pressure Alarm
Symptom
4-9
TPMS 故障码维修指导 Repair guidance for TPMS fault code
4-10
TPMS 故障码维修指导 Repair guidance for TPMS fault code
4-11
TPMS 故障码维修指导 Repair guidance for TPMS fault code
故障码 B1015-98
DTC
故障码描述 左后高温
DTC RL Tire High Temperature
Description
故障发生的 左后轮胎高温
可能原因
Possible RL Tire temprture
Cause
检查项目 检查轮胎温度
Check Items Check Tire temprture
可能的影响 高温报警
Possible High temprture Alarm
Symptom
4-12