Professional Documents
Culture Documents
SSAB PRODUCTS
FOR OFFSHORE AND
MARINE INDUSTRIES
1
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
INTRODUCTION
SSAB produces special construction steel that conforms to most international
and national standards, as well as steel for offshore and shipping that conforms
to rules from international classification societies. Strenx® performance steel is
our top-of-the-line construction steel, combining high strength with excellent
toughness and weldability. SSAB also produces the well-known Hardox® wear
plate, Armox® protection plate and Toolox® engineering and tool steel.
SSAB Offshore
and Marine grades
SSAB merged with Ruukki in 2014, which allowed for a complete
range of standardized shipping plate, all the way up to the latest
developments of Strenx® performance steel grades with high
yield strength, toughness, weldability and formability.
The Offshore and Marine “OM” versions of Strenx® performance
steel deliver the consistency, tolerances and properties of
the highest quality structural steels in combination with the
classification and branch standards of the Offshore and Marine
segment.
SSAB was one of the first steel manufacturers to develop
advanced and ultra high strength steel grades. Over the years,
we have fine-tuned them to give optimal performance when it
comes to weldability, toughness, formability and crack resistance.
2
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
4 5
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
Strenx 620 OME 620 4.8–1303 69J [-40] L 15 –30mm 0,38/0,57 DNV-GL NV E6202
69J [-40] T (30)–100 mm 0,39/0,58 DNV-GL VL E6202
(100)–130 mm 0,41/0,67 LR EH622
ABS EQ70
Strenx 700E 700 4–53 69J [-40] T 14 –5mm 0,34/0,48 EN 10025-6
650 (53)–100 (5)–30 mm 0,32/0,49 S 690 QL
650 (100)–160 (30)–60 mm 0,36/0,52
(60)–100 mm 0,39/0,58
(100)–130 mm 0,41/0,67
(130)–160 mm 0,43/0,73
Strenx 700 OME 690 4,8 – 130 69J [-40] L 14 –30mm 0,38/0,57 DNV-GL NV E6902
69J [-40] T (30)–100 mm 0,39/0,58 DNV-GL VL E6902
(100)–130 mm 0,41/0,67 LR EH692
ABS EQ70
Strenx 700F 700 4– 53 27J [-60] T 14 –30 mm 0,38/0,57 EN 10025-6
650 (53)–100 (30)–100 mm 0,39/0,58 S 690 QL1
650 (100)–130 (100)–130 mm 0,41/0,67
Strenx 900E 900 4–53 27J [-40] T 12 4–80 mm 0,39/0,58 EN 10025-6
830 (53)–100 (80)–100 mm 0,41/0,63 S 890 QL
Strenx 900F 900 4–53 27J [-60] T 12 4–80 mm 0,39/0,58 EN 10025-6
830 (53)–80 (80)–100 mm 0,41/0,63 S 890 QL1
Strenx 960E 960 4–53 40J [-40] T 12 4–(35) mm 0,38/0,58 EN 10025-6
850 (53)–100 10 35–100 mm 0,41/0,67 S 960 QL
Strenx 1100E 1100 4–(5) 27J [-40] T 8 – (5) mm 0,37/0,57
(5)–40.0 10 5–(8) mm 0,38/0,58
8–(15) mm 0,39/0,62
15–(40) 0,42/0,73
Strenx 1100F 1100 4–(5) 27J [-60] T 8 5–(8) mm 0,40/0,70
(5)–40.0 10 8–(15) mm 0,40/0,70
15–(40) mm 0,42/0,73
Strenx 1300E 1300 4–10 27J [-40] T 8 4–10 mm 0,43/0,67
Strenx 1300F 1300 4–10 27J [-60] T 8 4–10 mm 0,43/0,67
1) CET = C + (Mn+Mo)/10 + (Cr + Cu)/20 + (Ni)/40 CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15
2) Max thickness 80 mm for DNV-GL and LR
6 7
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
PERFORMANCE
Safety boat davits
Winches and deck equipment
STEEL APPLICATIONS
Dredging
Ramps, decks and cargo hatches
Gears and racks
8 9
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
SSAB OFFSHORE AND MARINE PLATE MEETING SSAB OFFSHORE AND MARINE PLATE MEETING
ABS, DNV-GL AND LR STANDARDS RMRS, BV AND RINA STANDARDS
Main Group ABS American Bureau DNV-GL Det Norske Veritas Germ. Lloyds Register Thickness Main Group RMRS Russian Maritime Register BV Bureau Veritas RINA
Class of shipping Lloyds Class of Shipping
Yield Strength Grade Interval, mm Grade Interval [Steel Grade Interval Yield Strength Grade Thickness Grade Thickness Grade Thickness
[MPa] [Steel Type] Type] [Steel Type] [MPa] Interval, mm Interval Interval
[Steel Type] [Steel Type] [Steel Type]
Normal 235 AB A 3–10 [Strip] NV A 3–15 [Strip] LR A 3–15 [Strip]
strength 4,8–50 [HR] 4,7–40 [HR] 4,7–40 [HR] Normal 235 PC A 4,8–40 [HR] BV A 3–12 [Strip] RINA A 3–10 [Strip]
steels >50–150 [N] 40–150 [N] 40–150 [N] strength >40–100 [N] 4,7–40 [HR] 5–50 [HR]
steels >40–150 [N] >50–150 [N]
AB B 4,8–50 [HR] NV B 3–15 [Strip] LR B 4,8–16 [HR]
4,8–50 [HR] 4,7–16 [HR] >16–150 [N] PC B 5–40 [HR] BV B 5–16 [HR] RINA B 5–16 [HR]
>16–150 [N] >16 –150 [N] >40–100 [N] >16–150 [N] >16–150 [N
AB D 4,8–19 [HR] NV D 4,8–150 [N] LR D 4,8–150 [N] PC D 5–100 [N] BV D 5–150 [N] RINA D 5–150 [N]
PC E BV E RINA E
AB E 4,8–150 [N] NV E LR E
High 315 PC A32 5–100 [N] BV AH32 5–150 [N] RINA AH32 5–150 [N]
High 315 AH 32 4,8–150 [N] NV A32 5–150 [N] AH 32 4,8–150 [N] strength PC D32 8–50 [TM] BV DH32 8–60 [TM]
strength DH 32 NV D32 8–65 [TM] DH 32 steels PC E32 BV EH32
steels EH 32 NV E32 EH 32
355 PCA 36 2–13 [Strip] BV AH36 5–150 [N] RINA AH 36 4.7–150 [N]
355 AH 36 5,9–15[Strip] NVA 36 2–12[Strip] AH 36 2–13 [Strip] PC D36 5–100 [N] BV DH36 8–65 [TM] RINA DH 36
4,8–150 [N] 4,8–150 [N] 4,8–150 [N] PC E36 8–65 [TM] RINA EH 36
4,8–65 [TM] 8–65 [TM] 8–65 [TM]
PC D36 5–100 [N] BV DH36 4–8 [Strip]
DH 36 4,8–150 [N] NVD 36 2–15[Strip] DH36 4–8 [Strip] PC E36 8–65 [TM] 5–150 [N]
4,8–65 [TM] 4,8–150 [N] 4,8–150 [N] 8–65 [TM]
8–65 [TM] 8–65 [TM]
PCF 36 25–60 [TM] BVE 36 4–8 [Strip]
EH 36 4,8–150 [N] NVE 36 4–8 [Strip] EH 36 5–150 [N] 5–150 [N]
4,8–65 [TM] 4,8–150 [N] 8–65 [TM] 8–65 [TM]
51–75 [QT ] 8–65 [TM]
390 PC A40 5–60 [N]
NV F36 20–65 [TM] AH 40 8–50 [TM] PC D40
390 DH 40 4,8–65 [TM] NVA 40 4–13[Strip] DH 40 8–50 [TM] PC E40
6–40 (N) 8–50 [TM] 6–40 [N] 420 PCD 420 5–60 [TM] BV D420 5–60 [TM])
6–40 (N) PCE 420 BVE 420
NVD 40 8–50 [TM] Extra high 460 PCD 460 5–70 [TM] BVD 460 5–70 [TM]
6–40 (N) strength PCE 460 BVE 460
EH 40 4,8–35 [TM] NVE 40 8–50 [TM] EH 40 8–50 [TM] steels
500 PCD 500 PCE 5–40 [TM] BVD 500 5–40 [TM]
38–60 [QT] 6–40 [N] 6–40 [N] 500 BVE 500
420 DQ 43 8–65 [TM] NVD 420 8–60 [TM] DH 42 8–70 [QT]
20–50 [TM] HR: Hot rolled steel
EQ 43 8–65 [TM] NVE 420 8–60 [TM] EH 42 8–70 [QT] N: Normalized steel
20–50 [TwM]
QT: Quenched and tempered steel
NVF 420 FH 42 8–70 [QT]
TM: Thermo mechanical rolled steel
Extra high 460 DQ 47 8-65 [TM] NVD 460 12 – 60 [TM] DH 46 8-80 [QT]
strength EQ 47 NVE 460 EH 46
steels NVF 460 FH 46
500 DQ 51 8-40 [TM] NVA 500 10 – 40 [TM] DH 50 8-80 [QT
EQ 51 8-40 [TM] NVD 500 9 – 40 [TM] EH 50 10 – 40 [TM]
NVE 500 4 – 80 [QT] FH 50 4 – 80 [QT]
550 DQ 56 Under dev NVD 550 4-80 [QT] DH 55 4-80 [QT]
EQ 56 NVE 550 EH 55
FH 55
620 DQ 63 6,35-38.1 NVD 620 4-80 [QT] DH 62* 8-80 [QT]
EQ 63 [QT] NVE 620 EH 62*
FH 62*
690 DQ 70 4 - 130 [QT] NV D690 4 - 80 [QT] DH 69* 4-80 [QT]
EQ 70 4 - 130 [QT] NV E690 4 - 80 [QT] EH 69* 4-80 [QT]
VL E690 FH 69*
* With a few exceptions, contact for more details.
10 11
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
* The requirements to be agreed. For detailed info contact a SSAB sales representative.
12 13
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
HARDOX® WEAR PLATE FOR TOOLOX® ENGINEERING AND TOOL STEEL FOR
OFFSHORE AND MARINE APPLICATIONS OFFSHORE AND MARINE APPLICATIONS
Hardness [HBW] min-max Thickness Impact toughness Welding properties Toolox® is a pre-hardened engineering and tool steel with a nominal hardness of 300 HBW/33
interval [mm] Transverce [CEV max / typical]
[J/ DegC] HRC or 450 HBW/45 HRC. Despite its high hardness, Toolox® combines very good machinability
with dimensional stability during machining.
Hardox 400 370–430 mm 4–130 45J [-40] –8mm 0,41/
(8)–20 mm 0,46/
(20)–32 mm 0,52/
In applications where further increased surface hardness is required • Dimensional stability.
(32)–45 mm 0,60/ to counteract wear, Toolox® can be nitrided/PVD-coated. Surface • Normally machining can be
(45)–51 mm 0,59/ engineering can be carried out as long as the deposition tempera- done on only one (1) set-up.
(51)–80 mm 0,67/ ture is kept below 590°C. • Faster time to market.
(80)–130 mm 0,76/
Hardox 450 3–80 mm 425–475 0,7–130 27J [-20] –(5)mm 0,48/0,39
80,1–100 mm 410–475 5–(10) mm 0,49/0,45
100,1–130 mm 390–475 10–(20) mm 0,52/0,48
20–(40) mm 0,60/0,56 Hardness [HBW/HRC] Thickness Impact toughness
40–(80) mm 0,74/0,61 Nominal [min–max] interval [mm] Transverce
80–130 mm 0,67/0,64 [J/ DegC]
Typical applications where Hardox® wear plate are used Typical applications where Toolox® engineering and tool steel has been used
Cargo boxes for Barges and Bulk Cargo Vessels Sliding plates in Jack-up rigs Gears Bolts
Dredging buckets Wear plates for deck equipment
Dredging tubes and nozzles Trawl-doors and fishing equipment
14 15
Quality management system in accordance with EN ISO 9001:2008
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
The quality management system at SSAB is based on EN ISO
9001:2008 and is described in our "Operational Manual for
Quality and Environment". The system is certified by an
accredited inspection body, and it is also certified in accordance
with AQAP 2110:3.
Quality Assurance
The approval, which has been issued by TÜV-NORD, applies to accordance with SS-EN 10204:2004. conform to the requirements of the purchase agreement.
products made to EN 10025-1, -2, -3, -4 and -6. The approval The certificates include the particulars specified in the material The results of testing are shown on the products that will be
covers also Strenx 700, Strenx 900 and Strenx 960 and Optim 700 standard, which usually includes: delivered or on inspection batches comprising part of the prod-
QL. • name of manufacturer ucts delivered.
• clear reference to the purchase agreement and delivery batch Document issued both by the inspection representative
• material designation in accordance with the purchase authorized by the manufacturer and either by an inspection
agreement representative authorized by the customer or by an inspector
• description of article appointed in accordance with official regulations.
• nominal dimensions
• quantity
• results of inspection (although not type 2.1 certificate below)
• date of issue.
16 17
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
and safety of the product. 029. Class A and B also conform to or are stricter than specified –(4 000) +20 0
in EN 10 051. 4 000–(6 000) +30 0
6 000–(8 000) +40 0
Through constant process improvements, Strenx® performance
steel is delivered with a unique set of guarantees for thickness,
Bending guarantee 8 000–(10 000) +50 0
flatness and bending properties. Strenx® guarantees are your The bending guarantee depends on the yield s trength of the 10 000–(15 000) +75 0
safeguard for trouble-free production, day after day, year after steel grade, and always conforms to or is more stringent than the
15 000–18 000 +100 0
year. And the material can be processed by the same kind of requirements in the relevant EN standard for each product.
machinery and technology used for conventional steel. You can find detailed information about the Strenx® guarantees
Nominal thickness Width Tolerances [mm]
SSAB is the world’s most experienced producer of high-end in the separate Strenx® guarantees brochure. [mm]
Max. Min.
quenched and tempered steels. Strenx® performance steel’s
extreme cleanness, lean alloy solution and high-quality man- –(40) +2 0
ufacturing processes have great impact on toughness, fatigue 40–(150) +2 0
strength and performance in sub-zero conditions.
150– +3 0
Since Strenx® is stronger, it can be used in thinner dimensions
to make lighter structures. It improves the final product, and it
STRENX
brings benefits along the way. Thinner material usually means less GUARANTEES For plate thickness up to and including 20 mm, plasma cutting
enables us to offer closer tolerances on length and width than
welding and faster production. Everyday handling in the workshop
those tabulated above. SSAB can also offer plates delivered
becomes easier, and there is less steel to take up storage space.
with mill edges and tolerances on length either according to EN
When new design and innovative solutions require new and
10029 or according to SSAB Extra Wide.
smarter production methods, you can always turn to SSAB Tech
Support for guidance and recommendations. SSAB is happy to
provide you with expert advice on materials and processing when
you are developing new and improved applications.
Strenx® guarantees
Strenx® guarantees cover thickness tolerances, flatness tolerances
and bending properties.
Thickness guarantee
Strenx®
The thickness tolerances are more narrow than those specified in guarantees
the relevant EN standards for each product group. brochure
18 19
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
TESTING MARKING
Unless otherwise agreed, inspection and testing SSAB plate normally fulfill class E1, S1 in accordance with EN All plate is clearly marked on delivery. The steel The customer’s mark, plate dimensions of length, width and thick-
10160:1999. ness, and the serial number of the plate, the batch number, and
is carried out and the results are reported as Ultrasonic testing is carried out and reported on the test cer- grade and the plate identity are stamped, unless the in-house pile number are painted on the plate as required by
specified in the relevant material standard or in tificates if ordered, in accordance with EN 10 160, SEL 072, ASTM the relevant standard specifies no stamping or means of white paint or with a dark ink jet.
435, ASTM 578 or other agreed standard. For plate thicknesses in Stamping and marking with paint are carried out by machine or
our data sheets. When placing the order, always excess of 100 mm and requirements stricter than those corre- after special agreement. If stamping is not car- manually. When done by machine, all marking with paint is carried
specify whether the material is to be subjected sponding to E0S0, testing for test certificate is carried out only ried out for any reason, stamping is replaced by out by dot-matrix printing and stamping is carried out by means
after special agreement. of rounded stamps.
to special inspection, the scope of such inspec- marking with white paint or with a dark ink jet.
tion, and also the type of inspection document Z-Testing Brand marking
required. Almost all of the steels can be supplied with guaranteed prop- The plate identity is specified by In order to eliminate the risk of material mix-ups at the desti-
erties in the through thickness direction, Z-plate according to two digit groups nation, our plate is marked as follows, unless otherwise agreed:
EN 10164. For pressure vessel steel and offshore/shipping steel, Painted plate is normally marked in a number of rows over the
The plates are marked with unique numbers of heat and plate
Mechanical testing unless otherwise agreed, the maximum thickness is 150 mm. For
enabling full traceability.
whole of the plate surface. Unless otherwise agreed, a simplified
Tensile testing in accordance with ISO 6892. Impact testing in structural steel with a yield strength up to 400 MPa the thickness steel grade designation and SSAB are painted. The plate identity
If required or if so decided by SSAB, the location of the
accordance with ISO 148. Tensile testing in the thickness direction limits are as follows; Z15 up to 100 mm, Z25 up to 90 mm and Z35 number can also be marked in rows over the plate surface.
stamped marking can be shown by two white-paint dots.
in accordance with EN 10164. up to 80 mm. Z-Plate in higher thicknesses than here mentioned Note that the complete steel grade designation in accordance
Stamping is always carried out at right angles to the direction
can be approved depending on grade and dimension. with the standard/data sheet or specification is stamped or is
of rolling. Marking with paint may be carried out in the direction
included in the paint marking.
Ultrasonic testing of rolling. On plate that is not stamped, the direction of rolling is
Ultrasonic testing is used for indicating cracks, inclusions, porosi- therefore shown by a painted arrow. A painted arrow can also be
ty and similar discontinuities. shown on stamped plates.
Surface Testing 1)
As per EN 10160 Distance between parallel Min. defect area to register Max. permissible defect Max. number of defects
scanning lines [mm] [mm2] area [mm2] [defects/m2]
20 21
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
22 23
SSAB PRODUCTS FOR OFFSHORE AND MARINE INDUSTRIES
Social icon
Rounded square
Only use blue and/or white.
SSAB
S-613 80 Oxelösund
Sweden
www.ssab.com/offshore