SERVICE MANUAL
FOR
CITIZEN’S BAND TRANSCEIVER
HANDHELD TYPE
6 CHANNELS 3 WATTGENERAL ‘TRANSMITTER
Recalving System ‘cxytal controled superetaroayne Final Power Input watt
Channels ‘Any 8 in CB band. Supplied with chanel AF Power Output 15 watt
1S crptal ('A" potion) Modulation 901008
Frequency Coverage 26.865 to 27.405 MHz with appropriate Emission Type a
crystals Frequency Tolerance 2.00596
Power Requirements $2128 V 0G, 8” AA” Cote with 2 ‘Antenna impedance 50 ohms (80-239 type roptacl)
dummy batteries or 10 NiCd batoris, Curent Drain 1500 mA with "00% modula
negative ground oniy AMC Range
‘Speaker Dynamic type (8 Ohms)
‘Semiconductors Siransistors, 10 diodes and 2 termistors ca
Aree Lhaedcteted dit Senativity 0.5, nV for 10.68 (S+NYN
Seletsity 35 6B at 10 Kee
‘Adjacent Channel election 40.68
‘audio Power (0.7 W 10% at 1000 He
‘Signs-to-nolse Ratio 45.08
Intermediate Frequency 455 ke
SSqueieh Sonaltty Threshold less than 07 pv
Current Oran 22 mA with minimum output
SCREW BATTERY COVER BATTERY COMPARTMENT —_ BATTERY INSTALLATION
‘The battery compartment in the rear
Cover wil take 10 battery coll It dry
batteries are used 8 colls are required.
‘The remaining two subcomparments
bridged over with the enclosed two metal
“dummy batteries" ‘When rechargeable
batteries of NiGd-type are used tne 10
‘cells will fil the battery. compartment
‘without any dummy batteries
ay, :
Detach the battery coveratterloosen-
Ing the screw atthe lower part of the
Install the eight battery cells with two
‘dummy batteries (or the ten NiGa-
fella). Put the cals Into place in the
‘omparment as shown.
CRYSTAL INSTALLATION
You can operate on any sixof the CB radio
Channels by installing suitable crystals in
‘each internal crystal socket. Crystal
Sockets are located inside the case, on
the printed circuit board. Remove the
Berew at the back ofthe cabinet and take
Off the back cover Transmiting crystals
faye plugged into sockets marked TX and
feeiving erystale into sockets AX. Be
Careful to plug erystals incorrect sockets,
{inthe sockets for enanne! A there should
bbe one TX and one RXcrysialforthesame
hanno! ete. The receiving crystal is In
most cases marked with @ frequency
‘whieh fs 0.455 MH Towertnan the trans
mitting frequency for the same chan
HANNEL,
UNIVERSAL CONNECTOR
‘The S:pole DIN standard connector in
the bottom of the cabinet sults nehandic
UUnivereal Cassete, which automatically
‘witches between the different functions
iWotner connections are made, please
ote the fallowing:
1. Earphone or external loudspeaker:
Connect to pins 2and3,Aisoconnect
pin opin 4 to make the bateriesto
‘supply power.
2. External power supply: Positive lead
ta pin 4 negative to pin 2. Also
‘connect pin Sto pin Sto got the bul
in iguaspeaker to function.
3, Recharge of iC cells: A battery
Charger of currentiimtting type for
SO mA at 45 Vis connected withthe
Dostve lead opin d and the negative
fo pin2.GENERAL ALIGNMENT
Test equipment required
1
2
3,
RF standard signal generator (S.S.G.) 7
AF signal generator 8.
V.T.V.M. (AC) 9.
V.T.V.M. (DC) 10.
Oscilloscope u
Monitor receiver 12,
ALIGNMENT POSITION
Frequency counter
DC power supply
500 mA DC ammeter
8 2 dummy load
RF power meter with 50 2 dummy load
Radiation (Field strength) meter
BLOCK DIAGRAM
ANT. JACK, on aa ca
D1, D2
a iid Mix IF
age
Rx xTAL[ 05
Rx osc
i
SPKR/MIC
rextat_ [ais ore
De
Txose B