Professional Documents
Culture Documents
Bizhub Pro 1050 SM
Bizhub Pro 1050 SM
1050/1050P/
1050e/1050eP
Info MA: Neu Juli 2007
Geänderte Seiten (lt. Seitenzahl im Dokument):
3,9,29,29-1,32,35,194,195,214,215,378,381,383,
385,385-1,385-2,413,418,419,567,716,719,723,
724,726,752,819,820,821,822,823
2006.11
Ver. 3.0
FIELD SERVICE TOTAL CONTENTS
DF-603
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 27
* For particulars, see the contents of DF-603.
PF-701/PP-701
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 51
* For particulars, see the contents of PF-701/PP-701.
FD-501
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 49
* For particulars, see the contents of FD-501.
LS-501/502
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 23
* For particulars, see the contents of LS-501/502.
i
FS-503
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 39
* For particulars, see the contents of FS-503.
SD-501
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 9
ADJUSTMENT/SETTING ............................................................................................. 63
* For particulars, see the contents of SD-501.
PB-501
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 55
* For particulars, see the contents of RC-501.
RC-501
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
* For particulars, see the contents of PB-501.
IC Unit
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
ADJUSTMENT / SETTING ........................................................................................... 23
TROUBLESHOOTING ................................................................................................. 25
* For particulars, see the contents of IC Unit.
ii
SAFETY AND IMPORTANT WARNING ITEMS
IMPORTANT NOTICE
Because of possible hazards to an inexperienced person servicing this product as well as the risk of damage to
the product, Konica Minolta Business Technologies, INC. (hereafter called the KMBT) strongly recommends that
all servicing be performed only by KMBT-trained service technicians.
Changes may have been made to this product to improve its performance after this Service Manual was printed.
Accordingly, KMBT does not warrant, either explicitly or implicitly, that the information contained in this Service
Manual is complete and accurate.
The user of this Service Manual must assume all risks of personal injury and/or damage to the product while ser-
vicing the product for which this Service Manual is intended.
Therefore, this Service Manual must be carefully read before doing service work both in the course of technical
training and even after that, for performing maintenance and control of the product properly.
Keep this Service Manual also for future service.
Symbols used for safety and important warning items are defined as follows:
S-1
SAFETY AND IMPORTANT WARNING ITEMS
SAFETY WARNINGS
Prohibited Actions
DANGER
• Using any fuse or thermostat not specified by KMBT. Safety will not be
assured, leading to a risk of fire and injury.
• Disabling fuse functions or bridging fuse terminals with wire, metal clips, sol-
der or similar object.
• Disabling safety functions (interlocks, safety circuits, etc.) Safety will not be
assured, leading to a risk of fire and injury.
S-2
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Use power supply cord set which meets the following criteria:
- provided with a plug having configuration intended for the connection AC230V
to wall outlet appropriate for the product's rated voltage and current,
and
- the plug has pin/terminal(s) for grounding, and
- provided with three-conductor cable having enough current capacity,
and
- the cord set meets regulatory requirements for the area.
AC208V 240V
Use of inadequate cord set leads to fire or electric shock.
S-3
SAFETY AND IMPORTANT WARNING ITEMS
1. Power Supply
WARNING
?V
• Connect power plug directly into wall outlet having same configuration as
the plug.
Use of an adapter leads to the product connecting to inadequate power kw
supply (voltage, current capacity, grounding), and may result in fire or
electric shock.
If proper wall outlet is not available, advice the customer to contact quali-
fied electrician for the installation.
• Plug the power cord into the dedicated wall outlet with a capacity greater
than the maximum power consumption.
If excessive current flows in the wall outlet, fire may result.
• If two or more power cords can be plugged into the wall outlet, the total load
must not exceed the rating of the wall outlet.
If excessive current flows in the wall outlet, fire may result.
• Make sure the power cord is plugged in the wall outlet securely.
Contact problems may lead to increased resistance, overheating, and the
risk of fire.
S-4
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• When using the power cord set (inlet type) that came with this product,
make sure the connector is securely inserted in the inlet of the product.
When securing measure is provided, secure the cord with the fixture prop-
erly.
If the power cord (inlet type) is not connected to the product securely, a
contact problem may lead to increased resistance, overheating, and risk
of fire.
• Check whether the power cord is not stepped on or pinched by a table and
so on.
Overheating may occur there, leading to a risk of fire.
• Check whether the power cord is damaged. Check whether the sheath is
damaged.
If the power plug, cord, or sheath is damaged, replace with a new power
cord or cord set (with plug and connector on each end) specified by
KMBT.
Using the damaged power cord may result in fire or electric shock.
• Check whether dust is collected around the power plug and wall outlet.
Using the power plug and wall outlet without removing dust may result in
fire.
• Do not insert the power plug into the wall outlet with a wet hand.
The risk of electric shock exists.
• When unplugging the power cord, grasp the plug, not the cable.
The cable may be broken, leading to a risk of fire and electric shock.
S-5
SAFETY AND IMPORTANT WARNING ITEMS
Wiring
WARNING
• Never use multi-plug adapters to plug multiple power cords in the same out-
let.
If used, the risk of fire exists.
• When an extension cord is required, use a specified one. Current that can
flow in the extension cord is limited, so using a too long extension cord may
result in fire.
Do not use an extension cable reel with the cable taken up. Fire may
result.
2. Installation Requirements
WARNING
• Do not place the product near flammable materials or volatile materials that
may catch fire.
A risk of fire exists.
• Do not place the product in a place exposed to water such as rain.
A risk of fire and electric shock exists.
WARNING
• When the product is not used over an extended period of time (holidays,
dust collected around the power plug and outlet may cause fire.
Ventilation
CAUTION
• The product generates ozone gas during operation, but it will not be harmful
to the human body.
If a bad smell of ozone is present in the following cases, ventilate the
room.
a. When the product is used in a poorly ventilated room
b. When taking a lot of copies
c. When using multiple products at the same time
S-6
SAFETY AND IMPORTANT WARNING ITEMS
Fixing
CAUTION
• Be sure to lock the caster stoppers.
In the case of an earthquake and so on, the product may slide, leading to
a injury.
CAUTION
• Before conducting an inspection, read all relevant documentation (service
manual, technical notices, etc.) and proceed with the inspection following
the prescribed procedure in safety clothes, using only the prescribed tools.
Do not make any adjustment not described in the documentation.
If the prescribed procedure or tool is not used, the product may break
and a risk of injury or fire exists.
• Before conducting an inspection, be sure to disconnect the power plugs
from the product and options.
When the power plug is inserted in the wall outlet, some units are still
powered even if the POWER switch is turned OFF. A risk of electric shock
exists.
WARNING
• Take every care when making adjustments or performing an operation
check with the product powered.
If you make adjustments or perform an operation check with the external
cover detached, you may touch live or high-voltage parts or you may be
caught in moving gears or the timing belt, leading to a risk of injury.
• Take every care when servicing with the external cover detached.
High-voltage exists around the drum unit. A risk of electric shock exists.
S-7
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• Check the exterior and frame for edges, burrs, and other damages.
The user or CE may be injured.
• Do not allow any metal parts such as clips, staples, and screws to fall into
the product.
They can short internal circuits and cause electric shock or fire.
• Check electrode units such as a charging corona unit for deterioration and
sign of leakage.
Current can leak, leading to a risk of trouble or fire.
• Do not remove the cover of the write unit. Do not supply power with the
write unit shifted from the specified mounting position.
The laser light can enter your eye, leading to a risk of loss of eyesight.
• When replacing a lithium battery, replace it with a new lithium battery speci-
fied in the Parts Guide Manual. Dispose of the used lithium battery using the
method specified by local authority.
Improper replacement can cause explosion.
• After replacing a part to which AC voltage is applied (e.g., optical lamp and
fixing lamp), be sure to check the installation state.
A risk of fire exists.
S-8
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• Check the interlock switch and actuator for loosening and check whether
the interlock functions properly.
If the interlock does not function, you may receive an electric shock or be
injured when you insert your hand in the product (e.g., for clearing paper
jam).
• Make sure the wiring cannot come into contact with sharp edges, burrs, or
other pointed parts.
Current can leak, leading to a risk of electric shock or fire.
• Make sure that all screws, components, wiring, connectors, etc. that were
removed for safety check and maintenance have been reinstalled in the orig-
inal location. (Pay special attention to forgotten connectors, pinched cables,
forgotten screws, etc.)
A risk of product trouble, electric shock, and fire exists.
Handling of Consumable
WARNING
• Toner and developer are not harmful substances, but care must be taken
not to breathe excessive amounts or let the substances come into contact
with eyes, etc. It may be stimulative.
If the substances get in the eye, rinse with plenty of water immediately.
When symptoms are noticeable, consult a physician.
S-9
SAFETY AND IMPORTANT WARNING ITEMS
CAUTION
• Do not replace the cover or turn the product ON before any solvent rem-
nants on the cleaned parts have fully evaporated.
A risk of fire exists.
• Use only a small amount of cleaner at a time and take care not to spill any
liquid. If this happens, immediately wipe it off.
A risk of fire exists.
S-10
SAFETY AND IMPORTANT WARNING ITEMS
SAFETY INFORMATION
IMPORTANT NOTICE
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented
regulations for laser products manufactured since August 1, 1976. Compliance is mandatory for products mar-
keted in the United States.
This copier is certified as a "Class 1" laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation
Control for Health and Safety Act of 1968. Since radiation emitted inside this copier is completely confined
within protective housings and external covers, the laser beam cannot escape during any phase of normal user
operation.
S-11
SAFETY AND IMPORTANT WARNING ITEMS
S-12
SAFETY AND IMPORTANT WARNING ITEMS
S-13
SAFETY AND IMPORTANT WARNING ITEMS
1050sa002e
S-14
SAFETY AND IMPORTANT WARNING ITEMS
CAUTION
The paste tank
unit is very hot.
To avoid getting
burned DO NOT
TOUCH.
1050sa005e
CAUTION:
You may be burned or injured if you touch any area that you are advised by any caution label to keep your-
self away from. Do not remove caution labels. And also, when the caution label is peeled off or soiled and
cannot be seen clearly, replace it with a new caution label.
S-15
SAFETY AND IMPORTANT WARNING ITEMS
S-16
Composition of the service manual
The details of items with an asterisk "*" are described only in the service manual of the main
body.
C-1
Notation of the service manual
1. Product name
In this manual, each of the products is described as follows:
(1) IC board: Standard printer
(2) KonicaMinolta bizhub PRO 1050/1050P/1050e/1050eP:Main body
(3) PS-502 PostScript3 Option: PS3 Option
(4) Microsoft Windows 95: Windows 95
Microsoft Windows 98: Windows 98
Microsoft Windows Me: Windows Me
Microsoft Windows NT 4.0: Windows NT 4.0 or Windows NT
Microsoft Windows 2000: Windows 2000
Microsoft Windows XP: Windows XP
When the description is made in combination of the OS's mentioned above:
Windows 95/98/Me
Windows NT 4.0/2000
Windows NT/2000/XP
Windows 95/98/Me/ NT/2000/XP
2. Brand name
The company names and product names mentioned in this manual are the brand name or the registered
trademark of each company.
C-2
Classification Load symbol Ex. of signal name Description
_U
_V
_W
Drive signals (control signals) of three kinds
DRV1
DRV2
DRV3
D1
D2
D3
D4
DRV A
DRV A
DRV B Drive signals (control signals) of four kinds
DRV B Motor, phases A and B control signals
A
Motor M /A
B
/B
AB
BB
CLK, PLL PLL control signal
LCK, Lock, LD PLL lock signal
FR Forward/reverse rotation signal
EM, Lock, LCK, LD Motor lock abnormality
BLK Drive brake signal
P/S Power/stop
S/S
Operating load start/stop signal
SS
CW/CCW, F/R Rotational direction switching signal
ENB Effective signal
TEMP_ER Motor temperature abnormality detection signal
24V Power to drive the fan motor
CONT, DRIVE Drive signal
Fan FM
HL Speed control signal (2 speeds)
EM, Lock, LCK, FEM Detection signal
Others TH1.S, ANG Analog signal
SG, S.GND, S_GND Signal ground
Ground
PG, P.GND Power ground
C-3
Classification Load symbol Ex. of signal name Description
DCD Data carrier detection
SIN Serial input
SOUT Serial output
DTR Data terminal operation available
GND Signal ground (earth)
Serial commu-
DSR, DSET Data set ready
nication
RTS Transmission request signal
CTS Consent transmission signal
RI Ring indicator
TXD Serial transmission data
RXD Serial reception data
<Example>
C-4
SERVICE MANUAL Field Service
1050/1050P/
1050e/1050eP
Main body
2006.11
Ver. 3.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left ass they are.
1050e/1050eP
bizhub PRO 1050/1050P/1050e/1050eP
OUTLINE
1. SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. PRODUCT SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Type of paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.5 Machine data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.6 Operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MAINTENANCE
3. PERIODIC CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Life value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Maintenance item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3.1 Main body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3.2 DF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3.3 PF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.4 FD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.3.5 LS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3.6 FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3.7 SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.8 PB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.3.9 RC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4 Replacement parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4.1 Main body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4.2 Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.4.3 Spot replacement parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.5 Maintenance procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.5.1 External section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.5.2 Photo conductor section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.5.3 Developing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
3.5.4 Toner supply section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3.5.5 Cleaning/toner recycle section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
3.5.6 Paper feed section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3.5.7 Vertical conveyance section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
3.5.8 ADU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
3.5.9 Fusing section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
3.5.10 Paper exit section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
4. SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
4.1 Service material list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
4.2 Jig list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
4.3 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
4.4 Mail remote notification system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
i
CONTENTS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
ii
Field Service Ver3.0 Nov.2006 CONTENTS
1050e/1050eP
ADJUSTMENT/SETTING
7. HOW TO USE THE ADJUSTMENT / SETTING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
7.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
8. LIST OF ADJUSTMENT ITEMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
9. UTILITY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
9.1 List of utility modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
10. SERVICE MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
10.1 Setting method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
10.1.1 Start and exit service mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
10.2 List of service mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
10.3 Machine adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
10.3.1 Tray adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
10.3.2 Magnification adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
10.3.3 Timing adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
10.3.4 Centering adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
10.3.5 Warp adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
10.3.6 Non-image area erase check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
10.3.7 ADF adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
10.3.8 Recall standard data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
10.4 Process adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
10.4.1 High voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
10.4.2 Drum peculiarity adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
10.4.3 Drum peculiarity manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
10.4.4 User paper setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
10.4.5 Recall standard data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
10.5 Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
10.5.1 PM count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
10.5.2 Data collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
10.5.3 Copy count of part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
10.6 Machine condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
10.6.1 I/O check mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
10.7 List output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
10.7.1 List output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
10.8 Test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
10.8.1 Test pattern output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
10.8.2 Test pattern density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
10.8.3 Running test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
10.9 System setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
10.9.1 Software DIPSW setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
10.9.2 Telephone number setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
10.9.3 Serial number setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
10.9.4 Setting date input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
10.10 ROM version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
10.11 CS Remote Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
10.11.1 Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
10.11.2 Setup procedure of the CS Remote Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
10.11.3 List of combinations of E-Mail CS Remote Care and Mail remote notification system. . . . . . . 454
iii
CONTENTS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
iv
Field Service Ver3.0 Nov.2006 CONTENTS
1050e/1050eP
12.5 Overlay printing adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525
12.6 User setting of each paper brand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
12.7 Settings for feeding carbonless paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
TROUBLESHOOTING
13. JAM CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
13.1 Jam code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
14. MALFUNCTION CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
14.1 Malfunction code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
APPENDIX
15. ELECTRICAL PARTS LAYOUT DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651
15.1 Main body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651
15.2 DF-603 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
15.3 PF-701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678
15.4 FD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683
15.5 LS-501/502. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
15.6 FS-503 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695
15.7 SD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
15.8 PB-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713
16. CONNECTOR LAYOUT DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728
16.1 Main body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728
16.2 DF-603 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
16.2.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
16.3 PF-701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740
16.3.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740
16.4 FD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
16.4.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
16.5 LS-501/502. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745
16.5.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745
16.6 FS-503 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747
16.6.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747
16.7 SD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749
16.7.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749
16.8 PB-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751
16.8.1 Connector in the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751
17. TIMING CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753
17.1 Main body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753
17.2 DF-603 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755
17.3 PF-701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 757
17.4 FD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 758
17.5 LS-501/502. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
17.6 FS-503 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 770
17.7 SD-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773
17.8 PB-501 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 779
18. OVERALL WIRING DIAGRAM
18.1 Main body 1/4
v
CONTENTS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
18.5 DF-603
18.6 PF-701
18.7 FD-501
18.8 LS-501/502
18.9 FS-503
18.10 SD-501 1/4
18.11 SD-501 2/4
18.12 SD-501 3/4
18.13 SD-501 4/4
18.14 PB-501 1/4
18.15 PB-501 2/4
18.16 PB-501 3/4
18.17 PB-501 4/4
19. PAPER SETTING
19.1 Relationship between the optimum value and the control of each of setting items by paper brand
(U.S.A. paper) (for fusing hard roller)
19.2 Relationship between the optimum value and the control of each of setting items by paper brand
(U.S.A. paper) (for fusing soft roller)
19.3 Relationship between the optimum value and the control of each of setting items by paper brand
(European paper) (for fusing hard roller)
19.4 Relationship between the optimum value and the control of each of setting items by paper brand
(European paper) (for fusing soft roller)
19.5 Conversion table of paper weight
vi
Field Service Ver3.0 Nov.2006 1. SYSTEM CONFIGURATION
1050e/1050eP
1. SYSTEM CONFIGURATION
A. System configuration
[4] [3]
[14]
[8]
[1]
[2]
[5]
[9]
[13]
[10]
[6]
[12]
[7]
[11]
1050to1001ea
2 1
1. SYSTEM CONFIGURATION Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3] Double sided original auto feeder (DF-603) *1 [10] Side cover *2
[4] Flat stapling finisher (FS-503) [11] Hand cart (LC-501)
[5] Punch and multi folding finisher (FD-501) [12] Simplified perfect binding machine (PB-501)
[6] Large capacity stacker (LS-501) [13] Saddle stitching trimmer finisher (SD-501)
[7] Large capacity stacker (LS-502) [14] Overlay printing kit (PP-701)
[8] Toner recycle cut kit (RC-501)
NOTE
• The option can be connected. However, be sure to take note of the AC connection mode.
Coupling combination of the main body and the finisher option AC power to be connected to
1 Main body LS-502 —
2 Main body FD-501 FS-503 External (FD-501)
3 Main body SD-501 External (SD-501)
4 Main body FD-501 SD-501 External (FD-501/SD-501)
5 Main body FD-501 PB-501 External (FD-501/PB-501)
6 Main body FD-501 SD-501 FS-503 External (FD-501/SD-501)
7 Main body FD-501 SD-501 PB-501 External (FD-501/SD-501/PB-501)
8 Main body FS-503 —
9 Main body LS-501 LS-501 FS-503 External (1st tandem LS-501)
External (2nd tandem LS-501)
NOTE
• Any coupling formation other than the above is unavailable.
• PF-701 can be either connected or disconnected.
2 2
Field Service Ver3.0 Nov.2006 2. PRODUCT SPECIFICATIONS
1050e/1050eP
Type: Console type (floor-mounted type)
Copying method: Indirect electrostatic method
Original stand: Fixed
Original alignment: Left rear standard
Photosensitive material: OPC
Sensitizing method: Laser writing
Paper feed trays: Two trays (1,500 sheets x 2, 20lb, 80 gsm)
PF-701 (2,000 x 3, 80 gsm) *1
*1 The PF-701 is optional.
2.2 Functions
Original: Sheet, book, solid object
Maximum original size: A3, or 11 x 17
Copy size:
Tray /1, /2: Inch: 12 x 18, 11 x 17, 81/2 x 14, 81/2 x 11, 81/2 x 11R, 51/2 x 81/2, A3, B4,
A4, B5, B5S, 8 x 13, 81/4 x 131/4, 81/4 x 13, 81/2 x 13, wide paper *1
(up to 324 mm x 460 mm), standard index paper
Metric:A3, B4, A4, A4S, B5, B5S, A5, 12 x 18, 11 x 17, 81/2 x 14, 81/2 x
11, 8 x 13, 81/8 x 131/4 , 81/4 x 13, 81/2 x 13, wide paper (up to 324
mm x 460 mm), standard index paper
ADU: A3, B4, A4, A4S, B5, B5S, A5, 12 x 18, 11 x 17, 81/2 x 14, 81/2 x 11, 51/2
x 81/2, 81/2 x 11R, 8 x 13, 81/8 x 131/4, 81/4 x 13, 81/2 x 13, wide paper (up to
324 mm x 460 mm)
*1 When use wide paper as a cover paper in the perfect binding mode: up to 307 mm x 460 mm
Magnification:
Fixed magnification: Inch: x 1.000, x 2.000, x 1.545, x 1.294, x 1.214, x 0.785, x 0.772,
x 0.647, x 0.500
Metric:x 1.000, x 2.000, x 1.414, x 1.224, x 1.154, x 0.866, x 0.816,
x 0.707, x 0.500
Special magnification setting: 3 types
Zoom magnification: x 0.250 to x 4.000 (at the step of 0.1%)
Vertical magnification: x 0.250 to x 4.000 (at the step of 0.1%)
Horizontal magnification: x 0.250 to x 4.000 (at the step of 0.1%)
Warm-up time Hard roller: Less than 6 min. (under 20°C, at rated voltage)
Soft roller: Less than 8 min. (under 20°C, at rated voltage)
First copy out time Hard roller: Less than 3.0 sec.
Soft roller: Less than 9.0 sec.
Continuous copy speed: 105 copies/min. (for A4/81/4 x 11)
Continuous copy count: Up to 9,999 sheets
Copy density selection: AE/AES, manual (9 steps), user density (2 steps)
Resolution:
Scan: 600 dpi x 600 dpi
Write: 600 dpi x 600 dpi
Memory: 256 MB (DRAM) + 10 GB (HDD1)
Interface section: RJ45 Ethernet, Serial port (RS232-C): Main body right side
2 3
2. PRODUCT SPECIFICATIONS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Serial port (USB Type B), Parallel port: Mounted on the Image process-
ing board (IPB)
No. of originals to be stored: More than 10,000 sheets
/1050e/1050eP
2.4 Maintenance
Maintenance: Once every 750,000 prints
Machine service life: 40,000,000 prints or 7 years (whichever earlier)
4 2
Field Service Ver3.0 Nov.2006 2. PRODUCT SPECIFICATIONS
1050e/1050eP
Metric: AC230V ± 10%, 50Hz
Power consumption: Inch: Less than 3600W (full option)
Metric: Less than 3450W (full option)
Weight: 1050/1050e: Approx. 330 kg (with DF provided) /
1050P/1050eP: Approx. 310 kg
Dimensions:
1050/1050e: W 895 mm x D 775 mm x H 1190 mm
1050P/1050eP: W 895 mm x D 775 mm x H 1020 mm
1050/1050e + PF-701 + FD-501 + FS-503: W 2902 mm x D 775 mm x H 1190 mm
1050P/1050eP + PF-701 + LS-501 + LS-502: W 3292 mm x D 775 mm x H 1020 mm
(with no operation board included in each case)
NOTE
• The information herein May be subject to change for improvement without notice.
2 5
2. PRODUCT SPECIFICATIONS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
/1050e/1050eP
Blank page
6
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
3. PERIODIC CHECK
3.1 Life value
A. Life value of materials
B. Life value
The life value is a value for the number of prints or a value for the drive time, whichever is earlier.
The relationship between the driving time mentioned above and the actual number of prints has certain condi-
tions. It is decided according to the amount of copy time and also idling time*. Accordingly, the number of prints
can vary substantially for the same amount of rotation time.
* Idling time: Time period during which the drum or developing roller is rotating with no image created.
Reference: Relationship between the number of prints and the drive time
220 hours drive at A4 continuous output of 11 sheets per job is equivalent to 1,000,000 prints.
Caution:
• Developer/drum replacement icon is generated only by print count or running time. The trigger
can be switched between print count and running time by setting of the DIPSW 15-7 in the service
mode.
1 7
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.2 Schedule
Guarantee period (7 years or 40,000,000 prints)
/1050e/1050eP
0
75
100
150
200
225
250
300
350
375
400
450
500
525
550
600
650
675
700
750
800
825
850
900
950
975
1000
2000
3800
3825
3850
3900
3950
3975
Maintenance 1 z z z z z z z z z z z z z xxxzxxx z z z 53
Main body
8
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
0
75
100
150
200
225
250
300
350
375
400
450
500
525
550
600
650
675
700
750
800
825
850
900
950
975
1000
2000
3800
3825
3850
3900
3950
3975
1050e/1050eP
Maintenance 1 z z z z z z z z z z z z z xxxzxxx z z z 53
SD
2 9
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• For cleaning of the tools used, be sure to use a vacuum cleaner appropriate for cleaning toner.
NOTE
• For the part number of periodically replaced parts, see "Parts guide manual."
• For the replacement procedure of periodically replaced parts, see "3.5 Maintenance procedure".
10
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
section photo conductor sec-
tion
6 Writing Cleaning of the dust- z Cleaning pad
section proof glass
7 ADU Cleaning of each sensor z Blower brush
Cleaning of the pre- z Drum cleaner/
transfer roller cleaning pad
Cleaning of the loop z
roller
Cleaning of the ADU z
exit roller
Cleaning of the ADU z
conveyance roller /2
Cleaning of the ADU z
conveyance roller /3
Cleaning of the ADU z
conveyance roller /4
Cleaning of the ADU z
conveyance roller /1
Cleaning of the ADU z
reverse roller
Cleaning of the ADU z
reverse/exit roller
Cleaning of the ADU z
acceleration roller
Cleaning of the paper z
exit roller /1
Cleaning of the paper z
exit roller /2
Cleaning of the fusing z
exit roller
Cleaning of the convey- z
ance section
8 Registration Cleaning of the paper dust z Vacuum cleaner/
section removing brush for the blower brush
registration roller /Lw
Cleaning of the paper dust z
removing brush for the
registration roller /Up
Cleaning of the registra- z Blower brush
tion sensor section
Cleaning of each sensor z
11
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
machine internal cleaning pad
17 Final check Check of the image and z
the paper through (with
various types of adjust-
ments included)
PM counter reset z
(in service mode)
13
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
14 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
1 Paper feed Pick-up roller 2 Actual replacement
z
section 55VA-484# cycle: 500,000
Paper feed roller 2
z
55VA-483#
Separation roller 2
z
55VA-483#
1 15
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
16
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
56UA4741# cycle: 6,000,000
ADU reverse roller 1 z
56UA4741#
ADU conveyance roller /1 1 z
56UA47442E
ADU conveyance roller /2 1 z
56UA47442E
ADU conveyance roller /3 1 z
56UA4595#
ADU conveyance roller /4 1 z
56UA4683#
ADU exit roller 1 z
56UA4683#
Fusing exit roller 1 z
56UA4595#
4 Registration Registration roller /Up 1 z
section 56UA46061E
Registration bearing 2 z
56UA7602#
5 Transfer/ Transfer/separation 1 z
separation charger unit
charger 56UA-270#
TSL 1 z
55VA8308#
6 Fusing Fusing gear 1 z
section 56UA7783#
Web motor 1 z
56GA8017#
Fusing actuator 1 z
56UA5383#
7 Paper exit Cleaning of the paper z Blower brush
section exit sensor
Main body paper exit 1 z
roller
56UA45571E
8 Cleaning/ Cleaning gear /A assem- 1 z
toner recycle bly
section 56GA-556#
2 17
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
18 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Preparations Original through check z
Cover z
2 Paper feed Pick-up roller z Drum cleaner/
section Paper feed roller z cleaning pad
Paper feed assist roller z
Cleaning pad z
Registration roller z
Pre-handling rubber z
Original count sensor z Blower brush
Original size sensor /Lt z
Original size sensor /Rt z
3 Conveyance Original registration z
section sensor /Lt
Original registration z
sensor /Rt
4 Read Original conveyance z
section sensor
Original skew sensor / z
Rr
Original skew sensor /Fr z
5 Paper exit Mirror on the driven z
section roller assembly
Original reverse sensor z
Reverse jam sensor z
Original reverse/exit z
sensor
6 Final check Paper through check z
Cleaning of the cover z Drum cleaner/
cleaning pad
19
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.3.3 PF
A. Maintenance 1 (Every 750,000 prints)
20
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
1 Conveyance Pre-registration clutch /1 1 z Actual replacement
section 56AA8201# cycle: 3,000,000
Pre-registration clutch /2 1 z
56AA8201#
Pre-registration clutch /3 1 z
56AA8201#
Intermediate clutch /Up 1 z
56AA8201#
Intermediate clutch /Lw 1 z
56AA8201#
2 Tray section Paper dust removing 3 z
brush
15BY5604#
2 21
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
22 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Preparations Paper through check z
2 PI section Paper feed rubber 2 z Actual replacement
50BA-575# cycle: 100,000
Separation rubber 2 z
13QN-443#
Cleaning of each sensor z Blower brush
3 Tray up/down Cleaning of each sensor z
section
4 Punch Cleaning of each sensor z
section
5 Conveyance Cleaning of each sensor z
section
6 Final check Paper through check z
Cleaning of the cover z Drum cleaner/
cleaning pad
23
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
24
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Preparations Paper through check z
2 Conveyance Paper press solenoid /3 1 z Actual replacement
section 15AV8255# cycle: 5,000,000
Paper press solenoid /1 1 z
15AV8252#
Paper press solenoid /2 1 z
15AV8251#
Rear stopper solenoid 1 z
15AV8253#
Stacker tray up down 1 z
motor
15AV8003#
Cleaning of each sensor z Blower brush
3 Final check Paper through check z
Cleaning of the cover z Drum cleaner/
cleaning pad
25
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.3.6 FS
A. Maintenance 1 (Every 750,000 prints)
26 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Right angle Right angle conveyance z Blower brush
conveyance sensor /1
2 section Right angle conveyance z
sensor /2
3 Right angle conveyance z Drum cleaner/
roller /1 cleaning pad
4 Right angle conveyance z
roller /2
5 Right angle conveyance z
roller /3
6 Right angle conveyance z
roller /4
7 Folding Folding main scan align- z Blower brush
section ment home sensor /Fr1
8 Folding main scan align- z
ment home sensor /Fr2
9 Folding entrance roller /1 z Drum cleaner/
10 Folding entrance roller /2 z cleaning pad
11 Folding entrance roller /3 z
12 Saddle Saddle stitching paper z Blower brush
stitching sensor
13 section Bundle sensor /1 z
14 Bundle pro- Bundle sensor /2 z
cessing sec-
tion
15 Trimmer Trimmer scraps full sensor z
16 section Trimmer board assembly z Actual replacement
15AN5282# cycle: 18,900 cuts
2 27
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
28 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Conveyance Entrance sensor z Blower brush
2 section SC entrance sensor z
3 Sub tray conveyance roller z Drum cleaner/
4 Intermediate conveyance roller z cleaning pad
5 Entrance conveyance roller z
6 Cover paper conveyance roller z
7 Glue tank Glue tank z z*2 Tweezers, industrial
section wiper, multemp FF-RM
8 Filter z
A0753724#
9 Cover paper Cover paper folding z*1 Tweezers, industrial wiper
section plate
2 29
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
*1 Cleaning of the cover paper folding plate and the book spine backing plate is an abbreviated cleaning.
Remove adhered glue as necessary.
*2 Lubricate the glue apply roller motor drive connecting gear.
*3 Lubricate the cover paper alignment plate shafts.
29-1 2
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.3.9 RC
A. Maintenance 1 (Every 750,000 prints)
30 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• For the part number of periodically replaced parts, see "Parts guide manual."
• For the replacement procedure of periodically replaced parts, see "3.5 Maintenance procedure".
• The parts count No. given in the table below represents the number of the fixed parts number in
the service mode.
No. Classification Part name Part number Qt. Actual Parts count
replacement No.
cycle
1 Main body Ozone filter /A 56UA1121# 2 4,500,000 32
2 Ozone filter /K 56UA1128# 1 4,500,000 32
3 Conveyance suction filter 56UA1129# 1 4,500,000 33
4 Developing suction filter 56UA1122# 1 4,500,000 33
5 Photo con- Drum temperature sensor 56GA-209# 1 3,000,000 22
6 ductor section Drum DR010 1 * 1,000,000
7 Drum claw 57GA2919# 3 1,000,000 9
8 Charger Charger unit 56UA-250# 1 6,000,000 34
9 Charger control plate 56UA2508# 1 750,000 4
10 Charger wire 56UA2509# 2 750,000 3
11 Charger rubber vibration isolator 55VA2527# 2 750,000
12 Charger cleaning unit 55VA-255# 2 750,000 5
13 C-clip 45AA2040# 2 750,000
14 Developing Developing unit 56UA-300# 1 6,000,000 36
section
15 Developing suction assembly 56UA-325# 1 6,000,000 37
16 Suction filter 56UA3108# 1 750,000 6
17 Developer DV010 1 * 1,000,000
18 Agitator plate assembly /1 56UA-347# 1 1,500,000 153
19 Agitator plate assembly /2 56UA-348# 1 1,500,000 153
20 Toner supply Toner supply sleeve /1 55VA-334# 1 3,000,000 23
section
21 Toner supply sleeve /2 55VA-335# 1 3,000,000 24
22 Pump unit /Lt 56UA-780# 1 10,000,000 52
23 Pump unit /Rt 56UA-790# 1 10,000,000 51
24 Cleaning/ Cleaning blade 14RT56011F
56UA5351# 2 750,000 2
25 recycle sec- Toner seal board 56UA-568# 1 3,000,000 25
26 tion Toner guide brush assembly 56UA-574# 1 1,500,000 12
27 Scattering prevention felt 55VA5568# 1 1,500,000
28 Seal plate /Fr 56UA-559# 1 1,500,000 14
29 Seal plate /Rr 56UA-558# 1 1,500,000 13
*
The actual replacement cycle of the drum and developer is 1,000,000 prints or 220 hours of use, whichever is earlier.
2 31
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
No. Classification Part name Part number Qt. Actual Parts count No.
replacement
/1050e/1050eP
cycle
30 Cleaning/recy- Toner guide plate assembly 56UA-561# 1 3,000,000 26
31 cle section Cleaning gear /A assembly 56GA-556# 1 6,000,000 167
32 Cleaning gear /B 55VA7921# 1 15,000,000 172
33 Paper feed sec- Pick-up roller 55VA-484# 2 500,000 53,57
34 tion Paper feed roller 55VA-483# 2 500,000 54,58
35 Separation roller 55VA-483# 2 500,000 54,58
36 Paper feed clutch /1 56AA8201# 1 3,000,000 55
37 Paper feed clutch /2 56AA8201# 1 3,000,000 59
38 Separation clutch /1 56AA8201# 1 3,000,000 56
39 Separation clutch /2 56AA8201# 1 3,000,000 60
40 Vertical con- Conveyance roller /1 56UA4413# 1 6,000,000 82
41 veyance sec- Conveyance roller /2 56UA44141E 1 6,000,000 83
42 tion Conveyance roller /3 56UA44641E 1 6,000,000 83
43 Pre-registration roller /1 56UA44111E 1 6,000,000 84
44 Pre-registration roller /2 56UA44111E 1 6,000,000 85
45 Conveyance exit roller 56UA4412# 1 6,000,000 77
46 Paper dust guide brush assembly 55VA-574# 1 4,500,000 76
47 Pre-registration bearing 56UA7603# 4 6,000,000
48 Pre-registration clutch /1 56AA8201# 1 3,000,000 79
49 Pre-registration clutch /2 56AA8201# 1 3,000,000 81
50 Vertical conveyance clutch 56AA8201# 1 3,000,000 80
51 Paper dust guide brush gear assembly 56UA-478# 1 10,000,000
52 Transfer/sepa- Transfer/separation charger unit 56UA-270# 1 6,000,000 38
53 ration charger Discharge wire 56UA2613# 3 750,000 7
54 Transfer presser rubber 56AA1783# 3 750,000
55 Transfer cleaning assembly 56GA-276# 1 750,000 8
56 Separation cleaning assembly /1 56GA-277# 1 750,000 8
57 Separation cleaning assembly /2 56GA-278# 1 750,000 8
58 C-clip 45AA2040# 3 750,000
59 Transfer assist sheet assembly 56UA-281# 1 1,500,000 10, 11
60 TSL 55VA8308# 1 6,000,000 39
61 Registration Registration roller /Up 56UA46061E 1 6,000,000 40
62 section Registration bearing 56UA7602# 2 6,000,000 40
63 ADU section Paper exit roller /1 56UA47432E 1 6,000,000 44
64 Paper exit roller /2 assembly 56UA-035# 1 6,000,000
65 ADU accelerate roller 56UA4740# 1 6,000,000 41
66 Reverse/exit roller 56UA4741# 1 6,000,000 42
67 ADU reverse roller 56UA4741# 1 6,000,000 43
68 ADU conveyance roller /1 56UA47442E 1 6,000,000 45
32 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
69 ADU section ADU conveyance roller /2 56UA47442E 1 6,000,000 45
70 ADU conveyance roller /3 56UA4595# 1 6,000,000 45
71 ADU conveyance roller /4 56UA4683# 1 6,000,000 45
72 ADU exit roller 56UA4683# 1 6,000,000 45
73 Fusing exit roller 56UA4595# 4 6,000,000 46
74 Reverse gate 56UA4760# 7 10,000,000
75 Fusing sec- Cleaning web 56UA5351# 1 750,000 1
76 tion Fusing heater lamp /1 55VF8302#
55VB8302# 1 3,000,000
77 Fusing heater lamp /2 55VF8303#
56UA8303# 1 3,000,000
78 Fusing heater lamp /3 55VF8304#
55VB8304# 1 3,000,000
79 Fusing roller /Up 56UA5304# 1 1,500,000 15
56UA5470#
80 Heat insulating sleeve 45405339# 2 1,500,000 19
81 Fusing bearing /Up 45407504# 2 1,500,000 20
82 Heating roller bearing 56UA7507# 2 3,000,000 28
83 Fusing gear 56UA7783# 1 6,000,000 48
84 Fusing roller /Lw assembly 56UA-528# 1 1,500,000 16
85 Fusing heating roller 56UA5307# 1 3,000,000 31
86 Heat insulating sleeve /Lw 26AA5315# 2 3,000,000 27
87 Fusing claw /Up 56UA5453# 6 1,500,000 17
88 Fusing claw /Lw 25AA5329# 2 1,500,000 18
89 Thermistor /2 55VA8804# 1 3,000,000 29
90 Thermistor /4 55VA8806# 1 3,000,000 30
91 Fusing actuator 56UA5383# 1 6,000,000 50
92 Web motor 56GA8017# 1 6,000,000 49
93 Fusing cleaning sheet assembly 56UA-547# 1 1,500,000 21
94 Paper exit Main body paper exit roller 56UA45571E 1 6,000,000 47
section
33
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.4.2 Option
No. Classification Part name Part number Qt. Actual Parts count No.
replacement
/1050e/1050eP
cycle
1 DF Pick-up roller 13GA4604# 1 800,000 141
2 Paper feed roller 15AS4605# 1 800,000 142
3 Paper feed auxiliary roller 15AS4601# 1 800,000 144
4 Separation roller 13GA4606# 1 400,000 143
5 Torque limiter 13GA-135# 1 800,000 145
6 PF Pick-up roller 55VA-484# 3 500,000 61,66,71
7 Paper feed roller 55VA-483# 3 500,000 62,67,72
8 Separation roller 55VA-483# 3 500,000 62,67,72
9 Paper dust removing brush 15BY5604# 3 3,000,000
10 Paper feed clutch /1 56AA8201# 1 3,000,000 63
11 Paper feed clutch /2 56AA8201# 1 3,000,000 68
12 Paper feed clutch /3 56AA8201# 1 3,000,000 73
13 Separation clutch /1 56AA8201# 1 3,000,000 64
14 Separation clutch /2 56AA8201# 1 3,000,000 69
15 Separation clutch /3 56AA8201# 1 3,000,000 74
16 Forced separation clutch 56AA8201# 1 3,000,000 70
17 Pre-registration clutch /1 56AA8201# 1 3,000,000 90
18 Pre-registration clutch /2 56AA8201# 1 3,000,000 91
19 Pre-registration clutch /3 56AA8201# 1 3,000,000 92
20 Torque limiter 57GA4430# 2 6,000,000
21 Intermediate clutch /Up 56AA8201# 1 3,000,000 93
22 Intermediate clutch /Lw 56AA8201# 1 3,000,000 94
23 Pre-registration roller 15BA45071E 3 6,000,000 86,87,88
24 Bearing 56UA7603# 6 6,000,000
25 Conveyance roller 15BA45082F 4 6,000,000 86,88
26 PFU paper exit roller 15BA5011# 1 6,000,000 89
27 FD Pick-up rubber 50BA-574# 6 200,000 114,117
28 Paper feed rubber 50BA-575# 2 100,000 116,119
29 Separation rubber 13QN-443# 2 100,000 115,118
30 Roller solenoid /1 15AG-493# 1 5,000,000 121
31 Roller solenoid /2 15AG-493# 1 5,000,000 121
32 Roller solenoid /3 15AG-493# 1 5,000,000 122
33 Roller solenoid /4 15AG-493# 1 5,000,000 122
34 Punch motor 15AG-573# 1 5,000,000 120
35 Tray up down motor 129U-108# 1 5,000,000 123
36 LS Stacker tray up down motor 15AV8003# 1 5,000,000 128, 133
37 Paper press solenoid /1 15AV8252# 1 5,000,000 124, 129
38 Paper press solenoid /2 15AV8251# 1 5,000,000 126, 131
39 Paper press solenoid /3 15AV8255# 1 5,000,000 125, 130
34 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
40 LS Rear stopper solenoid 15AV8253# 1 5,000,000 127, 132
41 FS Intermediate roller release solenoid 15AA-449# 1 5,000,000 113
42 Stapler unit /Fr 15AA4222# 1 500,000 111
43 Stapler unit /Rr 15AA-450# 1 500,000 112
44 Paper exit roller /A (sponge roller) 122H4825# 8 750,000
45 SD Roller release solenoid /1 15AN8251# 1 5,000,000 139
46 Roller release solenoid /2 15AN-239# 1 5,000,000 140
47 Roller release solenoid /3 15AN8251# 1 5,000,000 140
48 Right angle gate solenoid 15AN-249# 1 5,000,000 138
49 Stapler assembly /Rt 15AN-550# 1 1,000,000 134
50 Stapler assembly /Lt 15AN-550# 1 1,000,000 135
51 Trimmer blade assembly 15AN-570# 1 37,500 136
52 Trimmer board assembly 15AN5282# 1 18,900 137
53 Trimmer blade motor 15AN8002# 1 200,000
54 Trimmer press motor 15AN8002# 1 200,000
55 Bundle press stage gear 15AN7719# 1 500,000
56 PB Switchback roller 13GQ4519# 1 750,000 158
57 Cover paper separation clutch 56AA8201# 1 3,000,000 162
58 Roller cutter blade Assy A0754421# 1 100,000 163
59 Filter A0753724# 1 750,000 164
60 Sub tray exit solenoid 15ANR714# 1 10,000,000 154
61 SC switchback release motor 13GQ8005# 1 6,000,000 155
62 FD alignment solenoid 15AA8251# 1 20,000,000 156
63 SC pressure arm solenoid A075B746# 1 20,000,000 157
60 RC Recycle pump 14RT-210# 1 10,000,000 151
61 Accumulator 14RT-230# 1 10,000,000 152
62 Waste toner recycle box 14RT-970# 1 750,000 150
(including the waste toner filter)
No. Classification Part name Part number Qt. Actual Parts count
replacement No.
cycle
1 PB Pick-up roller 55VA-484# 1 500,000 159
2 Paper feed roller 55VA-483# 1 500,000 160
3 Separation roller 55VA-483# 1 500,000 160
4 Cover paper pick up clutch 56AA8201# 1 3,000,000 161
5 PF (PP-701) Pick-up roller A08R5621# 1 50,000 61,66,71
6 Paper feed roller A08R5622# 1 50,000 62,67,72
7 Separation roller A08R5622# 1 50,000 62,67,72
2 35
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• When replacing periodically replaced parts, be sure to unplug the power cord of the main body
from the power outlet.
(2) Procedure
1. Loosen 2 screws [1] and remove the exhaust
[1] cover [2].
[2]
1050fs2053c
[3]
1050fs2054c
36
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Loosen 2 screws [1] and remove the filter cover
[2].
[1]
[2] 1050fs2055c
1050fs2056c
37
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When the drum section has been removed, be sure to store it in a dark place with the drum cover
provided.
• When removing/reinstalling the photo conductor section, be careful not to rotate the drum in any
direction other than the specified direction. Rotating it in the opposite direction to the rotational
direction while printing may cause damage to the cleaning blade.
• When removing/reinstalling the photo conductor section, be absolutely sure not to touch the drum
claw.
(1) Procedure
1. Open the front doors /Rt and /Lt.
[1]
2. Bring down lever A of the ADU.
(See P.112)
3. Loosen 3 screws [1] and remove the photo con-
ductor section cover [2].
[2]
1050fs2089c
[1]
1050fs2090c
38
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[1]
1050fs2091c
[4]
NOTE
• For reinstallation of the coupling, see "B.
Cleaning/reinstallation of the coupling" in the
next section.
39
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to conduct this operation when removing the photo conductor section.
(1) Procedure
1. Clean the periphery of the coupling with drum
[1]
cleaner.
2. Insert the coupling so that the protrusions [2] of
the coupling [1] get into the depressed portions
[2] [4] of the drum [3].
NOTE
• An detent [5] is provided on the inside of the
coupling [1]. So be sure to set it into the key
groove [7] of the drum shaft [6].
[4]
[7]
[3]
[6]
[2]
[5] fs503fs2094c
40
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
bearing [2].
[1] [2]
1050fs2420c
[2]
[1] 1050fs2095c
41
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• When removing the charger unit, be careful not to touch the mesh portion of the charger control
plate with bear hands.
• When cleaning the charger control plate, blow off dirt with the blower brush.
(2) Procedure
1. Pull the photo conductor section out of the main
body. (See P.38)
[3]
2. Disconnect the connector [1] and remove the
wiring harness of the charger from the harness
clamps [2] at the 3 places.
3. Hold the portions marked with [3] and [4] and
[2]
remove the charger unit [5].
4. Reinstall the above parts following the removal
steps in reverse.
[1]
[5]
[4]
1050fs2096c
42
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Remove the charger unit.
(See P.42)
2. Slide the lever [1] in the arrow-marked direction
[2] to release the lock [3] and remove the charger
[4] control plate [4].
NOTE
• Be sure to avoid loosening or removing the
screw [5] that fastens the lever.
[4] [5]
[1]
[2] 1050fs2104c
43
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Remove the charger unit. (See P.42)
[2] [5]
2. Remove the charger control plate. (See P.43)
3. Remove the spark arrester plates /Fr [1] and /Rr
[2].
4. Remove the springs [3], one each, and then
remove the charger wires [4] and the charger
vibration proof rubber [5], one each.
NOTE
• When reinstalling the charger wire, be sure to
insert each of the wires into the cut [6] of the
[6] charger vibration proof rubber.
[5] [4] • Be sure to reinstall the charger wires so that
the hook [7] of each spring turns to the inside.
[7] [1]
44
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• C-clip: Every 750,000 prints
(2) Procedure
1. Remove the charger unit.(See P.42)
[4]
2. Remove the charger control plate. (See P.43)
3. Remove the charger wire. (See P.44)
4. Remove the C-clip [3], one each, from the shaft
[3]
[2] of the charger cleaning unit [1].
[2] 5. Reverse the charger unit [4] and remove the 2
charger cleaning units.
6. Remove the collar [5] from the shaft of each of
the charger cleaning units.
7. When the charger back plate is stained, clean it
with drum cleaner and a cleaning pad.
[4]
[1] NOTE
• Be careful that the collar inserted into the
[6] shaft of the charger cleaning unit does not
drop off.
• Be sure to reinstall the charger cleaning unit
so that the marking "F" [6] turns in the same
direction as shown in the drawing.
[2]
[5] 1050fs2106c
1 45
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the photo conductor section.(See P.38)
2. Remove the charger unit. (See P.42)
[2]
3. Remove 2 connectors [1] and then remove the
wiring harness from the wiring harness clamp.
NOTE
• Take note of the direction of the connector to
be removed.
[1]
46
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
7. Reinstall the above parts following the removal
steps in reverse.
47
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be careful not to touch or damage the drum and the cleaning blade with bare hands.
• When storing the drum, be sure to store it in dark place with the drum cover attached.
• When reinstalling the drum, the cleaning blade and the toner guide brush, be sure to apply setting
powder all around the drum and the cleaning blade regardless of these parts being new or used
ones.
• When the drum is applied with setting powder, be sure to conduct the following operations before
installing the photo conductor section to the main body:
1) With the charger and the developing section removed, rotate the drum one full turn (to prevent
splashing of setting powder to the charger and prevent the image from getting blurred).
2) When installing a new drum, be sure to reset the photo conductor counter in the service mode.
If not reset, image fogging and toner splash may result.(See P.350)
(2) Procedure
1. Pull out the photo conductor section.
[1]
(See P.38)
2. Remove the charger unit.
(See P.42)
3. Remove the sensor support stay assembly.
(See P.46)
4. Remove the developing unit.
(See P.53)
5. Remove the cleaning section.
(See P.72)
6. Remove the drum [1].
1050fs2099c
48
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
gamma sensor [4] on the toner control sensor
board (TCSB) with a cleaning pad.
[3] [4]
NOTE
• When cleaning toner with a vacuum cleaner,
be sure to turn the shutter section [3] in the
arrow-marked direction.
• When cleaning the recycle pipe, be sure to tap
the pipe softly to let toner that adheres to the
inner wall drop off, and then rotate the gear
[4] to discharge the toner.
49
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• When reinstalling the drum claw, take note of the direction and position of the claw.
(2) Procedure
1. Pull out the photo conductor section.(See P.38)
[4] [3]
2. Remove the cleaning unit. (See P.72)
3. Remove the drum. (See P.48)
4. Disconnect the connector [1] and remove the
spring [2].
5. Remove 2 screws [3] and then remove the drum
claw unit [4].
50
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
unit to the guide hole [4] of the photo conduc-
tor section [3].
[4]
[3]
[4]
[2]
[1]
1050fs2102c
51
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
6. Remove the C-clip [1], pull out the shaft [2] in the
[3]
arrow-marked direction and remove the 3 drum
claws [3].
/1050e/1050eP
[5] 1050fs2103c
52
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Suction filter: Every 750,000 prints
(2) Procedure
1. Pull the photo conductor section out of the main
[2]
body.
(See P.38)
2. Open the cover of the developing suction assem-
[1]
bly [1].
3. Remove the suction filter [2].
4. Clean the outside and the inside of the develop-
ing suction assembly with the cleaner.
NOTE
• When reinstalling the suction filter, be sure to
expand the filter opening before installation.
1050fs2107c
• When reinstalling it, make sure that the cover
of the developing suction assembly has been
closed thoroughly.
(2) Procedure
1. Pull the photo conductor section out of the main
body.
(See P.38)
2. Remove the screw [1] and then remove the
developing suction assembly [2].
[2] 3. Reinstall the above parts following the removal
steps in reverse.
[1] 1050fs2108c
53
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
body.
(See P.38)
2. Remove the developing suction assembly.
(See P.53)
3. Remove the developing unit.
(See P.55)
4. Remove the developing unit cover /1.
(See P.55)
5. Clean up the developer regulation blade [1], the
[3] underside of the developing roller [2] and both
[3] [2] 1050fs2401c
sides of the developer roller [3] with a vacuum
cleaner.
NOTE
• Be careful not vacuum too much developer
necessarily. Cleaning should be restricted
only to stained sections.
• Be careful not to bend the lower sheet.
[2]
1050fs2402c
54 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull the photo conductor section out of the main
body.
(See P.38)
2. Remove the developing suction assembly.
(See P.53)
3. Release the developing pressure lever [2] while
holding down the right side [1] of the developing
unit.
NOTE
• When releasing the developing pressure lever,
[2] [1] 1050fs2109c
be careful not to touch the front panel and the
rear panel of the photo conductor section.
4. Hold the sections [1] and [2] with both hands and
remove the developing unit [3].
[2]
[1]
[3]
1050fs2110c
55
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the developer unit, make
sure that the developing unit stopper roller [1]
/1050e/1050eP
[1] [1]
1050fs2116c
[2] NOTE
• When reinstalling the developer unit, be care-
ful that the front panel of the photo conductor
section does not come into contact with the
developing roller [1].
[1] 1050fs2111c
• Never rotate the developing gear to the
arrow-marked direction [2].
56 1
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
[2]
1050e/1050eP
• When replacing the developer, be careful that
dirt does not get into it.
• When rotating the developing roller [1], be
sure to rotate the developing gear to the
arrow-marked direction [2] with the flat blade
driver.
• When putting in new developer, be sure to
reset the developer counter in the service
mode. If not reset, image fogging and toner
[1] splash may result. (See P.350)
1050fs2112c
(2) Procedure
1. Pull the photo conductor section out of the main
[4] body.
[2]
(See P.38)
2. Remove the developing suction assembly.
(See P.53)
[3] 3. Remove the developing unit.
(See P.55)
[1] 4. Release 2 hooks [1] and remove the developing
1050fs2113c
unit cover /1 [2].
5. Release 2 hooks [3] and remove the developing
unit cover /2 [4].
1 57
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• Any used developer remaining in the develop-
ing roller may cause gray background to the
image.
[3]
1050fs2114c
58 1
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
1. Open the toner supply door [1] and pull out the
[3]
toner supply cover /A assembly [2].
2. Remove the toner bottle [3].
[1]
[2] 1050fs2004c
1050fs2005c
59
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Open the front doors /Rt and /Lt.
[2]
2. Bring down the lever A of the ADU.(See P.112)
3. Remove the cover on the photo conductor sec-
tion and pull out the intermediate toner hopper to
open it.(See P.38)
4. Close up the connection opening [1] of the inter-
mediate toner hopper with a cleaning pad [2].
5. Attach the toner recovery bag [4] beneath the
shutter section [3] connected to the developing
unit.
NOTE
• For the toner recovery bag, use a paper bag
made by folding a sheet of paper, or a vinyl
bag. Be sure to fix it at an appropriate place
so that toner does not spill over. And also,
[3] [4] [1] 1050fs2783c
make sure that the bag does not come down
by the toner's own weight.
• The intermediate toner hopper contains toner
about half as much as the volumetric capacity
of the hopper. Be sure to set up a bag that
accommodates of the entire toner amount.
NOTE
• While discharging, be sure to rotate the gear
[2] several times in the arrow-marked direc-
tion [3] once in a while so that toner that is
above the agitator plate assembly is dis-
charged.
• When rotating the gear [2] and no more toner
is discharged, it is considered that almost all
toner has been recovered.
• Be sure to avoid sucking toner in the interme-
[1] [6] 1050fs2784c
diate toner hopper with a vacuum cleaner.
Using a cleaner may cause damage electro-
statically to the toner remaining sensor /1
(PS31).
60 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
arrow-marked direction [3].
NOTE
• The intermediate toner hopper cover assem-
bly [5] will also be adhered with toner. Be
careful that it does not scatter.
[3] 1050fs2802c
NOTE
• At this time, the sheet of the agitator plate
assembly /1 jumps up. Be sure to cover about
half of it with paper so that toner does not
scatter.
NOTE
[5] [3] [4] 1050fs2785c
• Be sure not to rotate the gear [1] after remov-
ing the agitator plate assembly /1. Rotating it
may cause a phase lag with the agitator plate
assembly /2 [5], thus making it impossible to
detect the remaining amount of toner prop-
erly.
2 61
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12. Remove the two screw [1] and remove the stir-
[2]
ring plate /2 assembly [2].
13. Reinstall the above parts following the removal
/1050e/1050eP
steps in reverse.
NOTE
• The recovered toner may get mixed with
impurities. Be sure to dispose of it, do not put
it back in the intermediate toner hopper.
[1]
1050fs5101c
62 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Toner supply sleeve /2: Every 3,000,000 prints
(2) Procedure
1. Remove the left cover.(See P.250)
[1] 2. Open the front doors /Rt [1] and /Lt [2] and the
toner supply door [3].
3. Remove the toner bottle [4]. (See P.59)
[2] 4. Remove the toner supply door. (See P.254)
5. Replace the toner supply cover /A assembly [5].
[4]
[3]
[5] 1050fs2006c
NOTE
• If the toner supply cover /A assembly [3] is
set, the lock section [5] remains in contact
when the toner supply lock assembly [4] is
removed. Be sure to pull out the toner supply
cover /A assembly [3].
63
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1] 1050fs2008c
NOTE
• Keep each of the released hose clamps [1]
near the connecting opening of each hose [3].
• When the hose [3] is removed from the toner
feed case [2], toner may spill out of each
hose. Be careful that the inside of the main
body does not get stained with toner.
• The hose connecting section of the toner feed
case [2] and the hose [3] are provided with the
[3] toner supply installation label [4] that indi-
cates the respective points to which a con-
[1] [3] nection is made. When installing each hose,
be sure to make a connection between the
points having the corresponding toner supply
installation label [4].
[2] 14. Release the cable clamp [5] and pull out the hose
[3] to the outside of the main body.
NOTE
• The hose [3] may be damaged when the toner
supply unit [6] is being removed. Be sure to
[4] [4] 1050fs2009c
pull it out to the outside of the main body.
64
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[3] 1050fs2010c
NOTE
[1]
• When reinstalling the toner supply unit [1], be
sure to insert 2 guide pins [2] on the rear side
[4] and 2 guide pins [3] on the front side into the
respective guide holes [4] of the main body
frame.
[3]
[1]
[4]
[2] 1050fs2011c
65
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[1]
[2]
[1]
1050fs2012c
[1]
[2]
[1]
1050fs2404c
66
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
tioning hole [3] of the cover /Up [2] and then
insert the projection [6] of the cover /Up [2]
into the slit [8] of the drive board [7].
[7]
[2]
[4]
[3]
[5]
[2]
[3]
[4] [5]
1050fs2013c
67
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
[1]
[2] 1050fs2014c
NOTE
[1] [2]
• Be sure to reinstall the toner supply sleeves /1
[1] and /2 [2] in the direction as shown in the
drawing.
NOTE
• After completion of disassembly/assembly of
the toner supply unit, be sure to select the
code 54-09 (rotation of the toner pump motor
(M28) and the air pump motor (M29)) in the I/O
check mode of the service mode and then
press the start button.
When toner drops off into the mixing section
due to the vibration of the disassembly/
assembly, this may cause the codes SC23-14
and SC23-17. (See chapter III "4.6.1 G.
Removing toner from the toner mixing sec-
tion" in the Field Service for the main body.)
68
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Pump unit /Rt: Every 10,000,000 prints
(2) Procedure
1. Remove the rear cover and the upper covers /
Rr1 and /Rr2.(See P.250)
2. Remove 4 screws [1] and then remove the exte-
rior mounting plate [2].
[1]
[2]
[1] 1050fs2016c
69
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• Keep each of the released hose clamps [2]
near the connecting opening of each hose [4].
• When the hose [4] is removed from the pump
unit /Rt [3], the toner may spill out of each
hose. Be careful that the inside of the main
body does not get stained with the toner.
• The hose connecting section of the pump unit
/Rt [3] and the hose [4] are provided with the
toner supply installation label [5] that indi-
cates the respective points to which a con-
[5] nection is made. When installing each hose,
[5] [4] 1050fs2017c
be sure to make a connection between the
points having the corresponding toner supply
installation label [5].
NOTE
• Keep each of the released hose clamps [2]
near the connecting opening of each hose [4].
• When the hose [4] is removed from the pump
unit /Lt [3], the toner may spill out of each
hose. Be careful that the inside of the main
body does not get stained with the toner.
• The hose connecting section of the pump unit
/Lt [3] and the hose [4] are provided with the
toner supply installation label [5] that indi-
cates the respective points to which a con-
nection is made. When installing each hose,
[5] [4] [5] 1050fs2405c
be sure to make a connection between the
points having the corresponding toner supply
installation label [5].
70
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[2] NOTE
[1]
• When reinstalling each pump unit, be sure to
[1] insert the toner supply spacer [4] between the
attaching surfaces.
71
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• Be sure to avoid touching the edge of the cleaning blade with bare hands.
• Before reinstalling the cleaning section, be sure to clean the cleaning section with a blower brush
and a cleaning pad.
• When reinstalling the cleaning section, be sure to apply setting powder to the entire periphery of
the drum and the cleaning blade regardless of these parts being new or used ones.
• When the drum is applied with setting powder, be sure conduct the following operations before
installing the photo conductor section to the main body:
1) To obtain an accurate toner density, clean setting powder splashed onto the gamma sensor
and the maximum density sensor on the toner control sensor board (TCSB) with a cleaning pad
soaked in drum cleaner.
2) With the charger unit and the developing unit removed, rotate the drum one full turn (for splash
prevention of setting powder to the charger and prevention against the image getting blurred).
(1) Procedure
1. Rotate the drum one full turn by hand.
NOTE
• Be sure to rotate the drum one full turn to pre-
[7]
vent the toner on the guide brush inside the
cleaning section from falling down.
[6] 1050fs2117c
72
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• When replacing the cleaning blades, be sure to replace 2 blades at the same time.
• Be sure to avoid touching the edge of the cleaning blade with bare hands.
(2) Procedure
1. Pull the photo conductor section out of the main
body. (See P.38)
2. Remove the cleaning section. (See P.72)
[1] 3. Remove the screw [1] and then remove the
cleaning blade /2 [2].
4. Reinstall a new cleaning blade /2.
[2] 1050fs2119c
73
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
NOTE
• Be sure to keep the blade release arm raised
[1] up, do not let go of it.
[3]
[4]
1050fs2120c
74
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
[1]
• Be sure to keep hold of the blade replacement
lever [3] being rotated, do not let go of it.
[2]
[3]
1050fs2121c
[4]
75
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• After replacing the cleaning blades /1 and /2,
be sure to check to see if the blade replace-
ment lever [1] has been pulled.
• After replacing the cleaning blades /1 and /2,
be sure to conduct the blade set mode in the
service mode to prevent the blade from curl-
ing up.(See P.346)
• Be sure to avoid using the blade set mode
other than when replacing the cleaning blade.
[1] fs503fs2153c
Otherwise, the cleaning blade count of the
fixed parts count is reset so that the blade is
not replaced automatically at the correct tim-
ing.
76
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• Be sure to avoid touching the edge of the cleaning blade with bare hands.
(3) Procedure
1. Pull the photo conductor section out of the main
[4] [6] [5]
body. (See P.38)
2. Remove the cleaning section. (See P.72)
3. Remove the screws [1] and [2], and then remove
the toner seal board [3].
4. Clean the sheet section [4] of the toner seal
[3] board with a blower brush and a cleaning pad.
NOTE
• When reinstalling the toner seal board, be
sure to first of all install the screw [1].
• When both sides [5] of the sheet section of
the toner seal board get inside of the toner
guide brush [6], an overflow toner may result.
On such an occasion, a correction should be
made so that the warp of the sheet section
[2]
[1] [3] 1050fs2122c
becomes parallel to the toner guide brush or
it turns a little to this side (less than 1 mm).
77
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to avoid touching the edge of the cleaning blade with bare hands.
• When reinstalling the toner guide brush, apply setting powder uniformly with the toner guide brush
removed.
• Be absolutely sure to avoid touching the brush section of the toner guide brush with bare hands.
Also, be careful that the brush section does not come in direct contact with other objects.
(2) Procedure
1. Pull the photo conductor section out of the main
[2]
body. (See P.38)
2. Remove the cleaning section. (See P.72)
3. Remove the toner seal board.(See P.77)
4. Remove the screw [1] and then remove the seal
plate /Fr [2].
5. Remove the screw [3] and then remove the seal
plate /Rr [4].
[1]
[4]
[3]
1050fs2118c
78
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When reinstalling the toner guide brush, be
sure to set the pin [6] of the toner guide brush
to the coupling slit [5] of the cleaning section
[6] [4].
[4] [3]
[5] 1050fs2123c
79
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
[1]
• Be careful that the toner prevention collar
does not get lost.
[4]
[7]
1050fs2124c
80
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Cleaning gear /B: 15,000,000 prints
• Toner guide plate assembly: Every 3,000,000 prints
(2) Procedure
1. Pull the photo conductor section out of the main
[2] body. (See P.38)
2. Remove the cleaning section. (See P.72)
[5] [1] 3. Remove the toner seal board. (See P.77)
4. Remove the seal plate. (See P.78)
5. Remove the E-rings [1], one each, and then
remove 2 cleaning mounting lever collars [2].
6. Remove the screws [3] (B tight M3 x 8) and [4]
[4]
(TPM3 x 6) and then remove the drive reinforcing
plate [5].
[1] 1050fs2423d
2 81
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• While removing the cleaning gear /A assembly
or the cleaning gear/B [3], the bearing [4] and
the splash prevention felt [5] may come off. If
the felt become detached, make sure to
replace it with a new one.
1050fs2424d
1050fs2425d
1050fs2426d
82 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
outside so that the bearing [1] does not come
off.
• If the bearing and the splash prevention felt
[2] become detached while inserting the toner
guide shaft, make sure to replace the splash
prevention felt with a new one.
1050fs2427d
2 83
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the toner guide plate
assembly, be sure to hit it against the lower
side before fixing it.
[2]
[1] 1050fs2130c
84
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• When removing the cleaning unit, be sure to clean thoroughly both the inside and the inner wall of
the cleaning unit and the recycle pipe with as little toner left as possible. When cleaning is insuffi-
cient, toner may spill over the conveyance section.
(1) Procedure
1. Pull out the photo conductor section from the
main body. (See P.38)
2. Remove the cleaning section.(See P.72)
3. Remove the toner seal board.(See P.77)
4. Remove the toner guide brush/seal plates Fr and
Rr.(See P.78)
5. Tap the casing [1] section softly to let the recy-
cled toner adhering to the inner wall drop off.
[1] 1050fs2431c
[1] 1050fs2432c
NOTE
• When cleaning it with a vacuum cleaner, be
[1] [2] 1050fs2433c
careful that the vacuum cleaner does not
come into contact with drum.
85
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• The pick-up roller assembly/separation roller assembly are CMS corresponding parts.
(1) Procedure
NOTE
• The method for replacing the pick-up roller assembly/separation roller assembly is the same for
tray /1 and tray /2. The explanation here is given for tray /1.
• After completion of the installation, rotate the pick-up roller in the direction of the paper feed
(counterclockwise as seen from the front) to check to see if the paper feed roller, the belt and the
coupling section rotate smoothly. The rotation of the pick-up roller is restricted only to the direc-
tion of the paper feed (counterclockwise as seen from the front) and be absolutely sure not to turn
it clockwise.
• Be sure to take note that the direction of the pick-up roller is different for the main body and the
PF.
[1]
1050fs2700c
86
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
nal direction.
[1]
NOTE
• The rotation of the pick-up roller [1] is
restricted only to the arrow-marked direction
(counterclockwise). It does not rotate in the
reverse direction (counterclockwise). So, be
sure not to turn it in this direction forcibly.
1050fs2701c
NOTE
• When installing the bearing /Fr [1], /Rr [2],
insert it in the notch [5] of the metal frame
while pressing down a little the metal frame
[1]
[3] of the pick-up roller assembly to make
level the flat portion [4] of the bearing /Rr [2].
And then insert the bearing /Fr [1] in the same
manner as with the bearing /Rr.
[4]
[5]
[2]
[3]
1050fs2702c
87
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When removing the pick-up roller [1], be care-
ful not to damage the sensor [7] with the
metal frame [6].
[5] [3]
[6]
[4]
88
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[2]
[1]
[3]
1050fs2704c
[1] 1050fs2705c
89
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1] 1050fs2706c
NOTE
• After completion of the installation, hold the
[1]
pick-up roller lightly and rotate it in the direc-
tion of the paper feed (counterclockwise as
seen from the front) to check to see if the
paper feed roller, the belt and the coupling
section rotate smoothly. (The rotation of the
pick-up roller is restricted only to the direc-
tion of the paper feed (counterclockwise as
1050fs2707c
seen from the front) and be absolutely sure
not to turn it clockwise.)
90
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Paper feed roller: Every 2,250,000 prints (actual replacement cycle: every 500,000 prints)
(2) Procedure
NOTE
• The outward appearance of the collar is identical for the paper feed roller and the separation roller.
However, a one-way mechanism is provided on the inside of the collar of the paper feed roller with
no mechanism provided for the separation roller. Be careful not to confuse one with the other.
[2]
3. Pull out the shaft [3] from the collar [1] and
remove the pick-up roller [2] from the collar [1].
NOTE
• When reinstalling it, take note of the direction
of the pick-up roller. Be sure to insert the col-
lar [1] from the side provided with the groove
[4].
[4]
1050fs2709c
91
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
4. Remove the C-clip [1] and pull out the collar [2]
[2] [3]
and the paper feed roller [3].
/1050e/1050eP
NOTE
• When reinstalling it, take note of the direction
of the paper feed roller. Be sure to insert the
collar [2] from the side provided with the
groove [4].
[4] [3]
[2]
1050fs2710c
92
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
NOTE
• The outward appearance of the collar is identical for the separation roller and the paper feed roller.
However, a one-way mechanism is provided on the inside of the collar of the paper feed roller with
no mechanism provided for the separation roller. Be careful not to confuse one with the other.
[3]
[2] 1050fs2711c
3. Pull out the gear [2], the collar [3] and the separa-
[1] [4] [5] [3] [2]
tion roller [4] from the shaft [1] in the arrow-
marked direction and remove them.
NOTE
• When reinstalling it, take note of the direction
of the separation roller. Be sure to insert it
into the shaft [2] from the side provided with
the groove [5].
• The outward appearance is identical for the
collar [6] of the separation roller and the col-
[6] [7] lar [7] of the paper feed roller. However, the
one-way mechanism is provided on the inside
of the collar [7] of the paper feed roller with
[8] no mechanism provided for the collar [6] of
the separation roller. Be careful not to con-
fuse one with the other.
1050fs2712c
93
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• The tray is heavy. Be sure to conduct this operation with two people.
NOTE
• The procedure for removing/reinstalling the trays /1 to /2 is identical. The explanation here is made
of the tray /1.
• When raising up the tray, be sure to hold it at the specified positions. Holding it at positions other
than those specified may cause damage to the tray, thus resulting in a paper feed jam.
(1) Procedure
1. Open the toner supply door.
2. Lightly raise up the tray lock lever [1] and pull out
the tray [2].
[1]
1050fs2715c
94
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[2]
1050fs2716c
95
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When raising up the tray, be sure to hold it at
the specified positions [3] and raise it up with
two persons.
• Be absolutely sure to avoid holding it at posi-
tions [4] that can be easily deformed. This
may affect the paper tray, thus resulting in a
[3] [1] jam.
• When reinstalling it, be sure to check to see if
the knobs [5] provided at the 4 places on the
rail are securely in the notches [6] of the tray.
96
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
prints)
• Separation clutch /1 (CL5), /2 (CL7): Every 15,000,000 prints (actual replacement cycle: every 3,000,000
prints)
1050fs2713c
NOTE
[6]
[5] • When reinstalling it, be sure to engage the
[6] stopper [6] of the clutch with the stopper sec-
tion [7].
[7]
[1] 1050fs2714c
97
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• The roller may get stained with paper dust
that has gathered in the paper dust guide
[4] holder [2]. Be sure to remove it when remov-
[4] ing the vertical conveyance unit.
NOTE
• When placing the vertical conveyance unit, be
sure to place it with the jam open/close door
side down. Placing it with the roller side down
1050fs2732c
may cause damage to the gear [6]. When
placing it with the roller side down, be sure to
remove 2 gears [6].
NOTE
• Pulling out the main body tray with the verti-
cal conveyance unit removed may damage
the guide roller that brings down forcibly the
pick-up roller of the main body tray. Be abso-
lutely sure not to pull out the main body tray
with the vertical conveyance unit removed.
• When reinstalling it, be sure to move the verti-
cal conveyance unit [5] to the rear side and
tighten it up with the screws [4].
98
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
prints)
• Vertical conveyance clutch (CL2): Every 4,500,000 prints (actual replacement cycle: every 3,000,000 prints)
(2) Procedure
1. Remove the right cover.
[2] 2. Remove the vertical conveyance unit. (See P.98)
3. Remove 2 C-clips [1] and then remove 2 gears
[2].
NOTE
• When reinstalling it, take note of the direction
of the gears.
[1]
1050fs2733c
NOTE
• When reinstalling it, set the stopper [7] of the
[8] [7] [1] [2] clutch to the screw [8].
1050fs2734c
99
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
C. Replacing the pre-registration roller /1, /2, the registration bearing and the conveyance rollers /2
and /3
(1) Periodically replaced parts/cycle
/1050e/1050eP
• Pre-registration roller /1 and /2: Every 10,000,000 prints (actual replacement cycle: every 6,000,000 prints)
• Pre-registration bearing /1 and /2: Every 10,000,000 prints (actual replacement cycle: every 6,000,000 prints)
• Conveyance roller /2: Every 10,000,000 prints (actual replacement cycle: every 6,000,000 prints)
• Conveyance roller /3: Every 10,000,000 prints (actual replacement cycle: every 6,000,000 prints)
(2) Procedure
1. Remove the right cover.
[4] [2] [6] 2. Remove the vertical conveyance unit.(See P.98)
3. Remove the pre-registration clutches /1 (CL1)
[4]
[5] and /2 (CL3) and the vertical conveyance clutch
(CL2). (See P.99)
4. Disconnect 2 connectors [1] and the connector
[2], and remove the wire binding bands [3] at the
[3] 5 places.
5. Remove 4 screws [4] (one each at either side of
each roller) and then remove the roller covers /1
[5] and /2 [6].
[7] [3] [1]
NOTE
[8] • Be careful that no damage is caused to the
sensor.
• When removing the roller covers /1 [5] and /2
[9] [6], be sure to pull up the upper side.
• When reinstalling the roller covers /1 [5] and /
2 [6], be sure to set the grooves at both sides
to the projection [8] and then press it lightly in
the direction of the paper through slit [9].
1050fs2735c
100
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
/2 [4].
NOTE
[3] • When removing and reinstalling the pre-regis-
tration rollers /1 [3] and /2 [4], be careful that
they are not damaged by the corners of the
guide plate.
[1] • When reinstalling the bearing [2], be sure to
raise the conveyance guide plate so that it is
in the jam release condition.
[2]
1050fs2736c
[1] 1050fs2738c
101
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[4]
[3]
[2]
[1]
1050fs2739c
NOTE
• After completion of the installation, check to
see if each roller rotates smoothly.
[3]
[1]
[2]
1050fs2740c
102
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Remove the right cover.
2. Remove the vertical conveyance unit. (See P.98)
3. Remove the E-ring [1] and then remove the gear
[2] and the pin [3].
[1] NOTE
• When installing the E-ring [1], be careful not
to damage the teeth of the gear [2].
[2] [3]
1050fs2741c
103
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When removing and reinstalling the convey-
ance roller /1 [4], be careful that it does not
get damaged by the corners of the guide
plate.
[1] • When reinstalling the bearing [3], be sure to
raise the conveyance guide plate so that it
gets into the jam release condition.
[3]
5. Reinstall the above parts following the removal
steps in reverse.
[2]
NOTE
• After completion of the installation, check to
see if the roller rotates smoothly.
[3]
[2]
[1]
1050fs2742c
104
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Paper dust guide brush gear assembly: Every 10,000,000 prints (actual replacement cycle: every 6,000,000 prints)
(2) Procedure
1. Remove the right cover.
[2]
2. Remove the vertical conveyance unit. (See P.98)
3. Remove 4 screws [1] and then remove the cover [2].
[1]
[1]
1050fs2743c
4. Remove the E-ring [1] and then remove the gear [2]
and the pin [3].
[3]
[2]
[1]
1050fs2744c
2 105
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2] NOTE
[1]
• When installing the bearing [3], be sure to
install it from the inside to the gear cover [2].
[3]
1050fs2745c
NOTE
• The gear removed at the step 4 is different
[3]
from the one removed at the step 6. Be care-
ful not to confuse one with the other.
[2]
[2] [1]
1050fs2746c
106
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
1050fs5103c
8. Remove the E-ring [1] and then remove the gear [2]
[2] [3]
and the pin [3].
[1]
1050fs2747c
2 107
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
1050fs2748c
108
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When taking out the conveyance exit roller
[4], the bearing [6] of the paper dust guide
brush assembly [5] is displaced. When rein-
stalling it, be sure to get it back to the original
place.
[4] [5]
[6]
[6] 1050fs2749c
109
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull the knob [1] and remove the paper dust
[1]
guide holder [2].
[2]
1050fs2750c
[2] [3]
2. Remove the screw [1] and pull out the holder [2]
from the shaft [3] of the paper dust guide brush.
[1]
1050fs2751c
110
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
and the bearing [4].
4. Reinstall the above parts following the removal
[3]
steps in reverse.
[4] 1050fs2752c
1050fs2753c
111
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3.5.8 ADU
A. Pulling out/reinstallation of the ADU
/1050e/1050eP
Caution:
• Be absolutely sure to avoid forcibly turning ON the interlock switches /1 (MS1) and /2 (MS2) with
the ADU pulled out. Otherwise, a high voltage may unexpectedly develop.
(1) Procedure
1. Open the front door /Rt [1] and the front door /Lt
[2] [1] [2].
2. While pressing the lock release lever [3] with a
driver in the arrow-marked direction, pull out the
ADU and bring the lever [4] down to pull out the
ADU section [5].
3. When reinstalling it, push in the ADU and bring
up the lever that pulls out the ADU section.
[5] [4]
[3]
1050fs2001c
112
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[3] 2. After sliding once the paper dust removing lever
[1] in the arrow-marked direction [2], pull out and
remove the paper dust removing brush [3] for the
registration roller /Lw.
(The picture shows the lever that has been pulled
[2] out a little.)
NOTE
• When reinstalling the paper dust removing
brush for the registration roller /Lw, be sure to
insert it fully until it hits against the back.
[1] 1050fs2131c
When the paper dust removing brush for the
registration roller /Lw is not inserted fully, this
may block the light path of detection of the
registration sensor (PS40), thus resulting in a
jam.
[2] fs503fs2132c
113
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
C. Cleaning of the paper dust removing brush for the registration roller /Up
(1) Periodic cleaning cycle
• Paper dust removing brush for the registration roller /Up: Every 750,000 prints
/1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2] [3] 2. Push out the projections [1], two each, and
release the lock to remove 2 paper dust remov-
ing brushes /1 [2] and /2 [3] for the registration
roller /Up.
[3]
[1] 1050fs2133c
[2] fs503fs2134c
114
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[1] [2]
2. Remove 2 screws [1] and release the fixing of the
sensor mounting piece [2].
fs503fs2135c
[1] fs503fs2136c
115
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
[1] 1. Pull out the ADU from the main body. (See P.112)
2. Remove the screw [1] and then remove the con-
nector cover [2].
[2]
1050fs2019c
NOTE
• When the transfer/separation charger unit is a
PCS corresponding part (See "6.5 PCS corre-
sponding parts"), remove also the connector
[2].
[4]
[3]
116
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
2. Remove the screw [1] and then remove the lever
[2] that pulls out the ADU section.
[6] 3. Loosen 2 screws [4] and remove the ADU cover /
Lt [5].
[4]
4. Loosen 2 screws [6] and remove the ADU cover /
Rt [7].
5. Reinstall the above parts following the removal
steps in reverse.
[5]
[7]
[3]
[1] [2]
1050fs2023c
117
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1] fs503fs2138c
[1]
[1]
[1] 1050fs2139c
118
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
7. Reinstall the above parts following the removal
steps in reverse.
[2] NOTE
• Reinstall the registration section so that it
comes to the same graduation as that used
for removal.
[3]
[2] 1050fs2140c
1 119
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2] [1] [1]
2. Remove the transfer/separation charger unit.
(See P.116)
3. Release the locks [1] at the 6 places and remove
[5] the plunging prevention plates /1 [2] and /2 [3].
4. Remove the spark arrester plates /Fr [4] and /Rr
[4] [5].
[1]
120
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When reinstalling the discharge wire, be sure
to insert each wire into the notch [4] of each
of the transfer presser rubbers.
• Reinstall the discharge wire so that the hook
[5] of each spring turns to the inside.
[3]
[4]
[2]
[3]
1050fs2147c
121
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
I. Replacing the transfer cleaning assembly/separation cleaning assemblies /1 and /2 and C-clips
(1) Periodically replaced parts/cycle
• Transfer cleaning assembly: Every 750,000 prints
/1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2]
2. Remove the transfer/separation charger unit.
(See P.116)
3. Remove the discharge wire. (See P.120)
4. Remove 3 C-clips [2] from the shaft [1] of each of
[1]
the cleaning assemblies.
[3] 5. Turn over the transfer/separation charger unit [3]
and remove the transfer cleaning assembly [4]
and the separation cleaning assemblies /1 [5]
and /2 [6].
6. Reinstall the above parts following the removal
steps in reverse.
[4]
[5]
[6] 1050fs2148c
122
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2]
2. Remove the transfer/separation charger unit.
(See P.116)
3. Remove 2 screws [1] and then remove the trans-
fer assist sheet assembly [2].
[1] 1050fs2149c
123
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
[2]
• When reinstalling the transfer assist sheet
assembly [1], make sure that the projections
/1050e/1050eP
[5]
[4] 1050fs2406c
124
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body.(See P.112))
2. Remove the transfer/separation charger unit.
(See P.116)
3. Remove the ADU cover.(See P.117)
4. Remove 4 screws [1] and then remove the trans-
fer exposure cover [2].
5. Remove the connector [3] and then remove the
TSL [4].
6. Reinstall the above parts following the removal
steps in reverse.
[1]
[4] [2]
125
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Remove the paper dust removing brush for the
registration roller /Lw. (See P.113)
3. Remove the paper dust removing brush for the
registration roller /Up. (See P.114)
4. Remove the registration section.(See P.118)
5. Remove the screw [1] and then remove the knob
[2].
[3] [4] 6. Remove 2 screws [3] and then remove the gear
[4].
[1]
[2] 1050fs2150c
126
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[1]
[1] 1050fs2151c
127
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[11] [10]
[4]
[3]
[7]
[6]
[5] 1050fs2152c
128
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• ADU conveyance roller /2: Every 6,000,000 prints
• ADU conveyance roller /3: Every 6,000,000 prints
• ADU conveyance roller /4: Every 6,000,000 prints
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
[1]
2. Remove the ADU cover.(See P.117)
3. Remove the registration section.(See P.118)
4. Disconnect the connector [1].
5. Remove 3 screws [2] and then remove the regis-
tration cooling fan (FM17) [3].
129
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[1] 1050fs2156c
[1] 1050fs2157c
130
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[1]
[2]
[3]
[4]
1050fs2158c
131
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[4]
[3]
1050fs2159c
132
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
ing [5].
15. Pull out the ADU exit roller [6] and remove it.
NOTE
[6]
• The roller is provided with one E-ring. Be sure
to remove also this E-ring when replacing the
roller.
[1]
[2]
[4]
[5]
133
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• Each roller is provided with one E-ring. Be
sure to remove also this E-ring when replac-
ing the roller.
[2] [1]
[3]
[4]
[6]
[8]
134
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[4]
[4]
[1] [2]
[3] 1050fs2162c
135
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
23. Remove 5 E-ring [2], the gear [3], the pin [4] and
[7]
the bearing [5] and [6] from the ADU conveyance
roller /2 [1].
/1050e/1050eP
NOTE
[2]
• When reinstalling the bearing [6], be sure that
[6] the flange [7] turns outside.
[1]
[3]
[2]
[4]
[2]
136
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• ADU conveyance roller /1: Every 6,000,000 prints
• ADU reverse roller: Every 6,000,000 prints
• Reverse/exit roller: Every 6,000,000 prints
• ADU acceleration roller: Every 6,000,000 prints
• Paper exit roller /1: Every 6,000,000 prints
• Paper exit roller /2 assembly: Every 6,000,000 prints
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
[1] 2. Remove the fusing section.(See P.153)
3. Open the paper reverse/exit section [1].
4. Remove the connector [2].
[3] 5. Remove the connectors [4] and [5], 16 pcs in all,
that are connected to the ADU drive board /1
[2] (ADUDB1) [3].
NOTE
• It is not necessary to remove the connector
[4] [5] [8] [7] of the ADU cooling fan /1 (RM15) [6].
• It is possible to remove the connector [8] on
the wiring harness side instead of removing
the connector [5].
[4]
[6] [4] [7] [4] [4] [4] 1050fs2189c
137
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the stay, be sure to set the
projection [4] of the ADU to the positioning
hole [3].
[2]
[1] 1050fs2190c
138
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When reinstalling the ADU acceleration motor
assembly, be sure to set the projection [4] of
the ADU to the positioning hole [3].
[3]
[4]
[2]
[1]
139
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the thick paper assist sole-
noid assembly, be sure to set the projection
[4] of the ADU to the positioning hole [3].
[1]
[6] NOTE
• When setting the belt, the tension is automat-
[7] ically adjusted by the spring [5]. Be sure to
[8] tighten up the screw [1] after the belt has
been set.
NOTE
• When reinstalling the ADU reverse motor
assembly, be sure to set the projection [8] of
the ADU to the positioning hole [7].
[1]
140
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[2]
[3]
[1] 1050fs2194c
141
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12. Remove 5 E-ring [2], the gear [3], the pin [4] and
[7]
the bearing [5] and [6] from the ADU conveyance
roller /1 [1].
/1050e/1050eP
NOTE
[2]
• When reinstalling the bearing [6], be sure that
[6] the flange [7] turns outside.
[2]
[1]
[3]
[2]
[4]
[2]
142
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When setting the belt, the tension is automat-
ically adjusted by the spring [5]. Be sure to
tighten up the screw [1] after the belt has
been set.
14. Remove the pierce ring [1], the spacer [2], the
pulley [3] and the pin [4].
15. Remove 2 screws [5] and pull out the ADU
reverse roller [6].
[2]
[3]
[1]
[6]
[5]
[4] 1050fs2197c
143
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
/1050e/1050eP
NOTE
• When reinstalling the bearing [3], be sure that
the flange [4] turns outside.
[2]
[1]
[2]
1050fs2198c
144
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[4] and the pin [5].
20. Remove 2 screws [6] and pull out the paper exit
roller /2 assembly [7].
[1]
[2]
[3]
[4]
[6]
[7]
[5] 1050fs2200c
145
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
21. Following the steps 18, 19 and 20, pull out the
paper exit roller /1 [1].
/1050e/1050eP
[1] 1050fs2202c
22. Remove 2 E-rings [2] and the bearing [3] from the
[4]
paper exit roller /1 [1].
[3]
NOTE
• When reinstalling the bearing [3], be sure that
[2] the flange [4] turns outside.
[1]
[2] 1050fs2203c
146
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Loosen 3 screws [1] and remove the reverse sec-
tion cover [2].
[1]
[2]
1050fs2204c
NOTE
• Reinstall the reverse/exit solenoid assembly
so that it comes to the same graduation [7] as
that used for removal.
147
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[6] [5]
[4]
[3]
[2]
[1]
1050fs2206c
[1]
1050fs2207c
148
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Open the front doors /Rt and /Lt, and pull out the
[1]
ADU from the main body. (See P.112)
2. Loosen 3 screws [1] and remove the reverse sec-
tion cover [2].
[2] 1050fs2786c
149
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When attaching the stepped screw [2], make
sure that it gets in securely up to the step of
the screw.
[3]
NOTE
• Reinstall the reverse/exit solenoid assembly
so that it comes to the same graduation [7] as
that used for removal.
150
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[1] 1050fs2792c
10. Remove the E-ring [1] and 2 screws [2], and slide
[2] [3]
the bearing [3] in the arrow-marked direction.
[1] 1050fs2788c
11. Pull out and remove gently the shaft [1] of the
fusing exit roller so that it does not touch the
guide plate.
[1]
1050fs2789c
151
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[4]
152
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
Caution:
• Immediately after turning off the main power switch (SW1) or the power switch (SW2), the fusing
section is very hot and you may get burnt. Be sure to start operations when the temperature cools
down sufficiently.
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2] 2. Remove 2 screws [1] and then remove the web
cover [2].
[1]
1050fs2163c
[2]
[1]
1050fs2164c
153
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[6]
NOTE
• Be sure to set each detent [5] on the driven
couplings to the notch [6] of the shaft on the
[5]
unused side. When the web is installed in the
wrong direction, it does not coincide with the
notch.
[1] NOTE
• The performance of the new cleaning web is
guaranteed from the position in which the
blue line disappears. Be sure to take up the
cleaning web up to this position.
[8]
[9]
[4]
[6]
[2] [5]
1050fs2165c
154
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• Be sure to set each detent [5] on the driven
coupling to the notch [6] of the shaft on the
unused side.
155
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• Immediately after turning off the main power switch (SW1) or the power switch (SW2), the fusing
section is very hot and you may get burnt. Be sure to start operations when the temperature cools
down sufficiently.
(1) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Open the paper reverse/exit section [1].
[3] 3. Open the fusing paper exit section [2].
[1] 4. Remove 2 screws [3] and then remove the fusing
cover [4].
[4]
[2] 1050fs2002c
156
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
the fusing section [4].
NOTE
• When fixing the fusing section [4], be sure to
tighten up the screw [3] while pressing it
toward the rear side.
[2] [4] [7] [1] 7. Close the fusing paper exit section [5].
8. Slide the fusing section [4] diagonally to the front
side and hold it up with both hand to remove it.
NOTE
[5]
• When holding up the fusing section, be sure
to hold it at the jam release knob [6] and the
handle [7].
• When reinstalling it, be sure to slide it with the
fusing section set to the reversal section side.
[6]
[3] 1050fs2003c
157
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When the web is closed and fixed, be sure to
rotate the shaft to apply pressure.
• Opening the web section disrupts the stabil-
[5] [6] ity. Be careful it does not fall down.
[6] 1050fs2167c
158 1
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• Be sure to avoid touching the lamp section of the fusing heater lamps /1 and /2 with bare hands.
When touched, be sure to clean it with the roller cleaner.
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[3]
2. Remove the fusing section. (See P.156)
3. Open the web section [1]. (See P.158)
[2]
4. Remove 2 screws [1] and then remove the 2 wir-
[1]
ing harness clamps [2].
5. Remove 2 faston terminals [4] of the fusing
heater lamp /1 [3].
[4]
NOTE
• Be sure to fit in the fusing heater lamps /1 and
/2 with the manufacturer's mark in this side.
• When reinstalling the fusing heater lamp /1,
be sure to insert it securely while taking note
of the position in which the faston terminal is
installed.
NOTE
[3] • When reinstalling the wiring harness clamp,
be sure to install it in the correct position.
[5] When it is installed in a wrong position, the
fusing cover cannot be attached.
[6]
[4] 1050fs2168c
159
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the fusing heater lamp /2,
be sure to insert it securely while taking note
of the position in which the faston terminal is
installed.
NOTE
[2] [6] • When reinstalling each of the fusing heater
lamps, check to see if either end of each lamp
is set in the fitting holes of the lamp fixing
plates /Fr [4] and /Rr [6].
• After each of the fusing heater lamps is
[5] installed, check to see if it is in touch with the
inner face of the fusing roller /Up [7].
160
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Heat insulating sleeve: Every 1,500,000 prints
• Bearing: Every 1,500,000 prints
• Fusing gear: Every 6,000,000 prints
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
2. Remove the fusing section. (See P.156)
3. Open the web section [1]. (See P.158)
4. Remove the fusing heater lamps /1 and /2.
(See P.159)
5. Remove the fusing roller /Up [1].
[1] 1050fs2169c
NOTE
• When reinstalling the heat insulating sleeve
and the bearing, make sure that the flange [7]
turns outside.
NOTE
• When reinstalling the heat insulating sleeve
and the bearing, make sure that the flange
[11] turns outside.
[8]
1050fs2170c
161
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
2. Remove the fusing section. (See P.156)
[3]
NOTE
• When removing the fusing roller /Lw assem-
bly with the web section open, the web sec-
tion may become unstable. So, be sure to
remove the cleaning web in advance.
(See P.153)
1050fs2171c
NOTE
• Before the roller is pressured, fix the pressure
spring end [1] in front and rear at 2 to 4 mm
[3] from the pressure plate end [2].
When this operation is not made, insufficient
fusing may result when printing a thick paper.
Standard: [3] 2 mm to 4 mm
[3]
[1] [2]
1050fs2919c
162 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
2. Remove the fusing section. (See P.156)
3. Open the web section [1].(See P.158)
4. Remove the fusing heater lamps /1 and /2.
(See P.159)
5. Remove the fusing roller /Up.(See P.161)
6. Remove the fusing roller /Lw assembly.
(See P.162)
7. Remove 2 screws [1] and then remove the fusing
cleaning unit [2].
[2] [1]
[1] 1050fs2172c
163
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
164
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
2. Remove the fusing section. (See P.156)
3. Remove the spring [1] (long one) and [2] (short
[5]
one).
NOTE
[1]
• The springs [1] and [2] are different in size and
length. When installing them, take note of the
positions in which they are installed.
NOTE
• When reinstalling the thick paper conveyance
assist plate [6], be sure to install the springs
[1] and [2] and the ground terminal [4] and
then push the thick paper conveyance assist
[5] [6] plate in the direction of the paper exit. The
plate must move smoothly.
165
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
[1] • When reinstalling the fixing plate, be sure to
set the positioning hole [3] and the position-
ing slot [4] to 2 projections [5] of the fusing
section.
[1]
166
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[2]
[3]
[1]
[1]
1050fs2175c
167
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling the fusing heating roller
assembly [1], be sure to set the guide hole [3]
/1050e/1050eP
[2]
[3] 1050fs2176c
168
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• Be careful not to touch the lamp section of the fusing heater lamp /3 with bare hands. When
touched, be sure to clean it with the roller cleaner.
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Remove the fusing section. (See P.156)
[1] 3. Open the fusing heating roller assembly.
(See P.165)
[2] 4. Cut off the wire binding band [1] and remove the
connector [2].
5. Cut off the wire binding band [3].
[8] NOTE
• When attaching a new wiring band, be sure to
[7] [9] use a heat-resistant one.
[10]
6. Remove the screw [4] and then remove the wir-
ing harness clamp [5].
[16] 7. Remove the faston terminal [6].
NOTE
• Be sure to fit in the fusing heater lamp /3 with
the manufacturer's mark in this side.
[15] • When reinstalling the faston terminal, be sure
to insert it securely.
[17]
NOTE
[5] • When reinstalling the fixing plate /Rr, be sure
to set the positioning hole [9] to the projection
[4] [10] of the fusing heating roller assembly.
NOTE
• When reinstalling the fixing plate /Fr, be sure
to set the positioning hole [13] to the projec-
tion [14] of the fusing heating roller assembly.
169
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
10. Pull out the fusing heater lamp /3 [1] from the
front side [3] of the fusing heating roller assembly
[2] and remove it.
/1050e/1050eP
[2]
NOTE
• When reinstalling the fusing heater lamp /3,
be sure to take note of the direction.
• After completion of the installation of the fus-
ing heater lamp /3, check to see if it is in
[1]
touch with the inner face of the fusing heating
[3] roller.
1050fs2801c
11. Reinstall the above parts following the removal
steps in reverse.
170
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• Heat insulating sleeve /Lw: Every 3,000,000 prints
• Bearing: Every 3,000,000 prints
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[5] [2] [4]
2. Remove the fusing section. (See P.156)
3. Open the fusing heating roller assembly.
(See P.165)
4. Remove the fusing heater lamp /3. (See P.169)
5. Remove the fusing cleaning sheet assembly.
(See P.163)
6. Remove the C-rings [1], one each, and then
remove the bearings [2], one each, to remove the
fusing heating roller [3].
NOTE
• When reinstalling the bearing, be sure to take
note of the direction of the flange [4].
[3] [1]
NOTE
• When reinstalling the heat insulating sleeves /
Lw, make sure that each of the flanges turn to
the fusing heating roller side.
171
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Remove the fusing section. (See P.156)
3. Open the fusing paper exit section
.(See P.158)
4. Remove the screw [1] and then remove 2 fusing
claw /Lw assemblies [2].
NOTE
• When reinstalling the fusing claw /Lw assem-
bly, be sure to set the positioning hole [3] to
the projection [4] of the fusing paper exit sec-
tion.
[3]
[4]
NOTE
• When reinstalling the fusing claw /Lw, be sure
to take note of the position [4] to which the
spring is hooked.
[4] 1050fs2180c
172
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
NOTE
1050e/1050eP
• The procedure for replacing the fixing claw/Up differs depending on whether the separation claw
shaking mechanism exist or not.
[2]
[1]
1050fs2181c
2 173
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[1]
1050fs2920c
174 2
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
2. Remove the fusing section. (See P.156)
3. Open the fusing paper exit section.(See P.158)
4. Remove the fusing sensor cover [1].
[1] 1050fs2182c
175
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[7] NOTE
[8] • When reinstalling the fusing sensor cover
plate, be sure to set the positioning hole [3] to
[5] the projection [4] of the fusing paper exit sec-
tion.
[3][4] 1050fs2183c
176
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When reinstalling the fusing actuator, be sure
to take note of the position [5] to which the
spring is hooked.
• When reinstalling the shaft fixing member, be
sure to take note of its direction.
[1] [5] [3]
177
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• After completion of the installation of the thermistor /2, be sure to check to see if it is in touch with
the fusing roller /Up.
(2) Procedure
1. Open the front doors /Rt and /Lt, and pull out the
ADU from the main body.(See P.112)
2. Remove the fusing section. (See P.156)
3. Open the fusing paper exit section [1].
4. Insert the driver [4] into the hole [3] of the shaft [2]
and rotate the shaft [2] clockwise to release pres-
sure.
NOTE
• Not releasing pressure may cause damage to
the fusing heater lamp. Be sure to release it.
• When reinstalling it, be sure to rotate the shaft
[1] [2] [3]
[2] counterclockwise to apply pressure.
NOTE
• When attaching the stepped screw [7], make
sure that it gets in securely up to the step of
the screw.
• Be sure to remove the web section with it
closed. If the web is removed with it open, the
web section becomes unstable and you may
get injured.
[2] 1050fs2185c
178
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
• When attaching a new wiring band, be sure to
use a heat-resistant one.
NOTE
• When reinstalling the thermistor /2 assembly,
[3] [2] check surely to see if it is in touch with the
fusing roller /Up [4].
NOTE
• There are 4 connectors for the thermistor pro-
vided at the same place and it is difficult to
identify a corresponding connector in
advance. Therefore, the connector to be
[5]
removed can be identified by following the
wiring harness of the thermistor /2.
[1] 1050fs2186c
10. Remove the screw [1] and then remove the ther-
[1]
mistor /2 [2].
11. Reinstall the above parts following the removal
steps in reverse.
[2] 1050fs2409c
179
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• After completion of the installation of the thermistor /4, check to ensure it is in touch with the fus-
ing heating roller.
(2) Procedure
1. Pull out the ADU from the main body.(See P.112)
2. Remove the fusing section. (See P.156)
3. Open the fusing heating roller assembly.
(See P.165)
4. Cut off 2 wiring bands [1].
5. Remove the screw [2] and then remove the wir-
[8] [5] [9] ing harness clamp [3].
6. Remove the screw [4] and then remove the ther-
mistor /4 assembly [5].
NOTE
• When reinstalling the thermistor /4 assembly,
be sure to set the attaching hole [6] to the
projection [7] of the fusing heating roller
assembly.
• When reinstalling the thermistor /4 assembly,
check to see if it is in touch with the fusing
heating roller [8].
NOTE
• There are 4 connectors for the thermistor pro-
vided at the same place and it is difficult to
identify a corresponding connector in
advance. Therefore, the connector to be
removed can be identified by following the
wiring harness of the thermistor /4.
180
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
[2]
• When attaching the wiring band, be sure to
use a heat-resistant one.
[3]
[1] 1050fs2410c
181
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(2) Procedure
1. Pull out the ADU from the main body. (See P.112)
[2] [1] [3]
2. Remove the fusing section. (See P.156)
3. Remove the screw [1] and then remove the wir-
ing harness clamp [2].
4. Remove the connector [3].
5. Remove 3 screws [4] and then remove the web
motor unit [5] in the arrow-marked direction.
[4] [5]
1050fs2188c
182
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
NOTE
• When reinstalling the web motor, be sure to
align the D-cut face of the web motor shaft
with the direction of the screw [2].
[3]
[2] 1050fs2411c
183
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to make the position adjustments when the roller has cooled down.
• When reinstalling the thermistor /1, adjust it with the temperature sensor positioning jig /A before
fixing it. Be sure to apply Screw-lock to the screw that has been fixed.
• After completion of the reinstallation of the thermistor /1, be sure to check the wiring harness to
see if it is in touch with the fusing roller /Up.
NOTE
[2] • When attaching a wiring band, be sure to use
a heat-resistant one.
NOTE
• For the method for installing the thermistor /
1, see "(2) Procedure for reinstallation."
NOTE
• There are 4 connectors for the thermistor pro-
vided at the same place and it is difficult to
identify a corresponding connector in
advance. Therefore, the connector to be
[4]
removed can be identified by following the
wiring harness of the thermistor /1.
[1]
1050fs2208c
184
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
[3] roller /Up [2].
2. Adjust the position of the thermistor /1 so that it
become flush with the temperature sensor posi-
tioning jig /A, and then fix it with the screw [4].
NOTE
• Be sure to adjust the distance a [5] between
the thermistor /1 and the fusing roller /Up so
that it becomes equal to the thickness of the
[1] temperature sensor positioning jig /A.
[4] Specified value: a = 0.75 ± 0.1 mm
• Make sure that the thermistor /1 is parallel to
the roller.
[2] 1050fs2209c
185
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to make the position adjustments when the roller has cooled down.
• When reinstalling the thermistor /3, adjust it with the temperature sensor positioning jig /A before
fixing it. Be sure to apply Screw-lock to the screw that has been fixed.
• After completion of the reinstallation of the thermistor /3, be sure to check the wiring harness to
see if it is in touch with the fusing heating roller.
NOTE
[1] • When attaching a wire binding band, be sure
to use a heat-resistant one.
[2]
5. Remove the screw [2] and then remove the 2 wir-
ing harness clamp [3].
6. Remove 2 screws [4] and then remove the ther-
mistor /3 [5].
NOTE
• For the method for installing the thermistor /
3, see "(2) Procedure for reinstallation."
[4]
NOTE
• There are 4 connectors for the thermistor pro-
vided at the same place and it is difficult to
identify a corresponding connector in
[5] advance. Therefore, the connector to be
removed can be identified by following the
wiring harness of the thermistor /3.
1050fs2210c
186
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
heating roller [2].
2. Adjust the position of the thermistor /3 so that it
become flush with the temperature sensor posi-
tioning jig /B, and then fix it with 2 screws [4].
NOTE
• Be sure to adjust the distance a [5] between
the thermistor /3 and the fusing heating roller
so that it becomes equal to the thickness of
[4] the temperature sensor positioning jig /A.
[1]
Specified value: a = 0.7 ± 0.1 mm
• Make sure that the thermistor /3 is parallel to
[3] the roller.
[2] 1050fs2211c
187
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to make the position adjustments when the roller has cooled down.
• When reinstalling the thermostat /1, adjust it with the thermostat positioning jig /A before fixing it.
Be sure to apply Screw-lock to the screw that has been fixed.
• After completion of the reinstallation of the thermostat /1, be sure to check the wiring harness to
see if it is in touch with the fusing roller /Up.
[3]
1050fs2212c
188
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
2. Insert the thermostat positioning jig /A [4]
between the thermostat /1 [1] and the fusing
roller /Up [3].
3. Adjust the position of the thermostat /1 so that it
become flush with the thermostat positioning jig /
A, and then fix it with the screw [5].
NOTE
[2]
• Be sure to adjust the distance a [6] between
the thermostat /1 and the fusing roller /Up so
[5]
that it becomes equal to the thickness of the
thermostat positioning jig /A.
[4]
Specified value: a = 3.0 ± 0.2 mm
[6]
1050fs2213c
189
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• Be sure to make the position adjustments when the roller has cooled down.
• When reinstalling the thermostat /2, adjust it with the thermostat positioning jig /B before fixing it.
Be sure to apply Screw-lock to the screw that has been fixed.
• After completion of the reinstallation of the thermostat /2, be sure to check the wiring harness to
see if it is in touch with the fusing heating roller.
NOTE
[2] • For method for reinstalling the thermostat /2,
see "(2) Procedure for reinstallation."
1050fs2214c
190
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
2. Insert the thermostat positioning jig /B [4]
[1] between the thermostat /2 [1] and the fusing
heating roller [3].
3. Adjust the position of the thermostat /2 so that it
become flush with the thermostat positioning jig /
B, and then fix it with the screw [5].
[5]
NOTE
• Be sure to adjust the distance a [6] between
the thermostat /2 and the fusing heating roller
so that it becomes equal to the thickness of
the thermostat positioning jig /B.
Specified value: a = 3.0 ± 0.2 mm
[3]
[4]
[6]
1050fs2215c
191
3. PERIODIC CHECK Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[2] NOTE
• When reinstalling the paper exit section, be
sure to hook the retention hole [4] to the pro-
jection [5] of the frame and then set the posi-
[4][5] [3] [6][7] tioning hole [6] to the positioning pin [7] of the
1050fs2216c
frame.
(2) Procedure
1. Remove the left cover. (See P.250)
2. Remove the paper exit section.(See P.192)
3. Clean the paper exit sensor (PS3) [1] with the
blower brush.
4. Reinstall the above parts following the removal
steps in reverse.
[1]
1050fs2217c
192
Field Service Ver3.0 Nov.2006 3. PERIODIC CHECK
1050e/1050eP
(2) Procedure
1. Remove the left cover. (See P.250)
[7] 2. Remove the paper exit section.(See P.192)
3. Remove the E-ring [1] and then remove the gear
[6] [2] and the pin [3].
4. Remove the E-ring [4] and then remove the bear-
[8] ing [5].
5. Remove the E-ring [6] and then remove the bear-
ing [7].
6. Move the main body paper exit roller [8] in the
arrow-marked directions [9] and [10] in this order,
[10]
and remove it.
7. Reinstall the above parts following the removal
steps in reverse.
[9] [5]
[1]
[4]
[2] [3] 1050fs2218c
193
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
4. SERVICE
4.1 Service material list
/1050e/1050eP
194 1
Field Service Ver3.0 Nov.2006 4. SERVICE
1050e/1050eP
55VAJG011 Temperature sensor 1
positioning jig /A (for
fusing roller /Up)
00VE-1005 Tester 1
2 195
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
196 2
Field Service Ver3.0 Nov.2006 4. SERVICE
1050e/1050eP
Parts name Useful life Type name
Toner bottle 80,000 prints TN010
Drum 1,000,000 prints or 220 hours DR010
Developer 1,000,000 prints or 220 hours DV010
197
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
"Mail remote notification system" is a system that allows you to obtain a list print which can be output by a
copier using the Internet mail (E-mail).
Using this system dispenses not only with printing the list on paper but also visiting the users.
Sending a mail filled-in with a simple keyword to the copier allows you to receive by mail all sorts of print infor-
mation of the copier.
(1) The copier has a server that can receive a mail using POP3 or IMAP protocol.
(2) The copier has a mail server that can send a mail using SMTP protocol.
(3) In the following 4 cases, "Mail remote notification system" does not operate in the copier.
When the main power switch (SW1) is turned off.
When the power switch (SW2) is turned off.
While the copier is in auto shut-off.
When the security enhanced mode is set to ON (the use of the main body NIC is not allowed.)
In this manual, the network interface card installed in the main body is called the main body NIC.
(1) The list print information of the copier you want to obtain can be received by mail.
List prints that can be obtained are the following 11 lists.
Mode memory list
User setting list
Font pattern list
Management list
Adjustment list
Parameter list
Use management list
Counter list
Pixel ratio list
Remote diagnostic report
Audit log report
198 1
Field Service Ver3.0 Nov.2006 4. SERVICE
1050e/1050eP
A. Setting from the touch panel
Set the IP address of the copier from the touch panel to connect the copier to the network. When already set,
proceed to "(2) Setting from the Web browser".
(1) Procedure
NOTE
• The IP address of the copier is normally assigned by the system administrator. For particulars,
contact the system administrator.
NOTE
• No space is available in all items to be set. The following characters cannot be used for setting an
E-mail address.
()<>;:“[]
When an improper entry or setting is made on the Web browser, be sure to make corrections fol-
lowing the error massage. When no correction is made, a down load error of the program may
result.
• The Web layout is subject to change without notice.
199
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
200
Field Service Ver3.0 Nov.2006 4. SERVICE
1050e/1050eP
Set item Details
Enable E-mail When using the mail remote notification system, select "Use." Default is "Not
notification use."
Time difference The time at which a mail was send out is calculated based on this value. For
time difference setting, enter the difference from the standard time UTC in the
range from -1200 (- 12 hour 00 minute) to +1200 (-12 hour 00 minute). When
no value is entered, +0000 (UTC) is set. (Ex.: In the case of Japan, enter +
900.)
Sending mail Set the IP address of the SMTP server.
(SMTP) server
SMTP port Set the port No. of the SMTP server. For default, 25 is set.
number
Sending mail For SMTP default, 5-minute is set.
(SMTP) server
time out
Interval between The copier check the receiving mail server to see if a mail is newly received.
fetching mails (An interval can be specified in the range from 1 minute to 60 minutes.) Taking
into consideration the load on the network, this is usually set at the interval of
10 minutes.
Receiving mail Set the IP address of the incoming mail server.
server
Kind of mail Select either of POP3 and IMAP. For default, [POP3] is selected.
spool
Pop3 (IMAP) When 110 is used for POP3 and 143 is used for IMAP, select "Use the default
port number value." When any value other than the default, select "Setting" and enter a
port number to be used in the text box.
2 201
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
User name on Enter an account name assigned to the copier by the incoming mail server.
the server
Password Enter a password to the account name above.
E-mail address Enter the mail address of the copier its own. This is normally "mail account
of this copy name@incoming mail server name."
machine
Nickname Enter a nickname that is added to the title (subject) of a mail sent from the
copier. No entry cause no problem.
CE password Enter a password that is added to the title (subject) of a mail sent to the
copier. The copier uses this password for security purpose.
Also Notice to • Not transfer: Default
the Administra- • Transfer an unright mail: When a mail received by the copier is not con-
tor form to the above password, or when the mail size is exceeding the spec-
ified size (10k bytes), a selection is made if the mail is communicated.
• Transfer all transmission mails: Transfer all mails that use "Mail remote
notification system."
Administrator When "Transfer an unright mail" or "Transfer all transmission mails" is
E-mail address selected, enter an E-mail address for transfer.
Announce delay A selection is made if the difference (time required) between the time when a
time in replay mail was sent to the copier and the time when the copier handled the mail is
mail indicated in the mail. For default, "Not indicate" is selected.
Enable POP After authentication is made by the mail receiving server, a selection is made
(IMAP) before to decide whether to send out the mail or not. For default, "Send" is selected.
SMTP
Sending test A mail sending test is made on the SMTP server. A test mail is sent to "E-mail
address for the copier" set in Step 2.
Receiving A receiving test is made on the incoming mail server. A test mail is received from
test "E-mail address of the copier" set in Step 2.
202
Field Service Ver3.0 Nov.2006 4. SERVICE
1050e/1050eP
input
GETLOG [List option name] Send back by mail the list print information specified G
in [List print name].
ModeMemory Send back [Mode memory list] by mail. M
UserSetting end back by [User setting list] mail. U
FontPattern Send back [Font pattern list] by mail. F
Management Send back [Management list] by mail. Ma
Adjustment Sent back [Adjustment list] by mail. A
Parameter Send back [Parameter list] by mail. P
UserManagement Send back [User management list] by mail. UseM
Counter Send back [Counter list] by mail. C
PixelRatio Send back [Pixel ratio list] by mail. Pi
CommunicationLog CommunicationLog Send back [Communication log Co
list] by mail.
AuditLog Send back [Audit log report] by mail. Au
ALL Send back all of the above list prints in mail. AL
Not specified [Counter list] is edited so that it can be shown by cell
phone. And this is sent back by mail.
CHPASS [OldPasswd][New- Change a password to be used for certification of a C
Passwd] mail.
[OldPasswd] Specify a password that is currently used.
[NewPasswd] Specify a new password.
HELP Not specified Send a help mail that describes the operating H
instructions of the commands above.
203
4. SERVICE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
A. Notes
• When sending a mail to the copier, take note of the following.
(1)Mail software can be used without discrimination by OS and a hand-held device or a free mail
using browser.
(2)Use the mail software in the text mode.
(3)For the mail software, as a condition for reception, 128 characters or more are recommended as
the maximum number of characters displayed in a line.
(4)There are one or more spaces or TAB's required between a command and an option that are
written in the mail. (However, a line feed is not allowed.)
(5)Enter all the commands that are written in the mail in alphanumeric characters (ASCII charac-
ters). When any other characters are used, an error message "No command found" is sent
back.
(6)Start a command written in the mail from the line head with not space.
When there is a space or TAB found at the line head, the line is ignored.
(7)The maximum number of commands available in a mail is ten. Commands exceeding ten are
ignored.
(8)Avoid attaching a file to a mail that is sent to the copier.
(9)A signature on a mail that is sent to the copier may be handled as a command with an error
message sent back.
(10)When the power is shut off while the copier is sending a mail or when the copier main body is
printing the list print, the same mail may be sent back twice.
(11)The copier can receive up to 5 mails from the mail server at the same time.
When more than 5 mails have been received by the mail server, the copier receives the
remaining mails from the mail server next time.
204
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
5.1.1 Outline
A. ISW (In-System Writer)
• This is an operation in which a control program stored in the flush ROM that is built in each control board in
the copier is rewritten with the board built in the copier main body. Conducting the ISW allows the version up
of control program without changing the board and the installation of the up to date program when replacing
the board. As a tool to conduct the ISW, (ISWTrns (PC software)) can be used for rewriting with the personal
computer (PC) connected to the copier. This tool can rewrite directly a control program in the flush ROM built
in the copier main body.
B. ISWTrns
• This is a software for Windows to rewrite the copier flush ROM and is used for the rewrite of programs (data
transfer) with the copier main body and the personal computer connected with a parallel cable or the USB
cable.
NOTE
• When this machine uses the USB to conduct the ISW, it is necessary to install the USB driver of the
ISWTrns. For procedure for installation, see "5.1.4 A. Installation of the USB driver (Windows2000/
XP)" When using the USB, be sure to turn on the radio button of the USB on the ISWTrns [Setting
(S)] - [Communications setting (C)], and then press the OK button.
205
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
5.1.2 Specifications
A. ISWTrns (PC software)
(1) ISWTrns disk composition
/1050e/1050eP
• Setup disk: 2
• Rewritable disk: Varies for each copier
Item Specifications
Board to be rewritten Overall control board, Printer control board, RADF control board, FD
control board, LS control board, IC control board, SD control board,
PB control board
Method for rewriting program 1. Local ISW from the PC
2. Web Utilities directional type ISW by using the Internet
3. Operation panel directional type ISW by using the Internet
Protocol FTP, HTTP
Network connection Use of the NIC of the copier main body
Rewritable program Image control I1 to I4 collectively, I1- I4
Printer control C1 to C2 collectively, C1, C2
DF F
FD, FS, LS, SD, PB H1, N1, S1-1/S1-2, B1, J1
Controller P1
Conditions Main body power turned on and program server provided
NOTE
• To execute the ISW, check surely to see if the power source of the main body has been turned on
in advance.
• For rewritable programs, it is not possible to rewrite plural programs at a time.
• When using the Internet ISW, it is required for it to be connected to the network environment by
using the main body NIC. As a network environment, programs must be down-loadable from the
program server on the Internet by using a ftp or http protocol.
206 2
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
(1) Procedure
207
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
USB driver is automatically started by the plug-and-play. However, this May result in the installation of the Win-
dows USB driver (USBPRINT.SYS) and be sure to set the USB driver following the steps given below.
(1) Procedure
Step Operation
1 From the screen below, select "Install from the list or the specified location," and then click [Next].
2 In the "Select the retrieve and install option screen," select "Select a driver for installation with no
retrieval," and then click [Next].
3 Select the UBS driver in the driver selection screen and click "Next" to start installation.
Driver name: Konica Minolta bizhub 1050/P USB Driver (ISW)
4 When the [Completed] in the "Hardware update wizard completed screen" is displayed, click
[Completed] to exit the installation.
5 Check the "Device manager screen" to see if the USB driver has been correctly installed.
Driver name: Konica Minolta bizhub 1050/P USB Driver (ISW)
208
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
ting of the PC parallel port. The ISWTrns does not correspond to the data transmission through the parallel port.
Accordingly, sending data in the ECP mode may result in an error while in transmission. Therefore, when using
the ISWTrns with the PC set in the ECP, it is necessary to release the ECP mode.
209
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Step Operation
1 Enter the service mode.
2 Press the [08 ROM version] key in "Service mode menu screen."
3 Press the [01 ROM version] key in the sub-menu displayed on the right side of the screen.
4 "ROM version screen"
Press the [08 ROM version] key and check the version information.
210
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
ferred file (rewritten data) is stored.
1) Procedure
5 "Option screen"
Click [OK] key. This operation stores the data folder created
in the step 4 into the INI file of the ISWTrns
program.
6 "ISWTrns screen"
The main screen of the ISWTrns program is displayed.
211
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
1) Procedure
212
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
selected by clicking [Copy] key into the data) that are displayed in the lower display section of
folder created at the setup of the the file from which a copy was made, click [Copy all] key
ISWTrns. instead of [Copy] key.
2. In the upper display section of the file into which a
copy has been made, a folder name created at the
setup of the ISWTrns is displayed.
3. In the list shown in the lower display section of the file
into which a copy has been made, files the copy of
which has been successfully completed are listed in full
path. In the copy error file list, files the copy of which
have been failed are listed. As the causes of failure, fol-
lowing are considered.
A. There exists a file of the same name and "O/W" is not
checked.
B. A folder into which a file is stored is not found.
C. An overwrite is made on an overwrite-prohibited file.
4. When changing a transferred file (rewritten data) that
is currently stored into a new data, click the overwrite
check box to make a check mark.
9 After completion of copy, click [Refresh]
key.
10 Click [Return] to get back to "option
screen."
11 "Option screen"
Click [OK] key.
213
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
D. Firmware
(1) Firmware data flow
The following shows the flow of the ISW data.
/1050e/1050eP
When conducting the ISW in the entire system, be sure to conduct it in the order shown below.
*1 Be sure to conduct the low end first out of those set in the sequence 1.
Ex.) When the composition is made up of "LS-501 (1st set) + LS-501 (2nd set) + FS-503"
FS-503 (N1) → LS-501 (S1-2) → LS-501 (S1-1)
*2 When the LS is the coupling of 2 sets, the 1st set (main body side) is S1-1 and the 2nd set is S1-2.
NOTE
• When the overall control board is replaced, be sure to conduct first of all the ISW of the image con-
trol program. When the image control program is not contained in the overall control board, other
programs cannot be written.
• Programs are not stored in the image processing board. So, when the board is replaced, the ISW
is not required.
NOTE
• When a finishing option is directly connected to the main body
Ex.1) Main body + FS
Connect the jumper connector to CN19 on the FNS control board (FNSCB)
Ex.2) Main body + SD
Connect the jumper connector to CN19 on the SD control board (SDCB)
Ex.3) Main body + PB
Connect the jumper connector to CN29 on the PB control board (PBCB)
Ex.4) Main body + LS
Connect three connectors of the LS to the main body and connect the 2 pin connector to the LS
214 2
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
Connect the connector on the FS side to CN19 on FNSCB
Ex.2) Main body + LS + SD
Connect three connectors of the LS to the main body and connect the 2 pin connector to the LS
Connect the connector on the SD side to CN19 on SDCB
Ex.3) Main body + FD + SD + FS
Connect the jumper connector to CN19 on the FDCB
Connect the connector on the SD side to CN19 on SDCB
Connect the connector on the FS side to CN19 on FNSCB
Ex.4) Main body + SD + PB
Connect the jumper connector to CN19 on the SDCB
Connect the connector on the PB side to CN29 on PBCB
2 215
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[When the main power switch (SW1) is required to be turned OFF/ON in the middle of the ISW]
When the system configuration is as shown below, the SW1 is required to be turned OFF/ON in the middle of
the ISW.
/1050e/1050eP
• Case 1: Main body + IC + DF-603 + LS-501 (1st set) + LS-501 (2nd set) + FS-503
ISW sequence: FS-503 → LS-501 (2nd set) → SW1 OFF/ON → LS-501 (1st set) → DF-603 → IC → Main
body
• Case 2: Main body + IC + DF-603 + LS-501 (1st set) + LS-501 (2nd set)
ISW sequence: LS-501 (1st set) → SW1 OFF/ON → LS-501 (2nd set) → DF-603 → IC → Main body
However, when the LS-501 (2nd set) is conducted first, the SW1 is not required to be turned OFF/ON.
1) When writing a new program (when replacing a board or when failed in writing a program)
When there is an abnormality found with the image processing program of the image processing board, or an
error is found with date displayed on the operation panel, a startup is normally unavailable. In the condition like
this, when the power switch is turned on, the system gets into the ISW standby status.
And when an abnormality occurs while in rewriting the image processing program and the contents of the mem-
ory is damaged, the power save LED is flashing when the power is turned on again, and the system gets into
the ISW standby status.
When the image processing program is in the normal condition and there is an abnormality found with other pro-
grams, an SC error is normally display on the touch panel while in the startup.
216
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
• PC into which transferred files (rewritten data) have been copied.
• Parallel cables
1) Procedure
Step Operations
1 Turn OFF the power of the copier.
2 Turn OFF the power of the PC.
3 Remove 5 screws and then remove the upper right cover.
5 Connect the parallel cables of the PC to the ISW connectors of the copier.
NOTE
• When exiting the ISW, be sure to clean each mirror of the scanner.
217
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
• UBS cables
1) Procedure
Step Operations
1 Turn OFF the power of the copier.
2 Turn OFF the power of the PC.
3 Remove 5 screws and then remove the upper right cover.
NOTE
• When exiting the ISW, be sure to clean each mirror of the scanner.
218
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
selection of transferred files (rewritten data), the display of information, the confirmation of a transferred file
(rewritten data) and the transmission of the transferred file (rewritten data) are conducted. For detailed informa-
tion of the functions, see the following.
[4]
[8] [5]
[6]
[7]
219
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
"OK": Accord
"NG": Not accord
"??": A corresponding checksum not found
/1050e/1050eP
Step Operations
1 Copy the data to the PC. (For the procedure, see "C. Firmware copy.")
2 Start the ISWTrns program.
3 Select the machine type, the destination and the board types.
• Machine type: bizhub 1050, Destination: KBJ, Board type: 11 to 14 collectively
4 The data to be used is displayed in the version file selection box and the transmitted file information
frame.
5 Press the [File Check] key to check if the data to be used has any problem.
220
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
7 Press the [Start] key on the copier main body side first, and then press the [File Send] key of the
ISWTrns.
8 The following window is displayed on the PC while in the data transfer.
[Copier side]
221
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
display it on the main body touch panel, but inform you of it by lighting or flashing the LED (with the ISW
placed in the standby condition). For the LED display, see the table given below.
222
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
2. When a file is copied into the folder in which a file of
the same name is contained with "Overwrite check box"
not checked.
3. When overwriting is made on an overwrite prohibited
file.
4. The file is used by another application. OS trouble.
The transferred file is not found, or a file with an The number of divisions of the transferred file written in
illegal name is found in the folder. Make sure of the checksum file does not correspond with the number
it. of files that actually exist.
1. When a file with an illegal name is in the data folder, or
a file name that seems to be illegal is displayed in the
folder list.
2. The number of divided files is insufficient. Check the
insufficient number of files in the folder list and copy
them again.
3. When the checksum file is damaged, copy it again to
the folder.
223
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When rewriting the IC firmware, the execution of the ISW is inhibited if the initialization of the IC is
not completed.
• When any one of the errors shown above occurs, an error code is not displayed, but the message
"Now initializing Controller" is shown in the touch panel section.
224 2
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
1 The ISWTrns does The ISWTrns file is damaged Set it up again.
not start up. The setup disk itself is damaged. Check the setup disk and set it up
again.
2 The screen is dis- The Japanese DLL[RCJP.DLL] is Set it up again.
played in English. damaged.
The INI file is set incorrectly. (The INI Check the ISWTrns.INI file.
file in English version is used.)
3 When an item in the The transferred file is not stored in Check to see if the relevant file is stored
combo box is the relevant folder. in the folder displayed in the "Folder"
selected, the trans- text box of "Select version." When a
ferred file is not dis- folder into which a file is stored is not
played. found, use the "File copy" function.
The data folder in the option screen Check the setting of the data folder.
is set incorrectly. When a folder into which a file is stored
is not found, use the "File copy" func-
tion.
The file name is illegal (or has been The file name must be used with no
changed.) change made. When the file name is
changed, the display or selection of the
file becomes unavailable. When the file
name is changed, return it to former
state.
The folder name is illegal (or has When the folder name created by the
been changed.) "Create folder" button in the option
screen has been changed, it cannot be
found. Return it to former state and
check it again.
4 "NG" is displayed The transferred file is damaged. Copy the file and check it again. When
while in the file check. "NG" still recurs, contact the supplier of
the file.
5 "??" is displayed When the transferred file was cop- Copy the checksum file to the same file
while in the file check. ied to the PC, the copying of the as the one for the transferred file at the
checksum file (*.SUM) was forgot- same time. (If you use the "Copy a file"
ten. function, a copy is made automatically.)
6 The transfer of the file
failed.
An error "The file can- The file is being used by anther pro- Exit another program. The error still
not be opened" is gram or system. recurs, reboot Windows.
displayed.
An error "Term Test The connection of the cable is loos- Check the cable to see if it is connected
file cannot be sent" is ened. securely or if there is any problem found
displayed. with the cable itself.
The main body is not in the receiv- Check the main body to see if it is in the
ing condition. receiving condition.
225
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
sion to the LPT port loosened. nected securely or if there is any prob-
failed" is displayed. lem found with the cable itself.
Wrong data has been sent. Check the file information screen to see
if the receiving mode on the copier side
(type of receiving board) corresponds
with the transferred file.
If the file is sent for the first time, con-
tact the file supplier.
The length of the cable is out Use a cable the length of which is less
of specifications. than 2 m.
The parallel port of the PC is See the PC manual to release the ECP
set to the ECP mode. mode.
There is a compatibility prob- Conduct a test with a PC with an actual
lem between the parallel port performance of transmission, and
of the PC and the port on the check to see if there is a compatibility
copier main body side. problem found.
226
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
"Internet ISW" is a system in which instructions are given to the ISW by using browser so that the copier auto-
matically obtain the program from the program server. Using the Web functions allows you to conduct the ISW
at the user's premise without taking the programs with you.
NOTE
• It operates while in the jam, SC and lower power mode.
1 227
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
5.2.4 Initialization
To make use of the Internet ISW, it is necessary to set in advance the network parameter, program server
address and the fire wall address of the copier.
/1050e/1050eP
(1) Procedure
NOTE
• The IP address of the copier is normally assigned by the system administrator. For particulars,
contact the system administrator.
228
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
NOTE
• No "space" is allowed in all set items.
• When an incorrect setting is made on the Web browser, be sure to correct it following the error
message. Correcting no input error may result in the download error of the program.
• The Web layout is subject to change without notice.
(1) Procedure
Step Operations
1 Start up the Web browser.
When the proxy is set on the Web browser, the main body Web may not be accessed.
For particulars, contact the network administrator. For Web browser, Internet Explorer or Netscape
Navigator is recommended. However, be sure to avoid setting from two or more browsers at a
time.
2 Specify the IP address of the copier main body that is entered thorough "A. Setting from the oper-
ation panel".
When you access the Web Utilities of the copier main body, "Main page" is displayed.
229
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Step Operations
5 Click [Internet ISW] in "Extension for maintenance."
/1050e/1050eP
230
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
When using no proxy server (fire wall), proceed to the step 9.
NOTE
• For types 2, 3 and 4, no guarantee is made.
• For authentication of proxy server, see "3.2.7 Authentication of
the proxy server in the Internet ISW."
Proxy Server IP When using the proxy server, set the IP address of the proxy server.
Address
Port Number When using the proxy server, set the number of the port that uses the proxy
server.
User name on When selecting the type 1 or type 2 in "Type of proxy server" above set the
the Proxy Server account of the proxy server.
Password for the When selecting the type 1 or type 2 in "Type of proxy server" above set the
Proxy Server password of the proxy server.
8 After completion of entry, click [Next] and then after checking the set items in the setting check
screen, click [Next]. However, if there is an input error, click [Back] following the message shown in
red and then re-set the item.
231
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Step Operations
9 Set the program server. (Proxy is used.)
/1050e/1050eP
Program server address Set the address of the server into which the program to be
down loaded is stored. Select the protocol to be used from
the pull-down menu left and enter the address after that in
the text box on the right. In the case of ftp, it is a relative path
from the home directory.
User name on the Program Enter the account name of the program server.
Server
Password for the Program Enter the password of the program server.
Server
Receiving time out Set the receiving time out of the program. When the time is
out, the down load of the program forcibly comes to an end,
and the system returns to the normal mode without conduct-
ing the ISW.
10 After completion of entry, click [Next]. Then after checking the set items in the setting check
screen, click [Completed]. However, if there is an input error, click [Back] following the message
shown in red and then re-set the item.
11 Set the program server. (Proxy is not used.)
232
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
screen, click [Complete]. However, if there is an input error, click [Back] following the message
shown in red and then re-set the item.
13 Conduct the Download test.
• In the down load test, "test.dat" is down loaded from the program server set in the initialization
to check the settings. When the down load test failed, re-check the set items following the error
message.
• When the down load test is successfully completed, the communication speed and the
expected down load time are displayed as shown below. Refer to the "Receiving time out" set-
ting.
• When the down load test failed, the response error code from the server is display as shown
below. Since there may be a setting error, re-check the initialization.
233
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
Step Operations
1 Proceed to "Internet ISW" on the Web Utilities.
The ROM version of the board is displayed beside each of the board names.
2 Select one of the ISW-intended boards in the item "ISW," and check its check box. When specify-
ing the file name to be down loaded, enter it in the "File name" text box column. When specifying
no file name, obtain the following from the specified program server address.
234
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
From the screen shown below, you can check the current processing condition to see if there is any
error.
• "ISW in communication"
• "ISW in rewriting"
• "Completed successfully": Be sure to avoid pressing the "Read again" key of the browser to
reboot after successful completion.
• "Aborted due to a communication error."
• "Aborted due to a communication time error."
• "Aborted due to a writing error."
5 When the ISW is completed successfully, the copier restarts automatically to complete the ISW.
NOTE
• Clicking the [Check progress] key allows you to abort the ISW only while in program-
ming.
6 After restart of the copier main body, check the ROM version in "Internet ISW main screen" to see if
it is being updated successfully.
(2) When the power supply is cut off while writing the image control program in the overall control
board (OACB).
When the main power switch (SW1) turns off due to a power failure, the copier does not start up.
If the main power switch is turned off due to the failure of power supply and Internet ISW is abnormally termi-
nated, be sure to go to the copier that has been conducting the Internet ISW and use the ISWTrns to reperform
the rewriting of the program.
235
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
Ex.: When the image control program is rewritten collectively.
Step Operations
1 Display "ISW rewrite screen."
236
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
key and enter the file name by hand for execution.
5 When ISW is completed normally, the copier is rebooted and exits ISW automatically.
6 After the copier main body is rebooted, check the [ROM version screen] to see if the ROM version
has been updated normally.
237
5. FIRMWARE VERSION UP Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
proxy of a client who receives an access demand (HTTP and FTP) from the client.
(3) Type 3: FW user name => FW password => SITE host name
This is a type that requires the authentication to the proxy server itself when accessing the outside.
The information of the server you want to access and the user name and password of the proxy server (F/W) are
required.
When accessing the outside through the proxy server and when the user name and the password of the proxy
server are required, this proxy authentication is likely to be used.
238
Field Service Ver3.0 Nov.2006 5. FIRMWARE VERSION UP
1050e/1050eP
PASS FW password 230 Transmit the password for the user name above
SITE Host name ftp expanded Transmit the user name of the program server
function, defined
for each server
USER User name 331 Transmit the user name of the program server
PASS Password 230 Transmit the password for the user name above
(4) Type 4: FW user name => FW password => USER user name@host name
This is almost the same as the type 3, except for the exchange of commands while in authentication.
When all the settings are made correctly and no communication is available with type 3 authentication, this set-
ting is used.
Command
D. Remarks
For fwtk2.1 (for Unix) and Black Jumbo Dog (for Windows), the type 1 authentication is used.
For most of the proxy servers, the type 1 authentication is used.
When the authentication type of the proxy server is not known, you are recommended to make settings in type
1 authentication as a temporary measure.
239
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
6. OTHERS
6.1 Items not allowed to be disassembled and adjusted
/1050e/1050eP
[2]
[1]
[1]
[3]
1050fs2073c
[1] Screws not allowed to be removed [3] Read position adjusting plate /Rr
[2] Read position adjusting plate /Fr
240
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[2]
[1]
1050fs2219c
241
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[2]
[1] Screws not allowed to be removed [4] Lens reference plate assembly
[2] Screws not allowed to be removed [5] Attaching screw of the CCD unit (allowed to
[3] CCD unit be removed when replacing the CCD unit)
242
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[1]
[2]
[1]
[1] 1050fs2220c
243
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[5] [1]
[4]
244
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
• 5 attaching screws of the transfer guide plate
• 2 attaching screws of the transfer assist home sensor assembly
[4] [1]
[3]
[2] 1050fs2222c
[1] Screws not allowed to be removed [3] Transfer assist home sensor assembly
[2] Screws not allowed to be removed [4] Transfer guide plate
245
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[2] 1050fs2223c
246
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[1]
[1] 1050fs2225c
247
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[3] [2]
1050fs2224c
[1] Screws not allowed to be removed [3] Write position adjusting shaft
[2] Write position adjusting shaft fixing plate
248
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
• This list shows the explanation of the disassembly and reassembly of the parts which are consid-
ered necessary to replace (other than periodically replaced parts). However, these parts except for
the covers are not required to be disassembled while in normal service operations.
• For the method of replacing the periodically replaced parts, see "3.5 Maintenance procedure".
249
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Caution:
/1050e/1050eP
• When disassembling/reassembling the parts, be sure to unplug the power cord of the main body
from the power outlet.
6.3.1 Cover
A. Removing/reinstalling the rear cover
(1) Procedure
1. Remove 9 screws [1] and then remove the rear
[2] [1]
cover [2].
2. Reinstall the above parts following the removal
steps in reverse.
[1]
[1] 1050fs2057c
[1]
[1]
1050fs2058c
250
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
cover [2].
2. Reinstall the above parts following the removal
steps in reverse.
[1]
[1]
[2]
1050fs2059c
[1]
1050fs2060c
251
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[3]
[2]
1050fs2061c
252
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[3] into the hole [2] provided in the lower sec-
tion of the front door /Lt.
[1]
[2] 1050fs2062c
253
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3] NOTE
• When reinstalling the toner supply door [1], be
sure to insert the projection [6] of the hinge
[2] [5] into the hole [4] provided in the lower sec-
tion of the toner supply door.
[1]
3. Reinstall the above parts following the removal
steps in reverse.
[6]
[4]
[5]
1050fs2063c
254
Field Service Ver3.0 Nov.2006 6. OTHERS
NOTE
1050e/1050eP
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
(1) Procedure
1. Remove 3 screws [1] and then remove the upper
cover /Rrl [2].
[2] 2. Reinstall the above parts following the removal
steps in reverse.
[1]
1050fs2064c
NOTE
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
(1) Procedure
1. Remove 2 screw caps [1].
[3]
2. Remove 2 screws [2] and then remove the upper
cover /Rr2 [3].
3. Reinstall the above parts following the removal
steps in reverse.
[2]
[1]
1050fs2065c
255
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
(1) Procedure
1. Remove 3 screw caps [1].
[3]
2. Remove 5 screws [2] and then remove the upper
[2] cover /Rt [3].
3. Reinstall the above parts following the removal
[2]
steps in reverse.
[1]
1050fs2066c
NOTE
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
• When reinstalling the original glass, be sure that the shading correction plate (white) is on the
upper side of the glass.
(1) Procedure
1. Remove the upper cover /Rt.
[3] [6]
(See P.256)
2. Remove 2 screws [1] and then remove the origi-
[4]
[5] nal stopper plate /Lt [2].
3. Remove 3 screws [3] and then remove the origi-
nal stopper plate /Rr [4].
[1] 4. Remove 2 screws [5] and then remove the origi-
[2] nal stopper plate /Rt [6].
5. Remove the original glass [7].
6. Reinstall the above parts following the removal
steps in reverse.
[7] 1050fs2067c
256
Field Service Ver3.0 Nov.2006 6. OTHERS
NOTE
1050e/1050eP
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
(1) Procedure
1. Remove 2 screws [1] and then remove the origi-
[1]
nal stopper plate /Lt [2].
2. Remove 2 screws [3] and then remove the upper
[4]
[2] cover /Lt [4].
3. Reinstall the above parts following the removal
steps in reverse.
[3]
1050fs2068c
NOTE
• The same removal and reinstallation procedure is applicable when the DF-603 is provided.
a. Procedure
1. Remove the upper cover /Rt.
[1]
(See P.256)
2. Remove the original glass.
(See P.256))
3. Remove the upper cover /Lt.
(See P.257)
4. Remove the original glass guide /Fr [1].
1050fs2069c
257
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(See P.257)
7. Remove 4 screws [2] provided on the bottom of
the upper cover /Fr [1].
[2]
[1]
[2]
[2]
1050fs2070c
258
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
steps in reverse.
1050fs2071c
259
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• After completion of reinstallation of the CCD unit, be sure to conduct the image adjustments in of
the service mode. (See P.317)
(1) Procedure
1. Remove the upper cover /Rt.
[1]
(See P.257)
2. Remove the original glass.
(See P.256)
3. Remove 10 screws [1] and then remove the lens
light blocking cover [2].
[1]
[2]
[1] 1050fs2075c
[1] 1050fs2076c
260
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
the direction as shown in the drawing to
release the lock and pullout the ribbon cable.
[1]
[2] 1050fs2078c
261
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
unit [4].
8. Reinstall the above parts following the removal
steps in reverse.
[3]
[1] [2]
1050fs2080c
1050fs2081c
262
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
clamp [4].
[8] 8. Remove the connector [5].
9. Remove the screws [6], one each, and then
remove the lamp presser plates /Fr [7] and /Rr
[8].
[6] 10. Remove 2 screws [9] and then remove the expo-
sure lamp [10].
11. Reinstall the above parts following the removal
[2]
steps in reverse.
[10]
[1]
[2]
[3]
[5]
[9]
[6]
[4] [7]
1050fs2082c
263
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(See P.256)
2. Remove the original glass.
[3] (See P.256)
3. Remove the upper cover /Lt.
(See P.257)
[8] 4. Remove the upper cover /Fr.
(See P.257)
5. Move the exposure unit [1] to the notch position
[7] [2] of the main body frame.
6. Remove 2 screws [3] and then remove the cord
[4] presser member [4].
7. Remove the screw [5] and then remove the
[2]
[1] ground terminal [6].
8. Remove the connector [7].
9. Remove 4 screws [8] and then remove the expo-
sure unit [1].
[2]
[8]
1050fs2083c
264
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
2. Insert the optics unit positioning jig [3] into the V-
mirror positioning hole [2] and fix the V-mirror unit
[1].
[3]
NOTE
• Be sure to insert the optics unit positioning jig
[3] from the front side and pass it through the
V-mirror unit [1].
[1] [7] [2]
• Be care full not to confuse the V-mirror posi-
tioning hole [2] with the unused hole [4].
[3]
1050fs2084c
265
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
(1) Procedure
[1] [2]
[4]
[3]
[3]
[3]
1050fs2226c
NOTE
• Be sure to insert the optics unit positioning jig [3] from the front side and pass it through the V-mir-
ror unit [1].
• Be care full not to confuse the V-mirror positioning hole [2] with the unused hole [4].
266
Field Service Ver3.0 Nov.2006 6. OTHERS
[5] [12]
[5]
[2] [13] [9]
[22]
[15] [13]
[14]
[17]
[22]
[4]
[20]
[15] [7]
[18]
[17]
[16]
[11]
1050fs2227c
8. Drop the metal ball [3] in between the scanner wire /Fr [1] and /Rr [2] into the installation hole of the drive
pulley [4]. And with this hole as a starting point, wind the wire 4 turns [5] outwards and 5 turns [6] inwards.
NOTE
• Be sure to wind the scanner wire with the metal ball [7] at the end outwards and the scanner wire
with the wire terminal [8] at the end inwards.
• For both scanner wires, be sure to pull out the one wound outwards in the paper feed direction [9]
from above the drive pulley and the one wound inwards in the paper exit direction [10] from above
the drive pulley.
9. For each scanner wire that has been wound round the drive pulley, fasten it to the respective wire stoppers
through the wire stopper /Fr [11] or /Rr [12] pulley /1 [13] and via the outside of the pulley [15] of the V-mir-
ror unit [14].
NOTE
• Each wire stopper is provided with 2 grooves. Fix the metal ball [7] in the groove on the outside for
the wire stopper /Fr [11], and fix it in the groove on the inside for the wire stopper /Rr [12].
267
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
10. For each scanner wire that has been wound round the drive pulley, after reversing it by the pulley /2 [16],
pass it through the inside of the pulley [15] of the V-mirror unit [14] and pulley /3 [17] and hook the wire ter-
minal [8] to the spring fixing plate [18].
/1050e/1050eP
NOTE
• Be sure to paste it so that the wire restriction
sheet comes in contact with the wire.
1050fs2421c
12. Fasten tentatively each of the spring fixing plates with the screw [20].
13. Loosen once the screw [20], attach the spring [21] between 2 spring fixing plate [18] and then fix each
spring fixing plate with the screw [20].
NOTE
• After attaching each of the scanner wires, check the respective exposure unit mounting brackets
[22] if they turn to the inside.
14. For the parts to be installed hereafter, reinstall them following the removal steps in reverse.
268
Field Service Ver3.0 Nov.2006 6. OTHERS
Cautions:
1050e/1050eP
• Be absolutely sure not to turn on the writing section with it displaced from its regular position.
• Be absolutely sure not to remove the writing section cover. If laser beams get in your eyes, you
may suffer loss of sight.
• After turning off the main power switch (SW1) or the power switch (SW2), be absolutely sure not to
remove the writing section for about 2 minutes.
[3] NOTE
• When reinstalling the writing section cover
[2], hold it by inserting the notch holes [3] at
either side into the hooks [4] of the main body
frame.
[1]
[2]
[1]
[1]
[3] [4]
1050fs2085c
269
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2] 1050fs2086c
270
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
NOTE
• The same procedure for removing/reinstalling the lift wire is used for both the trays /1 and /2.
(1) Procedure
1. Remove the tray.
(See P.94)
2. Remove 2 screws [1] and the 2 screws [2] with
washer.
[3] 3. Remove the connector [3] and then remove the
tray front cover [4].
[2]
[2]
1050fs2754c
271
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[4]
[8]
1050fs2755c
272
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[4] [1] [2]
[2]
[3]
1050fs2756c
10. Slide the pulley [1] and remove the wire end [2]
[2]
from the shaft hole [3].
NOTE
• When reinstalling it, lift up the paper lift plate
a little to give slack to the lift wire you want to
insert. Then insert the wire ends [2] into the
shaft hole [3] one at a time and fix it with the
pulley [1].
273
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12. Remove the lift wires /Fr1 [4] and /Fr2 [5] from
the pulley [3].
NOTE
• When reinstalling it, make sure that the lift
wires /Fr1 [4] and /Fr2 [5] are contained in the
wire cover [2] and they are not crossing each
other.
[4] [5]
1050fs2758c
13. Pull out from up to down the lift wires /Fr1 and /
[2] [1]
Fr2 [2] from the arm [1] of the paper lift plate.
NOTE
• Be sure to pull out the lift wire gently and take
care that the lift wire does not get damaged
by the edges of the metal frame.
1050fs2759c
274
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[4].
16. Remove 4 screws [5] and then remove the con-
nector mounting plate [6].
1050fs2760c
[4]
[1] 1050fs2761c
275
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
20. Remove the lift wires /Rr1 [4] and /Rr2 [5] from
the pulley [3].
NOTE
• When reinstalling it, make sure that the lift
wires /Rr1 [4] and /Rr2 [5] are contained in the
wire cover [2] and they are not crossing each
other.
21. Pull out from up to down the lift wires /Rr1 and /
[2] [1]
Rr2 [2] from the arm [1] of the paper lift plate.
NOTE
• Be sure to pull out the lift wire gently and take
care that the lift wire does not get damaged
by the edges of the metal frame.
NOTE
• The lift wire /Fr is grey in color and /Rr black
in color.
• Make sure that the lift wires do not cross
each other.
• After completion of installation, check the
paper lift plate to ensure it is level.
1050fs2763c
276
Field Service Ver3.0 Nov.2006 6. OTHERS
NOTE
1050e/1050eP
• The same removal and reinstallation procedures of the paper feed assist fans /Fr1 (FM20), /Rr1
(FM21) and /Fr2 (FM22), /Fr2 (FM23) are used for trays /1 and /2.
(1) Procedure
1. Remove the tray.
[2] [3] [1]
(See P.94)
2. Loosen a screw [1].
3. With the release lever [2] placed at its original
position, hold the stopper [3] and tighten the
screw [1] to fix the stopper.
4. Remove the tray front cover and lift wire.
(See P.271)
1050fs2422c
1 277
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
6. Hold down the paper stopper [3] and pull out the
lift plate cover [4] upward to remove it.
NOTE
• When removing the lift plate cover [4], raise
up the pick-up roller [5] in the arrow-marked
direction to move it out of the way.
• When reinstalling the bracket [2], push it
lightly in the opposite direction of removal
and fix it with screws.
[1]
[2]
1050fs2764c
278
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
and then fix the lift plate.
[1] [2]
1050fs2765c
NOTE
• To make it clear, the picture shows the condi-
tion in which the lift plate is removed.
1 279
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When reinstalling it, be sure to fasten the
paper guides /Fr [5] and /Rr [6] with the
screws [2] and the screws [3], 3 each. Then
tentatively tighten the screws [1] and the
screws [4], 3 each and tighten them up fully
after placing the paper guides /Fr and /Rr in a
[5] [6] horizontal position.
To check the verticality of the paper guides,
move the guide plate up and down with copy
paper placed on the lift plate and check the
clearance of the paper guide.
[4]
[2] 1050fs2768c
280 1
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[2]
1050fs2769c
[6]
[5]
[3]
[4] 1050fs2770c
281
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[1]
1050fs2771c
[3]
[4]
1050fs2772c
282
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
and a spring washer) [4] and 3 screws [5], and
then remove the fan motor mounting plate [6].
[6]
[3]
[5]
[4]
1050fs2773c
20. Cut off the connector [1] and the wire binding
band [2].
21. Remove 2 screws [3] and the paper feed assist
fans /Fr1 (FM20), /Fr2 (FM22) [4].
283
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
/1050e/1050eP
• The same removal and reinstallation procedures are employed for the paper lift motors /1 (M25)
and /2 (M26) of the trays /1 and /2.
(1) Procedure
1. Remove the tray.
(See P.94)
2. Remove 2 screws [1] and 2 screws [2] with
washer.
[3] 3. Remove the connector [3] and then remove the
tray front cover [4].
[2]
[2]
1050fs2775c
284
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[2] [3] 1050fs2776c
285
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[4] 8. Remove the bearing [5], the bearing [6] and the
torque restriction gear [7] together with the gear
[6]
[3] mounting plate [4].
[5]
[1] NOTE
• When removing the gear mounting plate [4],
[7]
take note that the gear comes off freely.
• When reinstalling it, make sure that the step
[8] of each shaft gets in the gear mounting
plate [4] securely.
[2] • Be sure to reinstall the bearing (large) [5] from
the outside of the gear cover [4] and the bear-
ing (small) [6] from the inside.
[4]
[8]
1050fs2777c
286
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[2] [1]
[2]
[3]
1050fs2778c
[1]
1050fs2779c
287
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• For ease of the removal and reinstallation
operations, press the release lever [4] so that
the coupling gear [5] can raise.
288
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
NOTE
• The multi feed detection boards /1 and /2 were adjusted as a unit during the production process.
Be sure to replace it as a unit when replacing one.
• When replacing the multi feed detection board /1 and /2, be sure to conduct the sensitivity adjust-
ments of the multi feed sensor. (See P.380)
(1) Procedure
1. Remove the registration section.
(See P.112)
2. Remove 2 screws [1] and the remove the multi
feed detection board /2 (MFDB2) [2].
[2] [1]
1050fs2228c
289
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
290
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
NOTE
• The ADU is very heavy. So when removing and/or reinstalling it, be sure to conduct the operation
with 2 people.
(1) Procedure
1. Pull out the ADU main body.
(See P.112)
2. Remove the fusing section.
[1] (See P.153)
3. Remove the transfer/separation section.
(See P.112)
4. Remove the registration section.
(See P.112)
5. Open the paper reverse/exit section [1].
6. Remove 2 screws [2] and then remove the con-
nector cover [3].
7. When reinstalling the connector cover, be sure to
set the positioning hole [4] to the projection [5] of
[4] [5]
the ADU.
[2] [3]
1050fs2142c
291
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[1] 1050fs2143c
[2]
[1]
1050fs2144c
292
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
tion [6] with 2 people and remove the ADU.
NOTE
• Be sure place the ADU in a horizontal place.
• Placing the ADU from the front side diagonally
may deform the open/close door /A [7]. Be
absolutely sure to avoid this.
[4] [1]
12. Reinstall the above parts following the removal
steps in reverse.
[7]
[2]
[5]
293
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
6.3.7 HDD
A. Removing/reinstalling the hard disk /1
(1) Procedure
/1050e/1050eP
[2]
[3]
294
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
(See P.250)
2. Remove 2 connectors [1].
3. Remove 4 screws [2] and then remove the hard
disk mounting bracket [3].
4. Remove 4 screws [4] and the remove the hard
disk /2 (HDD2) [5].
5. Reinstall the above parts following the removal
steps in reverse.
[1]
[3] [4]
[2]
[5]
[2]
[4]
1050fs2232c
295
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
A. Connecting connector
(1) Connector position
[1]
1050fs2233c
[1] CN160
296
Field Service Ver3.0 Nov.2006 6. OTHERS
Connector Pin No. Signal name Description Output timing Type of signal
1 PAT1 Light ON signal L signal output when the Open collector
1050e/1050eP
printing available
2 PAT2 L signal output while in the
scanning or printing operation
3 PAT3 L signal output when an
abnormal stop occurs due to
jams, error codes, no paper,
160
or no toner
4 PAT4 L signal output when the
toner supply message is dis-
played
5 24V 24V DC source At all times 24V,
500 mA
6 P.GND Power ground — —
297
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
[4] 1050fs2412c
[2] 1050fs2413c
298
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[2] 1050fs2423c
[2] 1050fs2414c
1050fs2415c
299
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
1050fs2416c
300
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[3].
10. Reinstall the arm cover /1, the arm cover /2 and
the adjusting knob following the removal steps in
reverse.
[3]
[4] 1050fs2417c
301
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• When wiring, be sure that the wiring harness
does not come in contact with the drive sec-
tion.
12. Reinstall the upper cover /Rt and the rear cover
following the removal steps in reverse.
1050fs2418c
302
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[1]
[4]
[3]
[2]
1050fs2234c
303
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
"PCS" stands for "proactive customization support," and three types of items are set so that the demands
expected in the POD market and Product printing market can be met. Providing these parts allows customiza-
tion adequate to the user's type of usage.
(2) Characteristics
8 types of the transfer assist sheets are provided according to the paper sizes. However, when changing to
sizes other than those provided as standard equipment, it is necessary to add a new relay wiring harness and
size detection connector.
It is possible to use a number of the transfer/separation assist sheets. On that occasion, however, after adding
the relay wiring harness mentioned above, it is necessary to purchase a transfer assist sheet that has been
incorporated into the transfer/separation charger unit. This transfer/separation charger unit must be provide with
a size detection connector.
NOTE
• When using plural sizes jointly, the transfer/separation unit of standard equipment (A3 and A4/
metric, 11 inches) requires the size detection connector.
• Since no individual counter is equipped, when the unit is replaced for each size, the management
of the counter is unavailable.
• Reference:
Double sided print job on the following condition
Transfer size: 8.5 inches
Weight: 91 g/m2 or less
No. of prints: 10
Size of the transfer assist sheet: A4S, A5
The copy count by parts that need to be replaced on this condition is as shown below. On this occasion, even if
the transfer assist sheet size is A4S or A5, the transfer size is "8.5 inches" and the count is up at 8.5 inches
No. 107 8.5 inches. double sided paper through count 10 counts
No. 108 A4S, A5 double sided paper through count 0 count
304
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
Transfer/separation Used exclusively for A3, A4 Brown Default size for metric area
charger unit Used exclusively for 11 inches Red Default size for inch area
Used exclusively for 8K, 16K Orange
Used exclusively for B4, B5 Yellow
Used exclusively for 8.5 inches Pink
Used exclusively for A4S, A5 Blue
Used exclusively for 8, 8.125, 8.25 inches Purple
Used exclusively for B5S Gray
Transfer assist Used exclusively for A3, A4 — Default size for metric area
sheet assembly Used exclusively for 11 inches Default size for inch area
Used exclusively for 8K, 16K
Used exclusively for B4, B5
Used exclusively for 8.5 inches
Used exclusively for A4S, A5
Used exclusively for 8, 8.125, 8.25 inches
Used exclusively for B5S
B. Cleaning brush
(1) Purpose
A cleaning brush is used while in the overlay printing in which coated paper is used. For coated paper while in off-set print-
ing, ink gets dry slowly. Therefore, to prevent the transfer of ink onto the backside of the paper, powder is normally sprinkled.
The cleaning brush is used to prevent the occurrence of a no feed condition due to this powder.
However, to maintain the specified performance, the cleaning brush needs to be cleaned every 2,000 sheets of
paper through while in overlay printing.
Do not use the cleaning brush for the paper with many paper powders. The cleaning brush may be clogged by
the paper powder and the conveyance power may be reduced.
(2) Characteristics
The cleaning brush can clean the pick-up roller and the paper feed roller.
Since it is used while in the overlay printing, it can be installed only in the tray 4 of PF-701 that is used while in
the overlay printing.
(2) Characteristics
The paper feed assist plate weighs about 10g and the pick-up roller can be equipped with up to 4 plates.
Increasing or decreasing the number of plates allows you to adjust the pick-up pressure corresponding to the
type of paper.
4 plates only are packaged together with the main body and they can be purchased as service parts when
required.
1 305
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
When changing from the standard size to any other size, it is necessary to purchase the following parts.
• PCS corresponding (other than the standard size) transfer /separation charger unit (assembled with the trans-
fer assist sheet) *
• Size detection connector
• Relay wiring harness
• Wire binding band
* Other than the transfer/separation charger unit assembled with each size of the transfer assist sheet, it is
possible to purchase the transfer assist sheet assembly.
1050fs2019c
306
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
[3]
307
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• Be sure to install the wiring harness of the
size detection connector [3] so that the rear
end section [5] does not protrude from the
inner end [7] of the connector bracket plate
[6] [1] [6]. If it is protruding, the wiring harness may
be broken.
• For the size detection connector, it is neces-
sary to install the one corresponding to the
size to be used. This can be identified by the
[5]
wire color of the size detection connector.
[7] (See P.306)
[4]
[2] [3]
1050fs2022c
[5]
[7]
[3]
[1] [2]
1050fs2023c
308
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
11. Pull around the relay wiring harness [1] as shown
in the drawing and hold it with the relay wiring
clamps [4] provided at the 12 placed.
[4] [1]
[3]
[1]
NOTE
• When the above software DIPSW is changed,
the size detection connector is required by
[4] [2] 1050fs2025c
the transfer/separation charger of standard
size. When the size detection connector is not
installed, the transfer assist sheet does not
operate.
309
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[2]
1050fs2722c
(2) Procedure
For the main body, see "11.1.3 Pick-up roller load adjustment".
For the PF, see"5.3 Adjusting the pick-up roller pressure" in the Field Service for the PF-701.
310
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
classification Cleaning Check Lubrication Replacement Tools used
1 Transfer/ (1) Removal of trans-
separation fer/separation unit
charger unit
(2) Replacing of trans- 1 z
fer assist sheet
assembly
* 1 For the PCS corresponding transfer assist assembly, the counter management is not available. The numer-
ical values given here are reference.
311
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
C. Maintenance procedure
Caution:
/1050e/1050eP
• When replacing the periodically replaced parts, be sure to unplug the power cord of the main body
from the power outlet.
2) Procedure
See “3.5.8 J. Replacing the transfer assist sheet assembly”.
312
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
"CMS" stands for "customer maintenance support," and this is applicable when the user wants to change parts
by himself.
For CMS corresponding parts, 9 types of parts are set. However, some parts provided as an assembly of parts
larger than those replaced normally by the CE so that the user can easily conduct the part replacement opera-
tion.
NOTE
• The steps 1 to 8 are applicable.
NOTE
• The steps 1 to 5 are applicable.
NOTE
• The steps 1 to 8 are applicable.
2 313
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NOTE
• The steps 9 to 11 are applicable.
NOTE
• The steps 1 to 2 are applicable.
NOTE
• The steps 9 to 11 are applicable.
314 2
Field Service Ver3.0 Nov.2006 6. OTHERS
1050e/1050eP
2) Replacement cycle
• Waste toner recycle box (RC-501) : 750,000 prints
3) Replacement procedure
See RC-501 Service Manual (Field service)
"3.1.2 Waste toner recycle box"
NOTE
• The steps 1 to 4 are applicable.
2 315
6. OTHERS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
/1050e/1050eP
Blank page
316
Field Service Ver3.0 Nov.2006 7. HOW TO USE THE ADJUSTMENT / SETTING SECTION
1050e/1050eP
7. HOW TO USE THE ADJUST- B. Checkpoints when conducting on-site ser-
317
8. LIST OF ADJUSTMENT ITEMS Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
After PM Implementation
Cleaning web
Adjustment items Replacement parts/Others
Developer
Slit glass
Drum
Machine adjustment Magnification adjustment Regist line speed adjustment
Printer drum clock adjustment (Side1)
Printer horizontal adjustment (Side1)
Scanner drum clock adjustment
ADF drum clock adjustment
Printer drum clock adjustment (Side2)
Printer horizontal clock adjustment (Side2)
Timing adjustment Printer restart timing adjustment (Side1)
Scanner restart timing adjustment
ADF restart timing adjustment
ADF regist loop adjustment
Centering adjustment Printer centering adjustment
ADF Centering adjustment
Warp adjustment Scanner (Glass) warp (Main)
Scanner (Glass) warp (Deputy)
Scanner (ADF) warp (Main)
Scanner (ADF) warp (Deputy)
ADF adjustment ADF density adjustment c
ADF original size adjustment
ADF sensor sensitivity adjustment
ADF incline offset adjustment
ADF centering sensor adjustment
Process High voltage adjustment High voltage auto adjustment
adjustment Drum peculiarity adjustment Blade setting mode e
Auto drum potential adjustment f e
Auto maximum density adjustment g f
Auto dot diameter adjustment h g
LD offset adjustment i h
Auto gamma adjustment (1dot) j i
Cartridge set mode k j
Counter Count PM cycle setting counter reset {
Developer setting counter reset c
Sensitive drum setting counter reset e
Copy count of special parts Fixing cleaning web c
ISW ISW mode
Finisher adjustment Stacker adjustment Paper width adjustment
Paper length adjustment
IP HDD format IP HDD format
Others Setting powder application c c c
Dust-proof glass cleaning (Write unit) d d
Mirror unit positioning (require the jigs)
Blade auto replacement spring charge d
Fusing lamp's installation direction (Maker's mark in front)
Thermistor positioning (require the jig)
Thermostat positioning (require the jig)
Parameter board (PB) replacement
EEPROM replacement
Grip conveyance home sensor adjustment
Trimmer board solenoid operation counter clear
Multi feed detection board adjustment
• When replacing the image processing board (IPB) due to the IPB being damaged, the parameter board (PB)
that was installed on the damaged IPB should be used on the new IPB. Contact the service manager of the
authorized distributor if it is considered that the PB is also damaged.
• The parameter board (PB) stores various adjustment data, setting data and counter data. Therefore, when
replacing the PB, perform all adjustments and settings, and be sure to replace the parts for control correc-
tion (Drum, developer, cleaning blade, cleaning web). For details, contact the service manager of the
authorized distributor.
318 2
Scanner wire · mirror
•
c
h
g
f
e
d
unit
CCD unit
k
j
i
h
g
f
e
d
c
aged.
Write unit
k
j
i
h
g
f
d
e
c
Registration roller
f
e
d
c
Multi feed detection board
/1, /2 (MFDB /1, /2)
{
Field Service Ver3.0 Nov.2006
{
Fusing heater lamp /3 (L4)
{
Thermistor /1 (TH1)
{
Thermistor /3 (TH3)
{
Thermostat /1 (TS1)
{
Thermostat /2 (TS2)
{
High voltage unit /1, /2
c
(HV1, /2)
Overall control board
d
c
(OACB)
Printer control board
{
(PRCB)
Operation board /1
{
(OB1)
RADF control board
c
e
k
d
f
l
j
g
i
h
(RADFCB)
d
f
e
FD control board (FDCB)
c
FNS control board
c
(FNSCB)
{
SD control board
c
(SDCB)
PB control board
c
(PBCB)
2
Trimmer board assembly
{
ADU drive board /1
{
(ADUDB1)
{
8. LIST OF ADJUSTMENT ITEMS
ROM and perform all adjustments for the PB, SD, FD or FS if it is considered that the EEPROM is also dam-
was installed on the damaged control board should be used on the new control board. Install the new EEP-
319
board (FDCB) or the FNS control board (FNSCB) being damaged, the non-volatile memory (EEPROM) that
When replacing a board due to the PB control board (PBCB), the SD control board (SDCB), FD control
bizhub PRO 1050/1050P
1050e/1050eP
9. UTILITY MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
9. UTILITY MODE
9.1 List of utility modes
/1050e/1050eP
Note
• For details on the utility mode, refer to "User's guide."
320 2
Field Service Ver3.0 Nov.2006 9. UTILITY MODE
1050e/1050eP
Adjustment 02 ADF Frame Erasure Setting
03 Non Image Area Erase Setting
07 Size Setting
08 Annotation Setting
09 Perfect Binding Mode Setting
02 Manager/Machine Register 01 Machine Manager Register
03 User Auth./Volume 01 Authentication Method 02 Authentication Setting
Track 02 Section Management Setting
02 Volume Track
03 User Authentication Set
04 Non register/Output Set
04 Network Setting 01 Machine NIC Setting
02 Controller NIC 01 TCP/IP
Setting 02 NetWare
03 IPP
04 FTP
05 SNMP
06 SMB
07 AppleTalk
08 E-Mail 01 E-Mail Send Setting
02 E-Mail Receive Setting
03 Title Setting
04 Sentence Setting
09 HDD
10 Alert Mail
11 CSRC 01 CSRC Send Setting
02 CSRC Receive Setting
03 CSRC Communication Test
12 AP I/F
13 PSWC
14 Network Setting Clear
15 SNMP Trap
05 Copy/Printer Setting 01 Job Offset Operating
02 Continuation print(Print)
03 Page No. pos.(Booklet)
04 Fixing Prerotation Set
05 Image Auto Rotation
06 Interruption Suspend
07 Copy Reserve Operation
08 Scan Stop (pull out tray)
09 Continuation Print (Copy)
2 321
9. UTILITY MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
322
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
This machine is provided with a service mode for var-
ious adjustments/settings. Data adjusted/set in this
mode is stored in the parameter board (PB).
323
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
324
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
09 Cartridge Set Mode
03 Drum Peculiarity Manual
04 User Paper Setting
05 Recall Standard Data
03 Counter 01 PM Count
02 Data Collection 01 Total count of each paper size
02 Copy count of each paper size
03 Print count of each paper size
04 Large size count
05 ADF Count
06 Pixel ratio of each section
07 Pixel ratio ranking list
08 JAM data of time series
09 JAM Count
10 Count of each copy mode
11 SC data of time series
12 SC Count
13 JAM count of each section
14 SC count of each section
03 Parts Counter 01 Count of special parts
02 Count of each parts
04 Machine Condition 01 I/O Check mode
05 List Output 01 List Output
06 Test Mode 01 Test Pattern Output Mode
02 Test Pattern Density
03 Running Test Mode
07 System Setting 01 Software SW Setting
02 Telephone Number Setting
03 M/C Serial Number Setting
04 Setting Date Input
08 ROM Version 01 ROM Version
09 CS Remote Care 01 CS Remote Care 01 E-Mail
02 Modem
10 ISW 01 ISW
11 Finisher Adjustment 01 Stapler Position Adj. 01 Stapling Center Position Adjustment
02 Paper Width Adjustment
02 Multi Folder (Punch) 01 Paper Width Adjustment
Adj. 02 Hole-Punch Vertical Position Adjustment
325
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
326 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Adjust the paper size from tray /1 to tray /5. plate cover [2] and the paper guide [1] until it
This adjustment is needed when a paper size is not reaches the scale "250"[4]. (The scale inside
detected properly. the paper guide is 250 mm)
(1) Procedure
[2] [3] [1]
1. Enter the service mode.
2. "Service mode menu screen"
Press the [01 Machine Adjustment] key.
3. A sub menu appears on the right side of the
screen.
Press the [01 Tray Adjustment] key on the sub
menu.
4. "Tray adjustment screen"
Tray adjustment includes the following items.
Press the [Next] key or the [Back], and select
(1) of the tray you adjust.
[Tray 1 (1)] [4]
[Tray 1 (2)]
[Tray 2 (1)] Info HJG: 250mm
[Tray 2 (2)] 1. 250mm
[Tray 3 (1)] 2. 297mm
[Tray 3 (2)]
[Tray 4 (1)]
[Tray 4 (2)]
[Tray 5 (1)]
[Tray 5 (2)]
[1] 1050fs3021c
Note
• Be sure to select (1) of the tray you adjust. 6. Set the tray.
7. Press the [Start] key on the screen.
Info HJG: The current position of the selected tray is read
Wichtig: Zum Ausführen Justage müssen in. When the adjustment is done, the message
die Papiermagazine eingeschoben sein ! "Complete" appears.
8. Press the [Next] key and select (2) of the trays
you want to adjust.
Note
• Be sure to select (2) of the trays you want
to adjust.
9. Pull out the tray and widen the paper guide to
the max. width. Narrow the paper guide slowly
to fill a gap between the lift plate cover and the
paper guide until it reaches the scale "A3·A4".
(The scale inside the paper guide is 297 mm)
10. Set the tray.
327
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
11. Press the [Start] key on the screen. 10.3.2 Magnification adjustment
The current position of the selected tray is read Adjust various kinds of image magnification.
in. When the adjustment is done, the message
/1050e/1050eP
(1) Procedure
Note
• Select [72-91g] for the basic weight setting.
328 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
even with surrounding area).
Within 102.8 0 mm
-0.5 16. Press the [SERVICE] key.
17. "Regist Line Speed Adjustment screen"
0 Through the numeric keys, enter the adjusted
102.8 -0.5
step number of the output paper you selected
in step 15, and press the [Set] key.
• Setting range:-40 (short) to +55 (long)
1 step = 0.05%
1050fs3001c
Note
• The density of "Test pattern density set-
ting" is reflected. So, be sure to check the
set value of "Test pattern density setting"
to ensure it is "255."
12. Set A3 or 11 x 17 paper (130 g/m2 or 35 lb
Bond) in the tray. Press the Start button to out-
put the test pattern (No.9).
13. Press the [SERVICE] key to return to the [Regist
Line Speed Adjustment] screen.
14. Repeat steps 11 to 13 to output test patterns
for two steps before and after the value you
entered in step 10.
e.g.: When the adjusted value is "-1"
Output 5 test patterns for -3, -2, -1, 0, 1.
1 329
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. Printer drum clock adjustment (Side 1) C. Printer drum clock adjustment (Side 2)
Adjust the magnification of the sub scan direction on Adjust the magnification of the sub scan direction on
only side 1 of the printer system. only side 2 of the printer system.
/1050e/1050eP
This adjustment changes the line speed of the drum This adjustment changes the line speed of the drum
and the registration roller on side 1 evenly. and the registration roller on side 2 evenly.
Info HJG: Maßstab in FD der Seite 1 Info HJG: Maßstab in FD der Seite 2
(1) Procedure (1) Procedure
205.7 1
205.7 1
1050fs3002c
1050fs3003c
8. When the value is not within the standard value,
press the [SERVICE] key. 8. When the value is not within the standard value,
9. "Printer Drum Clock Adjustment <SIDE1> press the [SERVICE] key.
screen" 9. "Printer Drum Clock Adjustment <SIDE2> screen"
Enter a numeric value through the numeric keys Enter a numeric value through the numeric keys
and press the [Set] key. and press the [Set] key.
• Setting range:-10 (short) to +10 (long) • Setting range:-10 (short) to 0 (long)
1 step = 0.05% 1 step = 0.05%
10. Repeat steps 5 to 9 until the standard value 10. Repeat steps 5 to 9 until the standard value
can be obtained. can be obtained.
330
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
This adjustment changes the horizontal magnification This adjustment changes the horizontal magnification
in image processing prior to the laser exposure. in image processing prior to the laser exposure.
Info HJG: Maßstab in CD der Seite 1 Info HJG: Maßstab in CD der Seite 2
(1) Procedure (1) Procedure
190
190
1050fs3004c
1050fs3005c
8. When the value is not within the standard value,
press the [SERVICE] key. 8. When the value is not within the standard value,
9. "Printer Horizontal Adjustment <SIDE1> press the [SERVICE] key.
screen" 9. "Printer Horizontal Adjustment <SIDE2> screen"
Enter a numeric value through the numeric keys Enter a numeric value through the numeric keys
and press the [Set] key. and press the [Set] key.
• Setting range:-10 (short) to +10 (long) • Setting range:-5 (short) to 0 (long)
1 step = 0.1% 1 step = 0.1%
10. Repeat steps 5 to 9 until the standard value 10. Repeat steps 5 to 9 until the standard value
can be obtained. can be obtained.
331
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
This adjustment changes the scanning speed of the This adjustment changes the scanning speed of the
exposure unit. ADF.
Info HJG: Maßstab in FD vom Feeder
Info HJG: Maßstab in FD vom Originalglas
(1) Procedure (1) Procedure
200
1050fs3006c
332 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
A. Printer restart timing adjustment (Side 1) and press the [Set] key.
Adjust the image leading edge timing on only side 1. • Setting range:-30 (short) to +30 (long)
This adjustment changes the laser writing start tim- 1 step = 0.1 mm
ing.
10. Repeat steps 5 to 9 until the standard value
Info HJG: Drucker Neustart - Bildanfang Seite 1
can be obtained.
NOTE
• Be sure the printer drum clock adjustment
(Side 1) has been adjusted. B. Printer restart timing adjustment (Side 2)
Adjust the image leading edge timing on only side 2.
(1) Procedure This adjustment changes the laser writing start tim-
ing.
1. Enter the service mode.
Info HJG: Drucker Neustart - Bildanfang Seite 2
2. "Service mode menu screen" NOTE
Press the [01 Machine Adjustment] key. • Be sure the printer drum clock adjustment
3. A sub menu appears on the right side of the (Side 2) has been adjusted.
screen.
Press the [03 Timing Adjustment] key on the (1) Procedure
sub menu.
1. Enter the service mode.
4. "Timing adjustment menu screen"
Press the [01 Printer Restart Timing Adjustment 2. "Service mode menu screen"
<SIDE1>] key. Press the [01 Machine Adjustment] key.
5. "Printer Restart Timing Adjustment <SIDE1> 3. A sub menu appears on the right side of the
screen" screen.
Tray can be adjusted as a whole and by each Press the [03 Timing Adjustment] key on the
(tray /1 to /5). Press the [Next] or the [Back] key sub menu.
to select the item you adjust, and press the 4. "Timing adjustment menu screen"
[COPY] key. Press the [02 Printer Restart Timing Adjustment
6. Select A3 or 11 x 17 paper. Press the Start but- <SIDE2>] key.
ton to output the test pattern (No.16). 5. "Printer Restart Timing Adjustment <SIDE2>
7. Measure the leading edge timing with a scale. screen"
• Standard value:20 ± 0.5 mm Tray can be adjusted by each (tray /1 to /5).
Press the [Next] or the [Back] key to select the
item you adjust, and press the [COPY] key.
20
6. Select the A3 or 11 x 17 paper. Press the Start
button to output the test pattern (No.16).
1050fs3008c
1 333
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
7. Measure the leading edge timing with a scale. 5. "Printer regist loop adj. screen"
• Standard value:20 ± 0.5 mm Press the [Next] or the [Back] key to select the
item you adjust, and press the [COPY] key.
/1050e/1050eP
Note
• The adjustment values for "Side 1" and
"Side 2" are reflected on the paper weight
50 to 161 g/m2.
• The adjustment values for "Side 1 thick"
1050fs3009c
and "Side 2 thick" are reflected in 162 to
300 g/m2.
8. When the value is not within the standard value,
6. Set the copy according to the item that has
press the [SERVICE] key.
been adjusted and press the Start button to
9. "Printer Restart Timing Adjustment <SIDE2> output a test pattern (No. 16).
screen"
7. When the trouble is not solved, press the
Enter a numeric value through the numeric keys
[SERVICE] key.
and press the [Set] key.
8. "Printer regist loop adj. screen"
• Setting range:-30 (short) to +30 (long)
Enter a numeric value through the numeric keys
1 step = 0.1 mm
and press the [Set] key.
10. Repeat steps 5 to 9 until the standard value
• Setting range:-10 (small) to +10 (large)
can be obtained.
1 step = 1 ms
9. Repeat the steps 5 to 8 until an appropriate
C. Printer regist loop adjustment value is obtained.
Adjust the paper loop amount in the registration roller
section to remove paper skew and wrinkle, or paper
D. Printer pre-regist adjustment
jamming in the registration section.
Adjust the paper loop amount in the pre-registration
Info HJG: Bausch - Registrierrollen
roller section to remove paper skew and wrinkle, or
(1) Procedure
paper jamming in the pre-registration section.
1. Enter the service mode. Info HJG: Bausch - Vor-Registrierrollen
2. "Service mode menu screen" (1) Procedure
Press the [01 Machine Adjustment] key.
1. Enter the service mode.
3. A sub menu appears on the right side of the
2. "Service mode menu screen"
screen.
Press the [01 Machine Adjustment] key.
Press the [03 Timing Adjustment] key on the
3. A sub menu appears on the right side of the
sub menu.
screen.
4. "Timing adjustment menu screen"
Press the [03 Timing Adjustment] key on the
Press the [03 Printer Regist Loop Adjustment]
sub menu.
key.
4. "Timing adjustment menu screen"
Press the [04 Printer Pre-regist Adjustment]
key.
5. "Printer pre-regist adj. screen"
Tray can be adjusted by each (tray /1 to /5).
Press the [Next] or the [Back] key to select the
item you adjust, and press the [COPY] key.
334
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
error (such as missing image portions) occurs.
[SERVICE] key.
8. "Printer pre-regist adj. screen"
Preparation:
Enter a numeric value through the numeric keys
• Select the appropriate paper setting beforehand
and press the [Set] key.
so that the transfer assist sheet (50 to 91 g/m2)
• Setting range:-10 (small) to +10 (large)
can be fed through.
1 step = 1ms
9. Repeat the steps 5 to 8 until an appropriate NOTE
value is obtained.
• Perform "Transfer Assist Pressure Level adj."
properly, or the photoconductor may get
E. Printer lead edge timing adjustment damaged.
Adjust the image erasure amount of the leading edge. • Only perform this adjustment when the trans-
Info HJG: Löschbereich am Bildanfang fer error still occurs after performing "Trans-
(1) Procedure fer Assist Push Position adjustment" and
"Transfer Assist Release Position adj."
1. Enter the service mode. • Always perform "Transfer Assist Push Posi-
2. "Service mode menu screen" tion adjustment" and "Transfer Assist
Press the [01 Machine Adjustment] key. Release Position adj." after performing
3. A sub menu appears on the right side of the "Transfer Assist Pressure Level adj."
screen.
Press the [03 Timing Adjustment] key on the (1) Procedure
sub menu.
1. Enter the service mode.
4. "Timing adjustment menu screen"
2. "Service mode menu screen"
Press the [05 Printer Lead Edge Timing Adjust-
Press the [01 Machine Adjustment] key.
ment] key.
3. A sub menu appears on the right side of the
5. "Printer lead edge timing adjustment screen"
screen.
Press the [COPY] key.
Press the [03 Timing Adjustment] key on the
6. Select A3 or 11 x 17 paper. Press the Start but- sub menu.
ton to output the test pattern (No.16).
4. "Timing adjustment menu screen"
7. Check the printer lead edge timing. Press the [06 Transfer Assistance Timing
• Standard value:within 4 mm Adjustment] key.
8. When the value is not within the standard value, Press the [NEXT] or the [Back] key to select the
press the [SERVICE] key. item to be adjusted, and press [COPY].
9. "Printer lead edge timing adjustment screen" 5. "COPY screen"
Enter a numeric value through the numeric keys Change the print mode to [1 - 2], and select the
and press the [Set] key. tray in which the transfer assist sheet is loaded.
• Setting range:-20 (small) to +40 (large) 6. Press [START] to print the test pattern (No. 16).
1 step = 0.1 mm Print a halftone image or the original as neces-
10. Repeat steps 5 to 9 until the standard value sary.
can be obtained. 7. If the transfer error still occurs, press the
[SERVICE] key.
2 335
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
8. Enter a numeric value through the numeric keys G. Scanner restart timing adjustment
and press the [Set] key. Adjust image leading edge timing of original scanning
• [Transfer Assist Push Position adjustment] from the original glass.
/1050e/1050eP
• [Transfer Assist Release Position adj.] In this adjustment, the starting position for reading
Setting range:-32 (earlier) to +31(later) while in the original scanning mode is adjusted.
1 step = 0.5mm Info HJG: Scanner Neustart
• [Transfer Assist Pressure Level adj.] (1) Procedure vom Originalglas für Bildanfang
Setting range:-10 (pressure amount-low) to
1. Enter the service mode.
+10 (pressure amount-high)
2. "Service mode menu screen"
1 step = 0.1 mm
Press the [01 Machine Adjustment] key.
among pressure amount, pressure point, Press the [03 Timing Adjustment] key on the
ment. If the adjustment value exceeds the 4. "Timing adjustment menu screen"
limit steps, the transfer assist sheet may Press the [07 Scanner Restart Timing Adjust-
contact and damage the photoconductor. ment] key.
(Note that the steps described below are 5. "Scanner (Orig. Glass) restart timing adj.
only used as a guide.) screen"
Press the [COPY] key.
Pressure amount Pressure point Release point
6. Select A3 or 11 x 17 paper, and set the "test
(Step) (Step) (Step)
chart" on the original glass. Press the Start but-
0 -10 +12
ton.
-10 -20 +22
7. Check the leading edge timing.
+10 0 +2 • Standard value:within ± 1.5 mm
8. When the value is not within the standard value,
9. Repeat the steps 4 to 7 until an appropriate press the [SERVICE] key.
value is obtained.
9. "Scanner (Orig. Glass) restart timing adj.
screen"
Enter a numeric value through the numeric keys
and press the [Set] key.
• Setting range:-40 (image, fast) to
+40 (image, slow)
1 step = 0.1 mm
10. Repeat steps 5 to 9 until the standard value
can be obtained.
336 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
In this adjustment, the starting position for reading or original jamming in the registration section.
while in the ADF scanning mode is adjusted. Info HJG: ADF Originalbausch
Info HJG: ADF Neustart - Bildanfang (1) Procedure
(1) Procedure
1. Enter the service mode.
1. Enter the service mode. 2. "Service mode menu screen"
2. "Service mode menu screen" Press the [01 Machine Adjustment] key.
Press the [01 Machine Adjustment] key. 3. A sub menu appears on the right side of the
3. A sub menu appears on the right side of the screen.
screen. Press the [03 Timing Adjustment] key on the
Press the [03 Timing Adjustment] key on the sub menu.
sub menu. 4. "Timing adjustment menu screen"
4. "Timing adjustment menu screen" Press the [09 ADF Regist Loop Adjustment]
Press the [08 ADF Restart Timing Adjustment key.
key. 5. "ADF regist loop adj. screen"
5. "ADF restart timing adj. screen" Press the [Next] or the [Back] key to select the
Press the [Next] or the [Back] key to select the side of original you adjust, and press the
side of original you adjust, and press the [COPY] key.
[COPY] key. The side of original changes as follows:
The side of original changes as follows: SIDE1 → SIDE2
SIDE1 → SIDE2
Note
Note • SIDE 1 represents the front side and SIDE 2
• SIDE 1 represents the front side and SIDE 2 represents the back side.
represents the back side. 6. Select the A3 or 11 x 17 paper, and set the
6. Select A3 or 11 x 17 paper, and set the "adjust- "adjustment chart" on the ADF. Press the Start
ment chart" on the ADF. Press the Start button. button.
7. Check the image leading edge timing. 7. When the ADF regist loop amount is not appro-
• Standard value: ± 2 mm priate, press the [SERVICE] key.
8. When the value is not within the standard value, 8. "ADF regist loop adj. screen"
press the [SERVICE] key. Enter a numeric value through the numeric keys
9. "ADF restart timing adj. screen" and press the [Set] key.
Enter a numeric value through the numeric keys • Setting range:-10 (small) to +10 (large)
and press the [Set] key. 1 step = 0.1 mm
• Setting range:-50 (image, fast) to 9. Repeat the steps 5 to 8 until an appropriate
+50 (image, slow) value is obtained.
1 step = 0.1 mm
10. Repeat steps 5 to 9 until the standard value
can be obtained.
2 337
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
This adjustment changes the laser writing start tim- Info HJG: Scannerzentrierung Originalglas
ing. NOTE
• Be sure the printer centering has been
A. Printer centering adjustment adjusted.
Adjust the mis-centering of images on the printer.
Info HJG: Drucker Zentrierung CD (1) Procedure
NOTE (Siehe untere Info)
1. Enter the service mode.
• Be sure the printer horizontal adjustment
(Side 1) and the printer horizontal adjustment 2. "Service mode menu screen"
(Side 2) have been adjusted. Press the [01 Machine Adjustment] key.
3. A sub menu appears on the right side of the
(1) Procedure screen.
Press the [04 Centering Adjustment] key on the
1. Enter the service mode. sub menu.
2. "Service mode menu screen" 4. "Centering adjustment mode menu screen"
Press the [01 Machine Adjustment] key. Press the [02 Scanner Centering Adjustment]
3. A sub menu appears on the right side of the key and press the [COPY] key.
screen. 5. Select A3 or 11 x 17 paper, and set the "test
Press the [04 Centering Adjustment] key on the chart" on the original glass. Press the Start but-
sub menu. ton.
4. "Centering adjustment mode menu screen" 6. Fold the printed paper into two along the center
Press the [01 Printer Centering Adjustment] key in the main scan direction, and measure how
and press the [COPY] key. much the left and right lines misalign from each
5. Select A3 or 11 x 17 paper. Press the Start but- other.
ton to output the test pattern (No.16). • Standard value: within ± 2 mm
6. Fold the printed paper into two along the center 7. When the value is not within the standard value,
in the main scan direction, and measure how press the [SERVICE] key.
much the left and right lines misalign from each 8. "Scanner (Orig. Glass) centering Adj. screen"
other. Enter a numeric value through the numeric keys
• Standard value: within ± 1.5 mm and press the [Set] key.
7. When the value is not within the standard value, • Setting range:-30 (image in front) to
press the [SERVICE] key. +30 (image in back)
8. "Printer centering adjustment screen" 1 step = 0.1 mm
Enter a numeric value through the numeric keys 9. Repeat steps 5 to 8 until the standard value
and press the [Set] key. can be obtained.
• Setting range:-64 (image in front) to
+63 (image in back)
1 step = 0.1 mm
9. Repeat steps 5 to 8 until the standard value
can be obtained.
Info HJG:
Für die Justage muß DIPSW 12 (Bit 3) auf „1“ gesetzt
werden (Zentrierungssensor ist dann für die
Justage = deaktiviert) !
Nach der Justage muß der Bit wieder auf „0“ gesetzt
werden !
338 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• "Small" represents paper which is smaller
NOTE (Siehe untere Info)
than 300 mm in the sub-scan direction.
• Be sure the printer centering has been However, this excludes A4 or 8.5 x 11 which
adjusted. is automatically adjusted by the centering
sensor.
(1) Procedure • "Large" represents paper which is larger
than 300 mm in the sub-scan direction.
1. Enter the service mode.
However, this excludes A3 or 11 x 17 which
2. "Service mode menu screen"
is automatically adjusted by the centering
Press the [01 Machine Adjustment] key.
sensor.
3. A sub menu appears on the right side of the • When adjusting ADF centering sensor
screen. adjustment (SIDE1:8.5 x 11) and (SIDE1:11 x
Press the [04 Centering Adjustment] key on the 17), change the centering sensor /Fr posi-
sub menu. tion to "LT" side. Then, turn OFF/ON the
4. "Centering adjustment mode menu screen" power switch, and follow the procedure of
Press the [03 ADF Centering Adjustment] key this adjustment. (See chapter III "1.5
and press the [COPY] key. Centering sensor switchover adjustment"
5. "ADF centering adjustment screen" in the Theory of Operation for DF-603)
Press the [Next] or the [Back] key to select the 6. Select paper according to the adjusted item.
item you adjust, and press the [COPY] key. Set the "adjustment chart" on the ADF and
The item switches as follows: press the Start button.
ADF Centering Adjustment (SIDE1:Small)
7. Fold the printed paper into two along the center
↓
in the main scan direction, and measure how
ADF Centering Adjustment (SIDE2:Small)
much the left and right lines misalign from each
↓
other.
ADF Centering Adjustment (SIDE1:Large)
• Standard value: within ± 2 mm
↓
8. When the value is not within the standard value,
ADF Centering Adjustment (SIDE2:Large)
press the [SERVICE] key.
↓
9. [ADF centering adjustment screen]
ADF Centering Sensor Adjustment (SIDE1:A4)
Enter a numeric value through the numeric keys
or (SIDE1:8.5 x 11)*1
and press the [Set] key.
↓
• Setting range:-30 (image in front) to
ADF Centering Sensor Adjustment (SIDE1:A3)
+30 (image in back)
or (SIDE1:11 x 17)*1
1 step = 0.1 mm
*1 When the power switch is ON, the ADF's 10. Repeat steps 5 to 9 until the standard value
centering correction sensor /Fr position is can be obtained.
automatically detected and displayed.
Info HJG:
Formate A4 und A3 werden automatisch
über den Centringsensor justiert (siehe bei Note)
2 339
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
340
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
message will be displayed. with electrical conductive material, The way it refracts
light from the exposure lamp is different from that of
(1) Error message 1 the original glass. Thus, perform this adjustment
when replacing the slit glass.
Adjust for Moderate Brightness. Info HJG: Belichtungsintensität
The Non-image area erase function may not Preparation: über ADF für die kleine Glasplatte
operate correctly with dark (density) origi- • Clean the slit glass.
nals. • Make sure the white chart is not dirty. (Partial dirt
can be ignored)
Handling 1
When the non-image area erase function is not used (1) Procedure
very frequently, or when copy originals that have a
1. Enter the service mode.
dark background are not copied very frequently in
non-image area erase, the copier can be used in the 2. "Service mode menu screen"
current installation location. However, when copy Press the [01 Machine Adjustment] key.
originals that have a dark background are frequently 3. A sub menu appears on the right side of the
copied, install the copier in a location where less screen.
external light gets in (darker) than the present loca- Press the [07 ADF Adjustment] key on the sub
tion, and check the non-image area erase check menu.
mode again. 4. "ADF adjustment mode menu screen"
Press the [01 ADF Density Adjustment] key.
(2) Error message 2 5. "ADF density adjustment screen"
Set the "white chart" on the ADF.
Adjust for Extreme Brightness.
In many case, the non-image area erase Note
function will not operate correctly. • Set the "white chart" in the A4-direction.
6. Press the [Start] key.
Handling 2
The white chart is scanned, and density is
When the non-image area erase function is not
automatically adjusted.
used very frequently, the copier can be used in
7. When an error message appears, turn OFF/ON
the current installation location. However, if the
the power switch (SW2) of the main body.
non-image area erase function is frequently
Repeat steps 1 to 6 until it is completed prop-
used, install the copier in a location where less
erly.
external light gets in (darker) than the present
location, and check the non-image area erase
check mode again. At this time, when there is a
B. ADF original size adjustment
bright light source such as a fluorescent light
Conduct this adjustment when the ADF original size is
installed directly above the copier, reconsider the
not properly detected.
installation location, or take some measures to
shield the light source and check the mode Info HJG:
(1) Procedure ADF Originalformaterkennung
again.
1. Enter the service mode.
2. "Service mode menu screen"
Press the [01 Machine Adjustment] key.
1 341
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3. A sub menu appears on the right side of the 5. "ADF sensor sensitivity adjustment screen"
screen. Press the [Start] key.
Press the [07 ADF Adjustment] key on the sub The ADF sensor sensitivity is automatically
/1050e/1050eP
1050fs3026c
342
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• Setting range:-60 (counterclockwise) to
+60 (clockwise)
1 step = 0.05%
10. Repeat steps 5 to 9 until the standard value
can be obtained.
(1) Procedure
[2] [3]
343
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
8. "ADF Centering Sensor Adj. (A4) screen" 10.3.8 Recall standard data
Press the [Start] key. Sensitivity of the sensor is Reset the adjustment values of the machine adjust-
adjusted, and message of completion is dis- ment to the factory initial data or the installation initial
/1050e/1050eP
Note
• Selecting [Factory initial data] recalls the
factory initial data.
[4] [1] 1050fs3024c • Selecting [Installation initial data] recalls
11. "ADF Centering Sensor Adj. (8.5 x 11) screen" the adjustment values stored when code
Press the [Start] key. Sensitivity of the sensor is "91" of the I/O check mode was conducted.
adjusted, and message of completion is dis- • When selecting [Data at shipment] or [Data
played. at installation], the data returns with no dis-
play changed on the screen.
12. Replace the sensor plate to the position of orig-
inal size (A4 or 8.5 x 11) that the customer
mainly uses. Info HJG:
Erfolgte Änderung im Speicher sichern
Servicemode
04 Machine condition
01 I/O check Mode
Eingabe “9” u. “1” <091-00>
344 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
H. Transfer guide confirm
10.4.1 High voltage adjustment Do not use this adjustment in the field.
Adjust various high voltage values.
Preparation:
• The photo conductor section must be set.
(1) Procedure
NOTE
• When an error message appears during the
adjustment, check to see if the error unit is
properly installed and cleaned. Conduct the
adjustment again.
B. HV adjustment (Charge)
Do not conduct this adjustment in the field.
C. HV adjustment (Transfer)
Do not conduct this adjustment in the field.
345
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
key.
A. Blade setting mode
5. "Auto drum potential adjustment screen"
Perform this adjustment when changing the cleaning
Press the [Start] key. After the automatic
blade. In this mode, apply toner to the cleaning blade
adjustment, the message of completion
and drum, to prevents damages to them.
appears.
Info HJG: nur bei Cleaningblade Wechsel
NOTE machen. Achtung, siehe untere Info ! NOTE
• Perform this only when changing the cleaning • When the following error messages appear,
blade. Otherwise, the cleaning blade special check to see if the drum potential sensor
parts counter is reset, thus making it impos- (DPS) is properly installed and cleaned. Con-
sible to implement the auto blade change in duct the adjustment again.
the right timing. 1) Error 1
• Apply setting powder to the cleaning blade In the 0V check of the DPS, voltage over
and drum. 100V is detected 5 times or more.
2) Error 2
(1) Procedure The drum potential after laser exposure is
detected to be over 350V, and it is deter-
1. Enter the service mode.
mined that control patch detect signal is
2. "Service mode menu screen" not outputted.
Press the [02 Process Adjustment] key. 3) Error 3
3. A sub menu appears on the right side of the Drum potential has been corrected 10 or
screen. more times, but it does not converge.
Press the [02 Drum Peculiarity Adj.] key on the
sub menu. C. Auto maximum density adjustment
4. "Drum peculiarity adjustment mode menu Automatically adjust maximum density of images.
screen" Info HJG: Max. Kontrast - Dmax Sensor Justage
Press the [01 Blade Setting Mode] key. (1) Procedure
5. "Blade setting mode screen"
1. Enter the service mode.
Press the [Start] key. With toner applied, the
2. "Service mode menu screen"
drum is cleaned with the cleaning blade. The
Press the [02 Process Adjustment] key.
message of completion appears.
3. A sub menu appears on the right side of the
screen.
B. Auto drum potential adjustment Press the [02 Drum Peculiarity Adj.] key on the
Measure the charging potential of drum, and adjust sub menu.
automatically the developing bias value, charging 4. "Drum peculiarity adjustment mode menu
voltage and grid voltage. screen"
Press the [03 Auto Maximum Density Adjust-
(1) Procedure ment] key.
5. "Auto maximum density adjustment screen"
1. Enter the service mode.
Press the [Start] key.
2. "Service mode menu screen"
Press the [02 Process Adjustment] key. NOTE
3. A sub menu appears on the right side of the • When the following error messages appear,
screen. check to see if the toner control sensor board
Press the [02 Drum Peculiarity Adj.] key on the (TCSB) is properly installed and cleaned.
sub menu. Conduct the adjustment again.
Info HJG:
346 Achtung, nur bei Cleaningblade Wechsel machen. Sonst wird beim Ausführen nur der
Zähler auf „0“ gesetzt, aber das Cleaningblade bleibt in vorheriger Position.
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
10 or more times, but it does not con- (1) Procedure
verge.
1. Enter the service mode.
2) Error 2
The auto maximum density adjustment is 2. "Service mode menu screen"
not completed, when the developing roller Press the [02 Process Adjustment] key.
rotation speed reaches the specified 3. A sub menu appears on the right side of the
value. screen.
3) Error 3 Press the [02 Drum Peculiarity Adj.] key on the
No signal is outputted from the maximum sub menu.
density sensor. Control patch detect sig- 4. "Drum peculiarity adjustment mode menu
nal is not outputted. screen"
Press the [05 LD Offset Adjustment] key.
D. Auto dot diameter adjustment 5. "LD offset adjustment screen"
Automatically adjust the diameter of laser beam. Press the LD1 offset line speed [490 mm] key,
Info HJG: Punktdurchmesser and press the [COPY] key.
(1) Procedure
6. Select A3 or 11 x 17 paper, and press the Start
1. Enter the service mode. button to output a test pattern.
2. "Service mode menu screen" 7. Adjust laser intensity of LD1 and LD2.
Press the [02 Process Adjustment] key. Standard value: Compare image patterns cre-
ated by the LD1 and LD2. Confirm that density
3. A sub menu appears on the right side of the
is uniform (± 1 gap is OK) as per the following
screen.
figure, and the highlighted patterns start
Press the [02 Drum Peculiarity Adj.] key on the
between the two reference lines.
sub menu.
4. "Drum peculiarity adjustment mode menu
screen"
Press the [04 Auto Dot Diameter Adjustment]
key. [1]
5. "Auto dot diameter adjustment screen"
Press the [Start] key.
NOTE
• When the following error messages appear,
check to see if the toner control sensor board
(TCSB) is properly installed and cleaned.
Conduct the adjustment again.
1) Error 1
The gamma sensor (on the TCSB) dirt cor-
rection has been corrected 10 or more LD1 LD2 LD1 LD2 LD1 LD2 LD1 LD2
347
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
348 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
10.4.4 User paper setting data.
Use this adjustment when the transfer and separation
functions do not work satisfactorily with the standard A. Procedure
adjustments because of using special papers, etc.
1. Enter the service mode.
This setting is applied when you select [User] as the
paper type. 2. "Service mode menu screen"
By default, the following data are inputted. Press the [02 Process Adjustment] key.
2 3. A sub menu appears on the right side of the
• For Japan: 62 to 71 g/m Normal paper
2 screen.
• For inch area: 72 to 91 g/m Normal paper
2 Press the [05 Recall Standard Data] key on the
• For metric area: 72 to 91 g/m Normal paper
sub menu.
NOTE 4. "Recall standard data (Process adjustment)
• Input data according to instructions of KMBT screen"
field support section. Press the [Factory initial data] or the [Installation
initial data] key.
A. Procedure
Note
1. Enter the service mode.
• Selecting [Factory initial data] recalls the
2. "Service mode menu screen" factory initial data.
Press the [02 Process Adjustment] key. • Selecting [Installation initial data] recalls
3. A sub menu appears on the right side of the the adjustment values stored when code
screen. "91-00" of the I/O check mode was con-
Press the [04 User Paper Setting] key on the ducted.
sub menu. • When selecting [Data at shipment] or [Data
4. "User Paper Setting screen" at installation], the data returns with no dis-
Select one of the followings; [User Paper 1] / play changed on the screen.
[User Paper 2] / [User Paper 3]
Press the [Next] and [Back] key to select an
item you adjust.
5. Input data for the selected item, and press the
[Set] key.
6. Repeat steps 4 and 5 to configure other items.
2 349
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
10.5.1 PM count
1. Enter the service mode.
Configure the reset and cycle of the PM count, devel-
oper count and drum count. 2. "Service mode menu screen"
Press the [03 Counter] key.
NOTE 3. A sub menu appears on the right side of the screen.
• The PM count is different in the count con- Press the [01 PM Count] key on the sub menu.
dition depending on the setting of DIPSW8- 4. "PM count/cycle screen"
6. Press the key for an item you reset, and press
When set to "0": 1 count for a single side of the [Count Reset] key.
each large paper exit, and 5. "Reset confirm screen"
2 counts for a double side. Press the [Yes] key to reset the counter.
When set to "1": 2 counts for a single side The counter is reset, and the start date is auto-
of each large paper exit matically inputted.
(the definition of large size Press the [No] key not to reset the counter. You
paper is set by DIPSW10-3 return to the "PM count/cycle screen."
and 4), and 4 counts for a
6. "PM count/cycle screen"
double side. For those
Pressing the [OK] key validates resetting.
other than the large size,
Pressing the [Cancel] key invalidates the count
the count is same as when
reset.
set to "0."
• The developer count and the sensitive drum
count are made at all times 1 count for a sin-
gle side and 2 counts for a double side for a
small size paper, 2 counts for a single count
and 4 counts for a double count for a large
size paper.
A. Counter reset
Reset the PM count, developer count and drum
count.
NOTE
• Be sure to reset the PM count after imple-
menting a periodic check (every 750,000
prints).
Otherwise, the periodic check alert message
and icon do not disappear.
• Be sure to reset the developer count after
replacing a developer. Otherwise, gray back-
ground image and toner scatter may occur.
Also, the “Drum/Deve” icon on the user
screen does not disappear.
• Be sure to reset the sensitive drum count
after replacing a drum. Otherwise, image gray
background and toner scatter may occur.
350 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
by the CS Remote Care, list output and the mail
NOTE remote notification system.
• The PM cycle, developer cycle and drum
cycle are already inputted in the initial set- A. Confirmation method
tings. Usually, do not change these settings. (1) Procedure
351
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• The [Count Reset] key is shown in the indi-
vidual data confirmation screen of the [13
JAM count of each section] and the [14 SC
count of each section].
When pressing the [Count Reset] key,
"Count reset confirmation screen" is
shown, and when pressing the [Yes] key,
the section data is reset. Pressing the [No]
key returns to "Individual data confirmation
screen" with the interval data not reset.
Reset these data while in the PM imple-
mentation to confirm the jam or SC occur-
rence count after it was visited last time.
352
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Note
• Maximum count: 99,999,999
• 1 count is made for paper of all types regardless of the paper size.
• All size of paper not included in the below table are counted as special. However, wide paper and
R-direction paper are counted as the same size.
Example: A4W and A4S are counted as A4.
• 8K is counted as B4, and 16K is counted as B5.
Note
• Maximum count: 99,999,999
• Definition of the large size can be changed by DIPSW10-3, 4 (A3, 11 x 17, 12 x 18 for default).
353
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Maximum count: 99,999,999
• No.1, 2 are not counted as No.3 to 8.
354
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Note
• This pixel ratio is a calculated value based on the colored area and the transfer paper area, and is
different from the print ratio when actually printed.
4 03 Print count 3
5 04 Print count 4
6 05 Print count 5
7 06 Print count 6
8 07 Print count 7
9 08 Print count 8
10 09 Print count 9
11 0A Print count 10
12 0B Print count 11
13 0C Print count 12
14 0D Print count 13
15 0E Print count 14
16 0F Print count 15
17 10 Print count 16
18 11 Print count 17
19 12 Print count 18
20 13 Print count 19
21 14 Print count 20
22 15 Print count 21
23 16 Print count 22
24 17 Print count 23
25 18 Print count 24
26 19 Print count 25
27 1A Print count 26
28 1B Print count 27
29 1C Print count 28
30 1D Print count 29
31 1E Print count 30 Oldest data
355
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• This pixel ratio is a calculated value based on the colored area and the transfer paper area, and is
different from the print ratio when actually printed.
NO. CSRC parameter Pixel ratio Print Paper Size Mode Date Remark
(V1) (%) Quantity
1 00 Displaying Displaying Copier or
2 01 up to the first the number Printer
3 02 place of a of papers
decimal
4 03
point
5 04
6 05
7 06
8 07
9 08
10 09
11 0A
12 0B
13 0C
14 0D
15 0E
356
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
code (except idling JAM).
34 21 J18-08 Tray /5
35 22 J21-01 Sensitive drum
NOTE
36 23 J31-01 Registration
• Maximum count: 999,999
37 24 J31-02
38 25 J32-01 Fixing/exit
NO. CSRC Jam code is shown on Section
39 26 J32-02
parameter the operation panel when
40 27 J32-03
(J0) DIPSW11-7 is set to 1
41 28 J32-04
1 00 J11-01 Tray /1
42 29 J32-05
2 01 J11-02
43 2A J32-06
3 02 J11-03
44 2B J92-01 ADU
4 03 J11-04
45 2C J92-02
5 04 J12-01 Tray /2
46 2D J93-01
6 05 J12-02
47 2E J94-01
7 06 J12-03
48 2F J19-01 Paper feed con-
8 07 J12-04
veyance
9 08 J13-01 Tray /3
49 30 J19-02 PF
10 09 J13-02
50 31 J51-01 Main body
11 0A J13-03
51 32 J61-01 DF
12 0B J13-04
52 33 J61-02
13 0C J14-01 Tray /4
53 34 J62-01
14 0D J14-02
54 35 J62-02
15 0E J14-03
55 36 J62-03
16 0F J15-01 Tray /5
56 37 J62-04
17 10 J15-02
57 38 J62-05
18 11 J15-03
58 39 J62-06
19 12 J15-04
59 3A J62-07
20 13 J17-01 Paper feed
60 3B J62-08
21 14 J17-02 conveyance
61 3C J62-09
22 15 J17-03
62 3D J62-10
23 16 J17-04
63 3E J63-01
24 17 J17-05
64 3F J63-02
25 18 J17-06
65 40 J63-03
26 19 J17-12
66 41 J63-04
27 1A J18-01 Tray /3
67 42 J63-05
28 1B J18-02
68 43 J63-06
29 1C J18-03 Tray /4
69 44 J63-07
30 1D J18-04 Tray /5
70 45 J63-08
31 1E J18-05
71 46 J63-09
32 1F J18-06 Tray /3
72 47 J63-10
33 20 J18-07 Tray /4
73 48 J63-11
357
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
NO. CSRC Jam code is shown on Section NO. CSRC Jam code is shown on Section
parameter the operation panel when parameter the operation panel when
(J0) DIPSW11-7 is set to 1 (J0) DIPSW11-7 is set to 1
/1050e/1050eP
358 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
156 9B J74-33 LS 197 C4 J74-90 PB
157 9C J74-34 198 C5 J74-91
158 9D J74-35 199 C6 J74-92
159 9E J74-36 200 C7 J74-93
160 9F J74-37 201 C8 J74-96
161 A0 J74-38 202 C9 J74-97
162 A1 J74-39 203 CA J74-98
163 A2 J74-40 204 CB J74-99
164 A3 J74-41
165 A4 J74-42
166 A5 J74-49
167 A6 J74-60 PB
168 A7 J74-61
169 A8 J74-62
170 A9 J74-63
171 AA J74-64
172 AB J74-65
173 AC J74-66
174 AD J74-67
175 AE J74-68
176 AF J74-69
177 B0 J74-70
178 B1 J74-71
179 B2 J74-72
180 B3 J74-73
181 B4 J74-74
182 B5 J74-75
183 B6 J74-76
184 B7 J74-77
185 B8 J74-78
186 B9 J74-79
187 BA J74-80
188 BB J74-81
189 BC J74-82
190 BD J74-83
191 BE J74-84
192 BF J74-85
193 C0 J74-86
194 C1 J74-87
195 C2 J74-88
196 C3 J74-89
2 359
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Maximum count: 99,999,999
360
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
38 25 Cover sheet
39 26 Trimmer
40 27 Real size copy
41 28 Preset magnification E4
42 29 Preset magnification E3
43 2A Preset magnification E2
44 2B Preset magnification E1
45 2C Preset magnification R4
46 2D Preset magnification R3
47 2E Preset magnification R2
48 2F Preset magnification R1
49 30 Preset Zoom 1
50 31 Preset Zoom 2
51 32 Preset Zoom 3
52 33 ZOOM
53 34 Vertical/Horizontal ZOOM
54 35 Maximum ZOOM
55 36 Minimum ZOOM
56 37 APS
57 38 AMS
58 39 Auto density
59 3A Preset density level 1
60 3B Preset density level 2
61 3C Interrupted copy
62 3D Auto image rotation cancellation
63 3E Sheet insertion
64 3F Chapter control
65 40 Combination
66 41 Booklet copy
67 42 OHP interleave copy
68 43 OHP interleave blank
69 44 Image insert
70 45 Book copy
71 46 Program job
72 47 Non-image area erase
73 48 Neg-/Positive reverse
74 49 Auto repeat
75 4A Manual repeat
76 4B Standard size repeat
77 4C Frame erasure
78 4D Fold erasure
361
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
80 4F All-image area
81 50 Image shift
82 51 Reduction shift
83 52 Overlay
84 53 Watermark
85 54 Stamp
86 55 Date/Time
87 56 Page
88 57 Numbering
89 58 Set quantity 1
90 59 Set quantity 2-5
91 5A Set quantity 6-10
92 5B Set quantity 11 or more
93 5C Time while power remote 1 is On Accumulation of time during which the overall
control board/image processing board is pow-
ered (main power switch is ON). (in minutes)
94 5D Time while power remote 2 is On Time during which the main relay is ON. (in minutes)
95 5E Time while power remote 3 is On Time during which the power control signal
(REM3) is ON. (in minutes)
96 5F Time while power remote 4 is On Time during which the power control signal
(REM4) is ON. (in minutes)
97 60 Time during Low Power mode Time in the LOW POWER mode. (in minutes)
98 61 Time during warm up time Time for warm-up, except print ready time.
(in minutes)
99 62 Time during which the front door is Time during which the front door is open.
open (in seconds)
100 63 Ope.time in 1side straight exit Time from the start of print and the end of
101 64 Ope.time in 1side reverse exit print. (in seconds)
102 65 Operation time in 2side print (Down time due to jam omitted)
103 66 Operation time in ADF mode Time during which ADF operates. (in seconds)
104 67 Morning correction count Counts 1 per image stabilization control (fix-
ing temperature is 50°C or lower)
105 68 Time during APS sensor On Time during which the APS sensor is ON.
(in seconds)
106 69 —
107 6A —
108 6B N of folding & stapling used jobs
109 6C N of ADF special error 5 occurred Number of ADF double feed detection
110 6D N of ADF NF occurred Number of ADF no feed detection
111 6E N of ADF special error 1 occurred Number of wrong detection of original size
112 6F N of ADF special error 2 occurred Number of wrong detection of next original
information
362
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
size mode is not allowed
114 71 N of scanner scanned Counts 1 for pressing Start button in the
platen mode
115 72 N of electrode cleaned
116 73 N of memory overflow Sum of No.124, 125, 126 plus HDD mem-
ory shortage
117 74 N of fixing alarm occurred
118 75 N of no toner stop occurred
119 76 N of AGC retry
120 77 Multi letter tray full alarm
121 78 N of mis-centering correct error
122 79 N of ADF distortion adjust error
123 7A N of ADF distortion data error
124 7B Compression memory overflow Scanner compression/print compression
memory shortage
125 7C Page memory overflow (scan) Shortage in memory for receiving print data
126 7D Page memory overflow (print) Decompression page memory shortage
127 7E Staple Finisher main tray alarm
128 7F Staple Finisher staple alarm
129 80 Saddle Stitcher trash full alarm
130 81 N of ADF special error 4 occurred Ready timeout error
131 82 Store for HDD (Sync.with Copying)
132 83 Store for HDD (Store Scan → HDD)
133 84 Store for PC (Store Scan → PC)
134 85 Store for PC (Store HDD → PC)
135 86 Recall from HDD (Recall HDD)
136 87 Recall from PC (PC/JobEditer)
137 88 Saddle Stitcher staple alarm
138 89 Wide paper count (A3W or 11 x 17W)
139 8A Wide paper count (A4W or 8.5 x 11W)
140 8B Wide paper count (A4SW or 8.5 x 11SW)
141 8C Wide paper count (A5W or 5.5 x 8.5W)
142 8D Wide paper count (Others)
143 8E Hole-Punch
144 8F Z-Folding
145 90 Multi Folder trash full alarm
146 91 Mixplex (Simplex)
147 92 Mixplex (Duplex)
148 93 Right/Left binding originals
149 94 Upper binding originals
150 95 Inside print multi letter
363
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
364 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
194 C1 Number of perfect binding cover Number of books created by perfect bind-
ing machine.
195 C2 Number of perfect binding cover with Number of books when cover paper trim-
trim ming is set.
196 C3 Number of perfect binding cover Number of books when cover paper trim-
without trim ming is not set.
197 C4 Number of ejected paper on the sub
tray (perfect binding)
198 C5 Number of ejected paper on the
stacker (perfect binding)
199 C6 Number of times PB tray is pulled
200 C7 Number of times PB front door is
opened/closed
201 C8 Number of times PB upper door is
opened/closed
2 365
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(10) Data collection No. 12, 14: SC count, SC NO. CSRC SC code Section
count of each section parameter
Confirm the number of SC occurrence of each SC (E0/E1)
/1050e/1050eP
code.
28 1B SC21-04 Transfer/separation
29 1C SC21-05 cleaning motor
NOTE
30 1D SC21-06 abnormality
• Maximum count: 99,999,999
• When the service mode DIPSW3-1 is 1 31 1E SC21-07 Transfer assist motor
(Latched), SC34, 35, 36, 23-14 and 23-17 are 32 1F SC21-08 abnormality
not counted. 33 20 SC23-01 Toner bottle motor
abnormality
NO. CSRC SC code Section
34 21 SC23-02 Developing motor
parameter
abnormality
(E0/E1)
35 22 SC23-03 Blade motor abnor-
1 00 SC13-01 Paper feed motor
36 23 SC23-04 mality
abnormality
2 01 SC13-02 Paper feed motor 37 24 SC23-05
abnormality (PF) 38 25 SC23-06
3 02 SC13-03 Vertical conveyance 39 26 SC23-07
motor abnormality 40 27 SC23-08
(PF) 41 28 SC23-09
4 03 SC13-05 Exit conveyance motor 42 29 SC23-10 Drum motor abnormality
abnormality (PF)
43 2A SC23-11 Toner supply abnor-
5 04 SC18-11 Tray /1 abnormality 44 2B SC23-12 mality
6 05 SC18-12 45 2C SC23-13
7 06 SC18-13 46 2D SC23-14
8 07 SC18-10 47 2E SC23-15
9 08 SC18-21 Tray /2 abnormality 48 2F SC23-17
10 09 SC18-22 49 30 SC23-20
11 0A SC18-23 50 31 SC23-21
12 0B SC18-20 51 32 SC23-22
13 0C SC18-31 Tray /3 abnormality 52 33 SC23-24
14 0D SC18-32 53 34 SC23-25
15 0E SC18-33 54 35 SC23-26
16 0F SC18-30 55 36 SC24-01 Drum temperature
17 10 SC18-41 Tray /4 abnormality 56 37 SC24-02 sensor abnormality
18 11 SC18-42 57 38 SC28-01 High voltage abnor-
19 12 SC18-43 58 39 SC28-02 mality
20 13 SC18-40 59 3A SC28-03
21 14 SC18-51 Tray /5 abnormality 60 3B SC28-04
22 15 SC18-52 61 3C SC29-01 Process abnormality
23 16 SC18-53 62 3D SC29-02
24 17 SC18-50 63 3E SC29-03
25 18 SC21-01 Charger cleaning 64 3F SC29-04
26 19 SC21-02 motor abnormality
65 40 SC29-05
27 1A SC21-03 66 41 SC29-06
366
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
67 42 SC29-07 Process abnormality 108 6B SC32-33 Fan abnormality
68 43 SC29-08 109 6C SC32-34
69 44 SC29-09 110 6D SC32-35
70 45 SC29-10 111 6E SC32-36
71 46 SC29-11 112 6F SC32-37
72 47 SC29-12 High voltage abnor- 113 70 SC32-38
73 48 SC29-13 mality 114 71 SC32-39
74 49 SC29-14 115 72 SC32-40
75 4A SC29-15 116 73 SC32-41
76 4B SC29-16 117 74 SC32-42
77 4C SC32-01 Fan abnormality 118 75 SC32-43
78 4D SC32-02 119 76 SC32-44
79 4E SC32-03 120 77 SC32-45
80 4F SC32-04 121 78 SC32-46
81 50 SC32-05 122 79 SC32-47
82 51 SC32-06 123 7A SC32-48
83 52 SC32-07 124 7B SC32-49
84 53 SC32-09 125 7C SC32-50
85 54 SC32-10 126 7D SC32-51
86 55 SC32-11 127 7E SC32-52
87 56 SC32-12 128 7F SC32-53
88 57 SC32-13 129 80 SC32-54
89 58 SC32-14 130 81 SC32-55
90 59 SC32-15 131 82 SC33-01 ADU drive board
91 5A SC32-16 132 83 SC33-02 abnormality
92 5B SC32-17 133 84 SC33-04 Printer control board
93 5C SC32-18 134 85 SC33-05 abnormality
94 5D SC32-19 135 86 SC33-06
95 5E SC32-20 136 87 SC34-01 Fusing abnormality
96 5F SC32-21 137 88 SC34-02
97 60 SC32-22 138 89 SC34-03
98 61 SC32-23 139 8A SC34-04
99 62 SC32-24 140 8B SC35-01
100 63 SC32-25 141 8C SC35-02
101 64 SC32-26 142 8D SC36-01
102 65 SC32-27 143 8E SC36-02
103 66 SC32-28 144 8F SC36-03
104 67 SC32-29 145 90 SC36-04
105 68 SC32-30 146 91 SC36-05
106 69 SC32-31 147 92 SC36-06
107 6A SC32-32
367
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
368
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
230 E5 SC52-11 Fan abnormality 268 0B SC70-01 Communication
231 E6 SC52-12 269 0C SC70-02 abnormality
232 E7 SC53-01 Fusing motor abnormality 270 0D SC76-01 LS abnormality
233 E8 SC53-02 Total count abnormality 271 0E SC76-02
234 E9 SC53-03 272 0F SC76-03
235 EA SC53-04 Key counter abnormality 273 10 SC76-04
236 EB SC53-05 274 11 SC76-05
237 EC SC53-06 Power source abnor- 275 12 SC76-06
238 ED SC53-07 mality 276 13 SC76-07
239 EE SC53-08 277 14 SC76-08
240 EF SC53-11 Paper feed abnormality 278 15 SC76-09
241 F0 SC53-12 279 16 SC76-10
242 F1 SC53-13 280 17 SC76-11
243 F2 SC53-14 281 18 SC76-31
244 F3 SC53-15 PF paper feed abnor- 282 19 SC76-32
245 F4 SC53-16 mality 283 1A SC76-33
246 F5 SC53-17 Printer control board 284 1B SC76-34
abnormality 285 1C SC76-35
247 F6 SC53-18 Erase lamp abnormality 286 1D SC76-36
248 F7 SC53-19 Conveyance motor 287 1E SC76-37
abnormality 288 1F SC76-38
249 F8 SC53-20 ADU reverse paper 289 20 SC76-39
exit motor abnormality
290 21 SC76-40
250 F9 SC60-01 DF abnormality
291 22 SC76-41
251 FA SC60-02
292 23 SC77-01 FS abnormality
252 FB SC60-03
293 24 SC77-02
253 FC SC60-11
294 25 SC77-03
254 FD SC67-01
295 26 SC77-04
255 FE SC67-02
296 27 SC77-05
256 FF SC67-03
297 28 SC77-06
257 00 SC67-04
298 29 SC77-07
258 01 SC67-05
299 2A SC77-08
259 02 SC67-06
300 2B SC77-11
260 03 SC67-07
301 2C SC77-12
261 04 SC67-08
302 2D SC77-15
262 05 SC67-09
303 2E SC77-21
263 06 SC67-10
304 2F SC77-22
264 07 SC67-11
305 30 SC77-25
265 08 SC67-12
306 31 SC77-28
266 09 SC67-13
267 0A SC67-14
369
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
370 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
386 81 SC49-08 IC abnormality 427 AA SC78-38 PB abnormality
387 82 SC49-09 428 AB SC78-39
388 83 SC49-10 429 AC SC78-40
389 84 SC77-91 SD abnormality 430 AD SC78-41
390 85 SC23-50 Main body abnormality 431 AE SC78-42
391 86 SC78-01 PB abnormality 432 AF SC78-43
392 87 SC78-02 433 B0 SC78-44
393 88 SC78-04 434 B1 SC78-45
394 89 SC78-05 435 B2 SC78-46
395 8A SC78-06 436 B3 SC78-47
396 8B SC78-07 437 B4 SC78-48
397 8C SC78-08 438 B5 SC78-49
398 8D SC78-09 439 B6 SC78-50
399 8E SC78-10 440 B7 SC78-51
400 8F SC78-11 441 B8 SC78-52
401 90 SC78-12 442 B9 SC78-53
402 91 SC78-13 443 BA SC78-54
403 92 SC78-14 444 BB SC78-55
404 93 SC78-15 445 BC SC78-56
405 94 SC78-16 446 BD SC78-57
406 95 SC78-17 447 BE SC78-58
407 96 SC78-18 448 BF SC78-59
408 97 SC78-19 449 C0 SC78-60
409 98 SC78-20 450 C1 SC78-61
410 99 SC78-21 451 C2 SC78-62
411 9A SC78-22 452 C3 SC78-63
412 9B SC78-23 453 C4 SC78-64
413 9C SC78-24 454 C5 SC78-91
414 9D SC78-25 455 C6 SC78-92
415 9E SC78-26 456 C7 SC78-93
416 9F SC78-27 457 C8 SC78-94
417 A0 SC78-28 458 C9 SC78-96
418 A1 SC78-29 459 CA SC78-97
419 A2 SC78-30 460 CB SC78-98
420 A3 SC78-31 461 CC SC78-99
421 A4 SC78-32 462 CD SC80-46
422 A5 SC78-33
423 A6 SC78-34
424 A7 SC78-35
425 A8 SC78-36
426 A9 SC78-37
2 371
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
372
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
Note
1050e/1050eP
• Be sure to reset the fixing cleaning web counter (No.001) after replacing the cleaning web. Other-
wise, fuser cleaning trouble may occur.
• Be sure to perform the blade set mode of the service mode after replacing the cleaning blade. This
automatically resets the cleaning blade counter (No.002). Otherwise, the auto blade replacement
cannot be implemented.
373
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
024 17 Toner supply sleeve /2 55VA-335 1 count for each paper exit in the single side
025 18 Cleaner toner tray 56UA-568 mode, 2 counts in the double side mode.
026 19 Fur brush scraper 56UA-561
027 1A Heat sleeve (Heated) 26AA5315
028 1B Heat roller bearing 56UA7507
029 1C Upper roller sensor 55VA8804
030 1D Heat roller sensor 55VA8806
031 1E Fixing sub roller 56UA5307
032 1F Ozone filter 56UA1121
56UA1128
033 20 Ozone suction filter 56UA1122
56UA1129
034 21 Charging corona 56UA-250
035 22 PCL 56UA-257
036 23 Developing unit 56UA-300
037 24 Develop suction box 56UA-325
038 25 Trans/Sep unit 56UA-270
039 26 TSL 55VA8308
040 27 Regis. feed count 56UA7602
56UA4606
041 28 ADU accelerator roller 56UA4740 1 count for each reverse exit paper in the single
side mode, 0 count for each 1side straight
mode, 1 count in the double side mode.
042 29 Reversal output roller 56UA4741 2 count for each reverse exit paper in the single
side mode, 0 count for each 1side straight
mode, 1 count in the double side mode.
043 2A ADU reversal roller 56UA4741 2 count for each reverse exit paper in the single
side mode, 0 count for each 1side straight
mode, 2 count in the double side mode.
044 2B Output convey roller 56UA4742 1 count for each reverse exit paper in the single
56UA4743 side mode, 0 count for each 1side straight
mode, 0 count in the double side mode.
045 2C ADU convey roller 56UA4744 0 count for each paper exit in the single side
56UA4683 mode, 1 counts in the double side mode.
046 2D Fixing exit roller 56UA4595 1 count for each paper exit in the single side
(N = 4) mode, 2 counts in the double side mode.
047 2E Output roller 56UA4557
048 2F Fixing gear /2 56UA7783
049 30 Web Motor 56GA8017
050 31 Fixing output actuator 56UA5383
051 32 Toner pump /1 56UA-780
052 33 Toner pump /2 56UA-790
374 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
053 34 Tray 1 feed roller 55VA-464 1 count for each paper exit from tray /1.
054 35 Tray 1 conv/rev roller 55VA-463
055 36 Tray 1 feed clutch 56AA8201
056 37 Tray 1 handle clutch 56AA8201 1 count for each paper exit when the clutch is
turned ON by paper from tray /1.
057 38 Tray 2 feed roller 55VA-464 1 count for each paper exit from tray /2.
058 39 Tray 2 conv/rev roller 55VA-463
059 3A Tray 2 feed clutch 56AA8201
060 3B Tray 2 handle clutch 56AA8201 1 count for each paper exit when the clutch is
turned ON by paper from tray /2.
061 3C Tray 3 feed roller 55VA-484 1 count for each paper exit from tray /3.
062 3D Tray 3 conv/rev roller 55VA-483
063 3E Tray 3 feed clutch 56AA8201
064 3F Tray 3 handle clutch 56AA8201 1 count for each paper exit when the clutch is
065 40 Tray 3 reverse clutch 56AA8201 turned ON by paper from tray /3.
066 41 Tray 4 feed roller 55VA-484 1 count for each paper exit from tray /4.
067 42 Tray 4 conv/rev roller 55VA-483
068 43 Tray 4 feed clutch 56AA8201
069 44 Tray 4 handle clutch 56AA8201 1 count for each paper exit when the clutch is
070 45 Tray 4 reverse clutch 56AA8201 turned ON by paper from tray /4.
071 46 Tray 5 feed roller 55VA-484 1 count for each paper exit from tray /5.
072 47 Tray 5 conv/rev roller 55VA-483
073 48 Tray 5 feed clutch 56AA8201
074 49 Tray 5 handle clutch 56AA8201 1 count for each paper exit when the clutch is
075 4A Tray 5 reverse clutch 56AA8201 turned ON by paper from tray /5.
076 4B Paper fur brush 55VA-574 1 count for each paper exit.
077 4C V-convey exit roller 56UA4412
078 4D Paper powder scraper 56UA4419
079 4E V-convey clutch top 56AA8201 1 count for each paper exit from tray /1 and /2.
080 4F V-convey clutch mid. 56AA8201 1 count for each paper exit from tray /2.
081 50 V-convey clutch low 56AA8201
082 51 V-convey roller /1 56UA4413 1 count for each paper exit.
083 52 V-convey roller 2/3 56UA4414 1 count for each paper exit from tray /2.
56UA4464
084 53 Tray 1 pre-reg. roller 56UA4411 1 count for each paper exit from tray /1 and /2.
085 54 Tray 2 pre-reg. roller 56UA4411 1 count for each paper exit from tray /2.
086 55 PFU V-convey roller /T 15BA4507 1 count for each paper exit from tray /3.
15BA4508
087 56 PFU V-convey roller /M 15BA4507 1 count for each paper exit from tray /4.
088 57 PFU V-convey roller /L 15BA4507 1 count for each paper exit from tray /5.
15BA4508
375
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
089 58 PFU output roller 15BA5011 1 count for each paper exit from tray /3, /4 and
/5.
090 59 PFU V-convey clutch /T 56AA8201 1 count for each paper exit from tray /3.
091 5A PFU V-convey clutch /M 56AA8201 1 count for each paper exit from tray /4.
092 5B PFU V-convey clutch /L 56AA8201 1 count for each paper exit from tray /5.
093 5C PFU Mid-conv clutch /T 56AA8201 1 count for each paper exit from tray /3.
094 5D PFU Mid-conv clutch /L 56AA8201 1 count for each paper exit from tray /5.
095 5E Exposure On time 56UA8301 Accumulation of time lamp is on. 1 count per
second.
096 5F Fixing cleaning roller 56UA5353 1 count for each paper exit in the single side
097 60 Web prevention part 56UA-544 mode, 2 counts in the double side mode.
098 61 Main Switch 55GA8601 1 count each time the main power switch turns
OFF the power.
099 62 Door Switch 40AA8501 1 count each time the front door is opened
100 63 Tray 1 feed count 56UA-400 1 count for each paper exit from tray /1.
101 64 Tray 2 feed count 56UA-400 1 count for each paper exit from tray /2.
102 65 Tray 3 feed count 15BA-300 1 count for each paper exit from tray /3.
103 66 Tray 4 feed count 15BA-400 1 count for each paper exit from tray /4.
104 67 Tray 5 feed count 15BA-300 1 count for each paper exit from tray /5.
105 68 8k,16k Duplex count For the paper type which is between 270 mm
and 279 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
106 69 B4, B5 Duplex count For the paper type which is between 257 mm
and 270 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
107 6A 8.5 Duplex count For the paper type which is between 215 mm
and 257 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
108 6B A4S, A5 Duplex count For the paper type which is between 210 mm
and 215 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
109 6C 8, 8.125, 8.25 Dup.count For the paper type which is between 203 mm
and 210 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
110 6D B5R Duplex count For the paper type which is between 182 mm
and 203 mm width and 91 g/m2 or less, 0
count for each paper exit in the single side
mode, and 1 count for the double side mode.
376
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
111 6E FS Staple/Front 15AA4222 1 count for each paper exit in either of the 1-
staple at front or the 2-staple mode.
112 6F FS Staple/Back 15AA4222 1 count for each paper exit in either of the 1-
staple at rear or the 2-staple mode.
113 70 FS solenoid /A 56QA8251 1 count for each paper exit in the non-sort
mode and the sort mode.
114 71 FD feed roller /A Top 50BA-574 Counts the paper feed from PI tray /Up.
115 72 FD reverse rubber /Top 13QN-443
116 73 FD feed roller /B Top 50BA-575
117 74 FD feed roller /A Low 50BA-574 Counts the paper feed from PI tray /Lw.
118 75 FD reverse rubber /Low 13QN-443
119 76 FD feed roller /B Low 50BA-575
120 77 FD punch motor assy 15AG-573 1 count for each paper exit in the punch mode.
121 78 FD solenoid /A (release 1) 56QA8251 1 count for each paper exit in the punch or fold-
ing mode (all size).
122 79 FD solenoid /A (release 2) 56QA8251 • 1 count for each paper exit in the folding
mode (all size)
• 1 count for each paper exit in the punch
mode (paper length 220 mm or larger).
123 7A FD motor assy 129U-108 1 count for each paper exit to the main tray.
124 7B LS1 solenoid (Lead) 15AV8252 1 count for each paper exit in the non-sort and
125 7C LS1 solenoid (Rear) 15AV8253 sort mode (all size).
126 7D LS1 solenoid (Center) 15AV8251 1 count for each paper exit in the non-sort and
sort mode (Length 295 mm or more and Width
226 or more).
127 7E LS1 solenoid (Curl) 15AV8255 1 count for each paper exit in the non-sort
mode.
128 7F LS1 Up/Down motor 15AV8003 Counts operation number of times of the
stacker tray up down motor.
129 80 LS2 solenoid (Lead) 15AV8252 1 count for each paper exit in the non-sort and
130 81 LS2 solenoid (Rear) 15AV8253 sort mode (all size).
131 82 LS2 solenoid (Center) 15AV8251 1 count for each paper exit in the non-sort and
sort mode (Length 295 mm or more and Width
226 or more).
132 83 LS2 solenoid (Curl) 15AV8255 1 count for each paper exit in the non-sort
mode.
133 84 LS2 Up/Down motor 15AV8003 Counts operation number of times of the
stacker tray up down motor.
134 85 SD Staple/Right 15AN-550 1 count for each paper exit in the saddle stitch
135 86 SD Staple/Left 15AN-550 mode.
136 87 SD trimmer edge 15AN-570 1 count for each paper exit in the trimming
137 88 SD trimmer receiver 15AN5282 mode.
1 377
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
138 89 SD convey solenoid 15AN8251 1 count for each paper exit to the folding sec-
139 8A SD solenoid 13QE8251 tion.
140 8B SDFNS solenoid /2 12QR8252 1 count for each paper exit to the stacker.
141 8C ADF pick up roller 13GA4604 Original feed count in all modes.
142 8D ADF feed roller 15AS4605
143 8E ADF retard roller 13GA4606
144 8F ADF sub pick roller 13GA4601
145 90 ADF torque limiter 13GA-135
146 91 ADF SDF solenoid 13GA8252 Total original feed count in the single feed mode.
147 92 ADF LSB solenoid 13GA8251 • 1 count for each set of the large size original
single side mode.
• 1 count for each sheet of the large size orig-
inal double side mode. *1
148 93 ADF press/release SD 13GA8251 1 count for each sheet of the large size original
double side mode. *1
149 94 ADF SSB solenoid 13GA8251 1 count for each sheet of the small size original
double side mode.
150 95 Toner collect box 14RT-970 1 count for each paper exit in the single side
151 96 Recycling cut pump 14RT-210 mode, 2 counts in the double side mode.
152 97 Accumulator 14RT-230
153 98 Stirring plate assy 56UA-347 1 count for each paper exit in the single side
56UA-348 mode, 2 counts in the double side mode.
154 99 PB sub tray exit solenoid 15ANR714 1 count for each paper exit on the sub tray.
155 9A PB SC roller release 13GQ8005 1 count for each paper exit on the stacker.
motor
156 9B PB SC stopper solenoid 15AA8251
157 9C PB SC pressure arm sole- A07B746
noid
158 9D PB switchback roller 13GQ4519 1 count for each paper exit.
159 9E PB pick-up roller 55VA-464 1 count for each book exit in PB tray cover
160 9F PB paper feed roller sep- 55VA-463 mode.
aration roller
161 A0 PB paper pick up clutch 56AA8201
162 A1 PB cover paper separa- 56AA8201
tion clutch
163 A2 PB roller cutter blade assy A0756230 1 count for each book exit in cover trimming mode.
164 A3 PB filter /1 A0753724 1 count for each paper exit.
165 A4 PB filter /2 A0753734
166 A5 PB straight gate solenoid 56QA8251 1 count for each book exit except in PB tray
cover mode.
*1 The large size original represents all originals in the mixed original mode; A3, B4, A4S, B5S, 8K, 16KS, 11
x 17, 81/2 x 14, 81/2 x 11S, 8 x 13, 81/4 x 13, 81/8 x 13 and 81/2 x 13.
378 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Confirm and reset part name, part number, limit value
setting and print count. 2. "Service mode menu screen"
Up to 30 data from No.01 to No.30 can be set. Press the [03 Counter] key.
1 count is taken for each passage of paper, regard- 3. A sub menu appears on the right side of the
less of the paper size. screen.
Press the [03 Parts Counter] key on the sub
(1) Setting of each part and confirmation of the menu.
copy count 4. "Copy count of part menu screen"
1) Procedure Press the [02 Count of each parts] key.
5. "Copy count of each part screen"
1. Enter the service mode.
Press the [Next] or [Previous] key to scroll the
2. "Service mode menu screen"
screen.
Press the [03 Counter] key.
Press the [S] or [T] key to select an item you
3. A sub menu appears on the right side of the want to reset.
screen.
6. Press the [Count Reset] key.
Press the [03 Parts Counter] key on the sub
7. "Reset confirm screen"
menu.
Press the [Yes] key to reset the counter.
4. "Copy count of part menu screen"
Press the [No] key not to reset the counter. You
Press the [02 Count of each parts] key.
return to the "Copy count of each part screen."
5. "Copy count of each part screen"
Press the [Next] or [Previous] key to scroll the
screen. NOTE
Press the [S] or [T] key to select a data • When the copy count is in excess of a limit
number. value, an asterisk "*" is shown to the right of
6. Select either the [Name Setting], [P/N Setting] the limit value.
or [Limit Setting] key.
7. Press one of the key you want to set or
change, and enter it with the alphanumeric
keys.
• [Name Setting] : Enter a part name (8 digits)
• [P/N Setting] : Enter a part number (9 dig-
its)
• [Limit Setting] : Enter a limit value (8 digits)
8. Press the [OK] key to update data.
Press the [Cancel] key to cancel the update.
379
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
27 Z4:1A Z3:1A G0:1A H0:1A 3. A sub menu appears on the right side of the
screen.
28 Z4:1B Z3:1B G0:1B H0:1B
Press the [01 I/O Check Mode] key on the sub
29 Z4:1C Z3:1C G0:1C H0:1C
menu.
30 Z4:1D Z3:1D G0:1D H0:1D
4. "I/O check mode screen"
Enter the input check code with the numeric
keys.
5. To use the multi mode, press the Access but-
ton.
6. Enter the multi code with the numeric keys.
7. Input check result will appear in the message
display area.
8. Repeat steps 3 to 7 to perform the other signal
input check.
380
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
2. "Service mode menu screen" section")
Press the [04 Machine Condition] key. 2. Check the stamp letter [1] placed on the multi
3. A sub menu appears on the right side of the feed detection board /1, /2, and rotate the
screen. rotary switch [2] on the ADU drive board /1
Press the [01 I/O Check Mode] key on the sub (ADUDB1) as shown in the table below.
menu.
4. "I/O check mode screen" [1]
Enter the output check code with the numeric
keys.
5. To use the multi mode, press the Access but-
ton.
6. Enter the multi code with the numeric keys.
7. Press the Start button to perform the output
check. D
[2]
D. Adjustment when replacing the multi feed
detection board (main body)
When the multi feed detection board of the main
body or the ADU drive board /1 (ADUDB1) is
replaced, conduct this adjustment. And also adjust it
when multi feed is not detected properly due to spe-
cific types of paper (such as thin paper, coated paper
with less stiffness, and thick paper).
However, multi feed detection control is not applica-
ble to paper weight more than 210 g/m2 and coated
paper of 50 to 61 g/m2.
1050fs3056c
NOTE
• The multi feed detection board /1 and /2 are
Stamp letter Rotary switch
adjusted in the manufacturing process as a
A 0
pair of upper and lower. Be sure to replace
them as a pair. B 1
• Adjustment error may occur because of the C 2
temperature of the sensor surface. Make the D 3
adjustment at a temperature close to that in E 4
which the copier is actually used (20 to 30°C). F 5
(In case you brought a new part from out-
doors, make the adjustment after the temper- 3. Select the input check code "56-00" of the I/O
ature of the sensor surface and the room check mode in the service mode.
temperature become the same)
381
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
4. Insert one sheet of the paper (P/N 65AA-9910) 8. Insert one sheet of paper that customer mainly
between the multi feed detection board /1 and use (paper weight 62 to 209 g/m2), and confirm
2
/2 (200 to 300 g/m paper can also be used). that "L" appears on the input check display.
/1050e/1050eP
Be sure the paper does not trail down. "L": no multi feed (0 or 1 sheet of paper)
"H": multi feed (2 sheets of paper)
Note
• If the paper trails down, the angle of paper Note
insertion is different from that of paper pas- • When "H" is once detected, the guide plate
sage, thus making it impossible to make an to which the multi feed detection board /2
accurate adjustment. is installed must be opened and closed.
5. Connect the tester (voltmeter) to the following Otherwise, a return to "L" is not available.
positions of the ADUDB1. 9. Insert another sheet of paper (2 sheets in all),
+terminal: test pin No. TP60 (white) [1] that customer mainly use and confirm that "H"
- terminal: test pin No. TP57 (green) [2] appears on the input check display.
Range: DC 20 V 10. In case of detection error, return to step 4 to
conduct the adjustment again. In step 6, set
power voltage to the value 1.0 V lower than the
previous adjustment.
11. Repeat the steps 8 to 10 until detection error is
resolved.
12. Pull out the inserted papers, and install the
parts you removed.
382 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• If the front door /Rt is not open, the blade
motor (M22) does not rotate.
H. Adjustment when replacing the multi feed
5. Press the Start button.
detection board (PI)
6. The blade motor (M22) starts rotating, and the Adjust when replacing the multi feed detection board
cleaning blade moves from the drum to the
of the PI section or the PI drive board (PIDB). Also,
transportation lock position. perform this adjustment when multi feed of special
paper (thin paper, coated paper with less stiffness,
F. Scanner transportation lock thick paper) cannot be detected properly.
Move the scanner mirror to the transportation lock
position, thus making it easy to fix the mirror with NOTE
screws. • The multi feed detection board /1 and /2 are
Use this when packing the machine while moving an adjusted in the manufacturing process as a
installation location. pair of upper and lower. Be sure to replace
them as a pair.
(1) Procedure • Adjustment error may occur because of the
temperature of the sensor surface. Make the
1. Enter the I/O check mode. adjustment at a temperature close to that in
2. Enter "36" with the numeric keys. Confirm that which the copier is actually used (20 to 30°C).
"36-00" is displayed in the message display (In case you brought a new part from out-
area. doors, make the adjustment after the temper-
3. Press the Start button. ature of the sensor surface and the room
temperature become the same)
4. The scanner motor (M27) starts rotating, and
the mirror moves to the left.
(1) Procedure
5. Fix the mirror with the lock screws of the scan-
ner mirror you removed when unpacking the 1. Replace the multi feed detection board /1, /2.
machine. (See "3.3.17 Removing/reinstalling the multi
feed detection boards /1 (MFDB/1) and /2
(MFDB/2)") in Field Service for FD-501)
G. Removing toner in the toner mixing section
After moving the installation location of the machine,
remove toner which may have dropped into the mix-
ing section of the toner supply section.
(1) Procedure
383
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
2. Check the stamp letter [1] placed on the multi 4. Open the FD upper door and front door to turn
feed detection board /1, /2, and rotate the the jam clearing knob [1]. Insert one sheet of
rotary switch [2] on the PI drive board (PIDB) as paper [2] (P/N 65AA-9910) between the multi
/1050e/1050eP
per following table. feed detection board /1 and /2 [3] (200 to 300
g/m2 paper can also be used).
Note
• Turn the jam clearing knob until the paper
hits the roller [4], thus confirming that the
paper is between the multi feed detection
board /1 and /2.
[2]
[1]
Note
• The rotary switch 5 is not used.
3. Select the output check code "70-82" of the I/
O check mode in the service mode.
384
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
+ terminal: test pin No. TP51 (GAIN) [1]
I. Adjustment when replacing the multi feed
- terminal: test pin No. TP11 (SGND) [2]
detection board (PB)
Range: DC 20 V
Adjust when replacing the multi feed detection board
of the PB or the PB control board (PBCB). Also, per-
VR2
form this adjustment when multi feed of special paper
(thin paper, coated paper with less stiffness, thick
paper) cannot be detected properly.
NOTE
• The multi feed detection board /1 and /2 are
adjusted in the manufacturing process as a
pair of upper and lower. Be sure to replace
them as a pair.
• Adjustment error may occur because of the
temperature of the sensor surface. Make the
adjustment at a temperature close to that in
which the copier is actually used (20 to 30°C).
LED1 (In case you brought a new part from out-
[1] [2] fd501fs3007c
doors, make the adjustment after the temper-
ature of the sensor surface and the room
Note temperature become the same)
• Because the FD is powered, do not drop
any metal material on the board, or do not (1) Procedure
connect the tester pin to an irrelevant ter-
1. Replace the multi feed detection board /1, /2.
minal.
(See ”3.2.24 Removing/reinstalling the multi
It may cause the board to short circuit and
feed detection board /1 (MFDTB71) and /2
be damaged.
(MFDTB72)” in Field Service for FB-501)
6. In the PIDB volume (VR2), set power voltage to
the standard value.
Standard value: 8.0 ± 0.2 V
7. Pull out the paper inserted in step 4.
8. Insert one sheet of paper that customer mainly
use (paper weight 50 to 300 g/m2), and confirm
that the PIDB's LED (LED1) can be turned on.
LED on: no multi feed (0 or 1 sheet of paper)
LED off: multi feed (2 sheets of paper)
9. Insert another sheet of paper (2 sheets in all),
that customer mainly use, and to see if the LED
is turned off.
10. In case of detection error, return to step 4 to
conduct the adjustment again. In step 6, set
power voltage to the value 1.0 V lower than the
previous adjustment.
11. Repeat steps 7 to 10 until detection error is
resolved.
385
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
2. Check the stamp letter [1] placed on the multi 8. Press the Start button.
feed detection board /1, /2, and rotate the The paper is fed from the PB cover paper tray
rotary switch [2] on the PBCB as per following and stops at the conveyance section.
/1050e/1050eP
table. Note
• Confirm that the paper is between the multi
feed detection board /1 and /2.
9. After the operation, press the Stop button.
10. Connect the tester (voltmeter) to the following
positions of the PBCB.
+ terminal: test pin No. TP28 (GAIN) [1]
- terminal: test pin No. TP24 (SGND) [2]
Range: DC 20 V
[1]
[1]
[2]
564Af3c001cb
Note
• Because the PB is powered, do not drop
Stamp letter Rotary switch any metal material on the board, or do not
A 1 connect the tester pin to an irrelevant ter-
minal.
B 2
It may cause the board to short circuit and
C 3
be damaged.
D 4
11. In the PBCB volume (VR4), set power voltage
E 5
to the standard value.
Standard value: 8.0 ± 0.1 V
3. Insert one sheet of paper (P/N 65AA-9910, fus-
12. Pull out the paper inserted in step 8.
ing adjustment paper, 16 sheets/A3) in the
cover paper tray of the PB (200 to 300 g/m2 13. Insert one sheet of paper that customer mainly
paper can also be used). use (paper weight 50 to 300 g/m2), and confirm
that the PBCB's LED (LED1) can be turned on.
4. Select the output check code "75-96" of the I/
LED on: no multi feed (0 or 1 sheet of paper)
O check mode in the service mode.
LED off: multi feed (2 sheets of paper)
5. Press the Start button to perform the all initializing operation.
14. Insert another sheet of paper (2 sheets in all),
6. After the operations, press the Stop button.
that customer mainly use, and to see if the LED
7. Select the output check code "75-95" of the I/
is turned off.
O check mode in the service mode.
385-1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
previous adjustment. ten.
NOTE
• Only one type of data can be backed up.
When backed up again, data will be overwrit-
ten.
• When the main body is connected to two or
more option, data is backed up to all
EEPROMs. If you want to back up data to
specific option, connect specific option to the
main body.
(1) Procedure
1 385-2
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
NOTE
• The operation can not be cancelled during the
HDD1 bad sectors check and recovery (the STOP
button or the [Return] key are disabled).
386
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
tion code H L
Analog PS31 01 01 Toner remaining sensor /1 No toner Toner
signal
PS32 02 Toner remaining sensor /2
PS33 03 Toner remaining sensor /3
PS34 04 Toner remaining sensor /4
TH5 02 00 Drum temperature sensor 0 to 255
TH1 03 00 Thermistor /1
TH3 04 00 Thermistor /3
TCSB 05 00 Humidity sensor signal
06 00 Max. density sensor monitor signal
07 00 Max. density sensor output signal
08 00 Gamma sensor output signal
DPSB 09 00 Drum potential sensor output signal
TCSB 10 00 Drum jam sensor output signal Paper No paper
Paper PS8 11 01 Paper empty sensor /1 (Tray /1)
feed PS14 02 Paper empty sensor /2 (Tray /2)
PS73 03 Paper empty sensor /1 (Tray /3)
PS79 04 Paper empty sensor /2 (Tray /4)
PS85 05 Paper empty sensor /3 (Tray /5)
VR1 12 01 Remaining paper VR /1 (Tray /1) 0 (FULL) to 4 (EMPTY)
VR2 02 Remaining paper VR /2 (Tray /2)
VR10 03 Remaining paper VR /1 (Tray /3)
VR12 04 Remaining paper VR /2 (Tray /4)
VR14 05 Remaining paper VR /3 (Tray /5)
PS4 13 01 Paper size sensor /Fr1 (Tray /1) ON OFF
PS5 02 Paper size sensor /Rr1 (Tray /1)
PS10 03 Paper size sensor /Fr2 (Tray /2)
PS11 04 Paper size sensor /Rr2 (Tray /2)
PS75 05 Paper size sensor /Fr1 (Tray /3)
PS76 06 Paper size sensor /Rr1 (Tray /3)
PS81 07 Paper size sensor /Fr2 (Tray /4)
PS82 08 Paper size sensor /Rr2 (Tray /4)
PS87 09 Paper size sensor /Fr3 (Tray /5)
PS88 10 Paper size sensor /Rr3 (Tray /5)
VR2 14 01 Paper size VR /1 (Tray /1) 0 to 255
VR4 02 Paper size VR /2 (Tray /2)
VR11 03 Paper size VR /1 (Tray /3)
VR13 04 Paper size VR /2 (Tray /4)
VR15 05 Paper size VR /3 (Tray /5)
1 387
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
388
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
conveyance PS16 02 Loop sensor
PS40 03 Registration sensor
PS92 04 Loop sensor /1 (Tray /3)
PS94 05 Loop sensor /2 (Tray /4)
PS98 06 Loop sensor /3 (Tray /5)
PS99 07 PFU exit sensor
PS22 24 01 Fusing exit sensor
PS3 02 Paper exit sensor
PS48 03 Reverse sensor /1
PS47 04 Reverse sensor /2
PS23 05 Fusing jam sensor
PS50 06 ADU reverse paper exit sensor
SW4 25 01 Door switch /1 Open Close
PS2 02 Door open/close sensor /2
PS1 03 Door open/close sensor /1
MS1/2 04 Interlock switch /1, /2
PS317 05 APS timing sensor
SW5 06 Door switch /2
— 07 Fusing section set detection signal Set Not set
— 08 Sensitive drum section set detection signal
PS70 09 Door open/close sensor (PF) Open Close
SW11 10 Vertical conveyance door switch /Up (PF) ON OFF
SW12 11 Vertical conveyance door switch /Lw (PF)
SW10 12 Door switch (PF) Open Close
SW13 13 Horizontal conveyance door switch (PF) ON OFF
Scanner PS51 30 01 Scanner home sensor Home Other than
position home position
PS52 31 01 APS sensor /1 No original Original
PS53 02 APS sensor /2
PS317 08 APS timing sensor Open Close
Peculiar CNT2 52 00 Key counter Connected Unconnected
functions PS37 53 00 Transfer assist home sensor Home Other than
PS26 54 01 Charger cleaning home sensor position home position
PS27 02 Charger cleaning limit sensor Limit Other than
position limit position
PS38 03 Transfer/separation home sensor Home Other than
position home position
PS39 04 Transfer/separation limit sensor Limit Other than
position limit position
PS24 55 01 Blade sensor /1 ON OFF
PS25 02 Blade sensor /2
389
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
390
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
DCPS 21 24 V output Normal Abnormal
PS2 22 Folding exit sensor Paper No paper
CN90 23 Main tray connection recognition (CN90 Unconnected Connected
connection)
PS51 24 1st folding conveyance sensor No paper Paper
PS52 25 Folding entrance sensor
PS53 26 2nd folding conveyance sensor
PS54 27 3rd folding conveyance sensor
PS55 28 1st folding cam home sensor Pressure Non-pressure
PS56 29 2nd folding cam home sensor
PS57 30 3rd folding cam home sensor
PS58 31 S size conveyance sensor Paper No paper
PS6 32 Punch registration sensor
FDOB 33 Staple selection switch OFF ON
FDOB 34 Punch selection switch
FDOB 35 Folding selection switch
FDOB 36 Start/Stop switch
FDOB 37 Multi feed function select switch
PS46 39 Sub tray paper full sensor Full Other than full
PS31 40 PI conveyance sensor /Up Paper No paper
PS37 41 PI conveyance sensor /Lw
PS32 42 PI upper limit sensor /Up Upper limit Other than
upper limit
PS33 43 PI paper empty sensor /Up Other than full Full
PS34 44 PI lift plate home sensor /Up Home Other than
position home position
PS35 45 L size sensor /Up No paper Paper
PS36 46 S size sensor /Up
— 47 — — —
PS38 48 PI upper limit sensor /Lw Upper limit Other than
upper limit
PS39 49 PI paper empty sensor /Lw Other than full Full
PS40 50 PI lift plate home sensor /Lw Home Other than
position home position
PS41 51 L size sensor /Lw No paper Paper
PS42 52 S size sensor /Lw
PS43 53 PI cover open/close sensor Close Open
PS44 54 PI paper set sensor /Up No paper Paper
PS45 55 PI paper set sensor /Lw
— 56 — — —
— 57 —
1 391
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
— 59 —
— 60 —
PS47 61 PI max paper size sensor /Up No paper Paper
PS48 62 PI max paper size sensor /Lw
SD PS1 71 01 Entrance sensor Paper No paper
PS2 02 Horizontal conveyance sensor /1
PS3 03 Horizontal conveyance sensor /2
PS4 04 Horizontal conveyance exit sensor
PS5 05 Right angle conveyance sensor /1 No paper Paper
PS6 06 Right angle conveyance sensor /2
PS7 07 Folding sensor /1
PS8 08 Folding passage sensor Paper No paper
PS17 09 Overlap home sensor Home Other than
position home position
PS18 10 Folding main scan alignment home sensor /Fr1 Other than Home
PS49 11 Folding main scan alignment home sensor /Fr2 home position position
PS20 12 1st folding blade home sensor /1
PS21 13 1st folding blade home sensor /2 Home Other than
position home position
PS22 14 2nd folding blade home sensor /1 Other than Home
home position position
PS23 15 2nd folding blade home sensor /2 Home Other than
PS24 16 Folding exit home sensor position home position
PS9 17 Tri-folding exit sensor Paper No paper
PS10 18 Tri-folding paper full sensor Other than full Full
PS11 19 Subtray exit sensor Paper No paper
PS12 20 Subtray paper full sensor Other than full Full
PS44 21 Folding sensor /2 No paper Paper
PS19 22 Folding main scan alignment home sensor /Rr Home Other than
PS46 23 Guide shaft home sensor position home position
HS2/HS4 24 Clincher start sensors /Rt and /Lt No clinch Clinch
— 25 — — —
— 26 —
— 27 —
— 28 —
— 29 —
— 30 —
— 31 —
— 32 —
PS13 33 Saddle stitching paper sensor No paper Paper
PS14 34 Bundle sensor /1
392 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
PS16 36 Bundle registration plate home sensor Other than Home
home position position
PS25 37 Stapler movement home sensor Home Other than
position home position
PS26 38 Clincher up down home sensor Other than Home
home position position
PS27 39 Saddle stitching press home sensor Home Other than
PS28 40 Saddle stitching alignment home sensor /Rt position home position
PS29 41 Saddle stitching alignment home sensor /Lt
PS33 42 Bundle clip upper limit sensor Upper limit Other than
upper limit
PS30 43 Bundle clip lower limit sensor Lower limit Other than
lower limit
PS32 44 Bundle arm home sensor Home Other than
PS31 45 Bundle arm rotation home sensor position home position
PS34 46 Bundle registration home sensor
PS35 47 Bundle press stage up down home sensor
PS45 48 Bundle press stage up down limit sensor Upper limit Other than
upper limit
PS37 49 Bundle press home sensor Other than Home
home position position
PS47 50 Bundle press lower limit sensor Other than Lower limit
lower limit
PS48 51 Scraps press home sensor Other than Home
home position position
PS40 52 Scraps box set sensor Set Not set
PS41 53 Trimmer scraps full sensor Other than full Full
PS36 54 Bundle press movement home sensor Home Other than
PS38 55 Bundle arm assist home sensor position home position
PS39 56 Bundle arm assist upper limit sensor Upper limit Other than
upper limit
SW1 57 Staple empty switch /Rt No staple Staple
SW2 58 Staple empty switch /Lt
HS1 59 Stapler home sensor /Rt Other than Home
HS3 60 Stapler home sensor /Lt home position position
— 61 — — —
— 62 —
— 63 —
— 64 —
PS42 65 Front door sensor /Rt Open Close
PS43 66 Front door sensor /Lt
1 393
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
394 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
PS47 21 Staple ready sensor /Fr Other than Ready
ready
PS43 22 Cartridge set sensor /Fr No cartridge Cartridge
PS45 23 Staple empty sensor /Fr No staple Staple
PS41 24 Stapler home sensor /Fr Other than Home
home position position
PS46 25 Staple ready sensor /Rr Other than Ready
ready
PS42 26 Cartridge set sensor /Rr No cartridge Cartridge
PS44 27 Staple empty sensor /Rr No staple Staple
PS40 28 Stapler home sensor /Rr Other than Home
home position position
— 29 — — —
PS20 30 Stacker empty sensor No paper Paper
PS9 31 Paper exit arm home sensor Home Other than
position home position
MS1 32 Door switch Open Close
PS31 33 Alignment home sensor /Fr Home Other than
PS8 34 Alignment home sensor /Rr position home position
LS PS4 73 01 Entrance sensor Paper No paper
tandem PS11 02 Sub tray paper exit sensor
(1st) PS7 03 Conveyance sensor /1
PS16 04 Conveyance sensor /2 (LS-501 only)
PS17 05 Conveyance sensor /3 (LS-501 only)
PS18 06 Tandem exit sensor (LS-501 only)
PS3 07 Stacker tray upper limit sensor Upper limit Other than
upper limit
PS6 08 Paper empty sensor Full Other than full
PS13 09 2,000 sheets stacked sensor ON OFF
— 10 — — —
PS14 11 5,000 sheets stacked sensor ON OFF
PS9 12 Sub tray full sensor Full Other than full
PS1 13 Stacker tray set sensor Set Not set
RS1 14 Hand cart reset switch
PS15 15 Stacker tray arm release sensor ON OFF
TOB 16 Paper exit switch
MS1 17 Door switch Open Close
RS2 18 JAM door switch
PS8 19 Sub tray door sensor
1 395
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
396 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
sensor
PS13 09 SC switchback spring pressure detection sen- ON OFF
sor
PS14 10 SC alignment HP sensor Home Other than
position home position
PS16 11 SC paper detection sensor No paper Paper
PS17 12 SC roller release sensor Press the Release the
roller roller
PS18 13 Clamp entrance movement HP sensor Home Other than
position home position
PS19 14 Clamp entrance roller release sensor Press the Release the
roller roller
PS21 15 Clamp alignment HP sensor Home Other than
PS22 16 Clamp HP sensor position home position
PS23 17 Clamp pressure sensor ON OFF
PS24 18 Clamp rotation HP sensor Home Other than
position home position
PS25 19 Clamp rotation pressure sensor Pressurize Not pressur-
ize
PS26 20 Cover paper table upper limit sensor /Fr Upper limit Not at upper
PS27 21 Cover paper table upper limit sensor /Rr limit
PS28 22 Clamp paper sensor No paper Paper
PS29 23 Book thickness sensor Detection No detection
PS31 24 Glue tank movement limit sensor Upper limit is Not reached
reached
PS32 25 Glue apply position detection sensor No paper Paper
PS33 26 Glue tank HP sensor Home Other than
position home position
PS36 27 Pellet remain sensor No Pellet Pellet
PS37 28 Pellet count sensor No detection Detection
PS38 29 Pellet supply arm upper limit sensor Upper limit Not at upper
limit
PS39 30 Pellet supply arm lower limit sensor Lower limit Not at lower
limit
M32 31 Glue apply roller motor Normal Abnormal
PS3 32 Paper exit sensor No paper Paper
PS41 33 Cover paper alignment HP sensor Home Other than
PS42 34 Cover paper conveyance arm HP sensor position home position
/Rt
PS43 35 Cover paper conveyance arm HP sensor
/Lt
PS44 36 Cover paper switchback sensor No paper Paper
2 397
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
398 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
limit
PS75 69 Cover paper conveyance sensor /1 No paper Paper
PS76 70 Cover paper conveyance sensor /2
PS77 71 Cover paper conveyance sensor /3
PS78 72 Cover paper conveyance sensor /4
PS79 73 Cover paper conveyance sensor /5
PS80 74 Waste box full sensor Other than full Full
PS81 75 Waste box set sensor Set Not set
M71 76 Cover paper tray fan /1 Abnormal Normal
M72 77 Cover paper tray fan /2
M74 78 Cover paper feed motor Abnormal Normal
M80 79 Exhaust fan /1
PS82 80 Cover paper tray knob sensor Locked Unlocked
TH2 81 Glue tank temperature sensor /up 0 to 255
TH3 82 Glue tank temperature sensor /Md 0 to 255
TH4 83 Glue tank temperature sensor /Md 0 to 255
TH1 84 Glue apply roller temperature sensor 0 to 255
OB/1 85 Manual operation board Glue apply Glue apply
SW OFF SW ON
OB/1 86 Manual operation board Alignment Alignment
SW OFF SW ON
OB/1 87 Manual operation board Start SW Start SW
OFF ON
MS1 88 Pellet supply door switch Close Open
TH1 89 Glue apply roller temperature sensor Abnormal Normal
(overheat abnormality)
TH1 90 Glue apply roller temperature sensor
(low-temperature abnormality)
TH2 91 Glue tank temperature sensor /up
(overheat abnormality)
TH2 92 Glue tank temperature sensor /up
(low-temperature abnormality)
TH3 93 Glue tank temperature sensor /Md
(overheat abnormality)
94 Glue tank temperature sensor /Md
(low-temperature abnormality)
TH 95 Glue tank temperature sensor /Lw
(overheat abnormality)
96 Glue tank temperature sensor /Lw
(low-temperature abnormality)
ADU PS35 80 01 ADU conveyance sensor /1 Paper No paper
PS43 02 ADU exit sensor
2 399
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
400
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
Note
1050e/1050eP
• Do not output codes which are not described in the output check list.
401
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
402
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
feed 02 Conveyance motor (425 mm/s)
03 Conveyance motor (490 mm/s)
M18 26 01 Loop motor (1000 mm/s)
02 Loop motor (825 mm/s)
03 Loop motor (520 mm/s)
04 Loop motor (490 mm/s)
05 Loop motor (425 mm/s)
06 Loop motor (290 mm/s)
M9 27 01 Paper exit motor /1 (290 mm/s)
02 Paper exit motor /1 (425 mm/s)
03 Paper exit motor /1 (490 mm/s)
04 Paper exit motor /1 (520 mm/s)
05 Paper exit motor /1 (825 mm/s)
06 Paper exit motor /1 (1000 mm/s)
M13 10 Reverse paper exit motor (1000 mm/s)
11 Reverse paper exit motor (825 mm/s)
12 Reverse paper exit motor (520 mm/s)
M4 28 01 Paper feed motor
M40 02 Paper feed motor (PF)
SD5 29 00 Drum claw solenoid
M41 30 01 PF exit conveyance motor (290 mm/s)
02 PF exit conveyance motor (1000 mm/s)
03 PF exit conveyance motor (490 mm/s)
04 PF exit conveyance motor (425 mm/s)
Scanner M27 31 00 Home search + Scan
M21, 32 00 Polygon motor (low speed) + Polygon
FM18 cooling fan
01 Polygon motor (middle speed) + Polygon
cooling fan
02 Polygon motor (high speed) + Polygon
cooling fan
M27,L1 34 00 Shading correction
M27, 35 00 DF scan position move + Scanner cooling
FM19 fan
M27 36 00 Scanner packing lock move Used in re-packing
— 37 — —
LDB, M21 38 00 LD current value measurement (LD alarm level) Can be confirmed with list output
403
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
404
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
body CNT2 02 Key counter
PS54 03 Centering sensor LED
M19 44 01 Transfer assist motor Perform with ADU pulled
out to prevent drum dam-
age
M24 45 06 Web motor
Peculiar M23 46 00 Charger cleaning motor (shuttle)
functions 01 Charger cleaning motor (to the back)
02 Charger cleaning motor (to the front)
M20 47 00 Transfer/separation cleaning motor (shut-
tle)
01 Transfer/separation cleaning motor (to the
back)
02 Transfer/separation cleaning motor (to the
front)
OB2 48 00 Illuminate all LEDs
M20, 49 00 Charger cleaning + Transfer/separation
M23 cleaning (shuttle)
M3,M2 50 00 Developing motor + Drum motor
EL 51 00 Erase lamp
TSL 52 00 Transfer exposure lamp
— 53 01 Status indicator lamp — PAT1 ON
02 Status indicator lamp — PAT2 ON
03 Status indicator lamp — PAT3 ON
04 Status indicator lamp — PAT4 ON
M11 54 00 Intermediate hopper motor
M7 03 Toner hopper motor
M28 04 Toner pump motor (high speed)
05 Toner pump motor (low speed)
M29 06 Air pump motor (high speed)
07 Air pump motor (low speed)
M28, 08 Toner pump motor (high speed) +
M29 Air pump motor (high speed)
09 Toner pump motor (low speed) + Used after moving the
Air pump motor (low speed) machine
M10 10 Air separation motor
LCDB 55 00 Message test
M30 56 00 Recycle cut motor PCS part
— 57 — —
58 — —
59 — —
405
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
406 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
position move)
M15 30 2nd folding release motor (folding position
move)
M16 31 3rd folding release motor (conveyance
position move)
M16 32 3rd folding release motor (folding position
move)
SD1 61 Entrance gate solenoid
SD3 62 S size gate solenoid
SD4 63 L size gate solenoid
SD5 64 Roller solenoid /1
SD6 65 Roller solenoid /2
SD7 66 Roller solenoid /3
SD8 67 Roller solenoid /4
SD9 68 Sub tray gate solenoid
SD12 69 Paper exit solenoid
SD13 70 PI pick-up solenoid /Up
SD14 71 PI pick-up solenoid /Lw
SD15 72 Folding gate solenoid
— 73 —
SD18 74 2nd folding roller solenoid
CL1 75 PI registration clutch /Up
CL2 76 PI registration clutch /Lw
— 81 —
MFDB1 82 Multi feed detection board /1 (CLK output)
FDOB 89 FD operation board (lit all LEDs)
JAMIB 90 Jam indicator board (lit all LEDs)
— 99 —
SD M1 71 01 Entrance conveyance motor
M2 02 Horizontal conveyance motor
M3 03 Folding entrance motor
M4 04 Folding conveyance motor
M4 05 Folding conveyance motor
M6 06 Right angle conveyance motor
M29 07 Stapler motor /Rt (stapling)
M30 08 Stapler motor /Lt (stapling)
M5 09 Bundle exit motor
M8 10 Folding sub scan alignment exit motor
M5 21 Bundle exit motor (home search)
M7 24 Folding main scan alignment motor /Fr
(home search)
1 407
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(alignment)
M8 27 Folding sub scan alignment exit motor
(home search)
M9 29 Saddle stitching alignment motor /Rt
(home search)
M9 30 Saddle stitching alignment motor /Rt
(inward movement)
M10 31 Bundle arm motor (home search)
M10 32 Bundle arm motor (inward movement)
M11 33 Bundle clip motor (home search)
M12 34 Bundle registration motor (home search)
M13 35 Overlap motor (home search)
M14 36 Folding main scan alignment motor /Rr
(home search)
M14 37 Folding main scan alignment motor /Rr
(forward movement)
M15 39 Stapler movement motor (home search)
M15 40 Stapler movement motor
M16 41 Saddle stitching alignment motor /Lt
(home search)
M16 42 Saddle stitching alignment motor /Lt
(inward movement)
M17 43 Bundle press movement motor (home
search)
M18 44 1st folding blade motor (home search)
M19 45 2nd folding blade motor (home search)
M20 46 Clincher up down motor (home search)
M20 47 Clincher up down motor (stapling)
M21 48 Saddle stitching press motor (home search)
M22 49 Bundle arm rotation motor (home search)
M23 50 Bundle press motor (home search)
M24 51 Bundle press stage up down motor
(home search)
M25 52 Guide shaft motor (home search)
M31 53 Trimmer blade motor (home search)
M31 54 Trimmer blade motor (trimming position) Available after 71-53
(home search)
M32 55 Trimmer press motor (home search)
M32 56 Trimmer press motor (upper limit search)
M32 57 Trimmer press motor (pressing) Available after 71-55
(home search)
408 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
mer board release position) (home search)
M10 59 Bundle arm motor (inward movement)
M23 60 Bundle press motor (pressing)
M24 61 Bundle press stage up down motor (up)
M24 62 Bundle press stage up down motor (home
search for the bundle registration plate)
M26 63 Bundle arm assist motor (home search)
SD1 71 Entrance gate solenoid
SD2 72 Right angle conveyance gate solenoid
SD3 73 Horizontal conveyance gate solenoid
SD4 74 Roller release solenoid /4
SD5 75 Roller release solenoid /1 (roller press)
SD5 76 Roller release solenoid /1 (roller release)
SD6 77 Roller release solenoid /2
SD7 78 Roller release solenoid /3 (roller press)
SD7 79 Roller release solenoid /3 (roller release)
SD8 80 Folding unit lock solenoid (lock)
SD8 81 Folding unit lock solenoid (release)
SD11 82 Trimmer board solenoid (ON once)
SD11 83 Trimmer board solenoid (ON twice)
CL1 86 Tri-folding exit clutch
FM1 87 Scraps removal fan motor
— 95 Trimmer board solenoid operation Reset after replace the
counter reset trimmer board.
FS M1 72 01 Conveyance motor (1000 mm/sec)
M3 06 Tray up down motor (home search)
07 Tray up down motor (lower limit move)
08 Tray up down motor (staple mode up down)
M22 11 Alignment motor /Fr (home search)
12 Alignment motor /Fr (A4S standby posi-
tion move)
Note: effective after 72-11 home search
13 Alignment motor /Fr (A4S position move)
Note: effective after 72-12 A4S standby
position move
14 Alignment motor /Fr (A4S standby posi-
tion move)
Note: effective after 72-13 A4S position move
M7 16 Main tray paper exit motor (800 mm/sec)
17 Main tray paper exit motor (205 mm/sec)
M8 21 Paper exit opening motor (home search)
1 409
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
approx. 55°)
23 Paper exit opening motor (half opening:
approx. 44°)
24 Paper exit opening motor (small opening:
approx. 27°)
M31 26 Stapler motor /Fr (needles out, empty staple)
27 Stapler motor /Fr (staple)
M30 28 Stapler motor /Rr (needles out, empty staple)
29 Stapler motor /Rr (staple)
M11 31 Stapler movement motor (home search)
32 Stapler movement motor (A4 1 staple
position move)
M13 36 Stacker entrance motor (1000 mm/sec)
M26 41 Rear stopper motor (home search)
42 Rear stopper motor (stopper release)
SD5 46 Bypass solenoid
SD2 47 Gate solenoid
SD9 48 Paper exit opening solenoid (ON/OFF)
SD7 49 Intermediate roller release solenoid
M24 51 Stacker assist motor (home search)
M24 52 Stacker assist motor (assist position move)
M25 56 Intermediate roller open/close motor
(home search)
57 Intermediate roller open/close motor
(reserve position move)
M23 61 Paper exit arm motor (home search)
62 Paper exit arm motor (800 mm/sec)
63 Paper exit arm motor (400mm/sec)
M6 66 Sub tray paper exit motor (1000 mm/sec)
M5 71 Alignment motor /Rr (home search)
72 Alignment motor /Rr (A4S standby posi-
tion move)
Note: effective after 72-71 home search
73 Alignment motor /Rr (A4S position move)
Note: effective after 72-72 A4S standby
position move
74 Alignment motor /Rr (A4S standby posi-
tion move)
Note: effective after 72-73 A4S position move
M2 76 Paddle motor (ON/OFF)
M5, 78 Alignment motor /Rr, /Fr (home search)
M22
410
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
M22 position move)
Note: effective after 72-78 home search
80 Alignment motor /Rr, Fr (A4 position move)
Note: effective after 72-79 A4 standby
position move
JAMIB 90 Jam indicator board (illuminate all LEDs)
— 99 No paper running mode
20 sheets of A3 with 2 staples
LS M2 73 01 Conveyance motor (490 mm/s)
tandem 02 Conveyance motor (1000 mm/s)
(1st) M3 03 Sub tray paper exit motor (490 mm/s)
04 Sub tray paper exit motor (1000 mm/s)
M6 05 Tandem conveyance motor (490 mm/s)
06 Tandem conveyance motor (1000 mm/s)
M4 07 Grip conveyance motor (490 mm/s)
08 Grip conveyance motor (1300 mm/s)
M7 09 Alignment motor (initial operation)
10 Alignment motor
M5 11 Shift unit motor (home search)
12 Shift unit motor
M1 13 Stacker tray up down motor (down)
14 Stacker tray up down motor (up)
SD1 15 1st gate solenoid
SD10 16 2nd gate solenoid (LS-501 only)
SD9 17 Front stopper solenoid
SD3 18 Rear stopper solenoid
SD8 19 Paper press solenoid /3
SD6 20 Paper press solenoid /1
SD4 21 Front door lock solenoid
SD5 22 Entrance conveyance lock solenoid
SD11 Tandem conveyance lock solenoid
SD2 23 Job partition solenoid
SD7 24 Paper press solenoid /2
FM1, FM3, 25 Paper cooling fan /Fr, /Mi
FM2, FM6 Paper cooling fan motor /1, /2
FM5 26 Paper cooling fan /Rr
411
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
412 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(home position search)
11 SC switchback release motor
(High pressing position move)
12 SC switchback release motor
(Low pressing position move)
M15 13 SC alignment motor (home position
search)
14 SC alignment motor (A4 standby position 75-13 must have been
move) performed in advance.
15 SC alignment motor (alignment)
M17 16 SC bundle conveynace motor
M18 17 SC roller release motor
(home position search)
18 SC roller release motor
(movement to the pressing position)
M19 19 Clamp entrance movement motor (home
position search)
20 Clamp entrance movement motor(move- The following adjustments must
ment to the entrance position) have been made in advance.
1. 75-96
2. 75-31
3. 75-32
4. 75-19
5. 75-29
M20 21 Clamp entranse roller release motor
(home position search)
22 Clamp entranse roller release motor
(pressing position move)
SD11 23 FD alignment solenoid
SD12 24 SC stopper solenoid
SD13 25 SC pressure arm solenoid
M21 26 Clamp alignment motor (home position
search)
27 Clamp alignment motor (A4 standby posi-
tion move)
28 Clamp alignment motor (alignment)
M22 29 Clamp motor (home position search)
30 Clamp motor (movement to the clamp
position)
M23 31 Clamp rotation motor (home position 75-19 must have been
search) performed in advance.
32 Clamp rotation motor (movement to the 75-19 must have been
compile position) performed in advance.
2 413
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
M31 34 Glue tank movement motor (home posi- The following adjust-
tion search) ments must have been
made in advance.
1. 75-55
2. 75-29
35 Glue tank movement motor (tank forward The following adjust-
movement ) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
4. 75-49
5. 75-51
36 Glue tank movement motor (tank back- The following adjust-
ward movement ) ments must have been
made in advance.
1. 75-35
2. 75-29
3. 75-34
4. 75-49
5. 75-51
6. 75-35
M32 37 Glue apply roller motor
SD31 38 Glue tank up solenoid /1
SD32 39 Cover paper glue up solenoid
H1 40 Glue tank heater
H2 41 Glue apply roller heater
M33 42 Pellet supply motor The following adjust-
ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
4. 75-44
M34 43 Pellet supply arm motor
(home position search)
44 Pellet supply arm motor The following adjust-
(movement to the supply position) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
M41 45 Cover paper alignment motor 75-55 must have been
(home position search) performed in advance.
414 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(A3 standby position move) ments must have been
made in advance.
1. 75-55
2. 75-45
3. 75-57
4. 75-60
47 Cover paper alignment motor (alignment) The following adjust-
ments must have been
made in advance.
1. 75-55
2. 75-45
3. 75-57
4. 75-60
5. 75-46
M42 48 Book exit motor 75-55 must have been
performed in advance.
M43 49 Cover paper conveyance arm motor /Rt The following adjust-
(home position search) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
50 Cover paper conveyance arm motor /Rt The following adjust-
(roller pressure) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
4. 75-49
M44 51 Cover paper conveyance arm motor /Lt The following adjust-
(home position search) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
52 Cover paper conveyance arm motor /Lt The following adjust-
(roller pressure) ments must have been
made in advance.
1. 75-55
2. 75-29
3. 75-34
4. 75-51
2 415
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
416 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
performed in advance.
63 Cutter motor(cut position movement) 75-55 must have been
performed in advance.
SD41 64 Cover paper lift solenoid
— 65 —
— 66 —
M61 67 Cover paper belt motor
M62 68 Cover paper belt movement motor
(home position search)
69 Cover paper belt movement motor 75-68 must have been
(A4 standby position move) performed in advance.
70 Cover paper belt movement motor
(book stock alignment)
M63 71 Cover paper belt up down motor
(home position search: upper limit)
72 Cover paper belt up down motor The following adjust-
(movement to the lower position) ments must have been
made in advance.
1. 75-68
2. 75-69
M64 73 Book movement motor
M65 74 Book stopper motor
(home position search)
75 Book stopper motor 75-74 must have been
(A4 standby position move) performed in advance.
M73 76 Cover paper tray lift motor
M74 77 Cover paper feed motor
SD71 78 Cover paper pick up solenoid
SD72 79 Cover paper tray solenoid
M71 80 Cover paper tray fan /1
M72 81 Cover paper tray fan /2
MC71 82 Cover paper pick up clutch
MC72 83 Cover paper separation clutch
SD80 84 Front door lock solenoid (locked)
85 Front door lock solenoid (released)
M80 86 Exhaust fan /1
— 87 Multi feed clock output signal
JAMIB/ 88 Jam indicator board /1 /2 (all the lights on)
1
JAMIB/
2
OB/1 89 Manual operation board (all the lights on)
2 417
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
418 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
1000 mm/s)
04 Reverse paper exit motor (F rotation: 520
mm/s)
05 Reverse paper exit motor (F rotation: 290
mm/s)
06 Reverse paper exit motor (R rotation: 520
mm/s)
07 Reverse paper exit motor (F rotation: 825
mm/s)
08 Reverse paper exit motor (F rotation: 425
mm/s)
09 Reverse paper exit motor (R rotation: 825
mm/s)
FM13, 87 00 ADU cooling fan /3
FM14, ADU cooling fan /1
FM15 ADU cooling fan /2
M14 88 01 ADU accelerate motor (1000 mm/s)
02 ADU accelerate motor (490 mm/s)
03 ADU accelerate motor (520 mm/s)
04 ADU accelerate motor (290 mm/s)
05 ADU accelerate motor (825 mm/s)
06 ADU accelerate motor (425 mm/s)
Others — 90 00 Finishing option adjustment data EEPROM Perform after installation
storage (installation data) adjustment
— 91 00 Main body adjustment data parameter Perform after installation
board storage (installation data) adjustment
— 92 00 Parameter board data reset Cannot adjust in the field
— 93 00 Finishing option adjustment data each Cannot adjust in the field
EEPROM storage
— 94 00 Adjustment data display
— 96 00 Main body adjustment data parameter Cannot adjust in the field
board storage (initial data)
— 97 00 Image memory (DRAM) capacity check
— 98 00 Image memory (DRAM) check
HDD1 99 01 HDD1 total capacity
02 HDD1 remaining capacity check
03 HDD1 bad sectors check and recovery
419
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
420
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Output various test patterns to use them for trouble-
shooting.
NOTE
• Do not use any test pattern number not
described in the service manual.
(1) Procedure
421
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[Check item]
• When density is set to 70 (halftone)
If there are white stripes, black stripes, determine whether the fault is with the scanner system or the proc-
ess system.
[Recommended checkpoints]: Developing unit, cleaning unit, charger unit, transfer/separation charger
unit, scanner mirrors, slit glass, original glass
• When density is set to 0 (white)
If the test pattern is gray background image, determine whether the fault is with the process.
[Recommended checkpoints]: Charger, high voltage contact
• When density is set to 255 (black)
If the density is light, determine whether the fault is with the process.
[Recommended checkpoints]: Write unit
* For information about setting the density, see "10.8.2 Test pattern density".
Note
• All print outputs in the user mode are outputted with 1-bit or 2-bit error diffusion. However, since
this pattern is output in 8-bit, an uneven density is apt to conspicuous. Therefore, when check-
ing an uneven density in halftones (other than 0 and 255 in the density setting), be sure to use
the test pattern No. 9.
Test patterns
When the density is set to 70 When the density is set to 0 When the density is set to 255
1050fs3011c
422
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
[Check item]
• Check the pattern to see if the laser output of LD1/LD2 is uniform with the gradation continuously repro-
duced.
[Recommended checkpoints]: Write unit, LD offset adjustment
Test patterns
LD1 LD2
1050fs3054c
423
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[Check item]
• Check the pattern to see if the laser output of LD1/LD2 is uniform with the gradation continuously repro-
duced.
[Recommended checkpoints]: Write unit, LD offset adjustment
*
For LD offset adjustment, see "10.4.2 Drum peculiarity adjustment".
Test patterns
LD1 LD2
1050fs3012c
424
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
[Check item]
• Check if there is any uneven density or transfer jitter.
[Recommended checkpoints]: Moisture absorption of paper, developing unit, charger unit, transfer/sepa-
ration charger unit, transfer jitter adjustment
* For the transfer jitter adjustment see "12.4 Transfer jitter adjustment"
Note
• The density of halftone changes according to the test pattern density adjustment.
• All print outputs in the user mode are outputted with 1-bit or 2-bit error diffusion. However, since
this pattern is output in 8-bit, an uneven density is apt to conspicuous, but less conspicuous
than the test pattern No. 1.
Test patterns
1050fs3055c
425
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[Check Items 1]
• Check the solid black pattern to see if there is uneven density found in the main scan and sub scan direc-
tions.
[Recommended checkpoints]: Charger unit, transfer/separation charger unit, developing unit, writing
dust-proof glass.
[Check Items 2]
• Check to see if there is any image repelling in the gradation pattern at the leading/trailing edge of the test
pattern in the sub scan direction.
[Recommended checkpoints]: transfer/separation charger unit
Test pattern
[1]
[2]
1050fs3013c
426
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
[Check item]
Judge from this test pattern whether the scanner system or the printer system is abnormal.
Items that can be checked include main scan magnification, sub scan magnification, image skew, and leading
edge timing of the printer system. If the copy image is defective despite no abnormality being visible on the
test pattern, the scanner system is defective.
Test pattern
[1]
31mm 237mm
20mm
[1]
190mm
m
0m
28
205.7mm
28
0m
m
190mm
190mm 1050fs3014c
427
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(1) Procedure
428
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
10.9.1
10. Software DIPSW setting
1050e/1050eP
Configure settings for the software DIPSW.
Config
E
NOTE
W bits data are written into the parame-
• DIPSW
ter board
d (PB) every time a change is made.
Do not change
ange data
d hastily, for they cannot
be automatically
lly restored.
res
• Do not change any switch
sw not described in
the service manual.
A. Procedure
[1] [2] [3] [4]
1. Enter the service mode.
2. "Service mode menu screen" [1] DIPSW number
Press the [07 System Setting] key. [2] 8-bit switch values indicated in hexadeci-
3. A sub menu appears on the right side of the mals from 00 to FF.
screen. [3] Bit number (0 to 7)
Press the [01 Software SW Setting] key on the [[4] Bit data: On (1), Off (0)
sub menu.
4. "Software switch setting mode screen"
Press the [S], [T] key or the numeric keys to
select a DIPSW bit number.
5. Press the [On (1)] or [Off (0)] key to set the
selected bit number ON/OFF.
6. Press the [Return] key to return to the "Service
mode menu screen" on which the sub menu
was displayed.
Info HJG:
Siehe DIPSW Liste von HJG
429
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
/1050e/1050eP
• Be sure not to change bits with no particular reference made of the function.
DIPSW
DIP No Bit Function 0 1 Default setting
Japan Inch Metric
DIPSW1
IPSW 0 Print stop condition after toner *1 *
1 0 0 0
1 supply display *
1 *
1 1 1 1
2 Print stop method after toner *2 *2 1 1 1
3 supply display *
2 *
2 0 0 0
4 Pro
Prohibition of printing when the Disabled Enabled 0 0 0
count is reached
PM c
5 Print * *
number setting until print-
nt num 3 3 0 0 0
6 ing is prohibited
prohib after PM is *
3 *
3 0 0 0
7 displayed
ed *
3 *
3 0 0 0
DIPSW2 0 — — — 0 0 0
1 All charger cleaning
aning cycle
c (fix- * *
4 4 0 0 0
2 ing temperature 50°C o
or less *4 *4 0 0 0
3 when turning ON) *
4 *
4 0 0 0
4 e (afte
All charger cleaning cycle (after * *
5 5 0 0 0
5 turned ON) *5 *5 0 0 0
6 Blade auto replacement cycle *6 *6 0 0 0
7 * *
6 6 0 0 0
DIPSW3 0 Transfer assist timing adjust- Disa
Disabled Enabled 1 1 1
ment
1 SC latch (SC23-14, 23-17, 34-**, 35-**, 36-**, Unlatched
ched Latched 0 0 0
78-40 to 62)
2 — — — 0 0 0
3 Charger cleaning function Enabled Disabled
D 0 0 0
4 Transfer/separation charger Enabled Disabled
Disa 0 0 0
cleaning function
5 — — — 0 0 0
6 I/O check mode output 15 Disabled Enabled
ed 0 0 0
memory clear
7 PageScope JobEditor recognition Disabled Enabled 0 0 0
DIPSW4 0 RADF auto skew adjustment Enabled Disabled 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 Key counter removal recovery Disabled Enabled 0 1 0
5 APS when change magnification Enabled Disabled 0 1 0
6 — — — 0 0 0
430 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(other than PM counter)
DIPSW5 0 Causes a message to notify a 65 to 80%: Near- 45 to 65%: Near- 0 0 0
waste toner full status when full full
using RC. 80% or more: Full 60% or more: Full
1 Printer operation at waste toner Not allowed Allowed (switched to 0 0 0
full status (SC23-50) toner recycling mode)
*7 *7
2 Image density selection (laser 0 0 0
3 PWM) for copier *
7 *
7 0 0 0
4 D
Display of CMS button of the * *
8 8 0 0 0
toner collection box
tone
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW6 0 Background
nd density
den adjust- *9 *9 0 0 0
1 ment (photo mode) *
9 *
9 1 1 1
2 ontrol
Transfer assist control Enabled Disabled 0 0 0
3 Minimum black band width in
nd wid * *
10 10 0 0 0
4 black band creation control
ontrol *
10 *
10 0 0 0
5 Image stabilization controll *11 *11 0 0 0
6 cycle *
11 *
11 1 1 1
7 Drum potential auto adjust- Enabled Disabled 0 0 0
ment
DIPSW7 0 — — — 0 0 0
1 — — — 0 0 0
2 * *
Background density adjustment 12 12 0 0 0
3 * *
12 12 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 * *
Control to change the black band 13 13 0 0 0
width
* *
DIPSW8 0 Image density selection (laser 14 14 0 0 0
1 PWM) for printer *
14 *
14 0 0 0
2 Fusing initial rotation condition * *
15 15 0 0 0
3 * *
15 15 1 1 1
4 Fusing initial rotation time * *
16 16 0 0 0
5 * *
16 16 0 0 0
6 Large-size paper count Count as 1 Count as 2 0 0 0
method (PM counter)
7 Page number dash length for Long (⎯ 1 ⎯) Short (- 1 -) 0 0 0
Stamp/Overlay mode
2 431
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
432 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
1 Original size detection switchover 2 A4S 8 / x 11S
12 0 1 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 Original size detection switcho- * *
24 24 0 0 0
6 ver 3 *
24 *
24 0 0 0
7 * *
24 24 1 1 0
DIPSW14 0 Original size detection switcho- B4, 11 x 17/B5, 8K/16K/16KS 0 0 0
ver 4
ve 8 /2 x 11/B5S
1
1 Wider
Wider-sized paper + punch Limited Not limited 0 0 0
pport in printer mode
support
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW15 0 CMS function Not use Use 0 0 0
1 Number of "Fine" paper that
at *25 *25 0 0 0
2 can be stapled *25 *25 0 0 0
3 Finishing option alarm stop *26 *26 0 0 0
4 *2
26 *26 0 0 0
5 CS Remote Care recognition Disabled
isabled Enabled 0 0 0
6 Maximum density in printer mode 1.43
43 1.35 0 0 0
7 Trigger the display of developer/ Number of prints Running time 0 0 0
drum replacement icon
DIPSW16 0 Developer/drum running time Displayed Not displayed 0 0 0
display
1 Copy reservation function Enabled Disabled
Disable 0 0 0
2 — — — 0 0 0
3 Count of the key counter in Disabled Enabled
d 0 0 0
printer mode
4 Utility mode installation date Enabled Disabled 0 0 0
display
5 Non-image area erase mode * *
27 27 0 0 0
6 judge level *
27 *
27 0 0 0
7 NIC selection for E-Mail CS Controller NIC Machine NIC 0 0 0
Remote Care
2 433
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
* *
1 28 28 1 1 1
* *
2 28 28 1 1 1
* *
3 28 28 0 0 0
* *
4 Density selection at scanning 29 29 0 0 0
5 tab paper *
29 *
29 0 0 0
* *
6 29 29 0 0 0
7 Switching of custom size Not rotate Rotates 1 1 1
paper in printer mode
DIPSW18 0 Faulty part isolation: Tray /1 Normal Unavailable 0 0 0
1 Faulty part isolation: Tray /2 Normal Unavailable 0 0 0
2 Faulty part isolation: Tray /3 Normal Unavailable 0 0 0
3 Faulty part isolation: Tray /4 Normal Unavailable 0 0 0
4 Faulty part isolation: RADF Normal Unavailable 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Faulty part isolation: HDD1 Normal Unavailable 0 0 0
* *
DIPSW19 0 Fusing temperature setting 29 29 0 0 0
* *
1 29 29 0 0 0
* *
2 29 29 0 0 0
* *
3 29 29 0 0 0
* *
4 Black band width when the 31 31 0 0 0
inside temperature is high
5 — — — 0 0 0
* *
6 Maximum black band width 32 32 0 0 0
7 (when connecting RC) *
32 *
32 0 0 0
DIPSW20 0 Group staple Disabled Enabled 0 0 0
* *
1 Image scanning area with 33 Normal 33 Original priority 0 0 0
image shift
2 Total page number standard in Based on original Based on 0 0 0
stamp mode transfer paper
3 Keyboard layout ABC layout QWERTY layout 0 0 0
4 Faulty part isolation: Tray /5 Normal Unavailable 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Tandem connection *34 *34 0 0 0
DIPSW21 0 Mixed size paper staple Allowed Prohibited 0 0 0
(real-time output) (batch output)
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
434 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
scanning: 182mm scanning: 150mm
sub scanning: sub scanning:
140mm 132mm
5 Touch panel adjustment method Utility/setting but- hard key 0 0 0
ton +hard key
6 Target settings to judge Target settings Not target settings 0 0 0
unmatched paper type in front (not overwrites the
and back registrations value of front and back reg-
a job read out from HDD istrations value)
7 — — — 0 0 0
DIPSW22 0 Machine
achine NIC setting Disabled Enabled 1 1 1
1 Number
ber of punch holes * *
35 35 1 1 0
2 *35 *35 0 0 1
3 Image position
on for tthe non-stan- Based on user Based on APS at 0 0 0
dard size original
al (at DF)
D selection DF
4 er save button
Function of power Enabled Disabled 0 0 0
5 SD trimmer board moving tim- Not displayed Displayed 0 0 0
ing adjustment
6 mpty
Operation when staple empty Request staple Selectable staple 0 0 0
of FNS supply supply or staple
release
7 Jam screen selection Jam position Described by 0 0 0
display
disp illustration
DIPSW23 0 — — — 0 0 0
1 — — — 0 0 0
2 Toner density of developer * *
36 36 0 0 0
3 selection *
36 *
36 0 0 0
4 *36 *36 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW24 0 — — — 0 0 0
1 Default settings of PageScope Manual Automatic 0 0 0
JobEditor when turned ON
2 — — — 0 0 0
3 — — — 0 0 0
4 Z-fold output number limit *37 *37 0 0 0
5 * *
37 37 0 0 0
6 Z-fold + Staple output number * *
38 38 0 0 0
7 limit *
38 *
38 0 0 0
DIPSW25 0 PI size detection switchover 1 A5 5.5 x 8.5 0 1 0
1 PI size detection switchover 2 A4S 8.5 x 11S 0 1 0
2 435
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
* *
3 39 39 0 0 0
* *
4 39 39 1 1 0
5 PI size detection switchover 4 B4, 11 x 17/B5, 8K/16K/16KS 0 0 0
8 /2 x 11/B5S
1
436 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
shifting direction specified two
repeat.
7 SD-501 Limitation for multi half Limited Not Limited 0 0 0
fold
DIPSW
DIPSW29 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 Switching of suction fan /4
Sw Idling ON for 10 minutes 0 0 0
(FM29) operation control
(FM2 OFF after finishing printing
(when the drum tem-
perature is 45°C
or more)
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW30 0 — — — 0 0 0
1 Service mode, restriction
tion of Restricted Not restricted 0 0 0
data collection display
2 — — — 0 0 0
3 — — — 1 1 1
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW31 0 — — — 1 1 1
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW32 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
2 437
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
punch function
1 — — — 0 0 0
2 Faulty part isolation: FD main Normal Unavailable 0 0 0
tray paper exit
3 Faulty part isolation: PI function Normal Unavailable 0 0 0
4 Faulty part isolation: FD Normal Unavailable 0 0 0
5 — — — 0 0 0
6 Faulty part isolation: LS main
Fault Normal Unavailable 0 0 0
tray-tandem
ay-tan (1st)
7 Faulty
ty part isolation: LS main Normal Unavailable 0 0 0
tray-tandem
ndem (2nd)
DIPSW34 0 Faulty partt isolation:
isolat SD saddle Normal Unavailable 0 0 0
stitch
1 Faulty part isolation: SD multi
tion: S Normal Unavailable 0 0 0
center fold
2 Faulty part isolation: SD mu
multi Normal Unavailable 0 0 0
tri-fold
3 m-
Faulty part isolation: SD trim- Normal Unavailable 0 0 0
ming
4 Faulty part isolation: SD con- N
Normal Unavailable 0 0 0
nection/ sub-tray exit
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW35 0 Faulty part isolation: FS staple Normal Unavailable 0 0 0
function
1 Faulty part isolation: FS main Normal Unavailable
Unav 0 0 0
tray paper exit
2 Faulty part isolation: FS Normal ailable
Unavailable 0 0 0
3 Faulty part isolation: PB cover Normal Unavailable
able 0 0 0
paper insertion
4 Faulty part isolation: PB binder Normal Unavailable 0 0 0
function
5 Faulty part isolation: PB Normal Unavailable 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW36 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
438 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
7 — — — 0 0 0
DIPSW37 0 — — — 0 0 0
1 — — — 0 0 0
2 PB perfect binding limit Enabled Disabled 0 0 0
(includes Z-fold)
3 Upper limit setting for the num- Limited according Limited accord- 0 0 0
ber of papers to be stapled to paper size, paper ing to the paper
weight, or paper size
type, whichever is
the minimum.
4 Upper limit
l setting for the num- Limited by the Limited by the 0 0 0
ber of papers
pap to be ejected for software FS-503 main tray
stapling
g or fo
folding lower limit sensor
5 — — — 0 0 0
6 — — — 1 1 1
7 — — — 0 0 0
DIPSW38 0 Default folder when
n selecting
selec Private folder Shared folder 0 0 0
box function
1 File name overwriting with box functio
function Disabled Enabled 0 0 0
2 age
Print quantity and output page Enabled Disabled 0 0 0
selection for Wait or Proof out-
put for box function
3 — — — 0 0 0
4 Automatic change of tray set- * *
42 42 0 0 0
ting names
5 Peripheral image erasure of d
Disabled Enabled 0 0 0
custom size
*43 *43
6 Buck side trailing edge erasure 0 0 0
7 amount with duplex output * *
43 43
4 0 0 0
DIPSW39 0 Tray1 paper leading edge Disabled Enable
Enabled 0 0 0
buckling prevention control
1 Tray2 paper leading edge Disabled Enabled
ed 0 0 0
buckling prevention control
2 Tray3 paper leading edge Disabled Enabled 0 0 0
buckling prevention control
3 Tray4 paper leading edge Disabled Enabled 0 0 0
buckling prevention control
4 Tray5 paper leading edge Disabled Enabled 0 0 0
buckling prevention control
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
2 439
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
1 — — — 0 0 0
2 Cover sheet single fold control * *
44 44 0 0 0
3 with folding&stapling/multi * *
44 44 0 0 0
center
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW42 0 TIFF direct
d print Not output Output 0 0 0
1 TIFF direct print
F direc * *
45 45 0 0 0
2 APS target paper size (F4)
arget p *45 *45 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW43 0 Change of the scanner com-
om- MMR MH 0 0 0
pression method
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 1 1 1
7 — — — 0 0 0
DIPSW46 0 Visual Counter Master counter * *
46 46 0 0 0
1 value read-off intervals *
46 *
46 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
440 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
*
1 Print stop condition after toner supply display
Every 20,000 prints 0 1
Mode 1-1 1-0
Every 30,000 prints 1 0
Stops after 500 prints 0 0
Every 5,000 prints 1 1
Stops after 750 prints 0 1
Stops after 1,000 prints 1 0 *6 Blade auto replacement cycle
Stops after 2,000 prints 1 1
Mode 2-7 2-6
*2 Print stop method after toner supply display Every 375,000 prints 0 0
Every 250,000 prints 0 1
Mode 1-3 1-2
Every 300,000 prints 1 0
Stops after exit paper in the 0 0
Every 500,000 prints 1 1
machine
Stops at a break between 0 1 *7 Image density selection (laser PWM) for copier
print set Change the image writing laser PWM to change image
Stops at the end of the cur- 1 0 density.
rent job
Does not stop 1 1 NOTE
• There are two kinds of DIPSWs to lighten image
*3 Print number setting until printing is prohibited after density: laser PWM (5-2/3) and toner control patch
PM is displayed density (27-2/3). As a priority of adjustment,
adjust in the following order.
Mode 1-7 1-6 1-5
1) Laser PWM
1,000 prints 0 0 0 2) Toner control patch density: approx. 0.5%
2,000 prints 0 0 1 down
3,000 prints 0 1 0 Using this setting alone may cause white spot
4,000 prints 0 1 1 on the solid section. Be sure to use together
2 441
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
442 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
So, rotate the fusing roller while in the warm-up to
obtain an even heat distribution of the fusing roller to 1 prints 0 0 0 1
avoid the insufficient fusing. 3 prints 0 0 1 0
In this adjustment, determine the environment in 5 prints 0 0 1 1
which you implement the fusing initial rotation. 9 prints 0 1 0 0
• Low temperature: perform the fusing initial rotation
10 prints 0 1 0 1
in the low temperature environment only.
20 prints 0 1 1 0
• Low/normal temperature: perform the fusing initial
rotation in the low and normal temperature envi- 30 prints 0 1 1 1
ronment 50 prints 1 0 0 0
• Low/normal/high temperature: perform the fusing 99 prints 1 0 0 1
initial rotation in all environments. No limit 1 0 1 0
300 sec 0 1 image memory; DRAM on IPB and hard disk/1 (10
GB of total 40 GB is used). DRAM is used by priority.
60 sec 1 0
If hard disk/1 is damaged and memory overflow
0 sec 1 1
occurs during scanning or transferring data from PC,
increase compression memory. If memory overflow
*17 Message switchover
occurs before printing starts, increase expansion
Mode 9-3 9-2 memory.
2 443
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Mode 12-0
Disabled 0
Enabled 1
444 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
50 sheets 0 1 130 minutes 1 1 0 1
2 445
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
*31 Black band width when internal temperature *35 Number of punch holes
Black band is created with the width set in DIPSW6-
Mode 22-2 22-1
3, 4 when "1" is selected for this setting and the drum
/1050e/1050eP
446 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
bias for the toner control patch formed on the drum
8 sheets 0 1 to determine the toner density.
10 sheets 1 0
3 sheets 1 1 NOTE
• After changing the DIPSW, image density
*39 PI size detection switchover 3 does not appear as the setting value until
Default setting for inch is 8.5 x 14 and 8 x 13 for met- printing about 500 prints because it needs to
ric. add toner to increase the toner density of
developer or consume toner to reduce it.
Mode 25-4 25-3 25-2 • Using this setting alone may cause image
8 x 13 0 0 0 background or toner spillage. Be sure to use
8 /4 x 13
1
0 0 1 together with DIPSW23-2/3/4 (toner density
81/8 x 131/4 0 1 0 of developer) approx. 0.5% down or 1.0%
down.
81/2 x 13 0 1 1
• There are two kinds of DIPSWs to lighten
81/2 x 14 1 0 0
image density: laser PWM (5-2/3) and toner
Not used 1 0 1
control patch density (27-2/3). For the priority
Not used 1 1 0 of adjustment, adjust in the following order.
Not used 1 1 1 1) Laser PWM
2) Toner control patch density: approx. 0.5%
*40 Transfer assist control size switchover down
Default setting for inch is "Between 279 mm and 297 Using this setting alone may cause white
mm" and "297 mm or more" for metric. spots on the solid section. Be sure to use
together with DIPSW23-2/3/4 (toner den-
NOTE sity of developer) approx. 0.25% up or
• When you make the transfer assist sheet 0.5% up.
PCS-compliant, be sure to set this switch to
"Correspond to PCS." Mode 27-3 27-2
Standard 0 0
Approx. 0.5% up 0 1
Mode 26-1 26-0
Approx. 1.0% up 1 0
297 mm or more 0 0
Approx. 0.5% down 1 1
Between 279 mm and 0 1
297 mm
*42 Tray name is automatically changed.
Do not transfer assist 1 0
Correspond to PCS 1 1 Mode 38-4
Automatically changes the name to 0
the name of selected paper type,
when the name has been set to
"paper type".
Automatically changes the name to 1
the name of selected paper type,
when paper type, paper weight, color,
and punch settings are changed.
2 447
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
*43 Buck side trailing edge erasure amount with 10.9.2 Telephone number setting
duplex output Set the telephone number and FAX number of the
service center displayed when malfunction occurs.
Mode 38-7 38-6
/1050e/1050eP
448 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
When setting the DIPSW 16-4 to 1, the starting date
of the total counter is not displayed.
Caution:
• Never change the serial number of the main
A. Procedure
body. Otherwise, the fixing temperature
abnormality or the drum damage may occur. 1. Enter the service mode.
2. "Service mode menu screen"
A. Procedure Press the [07 System Setting] key.
3. A sub menu appears on the right side of the
1. Enter the service mode. screen.
2. "Service mode menu screen" Press the [04 Setting Date Input] key on the
Press the [07 System Setting] key. sub menu.
3. A sub menu appears on the right side of the 4. "Setting date input screen"
screen. Enter the starting date through the numeric
Press the [03 M/C Serial Number Setting] key keys.
on the sub menu. 5. Press the [OK] key to update data.
4. "Serial number setting mode screen" Press the [Cancel] key to cancel the setting you
Press the key for the option you want to set, updated.
and enter the serial number through the
numeric keys.
5. Press the [OK] key to register data.
Press the [Cancel] key to cancel the setting you
entered.
NOTE
• When the entered data is incorrect, a notice
screen appears. Press the [OK] key to close
the screen and enter data again.
449
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
options.
NOTE
• The [Image control] that is displayed on the
screen represents the ROM version of the
overall control board (OACB).
(1) Procedure
450
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
The CS Remote Care is a system that manages the main body by sending and receiving various kinds of the
management data of the main body between the main body and the CS Remote Care center computer through
the phone line or E-mail.
It enables the main body to call the center computer, and the center computer to inquire regularly the main body
for various data.
The data handled by the CS Remote Care can be classified into the 3 following groups.
a. Data that allow you to grasp the use conditions of the main body, such as the total count and the PM count.
b. Data that give us the general information of when and how often an abnormality occurred with the main body.
c. All sorts of adjustment data
Note
• When the security enhanced mode is set to ON, the use of the main body NIC is not allowed.
Step Operation
When using the phone line modem When using the E-mail
Main body NIC Controller NIC
0 Registered the machine ID in the application on the CS Remote Care center side.
When the machine ID is not registered, no initial connection cannot be made.
1 Modem connection When using the E-mail, remove the modem for the
Turn off the power of the modem, connect the phone line.
main body and the modem with a modem cable,
and the modem and the wall outlet with a modu-
lar cable.
* For the connection of a modular cable, see the
instructions of the modem to be used.
2 I/O check mode and data collection clear available
(Service mode → 07 System Setting → 01 Software SW Setting → Set 03-6 to "On (1)")
3 CS Remote Care memory initialization
(Service mode → 04 Machine Condition → 01 I/O Check Mode → [1] [5] [ACCESS] [9] [8] → [Start]
button ON)
4 CS Remote Care function ON
(Service mode → 07 System Setting → 01 Software SW Setting → Set 15-5 to "On (1)")
451
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Step Operation
When using the phone line modem When using the E-mail
Main body NIC Controller NIC
/1050e/1050eP
452
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
13 DIPSW setting for the CS Remote Care Proceed to the step 14.
(Enter the No. code → Detail setting → Software
SW setting)
(Baud rate setting: Select the baud rate at the
software DIPSW setting 01-4 to 7.)
14 Turn on and off the power switch (SW2) of the main body.
15 First call execution Initial connection mail Initial connection mail
(Service mode → 09 CS Remote Care → 01 CS reception reception
Remote Care → Press No. Code twice → Detail The initial connection The initial connection
setting → 01 Basic setting → First call*) mail is sent to the mail mail is sent to the mail
* When the connection to the center completes address of the main address of the controller
successfully, the CS Remote Care setting screen body NIC from the cen- NIC from the center.
is displayed. ter. * When the CS Remote
* When the CS Remote Care related window is
Care related screen is opened while receiving
opened while receiving the initial connection
the initial connection mail from the center, the
mail from the center, the information being cre-
information being cre- ated is destroyed and
ated is destroyed and the CS Remote Care
the CS Remote Care setting screen is dis-
setting screen is dis- played.
played.
453
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
10.11.3 List of combinations of E-Mail CS Remote Care and Mail remote notification system
To change a combination of E-Mail CS Remote Care and Mail remote notification system, refer to this table to
configure the DIPSW setting or the mail account setting.
/1050e/1050eP
454
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(default)
2. "Service mode menu screen"
6. Press the [Return] key to finish the configura-
Press the [07 System Setting] key.
tion.
3. "Sub menu screen"
Press the [01 Software SW Setting] key.
4. "Software SW Setting screen" D. NIC selection for E-Mail CS Remote Care
Set "03" with the DIPSW number.
1. Enter the service mode.
Set "6" with the DIPSW bit number.
2. "Service mode menu screen"
5. Set the bit data to "On (1)".
Press the [07 System Setting] key.
On (1): I/O check mode, data collection clear
enabled 3. "Sub menu screen"
Off (0): I/O check mode, data collection clear Press the [01 Software SW Setting] key.
disabled (default) 4. "Software SW Setting screen"
6. Press the [Return] key to finish the configura- Set "16" with the DIPSW number.
tion. Set "7" with the DIPSW bit number.
5. Set the bit data to the NIC you use.
On (1): Use the main body NIC
B. CS Remote Care memory initialization Off (0): Use the controller NIC (default)
6. Press the [Return] key to finish the configura-
1. Enter the service mode.
tion.
2. "Service mode menu screen"
Press the [04 Machine Condition] key.
3. "Sub menu screen" E. CS Remote Care function selection (E-Mail/
Press the [01 I/O Check Mode] key. Phone line modem)
4. "I/O Check Mode screen"
1. Enter the service mode.
Enter "15" with the numeric keys. Confirm that
"15-00" is displayed on the message display 2. "Service mode menu screen"
area. Press the [09 CS Remote Care] key.
455
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12. "Date and Time setting screen" *1 When entering the telephone number, keys on
Enter the year in 2 digits with the numeric keys, the screen other than numeric keys represent
and press the [Set] key. the followings.
/1050e/1050eP
13. Enter time with the numeric keys, and press the [ , ] Pause: holds the self-dial delivery for some time
[Set] key. [W] Wait: detects the destination dial tone
14. Press the [Time Zone] key. [T] Tone dial: tone dialing
[P] Pulse dial: pulse dialing
15. Enter the time zone with the numeric keys, and
[—] Number delimiter: ignored when actually dialed
press the [Set] key.
[*] [#] [•]: use as necessary
16. Press the [OK] key to return to the "Setting
*2 Change the modem initialization command if
menu screen."
necessary (Usually, there is no need to change).
* Enter the No. code that is assigned in advance. For details, refer to the manual of the modem.
456
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
NOTE
2. "Basic setting screen" • DIPSW bits data are written into the Parame-
Press the [Center No.] key. ter board (PB) every time a change is made.
3. Enter the center ID with the keyboard, and In case you changed bit data by accident, be
press the [OK] key. sure to restore the previous state.
4. Press the [OK] key to return to the "E-Mail Set-
ting Menu screen." A. Input procedure
5. "E-Mail Setting Menu screen"
1. Enter the service mode.
Press the [03 Response time out setting] key. *
2. "Service mode menu screen"
6. Enter the response time out time with the
Press the [09 CS Remote Care] key.
numeric keys. (in minutes)
3. "Sub menu screen"
7. Press the [OK] key to return to the "E-Mail Set-
Press the [01 CS Remote Care] key.
ting Menu screen."
4. "CS Remote Care setting screen"
Press the [No. Code] key.
NOTE
• The response time out setting is automati- 5. Use the sheet setting keys to enter the No.
cally set on receiving the initial connection code. *1
mail. Change the setting if necessary. 6. Press the [No. Code] key.
7. Press the [Detail setting] key.
8. "Setting menu screen"
Press the [05 Software SW Setting] key.
9. "Software SW Setting screen"
Select the DIPSW number.
Use the left arrow key or the numeric keys.
10. Select the DIPSW bit number.
Use the right arrow key or the numeric keys.
11. Select DIPSW On (1), Off (0).
Use the [On (1)], [Off (0)] key.
12. Press the [Return] key to return to the "Setting
menu screen."
*1 If the No. code is already entered, confirm that
No. code.
NOTE
• About functions of each switch, see to "B.
List of software DIPSW for CS Remote Care".
457
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
/1050e/1050eP
458
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
2 *6 *6 1
3 *6 *6 0
4 to 7 — — — 0
DIPSW9 0 Retransmission times on E-Mail delivery *7 *7 0
1 error *7 *7 1
2 *7 *7 0
3 *7 *7 1
4 *7 *7 0
5 *7 *7 0
6 *7 *7 0
7 — — — 0
DIPSW10 0 Time zone setting *8 *8 0
1 *8 *8 0
2 *8 *8 0
3 *8 *8 0
4 *8 *8 0
5 *8 *8 0
6 *8 *8 0
7 *8 *8 0
DIPSW11 0 Timer 1 *9 *9 0
1 RING reception → CONNECT reception *9 *9 0
2 *9 *9 0
3 *9 *9 0
4 *9 *9 0
5 *9 *9 1
6 *9 *9 0
7 *9 *9 0
DIPSW12 0 Timer 2 *10 *10 0
1 Dial request completed → CONNECT *10 *10 0
2 reception *10 *10 0
3 *10 *10 0
4 *10 *10 0
5 *10 *10 0
6 *10 *10 1
7 *10 *10 0
DIPSW13 0 Timer 3 — — 0
1 Not used — — 1
2 — — 0
3 — — 1
4 — — 0
459
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
7 — — 0
DIPSW14 0 Timer 4 *11 *11 0
1 Line connection → Start request telegram *11 *11 0
2 delivery *11 *11 0
3 *11 *11 0
4 *11 *11 0
5 *11 *11 1
6 *11 *11 0
7 *11 *11 0
DIPSW15 0 Timer 5 *12 *12 0
1 Wait time for other side's response *12 *12 1
2 *12 *12 1
3 *12 *12 1
4 *12 *12 1
5 *12 *12 0
6 *12 *12 0
7 *12 *12 0
DIPSW16 0 Retry data, timer 6 *13 *13 1
1 Initialization OK → Dial request *13 *13 1
2 *13 *13 1
3 *13 *13 1
4 *13 *13 1
5 *13 *13 1
6 *13 *13 1
7 *13 *13 1
DIPSW17 0 Call JAM date (main body) *14 *14 1
1 Valid copy quantity *14 *14 0
2 Call ADF JAM date *15 *15 1
3 Valid original feed quantity *15 *15 0
4 Call JAM date *16 *16 1
5 MCBJ setting *16 *16 0
6 Call ADF JAM date *17 *17 1
7 MOBJ setting *17 *17 0
DIPSW18 0 Attention display Do not call Call 1
1 to 7 — — — 0
DIPSW19 to 0 to 7 — — — 0
DIPSW40
460 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
Issue ATA by RING delivery 10 minutes 0 0 0 1
Do not receive 1 20 minutes 0 0 1 0
Do not issue ATA by RING delivery 30 minutes 0 0 1 1
40 minutes 0 1 0 0
*2 Baud rate
50 minutes 0 1 0 1
Mode 01-7 01-6 01-5 01-4 60 minutes 0 1 1 0
1200 bps 0 0 1 1 70 minutes 0 1 1 1
2400 bps 0 1 0 0 80 minutes 1 0 0 0
4800 bps 0 1 0 1 90 minutes 1 0 0 1
9600 bps 0 1 1 0 100 minutes 1 0 1 0
19200 bps 0 1 1 1 110 minutes 1 0 1 1
38400 bps 1 0 0 0 120 minutes 1 1 0 0
57600 bps 1 0 0 1
*7 Retransmission times on E-Mail delivery error
*3 CS Remote Care communication mode
Mode 6 5 4 3 2 1 0
Mode 03-1 03-0 DIPSW09
Data modem 0 0 0 to 9 times 000 0000 to 000 1001
FAX (not used) 0 1 10 times 0 0 0 1 0 1 0
E-Mail 1 0 11 to 99 times 000 1011 to 110 0011
Reservation 1 1
*8 Time zone setting
*4 Modem redial interval
Mode 7 6 5 4 3 2 1 0
Mode 05-3 05-2 05-1 05-0 DIPSW10
1 minute 0 0 0 1 -12 to -1 1111 0100 to 1111 1111
2 minutes 0 0 1 0 0 0 0 0 0 0 0 0 0
3 minutes 0 0 1 1 1 to 12 0000 0001 to 0001100
4 minutes 0 1 0 0
*9 Timer 1 (RING reception → CONNECT recep-
5 minutes 0 1 0 1
tion)
6 minutes 0 1 1 0
7 minutes 0 1 1 1 Mode 7 6 5 4 3 2 1 0
8 minutes 1 0 0 0 DIPSW11
10 minutes 1 0 1 0 32 sec 0 0 1 0 0 0 0 0
33 to 255 sec 0010 0001 to 1111 1111
*5 Modem redial times
Mode 6 5 4 3 2 1 0
DIPSW06
0 to 9 times 000 0000 to 000 1001
10 times 0 0 0 1 0 1 0
11 to 99 times 000 1011 to 110 0011
461
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
*10 Timer 2 (Dial request completed → CONNECT *15 Call ADF JAM date
reception) Valid original feed quantity
*11 Timer 4 (Line connection → Start request tele- *16 Call JAM date
gram delivery) MCBJ setting
Mode 7 6 5 4 3 2 1 0
DIPSW16
0 to 254 (x 5 msec) 0000 0000 to 1111 1110
255 (x 5 msec) 1 1 1 1 1 1 1 1
462 1
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
is connected to this machine by the network to set
the mail address. The mail setting method of the CS
Remote Care that uses the main body NIC is the
same as that for the mail remote notification system.
Corresponding browser: Internet Explorer 5.5 or
Netscape4.7x or above
463
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
The setting method of the CS Remote Care and 5 received mail logs. The CS Remote Care
that uses the main body NIC is the same as related mails are displayed as "Kind: CS Remote
that of the mail remote notification system. Care Mail."
• Sending mail (SMTP) server:
Set the IP address of the sending mail server.
B. Procedure for setting the Controller NIC
• Interval between fetching mails:
Set the intervals from 1 minute to 60 minutes to 1. Press the [Utility] button on the operation panel.
check the receiving mail server to see if a mail is
2. "Utility menu screen"
newly received.
Press the [06 Machine Manager Setting] key.
• Receiving mail server:
3. "Machine manager setting menu screen"
Set the IP address of the receiving mail server.
Press the [04 Network Setting] key.
• Kind of mail spool:
Select either of POP3 and IMAP according to 4. "Sub menu screen"
the mail server to be used by the main body. Press the [02 Controller NIC Setting] key.
464
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• POP Server Address nection with the center.
Specify the POP server address. You can use
1. Enter the service mode.
symbols and alphanumeric characters within
2. "Service mode menu screen"
63 characters.
Press the [09 CS Remote Care] key.
• User Name
Enter the user name to login to the POP server. 3. "Sub menu screen"
You can use symbols and alphanumeric char- Press the [01 CS Remote Care] key.
from 30 to 300 (sec). Default is [60] seconds. When properly completed, the "CS Remote
Care setting screen" appears.
Press the [Next] key to configure the following two *1 If the No. code is already entered, confirm that
settings. No. code.
• Auto Check *2 In case an error occurred in the communication
Select [Yes]. with the center, check the displayed code. For
• Auto Check Interval Time details on error codes, see "10.11.14 Error code
Specify the interval between checking new list".
mails within the range from 1 to 60 (minutes).
Default is 15 minutes.
11. Press the [OK] key.
12. "CSRC setting menu screen"
Press the [03 CSRC Communication Test] key.
13. "CSRC Communication Test"
Press the [Start] key.
Confirm that the sending and receiving are cor-
rectly performed and go to next step. If the test
failed, re-confirm the settings and perform the
test again following the error message.
465
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
connection mail to the mail address of the main body, 2. "Service mode menu screen"
thus enabling mail transmission between the center Press the [09 CS Remote Care] key.
and the main body. 3. "Sub menu screen"
Press the [01 CS Remote Care] key.
MEMO: 4. "CS Remote Care setting screen"
• About how to send the initial connection mail, refer Make sure that only selected items for
to the CS Remote Care center's manual. "Modem" or "E-Mail" are displayed.
• Mail transmission are possible only between the
center and the main body that the initial connec-
tion has been established.
• The initial connection mail is sent from the center.
The mail address of the center used then is stored
in the main body.
• To check the center's mail address on the main
body, output "Machine Management List." Proce-
dure: Service mode → 05 List Output → 01 List
Output → Machine Management List. Press the
[COPY] key at upper left of the screen to output
the list from the basic screen.
466
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
fied, managed by a distributor.) to notify the center
1. Enter the utility mode.
the start of maintenance. After the maintenance,
pressing the maintenance completion key notifies the 2. "Utility Menu screen"
center the completion of maintenance. Press the [06 Machine Manager Setting] key.
3. "Machine manager setting menu screen"
<At the start of maintenance> Press the [06 System Connection] key.
4. "Sub menu screen"
1. Enter the service mode.
Press the [01 User Call] key.
2. "Service mode menu screen"
5. "User Call screen"
Press the [09 CS Remote Care] key.
Press the [Start] key.
3. "Sub menu screen" If the setup is not completed, or if other call is
Press the [01 CS Remote Care] key. made, the [Start] key is grayed out, disabling to
4. "CS Remote Care setting screen" make a call.
Press the [No. Code] key.
5. Enter the No. code with the numeric keys. About how to call the center and send various data of
6. Press the [No. Code] key. the main body on the specified date and time, refer to
the CS Remote Care center's manual.
During the maintenance, the [Start] button blinks until
the completion of the maintenance.
467
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
*
1 If the No. code is already entered, confirm that
No. code.
468
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
timed out).
K00_01 No response (After connection, no start telegram Redial and wait for re-reception.
from the center detected).
K00_02 Copying. Could not be written in non-volatile mem-
ory, and line disconnected.
K00_03 Center ID mismatch. Confirm the center ID.
K00_04 Serial number mismatch. Confirm the serial number.
K00_05 Grammar error (when receiving undefined com- Redial.
mands or parameters).
K00_06 Received a write order for an unwritable item.
K00_07 Unread item error.
K00_08 Signal reception time out after a response detection Redial.
(after the start telegram shuttled).
K00_09 Already registered serial number.
K00_10 Communication error occurred because of the car- Redial.
rier OFF (NO CARRIER detected in the modem).
K00_11 Dialtone (NO DIALTONE) detected in the modem. Redial.
K00_12 Busy signal (BUSY) detected in the modem. Redial.
K00_13 NO ANSWER detected in the modem. Redial.
K00_14 Telegram error (irregular telegram received in Retry standard times, and redial.
response to the telegram you sent).
K00_15 Serial number not registered in the center (4 x 40
telegrams received).
K00_16 Errors not defined in the above -00 to 15 (last 2 dig- Redial.
its).
K00_17 Telephone number you must call was not registered.
469
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
10.11.15 Troubleshooting
Check the followings when the main body neither receives the initial connection mail nor returns a response.
1) The center ID or the machine ID are not set in the main body.
2) The center ID or the machine ID are different (A machine ID error is not returned at the initial connection).
3) CS Remote Care function is disabled, or the phone line is selected in the CS Remote Care function selection.
4) Communication between the main body and the mail server is not proper (Check this with a transmission
test).
470
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3. A sub menu appears on the right side of the screen. 1. Enter the service mode.
Press the [01 Staple Position Adj.] key on the sub 2. "Service mode menu screen"
menu. Press the [11 Finisher Adjustment] key.
4. "Staple Finisher adjustment mode screen" 3. A sub menu appears on the right side of the screen.
Press the [01 Stapling Center Position Adjustment] Press the [01 Stapler Position Adj.] key on the sub
key. menu.
5. "Stapling Center Position Adjustment screen" 4. "Staple Finisher adjustment mode screen"
Press the [COPY] key. Press the [02 Paper Width Adjustment] key.
6. Select A3 or 11 x 17 paper, and select the 2 sta- 5. "Stapling Paper Width Adj. screen"
plings. Press the Start button to output the test pat- Press the [Straight Mode] key and press the
tern (No.16). [COPY] key .
7. Fold the outputted paper in half in the paper feed 6. Select the paper size according to the item you
direction to check the misalignment with the sta- want to adjusted and press the Start button to out-
pling center position. put a test pattern (No. 16).
• Standard value: a = ± 3mm 7. Open the front door of the FS and pull out the
stacker.
Note
• If the length of the paper is longer than 239 mm
[1] in sub-scanning direction, the paper edge will
hanging out of the stacker. In that case, remove
a
the paper through the paper opening section
[2] before pulling out the stacker, and reload the
paper in the stacker.
8. Measure the gap between the paper in the stacker
fs503fs3011ca and the alignment plate.
Standard value: 0.1 to 1 mm
[1] Paper center [2] Stapling center position
9. When the value is not within the standard value,
8. When the value is not within the standard value,
press the [SERVICE] key.
press the [SERVICE] key.
10. "Stapling Paper Width Adj. screen"
Use the [Next] and [Back] key to select the paper
size you want to adjust.
471
470
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• Setting range: -20 (wide) to +20 (narrow) • Setting range: -20 (wide) to +20 (narrow)
1 step = 0.1 mm 1 step = 0.1 mm
12. Repeat steps 5 to 11 until the standard value can be 12. Repeat steps 5 to 11 until the standard value can be
obtained. obtained.
Note
• If the length of the paper is longer than 239 mm
in sub-scanning direction, the paper edge will
hanging out of the stacker. In that case, remove
the paper through the paper opening section
before pulling out the stacker, and reload the
paper in the stacker.
8. Measure the gap between the paper in the stacker
and the alignment plate.
Standard value: 0 ± 0.5 mm
9. When the value is not within the standard value,
press the [SERVICE] key.
10. "Stapling Paper Width Adj. screen"
Use the [Next] and [Back] key to select the paper
size you want to adjust.
2 471-1
471
470-1
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
7. Check to see if the bundle of papers is mis- 10.13.2 Multi folder (hole-punch) adjustment
aligned (a: a misalignment occurs when the Conduct the FD punch related adjustment.
paper width setting is larger than the paper
/1050e/1050eP
width) and if the bundle is curved (b: the curve A. Paper width adjustment
occurs when the paper width setting is smaller When a large mis-alignment is found with the position
than the paper width). of a punch hole, use a corresponding paper size to
• Standard value: a = ± 1.0 mm or less adjust the width of the alignment plate.
(16 sheets or less)
a = ± 1.5 mm or less (1) Procedure
(from 17 to 100 sheets)
1. Enter the service mode.
2. "Service mode menu screen"
a Press the [11 Finisher Adjustment] key.
3. A sub menu appears on the right side of the
screen.
Press the [02 Multi Folder (Punch) Adj.] key on
the sub menu.
b
4. "Multi Folder (Hole-Punch) adj. menu screen"
Press the [01 Paper Width Adjustment] key.
fs503fs3012c
5. "Paper Width Adjustment screen"
Press the [COPY] key.
8. When the value is not within the standard value, 6. Set paper you want to adjust in the tray, the
press the [SERVICE] key. number of copies is set to 10 and press the
9. "Stapling Paper Width Adj. screen" Start button.
Use the [Next] and [Back] key to select the
7. Check the diameter of the through-hole when
paper size you want to adjust.
the ejected paper is stacked.
10. Enter a value through the numeric keys and
No. of holes Standard value (mm)
press the [Set] key.
• Setting range:-20 (wide) to +20 (narrow) 2 & 4 holes φ 5.0 or larger
1 step = 0.1 mm 3 holes φ 6.5 or larger
11. Repeat steps 5 to 10 until the standard value 8. When the value is not within the standard value,
can be obtained. press the [SERVICE] key.
9. "Paper Width Adjustment screen"
Use the [Next] and [Back] key to select the
paper size you want to adjust.
10. Enter the set value through the numeric keys
and press the [Set] key.
• Setting range:-20 (narrow) to +20 (wide)
1 step = 0.1 mm
Note
• When the alignment plate is wider than an
appropriate position, the punch centering
is displaced, and when too narrow, the
punch holes are apt to disperse.
11. Repeat steps 5 to 10 until the standard value
can be obtained.
472
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(1) Procedure 1 step = 0.1 mm
1. Enter the service mode. 12. Repeat steps 5 to 11 until the standard value
can be obtained.
2. "Service mode menu screen"
Press the [11 Finisher Adjustment] key. 13. To configure other punch hole/paper size,
repeat steps 5 to 11.
3. A sub menu appears on the right side of the
screen.
Press the [02 Multi Folder (Punch) Adj.] key on
the sub menu.
4. "Multi Folder (Hole-Punch) adj. menu screen"
Press the [02 Hole-Punch Vertical Position
Adjustment] key.
5. "Punch Vertical Position Adj. screen"
Press the [COPY] key.
6. Set the paper of the paper size you want to
adjust in the tray, and select the number of
punch holes. Press the Start button to output
the test pattern (No.16).
7. Check the distance a from the outputted paper
leading edge to the punch holes center posi-
tion.
fs503fs3013c
473
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
474
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
b
NOTE
[1]
a • The position of the single fold is based on the
leading edge of paper and the position of the
[2]
double fold is based on the position of the
single fold. So, the dimension "a" and "b" in
a03uf3c019ca
the step 7 varies when either position of the
[1] Single fold [2] Double fold single fold and the double fold is changed.
Paper size Standard value (mm)
a± 1.5 b± 1.5 (1) Procedure
2 475
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
7. Check "a" and "b" on the outputted paper. D. Double parallel position adjustment
Adjust the folding position on the double parallel posi-
tion.
b Doppelparallel Falz
/1050e/1050eP
NOTE
• When adjusting both the single fold and the
a [1]
double fold, be sure to start with the double
[2]
fold.
a03uf3c020ca
• The position of the single fold is based on the
[1] Single fold [2] Double fold leading edge of paper and the position of the
Paper size Standard value (mm) double fold is based on the position of the
single fold. So, the dimension "b" in the step
a± 1.5 b± 1.5
7 varies when either position of the single fold
A3 282.0 144.0
and the double fold is changed.
B4 243.7 123.3
A4S 199.0 101.0 (1) Procedure
12 x 18 306.8 156.4
1. Enter the service mode.
11 x 17 289.9 147.9
2. "Service mode menu screen"
81/2 x 14 238.1 120.5
Press the [11 Finisher Adjustment] key.
81/2 x 11S 187.3 95.1
3. A sub menu appears on the right side of the
8K 262.0 134.0 screen.
Press the [03 Multi Folder (Fold) Adj.] key on the
8. When the value is not within the standard value,
sub menu.
press the [SERVICE] key.
4. "Multi Folder (Fold) adj. mode screen"
9. "Letter Fold-out Pos. Adjustment screen"
Press the [04 Double Parallel Position Adjust-
Use the [Next] and [Back] key to select the
ment] key.
paper size you want to adjust.
5. "Double Parallel Pos. Adj. screen"
10. Press the [Single Fold] key.
Press the [COPY] key.
11. Enter a value through the numeric keys and
6. Set the paper of the paper size you want to
press the [Set] key.
adjust in the tray. Press the Start button to out-
• Setting range: -50 to +50, 1 step = 0.1 mm
put the test pattern (No.16).
476 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
b NOTE
[1] • When adjusting both the single fold and the
double fold, be sure to start with the single
a
fold.
[2] • The position of the single fold is based on the
leading edge of paper and the position of the
a03uf3c021ca
double fold is based on the position of the
[1] Single fold [2] Double fold single fold. So, the dimension "b" in the step
Paper size Standard value (mm) 7 varies when either position of the single fold
and the double fold is changed.
a± 1.5 b± 1.5
A3 208.5 103.8
(1) Procedure
B4 180.5 89.8
A4S 147.0 73.0 1. Enter the service mode.
12 x 18 227.1 113.1 2. "Service mode menu screen"
Press the [11 Finisher Adjustment] key.
11 x 17 214.4 106.7
3. A sub menu appears on the right side of the
81/2 x 14 176.3 87.7
screen.
81/2 x 11S 138.2 68.6
Press the [03 Multi Folder (Fold) Adj.] key on the
8K 193.5 96.3
sub menu.
4. "Multi Folder (Fold) adj. mode screen"
8. When the value is not within the standard value,
Press the [05 Z-Fold Position Adjustment] key.
press the [SERVICE] key.
5. "Z-Fold Position Adjustment screen"
9. "Double Parallel Pos. Adj. screen"
Press the [COPY] key.
Use the [Next] and [Back] key to select the
paper size you want to adjust. 6. Set the paper of the paper size you want to
adjust in the tray. Press the Start button to out-
10. Press the [Single Fold] key.
put the test pattern (No.16).
11. Enter a value through the numeric keys and
press the [Set] key.
• Setting range: -50 to +50, 1 step = 0.1 mm
2 477
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
7. Check "a" and "b" on the outputted paper. 13. Enter a value through the numeric keys and
press the [Set] key.
• Setting range: -50 to +50, 1 step = 0.1 mm
b
/1050e/1050eP
[1] a
a03uf3c031ca
478 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
Altar Falz
1050e/1050eP
NOTE b
• When adjusting the single fold, the double a
fold and the triple fold, be sure to conduct the
[1]
single fold, the double fold and the triple fold
in this order. c [2]
• The position of the single fold is based on the [3]
leading edge of paper and the position of the
a03uf3c023ca
double fold is based on the position of the
single fold. So, the dimension "a" and "b" in [1] Single fold [2] Double fold [3] Triple fold
the step 7 varies when either position of the Paper size Standard value (mm)
single fold and the double fold is changed.
a± 1.5 b± 1.5 c± 1.5
A3 103.5 213.0 106.5
(1) Procedure
B4 89.5 185.0 92.5
1. Enter the service mode. A4S 72.8 151.5 75.8
2. "Service mode menu screen" 12 x 18 112.8 231.6 115.8
Press the [11 Finisher Adjustment] key. 11 x 17 106.5 218.9 109.5
3. A sub menu appears on the right side of the 8 /2 x 14
1
87.4 180.8 90.4
screen.
81/2 x 11S 68.4 142.7 71.4
Press the [03 Multi Folder (Fold) Adj.] key on the
8K 96.0 198.0 99.0
sub menu.
4. "Multi Folder (Fold) adj. menu screen" 8. When the value is not within the standard value,
Press the [06 Gate Position Adjustment] key. press the [SERVICE] key.
5. "Gate Position Adjustment screen" 9. "Gate Position Adjustment screen"
Press the [COPY] key. Use the [Next] and [Back] key to select the
6. Set the paper of the paper size you want to paper size you want to adjust.
adjust in the tray. Press the Start button to out- 10. Press the [Single Fold] key.
put the test pattern (No.16). 11. Enter a value through the numeric keys and
press the [Set] key.
• Setting range: -50 to +50, 1 step = 0.1 mm
2 479
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
15. Enter a value through the numeric keys and 10.13.5 Stacker adjustment
press the [Set] key. Conduct the LS related adjustments.
• Setting range: -50 to +50, 1 step = 0.1 mm LS-501 / 502
/1050e/1050eP
480
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
tray. A. Stapling center position adjustment
This adjusts the position of the leading edge stopper. Adjust the center position of the staple for the saddle
stitching mode.
(1) Procedure Broschürenfinisher SD-501
(1) Procedure
1. Enter the service mode.
2. "Service mode menu screen" 1. Enter the service mode.
Press the [11 Finisher Adjustment] key. 2. "Service mode menu screen"
3. A sub menu appears on the right side of the Press the [11 Finisher Adjustment] key.
screen. 3. A sub menu appears on the right side of the screen.
Press the [05 Stacker Adjustment] key on the Press the [06 Saddle Stitcher Adj.] key on the
sub menu. sub menu.
4. "Stacker Adjustment Mode Menu screen" 4. "Saddle Stitcher Adjustment Menu screen"
Press the [02 Paper Length Adjustment] key. Press the [01 Staple Center Adjustment] key.
5. "Paper Length Adjustment screen" 5. "Stapling Center Position Adjustment screen"
Press the [COPY] key. Press the [COPY] key.
6. Select A3 or 11 x 17 paper and press the start 6. Select A3 or 11 x 17 paper and press the start
button to output the test pattern (No. 16). button to output the test pattern (No. 16).
7. When a paper exit mis-alignment occurs, press 7. Check the misalignment between the staple-
the [SERVICE] key. center and the paper center.
8. "Paper Length Adjustment screen" • Standard value: a = ± 2 mm
Press the [Next] or [Back] key to select either
the stacker 1 or the stacker 2.
9. Enter a value through the numeric keys and
press the [Set] key.
• Setting range:-20 (narrow) to +20 (wide)
1 step: 0.1 mm [2] [1]
a
fs503fs3300c
1 481
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
adjustment.
10. Enter a value through the numeric keys and
This adjustment adjusts the position of the saddle
press the [Set] key.
stitching alignment plate.
Setting range:-20 (narrow) to +20 (wide)
1 step = 0.1 mm
NOTE
11. Repeat steps 5 to 10 until the standard value
• Make sure that the folding skew adjustment
can be obtained.
of the mechanical adjustment has been com-
pleted.
C. Staple pitch adjustment
(1) Procedure Adjust the stapling interval for the saddle stitching
mode.
1. Enter the service mode.
2. "Service mode menu screen"
(1) Procedure
Press the [11 Finisher Adjustment] key.
3. A sub menu appears on the right side of the 1. Enter the service mode.
screen. 2. "Service mode menu screen"
Press the [06 Saddle Stitcher Adj.] key on the Press the [11 Finisher Adjustment] key.
sub menu. 3. A sub menu appears on the right side of the screen.
4. "Saddle Stitcher Adjustment Menu screen" Press the [06 Saddle Stitcher Adj.] key on the
Press the [02 Stapling Paper Width Adjust- sub menu.
ment] key. 4. "Saddle Stitcher Adjustment Menu screen"
5. "Staple Paper Width Adj. screen" Press the [03 Staple Pitch Adjustment] key.
Press the [COPY] key. 5. "Staple Pitch Adjustment screen"
6. Set the paper of the paper size you want to Press the [COPY] key.
adjust. Press the Start button to output the test 6. Set the paper of the paper size you want to
pattern (No. 16). adjust. Press the Start button to output the test
7. Check to see if the bundle of papers is mis- pattern (No. 16).
aligned (a: a misalignment occurs when the 7. Check the interval "a" between the staples
paper width setting is larger than the paper against the paper size "b."
width) and if the bundle is curved (b: the curve • Standard value: a = (b/2) ± 2 mm
occurs when the paper width setting is smaller
than the paper width).
• Standard value a: 1.0 mm or less
a
b
b
fs503fs3011c
fs503fs3012c
8. When the value is not within the standard value,
press the [SERVICE] key.
8. When the value is not within the standard value,
press the [SERVICE] key.
482 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
10. Enter a value through the numeric keys and
press the [Set] key. a
• Setting range:-20 (narrow) to +20 (wide)
1 step = 1 mm
• Setting range is restricted by the paper size.
Minimum value is determined based on the sta- fs503fs3014c
pler movable range and the maximum value is
8. When the value is not within the standard value,
determined so that the saddle stitching align-
press the [SERVICE] key.
ment plate and stapler do not interfere with
each other. 9. "Folding Position Adjustment screen"
B5S: Setting is not possible (fixed to 91 mm) Use the [Next] and [Back] key to select the
B4: -20 to +20 mm (108.5 to 148.5 mm) paper size you want to adjust.
A4S: -14 to +14 mm (91 to 119 mm) 10. Enter a value through the numeric keys and
A3: -20 to +16.5 mm (128.5 to 165 mm) press the [Set] key.
81/2 x 14, 81/2 x 11S: -16.95 to +16.95 mm Setting range: -20 to +20
(91 to 124.9 mm) 1 step = 0.1 mm
11 x 17, 8 /2 x 11: -20 to +20 mm
1 • In case of the misalignment given in the step 7,
(119.7 to 159.7 mm) enter a set value on the positive side.
11. Repeat steps 5 to 10 until the standard value 11. Repeat steps 5 to 10 until the standard value
can be obtained. can be obtained.
6. Set the paper of the paper size you want to 1. Enter the service mode.
adjust. Press the Start button to output the test
2. "Service mode menu screen"
pattern (No. 16).
Press the [11 Finisher Adjustment] key.
3. A sub menu appears on the right side of the
screen.
Press the [06 Saddle Stitcher Adj.] key on the
sub menu.
2 483
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
484 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
1 step = 0.1mm 1 step = 0.1mm
11. Repeat steps 5 to 10 until the standard value 11. Repeat steps 5 to 10 until the standard value
can be obtained. can be obtained.
G. Trimming adjustment
When there is misalignment in the trimmed fore-edge
or the trimming is too much, conduct this adjustment.
(1) Procedure
Note
• Trimming distance less than 2mm may
cause trimming fault.
fs503fs3301c
1 485
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
the cover paper. • Setting range: -128 (reduces the trimming amount) to
Klebebinder PB-501 +127 (enlarges the trimming amount)
NOTE 1 step = 0.1mm
• In order to align the leading edges on the left
11. Repeat the steps 5 to 10 until an appropriate
and right covers, perform the adjustments in
value is obtained.
the order shown below:
1. B Cover lead edge adjustment
2. A Cover trimming adjustment B. Cover lead edge adjustment
Sets the length that the left side of cover paper
(1) Procedure exceeds the length (width) of inside pages.
486 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(1) Procedure
binding.
9. Check that the width of the left cover paper is 1. Enter the service mode.
longer than that of the inside pages by speci- 2. "Service mode menu screen"
fied amount. Press the [11 Finisher Adjustment] key.
3. A sub menu appears on the right side of the
[3] [4] screen.
Press the [07 Perfect Binder Adjustment] key
[5]
on the sub menu.
[1] 4. "Perfect Binder adjustment mode menu
screen"
Press the [03 Spine Corner forming Position
[2] 1050fs3358c
Adj.] key.
[1] Inside pages [2] Right cover paper 5. "Spine Corner forming Up/Down Adj. screen"
[3] Left cover paper [4] Length differential Press the [COPY] key.
[5] Edge of the left cover paper 6. Select the paper type and press the start but-
10. To change the width of the left cover paper, ton to make test prints and carry out perfect
press the [SERVICE] key. binding.
11. "Cover Lead Edge Adj. screen" 7. Check that the corner edges of the cover paper
Enter a value through the numeric keys and are created uniformly in the main scan direc-
press the [Set] key. tion.
• Setting range:-128 (short) to +127 (long)
1 step = 0.1mm [4]
12. Repeat the steps 5 to 11 until an appropriate
value is obtained. [1]
[2]
[3]
1050fs3359c
2 487
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
D. Pasting start postion adjustment 9. Check that the glue applying start position to
Adjusts the start position for applying glue to inside the inside pages is appropriate.
pages.
/1050e/1050eP
[3]
(1) Procedure
Note
• Above paper sizes are book (the inside
pages) finished sizes.
7. Press the [COPY] key.
8. Select the paper type and press the start but-
ton to make test prints and carry out perfect
binding.
488 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(1) Procedure
[3]
1. Enter the service mode.
2. "Service mode menu screen"
Press the [11 Finisher Adjustment] key.
3. A sub menu appears on the right side of the
screen. [1]
Press the [07 Perfect Binder Adjustment] key
on the sub menu.
4. "Perfect Binder adjustment mode menu screen" [2] 1050fs3361c
Note
• Above paper sizes are book (the inside
pages) finished sizes.
7. Press the [COPY] key.
8. Select the paper type and press the start but-
ton to make test prints and carry out perfect
binding.
2 489
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
F. Paste formation finish position adjustment 10. "Paste Formation Finish Adj. screen"
Adjusts the finish position of the process to make a Enter a value through the numeric keys and
uniform layer of glue applied on the inside pages press the [Set] key.
/1050e/1050eP
Note
• Above paper sizes are book (the inside
pages) finished sizes.
6. Press the [COPY] key.
7. Select the paper type and press the start but-
ton to make test prints and carry out perfect
binding.
8. Check that the finish position of the process to
make a uniform layer of glue on the inside
pages spine is appropriate.
9. When adjusting the the finish position of the
process to make a uniform layer of glue,
press the [SERVICE] key.
490 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
temperature sensor/Up (TH2), the glue tank tempera- Setting range: 10 to 200 °C
ture sensor/Md (TH3), and the glue tank temperature Default: 132 °C
sensor/Lw (TH4) provided in the glue tank. • Melt Tank - Mid
Setting range: 140 to 200 °C
(1) Procedure Default: 145 °C
• Melt Tank - Low
1. Enter the service mode.
Setting range: 140 to 200°C
2. "Service mode menu screen"
Default: 185 °C
Press the [11 Finisher Adjustment] key.
• Pasting Roller
3. A sub menu appears on the right side of the Setting range: 140 to 200 °C
screen. Default: 165 °C
Press the [07 Perfect Binder Adjustment] key
11. Repeat the steps 5 to 10 until an appropriate
on the sub menu.
value is obtained.
4. "Perfect Binder adjustment mode menu
screen"
Press the [07 Temperature Adjustment] key.
5. "Temperature Adjustment screen"
Press the [COPY] key.
6. Select the paper type and press the start but-
ton to make test prints and carry out perfect
binding.
7. Check that the glue applied has dried appropri-
ately.
8. To adjust the dryness of the glue, press the
[SERVICE] key.
9. "Temperature Adjustment screen"
Press the [NEXT] or the [Back] key to select the
option of which the temperature is set.
The following options are provided.
Melt Tank - Top
Melt Tank - Mid
Melt Tank - Low
Pasting Roller
2 491
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note Note
• Above paper sizes are book (the inside • Above paper sizes are book (the inside
pages) finished sizes. pages) finished sizes.
6. "Sub Compile CD Width Adj. screen" 6. "Clamp CD Width Adj. screen"
Enter a value through the numeric keys and press Enter a value through the numeric keys and press
the [Set] key. the [Set] key.
• Setting range:-20 (wider) to +20 (narrower) • Setting range:-20 (wider) to +20 (narrower)
1 step = 0.1mm 1 step = 0.1mm
7. Create multiple books in normal copy mode, 7. Create multiple books in normal copy mode,
and check the alignment of the second and and check the alignment of the second and
later book. Change set value set in Step 5 until later book. Change set value set in Step 5 until
an properly aligned book is created. an properly aligned book is created.
492 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
(1) Procedure (1) Procedure
2 493
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• If the setting is too wide, pages are mis-
placed in sub-scanning direction.
• If the setting is too narrow, mark of the FD
alignment plate may appear.
494 2
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
• The use of the security strengthen mode in
NOTE
the machine manager setting in the utility
• The stacker adjustments cannot recall.
mode is limited only when the manager
authentication is set to "Authentication On."
A. Procedure
495
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
496
Field Service Ver3.0 Nov.2006 10. SERVICE MODE
1050e/1050eP
NOTE Formatting enables you to secure space/delete inter-
• The selection of the [CE Password Setting] nal data.
key is limited only when the CE authentica-
tion setting is set to "Authentication On." (1) Procedure
• Do not use anything easily guessed by others
1. Enter the service mode.
such as your name, birthday.
• CE should not inform other people of the 2. "Service mode menu screen"
password. Press the [14 IP HDD Format] key.
3. A sub menu appears on the right side of the
(1) Procedure screen.
Press the [01 IP HDD Format] key on the sub
1. Enter the service mode. menu.
2. "Service mode menu screen" 4. "IP HDD Format screen"
Press the [13 CE Setting] key. HDD format includes the following five items.
3. A sub menu appears on the right side of the [ALL]
screen. [Document]
Press the [02 CE Password Setting] key. [Parameter]
4. "CE Password Setting screen" [Font]
Enter an 8-digit password with alphanumeric [Spool]
keys. 5. Press the item you want to format.
Default is "92729272." 6. "Format confirmation screen"
5. Press the [OK] key to register data. The message "Execute Format Yes/No?"
Press the [Cancel] key to cancel the setting you appears.
entered. Press the [Yes] key.
NOTE
• Be sure to output the settings information list
before formatting parameters.
497
10. SERVICE MODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
• [Font]
Formats the font data storage area.
Conduct this when deleting downloaded exter-
/1050e/1050eP
NOTE
• By formatting, all downloaded external fonts
are deleted.
• [Spool]
Formats the spool area.
There is no need to format this area alone.
498
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
11.1.1 Tray centering adjustment
This adjustment is made when the mis-centering of paper varies each paper supplied from the trays /1 and /2.
The mis-centering is automatically adjusted in the image processing unit, and this adjustment is made only when
a mis-centering exceeding the range of auto correction (±5 mm) occurs.
1050fs3028c
499
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Affected by the paper type and the operating environment (the no feed is likely in the low temper-
ature environment and the double feed is likely in the high temperature environment).
• Excess adjustment may reverse the symptom.
Note
• The separation pressure is strengthened
when the lever is moved to the direction [2]
and is weakened when the lever is moved to
the direction [3].
Weak: a double feed jam is improved.
[2] [1] [3] Strong: a no feed jam is improved.
Reference
• The spring load changes 10% as the spring is
moved one step.
1050fs3029c
500
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
1. Pull out the paper feed tray.
[2] [1]
2. In the pick-up roller section [1], put paper feed
assist plate [3] on the paper feed assist plate
holder [2], and fix them with accompanying screw
(M3 x 8 mm) [4].
3. Set the tray.
4. Perform copying/printing to check whether the no
feed or the double feed occurs or not.
Note
• The maximum number of the paper feed
assist plates that can be attached is 4 plates.
For the number of plates to be attached, see
[4] [3] [4] chapter V "5. Paper setting."
• The paper feed assist plate is approx. 10g
each.
1050fs3030c
501
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
• A no feed jam in which a thick paper is stuck on the entrance guide (a metallic guide plate near the separa-
tion roller)
• A double feed jam is not improved by the separation pressure adjustment
Note
• On performing the pick-up roller height adjustment, the paper feed pick-up amount is changed. Be
sure to confirm the paper feed pick-up amount in the paper feed pick-up amount adjustment.
(See P.505)
1050fs3031c
502
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
6. Remove 2 screws [1] to remove the paper feed
cover [2].
[2] 1050fs3032c
[4]
1050fs3033c
503
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Place the upper limit sensor placing plate [1]
horizontally.
[4] [1]
Adjustment standard
• Lifting the upper limit sensor position lowers
the height of the pick-up roller [5]. (The differ-
ence of elevation [7] between the paper feed
roller [6] and the pick-up roller [5] becomes
larger.)
• Lowering the upper limit sensor position lifts
the height of the pick-up roller [5]. (The differ-
ence of elevation [7] between the paper feed
[3] roller [6] and the pick-up roller [5] becomes
[5] [6] smaller.)
• In case a no feed occurred, lower the upper
limit sensor.
• In case a double feed occurred, lift the upper
limit sensor.
[7]
12. Place the pick-up roller section, and replace the
stopper of step 4 to the original position.
Note
1050fs3034c
• If you set the tray without placing the pick-up
roller, the paper lift does not stop at the upper
limit, thus damaging the tray. Be sure to place
the roller.
Note
• After the adjustment, be sure to replace the
stopper of the release lever to the original
position.
504
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
1. Pull out the paper feed tray.
[2] [3] [1]
2. If any paper remaining, remove it.
3. Loosen a screw [1].
4. With the release lever [2] placed at its original
position, hold the stopper [3] and tighten the
screw [1] to fix the stopper.
1050fs3035c
5. Set the tray. Confirm that the paper lift finished its
[1]
elevation to the top by hearing the sound of the
paper lift motor. Pull out the tray again.
6. Remove 2 screws [1] to remove the paper feed
cover [2].
[2] 1050fs3036c
505
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Before loosening the screw [5], record the
position of the pick-up solenoid [1] with the
marking line [6].
Note
• After the adjustment, be sure to replace the
stopper of the release lever to the original
position.
506
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
1. Pull out the paper feed tray.
[2] [3] [1]
2. If any paper remaining, remove it.
3. Loosen a screw [1].
4. With the release lever [2] placed at its original
position, hold the stopper [3] and tighten the
screw [1] to fix the stopper.
1050fs3038c
5. Set the tray. Confirm that the paper lift finished its
[1] [2]
elevation to the top by hearing the sound of the
paper lift motor. Pull out the tray again.
6. Remove 2 screws [2] of the stopper of the rails [1]
on the right and left side. Pull out the tray.
1050fs3039c
507
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
• Removing the screws [1] and [2] causes the
tray front cover [3] to fall. Support the cover
not to drop.
[1]
Note
• Be sure to connect the connector as you
place it. Otherwise, all trays in the main body
become unable to be pulled out.
[2]
[3]
[4]
1050fs3040c
508
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
11. Remove the screw [3], and place them temporarily
in the slotted screw hole [4].
12. While holding the pulley placing plate being
placed with the screw [5], loosen the screw [5] to
adjust the skewed paper lift plate [7] with the
marking line [6].
13. Confirm that the paper lift plate is horizontal, and
fix the screw [5] and [8].
14. Pull down the pick-up roller [1].
15. Place the tray front cover.
16. Insert a paper, and set the tray.
17. Perform copying/printing to confirm that the no
jam occurs, and that papers are properly fed.
18. Reinstall the above parts following the removal
steps in reverse.
[2] 1050fs3041c
509
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Info HJG:
Justage der Passergenauigkeit ist ein
Zusammenspiel der Position der
[3] <Druckeinheit> und der Einstellung
der<Registrationseinheit> !
Achtung: Vor dem lösen der Druckeinheit,
vorher Gerät ausschalten !
[2] 1050fs3070c
510 1
Field Service Ver3.0 Nov.2006 11. MECHANICAL ADJUSTMENT
1050e/1050eP
This adjustment enables you to up/down the pre-transfer roller nip pressure.
Perform this adjustment when a transfer jitter occurred. For more information on how to perform this adjust-
ment, see "12.4 Transfer jitter adjustment".
Note
• To restore the previous nip pressure, twist
clockwise the conveyance roller /T axis until
the axis stopper is locked.
1 511
11. MECHANICAL ADJUSTMENT Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Note
[1] [7]
• To restore the standard nip pressure, place
the spring /Fr [2], /Rr [3].
• Removing/placing the spring with the nip
pressure up tends to stretch the spring. Thus,
remove/place the spring with the standard nip
pressure. If tension of the spring /Fr and /Rr
differs, a transfer misalignment occurs. When
restoring the standard nip pressure, in case
the spring was stretched, do not use it and
replace it with a new one.
• In case the spring /Fr [2], /Rr [3] are not easily
removed from the hook hole /Lw [5], remove it
from the hook hole /Up [4] first. Then, while
holding the spring not to drop, twist counter-
clockwise (nip pressure up) the conveyance
roller /T axis [1] and rotate the cam [6] to
make a gap, thus making it easy to remove
the spring.
• Be careful not to drop the spring. Put a paper
over the ADU section [7] so that the spring
does not fall inside the machine.
512
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
for POD With the registration roller paper skew adjust-
Info HJG: Justage durch Kunden unter Button <System> !
ment in the mechanical adjustment, adjust the
This section describes how to make adjustments to
skew of the sub scan direction on both side to
improve image quality (The front and back registra-
be parallel to each other.
tion, image density, transfer jitter) and paper feeding
so as to satisfy the needs of customers (especially
POD customers) who demand even higher quality of
image and feeding than the factory settings.
becomes smaller than the back side. [1] Front [2] Back
• The shrinkage ratio in passing the fusing section is
different depending on the paper type, paper
brand, temperature/humidity of a paper storage
location. To adjust misalignment due to these fac-
tors, use the front and back adjustment in the user
mode, selecting [MACHINE] - [Paper Set] - [Regis-
ter Type/Weight]. To adjust misalignment due to
individual difference of each tray, select the tray
you want to adjust in the user mode, selecting
[MACHINE] - [Paper Set] - [Tray Setting]. Then,
select [Change] - [Both Sides Adj.] to make an
adjustment.
1 513
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
2. Adjust distortion in the main scan direction on both sides. 3. Use the service mode to adjust various image
Remove the photo conductor cover and open the timing in the front side of printer system.
intermediate toner hopper. Mark current position of
/1050e/1050eP
[1]
[1]
[2] 1050fs3043c
[4]
[5]
1050fs3042c
514
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
and [Printer Horizontal Adjustment <SIDE2>] to Setting]. Then, select [Change] - [Both Sides
align magnification of the back side to the front Adj.] to make adjustment. Use the Image Shift
side. function to align the centering of the back side
on the figure A to the front side.
Note
• With the [Printer Centering Adjustment] in
the service mode, there is no adjustment
for individual tray.
• Since a test pattern cannot be output in the
user mode, output an image from a PC so
you can confirm the image centering or use
[Test Pattern Output Mode] in Service
mode.
• The [Tray Setting] you set in step 5 is an
individual adjustment, in which the updated
settings are not applied to the registered
paper type. Thus, to change the registered
paper type, select the paper name key you
want to adjust in [MACHINE] - [Paper Set] -
[1] [Register Type/Weight]. Make the adjust-
[2] ment with the Image Shift function of [Both
1050fs3044c
Sides Adj.].
[1] Front [2] Back
[1]
[2] 1050fs3045c
515
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12.2.2 The front and back registration (scan- 5. Adjust the original skew.
ner) Remove the original stopper plate /Rr, and
A. Procedure mark the current position of the adjustment
/1050e/1050eP
[1]
[2] 1050fs3046c
[1]
[2] [1]
1050fs3047c
[2] 1050fs3048c
[1] Front [2] Back
[1] Front [2] Back
516
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
adjustment. the figure A to the front side.
3. Align the leading edge timing of both sides. [1] Front [2] Back
Use [ADF restart timing adjustment(SIDE2)] in 5. Adjust the ADF paper skew.
the service mode. Use the cross on the figure A With the ADF paper skew adjustment in the
to align the leading edge timing of the back mechanical adjustment, adjust the skew on the
side to the front side. front and back side.
[1]
[2] 1050fs3049c
[1]
[2] 1050fs3051c
517
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
6. Perform steps 3 and 4 to adjust the misalign- 3. Press the name key of paper you want to
ments of timing and centering caused by the change, or press [Next] key to register paper
ADF paper skew adjustment. newly.
/1050e/1050eP
NOTE
• Check to see if the front and back registra-
tions in 12.2.1 to 12.2.3 are completed.
2. Press the [Register Type/Weight] key. 5. Press the [Both Sides Adj.] key, and adjust the
front and back registration.
518
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
paper as described in 12.2.4, an adjustment may be
required depending on the number of tray in which
paper is fed, the storage condition (temperature and
humidity) of paper and the temperature and humidity
in the room, etc.
This adjustment describes the method for fine adjust-
ment of each tray to the front and back adjustment of
the paper brand setting described in 12.2.4.
NOTE
• Check to see if the front and back registra-
tions in 12.2.1 to 12.2.4 are completed.
4. Press the [Both Sides Adj.] key.
2 519
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
5. Register the front and back of the paper. 12.3 Image density adjustment
There are two modes for the registration, auto-
matic (adjustment) and manual (adjustment). 12.3.1 Darken image density
/1050e/1050eP
• Manual registration (adjustment) Print industry customers may demand image settings
with dark image density in the shadow area such as
the offset printing.
This section describes how to adjust the shadow
area (max. density) to make its image density darker.
If the adjustment to make image density darker is not
performed properly, toner spillage or image back-
ground occurs. By this procedure, the density can be
adjusted more safely, minimizing occurrences of
these problems. However, perform this adjustment
only when necessary.
Related adjustments are as follows.
• Utility mode
1) Image density selection
This setting changes the charger voltage and the
• Automatic registration (adjustment)
developing bias.
Press [Chart Adjustment] to execute the auto-
• Service mode
matic registration (adjustment).
1) DIPSW23-2, 3, 4 toner density of developer
This setting changes the developing roller rota-
tion and toner density, thus changing the toner
density of developer without changing image
density.
2) DIPSW27-2, 3 image density selection (toner con-
trol patch density)
This setting changes the developing bias for cre-
ating the toner control patch formed on the drum
to determine toner density, thus changing toner
density of developer to change image density.
A. Procedure
6. When adjusting another tray, repeat the steps 3
to 5. 1. With the image density selection of the density
setting in the utility mode, set Darker [+1].
2. In the test pattern output mode, output the test
pattern No.11 to check image density.
3. When image density is insufficient, set the
image density selection "approx. 0.5% up" in
the DIPSW27-2, 3.
4. With the DIPSW23-2, 3, 4 toner density of
developer, set "approx. 0.5% down" or
"approx. 1.0% down" to prevent from image
background and toner spillage.
520 2
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
Note
2. Output test pattern No.11 in the test pattern
• The settings in steps 3 and 4 change the
output mode to confirm image density.
toner density of developer. Thus, image
density does not change without making 3. When image density is insufficient, repeat steps
prints. 1 and 2 until "-5."
8. With DIPSW23-2, 3, 4 toner density of devel- 6. When image density is insufficient, set as "light-
est" in the DIPSW5-2, 3.
oper, set "approx. 1.5% down."
9. Output 500 prints of the test pattern No.11 in 7. Output test pattern No.11 in the test pattern
output mode to confirm image density.
the test pattern output mode.
10. Confirm image density.
521
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
522
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
decreased and the paper speed became
faster momentarily.
Note
Possible with thick papers 200 g/m2 or
• If the nip pressure is strengthened it is pos-
heavier.
sible that transfer jitter 40 mm from the
trailing edge may occur. In this instance
(6) Random occurrence
select whichever image is best. (before
1) Transfer jitter that occurs when the leading
pressure increase or after)
edge of paper touches the conveyance sec-
• If transfer jitter occurs at around 140 mm
tion. Main causes are as follows.
from the trailing edge, it may be impossible
• Speed change of the conveyance belt itself
to determine if the jitter is caused by the
• Speed difference between the registration roller
registration roller (145 mm) or by the fusing
and the conveyance belt
unit (138 mm). In this instance cut 20 mm
• Rough paper movement while it passes through
off the trailing edge of an A3 sheet and
the conveyance belt
print a test pattern to the cut paper. If the
• Shock because of the paper leading edge touch-
position of the jitter changes in relation to
ing the conveyance belt
the leading edge the cause can be deter-
mined to be the registration roller.
C. Procedure
(1) Approx. 250 mm from the trailing edge 2. Remove 2 screws [2] to remove 2 suction cov-
ers [1] at the lower side of the conveyance belt
1. With the [Printer Regist Loop Adjustment] in the on both sides of the conveyance section so as
service mode, reduce loop amount. to improve the conveyance suction ability.
523
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
3. Reverse the paper set direction in the tray. Set (5) Approx. 40 mm from the trailing edge
paper so that the curling direction of paper
1. Remove 2 pressure springs of the pre-transfer
becomes concave on the conveyance section.
roller.
/1050e/1050eP
Note
• If the transfer suction ability is increased it
is possible that transfer jitter may occur
145 mm from the trailing edge. Select
whichever image is best. (before adjust-
ment or after)
3. Reverse the paper set direction in the tray. Set
paper so that the curling direction of paper
become concave on the conveyance section.
When the curling is convex, the leading edge of
paper hits against the entrance guide plate and
this may be apt to cause a transfer jitter.
524 1
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
address, the logo, etc. on offset printed paper. • Set paper on which overlay printing has been
When performing overlay printing, take notice the fol- made.
lowing description. • Set the type of paper to [Coated B].
• Set the air assist setting to [On].
Reference:
• The surface of coated paper is applied with a coat- NOTE
ing agent and so it takes more time for the ink of • Registration of back and front sides must be
offset printing to dry. Therefore, to prevent block- checked every day before starting printing.
ing (back transfer), the entire surface of paper is
applied with powder. 2. Make the following settings in the service mode.
The powder drastically reduces the conveyance • Set software DIPSW26-4 to 1. (Sets tray /4 forced
forces of the pick-up roller and the paper feed separation clutch control to the operation at all times.)
roller, and this may be apt to cause a no feed jam • When performing overlay printing on both front
or a double feed jam. and back sides of paper weighing 91 g/m2 or
lighter, set the software DIPSW6-2 to "1". (this dis-
NOTE ables the transfer assist control.)
• Before overlay printing, be sure to take note • Set the DIPSW2-4/5 to "1". (sets the cleaning
of following. cycle of the charging corona to every 5,000 prints )
a) Be sure to install the PP-701 (urethane • When using paper other than coated paper for
roller) overlay printing, make the paper type setting to
b) We recommend use of RC-501 for the other than "coated B" and set the software DIPSW
overlay printing. corresponds to the selected paper tray to "1".
c) Apply as little powder as possible when tray 1: DIPSW39-0
offset printing. tray 2: DIPSW39-1
d) Get paper loosened sufficiently before tray 3: DIPSW39-2
setting it in the tray /4. tray 4: DIPSW39-3
e) Adjust paper condition with the same tray 5: DIPSW39-4
environments (temperature and humidity)
as those for the main body. When left in a NOTE
high humidity environment, paper strongly • When the above mentioned DIPSW is set to
adhere to each other making them unable "1", paper feed control will be the same as
to feed. that of [Coated paper B]. This improves the
endurance of the urethane roller, however,
• A paper centering error is likely to occur due double feed may occur at frequent intervals.
to contamination of the centering sensor • The above mentioned DIPSW will not work
(PS54) with powder. Clean the sensor if the when [Coated paper A] or [Paper weight 92 g/
error occurs or before starting overlay print- m2] or more is selected for the paper setting.
ing.
• Registration of paper must be checked every 3. Install the paper feed assist plate.
30,000 prints. (See "5.3 Adjusting the pick-up roller pressure"
in the Field Service for the PF-701.)
NOTE
• The number of paper feed assist plates varies
according to the paper weight.
130 g/m2 or less → None
131 g/m2 or more → 4 pcs.
2 525
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
paper are appropriate. Otherwise air assist is not con- of the paper feed assist fan /Fr and /Rr and the
ducted properly and this may result in a jam occur- upper surface of paper [3].
rence. • Standard value a: within 4.5 ± 2.5 mm
(1) Procedure When the value is not within the standard, con-
duct step 7 and succeeding steps.
1. Pull out tray /4 and set about 10 sheets of
coated paper that have been printed.
2. Push in the release lever [1], insert the screw [2]
into the hole [3] to fix the release lever, and then
set the tray /4.
[2]
[1] [2]
[3]
[3]
[1] 1050fs3059c
526
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
1050fs3060c
1050fs3062c
Put the underlays (included in the PP package)
[1] under the lower side of the stacked paper.
Put the underlays (included in the PP package)
Note [1] under the both sides of the stacked paper.
• To prevent air from blowing upon the pad
when the remaining paper gets low, place Note
the pad to the right side of the air supply • To prevent air from blowing upon the pad
opening position [2]. when the remaining paper gets low, place
the pad to the right side of the air supply
[2] [1] opening position [2].
[2] [1]
1050fs3351c
1050fs3352c
2 527
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
4) When there is a concave curling found with 9. Remove the PF right cover.
paper: (See chapter II "2.2.1 A. Removal/reinstallation of the
right cover" in the Field service for the PF-701.)
/1050e/1050eP
Note
• To prevent air from blowing upon the pad
when the remaining paper gets low, place [1]
the pad to the right side of the air supply
opening position [2], hitting it against the
paper rear guide plate [3].
In the case of a concave curling, it is nor-
mally possible to adjust curling by placing a
pad at the center position 40 mm away
from the front and rear paper guides.
[2] [1]
1050fs3066c
528 2
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
pressure adjustment."
14. Reinstall the above parts following the removal
steps in reverse.
Note
• Be sure to release the release lever that
has been fixed at the step 2.
(1) Procedure
ice.)
• J14-01 with thick paper (Paper is not conveyed
to the separation roller due to paper being una-
Note
ble to get over the entrance guide plate.)
• 4 sheets of paper feed assist plate are nor-
Up the pick-up roller height. (Down the sensor
mally used. However, when a no feed con-
position. 2 mm as a tentative)
dition recurs, it is possible to use up to 8
(See "5.2 Adjusting the pick-up roller height" in
sheets.
PF-701 Field Service.)
• J14-01 (paper bumps against the both • J14-01 (Jam with a crushed leading edge of
sides [2] of the entrance guide plate [1] and paper)
cannot go over the entrance guide plate Increase the separation pressure.
[1].) Put the underlays (included in the PP (See "5.4 Adjusting the separation pressure" in
package) [3] on the bottom of the tray PF-701 Field Service.)
locating them directory below [4] the both • J14-02 (No feed occurs before the pre-registra-
edges [2] of the entrance guide plate [1]. tion roller.)
Increase the separation pressure.
• Be sure to set the underlays [3] so that (See "5.4 Adjusting the separation pressure" in
those top edges are not contacted with the PF-701 Field Service.)
surface [5] of the tray, otherwise they may
• J17-02 (Double feed)
interfere with the paper lift plate operation.
Down the pick-up roller height. (Up the sensor
• Put the underlays [3] avoiding the paper
position. 2 mm as a tentative)
empty sensor [6].
(See "5.2 Adjusting the pick-up roller height" in
the Field Service for the PF-701.)
2 529
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
12.6 User setting of each paper 12.7 Settings for feeding carbon-
brand less paper
/1050e/1050eP
For the user setting method for paper which is com- When using carbonless paper (thin paper), take the
monly used in the POD market, see "19. PAPER SET- following measures.
TING", by paper brand.
This document shows the optimum set values for Reference
paper brands tested by KMBT. • The carbonless paper adheres to the conveyance
However, it does not assure the same image quality belt under suction while it is conveyed by the belt.
and paper feed ability as the paper specified by This makes the paper reading edge to be flipped
KMBT. Only the basic performance under usual envi- up when it comes to the fusing section, and the
ronment (temperature and humidity) has been tested reading edge is rubbed against the fusing entrance
and confirmed. guide causing soiled on the printed side.
Information on other brand of paper will be also pro-
vided when the test is finished, by updating the docu- NOTE
ment. • When feeding carbonless paper, take the fol-
lowing countermeasures.
a) When printing on carbonless middle
sheets, 50mm width of the sheet leading
edge reacts by the pressure and changes
in color. If this cannot be allowed, use
middle sheets 60 mm longer in main scan
direction, and 20 mm longer in sub scan
direction to trim off the discolored portion.
b) Set carbonless paper in SEF position (the
narrower side of paper comes to the
paper feed roller side).
c) Set the paper so that the paper curls con-
vexly in the conveyance section.
d) Allowable curl amount is less than 3 mm.
When using paper curled more than 3 mm,
use the overlays included in the PP-701
package to correct the curl.
e) Only [Simplex mode] is acceptable for
carbonless paper.
A. Preparation
1. Configure the settings below in user mode.
• Set the paper type to [Coated A].
• Set the air-blow setting to [ON].
• Set the output setting to [Face-down].
530 2
Field Service Ver3.0 Nov.2006 12. ADJUSTMENT FOR POD
1050e/1050eP
suction holes [2] can be seen.
2 531
12. ADJUSTMENT FOR POD Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
/1050e/1050eP
Blank page
532
Field Service Ver3.0 Nov.2006 13. JAM CODE
1050e/1050eP
13. JAM CODE
13.1 Jam code list
Classifi- Jam Cause Resulting Correction
cation code operation
Tray 1 J11-01 The paper feed sensor /1 (PS7) does If there is a sheet Pull out tray /1 and
During operation
not turn ON within a specified period of of paper being remove jammed paper if
time after the paper feed clutch /1 (CL4) printed when a any.
turns ON. jam occurs, the
J11-02 The pre-registration sensor /1 (PS17) main body com- Open tray /1 and the
does not turn ON within a specified pletes the paper main body vertical con-
period of time after the paper feed exit before stop- veyance door, and
clutch /1 (CL4) turns ON. ping operations. remove jammed paper if
J11-03 The vertical conveyance sensor /1 any.
(PS19) does not turn ON within a speci-
fied period of time after the pre-registra-
tion sensor /1 (PS17) turns ON.
J11-04 When the trailing edge of paper is pass- After completion
ing through the vertical conveyance of the exit of the
sensor /1 (PS19), the pre-registration preceding paper,
sensor /1 (PS17) is turned ON by the the main body
succeeding paper. stops operations.
J11-05 The vertical conveyance sensor /1 — Open the main body ver-
When idling
not turn ON within a specified period of of paper being remove jammed paper if
time after the paper feed clutch /2 (CL6) printed when a any.
turns ON. jam occurs, the
J12-02 The pre-registration sensor /2 (PS18) main body com- Open tray /2 and the
does not turn ON within a specified pletes the paper main body vertical con-
period of time after the paper feed- exit before stop- veyance door, and
clutch /2 (CL6) turns ON. ping operations. remove jammed paper if
J12-03 The vertical conveyance sensor /3 any.
(PS21) does not turn ON within a speci-
fied period of time after the pre-registra-
tion sensor /2 (PS18) turns ON.
2 533
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
ing through the vertical conveyance of the exit of the main body vertical con-
sensor /3 (PS21), the pre-registration preceding paper, veyance door, and
sensor /2 (PS18) is turned ON by the the main body remove jammed paper if
succeeding paper. stops operations. any.
J12-05 The vertical conveyance sensor /3 — Open the main body ver-
When idling
(PF) not turn ON within a specified period of of paper being remove jammed paper if
time after the pick-up clutch /1 (CL6) printed when a any.
turns ON. jam occurs, the
J13-02 The pre-registration sensor /1 (PS89) main body com- Open tray /3, the PF
does not turn ON within a specified pletes the paper front door and the verti-
period of time after the pick-up clutch / exit before stop- cal conveyance door /
1 (CL6) turns ON. ping operations. Up, and remove jammed
J13-03 The vertical conveyance sensor /1 paper if any.
(PS90) does not turn ON within a speci-
fied period of time after the pre-registra-
tion sensor /1 (PS89) turns ON.
J13-04 When the trailing edge of paper is pass- After completion
ing through the vertical conveyance of the exit of the
sensor /1 (PS90), the pre-registration preceding paper,
sensor /1 (PS89) is turned ON by the the main body
succeeding paper. stops operations.
J13-05 The vertical conveyance sensor /1 — Open the PF front door
When idling
534 2
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
(PF) not turn ON within a specified period of of paper being remove jammed paper if
time after the pick-up clutch /2 (CL9) printed when a any.
turns ON. jam occurs, the
J14-02 The pre-registration sensor /2 (PS93) main body com- Open tray /4, the PF
does not turn ON within a specified pletes the paper front door and the hori-
period of time after the pick-up clutch / exit before stop- zontal conveyance jam
2 (CL9) turns ON. ping operations. release lever and remove
J14-03 When the trailing edge of paper is pass- jammed paper if any.
ing through the loop sensor /2 (PS94),
the pre-registration sensor /2 (PS93) is
turned ON by the succeeding paper.
J14-04 The pre-registration sensor /2 (PS93) — Pull out tray /4 and
When idling
Tray 5 J15-01 The paper feed sensor /3 (PS84) does If there is a sheet Pull out tray /5 and
During operation
(PF) not turn ON within a specified period of of paper being remove jammed paper if
time after the pick-up clutch /3 (CL12) printed when a any.
turns ON. jam occurs, the
J15-02 The pre-registration sensor /3 (PS95) main body com- Open tray /5, the PF
does not turn ON within a specified pletes the paper front door and the verti-
period of time after the pick-up clutch / exit before stop- cal conveyance door /
3 (CL12) turns ON. ping operations. Lw, and remove jammed
J15-03 The vertical conveyance sensor /3 paper if any.
(PS96) does not turn ON within a speci-
fied period of time after the pre-registra-
tion sensor /3 (PS95) turns ON.
J15-04 When the trailing edge of paper is pass- After completion
ing through the vertical conveyance of the exit of the
sensor /3 (PS96), the pre-registration preceding paper,
sensor /3 (PS95) is turned ON by the the main body
succeeding paper. stops operations.
J15-05 The vertical conveyance sensor /3 — Open the PF front door
When idling
2 535
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
feed turn ON within a specified period of of paper being front doors /R and /L,
convey- time after the ADU deceleration sensor printed when a pull out the ADU section
ance (PS42) turns ON. jam occurs, the and remove jammed
(com- J17-02 The ADU deceleration sensor (PS42) main body com- paper if any.
mon to does not turn ON within a specified pletes the paper
each period of time after the loop sensor exit before stop-
tray) (PS16) turns ON. ping operations.
Paper J17-03 The loop sensor (PS16) does not turn After completion Open the main body ver-
feed ON within a specified period of time of the exit of the tical conveyance door
convey- after the vertical conveyance sensor /1 preceding paper, and remove jammed
ance (PS19) turns ON. the main body paper if any.
(trays 1/ stops operations.
and /2)
Paper J17-04 The vertical conveyance sensor /2
feed (PS20) does not turn ON within a speci-
convey- fied period of time after the vertical con-
ance veyance sensor /3 (PS21) turns ON.
(tray /2) J17-05 The vertical conveyance sensor /1
(PS19) does not turn ON within a speci-
fied period of time after the vertical con-
veyance sensor /2 (PS20) turns ON.
Paper J17-06 The loop sensor (PS16) does not turn Open the PF front door
feed ON within a specified period of time and the horizontal con-
convey- after the PF exit sensor (PS99) turns veyance jam release
ance (PF) ON. lever, and remove
jammed paper if any.
Paper J17-07 The paper leading edge sensor (PS41) — Open the main body
When idling
536
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
feed does not turn ON within a specified of paper being and the PF vertical con-
convey- period of time after the vertical convey- printed when a veyance door /Up, and
ance (PF) ance sensor /1 (PS90) turns ON. jam occurs, the remove jammed paper if
J18-02 The loop sensor /1 (PS92) does not main body com- any.
turn ON within a specified period of pletes the paper
time after the intermediate sensor /Up exit before stop-
(PS91) turns ON. ping operations.
J18-03 The loop sensor /2 (PS94) does not Open the PF front door
turn ON within a specified period of and the horizontal con-
time after the pre-registration sensor /2 veyance jam release
(PS93) turns ON. lever, and remove
jammed paper if any.
J18-04 The intermediate sensor /Lw (PS97) Open the PF front door
does not turn ON within a specified and the PF vertical con-
period of time after the vertical convey- veyance door /Lw, and
ance sensor /3 (PS96) turns ON. remove jammed paper if
J18-05 The loop sensor /3 (PS98) does not any.
turn ON within a specified period of
time after the intermediate sensor /Lw
(PS97) turns ON.
J18-06 The PF exit sensor (PS99) does not turn Open the PF front door,
ON within a specified period of time the PF vertical convey-
after the loop sensor /1 (PS92) turns ance door /Up and the
ON. horizontal conveyance
jam release lever, and
remove jammed paper if
any.
J18-07 The PF exit sensor (PS99) does not turn Open the PF front door
ON within a specified period of time and the PF horizontal
after the loop sensor /2 (PS94) turns conveyance jam release
ON. lever, and remove
jammed paper if any.
J18-08 The PF exit sensor (PS99) does not turn Open the PF front door,
ON within a specified period of time the PF vertical convey-
after the loop sensor /3 (PS98) turns ance door /Lw and the
ON. horizontal conveyance
jam release lever, and
remove jammed paper if
any.
J18-09 The intermediate sensor /Up (PS91) — Open the PF front door
When idling
537
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
When idling
/1050e/1050eP
538
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
paper does not turn ON within a specified of paper being front doors /R and /L,
exit period of time after the fusing exit sen- printed when a pull out the ADU section
sor (PS22) turns ON. jam occurs, the and remove jammed
J32-03 The reverse sensor /1 (PS48) does not main body com- paper if any.
turn ON within a specified period of pletes the paper
time after the ADU acceleration sensor exit before stop-
(PS49) turns ON. ping operations.
J32-04 The PS46 does not turn ON again
within a specified period of time after
the reverse sensor /1 (PS48) turns ON.
J32-05 The paper exit sensor (PS3) does not
turn ON within a specified period of
time after the reverse sensor /1 (PS48)
turns ON.
J32-06 The paper exit sensor (PS3) does not
turn OFF within a specified period of
time after the PS3 turns ON.
J32-07 The paper exit sensor (PS3) turns ON —
When idling
while in idling.
J32-08 The ADU acceleration sensor (PS49)
turns ON while in idling.
J32-09 The fusing exit sensor (PS22) turns ON
while in idling.
J32-10 The reverse/exit sensor (PS50) turns
ON while in idling.
J32-11 The fusing jam sensor (PS23) turns ON
while in idling.
J32-12 The reverse sensor /1 (PS48) turns ON
while in idling.
J32-13 The reverse sensor /2 (PS47) turns ON
while in idling.
External J51-01 The front door/R, /L of the main body The main body Open the main body
During operation
was opened while printing. stops immedi- front doors /R and /L,
ately. pull out the ADU section
and remove jammed
paper if any.
2 539
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
540
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
original, the original exit sensor /Lt immediately. If cover and remove
(PS307) does not turn ON within a there is paper jammed paper if any.
specified period of time after the original being transferred
reverse sensor (PS309) turns ON. or having been
J62-9 When exiting a large size single sided transferred, the
original, the original exit sensor /Lt main body com-
(PS307) does not turn OFF within a pletes the paper
specified period of time after it turns exit before stop-
ON. ping operations.
J62-10 When exiting a large size double sided
original, the original exit sensor /Lt
(PS307) does not turn OFF within a
specified period of time after it turns
ON.
J63-1 When outputting a large size double
sided original from the reverse section,
the original reverse sensor (PS309)
does not turn ON.
J63-2 When entering a large size double sided
original into the reverse section, the
original reverse sensor (PS309) does
not turn OFF within a specified period of
time after it turns ON.
J63-3 When outputting a large size double
sided original from the reverse section,
the original reverse sensor (PS309)
does not turn OFF within a specified
period of time after it turns ON.
J63-4 When exiting a small size single sided
original, the original exit sensor /Rt
(PS314) does not turn OFF within a
specified period of time after the original
reverse sensor (PS309) turns ON.
J63-5 When exiting a small size double sided
original, the original exit sensor /Rt
(PS314) does not turn OFF within a
specified period of time after the original
reverse/exit sensor (PS313) turns ON.
J63-6 When exiting a small size single sided
original, the original exit sensor /Rt
(PS314) does not turn OFF within a
specified period of time after it turns
ON.
541
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
original, the original exit sensor /Rt immediately. If cover and remove
(PS314) does not turn OFF within a there is paper jammed paper if any.
specified period of time after it turns being transferred
ON. or having been
J63-8 When entering a small size double transferred, the
sided original into the reverse section, main body com-
the original reverse sensor (PS309) pletes the paper
does not turn ON within a specified exit before stop-
period of time after original conveyance ping operations.
sensor (PS308) turns ON.
J63-9 When outputting a small size double
sided original from the reverse section,
the original reverse sensor (PS309)
does not turn ON within a specified
period of time after original conveyance
sensor (PS308) turns ON.
J63-10 When entering a small size double
sided original into the reverse section,
the original reverse sensor (PS309)
does not turn OFF within a specified
period of time after it turns ON.
J63-11 When outputting a small size double
sided original from the reverse section,
the original reverse sensor (PS309)
does not turn OFF within a specified
period of time after it turns ON.
J65-1 The original registration sensor /Rt
(PS306) turns ON while in idling.
J65-2 The original conveyance sensor
(PS308) turns ON while in idling.
J65-4 The original reverse sensor (PS309)
turns ON while in idling.
J65-8 The original exit sensor /Lt (PS307)
turns ON while in idling.
J65-10 The original reverse/exit sensor (PS313)
turns ON while in idling.
J65-20 The original exit sensor /Rt (PS314)
turns ON while in idling.
J65-40 The reverse jam sensor (PS304) turns
ON while in idling.
J65-80 The original registration sensor /Lt
(PS318) turns ON while in idling.
542
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
turn ON within a specified period of main body stop any from the FD/main
time after the main body paper exit sen- immediately. body.
sor (PS3) turns ON.
J72-02 The intermediate conveyance sensor
(PS13) does not turn ON within a speci-
fied period of time after the FD entrance
sensor (PS1) turns ON.
J72-03 The main tray exit sensor (PS18) does
not turn ON within a specified period of
time after the intermediate conveyance
sensor (PS13) turns ON.
J72-04 The main tray exit sensor (PS18) does
not turn OFF within a specified period of
time after it turns ON.
J72-05 The sub tray paper exit sensor (PS16)
does not turn ON within a specified
period of time after the intermediate
conveyance sensor (PS13) turns ON.
J72-06 The sub tray paper exit sensor (PS16)
does not turn OFF within a specified
period of time after it turns ON.
J72-09 The punch conveyance sensor (PS5)
does not turn ON within a specified
period of time after the FD entrance
sensor (PS1) turns ON.
J72-10 The 3rd folding conveyance sensor
(PS54) does not turn ON within a speci-
fied period of time after the punch con-
veyance sensor (PS5) turns ON.
J72-11 The punch registration sensor (PS6)
does not turn ON within a specified
period of time after the punch convey-
ance sensor (PS5) turns ON.
J72-12 The 1st folding conveyance sensor
(PS51) does not turn ON within a speci-
fied period of time after the punch regis-
tration sensor (PS6) turns ON.
J72-13 The 3rd folding conveyance sensor
(PS54) does not turn ON within a speci-
fied period of time after the 1st folding
conveyance sensor (PS51) turns ON.
J72-14 The intermediate conveyance sensor
(PS13) does not turn ON within a speci-
fied period of time after the 3rd folding
conveyance sensor (PS54) turns ON.
543
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
not turn ON within a specified period of main body stop if any, from the FS/main
time after the main body paper exit sen- immediately. body.
sor (PS3) turns ON.
J72-17 The main tray exit sensor (PS10) does
not turn OFF within a specified period of
time after the stacker entrance sensor
(PS5) turns OFF.
J72-18 The stacker entrance sensor (PS5)
does not turn ON within a specified
period of time after the FNS entrance
sensor (PS4) turns ON.
J72-19 While in stapling, the stacker entrance
sensor (PS5) does not turn OFF within a
specified period of time after the
stacker entrance motor (M13) turns
ON. While in any other operations than
stapling, the PS5 does not turn OFF
within a specified period of time after it
turns ON.
J72-20 While in stapling a small size paper, the
main tray exit sensor (PS10) does not
turn ON within a specified period of
time after the paper exit arm motor
(M23) turns ON.
J72-21 While in stapling a large size paper, the
main tray exit sensor (PS10) does not
turn OFF within a specified period of
time after the paper exit arm motor
(M23) turns ON.
J72-22 While in exiting paper in the sub tray,
the sub tray paper exit sensor (PS1)
does not turn ON within a specified
period of time after the FNS entrance
sensor (PS4) turns ON.
J72-23 While in exiting paper in the sub tray,
the sub tray paper exit sensor (PS1)
does not turn OFF within a specified
period of time after the PS1 turns ON.
J72-28 While in the straight/shift of the small
size paper, the main tray paper exit sen-
sor (PS10) does not turn OFF within a
specified period of time after the PS10
turns ON.
544
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
main tray paper exit sensor (PS10) does main body stop if any, from the FS/main
not turn OFF within a specified period of immediately. body.
time after the PS10 turns ON.
J72-39 The door switch (MS1) turns OFF while The copier stops Close the front door.
in the copy/print. immediately.
FD J72-40 While in the folding operation, the 2nd The FD and the Remove jammed paper if
folding conveyance sensor (PS53) does main body stop any from the FD/main
not turn ON within a specified period of immediately. body.
time after the 1st folding motor (M4)
starts to accelerate.
J72-41 While in the folding operation, the 3rd
folding conveyance sensor (PS54) does
not turn ON within a specified period of
time after the 1st folding motor (M4)
starts to accelerate.
J72-42 While in the folding operation, the 3rd
folding conveyance sensor (PS54) does
not turn ON within a specified period of
time after the 2nd folding motor (M5)
starts to accelerate.
J72-43 While in the folding operation, the inter-
mediate conveyance sensor (PS13)
does not turn ON within a specified
period of time after the 3rd folding
motor (M6) starts to accelerate.
J72-44 While in the folding operation, the 3rd
folding conveyance sensor (PS54) does
not turn ON within a specified period of
time after the 2nd folding conveyance
sensor (PS53) turns ON.
J72-45 While in the folding operation, the inter-
mediate conveyance sensor (PS13)
does not turn ON within a specified
period of time after the 3rd folding con-
veyance sensor (PS54) turns ON.
J72-46 The PI conveyance sensor /Up (PS31)
does not turn ON within a specified
period of time after the PI pick-up sole-
noid /Up (SD13) turns ON.
J72-47 The PI exit sensor (PS4) does not turn
ON within a specified period of time
after the PI conveyance sensor /Up
(PS31) turns ON.
545
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
does not turn ON within a specified main body stop any from the FD/main
period of time after the PI pick-up sole- immediately. body.
noid /Lw (SD14) turns ON.
J72-49 The PI exit sensor (PS4) does not turn
ON within a specified period of time
after the PI conveyance sensor /Lw
(PS37) turns ON.
J72-50 The FD entrance sensor (PS1) does not
turn ON within a specified period of
time after the PI exit sensor (PS4) turns
ON.
J72-58 The PI multi feed is detected.
J72-59 The door switch (MS1) turns OFF.
SD J72-61 The entrance sensor (PS1) does not The SD and the Remove jammed paper if
turn ON within a specified period of main body stop any from the SD/main
time after the exit sensor (PS3) on the immediately. body.
main body turns ON.
J72-62 The horizontal conveyance sensor /1
(PS2) does not turn ON within a speci-
fied period of time after the entrance
sensor (PS1) turns ON.
J72-63 The horizontal conveyance sensor /2
(PS3) does not turn ON within a speci-
fied period of time after the horizontal
conveyance sensor /1 (PS2) turns ON.
J72-64 The horizontal conveyance exit sensor
(PS4) does not turn ON within a speci-
fied period of time after the horizontal
conveyance sensor /2 (PS3) turns ON.
J72-65 The horizontal conveyance exit sensor
(PS4) does not turn OFF within a speci-
fied period of time after it turns ON.
J72-66 The subtray exit sensor (PS11) does
not turn ON within a specified period of
time after the horizontal conveyance
sensor /1 (PS2) turns ON.
J72-67 The subtray exit sensor (PS11) does
not turn OFF within a specified period of
time after it turns ON.
J72-68 The entrance sensor (PS1) does not
turn ON within a specified period of
time after the exit sensor (PS3) on the
main body turns ON.
546 2
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
(PS6) does not turn ON within a speci- main body stop any from the SD/main
fied period of time after the right angle immediately. body.
conveyance motor (M6) turns ON.
J72-70 The folding sensor /1 (PS7) does not
turn ON within a specified period of
time after the folding entrance motor
(M3) turns ON.
J72-71 The saddle stitching paper sensor
(PS13) does not turn ON within a speci-
fied period of time after the folding sub
scan alignment exit motor (M8) turns
ON.
J72-72 The bundle sensor /1 (PS14) does not
turn ON within a specified period of
time after the bundle arm rotation motor
(M22) turns ON.
J72-73 The bundle sensor /2 (PS15) does not
turn ON within a specified period of
time after the bundle clip motor (M11)
turns ON.
J72-74 The bundle sensor /4 (PS54) does not
turn ON within a specified period of
time after the bundle sensor /2 (PS15)
turns ON.
J72-75 The entrance sensor (PS1) does not
turn Off within a specified period of time
after it turns ON.
J72-76 The horizontal conveyance sensor
(PS3) does not turn OFF within a speci-
fied period of time after the entrance
sensor (PS1) turns ON.
J72-77 The right angle conveyance sensor /2
(PS6) does not turn OFF within a speci-
fied period of time after the folding
entrance motor (M3) turns ON.
J72-78 The folding sensor /2 (PS44) does not
turn OFF within a specified period of
time after the folding sub scan align-
ment exit motor (M8) turns ON.
J72-79 The saddle stitching paper sensor
(PS13) does not turn OFF within a
specified period of time after the folding
sub scan alignment exit motor (M8)
turns ON.
2 547
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
OFF within a specified period of time after main body stop any from the SD/main
the bundle clip motor (M11) turns ON. immediately. body.
J72-81 The bundle sensor /2 (PS15) does not
turn OFF within a specified period of
time after the bundle registration motor
(M12) turns ON.
J72-82 With paper bundle exit, the bundle sen-
sor /4 (PS54) does not turn OFF within
a specified period of time after the bun-
dle registration motor (M12) turns ON.
J72-83 The folding passage sensor (PS8) does
not turn ON within a specified period of
time after the folding conveyance motor
(M4) turns ON.
J72-84 The tri-folding exit sensor (PS9) does
not turn ON within a specified period of
time after the folding conveyance motor
(M4) turns ON.
J72-85 The folding sub scan alignment exit
motor (M8) does not turn OFF within a
specified period of time after it turns ON.
J72-86 The folding passage sensor (PS8) does
not turn OFF within a specified period of
time after the folding conveyance motor
(M4) turns ON.
J72-87 The tri-folding exit sensor (PS9) does
not turn OFF within a specified period of
time after it turns ON.
J72-88 With paper bundle exit, the bundle sen-
sor /2 (PS15) does not turn OFF within a
specified period of time after it turns ON.
J72-89 The trimmer registration sensor (PS55)
does not turn OFF within a specified
period of time after the bundle press
movement motor (M17) turns ON.
J72-90 The trimmer registration sensor (PS55)
does not turn ON within a specified
period of time after the bundle registra-
tion motor (M12) turns ON.
J72-99 During printing, either the SD front door
switch /Rt (MS1) or /Lt (MS2) turns OFF.
FS J73-01 The stacker entrance sensor (PS5) — Open the FS front door
When idling
548 2
Field Service Ver3.0 Nov.2006 13. JAM CODE
When idling
1050e/1050eP
turns ON while in idling. Or, the stack and the jam release lever,
empty sensor (PS20) turns ON while and remove jammed
turning ON the power source. paper, if any.
J73-04 The sub tray paper exit sensor (PS1)
turns ON while in idling.
FD J73-05 Either of the FD entrance sensor (PS1), — Open the FD front door,
the punch conveyance sensor (PS5) open then the entrance
and the punch registration sensor (PS6) conveyance jam release
turns ON while in idling. levers /1 and /2 and the
punch conveyance jam
release levers /1 and /2,
and then remove
jammed paper, if any.
J73-06 Either of the intermediate conveyance Open the FD front door
sensor (PS13), the sub tray paper exit and the intermediate
sensor (PS16) and the main tray paper conveyance jam lever,
exit sensor (PS18) turns ON while in and remove the jammed
idling. paper, if any.
J73-07 Either of the 1st folding conveyance Open the FD front door,
sensor (PS51), the 2nd folding convey- pull out the folding con-
ance sensor (PS53), the 3rd folding veyance section, open
conveyance sensor (PS54), the S size the folding conveyance
conveyance sensor (PS58), the folding jam release levers /1 to /
entrance sensor (PS52) and the folding 5, and remove jammed
exit sensor (PS2) turns ON while in paper, if any.
idling.
J73-08 Either of the PI conveyance sensor /Up Open the FD upper door
(PS31), the PI conveyance sensor /Lw and remove jammed
(PS37) and the PI exit sensor (PS4) paper, if any. When
turns ON while in idling. jammed paper gets in
the PI exit, open the
entrance conveyance
jam release lever /1 and
remove the jammed
paper.
SD J73-09 The entrance sensor (PS1) turns ON Open the SD front door /
while in idling. Rt and remove jammed
J73-10 Either of the horizontal conveyance paper, if any.
sensor /1 (PS2), the horizontal convey-
ance sensor /2 (PS3), or the subtray
exit sensor (PS11) turns ON while in
idling.
J73-11 The horizontal conveyance exit sensor Open the SD front door /
(PS4) turns ON while in idling. Lt and remove jammed
paper, if any.
1 549
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
When idling
/1050e/1050eP
550 1
Field Service Ver3.0 Nov.2006 13. JAM CODE
When idling
1050e/1050eP
and /3 (PS7, 16 and 17) of the tandem LS JAM door, and
(2nd) LS turns ON while in idling. remove jammed paper, if
However, in the case of LS-502, only any.
the conveyance sensor /1 (PS7) is
applicable.
J73-24 The coupling exit sensor (PS18) of the Open the tandem (2nd)
tandem (2nd) LS turns ON while in LS front door, open then
idling. the coupling exit jam
However, in the case of LS-501 only. release lever and remove
jammed paper, if any.
PB J73-30 The entrance sensor (PS1) turns ON Open the front door and
while in idling. remove jammed paper, if
The SC entrance sensor (PS2) turns ON any.
while in idling.
The cover paper entrance sensor (PS3)
turns ON while in idling.
The sub tray exit sensor (PS4) turns ON Open the upper door
while in idling. and remove jammed
paper, if any.
J73-31 The SC paper detection sensor (PS16) Open the front door and
turns ON while in idling. remove jammed paper, if
J73-32 The clamp paper sensor (PS28) turns any.
ON while in idling.
J73-33 The cover paper switchback sensor
(PS44) turns ON while in idling.
The cover paper sensor/Rt (PS45) turns
ON while in idling.
The cover paper sensor/Lt (PS46) turns
ON while in idling.
J73-34 The book end sensor (PS61) turns ON Open the stacker door
while in idling. and remove jammed
paper, if any.
J73-35 The cover paper conveyance sensor /1 Pull out the paper feed
(PS75) turns ON while in idling. tray and remove jammed
The cover paper conveyance sensor /2 paper, if any.
(PS76) turns ON while in idling.
The cover paper conveyance sensor /3
(PS77) turns ON while in idling.
The cover paper conveyance sensor /4
(PS78) turns ON while in idling.
The cover paper conveyance sensor /5
(PS79) turns ON while in idling.
2 551
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
dem (1st) LS does not turn ON within a main body stop if any, from the LS/main
specified period of time after the main immediately. body.
body paper exit sensor (PS3) turns ON.
J74-02 The entrance sensor (PS4) of the tan-
dem (1st) LS does not turn OFF within a
specified period of time after it turns ON.
J74-03 The sub tray exit sensor (PS10) does
During operation
552
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
tandem (1st) LS does not turn OFF main body stop if any, from the LS/main
within a specified period of time after it immediately. body.
turns ON.
J74-19 The LS front door open jam. While in
any other modes than the tandem
mode, the front door switch (MS1) of
the tandem (1st) LS turns OFF while in
the print/print.
J74-31 The entrance sensor (PS4) of the tan-
dem (2nd) LS does not turn ON within a
specified period of time after the cou-
pling exit sensor (PS18) of the tandem
(1st) LS turns ON.
J74-32 The entrance sensor (PS4) of the tan-
dem (2nd) LS does not turn OFF within a
specified period of time after it turns ON.
J74-33 The sub tray exit sensor (PS10) does
not turn ON within a specified period of
time after the entrance sensor (PS4) of
the tandem (2nd) LS turns ON.
J74-34 The sub tray exit sensor (PS10) of the
tandem (2nd) LS does not turn OFF
within a specified period of time after it
turns ON.
J74-35 The conveyance sensor /1 (PS7) does
not turn ON within a specified period of
time after the entrance sensor (PS4) of
the tandem (2nd) LS turns ON.
J74-36 The conveyance sensor /1 (PS7) of the
tandem (2nd) LS does not turn OFF
within a specified period of time after it
turns ON.
J74-37 The conveyance sensor /2 (PS16) does
not turn ON within a specified period of
time after the conveyance sensor /1
(PS7) of the tandem (2nd) LS turns ON.
J74-38 The conveyance sensor /2 (PS16) of
the tandem (2nd) LS does not turn OFF
within a specified period of time after it
turns ON.
J74-39 The conveyance sensor /3 (PS17) does
not turn ON within a specified period of
time after the conveyance sensor /2
(PS16) of the tandem (2nd) LS turns
ON.
553
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
the tandem (1st) LS does not turn OFF main body stop if any, from the LS/main
within a specified period of time after it immediately. body.
turns ON.
J74-41 The coupling exit sensor (PS18) does
not turn ON within a specified period of
time after the conveyance sensor /3
(PS17) of the tandem (2nd) LS turns
ON.
J74-42 The coupling exit sensor (PS18) of the
tandem (2nd) LS does not turn OFF
within a specified period of time after it
turns ON.
J74-49 The LS front door open jam. While in
any other modes other than the tandem
mode, the front door switch (MS1) of
the tandem (2nd) LS turns OFF while in
the print/print.
PB J74-60 The entrance sensor (PS1) does not The PB and the Remove jammed paper,
turn ON within a specified period of main body stop if any, from the PB/main
time after the main body paper exit sen- immediately. body.
sor (PS3) turns ON.
J74-61 The SC entrance sensor (PS2) does not
turn ON within a specified period of
time after the entrance sensor (PS1)
turns ON.
J74-62 The SC entrance sensor (PS2) does not
turn OFF within a specified period of
time after it turns ON.
J74-63 The cover paper entrance sensor (PS3)
does not turn ON within a specified
period of time after the main body
paper exit sensor (PS3) turns ON.
J74-64 The sub tray exit sensor (PS4) does not
turn ON within a specified period of
time after the entrance sensor (PS1)
turns ON.
J74-65 The sub tray exit sensor (PS4) does not
turn OFF within a specified period of
time after it turns ON.
J74-66 The SC paper detection sensor (PS16)
does not turn ON within a specified
period of time after the SC entrance
sensor (PS2) turns ON.
554 2
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
does not turn OFF within a specified main body stop if any, from the PB/main
period of time after it turns ON. immediately. body.
J74-68 When conveying two pages at a time,
the SC paper detection sensor (PS16)
does not turn ON within a specified
time period after the SC entrance sen-
sor (PS2) turns ON.
J74-69 When conveying two pages at a time,
the SC paper detection sensor (PS16)
does not turn OFF within a specified
period of time after it turns ON.
J74-70 The SC paper detection sensor (PS16)
does not turn OFF within a specified
period of time after the SC bundle con-
veynace motor (M17) turns ON.
J74-71 The clamp paper sensor (PS28) does
not turn OFF within a specified period of
time after the Clamp motor (M22) turns
OFF.
J74-72 The glue apply position detection sen-
sor (PS32) does not turn ON within a
specified period of time after reversal of
glue tank movement motor (the tank
moves back) turns ON.
J74-73 The glue apply position detection sen-
sor (PS32) does not turn OFF within a
specified period of time after it turns
ON.
J74-74 The cover paper sensor/Rt (PS45) does
not turn ON within a specified period of
time after the cover paper pick up
clutch (MC71) turns ON.
J74-76 When starting trimming of the cover
paper fed from the PB, the cover paper
switchback sensor (PS44) does not
turn ON within a specified time period
after the cover paper conveyance
motor (M45) turns ON.
J74-77 When trimming of the cover paper fed
from the PB is complete, the cover
paper switchback sensor (PS44) does
not turn OFF within a specified time
period after the cover paper convey-
ance motor (M45) turns ON.
2 555
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
the cover paper fed from the PB, the main body stop if any, from the PB/main
cover paper sensor/Lt (PS46) does not immediately. body.
turn OFF within a specified time period
after the cover paper conveyance
motor (M45) turns ON.
J74-79 When positioning the leading edge of
the cover paper fed from the PB, the
cover paper sensor/Lt (PS46) does not
turn ON within a specified time period
after the cover paper conveyance
motor (M45) turns ON.
J74-80 When cover paper is fed from the main
body, the cover paper sensor/Rt (PS45)
does not turn OFF within a specified
time period after the cover paper
entrance sensor (PS3) turns ON.
J74-82 When starting trimming of the cover
paper fed from the main body, the
cover paper switchback sensor (PS44)
does not turn ON within a specified
period of time after the cover paper
conveyance motor (M45) turns ON.
J74-83 When trimming of the cover paper fed
from the main body is complete, the
cover paper switchback sensor (PS44)
does not turn OFF within a specified
period of time after the cover paper
conveyance motor (M45) turns ON.
J74-84 When positioning the leading edge of
the cover paper fed from the main
body, the cover paper sensor/Lt (PS46)
does not turn OFF within a specified
time period after the cover paper con-
veyance motor (M45) turns ON.
J74-85 When positioning the leading edge of
the cover paper fed from the main
body, the cover paper sensor/Lt (PS46)
does not turn ON within a specified
time period after the cover paper con-
veyance motor (M45) turns ON.
J74-86 The book end sensor (PS61) does not
turn ON within a specified period of
time after the book conveyance belt
motor (M61) turns ON.
556 2
Field Service Ver3.0 Nov.2006 13. JAM CODE
During operation
1050e/1050eP
sor /1 (PS66) does not turn ON within a main body stop if any, from the PB/main
specified period of time after the book immediately. body.
conveyance belt up down motor (M63)
turns ON.
J74-88 When first row of book moves, the
book sensor /2 (PS67) does not turn
ON within a specified period of time
after the book movement motor (M64)
turns ON.
J74-89 When feeding paper, the cover paper
conveyance sensor /1 (PS75) does not
turn ON within a specified period of
time after the cover paper pick up
clutch (MC71) turns ON.
J74-90 The cover paper conveyance sensor /2
(PS76) does not turn ON within a speci-
fied period of time after the cover paper
conveyance sensor /1 (PS75) turns ON.
J74-91 When re-feeding paper, the cover paper
conveyance sensor /3 (PS77) does not
turn ON within a specified period of
time after the cover paper pick up
clutch (MC71) turns ON.
J74-92 The cover paper conveyance sensor /4
(PS78) does not turn ON within a speci-
fied period of time after the cover paper
conveyance sensor /3 (PS77) turns ON.
J74-93 The multi feed detection board /2
(MFDTB72) turns OFF.
J74-96 The cover paper switchback sensor
(PS44) does not turn ON within a speci-
fied period of time after the cover paper
feed motor (M74) turns ON.
J74-97 No paper is detected (the paper has
removed) when restarting the job after
recovery.
J74-98 A cover paper has not been conveyed
to the cover paper table section when
clamping of inside pages is finished.
J74-99 The front door switch (MS2), the upper
door switch (MS3) and the stacker door
switch (MS4) became OFF during print-
ing.
2 557
13. JAM CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
During operation
/1050e/1050eP
not turn ON within a specified period of of paper being front doors /R and /L,
time after the reverse sensor /1 (PS48) printed when a pull out the ADU section
turns ON. jam occurs, the and remove jammed
J92-02 The ADU reverse sensor /1 (PS46) does main body com- paper if any.
not turn ON again within a specified pletes the paper
period of time after the PS46 turns ON. exit before stop-
ping operations.
J92-03 The ADU reverse sensor /1 (PS46) —
When idling
turn ON within a specified period of of paper being front doors /R and /L,
time after the ADU reverse sensor /1 printed when a pull out the ADU section
(PS46) turns ON. jam occurs, the and remove jammed
main body com- paper if any.
pletes the paper
exit before stop-
ping operations.
J93-02 The ADU conveyance sensor /1 (PS35) —
When idling
while in idling.
558
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
A. Note for use
Turn OFF/ON the power switch (SW2) of the main body when releasing an abnormal condition.
B. Code list
NOTE
• For codes with "*" in the code column, "Turn ON the power switch again" is displayed on the touch
panel. For other codes, "Please call service" is displayed.
• For codes with "**" in the code column (SC78-40 to 62: perfect binding tank temperature abnor-
mality related), always repair defective parts then set the DipSW3-1 software of service mode to 0.
If DipSW3-1 is set to 0 before defective parts are fixed, it may cause fire.
paper feed motor (M4) is checked. stops immediately Printer control board (PRCB)
An error detection signal is to turn OFF the
detected twice in succession a RL1 (main).
specified period of time after M4
was turned ON (the first signal is
ignored).
SC13-02 An abnormal speed signal of the Paper feed motor (M40)
PF
2 559
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
560
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
(PS12) is OFF, PS12 does not turn displayed on the
ON within 20 seconds after the operation panel,
paper lift motor /2 (M26) turns ON but displayed only
for lifting operation. And at this on the data collec-
time, an error detection signal is tion, the list output
not detected. and CSRC. Since
the lifting opera-
tion of the tray is
not completed,
"Set paper in the
tray 2" is displayed
on the operation
board.
Tray /3 SC18-30 The locking of the paper lift motor The main body Paper lift motor /1 (M42)
PF
561
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
562
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
(PS83) is OFF, PS83 does not turn displayed on the
ON within 20 seconds after the operation panel,
paper lift motor /3 (M44) turns ON but displayed only
for lifting operation. And at this on the data collec-
time, an error detection signal is tion, the list output
not detected. and CSRC. Since
the lifting opera-
tion of the tray is
not completed,
"Set paper in the
tray 5" is displayed
on the operation
board.
Wire SC21-01 It is checked that the time for the The main body Charger cleaning motor
Main body
563
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
564
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
cleaning the transfer/separation cleaning stops immediately ing motor (M20)
abnor- motor (M20) are over. to turn OFF the Transfer/separation clean-
mality • When the transfer/separation RL1 (main). ing home sensor (PS38)
cleaning home sensor (PS38) Transfer/separation clean-
is OFF with the main power ing limit sensor (PS39)
switch (SW1) ON, PS38 does ADU drive boards /1, /2
not turn ON within a specified (ADUDB/1, /2)
period of time after the trans-
fer/separation cleaning motor
(M20) turns ON for a home
position research operation
(return operation). At this time,
an error detection signal
(blowout of a fuse) is not
detected.
• PS38 does not turn OFF within
a specified period of time after
the reverse operation (return
operation) is started. At this
time, an error detection signal
(blowout of a fuse) is not
detected.
• The transfer/separation clean-
ing limit sensor (PS39) does
not turn ON within a specified
period of time after the reverse
operation (return operation) is
started for detection of PS38
being OFF. Or, PS38 does not
turn ON within a specified
period of time after PS39 turns
ON. At this time, an error
detection signal (blowout of a
fuse) is not detected.
565
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
566
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
cleaning the transfer assist motor is out. stops immediately Transfer assist home sensor
abnor- The transfer assist home sensor to turn OFF the (PS37)
mality (PS37) does not turn ON within a RL1 (main). ADU drive boards /1, /2
specified period of time after the (ADUDB/1, /2)
home position search operation of
the transfer assist motor (M19) is
started.
SC21-08 An error is detected while in the Transfer assist motor (M19)
operation of the transfer assist Transfer/separation clean-
motor. ing limit sensor (PS39)
An error is detected of the transfer Transfer assist home sensor
assist motor (M19) while in the (PS37)
print operation.
Motor SC23-01 The speed error signal of the toner Toner bottle motor (M6)
abnor- bottle motor (M6) is checked. Printer control board (PRCB)
mality An error detection signal is Toner bottle/large capacity
detected twice in succession a hopper
specified period of time after M6
turns ON (the first signal is
ignored).
SC23-02 The speed error signal of the Developing motor (M3)
developing motor (M3) is checked. Printer control board (PRCB)
Since an error detection signal is
detected a second after M3 turns
ON, turn OFF M3 for 0.5 seconds.
Then, an error detection signal is
detected again a second after it is
turned ON again.
SC23-03 The locking of the blade motor is Blade motor (M22)
detected. Blade sensor /1 (PS24), /2
The error detection signal (over (PS25)
current) of M22 is detected.
SC23-04 It is checked that the movement of DC power supply /2 (DCPS/
the blade motor (M22) is not com- 2)
pleted, and the 24V power source
is also checked.
The drum READY1 signal (READY
condition) cannot be detected
within a specified period of time
after the drum motor (M2) turns
ON. Or, the drum READY1 signal
(READY release condition) cannot
be detected within a specified
period of time after M2 turns OFF.
At this time, an error detection sig-
nal (24V cut out) is detected.
567
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- blade motor (M22) in the printer stops immediately Printer control board (PRCB)
mality control board (PRCB) is checked. to turn OFF the
The drum READY1 signal (READY RL1 (main).
condition) cannot be detected
within a specified period of time
after the drum motor (M2) turns
ON. Or, the drum READY1 signal
(READY release condition) cannot
be detected within a specified
period of time after M2 turns OFF.
At this time, the error detection
signal (blowout of a fuse) of the
blade motor (M22) is detected.
SC23-06 It is checked that the movement of
the blade motor (M22) is not com-
pleted.
The drum READY1 signal (READY
condition) cannot be detected
within a specified period of time
after the drum motor (M2) turns
ON. Or, the drum READY1 signal
(READY release condition) cannot
be detected within a specified
period of time after M2 turns OFF.
At this time, an error detection sig-
nal is not detected.
SC23-07 It is checked that the movement of DC power supply /2 (DCPS/
the blade motor (M22) is not com- 2)
pleted, and 24V power source is
also checked.
The blade READY signal (READY
condition) cannot be detected
within a specified period of time
after the blade replacement signal
turns ON. Or, the blade READY
signal (READY release condition)
cannot be detected within a spec-
ified period of time after the blade
replacement signal turns OFF. At
this time, an error detection signal
(24V cut off) is detected.
568
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- blade motor (M22) in the printer stops immediately Printer control board (PRCB)
mality control board (PRCB) is checked. to turn OFF the
The blade READY signal (READY RL1 (main).
condition) cannot be detected
within a specified period of time
after the blade replacement signal
turns ON. Or, the blade READY
signal (READY release condition)
cannot be detected within a spec-
ified period of time after the blade
replacement signal turns OFF. At
this time, an error detection signal
(blowout of a fuse) of the blade
motor (M22) is detected.
SC23-09 It is checked that the movement of
the blade motor (M22) is not com-
pleted. The blade READY signal
(READY condition) cannot be
detected within a specified period
of time after the blade replace-
ment signal turns ON. Or, the
blade READY signal (READY
release condition) cannot be
detected within a specified period
of time after the blade replace-
ment signal turns OFF. At this
time, an error detection signal is
not detected.
SC23-10 It is checked that the drum motor Drum motor (M2)
(M2) does not start. The drum Printer control board (PRCB)
READY2 signal (READY signal) is
not detected within a specified
period of time after M2 turns ON.
SC23-11 The blowout of a fuse for the inter- Intermediate hopper motor
mediate hopper motor (M11) in (M11)
the printer control board (PRCB) is Printer control board (PRCB)
checked.
An error detection signal (blowout
of a fuse) is detected when M11
turns ON.
569
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- separation motor (M10) in the stops immediately Printer control board (PRCB)
mality printer control board (PRCB) is to turn OFF the
checked. RL1 (main).
An error detection signal (blowout
of a fuse) is detected when M10
turns ON.
Toner SC23-13 Air separation motor (M10) rota- Air separation motor (M10)
convey- tion abnormality. Since an error is Air motor encoder sensor
ance detected when M10 turns ON, (PS30)
abnor- turn it OFF. An error is still Resetting of the intermedi-
mality detected when turn it ON again. ate toner hopper section
SC23-14 The toner conveyance abnormality Toner pump motor (M28)
is detected. When toner is sup- Air pump motor (M29)
plied for 8 minutes and the toner Toner remaining sensor /1
remaining sensor /1 (PS31) does (PS31)
not turn ON, it is found that the Toner remaining sensor /3
toner remaining sensor /3 (PS33) (PS33)
of the large capacity hopper turns
ON for the last 15 seconds in suc- Note:
cession. • When the code SC23-
14 occurs, be sure to
repair defective parts
before setting the
software DIPSW3-1 to
0. Setting the
DIPSW3-1 to 0 with-
out repairing defec-
tive parts may cause
toner to overflow
inside and outside of
the machine.
SC23-15 Toner remaining detection sensor / Toner remaining sensor /2
3 (PS33) abnormality. When the (PS32)
toner remaining sensor /1 (PS31) Toner remaining sensor /3
does not turn ON even if toner is (PS33)
supplied for 8 minutes, it is found
that the toner remaining sensor /2
(PS32) of the large capacity hop-
per turns ON for the last 15 sec-
onds in succession, and the toner
remaining sensor /3 (PS33) turns
OFF.
570
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
convey- detected. When the toner pump stops immediately Air pump motor (M29)
ance motor (M28) is operating, the to turn OFF the Toner remaining sensor /4
abnor- toner remaining sensor /4 (PS34) RL1 (main). (PS34)
mality detects the toner being provided
in succession for 20 seconds. Note:
• When the code SC23-
17 occurs, be sure to
repair defective parts
before setting the
software DIPSW3-1 to
0. Setting the
DIPSW3-1 to 0 with-
out repairing defec-
tive parts may cause
toner to overflow
inside and outside of
the machine.
SC23-20 Toner pump motor (M28) abnor- DC power supply /2 (DCPS/
mality. The rotation of the toner 2)
pump motor (M28) and the 24 V Toner pump motor (M28)
power source are checked. While
M28 is rotating, an error detection
signal (abnormal rotation) is
detected for more than 1 second.
At this time, an error detection sig-
nal (24V cut off) is detected.
SC23-21 • Toner pump motor (M28) Printer control board (PRCB)
abnormality. The blowout of a Toner pump motor (M28)
fuse for the toner pump motor Recycle cut motor (M30)
(M28) in the printer control
board (PRCB) is checked.
While M28 is rotating, an error
detection signal (abnormal
rotation) is detected for more
than 1 second. At this time, an
error detection signal (blowout
of a fuse) is detected, but an
error signal (24V cut off) is not
detected.
• When recycle cut motor (M30)
is operating, abnormality
detection signal was continu-
ously detected twice for the
specified time. (First time
ignored)
2 571
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
convey- mality. The rotation of the toner stops immediately Pump encoder sensor /1
ance pump motor (M28) is checked. to turn OFF the (PS28)
abnor- While M28 is rotating, an error RL1 (main).
mality detection signal (abnormal rota-
tion) is detected for more than 1
second. At this time, error signals
(blowout of a fuse and 24V cut off)
are not detected.
SC23-24 Air pump motor (M29) abnormal- DC power supply /2 (DCPS/
ity. The rotation of the air pump 2)
motor (M29) and the 24V power Air pump motor (M29)
source are checked.
While M29 is rotating, an error
detection signal (abnormal rota-
tion) is detected for more than 1
second. At this time, an error sig-
nal (24V cut off) is detected.
SC23-25 Air pump motor (M29) abnormal- Printer control board (PRCB)
ity. The blowout of a fuse for the Air pump motor (M29)
air pump motor (M29) in the
printer control board (PRCB) is
checked.
While M29 is rotating, an error
detection signal (abnormal rota-
tion) is detected for more than 1
second. At this time, an abnormal-
ity signal (blowout of a fuse) is
detected, but no abnormality sig-
nal (24V cut off) is detected.
SC23-26 Air pump motor (M29) abnormal- Air pump motor (M29)
ity. The rotation of the air pump Pump encoder sensor
motor (M29) is checked for more (PS29)
than 1 second. An error detection Load of the pump
signal (abnormal rotation) is
detected for more than 1 second.
At this time, error signals (blowout
of a fuse and 24V cut off) are not
detected.
572
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
convey- toner amount
ance exceeds 80% of
abnor- the toner collec-
mality tion box, a warn-
ing message is
displayed in the
operation panel
and the recycle
cut motor (M30) is
stopped after spe-
cific printing.
Drum SC24-01 When the change in temperature The main body Drum temperature sensor
of the drum temperature sensor stops immediately (TH5)
(TH5) is less than -2°C a specified to turn OFF the
period of time after the main RL1 (main).
power switch (SW1) turns ON to
start the control of the dehumidifi-
cation heater /1 (HTR1) and the
drum temperature is below 10°C
after the elapse of 1 minute.
SC24-02 When the main power switch
(SW1) turns ON with the fusing
temperature below 50°C, the
detected temperature of the drum
temperature sensor (TH5) is more
than 52°C, and when the detected
temperature is above 52°C after a
specified period of time.
High SC28-01 A charge leak is detected. After a Charger
voltage charge error detection signal is Power feeding contact
power detected while in the charge ON, High voltage unit /1 (HV1)
source up to 5 charge ON/OFF opera-
abnor- tions occur in succession while in
mality 10 prints.
SC28-02 A transfer leak is detected. After a Transfer/separation charger
transfer error detection signal is Power feeding point
detected while in the transfer ON, High voltage unit /2 (HV2)
up to 5 transfer ON/OFF opera-
tions occur in succession while in
10 prints.
SC28-03 A separation leak is detected.
After a separation error detection
signal is detected while in the sep-
aration ON, up to 5 separation
ON/OFF operations occur in suc-
cession while in 10 prints.
2 573
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
574 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- mality. While in the gamma correc- displayed on the (TCSB)
mality tion, a patch for control is not operation panel, Write unit
output. (No output is made from but displayed only Image processing board
the gamma sensor.) on the data collec- (IPB)
tion, the list output Overall control board
and the CSRC. (OACB)
SC29-06 The gamma correction data is The control of the Image processing board
defective. The gamma correction main body is (IPB)
output is abnormal. A regression made by using a Printer control board (PRCB)
error when carrying out a gamma data previously
curve operation while in the obtained.
gamma correction.
SC29-07 The dirt correction of the sensor is The main body Toner control sensor board
not completed. While in the dot stops immediately (TCSB) (gamma sensor
diameter correction, the dirt cor- to turn OFF the cleaning required)
rection of the gamma sensor is RL1 (main).
not sufficient. When gamma sen-
sor less than the specified value is
detected five times in succession,
this error code is displayed.
SC29-08 Correction abnormality. While in Error code is not Image processing board
the dot diameter correction, the displayed on the (IPB)
correction is terminated with an operation panel, Printer control board (PRCB)
abnormal value. but displayed only
on the data collec-
tion, the list output
and the CSRC.
The control of the
main body is
made by using a
data previously
obtained.
SC29-09 Drum potential sensor (DPS) out- The main body Drum potential sensor (DPS)
put abnormality. While in the 0V stops immediately Printer control board (PRCB)
check of the DPS, more than to turn OFF the
100V of the drum surface potential RL1 (main).
is detected more than 5 times.
When the error code is detected 5
times in succession, this error
code is displayed.
2 575
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- put abnormality. While in the drum stops immediately Printer control board (PRCB)
mality potential correction, a patch for to turn OFF the
control is not output with the V1 RL1 (main).
getting to more than 350V. When
this condition is detected 5 times
in succession, the error code is
displayed.
SC29-11 The data is defective. While in the
drum potential correction, no con-
vergence is obtained even after
correction is made more than 10
times. When this condition is
detected 5 times in succession,
the error code is displayed.
SC29-12 Auto adjustment monitor value Error code is not High voltage unit /2 (HV2)
abnormality. No convergence is displayed on the
made in the auto adjustment of operation panel,
the transfer current. but displayed only
SC29-13 Auto adjustment monitor value on the data collec-
abnormality. No convergence is tion, the list output
made in the auto adjustment of and the CSRC.
the separation (AC) current. The control of the
SC29-14 Auto adjustment monitor value main body is
abnormality. No convergence is made by using a
made in the auto adjustment of data previously
the separation (DC) current. obtained.
576
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- (FM12) is checked, and the 24V stops immediately 1)
mality power source is also checked. An to turn OFF the
abnormal signal condition occurs RL1 (main).
a specified period of time after
FM12 is turned ON. This abnormal
condition recurs even a specified
period of time after FM12 is turned
OFF and then turned ON, and an
error detection signal (24V cut off)
is detected.
SC32-02 The blowout of a fuse for the IPB AC drive board (ACDB)
cooling fan (FM12) in the AC drive IPB cooling fan (FM12)
board (ACDB) is checked.
An abnormal condition occurs
with the FM12 EM signal a speci-
fied period of time after FM12 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM12 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-03 The rotation of the IPB cooling fan
(FM12) is checked.
An abnormal condition occurs
with the FM12 EM signal a speci-
fied period of time after FM12 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM12 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
SC32-04 When the print is started, the EM Error code is not AC drive board (ACDB)
signal of the PB cooling fan displayed on the IPB cooling fan (FM12)
(FM12) turns ON. operation panel,
but displayed only
on the data collec-
tion, the list output
and the CSRC.
The control of the
main body is
made by using a
data previously
obtained.
577
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
578
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- ration suction fan (FM4) is stops immediately 1)
mality checked, and the 24V power to turn OFF the
source is also checked. RL1 (main).
An abnormal condition occurs
with the FM4 EM signal a specified
period of time after FM4 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM4 is turned OFF and
then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-10 The blowout of a fuse for the Transfer/separation suction
transfer/separation suction fan fan (FM4)
(FM4) in the printer control board Printer control board (PRCB)
(PRCB) is checked.
An abnormal condition occurs
with the FM4 EM signal a specified
period of time after FM4 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM4 is turned OFF and
then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-11 The rotation of the transfer/sepa- Transfer/separation suction
ration suction fan (FM4) is fan (FM4)
checked. Printer control board (PRCB)
An abnormal condition occurs
with the FM4 EM signal a specified
period of time after FM4 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM4 is turned OFF and
then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
579
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
580
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- ing fan /1 (FM9) is checked, and stops immediately 1)
mality the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM9 EM signal a specified
period of time after FM9 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM9 is turned OFF and
then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-16 The blowout of a fuse for the Paper exit cooling fan /1
paper exit cooling fan /1 (FM9) in (FM9)
the printer control board (PRCB) is Printer control board (PRCB)
checked.
An abnormal condition occurs
with the FM9 EM signal a specified
period of time after FM9 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM9 is turned OFF and
then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-17 The rotation of the paper exit cool- Paper exit cooling fan /1
ing fan /1 (FM9) is checked. (FM9)
An abnormal condition occurs Printer control board (PRCB)
with the FM9 EM signal a specified
period of time after FM9 is turned
ON. This abnormal condition
recurs even a specified period of
time after FM9 is turned OFF and
then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
581
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
582
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- assist fan /Fr1 (FM20) is checked, stops immediately 1)
mality and the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM20 EM signal a speci-
fied period of time after FM20 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM20 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-22 The blowout of a fuse for the Paper feed assist fan /Fr1
paper feed assist fan /Fr1 (FM20) (FM20)
in the printer control board (PRCB) Printer control board (PRCB)
is checked.
An abnormal condition occurs
with the FM20 EM signal a speci-
fied period of time after FM20 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM20 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-23 The rotation of the paper feed Paper feed assist fan /Fr1
assist fan /Fr1 (FM20) is checked. (FM20)
An abnormal condition occurs Printer control board (PRCB)
with the FM20 EM signal a speci-
fied period of time after FM20 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM20 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
583
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
584
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- assist fan /Fr2 (FM22) is checked, stops immediately 1)
mality and the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM22 EM signal a speci-
fied period of time after FM22 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM22 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-28 The blowout of a fuse for the Paper feed assist fan /Fr2
paper feed assist fan /Fr2 (FM22) (FM22)
in the printer control board (PRCB) Printer control board (PRCB)
is checked.
An abnormal condition occurs
with the FM22 EM signal a speci-
fied period of time after FM22 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM22 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected.
SC32-29 The rotation of the paper feed Paper feed assist fan /Fr2
assist fan /Fr2 (FM22) is checked. (FM22)
An abnormal condition occurs Printer control board (PRCB)
with the FM22 EM signal a speci-
fied period of time after FM22 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM22 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
585
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
586
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- assist fan /Fr1 (FM41) is checked, stops immediately 2)
mality and the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM41 EM signal a speci-
fied period of time after FM41 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM41 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-34 The blowout of a fuse for the Paper feed assist fan /Fr1
paper feed assist fan /Fr1 (FM41) (FM41)
in the printer control board (PRCB) PF drive board (PFUDB)
is checked.
An abnormal condition occurs
with the FM41 EM signal a speci-
fied period of time after FM41 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM41 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-35 The rotation of the paper feed Paper feed assist fan /Fr1
assist fan /Fr1 (FM41) is checked. (FM41)
An abnormal condition occurs PF drive board (PFUDB)
with the FM41 EM signal a speci-
fied period of time after FM41 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM41 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
587
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
588
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- assist fan /Fr2 (FM43) is checked, stops immediately 2)
mality and the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM43 EM signal a speci-
fied period of time after FM43 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM43 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-40 The blowout of a fuse for the Paper feed assist fan /Fr2
paper feed assist fan /Fr2 (FM43) (FM43)
in the printer control board (PRCB) PF drive board (PFUDB)
is checked.
An abnormal condition occurs
with the FM43 EM signal a speci-
fied period of time after FM43 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM43 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-41 The rotation of the paper feed Paper feed assist fan /Fr2
assist fan /Fr2 (FM43) is checked. (FM43)
An abnormal condition occurs PF drive board (PFUDB)
with the FM43 EM signal a speci-
fied period of time after FM43 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM43 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
589
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
590
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- assist fan /Fr3 (FM45) is checked, stops immediately 2)
mality and the 24V power source is also to turn OFF the
checked. RL1 (main).
An abnormal condition occurs
with the FM45 EM signal a speci-
fied period of time after FM45 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM45 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-46 The blowout of a fuse for the Paper feed assist fan /Fr3
paper feed assist fan /Fr3 (FM45) (FM45)
in the printer control board (PRCB) PF drive board (PFUDB)
is checked.
An abnormal condition occurs
with the FM45 EM signal a speci-
fied period of time after FM45 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM45 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-47 The rotation of the paper feed Paper feed assist fan /Fr3
assist fan /Fr3 (FM45) is checked. (FM45)
An abnormal condition occurs PF drive board (PFUDB)
with the FM45 EM signal a speci-
fied period of time after FM45 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM45 is turned OFF
and then turned ON, and no error
detection signal (24V cut off/blow-
out of a fuse) is detected.
591
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
592
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- (FM20) is checked, and the 24V stops immediately 2)
mality power source is also checked. to turn OFF the
An abnormal condition occurs RL1 (main).
with the FM46 EM signal a speci-
fied period of time after FM46 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM46 is turned OFF
and then turned ON, and an error
detection signal (24V cut off) is
detected.
SC32-52 The blowout of a fuse for the cool- Cooling fan (FM20)
ing fan (FM20) in the printer con- PF drive board (PFUDB)
trol board (PRCB) is checked.
An abnormal condition occurs
with the FM46 EM signal a speci-
fied period of time after FM46 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM46 is turned OFF
and then turned ON, and an error
detection signal (blowout of a
fuse) is detected with the 24V nor-
mal.
SC32-53 The rotation of the cooling fan
Main body
(FM20) is checked.
An abnormal condition occurs
with the FM46 EM signal a speci-
fied period of time after FM46 is
turned ON. This abnormal condi-
tion recurs even a specified period
of time after FM46 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
593
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
594
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
sec- motor in the ADU drive board /1 stops immediately (ADUDB1)
tion (ADUDB1) is checked. to turn OFF the Reverse/exit motor (M13)
motor An error detection signal (blowout RL1 (main). ADU accelerate motor (M14)
abnor- of a fuse) of the reverse/exit motor ADU conveyance motor /1
mality (M13)/ADU acceleration motor (M15)
(M14)/ ADU conveyance motor /1 ADU reverse motor (M12)
(M15)/ADU reverse motor (M12) is
detected after the print is started.
At this time, the closing of the
door detection/PFU door is
detected 10 times in succession.
SC33-04 The blowout of a fuse for the Printer control board (PRCB)
transfer assist motor (M19) in the Transfer assist motor (M19)
printer control board (PRCB) is
checked.
When M19 turns ON from OFF, an
error detection signal (blowout of a
fuse) is detected. At this time, the
closing of the door is detected 10
times in succession.
SC33-05 The blowout of a fuse for the web DC power supply /2 (DCPS/
motor (M24) in the printer control 2)
board (PRCB) is checked, and the
24V power source is also
checked.
When M24 turn ON from OFF,
error detection signals (blowout of
a fuse and the 24V cut off) are
detected.
SC33-06 The blowout of a fuse for the web Printer control board (PRCB)
motor (M24) in the printer control Web motor (M24)
board (PRCB) is checked.
When M24 turns ON from OFF, an
error detection signal (blowout of a
fuse) is detected. At this time, an
error detection signal (24V cut off)
is not detected.
595
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
high tem- ture detection (software). stops immediately AC drive board (ACDB)
perature TH1 detects a temperature of to turn OFF the Fusing heater lamp /1 (L2)
abnor- 210°C or above 5 times in a RL1 (main). Fusing heater lamp /2 (L3)
mality period of 1 second. Fusing heater lamp /3 (L4)
SC34-02 Thermistor /3 (TH3) high tempera- Thermistor /1 (TH1)
ture detection (software). Thermistor /2 (TH2)
TH3 detects a temperature of Thermistor /3 (TH3)
230°C or above 5 times in a Thermistor /4 (TH4)
period of 1 second. Caution:
SC34-03 Thermistor /1 (TH1) high tempera- • When SC34-**, SC35-
ture detection (hardware). ** or SC36-** (fusing
An abnormal condition is detected temperature related
with the fusing error detection sig- abnormalities) occur,
nal 1. be sure to repair
defective parts before
SC34-04 Thermistor /3 (TH3) high tempera-
setting the software
ture detection (hardware). An
DIPSW3-1 to 0. Set-
abnormal condition is detected
ting the DIPSW3-1 to
with the fusing error detection sig-
0 with defective parts
nal 4.
not repaired may
Fusing SC35-01 Thermistor /1 (TH1) low tempera-
result in a fire.
low tem- ture detection (software). TH1
perature does not get to 50°C when a
abnor- specified period of time elapses
mality after the main switch (SW1) is
turned ON for the fusing ON con-
trol.
SC35-02 Thermistor /3 (TH3) low tempera-
ture detection (software). TH3
does not get to 50°C when a
specified period of time elapses
after the main switch (SW1) is
turned ON for the fusing ON con-
trol.
Fusing SC36-01 Thermistor /1 (TH1) high tempera-
sensor ture detection (long time/soft-
abnor- ware). TH1 detects a temperature
mality of 200°C or above 30 times in a
row in a period of 1 second.
SC36-02 Thermistor /3 (TH3) high tempera-
ture detection (long time/soft-
ware). TH3 detects a temperature
of 220°C or above 30 times in a
row in a period of 1 second.
596
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
sensor ture detection (hardware). TH1 stops immediately AC drive board (ACDB)
abnor- detects an abnormal condition to turn OFF the Fusing heater lamp /1 (L2)
mality with the fusing error detection sig- RL1 (main). Fusing heater lamp /2 (L3)
nal 2. Fusing heater lamp /3 (L4)
SC36-04 Thermistor /1 (TH1) low tempera- Thermistor /1 (TH1)
ture detection (hardware). TH3 Thermistor /2 (TH2)
detects an abnormal condition Thermistor /3 (TH3)
with the fusing error detection sig- Thermistor /4 (TH4)
nal 5. Caution:
SC36-05 Thermistor /3 (TH3) low tempera- • When SC34-**, SC35-
ture detection (hardware). TH1 ** or SC36-** (fusing
detects an abnormal condition temperature related
with the fusing error detection sig- abnormalities) occur,
nal 3. be sure to repair
defective parts before
SC36-06 Thermistor /3 (TH3) low tempera-
setting the software
ture detection (hardware). TH3
DIPSW3-1 to 0. Set-
detects an abnormal condition
ting the DIPSW3-1 to
with the fusing error detection sig-
0 with defective parts
nal 6.
not repaired may
result in a fire.
Scanner SC41-01 It is checked that the movement DC power supply /1 (DCPS/
abnor- time for the scanner motor (M27) 1)
mality is over, and the 24V power source
is also checked. The scanner
home sensor (PS51) or the APS
sensor /1 (PS52) does not turn
ON within a specified period of
time after the home position
search is started. And an error
detection signal (24V cut off) is
detected with the scanner motor
(M27).
SC41-02 The blowout of a fuse for the Scanner drive board (SDB)
scanner motor (M27) in the scan- Scanner motor (M27)
ner drive board (SDB) is checked.
The scanner home sensor (PS51)
or the APS sensor /1 (PS52) does
not turn ON within a specified
period of time after the home posi-
tion search is started. And an error
detection signal (blowout of a
fuse) is detected with M27. At this
time, an error detection signal
(24V cut off) is not detected with
the M27.
2 597
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- scanner motor (M27) is over. The stops immediately Scanner motor (M27)
mality scanner home sensor (PS51) or to turn OFF the Scanner home sensor
the APS sensor /1 (PS52) does RL1 (main). (PS51)
not turn ON within a specified
period of time after the home posi-
tion search is started. And an error
detection signal (blowout of a
fuse/24V cut off) is not detected
with the M27.
Write SC41-10 The abnormal speed of the poly- DC power supply /1 (DCPS/
abnor- gon motor (M21) is checked, and 1)
mality the 24V power source is also
checked. When switching the
speed of M21, the lock signal of
M21 is not detected within a
specified period of time after the
switchover is started, and an error
detection signal (24V cut off) is
detected.
SC41-11 The abnormal speed of the poly- Polygon motor (M21)
gon motor (M21) is checked. Printer control board (PRCB)
When switching the speed of
M21, the lock signal of M21 is not
detected within a specified period
of time after the switchover is
started.
Fan SC42-01 The rotation of the scanner cool- DC power supply /2 (DCPS/
abnor- ing fan (FM19) is checked, and 2)
mality 24V power source is also
checked. An abnormal condition
occurs with the FM19 EM signal a
specified period of time after
FM19 turns ON. This abnormal
condition recurs even a specified
period of time after FM19 is turned
OFF and then turned ON, and an
error detection signal (24V cut off)
is detected.
598
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- scanner cooling fan (FM19) in the stops immediately Scanner cooling fan (FM19)
mality scanner drive board (SDB) is to turn OFF the
checked. An abnormal condition RL1 (main).
occurs with the FM19 EM signal a
specified period of time after
FM19 turns ON. This abnormal
condition recurs even a specified
period of time after FM19 is turned
OFF and then turned ON, and an
error detection signal (blowout of a
fuse) is detected. At this time, an
error detection signal (24V cut off)
is not detected.
SC42-03 The rotation of the scanner cool- Scanner cooling fan (FM19)
ing fan (FM19) is checked. An
abnormal condition occurs with
the FM19 EM signal a specified
period of time after FM19 turns
ON. This abnormal condition
recurs even a specified period of
time after FM19 is turned OFF and
then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
SC42-04 The rotation of the suction fan /1 DC power supply /2 (DCPS/
(FM6) is checked, and 24V power 2)
source is also checked. An abnor-
mal condition occurs with the FM6
EM signal a specified period of
time after FM6 turns ON. This
abnormal condition recurs even a
specified period of time after FM6
is turned OFF and then turned
ON, and an error detection signal
(24V cut off) is detected.
599
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- tion fan /1 (FM6) in the AC drive stops immediately Suction fan /1 (FM6)
mality board (ACDB) is checked. An to turn OFF the
abnormal condition occurs with RL1 (main).
the FM6 EM signal a specified
period of time after FM6 turns ON.
This abnormal condition recurs
even a specified period of time
after FM6 is turned OFF and then
turned ON, and an error detection
signal (blowout of a fuse) is
detected. At this time, an error
detection signal (24V cut off) is not
detected.
SC42-06 The rotation of the suction fan /1
(FM6) is checked. An abnormal
condition occurs with the FM6 EM
signal a specified period of time
after FM6 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM6 is
turned OFF and then turned ON,
and an error detection signal (24V
cut off/blowout of a fuse) is not
detected.
SC42-07 The EM signal of the suction fan /1 Suction fan /1 (FM6)
(FM6) is ON when the printing is
started.
SC42-08 The rotation of the suction fans /2 DC power supply /2 (DCPS/
(FM7) and /3 (FM8) is checked, 2)
and the 24V power source is also
checked. An abnormal condition
occurs with the FM7/FM8 EM sig-
nal a specified period of time after
FM7/FM8 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM7/FM8
is turned OFF and then turned
ON, and an error detection signal
(24V cut off) is detected.
600
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- tion fans /2 (FM7) and /3 (FM8) in stops immediately Suction fan /2 (FM7)
mality the AC drive board (ACDB) is to turn OFF the Suction fan /3 (FM8)
checked. An abnormal condition RL1 (main).
occurs with the FM7/FM8 EM sig-
nal a specified period of time after
FM7/FM8 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM7/FM8
is turned OFF and then turned
ON, and an error detection signal
(blowout of a fuse) is detected. At
this time an error detection signal
(24V cut off) is not detected.
SC42-10 The rotation of the suction fans /2
(FM7) and /3 (FM8) is checked. An
abnormal condition occurs with
the FM7/FM8 EM signal a speci-
fied period of time after FM7/FM8
turns ON. This abnormal condition
recurs even a specified period of
time after FM7/FM8 is turned OFF
and then turned ON, and an error
detection signal (24V cut off/blow-
out of a fuse) is not detected.
SC42-16 The rotation of the polygon cool- DC power supply /2 (DCPS/
ing fan (FM18) is checked, and the 2)
24V power source is also
checked. An abnormal condition
occurs with the FM18 EM signal a
specified period of time after
FM18 turns ON. This abnormal
condition recurs even a specified
period of time after FM18 is turned
OFF and then turned ON, and an
error detection signal (24V cut off)
is detected.
601
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- gon cooling fans (FM18) in the AC stops immediately Polygon cooling fan (FM18)
mality drive board (ACDB) is checked. to turn OFF the
An abnormal condition occurs RL1 (main).
with the FM18 EM signal a speci-
fied period of time after FM18
turns ON. This abnormal condition
recurs even a specified period of
time after FM18 is turned OFF and
then turned ON, and an error
detection signal (blowout of a
fuse) is detected. At this time, an
error detection signal (24V cut off)
is not detected.
SC42-18 Rotation of the polygon cooling
fans (FM18) is checked. An abnor-
mal condition occurs with the
FM18 EM signal a specified period
of time after FM18 turns ON. This
abnormal condition recurs even a
specified period of time after
FM18 is turned OFF and then
turned ON, and an error detection
signal (24V cut off/blowout of a
fuse) is not detected.
SC42-19 The EM signal of the polygon Error code is not Polygon cooling fan (FM18)
cooling fan (FM18) is ON when the displayed on the
printing is started. operation panel,
but displayed only
on the data collec-
tion, the list output
and the CSRC.
The control of the
main body is
made by using a
data previously
obtained.
602
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
pro- image write, APC is not applicable being made, the Power connector of the
cess- for the correction of the sub scan main body com- image processing board
ing beam. Due to the 12V DC power pletes the paper (IPB)
abnor- for the laser drive not supplied, the exit before stop-
mality MPC being wrong and the laser ping operations.
defective, the laser does not light Turn OFF the RL1
up. (main).
Also, due to the rotation of the
polygon mirror unavailable, the
displacement of the index sensor,
and the index sensor being defec-
tive, the index sensor cannot
detect the laser.
SC46-02* Scanner FIFO abnormality. FIFO Image processing board
address abnormality for the scan- (IPB)
ner.
While in the image read, the com-
pression of image data that is read
in is not correctly terminated.
SC46-03* FIFO address abnormality for the
printer.
While in the image write, the
expansion processing of image
data that is read in is not correctly
terminated.
SC46-05* Compression input FIFO abnor-
mality. An error interrupt occurs
with the compression/expansion
chip FIFO.
SC46-06* Elongation abnormality. Due to the
elongation of data the compres-
sion of which is not completed,
the destruction of the compressed
data and the abnormal length of
data, an elongation abnormality is
detected.
SC46-08* Index sensor abnormality. While in Write unit
the execution of APC, no change Power connector of the
is found in the output of the index image processing board
sensor. (IPB)
SC46-12* SVV length abnormality. After Image processing board
negation of SVV, the compression (IPB)
of images that are read in and their
development into the page mem-
ory are not terminated within a
specified period of time.
603
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
pro- image read, the compression pro- being made, the (IPB)
cess- cessing from the scanner into the main body com- ADF
ing memory does not terminate within pletes the paper Printer control board (PRCB)
abnor- a specified period of time. The exit before stop-
mality development from the scanner ping operations.
into the page memory does not Turn OFF the RL1
terminate within a specified period (main).
of time. The SVV is not detected
within a specified period of time.
SC46-14* Printer time out. While in the Image processing board
image write, the expansion pro- (IPB)
cessing from the memory to the Printer control board (PRCB)
printer does not terminate within a
specified period of time.
The output from the page memory
to the printer does not terminate
within a specified period of time.
The PVV is not detected within a
specified period of time.
SC46-15* Expansion device access abnor- Image processing board
mality. While in the image write, (IPB)
despite of no resource provided, Image processing program
an inappropriate processing such
as accessing to the elongation
device is made.
SC46-16* Compression device access
abnormality. When writing images,
in spite of no resource provided,
an inappropriate processing such
as an access to the compression
device is made.
SC46-17* Filter coefficient abnormality.
When processing images, a filter
coefficient cannot be created nor-
mally.
SC46-19* When accessing to the memory
device, a defective software is
detected.
604
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
pro- processing from the memory to being made, the (IPB)
cess- the pate memory is not terminated main body com- Image processing program
ing within a specified period of time. pletes the paper Printer control board (PRCB)
abnor- The compression processing from exit before stop-
mality the page memory to the memory ping operations.
is not terminated within a specified Turn OFF the RL1
period of time. (main).
The development from the mem-
ory into the page memory is not
terminated within a specified
period of time. The transmission of
the compressed data from mem-
ory to memory is not terminated
within a specified period of time.
SC46-23* SVV off abnormality. While in the Image processing board
image read, SVV does not turn (IPB)
OFF within a specified period of
time and the preparation for scan-
ning the next page cannot be
started.
SC46-24* Shading correction abnormality Image processing board
(GA abnormality). (IPB)
SC46-25* AOC/AGC adjustment level abnor- Image processing program
mality.
• The light blocking cover at the
read section and the lens
cover are removed.
• The connector of the A/D con-
verter board is disconnected.
• The power cable of the A/D
converter board is unplugged.
• The IC protector of the A/D
converter board is cut off.
• The light volume of the expo-
sure lamp is excessive.
• The exposure lamp does not
light up.
605
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
606 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
pro- the original skew adjustment is displayed on the Original skew sensor /Fr
cess- terminated. (The skew adjustment operation panel, (PS312), /Rr (PS311)
ing is too late.) but displayed only
abnor- SC46-62 The print operation starts before on the data collec- Centering sensor (PS54)
mality the paper mis-centering adjust- tion, the list output
ment is terminated. (The mis-cen- and the CSRC.
tering adjustment is too late.) The control of the
SC46-63 The AGC is retried due to the main body is Exposure lamp (L1)
decreased light volume of the made by using a
exposure lamp. However, no error data previously
occurs. obtained.
SC46-64 A PWM gamma curve is not cre- Toner control sensor board
ated properly. (TCSB)
SC46-66 Shift amount abnormality while in
the repeat (when the width is
specified, or in the auto mode).
When the shift amount while in the
repeat is negative (-).
SC46-80* The message queue is insufficient If there is a copy Image processing program
or destroyed. being made, the
SC46-81* The parameter value is in excess main body com- Image processing board
of the permissible limits. pletes the paper (IPB)
SC46-82* The ID of the task that sends the exit before stop-
message queue is undefined. ping operations.
Turn OFF the RL1
SC46-83* The receiving event of the mes-
(main).
sage is undefined.
SC46-90* Memory access abnormality.
SC46-91* Header readout address abnor-
mality.
SC46-99* DIMM memory abnormality. An
error is detected in the DIMM
memory check at the start.
IC SC49-01 Printer controller initial communi- The main body IC board (ICB)
Con- cation abnormality stops immediately Hard disk /2 (HDD2)
troller SC49-03 Transfer error to the main body to turn OFF the IC board (ICB)
abnor- image memory RL1 (main).
mality SC49-04 Hard disc /2 (HDD2) abnormality IC board (ICB)
Hard disk /2 (HDD2)
SC49-05 IC cooling fan (FM24) lock abnor- IC board (ICB)
mality
SC49-06 Unregulations IP error. –
SC49-07 The CF version is different from Hard disk /2 (HDD2)
the version information in the hard format HDD2
disc /2 (HDD2).
2 607
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Con- unlock of the HDD results in a fail- stops immediately format HDD2
troller ure due to the mismatched pass- to turn OFF the
abnor- word of the hard disk /2 (HDD2). RL1 (main).
mality SC49-09 Unlocked hard disk/2 (HDD2) is
detected when security turns ON.
SC49-10 An unformatted hard disc /2
(HDD2) is detected.
Drive SC50-01* Main body drive serial input abnor- Printer control board (PRCB)
abnor- mality 1. PF drive board (PFUDB)
mality In the I/O initial communication The connector between the
check in the printer control board PF and the main body.
(PRCB) from the power on ACK, a
serial data is not received from the
main body drive unit within a
specified period of time.
SC50-02* Main body drive serial input abnor-
mality 2.
In the I/O initial communication
check in the printer control board
(PRCB) from the power on ACK, a
serial data is not received from the
main body drive unit within a
specified period of time.
SC50-03* Main body drive serial input abnor-
mality 3.
In the I/O initial communication
check in the printer control board
(PRCB) from the power on ACK, a
serial data is not received from the
main body drive unit within a
specified period of time.
SC50-04* Main body drive serial input abnor-
mality 4.
In the I/O initial communication
check in the printer control board
(PRCB) from the power on ACK, a
serial data is not received from the
main body drive unit within a
specified period of time.
Commu- SC50-05* Drive communication reception
nication error detection abnormality.
abnor- SC50-06* Drive communication reception Printer control board (PRCB)
mality error detection abnormality.
SC50-07* Drive communication reception
error detection abnormality.
608 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
nication error detection abnormality. stops immediately
abnor- SC50-10 When the power switch is turned to turn OFF the Printer control board (PRCB)
mality ON, the printer control board RL1 (main). Image processing board
(PRCB) cannot receive initial data (IPB)
from the image processing board
(IPB) within a specified period of
time.
SC50-11 Any of the following error is Printer control board (PRCB)
detected during data reception Image processing board
between image processing board (IPB)
(IPB) and printer control board The connector between the
(PRCB). PRDB and the IPB.
• Data head error
• Data checksum error
• Undefined command recep-
tion error
• Occurrence of communica-
tion GA error vector
SC51-01* Drive communication reception Printer control board (PRCB)
error detection abnormality. PF drive board (PFUDB)
SC51-02* Drive communication reception The connector between the
error detection abnormality. PF and the main body.
SC51-03* Drive communication reception
error detection abnormality.
Fan SC52-01 The rotation of the cooling fan /1 DC power supply /2 (DCPS/
abnor- (FM1) is checked, and +24V 2)
mality power source is also checked. An
abnormal condition occurs with
the FM1 EM signal a specified
period of time after FM1 turns ON.
This abnormal condition recurs
even a specified period of time
after FM1 is turned OFF and then
turned ON, and an error detection
signal (24V cut off) is detected.
2 609
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- ing fan /1 (FM1) in the AC drive stops immediately Cooling fan /1 (FM1)
mality board (ACDB) is checked. An to turn OFF the Printer control board (PRCB)
abnormal condition occurs with RL1 (main).
the FM1 EM signal a specified
period of time after FM1 turns ON.
This abnormal condition recurs
even a specified period of time
after FM1 is turned OFF and then
turned ON, and an error detection
signal (blowout of a fuse) is
detected. At this time, an error
detection signal (24V cut off) is not
detected.
SC52-03 Rotation of the cooling fan /1 AC drive board (ACDB)
(FM1) is checked. An abnormal Cooling fan /1 (FM1)
condition occurs with the FM1 EM Printer control board (PRCB)
signal a specified period of time
after FM1 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM1 is
turned OFF and then turned ON,
and an error detection signal (24V
cut off/blowout of a fuse) is not
detected.
SC52-04 The rotation of the cooling fan /2 DC power supply /2 (DCPS/
(FM2) is checked, and +24V 2)
power source is also checked. An
abnormal condition occurs with
the FM2 EM signal a specified
period of time after FM2 turns ON.
This abnormal condition recurs
even a specified period of time
after FM2 is turned OFF and then
turned ON, and an error detection
signal (24V cut off) is detected.
610
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- ing fan /2 (FM2) in the AC drive stops immediately Cooling fan /2 (FM2)
mality board (ACDB) is checked. An to turn OFF the Printer control board (PRCB)
abnormal condition occurs with RL1 (main).
the FM2 EM signal a specified
period of time after FM2 turns ON.
This abnormal condition recurs
even a specified period of time
after FM2 is turned OFF and then
turned ON, and an error detection
signal (blowout of a fuse) is
detected. At this time, an error
detection signal (24V cut off) is not
detected.
SC52-06 Rotation of the cooling fan /2 AC drive board (ACDB)
(FM2) is checked. An abnormal Cooling fan /2 (FM2)
condition occurs with the FM2 EM Printer control board (PRCB)
signal a specified period of time
after FM2 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM2 is
turned OFF and then turned ON,
and an error detection signal (24V
cut off/blowout of a fuse) is not
detected.
SC52-07 The rotation of the cooling fan /3 DC power supply /2 (DCPS/
(FM3) is checked, and +24V 2)
power source is also checked. An
abnormal condition occurs with
the FM3 EM signal a specified
period of time after FM3 turns ON.
This abnormal condition recurs
even a specified period of time
after FM3 is turned OFF and then
turned ON, and an error detection
signal (24V cut off) is detected.
611
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- ing fan /3 (FM3) in the AC drive stops immediately Cooling fan /3 (FM3)
mality board (ACDB) is checked. An to turn OFF the Printer control board (PRCB)
abnormal condition occurs with RL1 (main).
the FM3 EM signal a specified
period of time after FM3 turns ON.
This abnormal condition recurs
even a specified period of time
after FM3 is turned OFF and then
turned ON, and an error detection
signal (blowout of a fuse) is
detected. At this time, an error
detection signal (24V cut off) is not
detected.
SC52-09 Rotation of the cooling fan /3 AC drive board (ACDB)
(FM3) is checked. An abnormal Cooling fan /3 (FM3)
condition occurs with the FM3 EM Printer control board (PRCB)
signal a specified period of time
after FM3 turns ON. This abnor-
mal condition recurs even a speci-
fied period of time after FM3 is
turned OFF and then turned ON,
and an error detection signal (24V
cut off/blowout of a fuse) is not
detected.
SC52-10 The EM signal of the cooling fan /1 Error code is not Cooling fan /1 (FM1)
(FM1) is ON when the print is displayed on the
started. operation panel,
SC52-11 The EM signal of the cooling fan /2 but displayed only Cooling fan /2 (FM2)
(FM2) is ON when the print is on the data collec-
started. tion, the list output
SC52-12 The EM signal of the cooling fan /3 and the CSRC. Cooling fan /3 (FM3)
(FM3) is ON when the print is The control of the
started. main body is
made by using a
data previously
obtained.
Power SC53-01 A speed error signal of the fusing The main body Fusing motor (M1)
abnor- motor (M1) is checked. An error stops immediately
mality detection signal is detected twice to turn OFF the
in succession a specified period of RL1 (main).
time after M1 turns ON. (The first
signal is ignored.)
612
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- counter (CNT1) is checked. When stops immediately 2)
mality CNT1 is turned ON from OFF, an to turn OFF the
error detection signal (blowout of a RL1 (main).
fuse/24V cut off) is detected.
SC53-03 The blowout of a fuse for the total Main relay (RL1)
counter (CNT1) in the AC drive Total counter (CNT1)
board (ACDB) is checked. When AC drive board (ACDB)
CNT1 is turned ON from OFF, an
error detection signal (blowout of a
fuse) is detected. However, an
error detection signal (24V cut off)
is not detected.
SC53-04 The 24V power source for the key DC power supply /2 (DCPS/
counter (CNT2) is checked. When 2)
CNT2 is turned ON from OFF, an
error detection signal (blowout of a
fuse/24V cut off) is detected.
SC53-05 The blowout of a fuse for the key Key counter (CNT2)
counter (CNT2) in the AC drive
board (ACDB) is checked. When
CNT2 is turned ON from OFF, an
error detection signal (blowout of a
fuse) is detected. However, an
error detection signal (24V cut off)
is not detected.
SC53-06 The blowout of a 12V fuse for the AC drive board (ACDB)
AC drive board (ACDB) is
checked. In the serial initial com-
munication, a signal of the blow-
out of a 12V fuse (AC drive) is
detected.
SC53-07 The blowout of a 5V fuse for the
AC drive board (ACDB) is
checked. In the serial initial com-
munication, a signal of the blow-
out of a 5V fuse (AC drive) is
detected.
SC53-08 The 12V power source in the DC power supply /1 (DCPS/
printer control board (PRCB) is 1)
checked. An error detection signal Printer control board (PRCB)
of the 12V in PRCB is detected.
613
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
614
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- the PF is detected 1. The 24V stops immediately
mality power source for SD/CL in the PF to turn OFF the
drive board (PFUCB) is checked. RL1 (main).
At the start, an error detection sig-
nal (blowout of a fuse for the sole-
noid/clutch) is detected, and an
error detection signal (24V cut off)
is detected.
SC53-16 The blowout of a fuse for SD/CL in
the PF is detected 2. The blowout
of a fuse for SD/CL in the PF drive
board (PFUDB) is checked. At the
start, an error detection signal
(blowout of a fuse for the solenoid/
motor) is detected. However, an
error detection signal (24V cut off)
is not detected.
SC53-17 The blowout of the sensor 5VICP Printer control board (PRCB)
is detected. An error detection
signal of the blowout of the 5VICP
is detected.
SC53-18 The fall-off of the erase lamp (EL) The main body Erase lamp (EL)
CN is detected. When turning ON stops immediately
the power, an error detection sig- to turn OFF the
nal (fall-off) is detected a specified RL1 (main).
period of time after the fall-off
detection control signal of the EL
CN turns ON.
SC53-19 An M5 EM error detection signal is Conveyance motor (M5)
detected twice in succession a Printer control board (PRCB)
specified period of time after the
conveyance motor (M5) turns ON.
SC53-20 An M31 EM error detection signal ADU reverse paper exit
is detected twice in succession a motor (M31)
specified period of time after the Printer control board (PRCB)
ADU reverse/exit motor (M31)
turns ON.
SC56-02 The communication between the Operation board /1 (OB1)
image processing board (IPB) and Overall control board
the operation board /1 (OB1) is (OACB)
checked. An initial communica-
tion from the main body to the
operation board is not sent within
30 seconds after the power is
turned ON.
615
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- data according to the data trans- being made, the (IPB)
mality mission request by the DF, the main body and the
same request is received again. DF complete the
SC60-02* When a checksum error or an paper exit before RADF control board
SRGA reception error was stopping opera- (ADFCB)
detected while in the reception in tions. Turn OFF
serial communication, a signal the RL1 (main).
was sent to make a request for
sending data again. And when
data is being received upon this
request, a checksum error or an
SRGA reception error is detected
again.
SC60-03* When the main power switch RADF control board
(SW1) is ON, there is no response (ADFCB)
to the initial communication
request from the main body to the
DF even after a specified period of
time elapses.
SC60-11 When the main power switch RADF control board
(SW1) is ON, a region into which (ADFCB)
no write was made by the ISW is RADF program
detected in the DF control pro-
gram.
SC67-01 Original registration sensor /Rt If there is a copy Original registration sensor /
(PS306) abnormality. being made, the Rt (PS306)
SC67-02 Original conveyance sensor main body com- Original conveyance sensor
(PS308) abnormality. pletes the paper (PS308)
SC67-03 Original reverse sensor (PS309) exit before stop- Original reverse sensor
abnormality. ping operations. (PS309)
Turn OFF the RL1
SC67-04 Non-volatile memory error RADF control board
(main).
(ADFCB)
SC67-05 Cooling fan /Lt (FM301) abnormal- Cooling fan /Lt (FM301)
ity.
SC67-06 Original reverse sensor (PS309) Original reverse sensor
abnormality. (PS309)
SC67-07 Original reverse/exit sensor Original reverse/exit sensor
(PS313) abnormality. (PS313)
SC67-08 Tray up/down motor (M303) Tray up/down motor (M303)
abnormality.
SC67-09 Original skew sensor /Fr (PS312) Original skew sensor /Fr
abnormality. (PS312)
SC67-10 Original skew sensor /Rr (PS311) Original skew sensor /Rr
abnormality. (PS311)
616
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- (PS318) abnormality. being made, the Lt (PS318)
mality main body com-
SC67-12 Mis-centering sensor /Fr (PS320) pletes the paper Centering sensor /Fr
abnormality. exit before stop- (PS320)
SC67-13 Mis-centering sensor /Rr (PS321) ping operations. Centering sensor /Rr
abnormality. Turn OFF the RL1 (PS321)
(main).
SC67-14 Multi feed sensor /1 (MFS1) Multi feed sensor /1 (MFS1)
abnormality.
Commu- SC70-01 FS, FD, SD serial receive error. The main body , FNS control board (FNSCB)
FS, FD, SD
nication During re-transmission demand, the FS, The FD FD control board (FDCB)
abnor- either one of the error vector and the SD stop SD control board (SDCB)
mality occurrence or data checksum immediately to
error was continuously detected turn OFF the main
for specified time. relay (RL1).
SC70-02 FS, FD, SD start up response
error.
When there is no response to
operation starting order, even after
several retries.
LS SC76-01 The Stacker tray encoder sensor The main body Stacker tray up down motor
LS
abnor- (PS2) does not turn ON within a and the LS stop (M1)
mality specified period of time after the immediately to LS control board (LSCB)
stacker tray up down motor (M1) turn OFF the main
of the tandem (1st) LS turns ON. relay (RL1).
Or, the initial operation or the
stacker tray down operation is not
completed within a specified
period of time.
SC76-02 The shift unit home sensor (PS11) Shift unit motor (M5)
does not turn OFF within a speci- LS control board (LSCB)
fied period of time after the shift
unit motor (M5) of the tandem (1st)
LS turns ON. Or, PS11 does not
turn ON within a specified period
of time.
SC76-03 The alignment plate home sensor Alignment motor (M7)
(PS12) does not turn OFF within a LS control board (LSCB)
specified period of time after the
alignment motor (M7) of the tan-
dem (1st) LS turns ON. Or, PS12
does not turn ON within a speci-
fied period of time.
2 617
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
618
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- (PS2) does not turn ON a speci- and the LS stop (M1)
mality fied period of time after the immediately to LS control board (LSCB)
stacker tray up down motor (M1) turn OFF the main
of the tandem (2nd) LS turns ON. relay (RL1).
Or, the initial operation or the
stacker tray down operation is not
completed within a specified
period of time.
SC76-32 The shift unit home sensor (PS11) Shift unit motor (M5)
does not turn OFF within a speci- LS control board (LSCB)
fied period of time after the shift
unit motor (M5) of the tandem
(2nd) LS turns ON. Or, PS11 does
not turn ON within a specified
period of time.
SC76-33 The alignment plate home sensor Alignment motor (M7)
(PS12) does not turn OFF within a LS control board (LSCB)
specified period of time after the
alignment motor (M7) of the tan-
dem (2nd) LS turns ON. Or, PS12
does not turn ON within a speci-
fied period of time.
SC76-34 The grip conveyance home sensor Grip conveyance motor (M4)
(PS5) does not turn ON within a
specified period of time after the
grip conveyance motor (M4) of the
tandem (2nd) LS turns ON.
SC76-35 The stacker tray upper limit switch Stacker tray up down motor
(MS2) is ON when the stacker tray (M1)
up down motor (M1) of the tan- Stacker tray upper limit
dem (2nd) LS is in the up opera- switch (MS2)
tion.
SC76-36 The stacker tray lower limit switch Stacker tray up down motor
(MS3) is ON when the stacker tray (M1)
up down motor (M1) of the tan- Stacker tray lower limit
dem (2nd) LS is in the down oper- switch (MS3)
ation.
SC76-37 An error detection signal is Paper cooling fan motor /Fr
detected for a specified period of (FM1)
time in succession while the paper LS control board (LSCB)
cooling fan motor /Fr (FM1) of the
tandem (2nd) LS is ON.
619
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- detected for a specified period of and the LS stop /2 (FM2, FM6)
mality time in succession while the paper immediately to LS control board (LSCB)
cooling fan motor /1, /2 (FM2, turn OFF the main
FM6) of the tandem (2nd) LS is relay (RL1).
ON.
SC76-39 An error detection signal is Paper cooling fan motor /Mi
detected for a specified period of (FM3)
time in succession while the paper LS control board (LSCB)
cooling fan motor /Mi (FM3) of the
tandem (2nd) LS is ON.
SC76-40 An error detection signal is Motor cooling fan motor
detected for a specified period of (FM4)
time in succession while the motor LS control board (LSCB)
cooling fan motor (FM4) of the tan-
dem (2nd) LS is ON.
SC76-41 An error detection signal is Paper cooling fan motor /Rr
detected for a specified period of (FM5)
time in succession while the paper LS control board (LSCB)
cooling fan motor /Rr (FM5) of the
tandem (2nd) LS is ON.
FS SC77-01 The conveyance motor (M1) oper- The main body FNS control board (FNSCB)
FS
abnor- ates for more than the allowed and the FS stop FNS drive board (FNSDB)
mality time at a speed out of the speci- immediately to Conveyance motor (M1)
fied one. turn OFF the main
SC77-02 The tray up down motor (M3) relay (RL1). FNS control board (FNSCB)
does not turn OFF even when a FNS drive board (FNSDB)
specified period of time elapses Tray up down motor (M3)
after it starts operations. Or, it Tray upper limit sensor (PS2)
operates for more than the Tray lower limit sensor (PS3)
allowed time at a speed out of the
specified one.
SC77-03 The alignment home sensors /Rr FNS control board (FNSCB)
(PS8) and /Fr (PS31) do not turn FNS drive board (FNSDB)
ON within a specified period of Alignment motor /Rr (M5)
time after the home position Alignment motor /Fr (M22)
search operation of the alignment Alignment home sensor /Rr
motors /Rr (M5) and /Fr (M22) (PS8)
starts. Alignment home sensor /Fr
(PS31)
SC77-04 The main tray paper exit motor FNS control board (FNSCB)
(M7) operates for more than the FNS drive board (FNSDB)
allowed time at a speed out of the Main tray exit motor (M7)
specified one.
620
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- not get to the specified opening and the FS stop FNS drive board (FNSDB)
mality position within a specified period immediately to Paper exit opening motor
of time after the paper exit open- turn OFF the main (M8)
ing motor (M8) starts operations. relay (RL1). Paper exit opening sensor
(PS12)
SC77-06 The stapler movement home sen- FNS control board (FNSCB)
sor (PS11) does not turn ON FNS drive board (FNSDB)
within a specified period of time Stapler movement motor
after the home position search (M11)
operation of the stapler movement Stapler movement home
motor (M11) starts. sensor (PS11)
SC77-07 The stapler rotation home sensor FNS control board (FNSCB)
(PS14) does not turn ON within a FNS drive board (FNSDB)
specified period of time after the Stapler rotation motor (M4)
home position search operation of Stapler rotation home sen-
the stapler rotation motor (M4) sor (PS14)
starts.
SC77-08 The stapler rotation home sensor FNS control board (FNSCB)
(PS14) does not turn OFF within a FNS drive board (FNSDB)
specified period of time after the Stapler rotation motor (M4)
home position search operation of Stapler rotation home sen-
the stapler rotation motor (M4) sor (PS14)
starts.
SC77-11 After the stapler motor /Fr (M31) FNS control board (FNSCB)
starts operations, it does not com- FNS drive board (FNSDB)
plete operations within a specified Stapler board (SB)
period of time, and the stapler Stapler motor /Fr (M31)
home sensor /Fr (PS41) does not Stapler home sensor /Fr
turn ON. (PS41)
SC77-12 After the stapler motor /Rr (M30) FNS control board (FNSCB)
starts operations, it does not com- FNS drive board (FNSDB)
plete operations within a specified Stapler board (SB)
period of time, and the stapler Stapler motor /Rr (M30)
home sensor /Rr (PS40) does not Stapler home sensor /Rr
turn ON. (PS40)
SC77-15 After the paper exit arm motor FNS control board (FNSCB)
(M23) starts operations, it does FNS drive board (FNSDB)
not complete operations within a Paper exit arm motor (M23)
specified period of time, and the Paper exit arm home sensor
paper exit arm sensor (PS9) does (PS9)
not turn ON. Or, it operates for
more than the allowed time at a
speed out of the specified one.
621
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- operation of the rear stopper and the FS stop FNS drive board (FNSDB)
mality motor (M26) starts, the rear stop- immediately to Rear stopper motor (M26)
per home sensor (PS35) does not turn OFF the main Rear stopper home sensor
turn ON within a specified period relay (RL1). (PS35)
of time.
SC77-22 After the home position search FNS control board (FNSCB)
operation of the stack assist guide FNS drive board (FNSDB)
motor (M24) starts, the stack Stack assist guide motor
assist home sensor (PS32) does (M24)
not turn ON within a specified Stack assist home sensor
period of time. (PS32)
SC77-25 After the home position search FNS control board (FNSCB)
operation of the intermediate roller FNS drive board (FNSDB)
open close motor (M25) starts, the Intermediate roller open
intermediate roller home sensor close motor (M25)
(PS33) does not turn ON within a Intermediate roller home
specified period of time. sensor (PS33)
SC77-28 Data was resent according to the FNS control board (FNSCB)
re-dispatch request of communi-
cation data, but the error recurs.
FD SC77-30 After the 1st folding release motor The main body 1st folding release motor
FD
abnor- (M14) turns ON, the 1st folding and the FD stop (M14)
mality cam home sensor (PS55) does immediately to Folding drive board (FDB)
not turn ON within a specified turn OFF the main 1st folding cam home sen-
period of time. relay (RL1). sor (PS55)
SC77-31 After the 2nd folding release motor 2nd folding release motor
(M15) turns ON, the 2nd folding (M15)
cam home sensor (PS56) does Folding drive board (FDB)
not turn ON within a specified 2nd folding cam home sen-
period of time. sor (PS56)
SC77-32 After the 3rd folding release motor 3rd folding release motor
(M16) turns ON, the 3rd folding (M16)
cam home sensor (PS57) does Folding drive board (FDB)
not turn ON within a specified 3rd folding cam home sen-
period of time. sor (PS57)
SC77-33 The 2 holes punch home sensor Punch motor (M10)
(PS8) does not turn OFF within a Punch drive board (PDB)
specified period of time after the 2 2 holes punch home sensor
holes punch home position return (PS8)
operation starts. Or, after the
punch motor (M10) turns ON, the
2 holes punch home sensor (PS8)
does not turn OFF.
622
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- sensor (PS9) does not turn OFF and the FD stop Punch drive board (PDB)
mality within a specified period of time immediately to 3 holes/4 holes punch home
after the 3 holes/4 holes punch turn OFF the main sensor (PS9)
home position return operation relay (RL1).
starts. Or, after the punch motor
(M10) turns ON, the 3 holes/4
holes punch home sensor (PS9)
does not turn OFF.
SC77-35 The alignment plate home sensor Alignment motor (M12)
(PS10) does not turn ON within a Punch drive board (PDB)
specified period of time after the Alignment plate home sen-
alignment plate home position sor (PS10)
return operation starts. Or, after
the alignment motor (M12) turns
ON, the alignment plate home
sensor (PS10) does not turn OFF.
SC77-36 The punch registration home sen- Punch registration motor
sor (PS11) does not turn ON (M13)
within a specified period of time Punch drive board (PDB)
after the punch registration claw Punch registration home
home position return operation sensor (PS11)
starts. Or, after the punch registra-
tion motor (M13) turns ON, the
punch registration home sensor
(PS11) does not turn OFF.
SC77-37 The main tray upper limit sensor Tray up down motor (M11)
(PS20) does not turn ON within a Main tray upper limit sensor
specified period of time after the (PS20)
main tray home position search Punch drive board (PDB)
starts. Or, after the tray up down
motor (M11) turns ON, the main
tray upper limit sensor (PS20)
does not turn OFF.
SC77-38 The main tray lower limit sensor Tray up down motor (M11)
(PS22) does not turn ON within a Punch drive board (PDB)
specified period of time after the Main tray lower limit sensor
tray up down motor (M11) is in the (PS22)
down operation.
623
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- (M8) is in the down operation, the and the FD stop PI drive board (PIDB)
mality PI lift plate home sensor /Up immediately to PI lift plate home sensor /Up
(PS34) does not turn ON within a turn OFF the main (PS34)
specified period of time. Or, after relay (RL1). PI tray upper limit sensor /
the paper lift motor /Up (M8) is in Up (PS32)
the up operation, the PI tray upper
limit sensor /Up (PS32) does not
turn ON.
SC77-40 After the FD paper lift motor /Lw Paper lift motor /Lw (M9)
(M9) is in the down operation, the PI drive board (PIDB)
PI lift plate home sensor /Lw PI lift plate home sensor /Lw
(PS40) does not turn ON within a (PS40)
specified period of time. Or, after PI tray upper limit sensor /
the paper lift motor /Lw (M9) is in Lw (PS38)
the up operation, the PI tray upper
limit sensor /Lw (PS38) does not
turn ON.
SC77-41 The entrance conveyance motor Entrance conveyance motor
(M1) detects an error detection (M1)
signal for a specified period of Punch drive board (PDB)
time in succession.
SC77-42 The intermediate conveyance Intermediate conveyance
motor (M3) detects an error detec- motor (M3)
tion signal for a specified period of Punch drive board (PDB)
time in succession.
SC77-43 The PI conveyance motor (M7) PI conveyance motor (M7)
detects an error detection signal PI drive board (PIDB)
for a specified period of time in
succession.
SC77-44 The main tray paper exit motor Main tray paper exit motor
(M17) detects an error detection (M17)
signal for a specified period of Punch drive board (PDB)
time in succession.
SC77-48 Resending of communication data Main body I/F wiring har-
due to an error is not available. ness
SC77-49 When non-volatile memory is FD control board (FDCB)
being accessed, no response is EEPROM
obtained for a specified period of
time.
SC77-58* When the FD is unready, a signal Software bug
to start operations is received from
the main body.
SC77-59* Communication error in FD
624 1
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- does not turn ON within a speci- and the SD stop Scrap press home sensor
mality fied period of time after the bundle immediately to (PS48)
drive motor (M5) starts the home turn OFF the main SD control board (SDCB)
position search operation. relay (RL1). SD drive board (SDDB)
SC77-61 Folding main scan alignment Folding main scan alignment
home sensor /Fr1 (PS18) does not motor /Fr (M7)
turn ON within a specified period Folding main scan alignment
of time after the folding main scan home sensor /Fr1 (PS18)
alignment motor /Fr (M7) starts SD control board (SDCB)
the home position search opera- SD drive board (SDDB)
tion.
Or, even after a specified period of
time after M7 starts the operation,
it does not stop.
SC77-62 Folding exit home sensor (PS24) Folding sub scan alignment
does not turn ON within a speci- exit motor (M8)
fied period of time after the folding Folding exit home sensor
sub scan alignment paper exit (PS24)
motor (M8) starts the home posi- SD control board (SDCB)
tion search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M8 starts to decelerate,
it does not stop.
SC77-63 Saddle stitch alignment home Saddle stitching alignment
sensor /Rt (PS28) does not turn motor /Rt (M9)
ON within a specified period of Saddle stitching alignment
time after the saddle stitch align- home sensor /Rt (PS28)
ment motor /Rt (M9) starts the SD control board (SDCB)
home position search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M9 starts the operation,
it does not stop.
SC77-64 Bundle arm home sensor (PS32) Bundle arm motor (M10)
does not turned ON within a spec- Bundle arm home sensor
ified period of time after the bun- (PS32)
dle arm motor (M10) starts the SD control board (SDCB)
home position search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M10 starts the opera-
tion, it does not stop.
1 625
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- (PS33) does not turned ON within and the SD stop Bundle clip upper limit sen-
mality a specified period of time after the immediately to sor (PS33)
bundle clip motor (M11) starts the turn OFF the main Bundle clip lower limit sen-
home position search operation. relay (RL1). sor (PS30)
Or, even after a specified period of SD control board (SDCB)
time after M11 starts the opera- SD drive board (SDDB)
tion, it does not stop.
SC77-66 Bundle registration home sensor Bundle registration motor
(PS34) does not turned ON within (M12)
a specified period of time after the Bundle registration home
bundle registration motor (M12) sensor (PS34)
starts the home position search SD control board (SDCB)
operation. SD drive board (SDDB)
Or, even after a specified period of
time after M12 starts the opera-
tion, it does not stop.
SC77-67 Overlap home sensor (PS17) does Overlap motor (M13)
not turned ON within a specified Overlap home sensor
period of time after the overlap (PS17)
motor (M13) starts the home posi- SD control board (SDCB)
tion search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M13 starts the opera-
tion, it does not stop.
SC77-68 Folding main scan alignment Folding main scan alignment
home sensor /Rr (PS19) does not motor /Rr (M14)
turned ON within a specified Folding main scan alignment
period of time after the folding home sensor /Rr (PS19)
main scan alignment motor /Rr SD control board (SDCB)
(M14) starts the home position SD drive board (SDDB)
search operation.
Or, even after a specified period of
time after M14 starts the opera-
tion, it does not stop.
SC77-69 Stapler moving home sensor Stapler movement motor
(PS25) does not turned ON within (M15)
a specified period of time after the Stapler movement home
stapler moving motor (M15) starts sensor (PS25)
the home position search opera- SD control board (SDCB)
tion. SD drive board (SDDB)
Or, even after a specified period of
time after M15 starts the opera-
tion, it does not stop.
626 1
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- sensor /Lt (PS29) does not turned and the SD stop motor /Lt (M16)
mality ON within a specified period of immediately to Saddle stitching alignment
time after the saddle stitching turn OFF the main home sensor /Lt (PS29)
alignment motor /Lt (M16) starts relay (RL1). SD control board (SDCB)
the home position search opera- SD drive board (SDDB)
tion.
Or, even after a specified period of
time after M16 starts the opera-
tion, it does not stop.
SC77-71 Bundle press movement home Bundle press movement
sensor (PS36) does not turned ON motor (M17)
within a specified period of time Bundle press movement
after the bundle press movement home sensor (PS36)
motor (M17) starts the home posi- SD control board (SDCB)
tion search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M17 starts the opera-
tion, it does not stop.
SC77-72 1st folding blade home sensor /2 1st folding blade motor
(PS21) does not turned ON within (M18)
a specified period of time after the 1st folding blade home sen-
1st folding blade motor (M18) sor /1 (PS20), /2 (PS21)
starts the home position search SD control board (SDCB)
operation. SD drive board (SDDB)
Or 1st folding blade home sensor
/1 (PS20) does not turned ON
within a specified period of time
after M18 starts the operation.
SC77-73 2nd folding blade home sensor /2 2nd folding blade motor
(PS23) does not turned ON within (M19)
a specified period of time after the 2nd folding blade home
2nd folding blade motor (M19) sensor /1 (PS22), /2 (PS23)
starts the home position search SD control board (SDCB)
operation. SD drive board (SDDB)
Or the 2nd folding blade home
sensor /1 (PS22) does not turned
ON within a specified period of
time after M19 starts the opera-
tion.
1 627
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- (PS26) does not turned ON within and the SD stop (M20)
mality a specified period of time after the immediately to Clincher up/down home
clincher up down motor (M20) turn OFF the main sensor (PS26)
starts the home position search relay (RL1). SD control board (SDCB)
operation. SD drive board (SDDB)
Or, even after a specified period of
time after M20 starts the opera-
tion, it does not stop.
SC77-75 Saddle stitching press home sen- Saddle stitching press
sor (PS27) does not turned ON motor (M21)
within a specified period of time Saddle stitching press home
after the saddle stitching press sensor (PS27)
motor (M21) starts the home posi- SD control board (SDCB)
tion search operation. SD drive board (SDDB)
Or, even after a specified period of
time after M21 starts the opera-
tion, it does not stop.
SC77-76 Bundle arm rotation home sensor Bundle arm rotation motor
(PS31) does not turned ON within (M22)
a specified period of time after the Bundle arm rotation home
bundle arm rotation motor (M22) sensor (PS31)
starts the home position search SD control board (SDCB)
operation. SD drive board (SDDB)
Or, even after a specified period of
time after M22 starts the opera-
tion, it does not stop.
SC77-77 Bundle press home sensor (PS37) Bundle press motor (M23)
does not turned ON within a spec- Bundle press home sensor
ified period of time after the bun- (PS37)
dle press motor (M23) starts the Bundle press lower limit
home position search operation. sensor (PS47)
Or, even after a specified period of SD control board (SDCB)
time after M23 starts the opera- SD drive board (SDDB)
tion, it does not stop.
SC77-78 Bundle press stage up down . Bundle press stage up
home sensor (PS35) does not down motor (M24)
turned ON within a specified Bundle press stage up
period of time after the bundle down home sensor (PS35)
press stage up down motor (M24) Bundle press stage up
starts the home position search down limit sensor (PS45)
operation. SD control board (SDCB)
Or PS35 or the bundle press SD drive board (SDDB)
stage up down upper limit sensor
(PS45) does not turned ON after a
specified period of time M24
starts the operation.
628 1
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- does not turned ON within a spec- and the SD stop Guide shaft home sensor
mality ified period of time after the guide immediately to (PS46)
shaft motor (M25) starts the home turn OFF the main SD control board (SDCB)
position search operation. relay (RL1). SD drive board (SDDB)
Or, even after a specified period of
time after M25 starts the opera-
tion, it does not stop.
SC77-80 Stapler home sensor /Rt (HS1) or Stapler assembly /Rt
clincher start sensor /Rt (HS2) SD control board (SDCB)
does not turned ON within a spec- SD drive board (SDDB)
ified period of time after the stapler
motor /Rt (M29) starts the opera-
tion.
SC77-81 Stapler home sensor /Lt (HS3) or Stapler assembly /Lt
clincher start sensor /Lt (HS4) SD control board (SDCB)
does not turned ON within a spec- SD drive board (SDDB)
ified period of time after the stapler
motor /Lt (M30) starts the opera-
tion.
SC77-82 Trimmer blade motor (M31) does Trimmer blade motor (M31)
not turned OFF within a specified Trimmer blade home sensor
period of time after it turned ON. (PS50)
Trimmer blade upper limit
sensor (PS51)
SD control board (SDCB)
SD drive board (SDDB)
SC77-83 Trimmer press motor (M32) does Trimmer press motor (M32)
not turned OFF within a specified Trimmer press home motor
period of time after it turned ON. (PS53)
Trimmer press upper limit
sensor (PS52)
SD control board (SDCB)
SD drive board (SDDB)
SC77-84 Bundle arm assist motor (M26) Bundle arm assist motor
does not turned OFF within a (M26)
specified period of time after it Bundle arm assist home
turned ON. sensor (PS38)
Bundle arm assist upper
limit sensor (PS39)
SD control board (SDCB)
SD drive board (SDDB)
SC77-85 An error detection signal is Entrance conveyance motor
detected for a specified period of (M1)
time in succession while the SD control board (SDCB)
entrance conveyance motor (M1) SD drive board (SDDB)
is ON.
1 629
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- detected for a specified period of and the SD stop motor (M2)
mality time in succession while the hori- immediately to SD control board (SDCB)
zontal conveyance motor (M2) is turn OFF the main SD drive board (SDDB)
ON. relay (RL1).
SC77-87 An error detection signal is Folding entrance motor (M3)
detected for a specified period of SD control board (SDCB)
time in succession while the fold- SD drive board (SDDB)
ing entrance motor (M3) is ON.
SC77-88 An error detection signal is Folding conveyance motor
detected for a specified period of (M4)
time in succession while the fold- SD control board (SDCB)
ing conveyance motor (M4) is ON. SD drive board (SDDB)
SC77-89 An error detection signal is Bundle exit motor (M5)
detected for a specified period of SD control board (SDCB)
time in succession while the bun- SD drive board (SDDB)
dle exit motor (M5) is ON.
SC77-90 An error detection signal is detected Folding sub scan alignment
for a specified period of time in suc- exit motor (M8)
cession while the folding sub scan SD control board (SDCB)
alignment exit motor (M8) is ON. SD drive board (SDDB)
SC77-91 An error detection signal is Scraps removal fan motor
detected for a specified period of (FM1)
time in succession while the SD control board (SDCB)
scraps removal fan motor (FM1) is SD drive board (SDDB)
ON.
And normal operation is not
detected after the restart (retry).
(even after being started for the
specified times)
Or, an error detection is detected
at the start operation and normal
operation is not detected even
after the restart (retry). (normal
operation is not detected after the
start of the specified times after
error detection)
SC77-95 5VDC power supply error detec- SD drive board (SDDB)
tion signal is detected for a speci- SD control board (SDCB)
fied period of time in succession.
SC77-96 Resending of communication data SD control board (SDCB)
to the main body is not available
due to an error.
630 1
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- accessed, no response is obtained and the SD stop EEPROM
mality for a specified period of time. immediately to
SC77-98* When the SD is unready, a signal turn OFF the main Software bug
to start operations is received from relay (RL1).
the main body.
SC77-99* Communication error in SD
PB SC78-01 After the main CPU in the PB con- The main body PB control board (PBCB)
PB
abnor- trol board (PBCB) sends an and the PB stop PB drive board (PBDB)
mality entrance conveyance start signal immediately to Entrance conveyance motor
to the sub CPU, a signal to notify turn OFF the main (M1)
the completion of the procvess is relay (RL1).
not returned to the main CPU
within a specified time period.
SC78-02 An error detection signal is PB control board (PBCB)
detected continuously for a speci- PB drive board (PBDB)
fied time period while the interme- Intermediate conveyance
diate conveyance motor (M2) is motor (M2)
driving.
SC78-04 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends a SC PB drive board (PBDB)
entrance conveyance start signal SC entrance conveyance
to the sub CPU, a signal to notify motor (M11)
the completion of the process is
not returned to the main CPU
within a specified time period.
SC78-05 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends a SC PB drive board (PBDB)
switchback conveyance start sig- SC switchback conveyance
nal to the sub CPU, a signal to motor (M12)
notify the completion of the pro-
cess is not returned to the main
CPU within a specified time
period.
SC78-06 The switchback roller release PB control board (PBCB)
operation has not completed PB drive board (PBDB)
within a specified time period after SC switchback release
the SC switchback release motor motor (M13)
(M13) turns ON.
SC78-07 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends an PB drive board (PBDB)
SC alignment start signal to the SC alignment motor (M15)
sub CPU, a signal to notify the
completion of the process is not
returned to the main CPU within a
specified time period.
2 631
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- control board (PBCB) sends an and the PB stop PB drive board (PBDB)
mality SC pages conveyance start signal immediately to SC bundle conveynace
to the sub CPU, a signal to notify turn OFF the main motor (M17)
the completion of the process is relay (RL1).
not returned to the main CPU
within a specified time period.
SC78-09 The SC roller release operation PB control board (PBCB)
has not completed within a speci- PB drive board (PBDB)
fied time period after the SC roller SC roller release motor
release motor (M18) turns ON. (M18)
SC78-10 The movement of the SC entrance PB control board (PBCB)
has not completed within a speci- PB drive board (PBDB)
fied time period after the clamp Clamp entranse movement
entrance movement motor (M19) motor (M19)
turns ON.
SC78-11 The SC entrance roller release PB control board (PBCB)
operation has not completed PB drive board (PBDB)
within a specified time period after Clamp entranse roller
the clamp entrance roller release release motor (M20)
motor (M20) turns ON
SC78-12 After clamp alignment motor PB control board (PBCB)
(M21) turns on, the alignment PB drive board (PBDB)
operation is not complete within Clamp alignment motor
the specified time. (M21)
SC78-13 After clamp motor (M22) turns on, PB control board (PBCB)
the open/close process of the PB drive board (PBDB)
clamp section is not complete Clamp motor (M22)
within the specified time.
SC78-14 The rotation of the clamp section PB control board (PBCB)
has not completed within a speci- PB drive board (PBDB)
fied time period after the clamp Clamp rotation motor (M23)
rotation motor (M23) turns ON.
SC78-15 The movement of the glue tank PB control board (PBCB)
has not completed within a speci- PB drive board (PBDB)
fied time period after the glue tank Glue tank movement motor
movement motor (M31) turns ON. (M31)
SC78-16 An error detection signal is PB control board (PBCB)
detected continuously for a speci- PB drive board (PBDB)
fied time period while the glue Glue apply roller motor
apply roller motor (M32) is driving. (M32)
632 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- of pellets, which is counted by the and the PB stop PB drive board (PBDB)
mality pellet count sensor (PS37), has immediately to Pellet supply motor (M33)
not been reached after the pellet turn OFF the main
supply motor (M33) turns ON. The relay (RL1).
status was detected by a speci-
fied number of times in succes-
sion.
SC78-18 The movement of the pellet supply PB control board (PBCB)
arm has not completed within a PB drive board (PBDB)
specified time period after the pel- pellet supply arm motor
let supply arm motor (M34) turns (M34)
ON.
SC78-19 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends a SC PB drive board (PBDB)
alignment start signal to the sub Cover paper alignment
CPU, a signal to notify the com- motor (M41)
pletion of the process is not
returned to the main CPU within a
specified time period.
SC78-20 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends a PB drive board (PBDB)
book ejection start signal to the Book exit motor (M42)
sub CPU, a signal to notify the
completion of the process is not
returned to the main CPU within a
specified time period.
SC78-21 After the main CPU on the PB PB control board (PBCB)
control board (PBCB) sends a PB drive board (PBDB)
driven arm/Rt shaking operation Cover paper conveyance
start signal to the sub CPU, a sig- arm motor /Rt (M43)
nal to notify the completion of the
process is not returned to the
main CPU within a specified time
period.
SC78-22 After the main CPU in the PB con- PB control board (PBCB)
trol board (PBCB) sends a driven PB drive board (PBDB)
arm/Lt shaking operation start sig- Cover paper conveyance
nal to the sub CPU, a signal to arm motor /Lt (M44)
notify the completion of the pro-
cess is not returned to the main
CPU within a specified time
period.
2 633
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- control board (PBCB) sends a and the PB stop PB drive board (PBDB)
mality cover paper conveyance start sig- immediately to Cover paper conveyance
nal to the sub CPU, a signal to turn OFF the main motor (M45)
notify the completion of the pro- relay (RL1).
cess is not returned to the main
CPU within a specified time
period.
SC78-24 The cover paper table up or down PB control board (PBCB)
movement has not completed PB drive board (PBDB)
within a specified time period after Cover paper table up down
the cover paper table up down motor /Fr (M46)
motor/Fr (M46) turns ON.
SC78-25 The cover paper table up or down PB control board (PBCB)
movement has not completed PB drive board (PBDB)
within a specified time period after Cover paper table up down
the cover paper table up down motor /Rr (M47)
motor/Rr (M47) turns ON.
SC78-26 The movement of the cover paper PB control board (PBCB)
folding plate/Rt has not completed PB drive board (PBDB)
within a specified time period after Cover paper folding motor /
the cover paper folding motor/Rt Rt (M48)
(M48) turns ON.
SC78-27 The movement of the cover paper PB control board (PBCB)
folding plate/Lt has not completed PB drive board (PBDB)
within a specified time period after Cover paper folding motor /
the cover paper folding motor/Lt Lt (M49)
(M49) turns ON.
SC78-28 The trimming of the cover paper PB control board (PBCB)
has not completed within a speci- PB drive board (PBDB)
fied time period after the cutter Cutter motor (M50)
motor (M50) turns ON.
SC78-30 After the main CPU in the PB con- PB control board (PBCB)
trol board (PBCB) sends a car- PB drive board (PBDB)
riage belt driving operation start Book conveyance belt
signal to the sub CPU, a signal to motor (M61)
notify the completion of the pro-
cess is not returned to the main
CPU within a specified time
period.
SC78-31 The carriage section movement PB control board (PBCB)
according to paper size has not PB drive board (PBDB)
completed after the book convey- Book conveyance belt
ance belt movement motor (M62) movement motor (M62)
turns ON.
634 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- riage section has not completed and the PB stop PB drive board (PBDB)
mality within a specified time period after immediately to Book conveyance belt up
the cover paper conveyance belt turn OFF the main down motor (M63)
up/down motor (M63) turns ON. relay (RL1).
SC78-34 The pressing of the back edge of PB control board (PBCB)
the book process has not com- PB drive board (PBDB)
pleted within a specified time Book stopper motor (M65)
period after the book stopper
motor (M65) turns ON.
SC78-35 An error detection signal is PB control board (PBCB)
detected continuously for speci- PB drive board (PBDB)
fied time period while the cover Cover paper tray fan /1
paper tray fan/1 (M71) is started or (M71)
driving.
SC78-36 An error detection signal is PB control board (PBCB)
detected continuously for speci- PB drive board (PBDB)
fied time period while the cover Cover paper tray fan /2
paper tray fan/2 (M72) is started or (M72)
driving.
SC78-37 The tray up movement has not PB control board (PBCB)
completed within a specified time PB drive board (PBDB)
period after the cover paper tray Cover paper tray lift motor
lift motor (M73) turns ON. (M73)
SC78-38 An error detection signal is PB control board (PBCB)
detected continuously for a speci- PB drive board (PBDB)
fied time period while the cover Cover paper feed motor
paper feed motor (M74) is driving. (M74)
SC78-39 An error detection signal is PB control board (PBCB)
detected continuously for speci- PB drive board (PBDB)
fied time period while the ventila- Exhaust fan /1 (M80)
tion fan/1 (M80), /2 (M81) is Exhaust fan /2 (M81)
started of driving.
SC78-40 After the warm-up is started, tem- AC drive board (ACDB)
** perature detected by the glue tank Glue tank heater (H1)
temperature sensor /Md (TH3) has Glue apply roller heater (H2)
not risen to a prescribed level PB control board (PBCB)
within a specified time period. PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Md (TH3)
2 635
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- ** perature detected by the glue tank and the PB stop Glue tank heater (H1)
mality temperature sensor /Lw (TH4) has immediately to Glue apply roller heater (H2)
not risen to a prescribed level turn OFF the main PB control board (PBCB)
within a specified time period. relay (RL1). PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Lw (TH4)
SC78-42 After the warm-up is started, tem- AC drive board (ACDB)
** perature detected by the glue Glue tank heater (H1)
apply roller temperature sensor Glue apply roller heater (H2)
(TH1) has not risen to a prescribed PB control board (PBCB)
level within a specified time PB drive board (PBDB)
period. Glue apply roller motor
(M32)
Glue apply roller tempera-
ture sensor (TH1)
SC78-43 After the pellet supply, tempera- AC drive board (ACDB)
** ture detected by the glue tank Glue tank heater (H1)
temperature sensor/Up (TH2) has Glue apply roller heater (H2)
not risen to a prescribed level PB control board (PBCB)
within a specified time period. PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Up (TH2)
SC78-44 During standby, after the glue tank AC drive board (ACDB)
** heater (H1) is turned ON, temper- Glue tank heater (H1)
ature detected by the glue tank Glue apply roller heater (H2)
temperature sensor /Md (TH3) has PB control board (PBCB)
not risen to a prescribed level PB drive board (PBDB)
within a specified time period. Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Md (TH3)
SC78-45 When control temperature is AC drive board (ACDB)
** reached, after the glue tank heater Glue tank heater (H1)
(H1) is turned ON, temperature Glue apply roller heater (H2)
detected by the glue tank temper- PB control board (PBCB)
ature sensor/Lw (TH4) has not PB drive board (PBDB)
risen to a prescribed level within a Glue apply roller motor
specified time period. (M32)
Glue tank temperature sen-
sor /Lw (TH4)
636 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- ** reached, after the glue tank heater and the PB stop Glue tank heater (H1)
mality (H1) is turned ON, temperature immediately to Glue apply roller heater (H2)
detected by the glue apply roller turn OFF the main PB control board (PBCB)
temperature sensor (TH1) has not relay (RL1). PB drive board (PBDB)
risen to a prescribed level within a Glue apply roller motor
specified time period. (M32)
Glue apply roller tempera-
ture sensor (TH1)
SC78-47 An abnormal high temperature is AC drive board (ACDB)
** detected by the glue apply roller Glue tank heater (H1)
temperature sensor (TH1). Glue apply roller heater (H2)
PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue apply roller tempera-
ture sensor (TH1)
SC78-48 An abnormal high temperature is AC drive board (ACDB)
** detected by the glue tank temper- Glue tank heater (H1)
ature sensor /Up (TH2). Glue apply roller heater (H2)
PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Up (TH2)
SC78-49 An abnormal high temperature is AC drive board (ACDB)
** detected by the glue tank temper- Glue tank heater (H1)
ature sensor /Md (TH3). Glue apply roller heater (H2)
PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Md (TH3)
SC78-50 An abnormal high temperature is AC drive board (ACDB)
** detected by the glue tank temper- Glue tank heater (H1)
ature sensor /Lw (TH4). Glue apply roller heater (H2)
PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Lw (TH4)
2 637
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- ** sensor (TH1) high temperature and the PB stop Glue tank heater (H1)
mality hardware detection. immediately to Glue apply roller heater (H2)
An abnormal high temperature is turn OFF the main PB control board (PBCB)
detected by the glue apply roller relay (RL1). PB drive board (PBDB)
temperature sensor (TH1). Glue apply roller motor
(M32)
Glue apply roller tempera-
ture sensor (TH1)
SC78-52 The glue tank temperature sensor AC drive board (ACDB)
** /Up (TH2) high temperature hard- Glue tank heater (H1)
ware detection. Glue apply roller heater (H2)
An abnormal high temperature is PB control board (PBCB)
detected by the glue tank temper- PB drive board (PBDB)
ature sensor /Up (TH2). Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Up (TH2)
SC78-53 The glue tank temperature sensor AC drive board (ACDB)
** /Md (TH3) high temperature hard- Glue tank heater (H1)
ware detection. Glue apply roller heater (H2)
An abnormal high temperature is PB control board (PBCB)
detected by the glue tank temper- PB drive board (PBDB)
ature sensor /Md (TH3). Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Md (TH3)
SC78-54 The glue tank temperature sensor AC drive board (ACDB)
** /Lw (TH4) high temperature hard- Glue tank heater (H1)
ware detection. Glue apply roller heater (H2)
An abnormal high temperature is PB control board (PBCB)
detected by the glue tank temper- PB drive board (PBDB)
ature sensor /Lw (TH4). Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Lw (TH4)
SC78-55 An abnormal low temperature is AC drive board (ACDB)
** detected by the glue apply roller Glue tank heater (H1)
temperature sensor (TH1), after Glue apply roller heater (H2)
completion of warm-up. PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue apply roller tempera-
ture sensor (TH1)
638 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- ** detected by the glue tank temper- and the PB stop Glue tank heater (H1)
mality ature sensor /Up (TH2), after immediately to Glue apply roller heater (H2)
reaching glue supply control tem- turn OFF the main PB control board (PBCB)
perature. relay (RL1). PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Up (TH2)
SC78-57 An abnormal low temperature is AC drive board (ACDB)
** detected by the glue tank Glue tank heater (H1)
temperature sensor /Md (TH3), Glue apply roller heater (H2)
after the warming-up is com- PB control board (PBCB)
pleted. PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Md (TH3)
SC78-58 An abnormal low temperature is AC drive board (ACDB)
** detected by the glue tank temper- Glue tank heater (H1)
ature sensor /Lw (TH4), after the Glue apply roller heater (H2)
warming-up is completed. PB control board (PBCB)
PB drive board (PBDB)
Glue apply roller motor
(M32)
Glue tank temperature sen-
sor /Lw (TH4)
SC78-59 Glue apply roller temperature sen- AC drive board (ACDB)
** sor (TH1) low temperature abnor- Glue tank heater (H1)
mality hardware detection. Glue apply roller heater (H2)
TH1 detected low temperature PB control board (PBCB)
abnormality of the glue apply roller PB drive board (PBDB)
abnormality detection signal after Glue apply roller motor
the warming-up is completed. (M32)
Glue apply roller tempera-
ture sensor (TH1)
SC78-60 Glue tank temperature sensor/Up AC drive board (ACDB)
** (TH2) low temperature abnormality Glue tank heater (H1)
hardware detection . Glue apply roller heater (H2)
TH2 detected low temperature PB control board (PBCB)
abnormality of the glue tank PB drive board (PBDB)
abnormality detection signal after Glue apply roller motor
reaching the glue supply control (M32)
temperature. Glue tank temperature sen-
sor /Up (TH2)
2 639
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
abnor- ** (TH3) low temperature abnormality and the PB stop Glue tank heater (H1)
mality hardware detection. immediately to Glue apply roller heater (H2)
TH3 detected low temperature turn OFF the main PB control board (PBCB)
abnormality of the glue tank relay (RL1). PB drive board (PBDB)
abnormality detection signal after Glue apply roller motor
the warming-up is completed. (M32)
Glue tank temperature sen-
sor /Md (TH3)
SC78-62 Glue tank temperature sensor /Lw AC drive board (ACDB)
** (TH4) low temperature abnormality Glue tank heater (H1)
hardware detection. Glue apply roller heater (H2)
TH4 detected low temperature PB control board (PBCB)
abnormality of the glue tank PB drive board (PBDB)
abnormality detection signal after Glue apply roller motor
the warming-up is completed. (M32)
Glue tank temperature sen-
sor /Lw (TH4)
SC78-63 Abnormal rotation of the exhaust AC drive board (ACDB)
fan/2 (M81) on start-up does not PB control board (PBCB)
recover by reboot. PB drive board (PBDB)
Abnormal rotation of the exhaust Exhaust fan /2 (M81)
fan/2 (M81) during M81 is on does
not recover by reboot.
SC78-64 Abnormal rotation of the pellet AC drive board (ACDB)
cooler fan (M4) on start-up does PB control board (PBCB)
not recover by reboot. PB drive board (PBDB)
Abnormal rotation of the pellet Pellet supply cooling fan
cooler fan (M4) during M4 is on motor (M4)
does not recover by reboot.
SC78-91 Message queue full or the control PB control board (PBCB)
abnormality of Sub CPU1 in the Control program
PB control board (PBCB).
SC78-92 Message queue full or the control PB control board (PBCB)
abnormality of Sub CPU2 in the Control program
PB control board (PBCB).
SC78-93 Communication abnormality PB control board (PBCB)
between Main CPU in the PB con- Control program
trol board (PBCB) and Sub CPU1.
SC78-94 Communication abnormality PB control board (PBCB)
between Main CPU in the PB con- Control program
trol board (PBCB) and Sub CPU2.
SC78-96 Paper feed abnormality between PB control board (PBCB)
the main body and the PB. Control program
SC78-97 Non-volatile memory error in the PB control board (PBCB)
PB control board (PBCB). Control program
640 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnor- mality. and the PB stop
mality PB received operation start signal immediately to
from the main body when the PB turn OFF the main
is unready. relay (RL1).
SC78-99 Message queue of the communi- Control program
cation among tasks in the PB is
full.
Commu- SC80-01 In the communication check The main body Overall control board
Main body
2 641
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
nication or an error is detected during the stops immediately SD control board (SDCB)
abnor- ROM check. to turn OFF the Wiring harness between the
mality main relay (RL1). SDCB and the main body
SC80-42 The firmware is not written on FS FS firmware
FS
642 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
nication between ADU drive board /1 stops immediately ADU drive board /1
abnor- (ADJDB1) and printer control to turn OFF the (ADJDB1)
mality board (PRCB), no response is Rl1 (main). Loose connection
returned from ADUDB1 after a
specified time from turning ON of
the main power switch (SW1) and
sub power switch (SW2) (ID=11).
SC90-06 In the communication check Printer control board (PRCB)
between ADU drive board /1 ADU drive board /1
(ADUDB1) and printer control (ADJDB1)
board (PRCB), an error was Loose connection
detected (ID=11).
Power SC93-01 Error detection signal (blown fuse) ADU drive board /1
abnor- of ADU drive board /1 (ADUDB1) (ADJDB1)
mality was detected.
SC93-05 Error detection signal (blown fuse) DC power supply /1
of offset sensor (PS54) or transfer (DCPS1)
exposure lamp (TSL) was
detected and an error signal (24V
disconnection) was detected.
SC93-06 Error detection signal (blown fuse) Centering sensor (PS54)
of offset sensor (PS54) or transfer Transfer exposure lamp
exposure lamp (TSL) was (TSL)
detected but no error signal (24V ADU lock solenoid (SD6)
disconnection) is detected. Reverse/exit solenoid (SD7)
Thick paper assist solenoid
(SD8)
SC93-08 Error detection signal (24V blown PF drive board (PFUDB)
fuse) of PF drive board (PFUDB)
was detected.
Fan SC95-01 The EM signal is found abnormal a ADU drive board /1
abnor- specified period of time after the (ADJDB1)
mality ADU cooling fans /1 (FM14), /2 ADU cooling fan /1 (FM14), /
(FM15) and /3 (FM13), the sensor 2 (FM15), /3 (FM13)
cooling fan (FM16) and the regis- Sensor cooling fan (FM16)
tration cooling fan (FM17) turn on. Registration cooling fan
And the signal is still found abnor- (FM17)
mal a specified period of time after
it turns on again after turning off,
and the door close of the door
open/close sensors /1 (PS1) and /
2 (PS2) and the PF door open/
close sensor (PS70) has been
detected 10 times in a row.
1 643
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
While detached, an error detection is not carried out on these detached units.
There are 2 methods of setting for limited use.
644
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
SC67-06 Original reverse abnormality (DF connection not recognized)
SC67-07 Original reverse/exit abnormality
SC67-08 Tray up/down abnormality
SC76-01 Tandem (1st) LS stacker tray up down The use of the tandem (1st) LS is DIPSW33-06
LS
abnormality unavailable.
SC76-02 Tandem (1st) LS shift unit drive abnormality
SC76-03 Tandem (1st) LS alignment plate drive
abnormality
SC76-04 Tandem (1st) LS grip drive abnormality
SC76-05 Tandem (1st) LS stacker tray upper
limit abnormality
SC76-06 Tandem (1st) LS stacker tray lower limit
abnormality
SC76-07 Tandem (1st) LS paper cooling fan /Fr
drive abnormality
SC76-08 Tandem (1st) LS cooling fan drive
abnormality
SC76-09 Tandem (1st) LS paper cooling fan /Mi
drive abnormality
SC76-10 Tandem (1st) LS motor cooling fan
drive abnormality
SC76-11 Tandem (1st) LS paper cooling fan /Rr
drive abnormality
SC76-31 Tandem (2nd) LS stacker tray up down The use of the tandem (2nd) LS DIPSW33-07
abnormality is unavailable
SC76-32 Tandem (2nd) LS shift unit drive abnormality
SC76-33 Tandem (2nd) LS alignment plate drive
abnormality
SC76-34 Tandem (2nd) LS grip drive abnormality
SC76-35 Tandem (2nd) LS stacker tray upper
limit abnormality
SC76-36 Tandem (2nd) LS stacker tray lower
limit abnormality
SC76-37 Tandem (2nd) LS paper cooling fan /Fr
drive abnormality
SC76-38 Tandem (2nd) LS cooling fan drive
abnormality
SC76-39 Tandem (2nd) LS paper cooling fan /Mi
drive abnormality
SC76-40 Tandem (2nd) LS motor cooling fan
drive abnormality
SC76-41 Tandem (2nd) LS paper cooling fan /Rr
drive abnormality
645
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
SC77-31 2nd folding cam drive abnormality and the punch section is unavail-
able
SC77-32 3rd folding cam drive abnormality
SC77-33 2 holes punch drive abnormality
SC77-34 3 holes/4 holes punch drive abnormality
SC77-35 Punch alignment plate drive abnormality
SC77-36 Punch paper rear registration drive
abnormality
SC77-37 Main tray upper limit abnormality Main tray paper exit is unavail- DIPSW33-2
able
SC77-38 Main tray lower limit abnormality
SC77-39 PI lift plate /Up up/down abnormality The use of the PI section DIPSW33-3
SC77-40 PI lift plate /Lw up/down abnormality unavailable
SC77-41 Entrance conveyance drive abnormality The use of the entire FD unavail- DIPSW33-4
SC77-42 Intermediate conveyance drive abnormality able
SC77-43 PI conveyance drive abnormality
SC77-44 Paper exit conveyance drive abnormality
SC77-60 Bundle exit drive abnormality The use of the saddle stitching, multi DIPSW34-0,
SD
646 1
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
abnormality multi center folding and trimmer 1, 3
SC77-64 Bundle arm drive abnormality unavailable
SC77-65 Bundle clip drive abnormality
SC77-66 Bundle registration drive abnormality
SC77-67 Overlap drive abnormality The use of the saddle stitching, DIPSW34-0,
SC77-68 Folding main scan alignment /Rr drive multi center folding, multi letter 1, 2, 3
abnormality folding and trimmer unavailable
SC77-69 Stapler movement drive abnormality The use of the saddle stitching, DIPSW34-0,
SC77-70 Saddle stitching alignment /Lt drive multi center folding and trimmer 1, 3
abnormality unavailable
SC77-71 Bundle press movement drive abnor-
mality
SC77-72 1st folding blade drive abnormality The use of the saddle stitching, DIPSW34-0,
multi center folding, multi letter 1, 2, 3
folding and trimmer unavailable
SC77-73 2nd folding blade abnormality The use of the multi center fold- DIPSW34-2
ing unavailable
SC77-74 Clincher up down drive abnormality The use of the saddle stitching, DIPSW34-0,
SC77-75 Saddle stitching press drive abnormality multi center folding and trimmer 1, 3
SC77-76 Bundle arm rotation drive abnormality unavailable
1 647
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
ity
SC78-02 Intermediate conveyance drive abnor- Ejecting onto the sub tray is pos- DIPSW35-4
mality sible.
SC78-04 SC entrance conveyance drive abnor-
mality
SC78-05 SC switchback conveyance drive
abnormality
SC78-06 SC switchback roller release drive
abnormality
SC78-07 SC alignment drive abnomality
SC78-08 SC paper detection conveyance drive
abnormality
SC78-09 SC roller release drive abnormality
SC78-10 SC clamp entrance movement drive
abnomality
SC78-11 SC clamp entrance roller release drive
abnormality
SC78-12 Clamp alignment drive abnormality
SC78-13 Clamp open/close drive abnormality
SC78-14 Clamp rotation drive abnormality
SC78-15 Glue tank movement drive abnormality
SC78-16 Glue apply roller rotation drive abnor-
mality
SC78-18 Pellet supply arm drive abnormality
SC78-19 Up/down cover paper alignment drive
abnormality
SC78-20 Up/down cover paper book paper exit
drive abnormality
SC78-21 Driven arm /Rt drive abnormality
SC78-22 Driven arm /Lt drive abnormality
SC78-23 Up/down cover paper conveyance
drive abnormality
SC78-24 Up/down cover paper/Fr up/down
drive abnormality
SC78-25 Up/down cover paper/Rr up/down
drive abnormality
SC78-26 Cover paper folding board /Rt drive
abnormality
SC78-27 Cover paper folding board /Lt drive
abnormality
SC78-28 Cover paper trimming cutter drive
abnormality
SC78-30 Carriage belt drive abnormality
648 2
Field Service Ver3.0 Nov.2006 14. MALFUNCTION CODE
1050e/1050eP
mality sible.
SC78-32 Carriage up/down drive abnormality
SC78-33 Book movement drive abnormality
SC78-34 Book stopper drive abnormality
SC78-35 Cover paper tray fan /1 drive abnomal- Paper feed from the PB is DIPSW35-3
ity unavailable.
SC78-36 Cover paper tray fan /2 drive abnomal-
ity
SC78-37 Cover paper tray up/down drive
abnomality
SC78-38 Cover page conveyance drive abnor-
mality
SC78-39 Exhaust fan drive abnormality Ejecting onto the sub tray is pos- DIPSW35-4
sible.
SC78-40 Warming-up abnormality The use of the PB is unavailable DIPSW35-5
Glue tank middle temperature abnor-
mality
SC78-41 Warming-up abnormality
Glue tank low temperature abnormality
SC78-42 Warming-up abnormality
Glue apply roller temperature abnor-
mality
SC78-43 Glue supply abnormality
Glue tank high temperature abnormal-
lity
SC78-44 Heater continuous energization abnor-
mality
Glue tank middle temperature abnor-
mality
SC78-45 Heater continuous energization abnor-
mality
Glue tank low temperature abnormality
SC78-46 Heater continuous energization abnor-
mality
Glue apply roller temperature abnor-
mality
SC78-47 High temperature abnormality
Glue apply roller temperature abnor-
mality
SC78-48 High temperature abnormality
Glue tank high temperature abnormal-
lity
2 649
14. MALFUNCTION CODE Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
650 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
15. ELECTRICAL PARTS LAYOUT DRAWING
15.1 Main body
A. Switch/sensor
(1) Main body rear side
[1] Pump encoder sensor /1 (PS28) [3] Dehumidification heater switch (SW3)
[2] Pump encoder sensor /2 (PS29)
651
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[6]
[5]
[4]
[3]
[2]
1050fs5002c
[1] Air motor encoder sensor (PS30) [6] Door open/close sensor /1 (PS1)
[2] Main power switch (SW1) [7] Scanner home sensor (PS51)
[3] Interlock switch /2 (MS2) [8] APS sensor /1 (PS52)
[4] Door open/close sensor /2 (PS2) [9] APS sensor /2 (PS53)
[5] Interlock switch /1 (MS1)
652
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[2]
1050e/1050eP
[1] 1050fs5003c
[1] Charger cleaning home sensor (PS26) [2] Charger cleaning limit sensor (PS27)
653
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[2]
[3]
[4]
[5]
1050fs5005c
[1] Toner remaining sensor /1 (PS31) [4] Toner remaining sensor /3 (PS33)
[2] Door switch /2 (SW5) [5] Toner remaining sensor /4 (PS34)
[3] Toner remaining sensor /2 (PS32)
[2] [1]
1050fs5006c
[1] Drum temperature sensor (TH5) [2] Drum potential sensor (DPS)
654
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[8]
1050e/1050eP
[6] [7]
[5]
[1]
[4]
[1] Handle release sensor /1 (PS9), /2 (PS15) [5] Remaining paper VR /1 (VR1), /2 (VR3)
[2] Paper size VR /1 (VR2), /2 (VR4) [6] Upper limit sensor /1 (PS6), /2 (PS12)
[3] Paper size sensor /Rr1 (PS5), /2 (PS11) [7] Paper feed sensor /1 (PS7), /2 (PS13)
[4] Paper size sensor /Fr1 (PS4), /Fr2 (PS10) [8] Paper empty sensor /1 (PS8), /2 (PS14)
655
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[7]
[6]
[5]
[2]
[4]
[3]
1050fs5063c
656
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
1050fs5007c
[1] ADU deceleration sensor (PS42) [3] Paper leading edge sensor (PS41)
[2] Centering sensor (PS54) [4] Registration sensor (PS40)
[1] ADU exit sensor (PS43) [6] Paper exit sensor (PS3)
[2] ADU conveyance sensor /2 (PS36) [7] Reverse sensor /1 (PS48)
[3] ADU conveyance sensor /1 (PS35) [8] Reverse sensor /2 (PS47)
[4] ADU accelerate sensor (PS49) [9] ADU reverse sensor /1 (PS46)
[5] ADU reverse paper exit sensor (PS50) [10] ADU reverse sensor /2 (PS45)
657
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3] [1]
[2]
1050fs5009c
[1] Transfer/separation cleaning limit sensor (PS39) [3] ADU handle release sensor (PS44)
[2] Transfer/separation cleaning home sensor (PS38)
[1]
1050fs5010c
658
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[8]
[7]
[6]
[3]
1050fs5011c
[1]
1050fs5012c
659
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. Load
(1) Main body rear side
/1050e/1050eP
[13] [1]
[2]
[3]
[12]
[11] [4]
[10]
[5]
[9]
[6]
[8] [7]
1050fs5013d
[1] Pump cooling fan (FM11) [12] Vertical conveyance motor (M8)
[2] Cooling fan /1 (FM1) [13] IC cooling fan (FM24)
[3] Paper exit motor /1 (M9) [14] Developing motor (M3)
[4] ADU reverse paper exit motor (M31) [15] Drum motor (M2)
[5] Conveyance motor (M5) [16] Cooling fan /3 (FM3)
[6] Transfer/separation suction fan (FM4) [17] Scanner motor (M27)
[7] Power supply cooling fan /3 (FM27) [18] Cooling fan /2 (FM2)
[8] Power supply cooling fan /2 (FM26) [19] Fusing motor (M1)
[9] Power supply cooling fan /1 (FM25) [20] Air pump motor (M29)
[10] Paper feed motor (M4) [21] Toner pump motor (M28)
[11] Developing suction fan (FM5)
660 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[1]
1050e/1050eP
[3] [2]
[4]
1050fs5014c
[1] Air separation motor (M10) [3] Scanner cooling fan (FM19)
[2] IPB cooling fan (FM12) [4] Suction fan /4 (FM29) (1050e/1050eP only)
[1]
[2]
[3]
[4]
1050fs5015c
2 661
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[3]
[2]
[1]
1050fs5016c
[1] Paper exit cooling fan /2 (FM10) [3] Paper exit cooling fan /1 (FM9)
[2] Paper exit cooling fan /3 (FM28)
[1]
1050fs5017c
662
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
1050fs5018c
[5]
[1]
[4]
[2]
[3]
1050fs5019c
[1] Tray lock solenoid /1 (SD1) [4] Toner hopper motor (M7)
[2] Tray lock solenoid /2 (SD2) [5] Toner bottle motor (M6)
[3] Intermediate hopper motor (M11)
663
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
1050fs5020c
[5] [6]
[4]
[1]
[3]
[2]
1050fs5064c
[1] Paper feed clutch /1 (CL4), /2 (CL6) [4] Pick-up solenoid /1 (SD3), /2 (SD4)
[2] Separation clutch /1 (CL5), /2 (CL7) [5] Paper feed assist fan /Fr1 (FM20), /Fr2 (FM22)
[3] Paper lift motor /1 (M25), /2 (M26) [6] Paper feed assist fan /Rr1 (FM21), /Rr2 (FM23)
664
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[2]
1050fs5066c
[3]
[2]
[1]
1050fs5065c
665
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(11) ADU
/1050e/1050eP
[4]
[6]
[7]
[8]
[10]
[9]
1050fs5021c
666
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
1050fs5022c
[1]
1050fs5023c
667
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[24]
[25]
[2]
[3]
[4]
[5]
668
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[4]
1050fs5025c
[1] 1050fs5031c
669
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2] [1]
/1050e/1050eP
1050fs5026c
[1] Drum potential sensor board (DPSB) [2] Toner control sensor board (TCSB)
[2] [1]
1050fs5027c
[1] Multi feed detection board /2 (MFDB2) [2] Multi feed detection board /1 (MFDB1)
670
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[4] [3]
[2]
1050fs5028c
[1] Transfer exposure lamp (TSL) [3] ADU drive board /2 (ADUDB2)
[2] High voltage unit /2 (HV2) [4] ADU drive board /1 (ADUDB1)
671
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2] [3]
/1050e/1050eP
[1]
1050fs5029c
[1] Polygon motor drive board (PMDB) [3] Laser drive board (LDB)
[2] Index board (INDEXB)
[2] [3]
[1]
1050fs5030c
[1] Fusing heater lamp /2 (L3) [3] Fusing heater lamp /1 (L2)
[2] Fusing heater lamp /3 (L4)
672
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1] [2] [3]
[8]
[4]
[5]
[6] [7]
1050fs5032c
673
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
15.2 DF-603
A. Front side
/1050e/1050eP
[1]
[5]
[1] Multi feed detection board /2 (MFDB2) [4] Gate solenoid (SD303)
[2] Exit gate solenoid (SD304) [5] RADF open/close sensor (PS301)
[3] Pressure roller release solenoid (SD302)
674
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[2]
[3]
[4]
[5]
[1] Original conveyance motor (M301) [9] Original paper exit motor /1 (M304)
[2] Original skew sensor /Rr (PS311) [10] Original paper exit motor /2 (M305)
[3] Original conveyance sensor (PS308) [11] RADF control board (RADFCB)
[4] Original skew sensor /Fr (PS312) [12] Cooling fan /Rt (FM302)
[5] Cooling fan /Lt (FM301) [13] Tray up/down motor (M303)
[6] APS timing sensor (PS317) [14] Cover open/close switch (MS301)
[7] Original feed motor (M302) [15] Tray lower limit sensor (PS316)
[8] SDF switching solenoid (SD301)
675
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
C. Upper surface
/1050e/1050eP
[6]
[11]
[7]
[8]
[10] [14] [13] [12] [4]
[9]
df603fs5003c
[1] Original count sensor (PS310) [10] Multi feed sensor /2 (MFS2)
[2] Original size sensor /Lt (PS303) [11] Original registration sensor /Lt (PS306)
[3] Original size sensor /Rt (PS302) [12] Original reverse sensor (PS309)
[4] Reverse jam sensor (PS304) [13] Centering LED sensor /Fr (PS319)
[5] Original empty sensor (PS305) [14] Centering sensor /Fr (PS320)
[6] Tray upper limit sensor (PS315) [15] Centering sensor /Rr (PS321)
[7] Original registration sensor /Rt (PS318) [16] Centering LED sensor /Rr (PS322)
[8] Multi feed sensor /1 (MFS1) [17] Original exit sensor /Lt (PS307)
[9] Multi feed detection board /1 (MFDB1)
676
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[2]
df603fs5004c
[1]
[2] df603fs5005c
[1] Original exit sensor /Rt (PS314) [2] Original reverse/exit sensor (PS313)
677
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
15.3 PF-701
A. Configuration front side
/1050e/1050eP
[1]
[6]
[2]
[5]
[4]
[3]
pf701fs5001c
[1]
[6]
[2]
[5]
[4]
[3]
pf701fs5002c
678
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[2]
[3]
[7]
[4]
[5]
[6]
pf701fs5003c
679
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
/1050e/1050eP
[2]
[12]
[3]
[4]
[5]
[6]
[11]
[7]
[8]
[10] [9]
pf701fs5004c
680
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[1]
1050e/1050eP
[2]
[3]
[10]
[4]
[5]
[9]
[8]
[1] Paper feed assist fan /Fr1, /Fr2, /Fr3 [6] Remaining paper VR /1, /2, /3 (VR10/VR12/
(FM41/FM43/FM45) VR14)
[2] Pick-up solenoid /1, /2, /3 (SD14/SD15/SD16) [7] Forced separation clutch (CL11) (tray 4 only)
[3] Paper feed sensor /1, /2, /3 (PS72/PS78/PS84) [8] Separation clutch /1, /2, /3 (CL7/CL10/CL13)
[4] Upper limit sensor /1, /2, /3 (PS71/PS77/PS83) [9] Pick-up clutch /1, /2, /3 (CL6/CL9/CL12)
[5] Paper lift motor /1, /2, /3 (M42/M43/M44) [10] Paper feed assist fan /Rr1, /Rr2, /Rr3
(FM42/FM44/FM46)
681
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
F. Tray section 2
[4] [1]
/1050e/1050eP
[1] Paper size VR /1, /2, /3 (VR11/VR13/VR15) [3] Paper size sensor /Fr1, /Fr2, /Fr3 (PS75/
[2] Paper size sensor /Rr1, /Rr2, /Rr3 (PS76/ PS81/PS87)
PS82/PS88) [4] Paper empty sensor /1, /2, /3 (PS73/PS79/
PS85)
G. PP-701 (OPTIONAL)
[1]
[2]
[4] [3]
a08rf5c001ca
[1] Rear paper feed assist fan /1 (FM50) [3] Rear paper feed assist fan /3 (FM52)
[2] Rear paper feed assist fan /2 (FM51) [4] Front side direction
682 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[9] [10] [11] [12]
[1]
[2]
[3]
[4]
[8]
[7] [5]
[6]
fd501fs5001c
[1] Multi feed detection board /1 (MFDB1) [7] Door switch (MS1)
[2] FD entrance sensor (PS1) [8] Jam indicator board (JAMIB)
[3] Roller solenoid /1 (SD5) [9] Temperature sensor board (TSB)
[4] Roller solenoid /2 (SD6) [10] Multi feed detection board /2 (MFDB2)
[5] Roller solenoid /3 (SD7) [11] PI exit sensor (PS4)
[6] Roller solenoid /4 (SD8) [12] FD operation board (FDOB)
683
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[2]
[3]
[4]
[5]
[6]
[11]
[7]
[10] [9] [8] fd501fs5002c
684
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[3] [4]
[2]
[19]
[18]
[17]
[16]
[15]
[14]
[7] [6] [5]
[13]
[8]
[12]
[11] [10] [9] fd501fs5003c
[1] Sub tray paper full sensor (PS46) [11] Tray up down motor (M11)
[2] Paper exit solenoid (SD12) [12] L size gate solenoid (SD4)
[3] Sub tray paper exit sensor (PS16) [13] S size gate solenoid (SD3)
[4] Sub tray paper full sensor (PS17) [14] Alignment motor (M12)
[5] Main tray paper exit sensor (PS18) [15] Punch conveyance motor (M2)
[6] Main tray upper limit sensor (PS20) [16] Intermediate conveyance motor (M3)
[7] Sub tray gate solenoid (SD9) [17] Entrance gate solenoid (SD1)
[8] Main tray empty sensor (PS23) [18] Entrance conveyance motor (M1)
[9] Main tray folding paper full sensor (PS7) [19] Main tray paper exit motor (M17)
[10] Main tray lower limit sensor (PS22)
685
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
D. PI rear side
[4]
[5] fd501fs5004c
[1] Paper lift motor /Up (M8) [5] PI registration clutch /Lw (CL2)
[2] PI lift plate home sensor /Up (PS34) [6] PI conveyance sensor /Up (PS31)
[3] Paper lift motor /Lw (M9) [7] PI conveyance motor (M7)
[4] PI lift plate home sensor /Lw (PS40) [8] PI registration clutch /Up (CL1)
E. PI upper surface
[6]
[1] PI paper set sensor /Up (PS44) [7] PI paper empty sensor /Up (PS33)
[2] S size sensor /Up (PS36) [8] PI paper empty sensor /Lw (PS39)
[3] PI max paper size sensor /Up (PS47) [9] PI conveyance sensor /Lw (PS37)
[4] L size sensor /Up (PS35) [10] PI upper limit sensor /Lw (PS38)
[5] Paper size VR /Up (VR31) [11] PI upper limit sensor /Up (PS32)
[6] PI cover open/close sensor (PS43) [12] PI pick-up solenoid /Lw (SD14)
[13] PI pick-up solenoid /Up (SD13)
686
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[5] [4] [3] [2] [1] fd501fs5006c
[1] PI paper set sensor /Lw (PS45) [4] L size sensor /Lw (PS41)
[2] Paper size VR /Lw (VR32) [5] PI max paper size sensor /Lw (PS48)
[3] S size sensor /Lw (PS42)
687
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
G. Punch section
/1050e/1050eP
[1]
[12]
[11]
[10]
[9]
[2]
[8]
[3]
[1] Punch registration home sensor (PS11) [7] Punch conveyance sensor (PS5)
[2] Punch motor (M10) [8] Punch scraps box set sensor (PS12)
[3] 3 holes/4 holes home sensor (PS9) [9] Alignment plate home sensor (PS10)
[4] 2 holes punch home sensor (PS8) [10] Punch scraps full sensor (PS26)
[5] Punch registration motor (M13) [11] Folding exit sensor (PS2)
[6] Punch registration sensor (PS6) [12] Intermediate conveyance sensor (PS13)
688
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[10] [2]
[9]
[3]
[8]
[7] [4]
[1] S size conveyance sensor (PS58) [6] 1st folding release motor (M14)
[2] 2nd folding roller solenoid (SD18) [7] 2nd folding release motor (M15)
[3] Folding entrance sensor (PS52) [8] 2nd folding cam home sensor (PS56)
[4] 1st folding conveyance sensor (PS51) [9] 3rd folding release motor (M16)
[5] 1st folding cam home sensor (PS55) [10] 3rd folding cam home sensor (PS57)
689
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1] [2]
/1050e/1050eP
[6]
[5]
[4]
[3] fd501fs5009c
[1] 3rd folding conveyance sensor (PS54) [4] 2nd folding motor (M5)
[2] 2nd folding conveyance sensor (PS53) [5] Folding gate solenoid (SD15)
[3] 1st folding motor (M4) [6] 3rd folding motor (M6)
690
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[14] [15] [16] [17]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[10] [9] [8]
[1] Entrance conveyance lock solenoid (SD5) [13] Grip conveyance home sensor (PS5)
[2] Entrance sensor (PS4) [14] Relay board /1 (RLB/1)
[3] Paper press solenoid /1 (SD6) [15] Shift unit home sensor (PS11)
[4] Paper cooling fan motor /Rr (FM5) [16] Stacker tray set LED (LED1)
[5] Paper cooling fan motor /Mi (FM3) [17] Alignment plate home sensor (PS12)
[6] Paper cooling fan motor /Fr (FM1) [18] Coupling conveyance lock solenoid (SD11)
[7] Front door lock solenoid (SD4) (LS-501 only)
[8] Front door switch (MS1) [19] Paper press solenoid /2 (SD7)
[9] Hand cart set switch (RS1) [20] Alignment motor (M7)
[10] Stacker tray set sensor (PS1) [21] 2nd gate solenoid (SD10) (LS-501 only)
[11] Stacker tray upper limit sensor (PS3) [22] Coupling conveyance motor (M6) (LS-502 only)
[12] Paper detection sensor (PS19)
2 691
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. Upper surface
[1] Conveyance sensor /3 (PS17) (LS-501 only) [7] Paper cooling fan motor /1 (FM2)
[2] Jam indication board (JAMIB) [8] Stacker tray operation board (TOB)
[3] Coupling exit sensor (PS18) (LS-501 only) [9] Conveyance sensor /1 (PS7)
[4] JAM door switch (RS2) (LS-501 only) [10] Sub tray full sensor (PS9)
[5] Sub tray door sensor (PS8) [11] Sub tray exit sensor (PS10)
[6] Paper cooling fan motor /2 (FM6) [12] Conveyance sensor /2 (PS16) (LS-501 only)
692
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[20]
1050e/1050eP
[19]
[1]
[18] [2]
[17] [3]
[4]
[16]
[15] [5]
[6]
[14]
[13] [7]
[1] Shift unit motor (M5) [11] 2,000 sheets stacked sensor (PS13)
[2] Stacker tray upper limit switch (MS2) [12] Inlet (LS-501 only)
[3] Grip conveyance motor (M4) [13] Stacker tray up down motor (M1)
[4] Coupling conveyance motor (M6) (LS-501 only) [14] Stacker tray encoder sensor (PS2)
[5] LS control board (LSCB) [15] Job partition solenoid (SD2)
[6] DC power supply (DCPS) (LS-501 only) [16] 1st gate solenoid (SD1)
[7] Stacker tray lower limit switch (MS3) [17] Conveyance motor (M2)
[8] Outlet (LS-501 only) [18] Sub tray exit motor (M3)
[9] Stacker tray arm release sensor (PS15) [19] Motor cooling fan motor (FM4)
[10] 5,000 sheets stacked sensor (PS14) [20] Rear stopper solenoid (SD3)
2 693
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
D. Shift unit
[3] [4]
/1050e/1050eP
[1] Front stopper solenoid (SD9) [3] Paper press solenoid /3 (SD8)
[2] Relay board /2 (RLB/2) [4] Paper empty sensor (PS6)
694
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[4] [5]
[1]
[2]
[3] fs503fs5001c
[1] Counter reset sensor (PS15) [4] FNS drive board (FNSDB)
[2] Tray lower limit sensor (PS3) [5] FNS control board (FNSCB)
[3] Tray up down motor (M3)
695
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. Rear side 2
[2]
[3]
[1] Main tray exit motor (M7) [5] Gate solenoid (SD2)
[2] Paper exit opening solenoid (SD9) [6] Conveyance motor (M1)
[3] Paper exit opening sensor (PS12) [7] Paper exit opening motor (M8)
[4] Bypass solenoid (SD5) [8] Sub tray exit motor (M6)
C. Front side
[1]
[2]
[4]
fs503fs5003c
[1] FNS entrance sensor (PS4) [6] Staple exit upper limit sensor (PS7)
[2] Staple scraps box set sensor (PS34) [7] Tray upper limit sensor (PS2)
[3] Door switch (MS1) [8] Main tray exit sensor (PS10)
[4] Jam indication board (JAMIB) [9] Sub tray paper full sensor (PS30)
[5] Stacker entrance sensor (PS5) [10] Sub tray paper exit sensor (PS1)
696
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[8]
[2]
[7] [3]
[5] [4]
[6]
fs503fs5004c
[1] Intermediate roller open close motor (M25) [6] Paper exit arm home sensor (PS9)
[2] Stacker entrance motor (M13) [7] Stacker empty sensor (PS20)
[3] Paper exit arm motor (M23) [8] Alignment home sensor /Fr (PS31)
[4] Paddle motor (M2) [9] Intermediate roller release solenoid (SD7)
[5] Intermediate roller home sensor (PS33) [10] Alignment home sensor /Rr (PS8)
697
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
E. Stacker inside 2
/1050e/1050eP
[10]
[9]
[1]
[2]
[3]
[4]
[8]
[5]
[1] Alignment motor /Rr (M5) [6] Rear stopper motor (M26)
[2] Alignment motor /Fr (M22) [7] Stapler movement motor (M11)
[3] Stack assist guide motor (M24) [8] Stapler movement home sensor (PS11)
[4] Stack assist home sensor (PS32) [9] Stapler rotation motor (M4)
[5] Rear stopper home sensor (PS35) [10] Stapler rotation home sensor (PS14)
698
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[6]
1050e/1050eP
[5]
[1]
[4]
[2]
[3]
fs503fs5006c
[1] Stapler ready sensor /Rr (PS46) [4] Stapler board (STB)
Stapler ready sensor /Fr (PS47) [5] Staple empty sensor /Rr (PS44)
[2] Stapler home sensor /Rr (PS40) Staple empty sensor /Fr (PS45)
Stapler home sensor /Fr (PS41) [6] Stapler motor /Rr (M30)
[3] Cartridge set sensor /Rr (PS42) Stapler motor /Fr (M31)
Cartridge set sensor /Fr (PS43)
699
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
15.7 SD-501
A. Horizontal conveyance section
/1050e/1050eP
[1]
[4]
[2]
[3] 15anf5c001na
[1]
[1] Horizontal conveyance sensor /2 (PS3) [6] Roller release solenoid /4 (SD4)
[2] Horizontal conveyance exit sensor (PS4) [7] Subtray exit sensor (PS11)
[3] Horizontal conveyance motor (M2) [8] Front side direction
[4] Horizontal conveyance gate solenoid (SD3) [9] Subtray paper full sensor (PS12)
[5] Horizontal conveyance sensor /1 (PS2)
700 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[2]
[3]
[4]
[5]
[6]
15anf5c003na
[1] Right angle conveyance gate solenoid (SD2) [6] Front side direction
[2] Right angle conveyance sensor /1 (PS5) [7] Roller release solenoid /2 (SD6)
[3] Right angle conveyance motor (M6) [8] Right angle conveyance sensor /2 (PS6)
[4] Overlap motor (M13) [9] Roller release solenoid /1 (SD5)
[5] Overlap home sensor (PS17)
1 701
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
C. Folding section
(1) Top side /1
/1050e/1050eP
[10]
[1]
[9] [2]
[8]
[3]
[7]
[4]
[6]
[5]
15anf5c004na
[1] 2nd folding blade motor (M19) [6] Roller release solenoid /3 (SD7)
[2] Folding main scan alignment home sensor /Fr2 (PS49) [7] Folding sensor /2 (PS44)
[3] Folding main scan alignment home sensor /Fr1 (PS18) [8] 2nd folding blade home sensor /2 (PS23)
[4] Folding entrance sensor (PS60) [9] 2nd folding blade home sensor /1 (PS22)
[5] Front side direction [10] Folding passage sensor (PS8)
[4]
[3]
[1]
[2]
15anf5c005na
[1] Folding sub scan alignment home sensor (PS56) [3] Folding sensor /1 (PS7)
[2] Folding main scan alignment motor /Rr (M14) [4] Front side direction
702 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[12]
[2]
[7]
[3]
[1] 1st folding blade motor (M18) [7] Front side direction
[2] Folding conveyance motor (M4) [8] Folding main scan alignment motor /Fr (M7)
[3] Folding main scan alignment home sensor /Rr (PS19) [9] Folding entrance motor (M3)
[4] 1st folding blade home sensor /2 (PS21) [10] Folding sub scan alignment exit motor (M8)
[5] 1st folding blade home sensor /1 (PS20) [11] Guide shaft home sensor (PS46)
[6] Guide shaft motor (M25) [12] Folding exit home sensor (PS24)
1 703
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[4]
[1]
[2]
[3]
15anf5c007na
704 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[1]
1050e/1050eP
[2]
15anf5c008na
[1] Folding unit lock solenoid (SD8) [2] Front side direction
[1]
[2]
[3]
[4] 15anf5c009na
1 705
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[7] [1]
[6] [2]
[3]
[5]
[4]
15anf5c010na
[1] Clincher solenoid /Rt (SD9) [5] Saddle stitching paper sensor (PS13)
[2] Saddle stitching alignment motor /Rt (M9) [6] Saddle stitching alignment motor /Lt (M16)
[3] Bundle arm motor (M10) [7] Clincher solenoid /Lt (SD10)
[4] Bundle arm home sensor (PS32)
[10] [1]
[2]
[9] [3]
[4]
[5]
[8] [6]
[7] 15anf5c011na
[1] Bundle arm assist upper limit sensor (PS39) [6] Stapler movement home sensor (PS25)
[2] Saddle stitching alignment home sensor /Lt (PS29) [7] Back side direction
[3] Bundle arm assist motor (M26) [8] Clincher up down motor (M20)
[4] Stapler movement motor (M15) [9] Saddle stitching alignment home sensor /Rt (PS28)
[5] Bundle arm assist home sensor (PS38) [10] Clincher up down home sensor (PS26)
706 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[3]
1050e/1050eP
[1]
[2]
15anf5c012na
[1] Saddle stitching press home sensor (PS27) [3] Front side direction
[2] Saddle stitching press motor (M21)
(5) Stapler
[4]
[1]
[3]
[2]
15anf5c013na
[1] Stapler empty switches /Rt (SW1) and /Lt [3] Stapler home sensors /Rt (HS1) and /Lt
(SW2) (HS3)
[2] Stapler motors /Rt (M29) and /Lt (M30) [4] Clincher start sensor /Rt (HS2) and /Lt (HS4)
1 707
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[10]
[9]
[8]
[1]
[7]
[2]
[6]
[5]
[3]
[4] 15anf5c014na
[1] Bundle press movement home sensor (PS36) [6] Bundle press home sensor (PS37)
[2] Bundle sensor /4 (PS54) [7] Bundle press motor (M23)
[3] Bundle registration home sensor (PS34) [8] Bundle sensor /2 (PS15)
[4] Bottom side view [9] Front side direction
[5] Bundle press lower limit sensor (PS47) [10] Trimmer registration sensor (PS55)
708 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[7]
1050e/1050eP
[6]
[5]
[1]
[4]
[2]
[3]
15anf5c015na
[1] Bundle tray set sensor (PS58) [5] Scraps box set sensor (PS40)
[2] Trimmer scraps full sensor (PS41) [6] Scraps press home sensor (PS48)
[3] Bundle tray paper full sensor (PS61) [7] Bundle registration plate home sensor (PS16)
[4] Bundle exit sensor /2 (PS57)
F. Trimmer section
[6] [10]
[1]
[2]
[1] Trimmer press motor (M32) [6] Trimmer blade motor (M31)
[2] Trimmer paddle motor (M33) [7] Trimmer press upper limit sensor (PS52)
[3] Trimmer board replacement sensor (PS59) [8] Trimmer press home sensor (PS53)
[4] Trimmer blade home sensor (PS50) [9] Trimmer board solenoid (SD11)
[5] Trimmer blade upper limit sensor (PS51) [10] Front side direction
2 709
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
G. Left side
/1050e/1050eP
[1]
[10]
[2]
[9]
[8] [3]
[7] [4]
[6]
[5] 15anf5c017na
[1] Bundle arm rotation home sensor (PS31) [6] Bundle exit motor (M5)
[2] Bundle press stage up down limit sensor (PS45) [7] Bundle press movement motor (M17)
[3] Bundle arm rotation motor (M22) [8] Bundle registration motor (M12)
[4] Bundle press stage up down home sensor [9] Scraps removal fan motor (FM1)
(PS35) [10] Bundle press stage up down motor (M24)
[5] Left side view
710 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1]
[6] [2]
[3]
[5]
[4]
15anf5c018na
[1] Front door sensor /Rt (PS42) [4] Jam indication board /2 (JAMIB/2)
[2] Front door switch /Rt (MS1) [5] Front door sensor /Lt (PS43)
[3] Jam indication board /1 (JAMIB/1) [6] Front door switch /Lt (MS2)
1 711
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
I. Rear side
/1050e/1050eP
[1]
[9]
[2]
[3]
[4]
[5]
[8] [6]
[7]
15anf5c019na
712 1
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
(1) Front side/Top side
[1]
[2]
[7]
[3]
2 713
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[2]
[7]
[6]
[3]
[5]
[4]
a075f5c002ca
[1] Clamp entrance movement motor (M19) [6] Clamp entrance roller release motor (M20)
[2] Clamp entrance movement HP sensor (PS18) [7] SC bundle conveyance motor (M17)
[3] SC alignment motor (M15) [8] SC entrance conveyance motor (M11)
[4] FD alignment solenoid (SD11) [9] Straight gate solenoid (SD91)
[5] Clamp entrance roller release sensor (PS19)
714 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[8] [9]
[1]
[2]
[3]
[7]
[1] Clamp rotation motor (M23) [6] Clamp paper LED (LED21)
[2] Clamp rotation HP sensor (PS24) [7] Cover paper table upper limit sensor /Rr (PS26)
[3] Clamp rotation pressure sensor (PS25) [8] Clamp motor (M22)
[4] Cover paper table upper limit sensor /Fr (PS27) [9] Clamp alignment HP sensor (PS21)
[5] Clamp paper sensor (PS28)
[4]
[3] [1]
[2]
a075f5c004ca
2 715
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[9] [10]
/1050e/1050eP
[1]
[8] [7]
[6]
[2]
[5]
[4]
[3]
a075f5c005ca
[1] Pellet supply arm motor (M34) [6] Pellet count sensor (PS37)
[2] Exhaust fan /1 (M80) [7] Pellet supply motor (M33)
[3] Pellet count LED (LED32) [8] Pellet remain sensor (PS36)
[4] Pellet supply arm upper limit sensor (PS38) [9] Pellet supply door switch (MS1)
[5] Pellet supply arm lower limit sensor (PS39) [10] Pellet supply door sensor (PS40)
716 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[11] [12]
[10]
[1]
[9] [2]
[8]
[7] [4] [3]
[6] [5]
a075f5c006ca
[1] Glue tank heater (H1) [7] Glue tank up solenoid /2 (SD33)
[2] Glue apply roller heater (H2) [8] Glue tank up solenoid /1 (SD31)
[3] Glue tank temperature sensor /Lw (TH) [9] Cover paper glue up solenoid (SD32)
[4] Glue tank temperature sensor /Md (TH3) [10] Glue apply roller temperature sensor (TH1)
[5] Glue apply position detection sensor (PS32) [11] Glue tank temperature sensor /Up (TH2)
[6] Glue apply position LED (LED31) [12] Glue apply roller motor (M32)
2 717
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[2]
a075f5c007ca
[1] Glue tank movement limit sensor (PS31) [2] Glue tank HP sensor (PS33)
718 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[1] [2]
[3]
[7]
[4]
[5]
[6]
a075f5c019ca
[1] Cover paper tray upper limit sensor (PS74) [5] Cover paper tray fan /1 (M71)
[2] Cover paper conveyance sensor /1 (PS75) [6] Cover paper empty sensor (PS71)
[3] Cover paper pick up solenoid (SD71) [7] Cover paper tray fan /2 (M72)
[4] Cover paper tray knob sensor (PS82)
[1]
[2]
[1] Cover paper pick up clutch (MC71) [4] Cover paper conveyance sensor /2 (PS76)
[2] Cover paper separation clutch (MC72) [5] Cover paper conveyance sensor /3 (PS77)
[3] Cover paper tray lift motor (M73)
2 719
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1]
[14]
[2]
[13] [3]
[12]
[11]
[1] Cover paper switchback sensor (PS44) [11] Cover paper folding plate position sensor (PS51)
[2] Cover paper sensor /Rt (PS45) [12] Cover paper sensor /Lt (PS46)
[3] Cover paper lift solenoid (SD41) [13] Book exit motor (M42)
[4] Cover paper conveyance arm motor /Rt (M43) [14] Cover paper alignment HP sensor (PS41)
[5] Cover paper folding pressure sensor (PS52) [15] Cover paper conveyance arm HP sensor /Lt (PS43)
[6] Cover paper folding motor /Rt (M48) [16] Cover paper folding motor/Lt (M49)
[7] Cover paper folding plate encorder sensor (PS50) [17] Cover paper conveyance motor (M45)
[8] Cover paper alignment motor (M41) [18] Cover paper folding plate HP sensor /Rt (M48)
[9] Cover paper folding plate HP sensor /Lt (PS49) [19] Cover Paper conveyance arm HP sensor /Rt (PS42)
[10] Cover paper conveyance arm motor /Lt (M44) [20] Cutter motor (M50)
720 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
[2] [3]
1050e/1050eP
[1]
a075f5c009ca
2 721
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[1] [2]
[3]
[4]
[5]
[11]
[6]
[10]
[7]
[9] [8]
a075f5c010ca
[1] Book conveyance belt up down motor (M63) [7] Book sensor /2 (PS67)
[2] Book conveyance belt movement motor (M62) [8] Book movement motor (M64)
[3] Book conveyance belt movement HP sensor (PS62) [9] Book stopper motor (M65)
[4] Book conveyance belt motor (M61) [10] Book stopper HP sensor (PS68)
[5] Book load limit sensor (PS65) [11] Book sensor /1 (PS66)
[6] Cart set sensor (PS69)
722 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[7]
[6]
[5]
[4]
[3]
[2] [1]
a075f5c011cb
[1] Book conveyance belt lower limit sensor (PS64) [5] Book upper limit LED (LED61)
[2] Book end sensor (PS61) [6] Book door solenoid (SD61)
[3] Stacker door sensor (PS57) [7] Book conveyance belt HP sensor (PS63)
[4] Stacker door switch (MS4)
2 723
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[10]
[1]
[2]
[9]
[8]
[3]
[7]
[4]
[6]
[5]
a075f5c012cb
[1] Sub tray exit solenoid (SD4) [6] Multi feed detection board /2 (MFDTB72)
[2] Sub tray full sensor (PS5) [7] Entrance gate solenoid (SD1)
[3] Entrance sensor (PS1) [8] Entrance conveyance motor (M1)
[4] Cover paper entrance sensor (PS3) [9] Sub tray gate solenoid (SD3)
[5] Waste box full sensor (PS80) [10] Sub tray exit sensor (PS4)
724 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[8] [1]
[7]
[6]
[5]
[2]
[3]
[4]
a075f5c013ca
[1] Upper door switch (SW1) [5] Front door lock solenoid (SD80)
[2] Multi feed detection board /1 (MFDTB71) [6] Front door switch (MS2)
[3] Cover paper conveyance sensor /5 (PS79) [7] SC entrance sensor (PS2)
[4] Cover paper conveyance sensor /4 (PS78) [8] Bypass gate solenoid (SD2)
2 725
15. ELECTRICAL PARTS LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
[11]
[10]
[1]
[2]
[9]
[8]
[7]
726 2
Field Service Ver3.0 Nov.2006 15. ELECTRICAL PARTS LAYOUT DRAWING
1050e/1050eP
[3]
[2]
[1]
a075f5c015ca
[1] Cover paper table HP sensor /Fr (PS47) [3] Waste box set sensor (PS81)
[2] Cover paper table HP sensor /Rr (PS53)
2 727
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
301(W : 2 pin)
424(W : 4 pin)
210(W : 19 pin)
328(W : 6 pin)
323(W : 8 pin)
229(W : 17 pin)
326(W : 4 pin) 300(W : 2pin)
320(W : 16pin)
322(W : 5 pin) 213(W : 34 pin)
125 (W : 2 pin)
728
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
136 (W : 40 pin)
1050e/1050eP
104 (W : 4 pin) 112 (BK : 100 pin) 113 (BK : 100 pin)
111 (W : 4 pin)
137 (W : 15 pin)
420 (W : 18 pin)
35 (W : 5 pin)
36 (W : 10 pin)
411 (W : 11 pin)
410 (W : 34 pin)
729
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
620 (W : 3 pin)
622 (W : 4 pin)
528 (W : 6 : pin)
520 (W : 6 pin)
620 (W : 3 pin)
510 (GY : 2 pin) 521 (GY : 28 pin)
730
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
594 (W : 6 pin)
590 (GY : 19 pin)
596 (W : 3 pin)
2 (W : 3 pin)
76 (W : 4 pin) 75 (W : 2 pin)
77 (W : 10 pin) 71 (W : 7 pin)
74 (W : 14 pin) 73 (W : 6 pin) 1050fs5040c
731
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
4 (W : 3 pin)
2 (W : 3 pin)
1 (W : 5 pin)
1050fs5041c
732
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
650 (W : 4 pin)
651 (W : 11 pin) 1050fs5042c
1050fs5043c
733
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
(15) OB inverter
170 (W : 50 pin)
1050fs5047c
734
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
56 (GY : 24 pin)
1050fs5049c
51 (GY : 5 pin)
1050fs5050c
(20) L1 inverter
735
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
490 (W : 3 pin)
1050fs5052c
491 (W : 6 pin)
1050fs5053c
141 (W : 40 pin)
142 (W : 20 pin)
1050fs5059c
736
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
882 (BK : 160 pin)
881 (BK : 160 pin)
885 (W : 4 pin)
737
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
16.2 DF-603
16.2.1 Connector in the board
/1050e/1050eP
3 (W : 7 pin)
4 (W : 4 pin) 6 (W : 4pin) 8 (GY : 34 pin)
2 (W : 8 pin) J2 (N.C.)
9 (W : 5 pin)
1 (W : 4 pin)
10 (W : 6 pin)
17 (W : 4 pin)
14 (W : 6 pin)
11 (W : 6 pin)
B. Tray board
24 (W : 9 pin)
23 (W : 6 pin)
25 (W : 3 pin)
df603fs5008c
26 (W : 3 pin)
27 (W : 2 pin) df603fs5009c
738
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
22 (W : 2 pin)
21 (W : 3 pin) df603fs5010c
739
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
16.3 PF-701
16.3.1 Connector in the board
/1050e/1050eP
720 (W : 10 pin)
714 (W : 3 pin) 724 (W : 6 pin) 701 (W : 2 pin)
722 (W : 10 pin)
N.C.
SW1
ON
1
2
pf701fs5007c
NOTE
• Since the setting of DIP switch (SW1) is peculiar to the type, be sure not to change its setting.
740
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
A. FD control board
16 (W : 7 pin)
12 (N.C.) 8 (N.C.)
20 (W : 4 pin) 22 (N.C.)
15 (GY : 7 pin)
SW3
21 (N.C.) 5 (B : 40 pin)
2 (GY : 40 pin)
ON ON
SW3
1 2 3 4 1 2 3 4
C6500 1050
fd501fs5010c
2 741
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
215 (W : 8 pin)
211 (W : 4 pin)
506 (W : 6 pin)
742
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
313 (GY : 8 pin)
306 (GY : 18 pin)
304 (GY : 28 pin) 301 (GY : 16 pin) 302 (GY : 32 pin) fd501fs5013c
E. FD operation board
fd501fs5014c
fd501fs5015c
743
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
51 (W : 8 pin)
/1050e/1050eP
1 (W : 3 pin) fd501fs5016c
490 (W : 3 pin)
fd501fs5025c
fd501fs5026c
744
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
A. LS control board
22 (W : 2 pin) 5 (W : 9 pin)
21 (W : 4 pin) 11 (W : 6 pin)
24 (W : 12 pin) 2 (W : 15 pin)
6 (W : 3 pin) 1 (W : 13 pin)
26 (W : 5 pin)
8 (W : 8 pin)
27 (W : 4 pin)
12 (W : 6 pin) 25 (W : 6 pin) 13 (W : 7 pin)
14 (W : 2 pin)
10 (W : 10 pin)
20 (W : 4 pin)
18 (W : 7 pin)
19 (W : 3 pin) 7 (W : 14 pin)
B. Relay board /1
4 (W : 17 pin)
1 (W : 3 pin)
2 (W : 2 pin)
3 (W : 4 pin) ls502fs5006c
C. Relay board /2
4 (W : 17 pin)
1 (W : 3 pin)
2 (W : 2 pin)
3 (W : 4 pin) ls502fs5007c
745
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
D. DC power supply
/1050e/1050eP
51 (W : 6 pin)
1 (W : 5 pin)
52 (W : 2 pin)
ls502fs5008c
746
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
A. FNS control board
16 (W : 7 pin)
10 (GY : 3 pin) 12 (N.C.)
20 (W : 4 pin) 22 (GY : 20 pin)
23 (N.C.)
SW3
21 (W : 3 pin)
2 (GY : 40 pin)
ON ON
1 : ON 1 : ON
2 : ON 2 : OFF
SW3 3 : ON SW3 3 : ON
4 : ON 4 : ON
1 2 3 4 1 2 3 4
C6500 1050
fs503fs5007c
2 747
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
65 (GY : 3 pin)
56 (W : 22 pin)
64 (GY : 18 pin)
60 (W : 4 pin)
57 (GY : 40 pin)
C. Stapler board
2 (O : 3 pin) 4 (R : 3 pin)
3 (W : 3 pin) 5 (O : 3 pin)
1 (W : 7 pin)
fs503fs5009c
748
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
A. SD control board
19 (W : 4 pin)
18 (W : 2 pin)
17 (W : 8 pin) 10 (W : 3 pin) 12 (W : 8 pin) 9 (N.C.) 7 (W : 24 pin)
16 (W : 7 pin)
20 (W : 4 pin)
22 (N.C.)
SW3
24 (W : 2 pin)
23 (N.C.)
21 (N.C.)
5 (GY : 40 pin)
2 (W : 40 pin)
ON 1 : OFF ON 1 : OFF
2 : ON 2 : OFF
3 : ON 3 : ON
1 2 3 4 4 : ON 1 2 3 4 4 : ON
C6500 1050
15anf5c020nb
2 749
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. SD drive board
148 (W : 6 pin)
141 (W : 15 pin) 154 (W : 12 pin)
143 (W : 6 pin) 165 (W : 14 pin)
150 (W : 4 pin)
120 (W : 32 pin) 170 (Y : 12 pin)
169 (W : 4 pin)
167 (W : 2 pin)
122 (W : 34 pin)
166 (W : 4 pin)
110 (W : 18 pin) 168 (W : 15 pin)
750 1
Field Service Ver3.0 Nov.2006 16. CONNECTOR LAYOUT DRAWING
1050e/1050eP
A. PB control board (PBCB)
22(W:2 pin)
15(GY:40 pin)
SW1
38(W:5 pin)
7(N.C.)
VR2
16(GY:38 pin)
13(N.C.)
21(GY:6 pin)
14(N.C.)
29(W:4 pin)
8(N.C.)
3(N.C.) 19(GY:34 pin)
12(N.C.) 53(N.C)
24(N.C.)
6(N.C.) SW2 20(GY:24 pin)
2(W:7 pin) 36(GY:40 pin)
DipSW DipSW
3 4 5
B C DE
3 : OFF 3 : OFF
4 : OFF 4 : OFF
2
1 F
0
1 2 3 4 1 2 3 4
SW1 C6500 1050
a075f5c016ca
NOTE
• Do not change the SW1 setting during maintenance and repair.
2 751
16. CONNECTOR LAYOUT DRAWING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
80(GY:26 pin)
71(W:12 pin)
54(GY:40 pin) 50(W:4 pin)
70(W:12 pin)
89(N.C.) 72(W:13 pin)
82(W:8 pin)
55(GY:38 pin)
90(N.C.) 83(GY:17 pin)
60(GY:6 pin)
79(N.C.)
58(GY:34 pin) 86(W:15 pin)
85(GY:16 pin)
87(GY:24 pin)
59(GY:24 pin) 74(W:6 pin)
73(W:6 pin) 78(W:7 pin)
76(W:13 pin) 61(W:4 pin) 260(GY:2 pin)
56(GY:36 pin)
69(W:5 pin)
41(W:7 pin)
45(W:6 pin)
40(W:3 pin)
752 2
Field Service Ver3.0 Nov.2006 17. TIMING CHART
1050e/1050eP
A. A4, life size, 2 single sided originals, single sided copy (1 copy), reversed paper exit, paper feed
tray /1, line speed 490 mm/sec
Time (sec)
0 1 2 3 4 5 6 7 8 9 10 11 12 13
Item
Paper feed sensor /1 (PS7)
Pre-registration sensor /1 (PS17)
Vertical conveyance sensor /1 (PS19)
Loop sensor (PS16)
ADU deceleration sensor (PS42)
Registration sensor (PS40)
Paper leading edge sensor (PS41)
Fusing exit sensor (PS22)
ADU accelerate sensor (PS49)
Reverse sensor /1 (PS48)
Reverse sensor /2 (PS47)
ADU reverse sensor /1 (PS46)
ADU reverse sensor /2 (PS45)
ADU exit sensor (PS43)
Paper exit sensor (PS3)
1050fs5060c
753
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
B. A4, life size, 2 double sided originals, double sided copy (1 copy), straight paper exit, paper feed
tray /1, line speed 490 mm/sec
/1050e/1050eP
Time (sec)
0 1 2 3 4 5 6 7 8 9 10 11 12 13
Item
Paper feed sensor /1 (PS7)
Pre-registration sensor /1 (PS17)
Vertical conveyance sensor /1 (PS19)
Loop sensor (PS16)
ADU deceleration sensor (PS42)
Registration sensor (PS40)
Paper leading edge sensor (PS41)
Fusing exit sensor (PS22)
ADU accelerate sensor (PS49)
Reverse sensor /1 (PS48)
Reverse sensor /2 (PS47)
ADU reverse sensor /1 (PS46)
ADU reverse sensor /2 (PS45)
ADU exit sensor (PS43)
Paper exit sensor (PS3)
1050fs5061c
754
Item Time (sec) 0 1 2 3
465 mm/s
R
620 mm/s
Original paper exit motor /1 620 mm/s
(M304) F 465 mm/s
250 mm/s
250 mm/s
465 mm/s
R 550 mm/s
620 mm/s
V-VALID signal
Start button ON 1st sheet of paper 2nd sheet of paper 3rd sheet of paper scanned Exit of the 3rd
sheet of paper
df603fs5011c
scanned scanned
completed
17. TIMING CHART
755
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
756
Item Time (sec)
0 1 2 3 4 5 6 7
V-VALID signal
df603fs5012c
ON scanned
scanned scanned
Field Service Ver3.0 Nov.2006
17.3 PF-701
Field Service Ver3.0 Nov.2006
Time (sec)
A. Tray 4, A4, 2 originals
0 1 2 3 4 5
Item
Start button ON
pf701fs5008c
17. TIMING CHART
757
bizhub PRO 1050/1050P
1050e/1050eP
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
17.4 FD-501
A. Letter fold-in, A3, 2 originals, 2 copies, sub tray paper exit
/1050e/1050eP
Time (sec)
Item 0 1 2 3 4 5 6 7 8 9
758
Field Service Ver3.0 Nov.2006 17. TIMING CHART
Time (sec)
Item 0 1 2 3 4 5 6 7 8 9 10
1050e/1050eP
Main body paper exit sensor (PS3)
759
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Time (sec)
0 1 2 3 4 5 6 7 8 9
/1050e/1050eP
Item
760
Field Service Ver3.0 Nov.2006 17. TIMING CHART
Time (sec)
Item 0 1 2 3 4 5 6 7 8 9
1050e/1050eP
Main body paper exit sensor (PS3)
761
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Time (sec)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
/1050e/1050eP
Item
762
Field Service Ver3.0 Nov.2006 17. TIMING CHART
Time (sec) 0 1 2 3 4 5 6 7 8 9
Item
1050e/1050eP
Main body paper exit sensor (PS3)
763
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Time (sec) 0 1 2 3 4 5 6
/1050e/1050eP
Item
764
Field Service Ver3.0 Nov.2006 17. TIMING CHART
Time (sec) 0 1 2 3
Item
1050e/1050eP
Main body paper exit sensor (PS3)
765
bizhub PRO 1050/1050P
/1050e/1050eP
766
17. TIMING CHART
Time (sec) 0 1 2 3 4
Item
Entrance sensor (PS4)
Conveyance motor 1000 mm/s
17.5 LS-501/502
ls502fs5009c
Field Service Ver3.0 Nov.2006
Time (sec) 0 1 2 3 4
Item
Entrance sensor (PS4)
Conveyance motor 1000 mm/s
Field Service Ver3.0 Nov.2006
ls502fs5010c
17. TIMING CHART
767
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
768
17. TIMING CHART
Time (sec) 0 1 2 3 4
Item
Entrance sensor (PS4)
Conveyance motor 1000 mm/s
(M2) 490 mm/s
Sub tray exit motor 1000 mm/s
(M3) 350 mm/s
Coupling conveyance motor (M6)
Grip conveyance 1300 mm/s
motor (M4) 1000 mm/s
490 mm/s
Grip conveyance home sensor (PS5)
Alignment motor (M7)
Alignment plate home sensor (PS12)
Shift unit motor (M5)
C. A4, Sub tray mode, 3 originals, 1 copy set
ls502fs5011c
Field Service Ver3.0 Nov.2006
Time (sec) 0 1 2 3 4
Item
Entrance sensor (PS4)
Conveyance motor 1000 mm/s
Field Service Ver3.0 Nov.2006
ls502fs5012c
17. TIMING CHART
769
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
770
Time (sec)
17. TIMING CHART
Item 0 1 2 3 4 5 6
Start button ON
fs503fs5010c
Field Service Ver3.0 Nov.2006
Time (sec)
Item 1 2 3 4 5 6
fs503fs5011c
17. TIMING CHART
771
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
772
Time (sec)
Item 1 2 3 4 5 6
17. TIMING CHART
fs503fs5012c
Field Service Ver3.0 Nov.2006
17.7 SD-501
Field Service Ver3.0 Nov.2006
Time (sec)
0 1 2 3 4 5 6 7 8 9 10 11
Item
Main body paper exit sensor (PS3)
1
15anf5c800na
17. TIMING CHART
773
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
774
1
17. TIMING CHART
Time (sec)
Item 0 1 2 3 4 5 6 7 8 9 10 11
15anf5c801na
Field Service Ver3.0 Nov.2006
Field Service Ver3.0 Nov.2006 17. TIMING CHART
1050e/1050eP
Time (sec)
0 1 2 3 4 5 6 7 8 9 10 11 12
Item
15anf5c802na
1 775
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
/1050e/1050eP
Time (sec)
13 14 15 16 17 18 19 20 21 22
Item
Entrance conveyance motor (M1)
Entrance sensor (PS1)
F Right angle
conveyance motor
R (M6)
F
Overlap motor (M13)
R
15anf5c803na
776 1
Field Service Ver3.0 Nov.2006 17. TIMING CHART
1050e/1050eP
Time (sec)
Item
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
15anf5c804na
1 777
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
Time (sec)
/1050e/1050eP
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Item
Entrance sensor (PS1)
F Right angle convey-
R ance motor (M6)
F
Overlap motor (M13)
R
Right angle conveyance gate solenoid (SD2)
Right angle conveyance sensor /2 (PS6)
F Folding conveyance
R motor (M4)
15anf5c805na
778 1
17.8 PB-501
Field Service Ver3.0 Nov.2006
0 1 2 3 4 5 6 7
2
15anf5c806c
17. TIMING CHART
779
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
780
2
17. TIMING CHART
15anf5c807c
Field Service Ver3.0 Nov.2006
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
(40)
Field Service Ver3.0 Nov.2006
Book Release
Clamp
Upright
Rotation
A
Forward Backward
Positioning (alignment)
to be trimmed
Returning to HP
Positioning
(alignment)
Open Up
Down Down
Cover paper folding operation
5 seconds waiting
Positioning
(alignment)
Down of book
2
15anf5c808c
17. TIMING CHART
781
bizhub PRO 1050/1050P
1050e/1050eP
bizhub PRO 1050/1050P
/1050e/1050eP
782
2
17. TIMING CHART
0 1 2 3 4 5 6 7 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
15anf5c809c
Field Service Ver3.0 Nov.2006
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85
A
Returning
to HP
Positioning (alignment)
to be trimmed
Down
2
15anf5c810c
17. TIMING CHART
783
bizhub PRO 1050/1050P
1050e/1050eP
17. TIMING CHART Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
/1050e/1050eP
Blank page
784
I
F
E
B
A
H
D
C
59
60
58
128
41
126
51
601-6
601-5
601-4
601-3
601-2
601-1
601-7
1
1
18.1 Main body 1/4
610-1 SCAN_CLK
300
610-2 SCAN_FR Power plug
301
610-3 SCAN_W23
302
600-1 5V
Field Service Ver3.0 Nov.2006
600-6 P.G
600-5 P.G
600-2 S.G
600-4 24V
600-3 24V
610-4 SCAN_V0
303
610-5 SCAN_V1
304
610-6 SCAN_V2
305
620-1 U
610-7 LUMP_CONT
306
610-8 FAN_CONT
307
610-9 FAN_EM 620-2 V Scanner motor
308
M27
610-10 HP_PS
309
610-11 LOVRUN_PS
310
620-3 W G/Y
610-12 TOP_PS
311
631-1 632-1
FT11
FT10
610-13 ROVRUN_PS
312
623-1 24V
610-14 SCAN24V_FEM
313
631-2 632-2
18. OVERALL WIRING DIAGRAM
314
631-3 632-3
L1
CBR
L1 INVB
Circuit breaker
A
631-5
F/G
FT13
FT12
F/G
640-3-1
FT14
FT15
621-1 CONT
2
2
640-2-2
621-2 EM Scanner cooling fan
FM19
640-1-3
NF1
621-3 P.GND
Noise filter /1
650-1
FT17
FT16
622-1 5V
650-2 Scanner home
SDB
622-2 SIG
FT41
FT42
650-3 sensor
PS51
622-3 S.GND
NF2
622-4 SIG
Noise filter /2
CN19-2
CN19-1
SCANNER
CN10-5
Transformer /2
3
CN20-1
CN18-2
753-5
19
2
Dehumidification
T2
10
11
506
550
507
20
Main relay
284-1
RL1
305-5
HTR2
40
45
84
161
SW3
3
3
1
5
FT18
46
44
81
87
35
32
509
510
305-1
92
85
34
31
162
131
6
T1
CN18-1
33
30
Dehumidification heater/1 305-6
CN12-4
10
285-1 283-2
FT19
T1
T1
HTR1
285-2 305-2 Transformer /1
FT101
4
508
502
503
G
G
T2
12
T2
Triac /1
TRC2
TRC1
CN14-1
100-3 5v0
100-2 5v0
100-1 5v0
100-6 S.G
100-5 S.G
100-4 S.G
101-9 S.G
101-8 S.G
101-7 S.G
101-4 S.G
101-2 S.G
101-11 S.G
504
505
Triac /2
101-12 12V(OP)
101-3 12v(CCD)
101-1 12v(HDD)
163-7-1 665-3
101-6 5v1(IMAGE)
101-5 5v1(IMAGE)
CN137-1 APS/5V
101-10 5v1(HDD/OP)
163-6-2 665-2 APS
CN137-2 SIG
501
503
SW1
CN137-5 SIG
163-2-6 666-1 sensor /2
PS52 PS53
CN14-2
CN137-6 S.GND
163-1-7
A
SCANNER
CN137-7 LAMP_H/L
For Option
4
4
OUT
200V
Outlet
160-1-6
CN138-12 PAT1
160-2-5
CN138-13 PAT2
160-3-4
CN10-3
-3 Vpp
CN138-14 PAT3
711-1 5V1
710-1 5V1
160-4-3
-6 SGND
-5 SGND
CN10-4
CN138-15 PAT4
160-5-2
LAMP
G/Y
10
160-6-1
STATUS
-2 ROM_RXDin
-3 MONI_RXDin
INDICATOR
-5 ROM_RESET
-4 ROM_TXDout
3
11
-2 MONI_CLKout
-4 MONI_TXDout
12
709-1 FOOT_SW
703-A14 12V3 704-A1
-2 SGND
-A13 12V3 -A2
CN2-3
CN2-1
707-1 SUB_SW
-A11 SHUT_SIG -A4
SW2
30
CN72-5 S.GND
cooling fan /1
Power supply
5
5
VR
LED
FM25
-3 DATA_LED -4
36
PRCB
OB2
DATA
-6 SUB_LED -1
39
-3 VL2
-3 VL1
-7 BRT -7
715-1 VH2
714-1 VH1
48
55
CN74-11 P.GND
136-A4 SGND -A17 SGND -4 Hsync -4
59
CN74-12 P.GND
SCB
CN74-13 P.GND
136-A6 TXCLKOUT+ -A15 RXCLKIN+ -6 SGND -6
61
63
CN76-1 24v3
136-A13 TXOUT1- -A8 RXIN1- -13 R_3 -13
65
CN76-1 24v3
M4
CN76-3 P.GND
136-A15 TXOUT0+ -A6 RXIN0+ -15 R_5 -15
67
OACB 1/2
CN76-4 P.GND
136-A16 TXOUT0- -A5 RXIN0- -16 SGND -16
136-A17 SGND -A4 SGND -17 SGND -17
68
PRCB
HV1
Backlight /1
Backlight /2
71
72
CN77-8 P.GND
LCDB
CN77-10 P.GND
M1/M2/M3 FNS
-3 12V4 -3 12V4 -3 X1
315
-4 SGND -4 SGND -4 Y2
90-1
7
138-1 5v0
90-2
8
138-2 POWER_RL
138-7 REM/5
138-6 REM/4
138-5 REM/3
138-10 POWER_EM
138-9 5v0_ACOFF
138-8 HT_RL
9
9
138-3 REM/1
138-4 REM/2
138-11 5v1_ACOFF
320
319
318
317
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
24V
36V
CONT
P.GND
320
PLL_LK 170
172
316
52
62
63
CLK 171
319
315
37
318
172-9-1
172-4-6
172-7-3
172-8-2
172-6-4
172-5-5
317
173-5-1
173-5-1
173-2-4
173-1-5
173-3-3
173-4-2
1
1
18.2 Main body 2/4
131-4
131-6
131-5
131-3
131-2
131-1
Field Service Ver3.0 Nov.2006
POLYGON MOTOR
DRIVE BOARD
36pin
Amphenol
USB
M21
CN125-2 -D
CN134-9 D7
CN134-8 D6
CN134-7 D5
CN134-6 D4
CN134-5 D3
CN134-4 D2
CN134-3 D1
CN134-2 D0
CN125-3 +D
CN134-31 INIT
CN134-12 ACK
CN125-1 VBUS
CN125-4 S.GND
Sub relay
RL2
CN134-13 xFLAG
CN134-14 PBUSY
CN134-14 HBUSY
CN134-1 STROBE
CN134-33~35 N.C.
CN134-28~30 N.C.
CN134-15~18 N.C.
FT102
CN134-10 PTRCLK
CN134-36 1284ACT
CN134-32 NDVALID
7
FT22
Polygon motor
CN134-19~27 S.GND
8
192-5-9 194-9
CN132-1 INDPR
192-4-10 194-10
FT23
CN10-1
CN132-2 S.GND
192-3-11 194-11
CN10-2
WRITE UNIT
2
2
FT103
CN132-3 IND
192-2-12 194-12
CN132-4 S.GND
CN3-1
192-1-13 194-13
INDEXB
CN132-5 5V
L
Coil
191-14-1
CN130-A1 ENB
191-13-2
CN3-2
CN130-A2 ALM1
191-12-3
CN130-A3 S/HB1
191-11-4
CN130-A4 S/H1
191-10-5
CN130-A5 S.GND
191-9-6
CN130-A6 LD+5V
191-8-7
CN130-A7 LD+5V
191-7-8
CN130-A8 LPR5V
191-6-9
CN130-A9 S.GND
CN1-6
CN1-5
CN1-3
CN1-2
191-5-10
AC_NEU
AC_NEU
AC_HOT
AC_HOT
CN130-A10 -VIDEO2
191-4-11
CN130-A11 +VIDEO2
191-3-12
79
190-10-3
141
CN130-B3 DI PFU
190-9-4
142
3
3
190-7-6
82
CN11-7 12v1-2
OACB
CN130-B10 -VIDEO1
190-2-11
86
OACB 2/2
CN195- 9 D4 ADUDB1 CN21-3 P.GND
CN195-10 D11
96
CN12-4 12v2
4
4
CN 112
113
321
135-1 DF_CVR
116
CN12-20 P.GND
322
135-2 ERR_T ADUDB1
117
CN12-21 P.GND
DCPS/2
323
135-3 PVV
118
324
135-4 TNVV CN110-1 S.GND S.GND CN170-50
325
135-5 B_VV CN110-2 TG TG -49
119
CN13-1 24v1
326
M6
135-6 S_VV
5
5
CN13-2 24v1
327
135-7 5V_MON CN110-4 CLAMP CLAMP -47
328
135-8 EE_VV CN110-5 A_CLAMP ACLAMP -46
180
329
135-9 PRI_RST CN110-6 PRDKEEP PRDKEEP -45
181
330
135-10 RST_CONT CN110-7 S.GND S.GND -44
121
CN13-3 24v1
331
135-11 RXD CN110-8 +LCLK LCLK+ -43
122
CN13-4 24v1
M31 M7
FM27
332
135-12 S.GND CN110-9 -LCLK LCLK- -42
343-1
333
135-13 RTS CN110-10 S.GND S.GND -41
123
M6 CN13-6 5v2
335 135-15 ERR_R CN110-12 +RCK RCK+ -39
125
M4 CN13-7 5v2
336 135-16 TXD CN110-13 S.GND S.GND -38
126
CN13-9 5v2
cooling fan /3
Power supply
CN13-14 P.GND
CN139-1 DCD CN110-20 SEN SEN -31
133
CN13-15 P.GND
CN139-2 RXD CN110-21 SDI SDI -30
182
CN13-16 P.GND
CN139-5 GND
M6 M31 M7
CN13-17 P.GND
343-2
6
6
CN13-18 P.GND
CN 113
CN 124
CN139-9 RI
CCDB
AD_D1+ -23
CSRC I/F
CN110-28 +AD_D1
137
CN14-1 12v2
(RS232C)
CN14-2 5v2
CN110-30 -AD_D2 AD_D2- -21
139
CN111-3 RD+
CN111-4 CT CN110-33 -LVDSCLK LVDSCLK- -18 CN15-4 HT_RL
CN110-34 +LVDSCLK LVDSCLK+ -17
200
CN137-14 COVER
CN137-13 DDF_VV
CN137-12 CTS(I)
CN137-11 DTR(O)
CN137-10 TXD
CN137-9 RTS(O)
CN137-8 DSR(I)
CN137-7 RXD
PRCB
83-3
HV1
83-4
173-1-8
173-2-7
173-3-6
173-4-5
173-5-4
173-6-3
173-7-2
173-8-1
M3
83-5
M2
MS2
Interlock
switch /2
81-6
36
150 151 152 153 154 155
CN887-1 GND M1
42
CN887-2 12V
82-1
CN887-3 12Vout ADUDB1
CN887-4 GND 82-2
156 157
CN887-6 5Vout
78-1A 78-1B 79-1B 79-1A
CN 899
78-2A 78-2B 79-2B 79-2A
PCI RB
CN80-3
CN80-4
8
8
24V CN1-6
758-2
DIMM
P.GND CN1-8
758-3 CN889-5 GND CN1-9
82
5V CN1-10
758-4 CN889-6 N.C CN1-11
90
DF
S.GND CN1-12
RS232C
CN1-19
CN1-20
CN1-21
CN1-22
CN1-23
CN1-24
CN1-25
ICB
CN1-29
CN886-3 +D CN1-30
USB
CN1-31
CN886-4 S.GND CN1-32
CN1-33
CN1-34
CN1-35
CN1-36
CN1-37
CN1-38
CN1-39
CN1-40
9
9
CN888-36 1284ACT
CN888-33~35 N.C.
CN888-32 NDVALID
CN888-31 INIT
CN888-28~30 N.C.
CN888-19~27 S.GND
CN888-15~18 N.C.
CN888-14 HBUSY
CN888-13 xFLAG
CN888-12 ACK
CN888-14 PBUSY
CN888-10 PTRCLK
CN888-9 D7
CN888-8 D6
CN888-7 D5
CN888-6 D4
CN888-5 D3
CN888-4 D2
CN888-3 D1
CN888-2 D0
CN888-1 STROBE
CN885-8 CHS
CN885-7 N.C.
CN885-6 RD-
CN885-5 CT
CN885-4 CT
CN885-3 RD+
CN885-2 TD-
CN885-1 TD+
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
69
401-2 P.GND
370-1-2
326-1 P1_M24
150
401-1 24V3
Toner pump motor 370-2-1
326-2 P1_M
M28
68
301-2 P.GND
371-1-2
151
326-3 P2_M24 301-1 24V3
Air pump motor 371-2-1
326-4 P2_M
61
300-4 P.GND
57
300-3 P.GND
211-3 5V
53
300-2 24V2
Pump encoder sensor /1 211-2 SIG
300-1 24V2
118
211-1 GND
1
1
18.3 Main body 3/4
200-8 S.GND
111
86
200-7 S.GND
200-6 F_CONT
200
Pump encoder sensor /2 211-5 SIG
PS29
200-5 F_EM
201
211-4 GND
Field Service Ver3.0 Nov.2006
200-4 5V2
103
377-3-1
79
200-3 5V1
222-B9 5V
377-2-2
38
200-2 12V3
Air motor encoder sensor 222-B8 SIG
369-3 393-1-3 377-1-3 200-1 NC
222-B10 GND
380-3
TONER SUPPLY
300
324-1 24V 216-15 SCAN_CLK_O
301
324-2 24V 216-14 SCAN_FR
302
324-3 A 216-13 SCAN_MGN
Air separation motor 216-12 SCAN_CUR1
303
M10
380-7 304
324-5 B 216-11 SCAN_CUR2
380-11 305
324-6 /B 216-10 SCAN_CUR3
306
384-1-9
307
328-1 24V 216-8 SCANFAN_CONT
384-2-8
308
M11
311
216-4 NC
312
328-6 /B 216-3 NC
2
2
313
216-2 SCAN24V_FEM
381-1 383-3-1 385-1-3
216-1 S.GND
381-2 383-2-2 385-2-2
Toner remaining sensor /1 229-2 TONER_SIG
381-3 383-1-3 385-3-1
220-A1 T1_SET_P
PS31
229-3 S.GND 270-1
220-A2 5V2
270-2 Paper size
220-A3 T1SIZE_PS1
270-3
PS4
PS32
229-6 S.GND sensor /Rr1
277-1
250-3 277-2 Upper limit
TRAY1
3
390-4-9 396-4-11 220-A7 T1UP_PS
Toner remaining sensor /3 229-7 TP1_PS(30K) 277-3
250-23
220-A12 T1FEED_PS
124
S.G.
CONT 229-8 TONM_CONT
CLK 229-9 TONM_CLK 250-2
Toner bottle 220-A12 T1_0PS
-66 229-10 TONM_EM
motor -7
-88 265-1
3
3
24V 265-3
24V -11
220-A10 A5V
273-2
220-A8 T1 REMAIN_VR Remaining paper VR /1
273-3
VR1
389-1
229-11 5V2 268-1
389-2 396 9 6
Toner remaining sensor /4 229-12 TP2_PS(CUP) 250-8 268-2
389-3 Paper size VR /1
220-A11 T1SIZE_VR
268-3
VR2
5V 3392-1
92 1 349 8 1
349-8-1
-2 250-20 272-1-2
2
S.G. 320-A7 T1UPSD_CONT
-33 349-7-2
349 72 390-10-3
01 396-10-5
61 272-2-1
22
229-13 HOPM1_CONT Pick-up solenoid /1
SD3
-44 349 6 3
349-6-3 229-14 HOPM1_CLK
-5
Toner hopper 250-19
-66 349 5 4
349-5-4 229-15 HOPM1_EM 320-A6 T1 FEED CL_CONT
motor Paper feed clutch /1
320-A5 24V
F/G
F/G
229-16 TB_DOOR
Door switch /2 Paper feed
229-17 S.GND 220-A13 FAN/Fr EM
assist fan /Fr1
320-B3 T1FAN_CONT
327-1 FS_FAN_DRIVE Paper feed
4
4
220-A14 FAN/Rr EM
320-B5 P.GND
assist fan /Rr1
Transfer/separation suction fan 92-2
228-B8 FSFAN_EM
FM4
92-3 2
327-2 P.GND 320-A2 UPT1M_CONT
2 Paper lift motor /1
89-1 320-A1 UPT1M24V
5
327-3 GFAN_DRIVE
76-1-3
329-1 OP/FAN_CONT 277-1
251-3 277-2 Upper limit
TRAY2
59-3
251-2
220-B9 T2_0PS
5
5
220-B10 A5V
228-A13 MF1H/L 273-2
220-B8 T2 REMAIN_VR
CN18-3
228-B1 MF1EM
FM1
268-1
508
251-8 268-2
220-B11 T2SIZE_VR Paper size VR /2
VR4
228-B2 MF2H/L
Cooling fan /2
CN450-8
228-B3 MF2EM
FM2
251-20 272-1-2
2
320-B1 T2UPSD_CONT
Pick-up solenoid /2
TS1
228-B5 MF3EM
320-B2 24V
Paper feed clutch /2 250-24
F/G
F/G
77-1-3 171-8-6
320-B8 T2 SEP CL_CONT
FUSING UNIT
Separation clutch /2
IPB cooling fan 171-9-5
228-B6 GFAN_EM
TS2 Thermostat /2
2
FM12
171-10-4
220-B12 FAN/Fr EM
222-B3 HINF1_H/L
fan /Fr2
Suction fan /1 222-B4 HINF1_EM 251-17
FM6
171-4-10
320-B4 T2FAN_CONT
L3
L4
L2
220-B13 FAN/Rr EM
Paper feed assist
171-5-9
FM222 FM233
78-1-3 172-7-3
462-1
321-1 24V
Suction fan /3 78-2-2 172-8-2 Tray lock solenoid /1
321-2 T1LKSD_CONT
SD1
FM8
228-B12 FAN_EM
172-9-1
321-4 T2LKSD_CONT
Suction fan /4 98-2-2
FAN
254-9-5
FM29
98-3-1 222-A1 5V
222-A5 LOOP_PS Loop sensor
510
5
507
505
502
504
400-5 S.GND
410-A2 MRL_SIG 213-A16 MRL_SIG 254-10-4 253-10-4
114
400-6 P.GND
410-A3 TC_CONT 213-A15 TC_CONT 322-4 VF_MC Vertical conveyance
213-A14 TC_24FEM
VERTICAL
322-5 N.C.
CONVEYANCE
400-7 MRL_24V
410-A15 DH_OPEN
90-4 465-1
6
221-7 S.GND
sensor
410-B2 HFAN2_CONT 213-B16 HFAN2_CONT 221-6 FIX_SET_N
410-B3 HFAN_FEM 213-B15 HFAN_FEM
223-1 TH1+ Thermistor /1
410-B4 HFAN3_CONT 223-2 TH1-
410-B5 HFAN3_FEM 213-B13 HFAN3_FEM
410-B6 SFAN_CONT 213-B12 SFAN_CONT
223-3 TH2+
77A-4 410-B7 SFAN_FEM 213-B11 SFAN_FEM
223-4 TH2-
FUSING UNIT
CNT2
motor
410-B16 KEY_24FEM 213-B2 KEY_24FEM 424-2 WEBM_D2
410-B17 TC_DRV 213-B1 TCOP
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
Symbol Part name Location Symbol Part name Location Symbol Part name Location
PRCB Printer control board 1-C FM21 Paper feed assist fan /Rr1 4-B TS2 Thermostat /2 6-H
M10 Air separation motor 1-F M25 Paper lift motor /1 4-B L2 Fusing heater lamp /1 6-H
M28 Toner pump motor 1-F SW5 Door switch /2 4-F L3 Fusing heater lamp /2 6-H
M29 Air pump motor 1-F FM4 Transfer/separation suction fan 4-F L4 Fusing heater lamp /3 6-H
PS28 Pump encoder sensor /1 1-F FM5 Developing suction fan 4-F SD2 Tray lock solenoid /2 7-B
PS29 Pump encoder sensor /2 1-F PS12 Upper limit sensor /2 5-B PS16 Loop sensor 7-B
PS30 Air motor encoder sensor 1-F PS13 Paper feed sensor /2 5-B PS17 Pre-registration sensor /1 7-B
PS4 Paper size sensor /Fr1 2-B PS14 Paper empty sensor /2 5-B PS18 Pre-registration sensor /2 7-B
PS5 Paper size sensor /Rr1 2-B PS15 Handle release sensor /2 5-B PS19 Vertical conveyance sensor /1 7-B
PS6 Upper limit sensor /1 2-B VR3 Remaining paper VR /2 5-B PS20 Vertical conveyance sensor /2 7-B
M11 Intermediate hopper motor 2-F VR4 Paper size VR /2 5-B SW4 Door switch /1 7-B
PS31 Toner remaining sensor /1 2-F FM11 Pump cooling fan 5-F ACDB AC drive board 7-F
PS32 Toner remaining sensor /2 2-F FM28 Paper exit cooling fan /3 5-F FM18 Polygon cooling fan 7-F
PS33 Toner remaining sensor /3 2-F FM10 Paper exit cooling fan /2 5-F FM29 Suction fan /4 7-F
PS7 Paper feed sensor /1 3-B FM1 Cooling fan /1 5-F PS21 Vertical conveyance sensor /3 8-B
PS8 Paper empty sensor /1 3-B FM2 Cooling fan /2 5-F PS22 Fusing exit sensor 8-B
PS9 Handle release sensor /1 3-B M26 Paper lift motor /2 6-B CL1 Pre-registration clutch /1 8-B
SD3 Pick-up solenoid /1 3-B SD1 Tray lock solenoid /1 6-B CL2 Vertical conveyance clutch 8-B
VR1 Remaining paper VR /1 3-B SD4 Pick-up solenoid /2 6-B CL3 Pre-registration clutch /2 8-B
VR2 Paper size VR /1 3-B CL6 Paper feed clutch /2 6-B CNT1 Total counter 8-H
PS34 Toner remaining sensor /4 3-F CL7 Separation clutch /2 6-B CNT2 Key counter 9-I
M6 Toner bottle motor 3-G FM22 Paper feed assist fan /Fr2 6-B M24 Web motor 9-B
M7 Toner hopper motor 3-G FM23 Paper feed assist fan /Rr2 6-B PS23 Fusing jam sensor 9-B
FM9 Paper exit cooling fan /1 4-F FM3 Cooling fan /3 6-F TH1 Thermistor /1 9-B
PS10 Paper size sensor /Fr2 4-B FM8 Suction fan /3 6-F TH2 Thermistor /2 9-B
PS11 Paper size sensor /Rr2 4-B FM12 IPB cooling fan 6-F TH3 Thermistor /3 9-B
CL4 Paper feed clutch /1 4-B FM6 Suction fan /1 6-F TH4 Thermistor /4 9-B
CL5 Separation clutch /1 4-B FM7 Suction fan /2 6-F
FM20 Paper feed assist fan /Fr1 4-B TS1 Thermostat /1 6-H
I
F
E
B
A
H
D
C
G
411-1 KEY_SIG 214-11 KEY_SIG
411-2 S.GND 214-10 S.GND
411-3 CVM1_SIG 214-9 CVM1_SIG
411-4 CVFEED_SIG 214-8 CVFEED_SIG
323-8 N.C
411-5 CV_SIZE0 214-7 CV_SIZE0 341-14 353-2-10 356-1-2
323-5 CONT
214-6 CV_SIZE1 353-1-11 356-2-1 Erase lamp
EL
411-6 CV_SIZE1
411-7 CV_SIZE2 214-5 CV_SIZE2
341-13 354-2
F/G
1
1
18.4 Main body 4/4
SD5
323-3 24V solenoid
214-2 CPF0
356-9
411-10 OPF0
411-11 OPF1 214-1 CPF1
F/G
F/G
Field Service Ver3.0 Nov.2006
M22
37-2 OP_DTR 323-1 BLA_1
ACDB 2/2
36-6 SIZE 3
DRUM UNIT
Coin vendor
37-5 OP_DSR 225-A2 SIG Blade sensor /1
36-9 CPF1 341-21 355-5-5 356-5 360-3
37-6 OP_RTS 225-A3 S.GND
36-10 P.GND 355-6-4 356-6 360-1
341-22 355-7-3 356-7 360-2
539-1-5
225-A4 SIG Blade sensor /2
355-8-2 356-8 360-3
PS24 PS25
2
2
F/G
510-14 REQ1 215- 2 REQ1 353-8-4 360-3
540-3-13
510-13 REQ2 215- 3 REQ2
540-4-12 340-5 350-4-2 458-1 457-1
123
F/G
224-6 A.GND 457-4 Drum potential sensor
215- 6 ACK2
DPS
510-10 ACK2
PS26 PS27 DPSB
TRANFER
540-13-3 Drum temperature sensor
CHARGER
215-13 LATCH 340-6 351-2-3
TRANSFER/
510-3 LATCH 224-3 THD+
540-14-2
SEPARATION
SEPARATION
GUIDE PLATE
510-2 CLK_R 215-14 CLK_T
540-15-1 341-1 454-1
510-1 RXD 215-15 TXD 225-A7 5V 5V
341-2 454-2
225-A8 DCONT DCONT
560-2 325-1 24V 341-3 454-3
529-1 24V2 225-B1 Vref Vref
CN650-1 24V 531-1 24V 560-5 325-2 24V 341-4 454-4
529-2 24V2 Vertical 225-B2 Gamma CONT Gamma CONT
CN650-2 5V 531-2 5V 560-1 ADU 325-3 A 341-5 454-5
529-3 A conveyance 225-B3 JAMCONT JCONT Toner control sensor board
M8
CN651-1 TRANS G_CONT 531-3 TRANS G_CONT 560-3 accelerate 325-4 /A 341-6 454-6
529-4 /A 225-B4 DSIG DSIG
M14
CN651-2 TRANS_CONT 531-4 TRANS_CONT 560-4
motor 325-5 B 341-7 454-7
529-5 B
motor 225-B5 DmonSIG Dmon
CN651-3 TRPWM 560-6 325-6 /B 341-8 454-8
529-6 /B 225-B6 Gamma SIG Gamma SIG
CN651-4 SEP_CONT 531-5 SEP_CONT 341-9 454-9
561-2 225-B7 JAMSIG JAM
3
3
561-5 454-10
225-B8 A.GND A.GND
CN651-6 SPDC_PWM 524-2 24V2 422-2 24V
561-1
CN651-7 SHIFT SIG 531-6 SHIFT SIG 524-3 A ADU reverse Paper exit 422-3 A
561-3
M9
524-4 /A motor /1 422-4 /A
M12
CN651-8 TSDC_FB motor
F/G
561-4
422-5 B
HV2
524-5 B
110
152
102
M13
534-2-5 562-4
motor 181-5 256-3
F/G
528-5 B F/R 227-9 CHARGE2 CONT
534-1-6 562-6 181-6 159-4 256-4
528-6 B/ EM 228-A3 EM 227-8 CHARGE PWM
181-7 159-5 256-5
DEVELOPING
M3
M15
181-11 159-9
CHARGER
ADU conveyance 574-2 557-2-2 563-7 motor /1 24V 227-3 DEV BIAS FB
526-A2 SIG 520-5 B 256-10
sensor /1 574-3 557-1-3 563-11 227-2 DEV BIAS(AC) CONT
526-A1 S.GND 520-6 B/ 256-11
227-1 DEV BIAS(AC) PWM
575-1 543-3-1 255-3
GRID BIAS
526-A6 5V 182-1
5V 228-A11 5V
UNIT
PS35 PS36
526-A4 S.GND 182-3
CONT 228-A8 CONT
4
4
CHARGER
583-3
PS37
sensor 526-A7 S.GND EM 228-A10 LD 211-13 S.GND
182-7
M1
155
PS38 PS39
limit sensor 526-A13 S.GND 211-8 DOOR_PS2 Door open/close sensor /2
335-1 81-9-1 130-6-1 87-3
PS2
PS40 PS41
526-B6 S.GND 335-8 336-1-4
PRCB 2/2
47
210-16 TONER_VV
324
P.G.
335-9 336-2-3
43
325
545-2-2
110
102
PS42
526-B7 S.GND 521-A10 D1 separation
328
210-12 E_VV
5
5
571-1-10 564-1-2
548-3-1 521-A11 D2 cleaning
M20
170
solenoid
125
solenoid
336
solenoid P.G.
585-3 551-1-3 183-9
527-A10 5V P.G.
551-2-2
371-1-2
183-10
Paper feed motor
534-3 P.GND
552-1-3 212-2 R_POM_VR
586-3 527-A13 5V 180-1 158-1
468-1-4569-3-1 24V
154
553-3-1 P.G.
6
6
527-A6 P.GND
cooling fan 208-1 5V2
588-3 554-1-3 208-2 SIG
527-B4 5V
546-3-1
(OPTION)
521-A3 P.GND
cooling fan EM 219-5 LD
***-1-6 334-7
S.G.
M31
lamp
181
24V
ADU reverse paper exit motor
5V
7
7
556-2-9 573-9
521-B13 LED 755-3
91
556-1-10 573-10
S.GND
521-B14 24V 755-4
54
P.GND
755-5
76
(OPTION)
P.GND
571-8-3 559-6-1 755-6
77
521-A5 24V2 5V
571-3-8 559-1-6(A) Transfer 757-2-4
137
521-A6 A 5V
571-5-6 559-3-4(/A) assist 757-3-3
139
S.GND
M19
521-A7 /A 757-4-2
571-4-7 559-2-5(B) motor
140
521-A8 B S.GND
217-6 IO_DTXD
217-7 5V
217-8 IO_DCLK
217-9 S.GND
217-10 PFU_LATCH
217-11 IO_UCLK
217-12 ERR_OUT1
217-13 IO_URXD
217-14 ACK1
217-15 REQ13
217-1 NC
217-2 NC
217-3 ERR_OUT3
217-4 ACK3
217-5 REQ3
571-6-5 559-4-3(/B)
ADUDB1
F/G
521-A9 /B
751-10-1
751-1-10
F/G
258-12 542-12
258-11 542-11
513-2 GND
116
258-10 542-10
99
513-1 24V
258-9 542-9
500-9 A.GND
112
258-8 542-8
500-8 5VA
105
258-7 542-7
56
500-3 P.GND
258-6 542-6 523-1 LOOP ENG 590-19 LOOP ENG
8
8
500-6 S.GND
129
500-4 5V
258-2 542-2 523-6 LOOP_CLK 590-14 LOOP_CLK
500-2 12V
101
258-1 542-1
523-7 LOOP_REF1 590-13 LOOP_REF1
523-8 LOOP_REF2 590-12 LOOP_REF2
50
500-1 24V1
259-2 541-2 523-9 LOOP_REF3 590-11 LOOP_REF3
95
501-2 P.GND
259-1 541-1 523-10 CONV/2_ENG 590-10 CONV/2_ENG
502-1 541-3 259-3
156
521-A12 5V 599-5
597-1 5V 594-2 24V2
512-1 SHIELD 521-A14 S.GND 597-2 S.GND 599-2
594-1 24V2
512-2 SIG 511-1 CLK 595-1 CLK 598-6
S.GND
12V
P.GND
24V
HT
HT
P.GND
S.GND
5V
24V
592-1 24V2
94
98
597-11
96
597-7
39
89
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
Symbol Part name Location Symbol Part name Location Symbol Part name Location
EL Erase lamp 1-B — Grid bias 4-A FM14 ADU cooling fan /1 6-F
SD5 Drum claw solenoid 1-B PS1 Door open/close sensor /1 4-B FM15 ADU cooling fan /2 6-F
M22 Blade motor 1-B PS2 Door open/close sensor /2 4-B FM16 Sensor cooling fan 6-F
M23 Charger cleaning motor 1-B PS3 Paper exit sensor 4-B FM17 Registration cooling fan 6-F
— Coin vendor 1-E M1 Fusing motor 4-E TSL Transfer exposure lamp 6-F
PS24 Blade sensor /1 2-B M15 ADU conveyance motor /1 4-F PS46 ADU reverse sensor /1 6-I
PS25 Blade sensor /2 2-B PS35 ADU conveyance sensor /1 4-I PS47 Reverse sensor /2 6-I
PS26 Charger cleaning home sensor 2-B PS36 ADU conveyance sensor /2 4-I PS48 Reverse sensor /1 6-I
PS27 Charger cleaning limit sensor 2-B PS37 Transfer assist home sensor 4-I PS49 ADU accelerate sensor 6-I
DPS Drum potential sensor 2-B PS38 Transfer/separation cleaning home sensor 4-I PS50 ADU reverse paper exit sensor 6-I
DPSB Drum potential sensor board 2-B PS39 Transfer/separation cleaning limit sensor 4-I — Transfer assist adapter 6-I
TH5 Drum temperature sensor 2-B RCDB Recycle cut drive board 5-A PS54 Centering sensor 7-F
ADUDB1 ADU drive board /1 2-G M4 Paper feed motor 5-E M19 Transfer assist motor 7-F
— Transfer bias 2-I M5 Conveyance motor 5-E ADUDB2 ADU drive board /2 8-F
— Guide plate bias 2-I M20 Transfer/separation cleaning motor 5-F M16 ADU conveyance motor /2 9-E
— Separation bias 2-I SD6 ADU lock solenoid 5-F M17 Registration motor 9-E
— Transfer/separation charger 2-I SD7 Reverse/exit solenoid 5-F M18 Loop motor 9-E
— Developing bias 3-A SD8 Thick paper assist solenoid 5-F MFDB1 Multi feed detection board /1 9-G
TCSB Toner control sensor board 3-B PS40 Registration sensor 5-I MFDB2 Multi feed detection board /2 9-H
HV1 High voltage unit /1 3-B PS41 Paper leading edge sensor 5-I
M3 Developing motor 3-E PS42 ADU deceleration sensor 5-I
M8 Vertical conveyance motor 3-E PS43 ADU exit sensor 5-I
M9 Paper exit motor /1 3-E PS44 ADU handle release sensor 5-I
M12 ADU reverse motor 3-F PS45 ADU reverse sensor /2 5-I
M13 Reverse/exit motor 3-F M30 Recycle cut motor 6-A
M14 ADU accelerate motor 3-F M2 Drum motor 6-E
HV2 High voltage unit /2 3-I M31 ADU reverse paper exit motor 6-E
— Charger 4-A FM13 ADU cooling fan /3 6-F
Field Service Ver3.0 Nov.2006 18. OVERALL WIRING DIAGRAM
1 2 3 4 5 6 7 8 9
1050e/1050eP
A MFS1
A
To MAIN BODY Multi feed sensor/1
MFDB1
MFDB2
MFS2
SD303 Gate solenoid
C Multi feed sensor/2 C
Tray lower limit sensor PS316
TB
Original size sensor/Lt PS303
Reverse jam
Tray upper limit sensor PS315 sensor PS304
H RADFCB Symbol H
Centering LED sensor/Fr PS319
1 2 3 4 5 6 7 8 9
18. OVERALL WIRING DIAGRAM Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
H
D
C
G
18.6 PF-701
1
1
Field Service Ver3.0 Nov.2006
753-1
CN700-1 24V1
753-2
CN700-5 5V1
753-3
CN700-6 S.GND
753-4 751-1-10
CN700-2 P.GND 705-10 RXD_DN 217-6 IO_DTXD
751-2-9 217-7 5V
705-9 5V
N.C CN700-3 P.GND 751-3-8
Dehumidification heater/1 705-8 CLK_DN 217-8 IO_DCLK
751-4-7 217-9 S.GND
795-1 795-2 705-7 S.GND
751-5-6 217-10 PFU_LATCH
HTR 1 705-6 /LATCH_DN
751-6-5 217-11 IO_UCLK
705-5 CLK_UP
751-7-4 217-12 ERR_OUT1
705-4 /ERR_GA
Dehumidification heater/2 751-8-3 217-13 IO_URXD
705-3 TXD_UP
753-5 796-1 796-2 751-9-2
705-2 /ACK_GA 217-14 ACK1
HTR 2 751-10-1
705-1 /REQ_GA 217-15 REQ13
Dehumidification heater
HTR 3 752-3-3 217-3 ERR_OUT3
705-13 /IO ERR
752-4-2 217-4 ACK3
753-6 705-12 /IO ACK
752-5-1
3
705-11 /IO REQ 217-5 REQ3
MAIN BODY
2
2
Door switch
770-1 775-1
SW10
754-1 FT1 FT2
770-2 775-2
CN701-1 24V2(I/L)
1
24V
2
760-12
710-2 T1_SET_P
760-14
3
760-22
710-8 S.GND
Paper Paper
4
feed M feed M
P.GND
754-2
CN701-2 P.GND
263-1-6 277-1
760-3 263-2-5 277-2 Upper limit
710-5 /T1UP_PS
PS71
754-4
CN700-7 S.GND 760-23 263-5-2 276-2 Paper feed
710-3 /T1FEED_PS
PS72
PS89
sensor /1 730-3 745-1-12
CN712-1 S.GND 760-4 265-2 Handle release
710-6 /T1GRIP_PS
3
3
265-3
PS74
731-1 745-6-7
sensor /1
CN712-6 5V1 270-1
Vertical conveyance 731-2 745-5-8
CN712-5 /T1_CONV_PS 760-11 270-2 Paper size
PS90
sensor /1 731-3 745-4-9 710-14 T1SIZE_PS1
CN712-4 S.GND 270-3
PS75
sensor /Fr1
732-1 745-9-4 271-1
CN712-9 5V1 760-6 271-2 Paper size
Intermediate 732-2 745-8-5 710-13 T1SIZE_PS2
CN712-8 /T1_CONV_MID_PS
PS76
271-3
PS91
sensor /Up 732-3 745-7-6 sensor /Rr1
CN712-7 S.GND
760-7 273-1
733-1 745-12-1 710-9 A5V
CN712-12 5V1 760-5 273-2 Remaining
733-2 745-11-2 710-7 T1REMAIN_VR
273-3
VR10
PS92
733-3 745-10-3
CN712-10 S.GND 268-1
760-8 268-2 760-24
710-10 T1SIZE_VR
F/G
CN713-15 5V1
F/G
PS93
734-3 746-4-3 272-1-2
sensor /2 CN713-13 S.GND 760-20
720-3 /T1UPSD_CONT Pick-up
272-2-1
735-1 746-3-4 solenoid /1
CN713-12 5V1
735-2 746-2-5 760-19 260-1-2
Loop sensor /2 CN713-11 /T2_LOOP_PS 720-2 /T1FEEDCL_CONT Paper feed
260-2-1
PS94
735-3 746-1-6 760-15
SD14 CL6
PS95
736-3 747-3-3
Vertical conveyance
sensor /3 CN717-8 S.GND
737-1 744-3-7
CN713-3 5V1
Vertical conveyance 737-2 744-2-8 262-3-1 267-3-1(CONT)
4
4
CN713-2 /T3_CONV_PS
262-2-2 267-2-2(EM)
PS96
sensor /1 737-3 744-1-9 760-10 Paper feed
CN713-1 S.GND 710-11 /FAN_F_EM
262-1-3 267-1-3(GND) assist fan /Fr1
738-1 744-6-4 760-17 261-3-1 266-3-1(CONT)
CN713-6 5V1 720-4 T1FAN_CONT
Intermediate 738-2 744-5-5 760-9 261-2-2 266-2-2(EM) Paper feed
CN713-5 /T3_CONV_MID_PS 710-12 /FAN_R_EM
PS97
FM41 FM42
sensor /Lw 738-3 744-4-6 760-21 261-1-3 266-1-3(GND) assist fan /Rr1
CN713-4 S.GND 720-6 P.GND
760-13 278-1(CONT)
739-1 744-9-1 720-8 UPM_CONT
CN713-9 5V1 760-1 278-2(24V) Paper lift motor /1
M42
PS98
739-3 744-7-3
CN713-7 S.GND
790-2-1 795-3-1(CONT)
720-5 T1FAN_CONT
795-2-2(EM)
790-1-2 795-1-3(GND)
FM50
assist fan /1
765-1-2
Pre-registration CN722-1 24V1
Rear paper feed
765-2-1
CL1
766-1-2 761-22
Intermediate CN722-3 24V1 711-A8 S.GND
766-2-1
CL2
5
5
PS78
Paper size VR /2
3
268-3
VR13
F/G
782-1024V 781-2
1
761-20 272-1-2
782-1124V 781-1 721-A3 /T2UPSD_CONT
2
272-2-1
Pick-up
solenoid /2
761-19 260-1-2
721-A2 /T2FEEDCL_CONT Paper feed
761-15 260-2-1
721-A1 24V1 clutch /2
6
6
791-2-1 796-3-1(CONT)
721-A4 T2FAN_CONT
796-2-2(EM)
791-1-2 796-1-3(GND)
FM51
721-A7 P.GND
assist fan /2
Rear paper feed
762-12
711-B2 T3_SET_P
762-14
711-B1 5V1
723-1 A 748-3
CN723-3 A
723-2 24V 748-1 762-22
PF exit CN723-1 24V2(I/L) 711-B8 S.GND
723-3 /A 748-4
7
7
CN723-4 /A
conveyance 723-4 B 748-5
M41
263-6-1 276-3
762-23 263-5-2 276-2 Paper feed
711-B3 /T3FEED_PS
PS84
724-3 749-1-5
sensor CN717-1 S.GND 270-1
762-11 270-2 Paper size
Symbol
711-B14 T3SIZE_PS1
Exit conveyance
PS87
711-B9 A5V
729-4-1 762-5 273-2 Remaining paper
CN716-4 PGND
Connector
711-B7 T3REMAIN_VR
273-3
VR14
VR /3
268-1
762-8 268-2 762-24
711-B10 T3SIZE_VR
F/G
268-3
Paper size VR /3
VR15
F/G
8
8
762-20 272-1-2
721-B3 /T3UPSD_CONT Pick-up
272-2-1
solenoid /3
762-19 260-1-2
721-B2 /T3FEEDCL_CONT Paper feed
762-15 260-2-1
779-1 744-1-3 721-B1 24V1
CN714-1 5V1 clutch /3
Door open/close 779-2 744-2-2
CN714-2 /FRONTDOOR_PS 762-18 266-1-2
Relay connector
Faston
721-B10 T3HNDLNGCL_CONT
PS70
clutch /3
782-1 773-1-6
CN724-1 24V1
Tray lock solenoid /1 782-2 773-2-5
CN724-2 /T1_LOCKSD_CONT
SD10
262-3-1 267-3-1(CONT)
762-10 262-2-2 267-2-2(EM) Paper feed
783-1 773-3-4 711-B11 /FAN_F_EM
FM45
721-B9 UPM_CONT
762-1 278-2(24V)
M44
721-B8 UPM24V
Paper lift motor /3
792-2-1 797-3-1(CONT)
721-B4 T3FAN_CONT
797-2-2(EM)
792-1-2 797-1-3(GND)
FM52
721-B7 P.GND
assist fan /3
9
9
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
CN505- 5 M4_B CN530- 1 YEL
CN505- 1 M4_24V CN530- 2 BLK
CN505- 6 M4_ B/ CN530- 3 RED
CN530- 4 ORG
M4
CN505- 3 M4_A CN530- 5 WIT
1st folding motor
CN505- 2 M4_24V CN530- 6 BLU
CN505- 4 M4_A/
M5
CN505- 9 M5_A CN531- 5 WIT
CN505- 8 M5_24V CN531- 6 BLU
CN505- 10 M5_A/
510-16A-1A
CN3- 1 KCOUT_41 CN503-16 KCOUT_41
510-15A-2A
CN3- 2 KCOUT_42 CN503-15 KCOUT_42 CN532- 1 YEL
Power plug
510-14A-3A CN506- 5 M6_B CN532- 2 BLK
CN3- 3 KCOUT_43 CN503-14 KCOUT_43 CN506- 1 M6_24V
510-13A-4A CN532- 3 RED
CN3- 4 KCOUT_44 CN503-13 KCOUT_44 CN506- 6 M6_B/ CN532- 4 ORG
510-12A-5A CN506- 3 M6_A 3rd folding motor
M6
CN3- 5 KCOUT_45 CN503-12 KCOUT_45 CN532- 5 WIT
510-11A-6A CN506- 2 M6_24V
CN3- 6 KCOUT_46 CN503-11 KCOUT_46 CN532- 6 BLU
510-10A-7A CN506- 4 M6_A/
CN3- 7 KCOUT_47 CN503-10 KCOUT_47
CN3- 8 KCOUT_48 510-9A-8A
CN503- 9 KCOUT_48
1
1
510-8A-9A
CN3- 9 KCOUT_49 CN503- 8 KCOUT_49 CN533-6- 1 RED
510-7A-10A
CN3-10 KCOUT_50 CN503- 7 KCOUT_50 CN508-A 1 M14_24V CN533-5- 2 RED
510-6A-11A
CN3-11 KCOUT_51 CN503- 6 KCOUT_51 CN508-A 2 M14_24V CN533-4- 3 BLK
510-5A-12A CN508-A 3 M14_A
Inlet
CN3-12 KCOUT_52 CN503- 5 KCOUT_52 CN508-A 4 M14_A/ CN533-3- 4 BLN 1st folding release motor
510-4A-13A
M14
CN3-13 KCOUT_53 CN503- 4 KCOUT_53 CN508-A 5 M14_B CN533-2- 5 ORG
510-3A-14A CN533-1- 6 YEL
CN3-14 KCOUT_54 CN503- 3 KCOUT_54 CN508-A 6 M14_B/
510-2A-15A
FT2
FT1
CN3-15 KCOUT_55 CN503- 2 KCOUT_55
CN3-16 KCOUT_56 510-1A-16A CN503- 1 KCOUT_56
CN508-A 7 M15_24V CN534-6- 1 RED
CN534-5- 2 RED
Field Service Ver3.0 Nov.2006
Y/G
WIT
BLK
CN13-1 /CPUIN_1(IRQ4) CN222-9 /CPUIN_1(IRQ4) 511-15A-1A CN535-6- 1 RED
CN209-A 1 KCIN_24 CN501-A17 PS51_SIG CN508-A13 M16_24V
RT1
CN13-2 /CPUIN_2(IRQ3) CN222-8 /CPUIN_2(IRQ3) 511-14A-2A CN535-5- 2 RED
CN209-A 2 KCIN_25 CN501-A16 PS52_SIG CN508-A14 M16_24V CN535-4- 3 BLK
CN13-3 CPUIN_3(IRQ1) CN222-7 CPUIN_3(IRQ1) 511-13A-3A
CN209-A 3 KCIN_26 CN501-A15 PS53_SIG CN508-A15 M16_A CN535-3- 4 BLN
CN13-4 CPUIN_4(TIM Input) CN222-6 CPUIN_4(TIM Input) 511-12A-4A M16_A/ 3rd folding release motor
M16
FT4
FT3
511-6A-10A CN508-B 2
CN209-A10 KCOUT_74 511-5A-11A
CN501-A 8 M4_CONT2
CN209-A11 KCOUT_75 CN501-A 7 M4_F/R CN508-B 3 5V CN517- 3
511-4A-12A CN508-B 4 SGND
CN209-A12 KCOUT_76 CN501-A 6 M4_RESET CN508-B CN517- 2
CN2-A 1 KCOUT_1 CN201-A20 KCOUT_1 511-3A-13A 5 PS57 SIG CN517- 1 PS57 3rd folding cam home sensor
CN2-A 2 KCOUT_2 CN201-A19 KCOUT_2 CN209-A13 SGND 511-2A-14A
CN501-A 5 SGND CN508-B 6 5V
CBR2
CBR1
CN2-A 3 KCOUT_3 CN201-A18 KCOUT_3 CN209-A14 SGND 511-1A-15A
CN501-A 4 SGND
CN2-A 4 KCOUT_4 CN201-A17 KCOUT_4 CN209-A15 SGND 511-1A-15A
CN501-A 3 SGND
CN209-A16 SGND CN501-A 2 SGND
FT6
FT5
CN2-A 5 KCOUT_5 CN201-A16 KCOUT_5 511-1A-15A CN516- 3
CN209-A17 5V CN501-A 1 5V CN508-B 7 SGND CN516- 2
CN2-A 6 KCOUT_6 CN201-A15 KCOUT_6 511-15B-1B 8 PS56 SIG 2nd folding cam home sensor
CN201-A14 KCOUT_7 CN209-B 1 KCOUT_77 CN501-B17 M4_ENBLECN508-B CN516- 1 PS56
CN2-A 7 KCOUT_7 511-14B-2B CN508-B 9 5V
Circuit breaker/2
Circuit breaker/1
CN201-A13 KCOUT_8 CN209-B 2 KCOUT_78 CN501-B16 M5_CONT1
CN2-A 8 KCOUT_8 511-13B-3B
CN201-A12 KCOUT_9 CN209-B 3 KCOUT_79 CN501-B15 M5_CONT2
WIT
CN2-A 9 KCOUT_9 511-12B-4B
BLK
CN2-A10 KCOUT_10 CN201-A11 KCOUT_10 CN209-B 4 KCOUT_80 511-11B-5B
CN501-B14 M5_F/R
CN10-1 IRQ4 CN515- 3
CN2-A11 KCOUT_11 CN201-A10 KCOUT_11 CN209-B 5 KCOUT_81 511-10B-6B
CN501-B13 M5_RESET CN508-B10 SGND CN515- 2
CN10-2 /IRQ3 CN209-B 6 KCOUT_82 CN501-B12 M5_ENBLECN508-B11 PS55 SIG 1st folding cam home sensor
CN2-A12 KCOUT_12 CN201-A 9 KCOUT_12 511-9B-7B CN515- 1 PS55
CN10-3 IRQ CN209-B 7 KCOUT_83 CN501-B11 M6_CONT1 CN508-B12 5V
CN2-A13 KCOUT_13 CN201-A 8 KCOUT_13 511-8B-8B
CN209-B 8 KCOUT_84 CN501-B10 M6_CONT2
Interrupt
CN2-A14 KCOUT_14 CN201-A 7 KCOUT_14 511-7B-9B
CN2-A15 KCOUT_15 CN201-A 6 KCOUT_15 CN209-B 9 KCOUT_85 511-6B-10B
CN501-B 9 M6_F/R
CN501-B 8 M6_RESET CN508-B13 SGND CN514- 3
CN2-A16 KCOUT_16 CN201-A 5 KCOUT_16 CN209-B10 KCOUT_86 511-5B-11B CN514- 2
FT8
FT7
CN2-A17 KCOUT_17 CN201-A 4 KCOUT_17 CN209-B11 KCOUT_87 511-4B-12B
CN501-B 7 M6_ENBLE CN508-B14 PS54 SIG 3rd folding conveyance sensor
CN514- 1 PS54
CN201-A 3 KCOUT_18 CN209-B12 5V CN501-B 6 5V CN508-B15 5V
CN2-A18 KCOUT_18 511-3B-13B
4
3
2
2
NF1
2
1
CN23-2 TDO3 CN2-B 1 KCOUT_21 CN201-B20 KCOUT_21 CN209-B15 TIME0 511-1B-15B
CN501-B 3 M4_CLK CN511- 3
CN23-3 TDI CN209-B16 TIME2 CN501-B 2 M5_CLK CN508-B16 SGND CN511- 2
CN2-B 2 KCOUT_22 CN201-B19 KCOUT_22 511-1B-15B 1st folding conveyance sensor
CN23-4 TMS CN209-B17 TIME3 CN501-B 1 M6_CLK CN508-B17 PS51 SIG CN511- 1 PS51
FT9
CN2-B 3 KCOUT_23 CN201-B18 KCOUT_23 CN508-B18 5V
JTAG
FT10
CN23-5 TRST CN2-B 4 KCOUT_24 CN201-B17 KCOUT_24
CN2-B 5 KCOUT_25 CN201-B16 KCOUT_25
CN2-B 6 KCOUT_26 CN201-B15 KCOUT_26
CN201-B14 KCOUT_27
WIT
CN2-B 7 KCOUT_27 512-1-1
BLK
CN500- 1 24VDC
Outlet
CN2-B 8 KCOUT_28 CN201-B13 KCOUT_28 512-2-2 CN513- 3
CN500- 2 24VDC CN507- 1 SGND CN513- 2
CN2-B 9 KCOUT_29 CN201-B12 KCOUT_29 512-3-3 CN507- 2 PS53 SIG
8 10
512-4-4 CN500- 3 PGND CN513- 1 PS53 2nd folding conveyance sensor
CN507- 3 5V
9 11
CN2-B10 KCOUT_30 CN201-B11 KCOUT_30 CN500- 2 PGND
CN24-1 5V CN2-B11 KCOUT_31 CN201-B10 KCOUT_31
CN24-2 RL_CONT CN2-B12 KCOUT_32 CN201-B 9 KCOUT_32
Relay
CN2-B13 KCOUT_33 CN201-B 8 KCOUT_33 CN512- 3
CN2-B14 KCOUT_34 CN201-B 7 KCOUT_34 CN507- 4 SGND CN512- 2
Y/G
WIT
BLK
CN216-12 M12_24V CN52- 2 CN507- 5 PS52 SIG
CN182- 1
BLK PGC1 BLK CN2-B15 KCOUT_35 CN201-B 6 KCOUT_35 CN52- 5 CN512- 1 PS52 Folding entrance sensor
CN507- 6 5V
CN181- 1
CN2-B16 KCOUT_36 CN201-B 5 KCOUT_36 CN216-11 M12_24V
CN216-10 M12_A CN52- 1 Punch conveyance
PGC2 WIT CN2-B17 KCOUT_37 CN201-B 4 KCOUT_37 CN216- 9 M 2_A/ CN52- 3
M2
To 5V (CCP)
CN201-B 1 KCOUT_40 CN536- 1
CN2-B20 KCOUT_40 CN507- 7 SD18_DRV CN536- 2
CN62- 2
RT5
CN216- 6 M12_24V CN507- 8 SD_24V SD18 2nd folding roller solenoid
CN182- 2
CN181- 2
CN216- 5 M12_24V CN62- 5
WIT
CN216- 4 M12_A CN62- 1
CN216- 3 M12_A/ CN62- 3 Alignment motor
M12
BLK FT11
CN1-A 2 KCIN_2 CN202-A15 KCIN_2 CN216- 1 M12_B/ CN507- 9 SD15_DRV CN536- 1
CN151- 1
RED CN1-A 3 KCIN_3 CN202-A14 KCIN_3 CN507-10 SD_24V CN536- 2 SD15 Folding gate solenoid
A
CN1-A 4 KCIN_4 CN202-A13 KCIN_4
CN1-A 5 KCIN_5 CN202-A12 KCIN_5 CN217- 1 M11 DRV1 CN61- 1 RED Tray up down
CN1-A 6 KCIN_6 CN202-A11 KCIN_6 CN61- 2 BLU
FDB
RL1
CN1-A 7 KCIN_7 CN202-A10 KCIN_7 motor
B
CN1-A 8 KCIN_8 CN202-A 9 KCIN_8
B
CN151- 2
CN517- 3
CN1-A11 KCIN_11 CN202-A 6 KCIN_11 CN507-13 SGND CN517- 2 S size conveyance
CN183- 1
WIT
CN33- 3 CN507-14 PS57 SIG
CN1-A12 KCIN_12 CN202-A 5 KCIN_12 CN224- 5 5V CN517- 1 PS58
FT12 BLK
CN217- 6 PS13_SIG CN33- 2 Main tray lower CN507-15 5V
CN1-A13 KCIN_13 CN202-A 4 KCIN_13 CN33- 1 PS22 sensor
CN1-A14 KCIN_14 CN202-A 3 KCIN_14 CN217- 7 SGND limit sensor
CN1-A15 KCIN_15 CN202-A 2 KCIN_15
WIT
BLK
CN1-A16 KCIN_16 CN202-A 1 KCIN_16
CN1-B 1 KCIN_17 CN202-B16 KCIN_17
CN1-B 2 KCIN_18 CN202-B15 KCIN_18
CN183- 2
3
3
CN183-A2
CN183-A1
CN1-B 6 KCIN_22 CN202-B11 KCIN_22 CN219-A13 5V CN51- 1
CN1-B 7 KCIN_23 CN202-B10 KCIN_23 CN219-A12 SGND CN51- 2
CN51- 3
MS1
CN1-B 8 KCIN_24 CN202-B 9 KCIN_24 CN219-A11 M1_CONT CN51- 4
CN1-B 9 KCIN_25 CN202-B 8 KCIN_25 CN219-A10 M1_CLK CN51- 5
Crimp
CN219-A 9 M1_F/R
Symbol
CN183-B2
CN183-B1
CN51- 7
M1
WIT
CN183- 1
CN1-B12 KCIN_28 CN202-B 5 KCIN_28 CN219-A 6 PGND
WIT
BLK
CN219-A 5 PGND CN51- 9
CN1-B13 KCIN_29 CN202-B 4 KCIN_29 CN51-10
CN1-B14 KCIN_30 CN202-B 3 KCIN_30 CN219-A 4 24V CN51-11
CN219-A 3 24V
CN1-B15 KCIN_31 CN202-B 2 KCIN_31
CN1-B16 KCIN_32 CN202-B 1 KCIN_32
CN219-A 2 SD12_24V CN82- 1 RED
CN219-A 1 SD12_DRV CN82- 2 BLU SD12 Paper exit solenoid
CN183- 2
CN5-A 1 KCOUT_57 CN204-A20 KCOUT_57
CN5-A 2 KCOUT_58 CN204-A19 KCOUT_58
CN5-A 3 KCOUT_59 CN204-A18 KCOUT_59 CN67- 1
CN5-A 4 KCOUT_60 CN204-A17 KCOUT_60 CN219-B13 5V CN37- 2
CN219-B12 SGND CN67- 3
CN5-A 5 KCOUT_61 CN204-A16 KCOUT_61 CN219-B11 M17_CONT CN67- 4
CN5-A 6 KCOUT_62 CN204-A15 KCOUT_62 CN219-B10 M17_CLK CN67- 5
Connector
CN219-B 9 M17_F/R
RT2
CN5-A 7 KCOUT_63 CN204-A14 KCOUT_63 CN67- 6
CN5-A 8 KCOUT_64 CN204-A13 KCOUT_64 CN219-B 8 M17_LD CN67- 7 Main tray paper exit motor
M17
Y/G
CN5-A11 KCOUT_67 CN219-B 4 24V
WIT
BLK
CN67-11
CN5-A12 KCOUT_68 CN204-A 9 KCOUT_68 CN219-B 3 24V
CN5-A13 KCOUT_69 CN204-A 8 KCOUT_69
CN5-A14 KCOUT_70 CN204-A 7 KCOUT_70 CN219-B 2 SD24V_2
CN5-A15 KCOUT_71 CN204-A 6 KCOUT_71 CN219-B 1 SD7_DRV
CN5-A16 KCOUT_72 CN204-A 5 KCOUT_72
:line(L)
CN5-A17 KCOUT_73 CN204-A 4 KCOUT_73
CN184-3
CN184-1
CN184-5
CN5-A18 KCOUT_74 CN204-A 3 KCOUT_74 CN37- 3
:neutral(N)
CN220-A 1 SGND CN37- 2
:frame GND
CN5-A19 KCOUT_75 CN204-A 2 KCOUT_75 CN220-A 2 PS17_SIG
CN5-A20 KCOUT_76 CN204-A 1 KCOUT_76 CN37- 1 PS17 Sub tray paper full sensor
CN220-A 3 5V
CN5-B 1 KCOUT_77 CN204-B20 KCOUT_77
CN5-B 2 KCOUT_78 CN204-B19 KCOUT_78
CN5-B 3 KCOUT_79 CN204-B18 KCOUT_79 CN36- 3
CN204-B17 KCOUT_80 CN220-A 4 SGND CN36- 2
CN5-B 4 KCOUT_80 CN220-A 5 PS16_SIG
Relay connector
DCPS
CN5-B 5 KCOUT_81 CN204-B16 KCOUT_81
Faston
CN220-A 6 5V
CN5-B 6 KCOUT_82 CN204-B15 KCOUT_82
CN5-B 7 KCOUT_83 CN204-B14 KCOUT_83
4
4
:-V/PGND
CN191-1
:-V/PGND
CN191-2
:-V/PGND
CN191-3
:-V/PGND
CN191-4
:+V/24V
CN191-5
:+V/24V
CN191-6
:+V/24V
CN191-7
:+V/24V
CN191-8
CN5-B10 KCOUT_86 CN204-B11 KCOUT_86 CN220-A 9 5V
CN5-B11 KCOUT_87 CN204-B10 KCOUT_87
CN5-B12 KCOUT_88 CN204-B 9 KCOUT_88
CN5-B13 KCOUT_89 CN204-B 8 KCOUT_89 CN21- 3
CN204-B 7 KCOUT_90 CN220-A10 SGND CN21- 2
CN5-B14 KCOUT_90 CN220-A11 PS1_SIG FD entrance sensor
CN5-B15 KCOUT_91 CN204-B 6 KCOUT_91 CN21- 1 PS1
CN220-A12 5V
CN5-B16 KCOUT_92 CN204-B 5 KCOUT_92
CN5-B17 KCOUT_93 CN204-B 4 KCOUT_93
CN5-B18 KCOUT_94 CN204-B 3 KCOUT_94
CN5-B19 KCOUT_95 CN204-B 2 KCOUT_95 CN220-B12 5V CN53- 1
CN5-B20 KCOUT_96 CN204-B 1 KCOUT_96 CN220-B11 SGND CN53- 2
CN220-B10 M3_CONT CN53- 3
CN220-B 9 M3_CLK CN53- 4
CN220-B 8 M3_F/R CN53- 5 CN311-A13 OP_LED12 CN361-A 1 OP_LED12
CN220-B 7 M3_LD CN53- 6 Intermediate CN311-A12 OP_LED13
CN53- 7 CN361-A 2 OP_LED13
M3
4
CN14-14 TIME_13 CN203- 5 TIME_13
FDCB
5
3
2
1
CN14-16 TIME_15 CN203- 3 TIME_15 CN311-B 9 OP_LED 3
CN32- 3 CN361-B 5 OP_LED 3
CN14-17 TIME_16 CN203- 2 TIME_16 CN222- 4 SGND
PDB
CN20-4 S.GND CN222- 7 SGND CN30- 2 Alignment plate home CN311-B 3 OP_LED 9 CN361-B11 OP_LED 9
CN222- 8 PS10_SIG CN30- 1 PS10 CN311-B 2 OP_LED10 CN361-B12 OP_LED10
AC L
AC N
CN222- 9 5V sensor
F.GND
CN311-B 1 OP_LED11 CN361-B13 OP_LED11
Punch motor CN215- 8 M10 DRV1
CN215- 7 M10 DRV2
AC OUTLET
M10
CN25- 3
CN222-10 SGND CN25- 2
CN222-11 PS5_SIG Punch conveyance sensor
5
5
1
CN**-6 RTS CN16-6 /SYS_CTS
CN16-7 /PAPEROUT_1 CN78- 1 RED
CN223- 1 SD8_DRV CN78- 2 BLU
Roller
CN223- 2 SD24V_2 SD8
solenoid/4
CN221-A 1 SGND
5 CN601-1 Punch registration home sensor CN221-A 2 PS11_SIG CN374- 4
CN**-5 EXIT PS PS11 CN317- 1 TH_SIG CN374- 3
4 CN601-2 CN221-A 3 5V CN77- 1 RED Roller CN317- 2 GND
CN**-4 S.GND CN223- 3 SD7_DRV CN77- 2 BLU CN374- 2 TSB Temperature sensor board
3 CN601-3 CN223- 4 SD24V_2 SD7 CN317- 3 N.C CN374- 1
CN**-3 S.GND 2 CN601-4 solenoid/3 CN317- 4 5V
15 13
CN325- 3
CN306- 1 SGND CN325- 2
CN306- 2 PS35_SIG CN325- 1 PS35 L size sensor/Up
CN370- 6 5V CN79- 1 RED CN306- 3 5V
CN221-B 1 5V CN224- 1 SD9_DRV Sub tray gate
CN370- 5 LED1_SIG CN224- 2 SD24V_3 CN79- 2 BLU SD9
CN221-B 2 LED1_SIG
CN602-6
CN602-5
CN602-4
CN602-3
CN602-2
CN602-1
CN38- 3 CN306- 6 5V
CN370- 1 NC CN221-B 6 LED5_SIG CN224- 3 SGND CN38- 2 Main tray paper exit
6
6
CN334- 2
CN43- 3 CN306-11 PS44_SIG CN334- 1 PS44 PI paper set sensor/Up
CN224- 9 SGND CN43- 2 Main tray empty CN306-12 5V
CN224-10 PS23_SIG CN43- 1 PS23
CN224-11 5V
26
CN71- 1 sensor
CN71- 2
CN221-B 9 SD5_DRV
Roller solenoid/1 SD5 CN325- 3
RT11
CN33- 3 CN328- 3
F.GND
P.GND
P.GND
S.GND
CN21-3 /SYS_RTS CN17-3 /FNS1_CTS CN207- 1 24VDC CN210-A 4 SGND CN304-A11 SGND CN313- 7 SD13_DRV CN343-2/2
4 CN605-3 CN313- 8 SD_24V SD13 PI pick-up solenoid/Up
7
CN21-4 SYS_SOUT CN17-4 FNS1_SIN CN207- 2 PGND CN210-A 5 SGND CN304-A10 SGND
5 CN605-2
CN21-5 S.GND CN17-5 /FNSSET CN210-A 6 5V CN304-A 9 5VD
8
CN207- 6 PGND CN210-A10 NC CN304-A 5 NC CN307- 2 PS41_SIG CN331- 1 PS41 L size sensor/Lw
2 CN604-4 CN307- 3 5V
S.GND CN210-A11 SUBIN1 CN304-A 4 PANCH_S3 (Reserve)
3 CN604-3
S.GND CN210-A12 NC CN304-A 3 NC
7
7
4 CN604-2
16 20
CN304-B11 OP_LED 4
AC N
F.GND
AC L
AC INLET
CN326- 3
CN606- 2 CN15- 4 TIME_21 CN307-13 SGND CN326- 2
CN606- 6 CN15- 5 TIME_22 CN307-14 PS48_SIG CN326- 1 PS48 PI mac paper size sensor/Lw
16 17 18 19
CN307-15 5V
CN15- 6 TIME_23
FNS FDCB PDB
CN15- 7 NC
CN324- 3
CN307-16 SGND CN324- 2
CN307-17 PS46_SIG CN324- 1 PS46 Sub tray folding paper full sensor
CN307-18 5V
MAIN BODY
CN7-A12 KCIN_76 CN 6- 3 KCOUT_99 CN301-14 KCOUT_99 CN330- 1 PS40 PI lift plate home sensor/Lw
CN315- 6 5V
CN7-B 1 KCIN_77 CN 6- 4 KCOUT_100 CN301-13 KCOUT_100
CN7-B 2 KCIN_78 CN 6- 5 KCOUT_101 CN301-12 KCOUT_101
8
8
CN610- 6 CN344-1/1
CN314- 7 SD14_DRV CN344-2/2
CN314- 8 24V
FNS
CN302-A 7 KCIN_42
CN8-A12 KCOUT_124 CN4-A11 KCIN_43 CN302-A 6 KCIN_43
CN8-A13 KCOUT_125 CN4-A12 KCIN_44 CN302-A 5 KCIN_44
CN8-A14 KCOUT_126 CN4-A13 KCIN_45 CN302-A 4 KCIN_45 CN333- 3
CN8-A15 KCOUT_127 CN4-A14 KCIN_46 CN302-A 3 KCIN_46 CN314-13 SGND CN333- 2
CN8-A16 KCOUT_128 CN4-A15 KCIN_47 CN302-A 2 KCIN_47 CN314-14 PS43_SIG CN333- 1 PS43 PI cover open/close sensor
CN8-A17 NC CN4-A16 KCIN_48 CN314-15 5V
CN302-A 1 KCIN_48
CN8-B 1 KCOUT_129 CN4-B 1 KCIN_49 CN302-B16 KCIN_49
CN8-B 2 KCOUT_130 CN4-B 2 KCIN_50 CN302-B15 KCIN_50
CN8-B 3 KCOUT_131 CN4-B 3 KCIN_51 CN302-B14 KCIN_51 CN337-11
CN305- 1 24V CN337-10
CN8-B 4 KCOUT_132 CN4-B 4 KCIN_52 CN302-B13 KCIN_52 CN305- 2 24V CN337- 9
CN8-B 5 KCOUT_133 CN4-B 5 KCIN_53 CN302-B12 KCIN_53 CN305- 3 M7 PGND CN337- 8
CN8-B 6 KCOUT_134 CN4-B 6 KCIN_54 CN302-B11 KCIN_54 CN305- 4 M7 PGND CN337- 7
CN8-B 7 KCOUT_135 CN4-B 7 KCIN_55 CN302-B10 KCIN_55 CN305- 5 M7 H/L CN337- 6
CN305- 6 M7 LD CN337- 5 PI conveyance motor
M7
CN300- 1 24VDC
7
CN305-16 M9_DRV2
CN15-1 NC CN318-1 NC
CN15-2 NC CN318-2 NC
CN15-3 NC CN318-3 NC
CN15-4 NC CN318-4 NC
CN15-5 NC CN318-5 NC
CN15-6 NC CN318-6 NC
CN15-7 JYU_CLK1 CN318-7 JYU_CLK1
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
18.8 LS-501/502
1
1
Field Service Ver3.0 Nov.2006
Stacker tray
PS3
upper limit sensor
Paper press
solenoid/3 SD8
RLB/2
RLB/1
Front stopper
solenoid SD9
Entrance
2
2
PS4
sensor
Grip conveyance
PS5
home sensor
TOB
Paper empty
PS6
sensor
Paper detection
PS19
sensor
Conveyance
JAMIB
PS7
sensor/1
PS8
sensor
3
3
PS9
sensor
Job partition
SD2 solenoid
Sub tray exit
PS10
sensor
Rear stopper
SD3
LS-501 only
Conveyance solenoid
PS16
sensor/2
Front door lock
SD4 solenoid
JAM door
RS2
switch
Paper cooling fan
FM1 motor/Fr
PS8
sensor lock solenoid
Sub tray full Paper press
SD6 solenoid/1
PS9
sensor
LS-501 only
4
4
2nd gate
SD10
LS-502 only
PS10
sensor Paper press
SD7 solenoid/2
Hand cart reset Coupling
SD11 conveyance
RS1
switch
lock solenoid
LS-501 only
LED1
LED sensor
Toggle switch
SW1
PS1
sensor LS-501 only
Conveyance Paper cooling fan
LS-501 only
PS17
sensor/3 FM3 motor/Mi
PS11
5
5
up down motor
LS-502 only
2,000 sheets
LSCB
Conveyance
PS13
stacked sensor
M2
motor
5,000 sheets
PS14
stacked sensor
Sub tray exit
M3
release sensor
LS-501 only
sensor motor
6
6
M5
motor/1
Coupling
M6
conveyance motor
Paper cooling fan
FM6
motor/2
conveyance motor
FM4
motor
LS-501 only LS-502 only
Alignment motor
M7
MAIN BODY
I/F
7
7
MAIN BODY
I/F
Stacker tray
MS2
CONVE-
LS-501 only
Main
YANCE Body/LS
I/F
CONVE-
YANCE
I/F
LS-501 only
LS/FS
8
8
LS-501 only
MAIN BODY
I/F
Inlet
Crimp
AC
Symbol
DCPS
LS-501 only
CONVEYANCE
AC
Connector
Outlet
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
18.9 FS-503
1
1
Field Service Ver3.0 Nov.2006
2
2
3
3
4
4
sensor/Fr PS31 CN125-1 CN216-6 CN216-1 CN200-B12 CN200-B1 CN58-B15 PS31_5V CN54- 4 PS 7_S.GND CN212-3 CN212-4 CN144-3
CN54- 5 PS 7_SIG CN212-2 CN212-5 CN144-2
Staple exit upper
CN54- 6 PS 7_5V CN212-1 CN212-6 CN144-1
PS7 limit sensor
5
5
CN20-2 5V CN751-A
3
release solenoid SD7 CN140-2 -1 CN201-2 CN201-7 CN65-1 STP_HP_SIG CN10- 3 CN20-4 S.GND CN751-B
CN56-A 2 SD7_DRV
CN65-2 PS8_SIG CN10- 2
CN65-3 PS31_SIG CN10- 1
CN142-3 CN201-3 CN201-6 CN56-A 3 M13_24V CN19-1 NC
CN142-9 CN201-4 CN201-5 CN56-A 4 M13_24V CN66-1 M13_VREF CN19-2 NC
CN142-1 CN201-5 CN201-4 CN56-A 5 M13_DRV_A CN66-2 NC CN19-3 FNS2_SIN CN757-2 SIN
Stacker entrance motor M13 CN142-5 CN201-6 CN201-3 CN56-A 6 M13_DRV_A/ CN19-4 FNS2_RTS CN757-1 RTS
CN142-7 CN201-7 CN201-2 CN56-A 7 M13_DRV_B CN62- 1 M8_A CN3-16
CN142-11 CN201-8 CN201-1 CN56-A 8 M13_DRV_B/ CN62- 2 M8_A/ CN3-15
CN56-A 9 NC CN62- 3 M8_B CN3-14
CN56-A10 NC CN62- 4 M8_B/ CN3-13 CN16-1 SYS_SIN CN756-1 MTXD
CN56-A11 NC CN62- 5 M24_A CN3-12 CN16-2 S.GND CN756-2 S.GND
CN143-11 CN56-B 1 M23_24V CN62- 6 M24_A/ CN3-11 CN16-3 SYS_RTS CN756-3 MCTS
CN143-10 CN56-B 2 M23_24V CN62- 7 M24_B CN3-10 CN16-4 SYS_SOUT CN756-4 MRXD
CN143-9 CN56-B 3 M23_P.GND CN62- 8 M24_B/ CN3- 9 CN16-5 S.GND CN756-5 S.GND
CN143-8 CN56-B 4 M23_P.GND CN62- 9 M26_A CN3- 8 CN16-6 SYS_CTS CN756-6 MRTS
CN143-7 CN56-B 5 M23_H/L CN62-10 M26_A/ CN3- 7
Paper exit arm motor M23 CN143-6 CN56-B 6 M23_LD_SIG CN62-11 M26_B CN3- 6 CN16-7 PAPEROUT_1 CN752-1
7
7
CN750-A CN752-4 5V
CN64- 1 NC CN14-18
1
CN63-B16 M23_LD_SIG
CN63-B15 M3_LD_SIG
CN63-B14 M7_LD_SIG
CN63-B13 M1_LD_SIG
CN63-B12 F_READY_SIG
CN63-B11 F_CD_SIG
CN63-B10 F_LS_SIG
CN63-B 9 F_HP_SIG
CN63-B 8 R_READY_SIG
CN63-B 7 R_CD_SIG
CN63-B 6 R_LS_SIG
CN63-B 5 R_HP_SIG
CN63-B 4 NC
CN63-B 3 PS20_SIG
CN63-B 2 PS9_SIG
CN63-B 1 24VDEC
CN63-A16 PS35_SIG
CN63-A15 PS33_SIG
CN63-A14 PS32_SIG
CN63-A13 PS14_SIG
CN63-A12 PS11_SIG
CN63-A11 PS34_SIG
CN63-A10 PS30_SIG
CN63-A 9 PS1_SIG
CN63-A 8 PS5_SIG
CN63-A 7 PS4_SIG
CN63-A 6 PS15_SIG
CN63-A 5 PS12_SIG
CN63-A 4 PS10_SIG
CN63-A 3 PS3_SIG
CN63-A 2 PS7_SIG
CN63-A 1 PS2_SIG
CN61-B20 M5_VREF
CN61-B19 M5_EN
CN61-B18 M5_F/R
CN61-B17 M22_VREF
CN61-B16 M22_EN
CN61-B15 M22_F/R
CN61-B14 LED6
CN61-B13 M13_EN
CN61-B12 LED7
CN61-B11 M2_B/
CN61-B10 M2_B
CN61-B 9 M2_A/
CN61-B 8 M2_A
CN61-B 7 LED8
CN61-B 6 M23_CONT
CN61-B 5 M23_F/R
CN61-B 4 M23_H/L
CN61-B 3 M25_CONT
CN61-B 2 SD7_CONT
CN61-B 1 M4_CONT
CN61-A20 STA_F_F/R
CN61-A19 STA_F_CONT
CN61-A18 STA_R_F/R
CN61-A17 STA_R_CONT
CN61-A16 SD9_CONT
CN61-A15 M6_B/
CN61-A14 SD5_CONT
CN61-A13 SD2_CONT
CN61-A12 M6_B
CN61-A11 M6_A/
CN61-A10 M6_A
CN61-A 9 M3_CONT
CN61-A 8 M3_F/R
CN61-A 7 LED5
CN61-A 6 M7_CONT
CN61-A 5 M7_F/R
CN61-A 4 M7_H/L
CN61-A 3 M1_CONT
CN61-A 2 M1_F/R
CN61-A 1 M1_H/L
FNSCB
Crimp
Symbol
CN 1-B 1
CN 1-B 2
CN 1-B 3
CN 1-B 4
CN 1-B 5
CN 1-B 6
CN 1-B 7
CN 1-B 8
CN 1-B 9
CN 1-A 1
CN 1-A 2
CN 1-A 3
CN 1-A 4
CN 1-A 5
CN 1-A 6
CN 1-A 7
CN 1-A 8
CN 1-A 9
CN 2-B 1
CN 2-B 2
CN 2-B 3
CN 2-B 4
CN 2-B 5
CN 2-B 6
CN 2-B 7
CN 2-B 8
CN 2-B 9
CN 2-A 1
CN 2-A 2
CN 2-A 3
CN 2-A 4
CN 2-A 5
CN 2-A 6
CN 2-A 7
CN 2-A 8
CN 2-A 9
CN 1-B10
CN 1-B11
CN 1-B12
CN 1-B13
CN 1-B14
CN 1-B15
CN 1-B16
CN 1-A10
CN 1-A11
CN 1-A12
CN 1-A13
CN 1-A14
CN 1-A15
CN 1-A16
CN 2-B10
CN 2-B11
CN 2-B12
CN 2-B13
CN 2-B14
CN 2-B15
CN 2-B16
CN 2-B17
CN 2-B18
CN 2-B19
CN 2-B20
CN 2-A10
CN 2-A11
CN 2-A12
CN 2-A13
CN 2-A14
CN 2-A15
CN 2-A16
CN 2-A17
CN 2-A18
CN 2-A19
CN 2-A20
Connector
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
J1-7 J1-1 CN228- 2
CN120-A16 PS1_SIG CN140-A 1 24V CN228- 1 24V
J1-6 J1-2 CN228- 1 SD1 Entrance gate solenoid
CN120-A15 PS2_SIG CN140-A 2 SD1_DRV CN228- 2 DRV
CN120-A14 PS3_SIG
CN120-A13 PS4_SIG J1-5 J1-3 CN229- 2
CN140-A 3 24V CN229- 1 24V
CN120-A12 PS5_SIG J1-4 J1-4 CN229- 1 SD2 Right angle conveyance gate solenoid
CN140-A 4 SD2_DRV CN229- 2 DRV
CN120-A11 PS6_SIG
CN120-A10 PS7_SIG J1-3 J1-5
CN140-A 5 SG CN236- 3 S.GND
CN120-A 9 PS8_SIG J1-2 J1-6
CN140-A 6 PS1_SIG CN236- 2 SIG PS1 Entrance sensor
CN120-A 8 PS17_SIG J1-1 J1-7
18.10 SD-501 1/4
CN140-A 7 5V CN236- 1 5V
CN120-A 7 PS18_SIG J9-3 J9-1
CN120-A 6 PS49_SIG CN140-A 8 SG CN240- 3 S.GND
J9-2 J9-2
CN120-A 5 PS20_SIG CN140-A 9 PS5_SIG CN240- 2 SIG PS5 Right angle conveyance sensor/1
1
1
J9-1 J9-3
CN120-A 4 PS21_SIG CN140-A10 5V CN240- 1 5V
CN120-A 3 PS22_SIG J6-9 J6-1
CN140-A11 SG CN252- 3 S.GND
CN120-A 2 PS23_SIG J6-8 J6-2
CN140-A12 PS17_SIG CN252- 2 SIG PS17 Overlap home sensor
CN120-A 1 PS24_SIG J6-7 J6-3
CN140-A13 5V CN252- 1 5V
CN120-B16 PS9_SIG
J6-6 J6-4 CN212- 6
Field Service Ver3.0 Nov.2006
2
2
3
3
CN121-B 8 M6_ENA
CN121-B 7 M6_F/R J8-5 J8-1
CN141- 7 SG CN244- 3 S.GND
CN121-B 6 M6_CONT1 J8-4 J8-2
CN141- 8 PS 9_SIG CN244- 2 SIG PS9 Tri-folding exit sensor
CN121-B 5 M6_CONT2 J8-3 J8-3
CN141- 9 5V CN244- 1 5V
CN121-B 4 M5_S/S
CN121-B 3 M5_F/R J8-2 J8-4 CN280- 2
CN141- 10 24V CN280- 1 24V
CN121-B 2 M5_H/L J8-1 J8-5 CN280- 1 CL1 Tri-folding exit cluch
CN141- 11 MC 1_DRV CN280- 2 DRV
CN121-B 1 MC1_CONT
4
CN238- 3 S.GND
4
SDDB 1/2
CN122-B11 LED6
CN231- 2
CN122-B10 LED7 CN144-B 3 24V CN231- 1 24V
CN231- 1 SD4 Roller release solenoid/4
CN122-B 9 LED8 CN144-B 4 SD4_DRV CN231- 2 DRV
CN122-B 8 SD8_CONT1
CN122-B 7 SD8_CONT2 CN144-B 5 24V CN201-11 24V
CN122-B 6 TRI/M3_CONT CN144-B 6 24V CN201-10 24V
Horizontal conveyance
29
CN125-A 9 PS28_SIG
5
5
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
J29-12 J29- 1 CN214- 6
CN154- 1 24V CN214- 1 COM
J29-11 J29- 2 CN214- 5
CN154- 2 24V CN214- 2 COM
J29-10 J29- 3 CN214- 4
CN154- 3 M15_DRV_A CN214- 3 A
J29- 9 J29- 4 CN214- 3 M15 Stapler movement motor
CN154- 4 M15_DRV_A/ CN214- 4 A/
J29- 8 J29- 5 CN214- 2
CN154- 5 M15_DRV_B CN214- 5 B
J29- 7 J29- 6 CN214- 1
CN154- 6 M15_DRV_B/ CN214- 6 B/
18.11 SD-501 2/4
10
10
J30- 4 J30- 5
CN155- 5 M21_DRV_1 CN220- 2 DRV2
J30- 3 J30- 6 M21 Saddle stitching press motor
CN155- 6 M21_DRV_2 CN220- 1 DRV1
J30- 2 J30- 7
CN155- 7 M26_DRV_1 CN225- 1 DRV1 Bundle arm assist motor
J30- 1 J30- 8 M26
CN170- 1 5V CN155- 8 M26_DRV_2 CN225- 2 DRV2
CN170- 2 LED1
CN170- 3 LED2
CN170- 4 LED3 J28-A18 J28-A 1 J44- 3 J44- 1
CN153-A 1 SG CN262- 3 S.GND
CN170- 5 LED4 J28-A17 J28-A 2 J44- 2 J44- 2
CN153-A 2 PS27_SIG CN262- 2 SIG PS27 Saddle stitching press home sensor
CN170- 6 NC J28-A16 J28-A 3 J44- 1 J44- 3
CN153-A 3 5V
30
CN170- 7 5V CN262- 1 5V
CN170- 8 LED5
CN170- 9 LED6 J28-A15 J28-A 4
CN153-A 4 SG CN264- 3 S.GND
CN170-10 LED7 J28-A14 J28-A 5
CN153-A 5 PS29_SIG CN264- 2 SIG PS29 Saddle stitching alignment home sensor/Lt
CN170-11 LED8 J28-A13 J28-A 6
CN153-A 6 5V CN264- 1 5V
CN170-12 NC
11
J28-A12 J28-A 7
11
J28-B15 J28-B 4 J 7- 3 J 7- 1
CN153-B 4 SG CN260- 3 S.GND
J28-B14 J28-B 5 J 7- 2 J 7- 2
CN153-B 5 PS25_SIG CN260- 2 SIG PS25 Stapler movement home sensor
J28-B13 J28-B 6 J 7- 1 J 7- 3
CN153-B 6 5V CN260- 1 5V
12
12
SDDB 2/2
Saddle stitching
CN100-1 5V
J28-B 9 J28-B10 J31- 9 J31- 1
CN100-2 5V CN153-B10 SG CN249- 3 S.GND
J28-B 8 J28-B11 J31- 8 J31- 2
CN100-3 S.GND CN153-B11 PS14_SIG CN249- 2 SIG PS14 Bundle sensor
J28-B 7 J28-B12 J31- 7 J31- 3
CN100-4 S.GND CN153-B12 5V CN249- 1 5V
J28-B 6 J28-B13 J31- 6 J31- 4
CN153-B13 SG CN265- 3 S.GND
J28-B 5 J28-B14 J31- 5 J31- 5
CN153-B14 PS30_SIG CN265- 2 SIG PS30 Bundle clip lower limit sensor
J28-B 4 J28-B15 J31- 4 J31- 6
CN153-B15 5V CN265- 1 5V
J28-B 3 J28-B16 J31- 3 J31- 7
CN153-B16 SG CN268- 3 S.GND
J28-B 2 J28-B17 J31- 2 J31- 8
CN153-B17 PS33_SIG CN268- 2 SIG PS33 Bundle clip upper limit sensor
J28-B 1 J28-B18 J31- 1 J31- 9
CN153-B18 5V CN268- 1 5V
13
13
CN208- 4 NC
J26- 5 J26- 9
31
CN156-B 3 M 9_DRV_A CN208- 1 A
CN208- 6 NC M9 Saddle stitching alignment motor/Rt
CN162-1 24V J26- 4 J26- 10
CN156-B 4 M 9_DRV_A/ CN208- 5 A/
CN162-2 24V CN208- 8 NC
J26- 3 J26- 11
CN156-B 5 M 9_DRV_B CN208- 7 B
CN162-3 24V CN208-10 NC
J26- 2 J26- 13
CN156-B 6 M 9_DRV_B/ CN208-11 B/
CN162-4 P.GND CN156-B 7 NC
J26- 1 J26- 13
CN162-5 P.GND
CN162-6 P.GND
J35- 1 J35- 1
CN150- 1 M23_DRV_1 CN222- 1 DRV1 Bundle press motor
CN163-1 24V J35- 2 J35- 2 M23
CN150- 2 M23_DRV_2 CN222- 2 DRV2
CN163-2 24V
CN163-3 24V
CN163-6 P.GND
J37- 9 J37- 1
CN151-A 1 SG CN250- 3 S.GND
14
14
J37- 8 J37- 2
CN151-A 2 PS15_SIG CN250- 2 SIG PS15 Bundle sensor/2
J37- 7 J37- 3
CN151-A 3 5V CN250- 1 5V
J37- 6 J37- 4
CN151-A 4 SG CN269- 3 S.GND
J37- 5 J37- 5
CN151-A 5 PS34_SIG CN269- 2 SIG PS34 Bundle registration home sensor
J37- 4 J37- 6
CN151-A 6 5V CN269- 1 5V
J37- 3 J37- 7
CN151-A 7 SG CN290- 3 S.GND
J37- 2 J37- 8
CN151-A 8 PS54_SIG CN290- 2 SIG PS54 Bundle sensor/4
J37- 1 J37- 9
CN151-A 9 5V CN290- 1 5V
J34- 12 J34- 1
CN151-B 1 SG CN271- 3 S.GND
J34- 11 J34- 2
CN167-1 TRI/M3_DRV1 CN151-B 2 PS36_SIG CN271- 2 SIG PS36 Bundle press movement home sensor
J34- 10 J34- 3
15
15
CN151-B20 NC
J43- 3 J43- 1
CN149-A 1 SG CN239- 3 S.GND
J43- 2 J43- 2
CN149-A 2 PS 4_SIG CN239- 2 SIG PS4 Horizontal conveyance exit sensor
J43- 1 J43- 3
CN149-A 3 5V CN239- 1 5V
CN164-1 STA/R_DRV1
16
16
CN164-2 STA/R_DRV2
CN164-3 STA/L_DRV1
CN149-A 4 SG CN266- 3 S.GND
CN164-4 STA/L_DRV2
CN149-A 5 PS31_SIG CN266- 2 SIG Bundle arm rotation home sensor
CN164-5 CLI/R_DRV1 PS31
CN149-A 6 5V CN266- 1 5V
CN164-6 CLI/R_DRV2
CN164-7 CLI/L_DRV1 CN149-A 7 SG CN270- 3 S.GND
Bundle
CN164-8 CLI/L_DRV2 CN149-A 8 PS35_SIG CN270- 2 SIG PS35 Bundle press stage up down home motor
CN149-A 9 5V CN270- 1 5V
CN149-A10 SG CN275- 3 S.GND
CN149-A11 PS40_SIG CN275- 2 SIG PS40 Scraps box set sensor
CN149-A12 5V CN275- 1 5V
CN149-A13 SG CN284- 3 S.GND
CN165- 1 5V
CN149-B 5 PS48_SIG CN284- 2 SIG Scraps press home sensor
CN165- 2 5V PS48
CN149-A15 5V CN284- 1 5V
CN165- 3 SG
CN165- 4 SG CN149-B 1 SG CN281- 3 S.GND
CN165- 5 STA/R_LOW CN149-B 2 PS45_SIG CN281- 2 SIG PS45 Bundle press stage up down limit sensor
CN165- 6 STA/R_HP_IN CN149-B 3 5V CN281- 1 5V
CN165- 7 CLI/R_TIM
CN165- 8 5V J45- 6 J45- 1
CN149-B 4 SG CN297- 3 S.GND
CN165- 9 5V J45- 5 J45- 2
CN149-B 5 PS61_SIG CN297- 2 SIG Bundle tray paper full sensor
CN165-10 SG J45- 4 J45- 3 PS61
CN149-B 6 5V CN297- 1 5V
CN165-11 SG
J45- 3 J45- 4
CN165-12 STA/L_LOW CN149-B 7 SG CN293- 3 S.GND
J45- 2 J45- 5
CN165-13 STA/L_HP_IN CN149-B 8 PS57_SIG CN293- 2 SIG Bundle exit sensor/2
J45- 1 J45- 6 PS57
CN165-14 CLI/L_TIM CN149-B 9 5V CN293- 1 5V
17
17
J36- 6 J36- 1
CN149-B10 SG CN294- 3 S.GND
J36- 5 J36- 2
CN149-B11 PS58_SIG CN294- 2 SIG PS58 Bundle tray set sensor
J36- 4 J36- 3
CN149-B12 5V CN294- 1 5V
J36- 3 J36- 4
CN149-B13 SG CN276- 3 S.GND
J36- 2 J36- 5
CN151-B17 PS41_SIG CN276- 2 SIG PS41 Trimmer scraps full sensor
J36- 1 J36- 6
CN149-B15 5V CN276- 1 5V
H
D
C
G
18. OVERALL WIRING DIAGRAM
P
K
R
N
Q
O
M
CN9-A 1 5V CN1-A 1 KCIN_1
CN9-A 2 5V CN1-A 2 KCIN_2
CN9-A 3 NSW1-1 CN1-A 3 KCIN_3
CN9-A 4 NSW1-2 CN1-A 4 KCIN_4
CN9-A 5 NSW1-4 CN1-A 5 KCIN_5
CN9-A 6 NSW1-8 CN1-A 6 KCIN_6
CN9-A 7 NSW2-1 CN1-A 7 KCIN_7
CN9-A 8 NSW2-2 CN1-A 8 KCIN_8
CN9-A 9 NSW2-4 CN1-A 9 KCIN_9
18.12 SD-501 3/4
1
1
CN1-B 2 KCIN_18
CN9-A19 NSW5-1 CN1-B 3 KCIN_19
CN9-A20 NSW5-2 CN1-B 4 KCIN_20
CN9-B 1 NSW5-4 CN1-B 5 KCIN_21
CN9-B 2 NSW6 CN1-B 6 KCIN_22
CN9-B 3 NSW8 CN1-B 7 KCIN_23
CN9-B 4 NSW7 CN1-B 8 KCIN_24
CN9-B 5 NLED0 CN1-B 9 KCIN_25
CN9-B 6 NLED1 CN1-B10 KCIN_26
CN9-B 7 NLED2 CN1-B11 KCIN_27
CN9-B 8 NLED3 CN1-B12 KCIN_28
CN9-B 9 NLED4 CN1-B13 KCIN_29
CN9-B10 NLED5 CN1-B14 KCIN_30
CN9-B11 NLED6 CN1-B15 KCIN_31
CN9-B12 NLED7 CN1-B16 KCIN_32
CN9-B13 NC
CN9-B14 NC
CN2-A 1 KCOUT_1
CN9-B15 NC
CN2-A 2 KCOUT_2
CN9-B16 NC
CN2-A 3 KCOUT_3
CN9-B17 NC
CN2-A 4 KCOUT_4
CN9-B18 NC
CN2-A 5 KCOUT_5
CN9-B19 NC
2
2
CN2-A 6 KCOUT_6
CN9-B20 NC
CN2-A 7 KCOUT_7
CN2-A 8 KCOUT_8
CN2-A 9 KCOUT_9
CN111-1 CN2-A10 KCOUT_10
CN19-4 FNS2_RTS CN2-A11 KCOUT_11
CN111-2
CN19-3 FNS2_SIN CN2-A12 KCOUT_12
CN19-2 NC(SYS_RTS) CN2-A13 KCOUT_13
CN19-1 NC(SYS_SIN) CN2-A14 KCOUT_14
CN2-A15 KCOUT_15
CN104-1 MTXD CN2-A16 KCOUT_16
CN16-1 SYS_SIN CN2-A17 KCOUT_17
CN104-2 SG
CN16-2 S.GND CN2-A18 KCOUT_18
CN104-3 MCTS
CN16-3 /SYS_RTS CN2-A19 KCOUT_19
CN104-4 MRXD
CN16-4 SYS_SOUT CN2-A20 KCOUT_20
CN104-5 SG
CN16-5 S.GND CN2-B 1 KCOUT_21
CN104-6 MRTS
CN16-6 /SYS_CTS CN2-B 2 KCOUT_22
CN16-7 /PAPEROUT_1 CN2-B 3 KCOUT_23
CN107-1 PAPER_OUT CN2-B 4 KCOUT_24
CN107-2 SG CN2-B 5 KCOUT_25
6
CN20-1 5V CN2-B 6 KCOUT_26
CN107-3 SG
5
CN20-2 5V CN2-B 7 KCOUT_27
CN107-4 5V 9
4
CN20-3 S.GND CN2-B 8 KCOUT_28
CN107-5 5V
3
10
3
3
CN103-2 5V
1
CN103-3 SG CN2-B13 KCOUT_33
2
CN103-4 PG CN2-B14 KCOUT_34
CN103-5 PG CN2-B15 KCOUT_35
CN103-6 FG CN2-B16 KCOUT_36
CN2-B17 KCOUT_37
CN2-B18 KCOUT_38
CN2-B19 KCOUT_39
CN2-B20 KCOUT_40
CN6- 1 KCOUT_97
CN192-2
7
CN6- 2 KCOUT_98
CN192-3 CN6- 3 KCOUT_99
1
11
5V
CN6- 5 KCOUT_101
CN6- 6 KCOUT_102
CN192-6 CN6- 7 KCOUT_103
9
CN6- 9 KCOUT_105
SG
CN192-5 CN192-8
CN6-10 KCOUT_106
16
CN6-11 KCOUT_107
CN6-12 KCOUT_108
CN6-16 KCOUT_112
CN190-5
4
4
5V
17
CN190-6
3
18
CN105-4 MCTS
CN17-3 MCTS CN4-A 7 KCIN_39
CN105-3 MRXD
29
5
5
CN105-2 SG
CN17-5 SG CN4-A 9 KCIN_41
CN105-1 MRTS
CN17-6 MRTS CN4-A10 KCIN_42
CN17-7 /PAPEROUT_2 CN4-A11 KCIN_43
CN17-8 NC CN4-A12 KCIN_44
CN108-5 PAPER_OUT
CN4-A13 KCIN_45
CN108-4 SG
CN4-A14 KCIN_46
20
CN108-3 SG
CN4-A15 KCIN_47
19
CN108-2 5V
CN4-A16 KCIN_48
18
CN108-1 5V
CN4-B 1 KCIN_49
17
CN4-B 2 KCIN_50
CN4-B 3 KCIN_51
CN4-B 4 KCIN_52
CN4-B 5 KCIN_53
CN4-B 6 KCIN_54
CN4-B 7 KCIN_55
CN106-1 24V CN106-1 24V CN4-B 8 KCIN_56
CN106-2 5V CN106-2 5V CN4-B 9 KCIN_57
15
CN5-A 1 KCOUT_57
6
6
CN5-A 2 KCOUT_58
To rear option
CN5-A 3 KCOUT_59
CN5-A 4 KCOUT_60
CN5-A 5 KCOUT_61
CN5-A 6 KCOUT_62
CN12-1 NC CN5-A 7 KCOUT_63
CN12-2 M33_CLK CN5-A 8 KCOUT_64
CN12-3 NC CN5-A 9 KCOUT_65
CN12-4 NC CN5-A10 KCOUT_66
J48-1 J48-4 M33_CLK
CN12-5 NC CN5-A11 KCOUT_67
J48-2 J48-3 M33_CONT
CN12-6 M33_CONT CN5-A12 KCOUT_68
J48-3 J48-2 M33_LD
CN12-7 M33_LD CN5-A13 KCOUT_69
J48-4 J48-1 M33_FR
CN12-8 M33_FR CN5-A14 KCOUT_70
CN5-A15 KCOUT_71
CN5-A16 KCOUT_72
CN5-A17 KCOUT_73
CN5-A18 KCOUT_74
CN5-A19 KCOUT_75
CN5-A20 KCOUT_76
CN5-B 1 KCOUT_77
CN363- 6 LD
CN5-B 2 KCOUT_78
CN363- 1 NC
CN363- 7 H/L
CN363-10 24V
CN363-11 24V
CN5-B 3 KCOUT_79
CN363- 2 S.GND
CN363- 8 P.GND
CN363- 9 P.GND
CN363- 4 CLOCK
CN5-B 4 KCOUT_80
CN363- 5 CW/CCW
CN5-B 5 KCOUT_81
CN363- 3 START/STOP
CN5-B 6 KCOUT_82
CN5-B 7 KCOUT_83
CN5-B 8 KCOUT_84
7
7
M33
CN5-B 9 KCOUT_85
CN5-B10 KCOUT_86
CN5-B11 KCOUT_87
CN5-B12 KCOUT_88
CN5-B13 KCOUT_89
AC CODE
CN5-B14 KCOUT_90
CN5-B15 KCOUT_91
CN5-B16 KCOUT_92
CN5-B17 KCOUT_93
CN5-B18 KCOUT_94
CN5-B19 KCOUT_95
CN5-B20 KCOUT_96
Trimmer paddle motor
AC INRET
CN7-A 1 KCIN_65
CN7-A 2 KCIN_66
FT2
FT1
CN7-A 3 KCIN_67
CN7-A 4 KCIN_68
CN7-A 5 KCIN_69
CN7-A 6 KCIN_70
WIT
BLK
CN7-A 7 KCIN_71
CN7-A 8 KCIN_72
FT4
FT3
CN7-A 9 KCIN_73
CN7-A10 KCIN_74
8
8
CN7-A11 KCIN_75
CN7-A12 KCIN_76
CN7-B 1 KCIN_77
CBR2
CBR1
CN7-B 2 KCIN_78
FT6
FT5
CN7-B 3 KCIN_79
Circuit breaker/2
Circuit breaker/1
CN7-B 4 KCIN_80
CN7-B 5 KCIN_81
CN7-B 6 KCIN_82
CN7-B 7 KCIN_83
CN7-B 8 KCIN_84
WIT FT8
BLK FT7
CN7-B 9 KCIN_85
4
3
CN7-B10 KCIN_86
CN7-B11 KCIN_87
NF
CN7-B12 KCIN_88
2
1
FT9
CN10- 1 IRQ_4
FT10
CN10- 2 /IRQ_3
CN10- 3 /IRQ_1
BLK
WIT
CN14- 1 TIME_0
NOISE FILTER
CN14- 2 TIME_1
FT11
CN14- 3 TIME_2
FT14 CN14- 4 TIME_3
CN24-1 RL1_CONT
CN14- 5 TIME_4
CN14- 6 TIME_5
RL1
Power relay
CN14- 9 TIME_8
FT12
CN14-10 TIME_9
CN14-11 TIME_10
CN14-12 TIME_11
BLK
CN14-13 TIME_12
CN14-14 TIME_13
CN14-15 TIME_14
34
33
CN14-16 TIME_15
CN14-17 TIME_16
CN14-18 TIME_17
J
P
K
R
N
Q
O
M
18. OVERALL WIRING DIAGRAM
P
K
R
N
Q
O
M
34
33
18.13 SD-501 4/4
10
10
CN195-2
CN195-1
Field Service Ver3.0 Nov.2006
CN370- 6 5V J46-1 -6
CN370- 5 LED1 -2 -5
-3 -4
WIT
BLK
CN370- 4 LED2
CN370- 3 LED3 -4 -3
CN188-2A
CN188-1A
CN370- 2 LED4 -5 -2
CN370- 1 NC -6 -1
MS1
Front door switch/Rt
JAMIB/1
CN188-2B
CN188-1B
ACSW
WIT
BLK
CN189-2A
CN189-1A
MS2
30
CN189-2B
CN189-1B
11
11
CN195-4
CN195-3
CN370- 6 5V
CN370- 5 LED1
CN370- 4 LED2
WIT
BLK
CN370- 3 LED3
CN370- 2 LED4
CN370- 1 NC
G/Y
G/Y
G/Y
WIT
WIT
WIT
BLK
BLK
BLK
JAMIB/2
CN185-3
CN185-1
CN185-5
CN184-3
CN184-1
CN184-5
CN183-3
CN183-1
CN183-5
: Line (H)
: Line (H)
: Line (H)
: Neutral (N)
: Neutral (N)
: Neutral (N)
: Frame GND
: Frame GND
: Frame GND
12
12
11
:-V/PGND
CN182-1
:-V/PGND
CN182-2
:-V/PGND
CN182-3
:-V/PGND
CN182-4
:+V/24V
CN182-5
:+V/24V
CN182-6
:+V/24V
CN182-7
:+V/24V
CN182-8
:-V/PGND
CN181-1
:-V/PGND
CN181-2
:-V/PGND
CN181-3
:-V/PGND
CN181-4
:+V/24V
CN181-5
:+V/24V
CN181-6
:+V/24V
CN181-7
:+V/24V
CN181-8
:-V/PGND
CN180-1
:-V/PGND
CN180-2
:-V/PGND
CN180-3
:-V/PGND
CN180-4
:+V/24V
CN180-5
:+V/24V
CN180-6
:+V/24V
CN180-7
:+V/24V
CN180-8
13
13
31
14
14
CN2??- 1 24V
Trimmer press motor M32 CN2??- 2 DRV
CN2??- 1 24V
15
15
CN2??- 3 S.GND
Trimmer blade home sensor PS50 CN2??- 2 SIG
CN2??- 1 5V
CN2??- 3 S.GND
Trimmer blade upper limit sensor PS51 CN2??- 2 SIG
CN2??- 1 5V
CN2??- 3 S.GND
Trimmer press upper limit sensor PS52 CN2??- 2 SIG
CN2??- 1 5V
CN2??- 3 S.GND
Trimmer press home sensor PS53 CN2??- 2 SIG
CN2??- 1 5V
Trimmer unit
CN2??- 3 S.GND
Trimmer board replacement sensor PS59 CN2??- 2 SIG
CN2??- 1 5V
32
J33- 1 J33- 1
25
-2 -2
16
16
-3 -3
26
-4 -4
CN352-1 CLI_SD_DRV -5 -5
Clincher solenoid/Rt SD9 -6 -6
CN352-2 CLI_SD_GND
-7 -7
-8 -8
-9 -9
23
21
CN350- 4 NC
CN350- 6 NC
CN350- 8 5V J32- 1 J32-14
CN350- 9 5V -2 -13
Stapler motor/Rt CN350-10 S.GND -3 -12
M29 -4 -11
CN350-12 S.GND
CN350- 1 STA_LOW -5 -10
CN350- 3 STA_HP -6 -9
CN350- 7 CLINCH -7 -8
CN350- 5 MOTOR_24V -8 -7
CN350-11 MOTOR_DRV -9 -6
-5
-10 -4
27
-11 -3
-12 -2
28
-13 -1
CN353-1 CLI_SD_DRV -14
Clincher solenoid/Lt SD10
17
17
CN353-2 CLI_SD_GND
24
CN351- 5 MOTOR_24V
CN351-11 MOTOR_DRV
CN351- 2 NC
CN351- 4 NC
CN351- 6 NC
Stapler motor/Lt M30 CN351- 8 5V
CN351- 9 5V
Crimp
Symbol
CN351-10 S.GND
CN351-12 S.GND
CN351- 1 STA_LOW
CN351- 3 STA_HP
Stapler/Clincher
CN351- 7 CLINCH
21
23
Connector
25
26
22
18
18
24
27
28
Relay connector
Faston
J
P
K
R
N
Q
O
M
18. OVERALL WIRING DIAGRAM
H
D
C
G
CN54-A 1 M15_MODE1 CN70- 1 M1_24V CN100- 2 COM
CN54-A 2 M15_CLK CN70- 2 M1_24V CN100- 5 COM
CN54-A 3 M12_CONT2 CN70- 3 M1_DRV_A CN100- 1 A
18.14 PB-501 1/4
1
1
5
CN54-A 8 M12_CLK CN70- 8 M31_24V
6
CN54-A 9 M11_CONT2 CN70- 9 M31_DRV_A
7
CN54-A10 M11_CONT1 CN70- 10 M31_DRV_A/ (Glue tank movement motor M31)
8
CN54-A11 M11_F/R CN70- 11 M31_DRV_B
9
CN54-A12 M11_EN CN70- 12 M31_DRV_B/
Field Service Ver3.0 Nov.2006
CN54-A13 M11_MODE1
CN54-A14 M11_CLK
CN54-A15 M1_CONT2 CN80-A 1 M2_24V CN101-11 24V
CN54-A16 M1_CONT1 CN80-A 2 M2_24V CN101-10 24V
CN54-A17 M1_F/R CN80-A 3 M2_PGND CN101- 9 P.GND
CN54-A18 M1_EN CN80-A 4 M2_PGND CN101- 8 P.GND
CN54-A19 M1_MODE1 CN80-A 5 M2_H/L CN101- 7 H/L
CN54-A20 M1_CLK
Intermediate conveyance
CN80-A 6 M2_LD CN101- 6 LD M2
CN54-B 1 M4_CONT CN80-A 7 M2_F/R CN101- 5 CW/CCW
motor
CN54-B 2 SD61_F/R CN80-A 8 M2_CLK CN101- 4 CLOCK
CN54-B 3 SD61_CONT CN80-A 9 M2_CONT CN101- 3 START/STOP
CN54-B 4 SD91_CONT CN80-A10 M2_SGND CN101- 2 S.GND
CN54-B 5 M21_CONT2 CN80-A11 M2_5V CN101- 1 5V
CN54-B 6 M21_CONT1
CN54-B 7 M21_F/R J16-6 -1 -2
CN80-A12 SD2_24V CN141- 1 24V
CN54-B 8 M21_EN J16-7 -2 -1 SD2 Bypass gate solenoid
CN80-A13 SD2_DRV CN141- 2 DRV
CN54-B 9 M21_MODE1
CN54-B10 M21_CLK
CN54-B11 M17_CONT2 J10-20 -1 -2
CN80-B 1 SD1_24V CN140- 1 24V
CN54-B12 M17_CONT1 J10-19 -2 -1 SD1 Entrance gate solenoid
CN80-B 2 SD1_DRV CN140- 2 DRV
CN54-B13 M17_F/R
2
2
51
CN55-A 6 M42_MODE1 CN80-B12 M81_LD CN138- 4 PGND
52
CN55-A 7 M42_CLK CN80-B13 M81_H/L
CN55-A 8 M41_CONT2 CN158- 1 DRV
51
CN158- 3 H/L
CN55-A11 M41_EN CN61- 2 M4_PGND CN158- 4 PGND
CN55-A12 M41_MODE1 CN61- 3 M80_DRV -3
CN55-A13 M41_CLK CN139- 1 DRV
CN61- 4 M80_PGND -2 Pellet supply cooling fan motor
CN55-A14 M31_CONT2 CN139- 2 EM M4
-1
CN55-A15 M31_CONT1 CN139- 3 PGND
CN55-A16 M31_F/R
CN55-A17 M31_EN CN71- 1 M11_24V CN103- 3 COM
CN55-A18 M31_MODE1 CN71- 2 M11_24V CN103- 9 COM
3
3
4
4
CN57-A 5 M74_CLK
CN57-A 6 M74_CONT -6
CN57-A 7 M32_H/L CN81-A 1 M19_24V CN109- 1 COM
-5
CN57-A 8 M32_F/R CN81-A 2 M19_24V CN109- 2 COM
-4
CN57-A 9 M32_CLK CN81-A 3 M19_DRV_A CN109- 3 A
-3 M19 Clamp entranse movement motor
CN57-A10 M32_CONT CN81-A 4 M19_DRV_A/ CN109- 4 A/
-2
CN57-A11 M91_H/L CN81-A 5 M19_DRV_B CN109- 5 B
-1
CN57-A12 M91_F/R CN81-A 6 M19_DRV_B/ CN109- 6 B/
CN57-A13 M91_CLK
CN57-A14 M91_CONT CN81-A 7 M13_DRV1 CN105- 2 DRV1 SC switchback release motor
CN57-A15 M2_H/L CN81-A 8 M13_DRV2 CN105- 1 DRV2
M13
CN57-A16 M2_F/R
CN57-A17 M2_CLK -2
CN81-A 9 M18_DRV1 CN108- 1 DRV1 SC roller release motor
CN57-A18 M2_CONT -1 M18
CN81-A10 M18_DRV2 CN108- 2 DRV2
CN57-B 1 SOUT17
Sub compile
CN81-A11 NC
CN57-B 2 CL72_CONT -2
CN57-B 3 CL71_CONT CN81-B 1 SD12_24V CN145- 1 24V SC stopper solenoid
-1 SD12
CN57-B 4 SD80_F/R CN81-B 2 SD12_DRV CN145- 2 DRV
CN57-B 5 SD80_CONT
J21- 2 -1 -2
CN57-B 6 SD72_CONT CN81-B 3 SD11_24V CN144- 1 24V FD alignment solenoid
J21- 1 -2 -1 SD11
CN57-B 7 SD71_CONT CN81-B 4 SD11_DRV CN144- 2 DRV
CN57-B 8 SD43_CONT
CN57-B 9 SD42_CONT
CN57-B10 SD41_CONT
CN57-B11 SD32_CONT J20-10 -1 -2
CN57-B12 SD31_CONT CN81-B 5 M20_DRV1 CN110- 1 DRV1 Clamp entranse roller release motor
J20- 9 -2 -1 M20
CN57-B13 SD21_CONT CN81-B 6 M20_DRV2 CN110- 2 DRV2
101
5
5
CN57-B14 SD13_CONT
J20- 8 -3 -2
CN57-B15 SD12_CONT CN81-B 7 SD13_24V CN146- 1 24V SC pressure arm solenoid
J20- 7 -4 -1 SD13
CN57-B16 SD11_CONT CN81-B 8 SD13_DRV CN146- 2 DRV
CN57-B17 SD4_CONT
CN57-B18 SD3_CONT
-2
CN81-B 9 SD91_24V CN157- 1 24V Straight gate solenoid
-1 SD91
CN81-B10 SD91_DRV CN157- 2 DRV
CN60- 1 SUB1_CONT2 CN81-B11 NC
CN60- 2 SUB1_CONT1
CN60- 3 SUB1_F/R
CN60- 4 SUB1_EN
CN73- 1 M21_24V CN111- 3 COM
CN60- 5 SUB1_MODE1
CN73- 2 M21_24V CN111- 9 COM
CN60- 6 SUB1_CLK
CN73- 3 M21_DRV_A CN111- 1 A
CN73- 4 M21_DRV_A/ CN111- 5 A/ M21 Clamp alignment motor
CN73- 5 M21_DRV_B CN111- 7 B
PBDB(1/2)
CN56-A10 M47_EN
CN56-A11 M47_MODE1
6
6
CN56-A12 M47_CLK
CN56-A13 M46_CONT2 CN82- 5 M23_DRV1 CN113- 1 DRV1
CN56-A14 M46_CONT1 CN82- 6 M23_DRV2 CN113- 2 DRV2
M23 Clamp rotation motor
CN56-A15 M46_F/R CN82- 7 RSV_SD1_24V
CN56-A16 M46_EN CN82- 8 RSV_SD1_DRV
4
CN56-B 2 M80_CONT
(DB CN70) CN114- 3 A/ M31 Glue tank movement motor
8
CN58-A 1 SOUT14 -2
CN148- 1 24V Glue tank up solenoid /2
CN58-A 2 SOUT13 -1 SD33
CN148- 2 DRV
CN58-A 3 M48_CONT
CN58-A 4 M34_F/R -2
J42-B 9 -B 3
CN58-A 5 M34_CONT CN83- 14 SD32_24V CN149- 1 24V
J42-B 8 -B 4 -1 SD32 Glue equalize up solenoid
CN58-A 6 M33_F/R CN83- 15 SD32_DRV CN149- 2 DRV
CN58-A 7 M33_CONT
CN58-A 8 M23_F/R -2
J41-18 -1
CN58-A 9 M23_CONT CN83- 16 M34_DRV1 CN117- 1 DRV1 Pellet supply arm motor
J41-17 -2 -1 M34
CN58-A10 M23_F/R CN83- 17 M34_DRV2 CN117- 2 DRV2
Glue tank
CN58-A11 M22_CONT
CN58-A12 M20_F/R PS #110
J47- 4 -1
CN58-A13 M20_CONT CN68- 1 24V1_OUT FT-1
CN58-A14 M18_F/R CN68- 2 PGND(NC) PS #110 MS 1 Pellet supply door switch
J47- 3 -2
CN58-A15 M18_CONT CN68- 3 24V1_IN FT-2
CN58-A16 M13_F/R
CN58-A17 M13_CONT J47- 2 -3 -2
CN83- 4 M33_DRV1 CN116- 1 DRV1 Pellet supply motor
CN58-B 1 SOUT16 J47- 1 -4 -1 M33
CN83- 5 M33_DRV2 CN116- 2 DRV2
CN58-B 2 SOUT15 CN68- 6 PGND(NC)
CN58-B 3 M73_F/R
CN58-B 4 M73_CONT
CN58-B 5 M64_F/R
CN58-B 6 M64_CONT
CN58-B 7 M63_F/R
CN58-B 8 M63_CONT
CN58-B 9 M60_F/R
8
8
CN58-B10 M60_CONT
CN58-B11 M50_F/R
CN58-B12 M50_CONT
CN58-B13 M49_F/R
CN58-B14 M49_CONT
CN58-B15 M48_F/R
CN58-B16 SOUT10
CN58-B17 SOUT9
CN59-A 1 M2_LD
CN59-A 2 AD_SUB1
CN59-A 3 VR71_SIG
CN59-A 4 PS82_SIG
CN59-A 5 PS77_SIG
CN59-A 6 PS76_SIG
CN59-A 7 PS75_SIG
CN59-A 8 PS74_SIG
CN59-A 9 SIN_9
CN59-A10 PS71_SIG
CN59-A11 TRAY_SET(SW71)
CN59-A12 24V_DEC
CN59-B 1 SIN_7
CN59-B 2 M81_LD
CN59-B 3 AD_SUB2
CN59-B 4 M4_LD
CN59-B 5 PS92_SIG
9
9
CN59-B 6 PS91_SIG
CN59-B 7 M80_LD
CN59-B 8 M74_LD
CN59-B 9 M72_LD
CN59-B10 M71_LD
CN59-B11 M32_LD
CN59-B12 M91_LD
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
H
D
C
G
CN75- 1 M46_24V CN123- 5 COM
CN75- 2 M46_24V CN123- 2 COM
CN75- 3 M46_DRV_A CN123- 4 A
CN75- 4 M46_DRV_A/ CN123- 6 A/ M46 Cover paper table up down motor /Fr
CN75- 5 M46_DRV_B CN123- 3 B
CN75- 6 M46_DRV_B/ CN123- 1 B/
10
10
J94-13 -1
CN76- 1 M41_24V CN118- 5 COM
J94-12 -2
CN76- 2 M41_24V CN118- 2 COM
Field Service Ver3.0 Nov.2006
J94-11 -3
CN76- 3 M41_DRV_A CN118- 4 A
J94-10 -4 M41 Cover paper alignment motor
CN76- 4 M41_DRV_A/ CN118- 6 A/
J94- 9 -5
CN76- 5 M41_DRV_B CN118- 3 B
J94- 8 -6
CN76- 6 M41_DRV_B/ CN118- 1 B/
J94- 7 -7
CN76- 7 NC
J94- 6 -8
CN76- 8 M42_24V CN119- 3 COM
J94- 5 -9
CN76- 9 M42_24V CN119- 9 COM
J94- 4 -10
CN76- 10 M42_DRV_A CN119- 1 A
J94- 3 -11 M42 Booklet exit motor
CN76- 11 M42_DRV_A/ CN119- 5 A/
J94- 2 -12
CN76- 12 M42_DRV_B CN119- 7 B
J94- 1 -13
CN76- 13 M42_DRV_B/ CN119-11 B/
J95-12 -1
CN77- 1 M43_24V CN120- 3 COM
J95-11 -2
CN77- 2 M43_24V CN120- 9 COM
J95-10 -3
CN77- 3 M43_DRV_A CN120- 1 A
J95- 9 -4 M43 Cover paper conveyance arm motor /Rt
CN77- 4 M43_DRV_A/ CN120- 5 A/
J95- 8 -5
CN77- 5 M43_DRV_B CN120- 7 B
J95- 7 -6
CN77- 6 M43_DRV_B/ CN120-11 B/
CN77- 7 NC
J95- 6 -7
CN77- 8 M44_24V CN121- 3 COM
J95- 5 -8
CN77- 9 M44_24V CN121- 9 COM
11
11
J95- 4 -9
CN77- 10 M44_DRV_A CN121- 1 A
J95- 3 -10 M44 Cover paper conveyance arm motor /Lt
CN77- 11 M44_DRV_A/ CN121- 5 A/
J95- 2 -11
CN77- 12 M44_DRV_B CN121- 7 B
J95- 1 -12
CN77- 13 M44_DRV_B/ CN121-11 B/
J56- 6 -1
CN74- 1 M45_24V CN122- 5 COM
J56- 5 -2
CN74- 2 M45_24V CN122- 2 COM
J56- 4 -3
CN74- 3 M45_DRV_A CN122- 4 A
J56- 3 -4 M45 Cover paper conveyance motor
CN74- 4 M45_DRV_A/ CN122- 6 A/
J56- 2 -5
CN74- 5 M45_DRV_B CN122- 3 B
J56- 1 -6
CN74- 5 M45_DRV_B/ CN122- 1 B/
J91- 9 -1
Cover paper table
J91- 8 -2
CN84- 1 M49_DRV1 CN126- 1 DRV1 Cover paper folding motor /Lt
J91- 7 -3 M49
CN84- 2 M49_DRV2 CN126- 2 DRV2
J91- 6 -4
CN84- 3 M48_DRV1 CN125- 1 DRV1 Cover paper folding motor /Rt
J91- 5 -5 M48
CN84- 4 M48_DRV2 CN125- 2 DRV2
12
12
J91- 2 -8 -2
CN84- 7 SD41_24V CN150- 1 24V Cutter HP sensor
J91- 1 -9 -1 SD41
CN84- 8 SD41_DRV CN150- 2 DRV
CN84- 9 SD42_24V
CN84- 10 SD42_DRV
CN84- 11 SD43_24V
CN84- 12 SD43_DRV
CN78- 1 NC
CN78- 2 M61_24V CN129- 3 COM
CN78- 3 M61_24V CN129- 9 COM
CN78- 4 M61_DRV_A CN129- 1 A Booklet conveyance belt motor
CN78- 5 M61_DRV_A/ CN129- 5 A/ M61
CN78- 6 M61_DRV_B CN129- 7 B
CN78- 7 M61_DRV_B/ CN129-11 B/
J61-15 -1 -6
CN85-A 1 M62_24V CN130- 1 COM
J61-14 -2 -5
CN85-A 2 M62_24V CN130- 2 COM
J61-13 -3 -4
CN85-A 3 M62_DRV_A CN130- 3 A
J61-12 -4 -3 M62 Booklet conveyance belt movement motor
CN85-A 4 M62_DRV_A/ CN130- 4 A/
J61-11 -5 -2
CN85-A 5 M62_DRV_B CN130- 5 B
J61-10 -6 -1
CN85-A 6 M62_DRV_B/ CN130- 6 B/
13
13
J62-18 -1 -6
CN85-B 1 M65_24V CN133- 1 COM
Booklet
J62-17 -2 -5
CN85-B 2 M65_24V CN133- 2 COM
J62-16 -3 -4
CN85-B 3 M65_DRV_A CN133- 3 A
J62-15 -4 -3 M65 Booklet stopper motor
CN85-B 4 M65_DRV_A/ CN133- 4 A/
J62-14 -5 -2
CN85-B 5 M65_DRV_B CN133- 5 B
J62-13 -6 -1
CN85-B 6 M65_DRV_B/ CN133- 6 B/
J64- 8
CN85-B 7 M60_DRV1
J64- 7
CN85-B 8 M60_DRV2
PBDB(2/2)
CN69- 1 M64_DRV1 CN132- 1 DRV1
CN69- 2 M64_DRV2 CN132- 2 DRV2
M64 Booklet movement motor
CN69- 3 PGND(NC) -2
J92- 2 -1
CN69- 4 SD61_DRV1 J92- 1 -2 -1 CN153- 1 DRV1
CN153- 2 DRV2
SD61 Booklet door solenoid
CN69- 5 SD61_DRV1
14
14
CN86- 14 RSV_SD2_24V
CN86- 15 RSV_SD2_DRV
J73-15 -15
CN87-A 1 24V1
J73-21 -21
CN87-A 2 PGND
CN87-A 3 NC
CN87-A 4 NC
J73-14 -14
CN87-A 5 5V
J73-12 -12
CN87-A 6 TRAY_SET
J73- 9 -9
CN87-A 7 M71_LD
J73-10 -10
CN87-A 8 M72_LD
J73- 1 -1
CN87-A 9 M73_DRV1 CN136- 1 DRV1 Cover paper tray lift motor
J73-13 -13 M73
CN87-A10 M73_DRV2 CN136- 2 DRV2
-2
CN154- 1 24V
J73-19 -19 -1 MC71 Cover paper pick up clutch
CN87-A11 CL71_DRV CN154- 2 DRV
-2
CN155- 1 24V
J73-18 -18 -1 MC72 Cover paper separation clutch
CN87-A12 CL72_DRV CN155- 2 DRV
15
15
-2
CN151- 1 24V
J73-20 -20 -1 SD71 Cover paper pick up solenoid
CN87-B 1 SD71_DRV CN151- 2 DRV
J83-3 -1
CN222- 3 SGND
J73- 2 -2 J83-2 -2
CN87-B 2 PS71_SIG CN222- 2 SIG PS71 Cover paper empty sensor
J83-1 -3
CN222- 1 5V
CN231- 3 SGND
J73- 4 -4 Cover paper tray knob sensor
CN87-B 5 PS82_SIG CN231- 2 SIG PS82
CN231- 1 5V
J80-3 -4
Cover paper tray
CN223- 3 SGND
J73- 3 -3 J80-2 -5
Cover paper feed
CN87-B 6 PS74_SIG CN223- 2 SIG PS74 Cover paper tray upper limit sensor
J80-1 -6
CN223- 1 5V
CN51-4 PGND J80-6 -1
CN51-3 PGND CN224- 3 SGND
J73-23 -23 J80-5 -2 Cover paper conveyance sensor /1
CN51-2 24V1 CN87-B 7 PS75_SIG CN224- 2 SIG PS75
J80-4 -3
CN51-1 24V1 CN87-B 8 RSV_PS1_SIG CN224- 1 5V
16
16
CN87-B 9 NC
CN87-B10 NC
J73-22 -22
CN87-B11 SGND
J73-17 -17 J81-3 -1 -3
CN87-B12 M71/72_DRV CN134- 1 DRV
J81-2 -2 -2
J81-1 -3 -1 CN134- 2 EM M71 Cover paper tray fan /1
J73-24 CN134- 3 PGND
CN52-6 PGND
CN52-5 PGND CN64- 1 RSV_M2_DRV1 J82-3 -1 -3
CN52-4 PGND CN64- 2 RSV_M2_DRV2 J82-2 -2 -2 CN135- 1 DRV
CN52-3 24V2 CN64- 3 RSV_M3_DRV1 J82-1 -3 -1 CN135- 2 EM M72 Cover paper tray fan /2
CN52-2 24V2 CN64- 4 RSV_M3_DRV2 -24 CN135- 3 PGND
CN52-1 24V2 CN64- 5 AD_SUB2
J7-4
J7-3
J7-1
J7-2
J2-4
J2-3
CN88- 12 5V
CN88- 11 AD_SUB1
CN88- 10 SGND
CN88- 9 5V
CN88- 8 RSV_PS2_SIG
CN88- 7 SGND
CN88- 6 5V
CN88- 5 PS92_SIG
CN88- 4 SGND
CN88- 3 5V
CN88- 2 PS91_SIG
CN88- 1 SGND
CN89- 11 M91_5V
CN89- 10 M91_SGND
CN89- 9 M91_CONT
CN89- 8 M91_CLK
CN89- 7 M91_F/R
CN89- 6 M91_LD
CN89- 5 M91_H/L
CN89- 4 M91_PGND
CN89- 3 M91_PGND
CN89- 2 M91_24V
CN89- 1 M91_24V
AC CODE
WIT
WIT
BLK
17
17
CN98-3 -V/PGND
CN98-2 -V/PGND
AC INRET
CN66-1 :LINE(H)
MS2
CN98-1 -V/PGND
BLK
WIT
BLK
WIT
DCPU/2
(with interlock)
CN47-1A
CN47-2A
FT5
FT6
CN93-1 PS_ON
Front door switch
J8-4
J8-2
J8-1
J8-3
CN97-5 㧗V/24V
WIT
BLK
BLK FT7
WIT FT8
CN97-3 -V/PGND
CN97-2 -V/PGND
CN67-1 :LINE(H)
20
CN97-1 -V/PGND
CN248-1B
CN248-2B
CBR
14
CN239-2A
CN239-1A
DCPU/1
WIT
15
CN92-1 PS_ON
MS3
FT9
Circuit breaker
FT10
(without interlock)
16
CN92-2 PGND
MS4
BLK
17
18
CN248-1A
CN248-2A
CN239-2B
CN239-1B
CN95-1
11
18
18
WIT
BLK
WIT
BLK
CN95-3 J2-2
㧦-V/SGND CN65-1 :LINE(H) WIT
Upper door switch
DCPU/3
CN95-4
1
2
NF1
12
102
㧦-V/SGND
Noise filter
FT13
FT14
BLK BLK
WIT WIT
I
F
E
B
A
H
D
C
G
18. OVERALL WIRING DIAGRAM
P
K
R
N
Q
O
M
CN170- 3 S.GND J11- 1 -3 J10- 9 -12
CN30-A 1 SGND CN15-A20 M15_MODE1
CN170- 2 SIG J11- 2 -2 J10-10 -11
Entrance sensor PS1 CN30-A 2 PS1_SIG CN15-A19 M15_CLK
CN170- 1 5V J11- 3 -1 J10-11 -10
CN30-A 3 5V CN15-A18 M12_CONT2
CN15-A17 M12_CONT1
CN15-A16 M12_F/R
J12- 1 -3 J10-12 -9
18.16 PB-501 3/4
1
1
CN15-A11 M11_CONT1
CN173- 3 S.GND J17- 1 -6 J10-15 -6
CN30-A 7 SGND CN15-A10 M11_F/R
CN173- 2 SIG J17- 2 -5 J10-16 -5
Sub tray exit sensor PS4 CN30-A 8 PS4_SIG CN15-A 9 M11_EN
CN173- 1 5V J17- 3 -4 J10-17 -4
CN30-A 9 5V CN15-A 8 M11_MODE1
CN15-A 7 M11_CLK
Field Service Ver3.0 Nov.2006
CN15-A 6 M1_CONT2
CN174- 3 S.GND J17- 4 -3 J10-18 -3
CN30-A10 SGND CN15-A 5 M1_CONT1
CN174- 2 SIG J17- 5 -2 J10-19 -2
Sub tray full sensor PS5 CN30-A11 SIN_10 CN15-A 4 M1_F/R
CN174- 1 5V J17- 6 -1 J10-20 -1
CN30-A12 5V CN15-A 3 M1_EN
CN15-A 2 M1_MODE1
CN15-A 1 M1_CLK
CN30-A13 SGND CN15-B20 M4_CONT
CN30-A14 PS5_SIG CN15-B19 M66_F/R
CN30-A15 5V CN15-B18 M66_CONT
CN15-B17 SD91_CONT
CN15-B16 M21_CONT2
CN171- 3 S.GND J16- 3 -5
CN30-B 1 SGND CN15-B15 M21_CONT1
CN171- 2 SIG J16- 4 -4
SC entrance sensor PS2 CN30-B 2 PS2_SIG CN15-B14 M21_F/R
CN171- 1 5V J16- 5 -3
CN30-B 3 5V CN15-B13 M21_EN
CN15-B12 M21_MODE1
CN15-B11 M21_CLK
CN240- 2 SIG J16- 6 -2
CN30-B 4 SW1 CN15-B10 M17_CONT2
Upper door switch SW1 CN15-B 9 M17_CONT1
CN240- 1 S.GND J16- 7 -1
CN30-B 5 SGND CN15-B 8 M17_F/R
Conveyance
CN15-B 7 M17_EN
CN15-B 6 M17_MODE1
2
2
CN16-A19 M43_CLK
1
CN30-B12 H1_CONT CN16-A18 M42_CONT2
2
(ACDB CN43) CN30-B13 H2_CONT CN16-A17 M42_CONT1
3 CN30-B14 RL_CONT CN16-A16 M42_F/R
CN30-B15 NC CN16-A15 M42_EN
CN16-A14 M42_MODE1
CN16-A13 M42_CLK
CN16-A12 M41_CONT2
CN175- 3 S.GND CN31-A 1 SGND CN16-A11 M41_CONT1
SC switchback arm pressure CN16-A10 M41_F/R
PS12 CN175- 2 SIG CN31-A 2 PS12_SIG
detection sensor CN175- 1 5V CN31-A 3 5V CN16-A 9 M41_EN
CN16-A 8 M41_MODE1
CN16-A 7 M41_CLK
CN176- 3 S.GND CN31-A 4 SGND CN16-A 6 M31_CONT2
SC switchback spring pressure CN16-A 5 M31_CONT1
PS13 CN176- 2 SIG CN31-A 5 PS13_SIG
detection sensor CN176- 1 5V CN31-A 6 5V CN16-A 4 M31_F/R
CN16-A 3 M31_EN
CN16-A 2 M31_MODE1
CN177- 3 S.GND J24- 1 -3 CN16-A 1 M31_CLK
CN31-A 7 SGND
CN177- 2 SIG J24- 2 -2 CN16-B19 SOUT23
CN31-A 8 PS14_SIG
3
3
Sub compile
CN31-B10 SGND CN16-B 1 M43_MODE1
CN31-B11 SIN_11
CN31-B12 5V
CN18-A18 SD2_CONT
CN18-A17 SD1_CONT
CN185- 3 S.GND CN32-A 1 SGND CN18-A16 M74_H/L
Clamp rotation HP sensor PS24 CN185- 2 SIG CN32-A 2 PS24_SIG CN18-A15 M74_F/R
CN185- 1 5V CN32-A 3 5V CN18-A14 M74_CLK
CN18-A13 M74_CONT
CN182- 3 S.GND J30-A 1 -A13
CN32-A 4 SGND CN18-A12 M32_H/L
4
4
Clamp
CN187- 3 S.GND CN32-B 4 SGND CN18-B 8 SD32_CONT
CN187- 2 SIG J30-B 2 -B12
Cover paper table upper limit sensor /Fr PS26 CN32-B 5 PS26_SIG CN18-B 7 SD31_CONT
CN187- 1 5V J30-B 3 -B11
CN32-B 6 5V CN18-B 6 SD21_CONT
CN188- 3 S.GND J30-B 4 -B10 CN18-B 5 SD13_CONT
CN32-B 7 SGND
CN188- 2 SIG J30-B 5 -B 9 CN18-B 4 SD12_CONT
Cover paper table upper limit sensor /Rr PS27 CN32-B 8 PS27_SIG
J30-B 6 -B 8
101
CN18-B 3 SD11_CONT
5
5
CN188- 1 5V CN32-B 9 5V
J30-B 9 -B 5 CN18-B 2 SD4_CONT
CN160- 3 S.GND CN32-B10 LED21_CONT CN18-B 1 SD3_CONT
Clamp paper LED LED21 CN160- 2 NC
CN160- 1 5V J30-B10 -B 4
CN32-B11 SGND
CN190- 1 S.GND J30-B11 -B 3
CN32-B12 SGND CN21- 6 SUB1_CONT2
CN190- 2 SIG J30-B12 -B 2
Booklet thickness sensor PS29 CN32-B13 PS29_SIG CN21- 5 SUB1_CONT1
CN190- 3 5V J30-B13 -B 1
CN32-B14 5V CN21- 4 SUB1_F/R
CN21- 3 SUB1_EN
PBCB(1/2)
CN21- 2 SUB1_MODE1
CN21- 1 SUB1_CLK
CN192- 3 SIG J42-B 5 -B 7
CN33- 1 PS32_SIG
Glue apply position detection sensor PS32 CN192- 2 NC
CN192- 1 SGND J42-B 6 -B 6
CN33- 2 SGND
CN161- 3 S.GND J42-B 7 -B 5 CN17-A18 M61_CONT2
CN33- 3 LED31
CN161- 2 NC CN17-A17 M61_CONT1
Glue apply position LED LED31 J42-B 8 -B 4 CN17-A16 M61_F/R
CN161- 1 5V CN33- 4 5V
CN17-A15 M61_EN
J42-B 9 -B 3 CN17-A14 M61_MODE1
J42-B10 -B 2 CN17-A13 M61_CLK
J42-B11 -B 1 CN17-A12 M47_CONT2
CN17-A11 M47_CONT1
CN17-A10 M47_F/R
CN194- 3 S.GND J41- 3 -16 CN17-A 9 M47_EN
CN33- 5 SGND
CN194- 2 SIG J41- 4 -15 CN17-A 8 M47_MODE1
Pellet remain sensor PS36 CN33- 6 PS36_SIG
CN194- 1 5V J41- 5 -14 CN17-A 7 M47_CLK
CN33- 7 5V
CN195- 3 SIG J41- 6 -13 CN17-A 6 M46_CONT2
CN33- 8 PS37_SIG
6
6
CN19-A10 M23_F/R
CN19-A 9 M23_CONT
J90-A 1 -A19 CN19-A 8 M22_F/R
CN199- 3 S.GND CN35-A 1 SGND CN19-A 7 M22_CONT
CN199- 2 SIG J90-A 2 -A18
Cover paper conveyance arm HP sensor /Rt PS42 CN35-A 2 PS42_SIG CN19-A 6 M20_F/R
CN199- 1 5V J90-A 3 -A17
CN35-A 3 5V CN19-A 5 M20_CONT
CN205- 3 S.GND J90-A 4 -A16 CN19-A 4 M18_F/R
CN35-A 4 SGND
CN205- 2 SIG J90-A 5 -A15 CN19-A 3 M18_CONT
Cover paper folding plate HP sensor /Rt PS48 CN35-A 5 PS48_SIG
CN205- 1 5V J90-A 6 -A14 CN19-A 2 M13_F/R
CN35-A 6 5V
CN198- 3 S.GND J90-A 7 -A13 CN19-A 1 M13_CONT
CN35-A 7 SGND
CN198- 2 SIG J90-A 8 -A12 CN19-B17 SOUT16
Cover paper alignment HP sensor PS41 CN35-A 8 PS41_SIG
CN198- 1 5V J90-A 9 -A11 CN19-B16 SOUT15
CN35-A 9 5V
J90-A10 -A10 CN19-B15 M73_F/R
CN200- 3 S.GND CN35-A10 SGND CN19-B14 M73_CONT
CN200- 2 SIG J90-A11 -A 9
Cover paper conveyance arm HP sensor /Lt PS43 CN35-A11 PS43_SIG CN19-B13 M64_F/R
CN200- 1 5V J90-A12 -A 8
CN35-A12 5V CN19-B12 M64_CONT
Cutter unit CN19-B11 M63_F/R
CN241- * NO Yellow-3 CN166-4 J53-3 -7 J90-A13 -A 7 CN19-B10 M63_CONT
CN35-A13 SW41
Cutter HP sensor CN19-B 9 M60_F/R
(Within the cutter unit)
SW41 Brown-4 CN166-3 J53-4 -6 J90-A14 -A 6 CN19-B 8 M60_CONT
CN241- * COM CN35-A14 SGND
Yellow-5 CN166-2 J53-5 -5 J90-A15 -A 5 CN19-B 7 M50_F/R
CN242- * NO CN35-A15 SW42 CN19-B 6 M50_CONT
8
8
CN35-B13 SGND
CN208- 2 SIG J90-B14 -B 6 CN20-B 7 PS91_SIG
Cover paper folding plate position sensor PS51 CN35-B14 PS51_SIG
CN208- 1 5V J90-B15 -B 5 CN20-B 6 M80_LD
CN35-B15 5V
9
9
P
K
R
N
Q
O
M
18. OVERALL WIRING DIAGRAM
P
K
R
N
Q
O
M
CN218- 3 S.GND J62- 7 -12
CN36-A 1 SGND
CN218- 2 SIG J62- 8 -11
Booklet sensor /1 PS66 CN36-A 2 PS66_SIG
CN218- 1 5V J62- 9 -10
CN36-A 3 5V
10
10
-6
CN36-A13 SGND
-5
CN36-A14 PS59_SIG
-4 CN 7-A20 NSW5-2
CN36-A15 5V
-3 CN 7-A19 NSW5-1
CN36-A16 SGND
-2 CN 7-A18 NSW4-8
CN36-A17 PS60_SIG
-1 CN 7-A17 NSW4-4
CN36-A18 5V
CN 7-A16 NSW4-2
CN217- 3 SIG CN36-A19 PS65_SIG CN 7-A15 NSW4-1
Booklet load limit sensor PS65 CN217- 2 NC CN 7-A14 NSW3-8
CN217- 1 SGND CN36-A20 SGND CN 7-A13 NSW3-4
CN 7-A12 NSW3-2
CN 7-A11 NSW3-1
CN213- 3 S.GND J61- 7 -9 CN 7-A10 NSW2-8
CN36-B 1 SGND
CN213- 2 SIG J61- 8 -8 CN 7-A 9 NSW2-4
Booklet end sensor PS61 CN36-B 2 PS61_SIG
CN213- 1 5V J61- 9 -7 CN 7-A 8 NSW2-2
CN36-B 3 5V
J61-10 -6 CN 7-A 7 NSW2-1
Booklet conveyance belt CN214- 3 S.GND CN36-B 4 SGND CN 7-A 6 NSW1-8
CN214- 2 SIG J61-11 -5
PS62 CN36-B 5 PS62_SIG CN 7-A 5 NSW1-4
movement HP sensor CN214- 1 5V J61-12 -4
CN36-B 6 5V CN 7-A 4 NSW1-2
Booklet
J65- 1 -3 J61-13 -3 CN 7-A 3 NSW1-1
Booklet conveyance CN216- 3 S.GND CN36-B 7 SGND CN 7-A 2 5V
11
11
12
12
Booklet
Waste box set sensor PS81 CN230- 2 SIG CN37- 11 PS81_SIG CN 9- 1 MONI_TXD
CN230- 1 5V CN37- 12 5V CN 9- 2 SGND
CN 9- 3 MONI_RXD
CN204- 3 S.GND J57-13 -6
CN37- 13 SGND
CN204- 2 SIG J57-14 -5
Cover paper PS47 CN37- 14 PS47_SIG
CN204- 1 5V J57-15 -4
table HP sensor /Fr CN37- 15 5V
J57-16 -3 CN10-A20 NSW5-2
CN210- 3 S.GND CN37- 16 SGND
J57-17 -2 CN10-A19 NSW5-1
Cover paper PS53 CN210- 2 SIG CN37- 17 PS53_SIG
J57-18 -1 CN10-A18 NSW4-8
table HP sensor /Rr CN210- 1 5V CN37- 18 5V
CN10-A17 NSW4-4
CN10-A16 NSW4-2
J74- 1 -4 CN10-A15 NSW4-1
CN246- 3 GND CN38- 1 AGND
Multi feed J74- 2 -3 CN10-A14 NSW3-8
MFDTB71CN246- 1 CLK㧗 CN38- 2 JCLK_OUT
J74- 3 -2 CN10-A13 NSW3-4
detection board /1 CN246- 2 CLK- CN38- 3 JCLK_AGND
13
13
14
14
CN13-A18 NSW4-8
CN13-A17 NSW4-4
CN49- 7 MAN_SW2
CN13-A16 NSW4-2
CN49- 6 MAN_SW3
CN13-A15 NSW4-1
CN49- 5 NC
CN13-A14 NSW3-8
OB/2
CN49- 4 MAN_LED2
CN23-1 TXD CN13-A13 NSW3-4
CN49- 3 MAN_LED3
CN23-2 RXD CN13-A12 NSW3-2
CN49- 2 MAN_LED4
CN23-3 SCK CN13-A11 NSW3-1
CN49- 1 NC
CN23-4 RTS CN13-A10 NSW2-8
CN23-5 CTS CN13-A 9 NSW2-4
CN13-A 8 NSW2-2
CN13-A 7 NSW2-1
CN238-2 CN13-A 6 NSW1-8
CN29-1 SYS_SIN
CN238-1 CN13-A 5 NSW1-4
CN29-2 SYS_RTS
CN13-A 4 NSW1-2
CN29-3 ISW_SIN
CN13-A 3 NSW1-1
CN29-4 ISW_RTS
CN237-1 MTXD CN13-A 2 5V
CN24-1 FS_SOUT CN13-A 1 5V
CN237-2 SG
CN24-2 S.GND CN13-B20 SGND
CN237-3 MCTS
CN24-3 FS_CTS CN13-B19 SGND
CN237-4 MRXD
CN24-4 FS_SIN CN13-B18 NC
CN237-5 SG
CN24-5 FSSET CN13-B17 NC
CN237-6 MRTS
CN24-6 FS_RTS CN13-B16 NC
CN24-7 BACK_PAPER CN13-B15 NC
CN24-8 NC CN13-B14 NC
CN236-1 PAPER_OUT CN13-B13 NC
CN236-2 SG CN13-B12 NLED7
16
16
CN13-B 9 NLED4
CN13-B 8 NLED3
CN13-B 7 NLED2
CN235-1 24V CN13-B 6 NLED1
CN235-2 5V CN13-B 5 NLED0
CN235-3 SG CN13-B 4 NSW7
CN235-4 PG CN13-B 3 NSW8
CN235-5 PG CN13-B 2 NSW6
CN235-6 FG CN13-B 1 NSW5-4
-1
-2
-3
-6
-5
-4
-3
-2
J3-4
J4-1
CN14- 1 /RES_CONT
CN14- 2 FWE_CNT1
CN14- 3 MD2
CN29-1 NC
-4
-3
-2
-1
-6
-5
-4
-3
-2
-1
CN14- 4 SGND
CN29-2 NC CN14- 5 TXD1_OUT
CN28-2
CN29-3 FNS2_RTS CN14- 6 SGND
CN28-1
CN29-4 FNS2_SIN CN14- 7 TXD1_IN
CN14- 8 5V
CN27-1 MTXD CN14- 9 5V
CN 2-1 SYS_SIN
CN27-2 SG
CN 2-2 S.GND
CN27-3 MCTS
19
CN27-5 SG
CN 2-5 S.GND
CN27-6 MRTS
CN 2-6 /SYS_CTS
15
CN44- 1 5V
CN 2-7 /PAPEROUT_1
16
CN44- 2 5V
17
CN25-1 24V
CN25-2 5V
Crimp
Symbol
CN25-3 SG
CN25-4 PG
CN25-5 PG CN46- 1 5V2 (MAIN_RL CONT)
11
CN25-6 FG
12
CN42- 2 SGND
CN42- 3 NC
13
CN42- 4 24V1
14
CN42- 5 PGND
3
CN43- 1 RL_CONT
Connector
2
CN45- 6 AC_N(24V2)
102
J44- 6 -6
J
P
K
R
N
Q
O
M
18. OVERALL WIRING DIAGRAM
Z
T
F
Y
X
V
S
P
K
E
B
A
U
R
N
H
D
C
Q
O
G
W
CN170- 3 S.GND J11- 1 -3 J10- 9 -12
CN30-A 1 SGND CN15-A20 M15_MODE1 CN54-A 1 M15_MODE1 CN70- 1 M1_24V CN100- 2 COM
CN170- 2 SIG J11- 2 -2 J10-10 -11
Entrance sensor PS1 CN30-A 2 PS1_SIG CN15-A19 M15_CLK CN54-A 2 M15_CLK CN70- 2 M1_24V CN100- 5 COM
CN170- 1 5V J11- 3 -1 J10-11 -10
CN30-A 3 5V CN15-A18 M12_CONT2 CN54-A 3 M12_CONT2 CN70- 3 M1_DRV_A CN100- 1 A
CN15-A17 M12_CONT1 CN54-A 4 M12_CONT1 CN70- 4 M1_DRV_A/ CN100- 3 A/ M1 Entrance conveyance motor
1
1
4
Cover paper entrance sensor PS3 CN172- 2 SIG CN30-A 5 PS3_SIG CN15-A14 M12_MODE1 CN54-A 7 M12_MODE1 CN70- 7 M31_24V
J12- 3 -1 J10-14 -7
5
CN172- 1 5V CN30-A 6 5V CN15-A13 M12_CLK CN54-A 8 M12_CLK CN70- 8 M31_24V
18.8 PB-501
6
CN15-A12 M11_CONT2 CN54-A 9 M11_CONT2 CN70- 9 M31_DRV_A
7
CN15-A11 M11_CONT1 CN54-A10 M11_CONT1 CN70- 10 M31_DRV_A/ (Glue tank movement motor M31)
J17- 1 -6 J10-15 -6
8
CN173- 3 S.GND CN30-A 7 SGND CN15-A10 M11_F/R CN54-A11 M11_F/R CN70- 11 M31_DRV_B
J17- 2 -5 J10-16 -5
9
Sub tray exit sensor PS4 CN173- 2 SIG CN30-A 8 PS4_SIG CN15-A 9 M11_EN CN54-A12 M11_EN CN70- 12 M31_DRV_B/
CN173- 1 5V J17- 3 -4 J10-17 -4
CN30-A 9 5V CN15-A 8 M11_MODE1 CN54-A13 M11_MODE1
CN15-A 7 M11_CLK CN54-A14 M11_CLK
CN15-A 6 M1_CONT2 CN54-A15 M1_CONT2 CN80-A 1 M2_24V CN101-11 24V
CN174- 3 S.GND J17- 4 -3 J10-18 -3
CN30-A10 SGND CN15-A 5 M1_CONT1 CN54-A16 M1_CONT1 CN80-A 2 M2_24V CN101-10 24V
CN174- 2 SIG J17- 5 -2 J10-19 -2
Sub tray full sensor PS5 CN30-A11 SIN_10 CN15-A 4 M1_F/R CN54-A17 M1_F/R CN80-A 3 M2_PGND CN101- 9 P.GND
Field Service Ver3.0 Nov.2006
2
CN80-A 9 M2_CONT CN101- 3 START/STOP
2
Conveyance
CN15-B 7 M17_EN CN54-B14 M17_EN J10-18 -3 -2
CN15-B 6 M17_MODE1 CN54-B15 M17_MODE1 CN80-B 3 SD3_24V CN142- 1 24V
J10-17 -4 -1 SD3 Sub tray gate solenoid
CN191- 3 S.GND CN30-B 6 SGND CN15-B 5 M17_CLK CN54-B16 M17_CLK CN80-B 4 SD3_DRV CN142- 2 DRV
Glue tank movement limit sensor PS31 CN191- 2 SIG CN30-B 7 PS31_SIG CN15-B 4 M15_CONT2 CN54-B17 M15_CONT2
J10-16 -5 -2
CN191- 1 5V CN30-B 8 5V CN15-B 3 M15_CONT1 CN54-B18 M15_CONT1 CN80-B 5 SD4_24V CN143- 1 24V
J10-15 -6 -1 SD4 Sub tray exit solenoid
CN193- 3 S.GND CN30-B 9 SGND CN15-B 2 M15_F/R CN54-B19 M15_F/R CN80-B 6 SD4_DRV CN143- 2 DRV
Glue tank HP sensor PS33 CN193- 2 SIG CN30-B10 PS33_SIG CN15-B 1 M15_EN CN54-B20 M15_EN
J10-14 -7 -2
CN193- 1 5V CN30-B11 SGND CN80-B 7 SD80_DRV1 CN153- 1 DRV1
J10-13 -8 -1 SD80 Front door lock solenoid
3
3
1
CN30-B12 H1_CONT
CN16-A17 M42_CONT1 CN55-A 3 M42_CONT1 CN80-B 9 M4_LD
2
(ACDB CN43) CN30-B13 H2_CONT CN138- 1 DRV
CN16-A16 M42_F/R CN55-A 4 M42_F/R CN80-B10 M80_LD
3
CN30-B14 RL_CONT CN138- 2 EM Exhaust fan /1
CN30-B15 NC CN16-A15 M42_EN CN55-A 5 M42_EN CN80-B11 M80_H/L CN138- 3 H/L M80
CN16-A14 M42_MODE1 CN55-A 6 M42_MODE1 CN80-B12 M81_LD
51
CN138- 4 PGND
CN16-A13 M42_CLK CN55-A 7 M42_CLK CN80-B13 M81_H/L
52
CN16-A12 M41_CONT2 CN55-A 8 M41_CONT2 CN158- 1 DRV
CN16-A11 M41_CONT1 CN55-A 9 M41_CONT1
51
CN158- 3 H/L
Conveyance/Main frame
4
4
Sub compile
CN31-B10 SGND CN16-B 1 M43_MODE1 CN55-B19 M43_MODE1 CN72- 7 NC
5
5
6
6
CN81-A11 NC
CN189- 3 SIG J33- 2 -1 J30-B 7 -B 7 CN18-B17 CL72_CONT CN57-B 2 CL72_CONT -2
CN32-A13 PS28_SIG CN81-B 1 SD12_24V CN145- 1 24V
CN189- 2 NC CN18-B16 CL71_CONT CN57-B 3 CL71_CONT -1 SD12 SC stopper solenoid
Clamp paper sensor PS28 J33- 1 -2 J30-B 8 -B 6 CN18-B15 SD80_F/R CN57-B 4 SD80_F/R CN81-B 2 SD12_DRV CN145- 2 DRV
CN189- 1 SGND CN32-A14 SGND
CN18-B14 SD80_CONT CN57-B 5 SD80_CONT
J21- 2 -1 -2
J30-A10 -A 4 CN18-B13 SD72_CONT CN57-B 6 SD72_CONT CN81-B 3 SD11_24V CN144- 1 24V FD alignment solenoid
CN186- 3 S.GND CN32-B 1 SGND J21- 1 -2 -1 SD11
J30-A11 -A 3 CN18-B12 SD71_CONT CN57-B 7 SD71_CONT CN81-B 4 SD11_DRV CN144- 2 DRV
Clamp rotation pressure sensor PS25 CN186- 2 SIG CN32-B 2 PS25_SIG CN18-B11 SD43_CONT CN57-B 8 SD43_CONT
CN186- 1 5V J30-A12 -A 2
CN32-B 3 5V CN18-B10 SD42_CONT CN57-B 9 SD42_CONT
J30-A13 -A 1
CN18-B 9 SD41_CONT CN57-B10 SD41_CONT
J30-B 1 -B13
Clamp
CN187- 3 S.GND CN32-B 4 SGND CN18-B 8 SD32_CONT CN57-B11 SD32_CONT J20-10 -1 -2
CN187- 2 SIG J30-B 2 -B12 CN81-B 5 M20_DRV1 CN110- 1 DRV1 Clamp entranse roller release motor
Cover paper table upper limit sensor /Fr PS26 CN32-B 5 PS26_SIG CN18-B 7 SD31_CONT CN57-B12 SD31_CONT J20- 9 -2 -1 M20
CN187- 1 5V J30-B 3 -B11 CN81-B 6 M20_DRV2 CN110- 2 DRV2
CN32-B 6 5V CN18-B 6 SD21_CONT CN57-B13 SD21_CONT
CN188- 3 S.GND J30-B 4 -B10 CN18-B 5 SD13_CONT CN57-B14 SD13_CONT
CN32-B 7 SGND J20- 8 -3 -2
CN188- 2 SIG J30-B 5 -B 9 CN18-B 4 SD12_CONT CN57-B15 SD12_CONT CN81-B 7 SD13_24V CN146- 1 24V SC pressure arm solenoid
Cover paper table upper limit sensor /Rr PS27 CN32-B 8 PS27_SIG J20- 7 -4 -1 SD13
CN188- 1 5V J30-B 6 -B 8 CN18-B 3 SD11_CONT CN57-B16 SD11_CONT CN81-B 8 SD13_DRV CN146- 2 DRV
CN32-B 9 5V
J30-B 9 -B 5 CN18-B 2 SD4_CONT CN57-B17 SD4_CONT
CN160- 3 S.GND CN32-B10 LED21_CONT CN18-B 1 SD3_CONT CN57-B18 SD3_CONT
7
7
8
8
CN162- 3 S.GND CN33- 10 LED32_CONT CN17-A 2 M46_MODE1 CN56-A17 M46_MODE1 CN114- 2 COM
5
Pellet count LED LED32 CN162- 2 NC CN17-A 1 M46_CLK CN56-A18 M46_CLK CN114- 5 COM
J41- 9 -10
6
9
9
10
10
CN19-A 9 M23_CONT CN58-A 9 M23_CONT CN83- 16 M34_DRV1 CN117- 1 DRV1 Pellet supply arm motor
J41-17 -2 -1 M34
CN19-A 8 M22_F/R CN58-A10 M23_F/R CN83- 17 M34_DRV2 CN117- 2 DRV2
Glue tank
11
11
Yellow-5 CN166-2 J53-5 -5 J90-A15 -A 5 CN19-B 7 M50_F/R CN58-B11 M50_F/R CN75- 6 M46_DRV_B/ CN123- 1 B/
CN242- * NO CN35-A15 SW42 CN19-B 6 M50_CONT CN58-B12 M50_CONT
Cutter end position switch
SW42 Brown-6 CN166-1 J53-6 -4 J90-A16 -A 4 CN19-B 5 M49_F/R CN58-B13 M49_F/R CN75- 7 M47_24V CN124- 5 COM
(Within the cutter unit) CN242- * COM CN35-A16 SGND CN19-B 4 M49_CONT CN58-B14 M49_CONT CN75- 8 M47_24V CN124- 2 COM
CN19-B 3 M48_F/R CN58-B15 M48_F/R CN75- 9 M47_DRV_A CN124- 4 A
CN201- 3 S.GND J53-7 -3 J90-A17 -A 3 CN19-B 2 SOUT10 CN58-B16 SOUT10 M47 Cover paper table up down motor /Rr
CN35-A17 SGND CN75- 10 M47_DRV_A/ CN124- 6 A/
CN201- 2 SIG J53-8 -2 J90-A18 -A 2 CN19-B 1 SOUT9 CN58-B17 SOUT9
Cover paper switchback switch PS44 CN35-A18 PS44_SIG CN75- 11 M47_DRV_B CN124- 3 B
CN201- 1 5V J53-9 -1 J90-A19 -A 1
CN35-A19 5V CN75- 12 M47_DRV_B/ CN124- 1 B/
12
12
13
13
CN218- 1 5V CN36-A 3 5V
14
14
-2
CN36-A17 PS60_SIG CN 7-A15 NSW4-1
-1
CN36-A18 5V CN 7-A14 NSW3-8 J91- 4 -6 J53-9 -1 CN166-6 -1Red Cutter motor
CN84- 5 M50_DRV1 CN127- * DRV1
CN 7-A13 NSW3-4 J91- 3 -7 J53-8 -2 CN166-5 -2Black M50
CN217- 3 SIG CN36-A19 PS65_SIG CN84- 6 M50_DRV2 CN127- * DRV2 (Within the cutter unit)
CN 7-A12 NSW3-2
Booklet load limit sensor PS65 CN217- 2 NC
CN 7-A11 NSW3-1 J91- 2 -8 -2
CN217- 1 SGND CN36-A20 SGND CN84- 7 SD41_24V CN150- 1 24V
CN 7-A10 NSW2-8 J91- 1 -9 -1 SD41 Cutter HP sensor
CN 7-A 9 NSW2-4 CN84- 8 SD41_DRV CN150- 2 DRV
CN 7-A 8 NSW2-2 CN84- 9 SD42_24V
CN213- 3 S.GND J61- 7 -9
CN36-B 1 SGND CN 7-A 7 NSW2-1 CN84- 10 SD42_DRV
CN213- 2 SIG J61- 8 -8
Booklet end sensor PS61 CN36-B 2 PS61_SIG CN 7-A 6 NSW1-8 CN84- 11 SD43_24V
CN213- 1 5V J61- 9 -7
CN36-B 3 5V CN 7-A 5 NSW1-4 CN84- 12 SD43_DRV
CN214- 3 S.GND J61-10 -6
Booklet conveyance belt CN36-B 4 SGND CN 7-A 4 NSW1-2
CN214- 2 SIG J61-11 -5
PS62 CN36-B 5 PS62_SIG CN 7-A 3 NSW1-1
movement HP sensor CN214- 1 5V J61-12 -4 CN78- 1 NC
CN36-B 6 5V CN 7-A 2 5V
CN78- 2 M61_24V CN129- 3 COM
CN 7-A 1 5V
CN216- 3 S.GND J65- 1 -3 J61-13 -3 CN78- 3 M61_24V CN129- 9 COM
CN36-B 7 SGND CN 7-B20 SGND
CN216- 2 SIG J65- 2 -2 J61-14 -2 CN78- 4 M61_DRV_A CN129- 1 A Booklet conveyance belt motor
CN36-B 8 PS64_SIG CN 7-B19 SGND
Booklet
Booklet conveyance belt lower limit sensor PS64 J65- 3 -1 J61-15 -1 CN78- 5 M61_DRV_A/ M61
CN216- 1 5V CN129- 5 A/
CN36-B 9 5V CN 7-B18 NC
CN78- 6 M61_DRV_B CN129- 7 B
CN 7-B17 NC
15
15
16
16
17
17
CN38- 5 NC
CN10-A 6 NSW1-8 J70- 2 -1 -2
CN10-A 5 NSW1-4 CN86- 12 NC CN152- 1 24V Cover paper tray solenoid
J70- 1 -2 -1 SD72
J75- 1 -3 CN10-A 4 NSW1-2 CN86- 13 NC CN152- 2 DRV
CN247- 1 SIG㧗 CN39- 1 PCB72_IN㧗
CN247- 2 SIG- J75- 2 -2 CN10-A 3 NSW1-1 CN86- 14 RSV_SD2_24V
Multi feed detection board /2 MFDTB72 CN39- 2 PCB72_IN-
CN247- 3 GND J75- 3 -1 CN10-A 2 5V CN86- 15 RSV_SD2_DRV
CN39- 3 AGND
CN10-A 1 5V CN261- 1 SD72_24V
CN10-B20 SGND CN261- 2 SD72_DRV
Cover paper feed/
CN10-B19 SGND
J73-15 -15
CN10-B18 NC CN87-A 1 24V1
J73-21 -21
CN10-B17 NC CN87-A 2 PGND
CN10-B16 NC CN87-A 3 NC
CN370 - 6 5V J5-1 -12 CN10-B15 NC CN87-A 4 NC
J73-14 -14
CN370 - 5 LED1 -2 -11 CN10-B14 NC CN87-A 5 5V
J73-12 -12
CN370 - 4 LED2 -3 -10 CN10-B13 NC CN87-A 6 TRAY_SET
J73- 9 -9
CN370 - 3 LED3 -4 -9 CN10-B12 NLED7 CN87-A 7 M71_LD
J73-10 -10
CN370 - 2 LED4 -5 -8 CN10-B11 NLED6 CN87-A 8 M72_LD
J57- 1 -18 J73- 1 -1
CN370 - 1 NC -6 -7 CN4- 1 5V CN10-B10 NLED5 CN87-A 9 M73_DRV1 CN136- 1 DRV1 Cover paper tray lift motor
J57- 2 -17 J73-13 -13 M73
CN4- 2 JAM_OUT1 CN10-B 9 NLED4 CN87-A10 M73_DRV2 CN136- 2 DRV2
J57- 3 -16 CN10-B 8 NLED3
19
19
CN4- 3 JAM_OUT2
JAMB/1
CN11- 6 SGND CN87-B 3 PS76_SIG CN225- 2 SIG PS76 Cover paper conveyance sensor /2
CN11- 7 TXD1_IN CN225- 1 5V
CN11- 8 5V
J84-3 -1
CN11- 9 5V CN226- 3 SGND
20
20
CN231- 3 SGND
J73- 4 -4 Cover paper tray knob sensor
CN87-B 5 PS82_SIG CN231- 2 SIG PS82
CN48- 4 5V J6-1 -11 CN5- 1 5V CN231- 1 5V
CN48- 3 MAN_SW1 -2 -10 CN5- 2 SW_1
Cover paper feed
-3 -9 J80-3 -4
CN48- 2 MAN_LED1 CN5- 3 LED_1 CN223- 3 SGND
Cover paper tray
CN134- 3 PGND
CN13-A16 NSW4-2
CN13-A15 NSW4-1
CN13-A14 NSW3-8 J82-3 -1 -3
CN13-A13 NSW3-4 J82-2 -2 -2 CN135- 1 DRV
CN13-A12 NSW3-2 J82-1 -3 -1 CN135- 2 EM M72 Cover paper tray fan /2
CN13-A11 NSW3-1 CN135- 3 PGND
WIT
BLK
CN49- 2 MAN_LED4
CN49- 1 NC CN23-4 RTS CN13-B17 NC
CN23-5 CTS CN13-B16 NC
CN13-B15 NC CN89- 1 M91_24V
AC CODE
CN239-1A BLK
CN237-2 SG
FT5
FT6
J8-4
J8-3
J8-1
J8-2
CN88- 5 PS92_SIG
CN24-8 NC CN14- 1 /RES_CONT
CN88- 6 5V
CN236-1 PAPER_OUT CN14- 2 FWE_CNT1
CN88- 7 SGND
CN236-2 SG CN14- 3 MD2
CN88- 8 RSV_PS2_SIG
WIT
WIT
BLK
BLK
CN88- 9 5V
CN236-4 5V CN14- 5 TXD1_OUT
CN88- 10 SGND
CN236-5 5V CN14- 6 SGND
J7-4
J7-3
J7-1
J7-2
FNS
CN88- 11 AD_SUB1
FT9
Circuit breaker
CN14- 7 TXD1_IN
FT10
CN88- 12 5V
CN14- 8 5V
CN235-1 24V CN14- 9 5V
J7-4
J7-3
J7-1
J7-2
CN235-2 5V
CN235-3 SG
CN235-4 PG
CN235-5 PG
BLK FT11
WIT FT12
WIT J2-4
CN52-3 24V2 CN98-4 㧗V/24V CN66-5 :LINE(N)
-1
-2
-3
-6
-5
-4
-3
-2
NF1
CN98-2 -V/PGND
24
24
FT13
FT14
CN29-1 NC
-4
-3
-2
-1
-6
-5
-4
-3
-2
-1
(with interlock)
CN93-1 PS_ON
CN29-2 NC
CN28-2 CN93-2 PGND
CN29-3 FNS2_RTS
CN28-1
CN29-4 FNS2_SIN
WIT
BLK
WIT
BLK
CN27-1 MTXD
CN 2-1 SYS_SIN
CN27-2 SG
13
CN 2-2 S.GND
CN47-1B
CN47-2B
CN 2-3 /SYS_RTS
19
CN97-3 -V/PGND
CN 2-6 /SYS_CTS
CN51-4 PGND CN97-2 -V/PGND
CN 2-7 /PAPEROUT_1 CN67-1 :LINE(H) BLK
CN97-1 -V/PGND
20
CN47-1A
CN47-2A
Front door switch
14
CN26-1 PAPER_OUT
DCPU/1
CN26-2 SG
CN92-1 PS_ON
15
15
CN26-3 SG CN44- 1 5V
25
25
CN92-2 PGND
(without interlock)
16
CN 1- 1 5V
16
CN26-4 5V CN44- 2 5V
17
CN 1- 2 NC
17
CN 1- 3 SGND
18
CN44- 4 SGND
CN25-1 24V
CN25-2 5V
WIT
BLK
CN25-3 SG
CN25-4 PG
Crimp
CN25-5 PG CN95-1
11
㧦㧗V/5V
CN25-6 FG WIT
Main body
CN50- 2 5V 㧦㧗V/5V
11
CN42- 1 5V
CN50- 3 SGND CN95-3
BLK
12
CN95-4
12
CN42- 4 24V1
14
CN42- 5 PGND
MS3
CN248-1A
CN248-2A
26
26
CN43- 1 RL_CONT
2
BLK
CN45- 1 AC_H(5V)
BLK
CN45- 2 AC_H(24V1)
BLK BLK J2-1
CN45- 3 AC_H(24V2)
WIT
CN45- 4 AC_N(5V)
Connector Faston
WIT
Relay cnnector
CN45- 5 AC_N(24V1)
ACDB
J44- 5 -5
J44- 6 -6
I
Z
T
F
Y
X
V
S
P
K
E
B
A
U
R
N
H
D
C
Q
O
G
W
Field Service Ver3.0 Nov.2006 19. PAPER SETTING
1050e/1050eP
NOTE
• This table lists the optimum setting values by paper brands checked for paper through by Konica Minolta. For other brands, it is scheduled that information is provided in due course upon completion of the paper through check.
Weight 40 to 49 g/m2 50 to 61 g/m2 62 to 71 g/m2 72 to 91 g/m2 92 to 130 g/m2 131 to 161 g/m2 162 to 209 g/m2 210 to 244 g/m2 245 to 300 g/m2
Paper type Tray/4
2
Coated A Futura Leser (105 g/m )
(Smoothness: over100sec)
Line speed (mm/s) 290 290 425 490 490 490 490 490 425
Fusing temp. index (°C) -15 -15 -15 -10 Standard temp. +5 +5 +5 +5
Coated B
(Smoothness: over100sec)
Line speed (mm/s) 290 290 425 490 490 490 490 490 425
Fusing temp. index (°C) -15 -15 -15 -10 Standard temp. +5 +5 +5 +5
Fine Domtar (16 lb, 60 g/m2) Gilbert Neutech Color (28lb, 105 Kromekote Cover Leser High
(Smoothness: 50 to 100sec) g/m2) Gross (183 g/m2)
HM Color (28lb, 105 g/m2) Domter Color (65lb,176 g/m2)
Cover Supersmooth (65lb,176g/
m2)
Line speed (mm/s) 290 425 490 490 490 490 490 425 290
Fusing temp index. (°C) -15 -15 -15 -10 Standard temp. +5 +5 +5 +5
Normal Docupaque (16 lb, 60 g/m2) HM-T MP (20lb, 75g/m2) Cougar Opaque Digital Smooth
(Smoothness: 20 to 50sec) HM-Fore (20lb, 75g/m2) Cover 65lb 7885 (176g/m2)
Wheyerhauser Recycled Laser
(20lb, 75g/m2)
Domter (20lb,75g/m2)
Great White (20lb,75g/m2)
Great White Rycycle Content
(20lb,75g/m2)
Xerox4024 (20lb,75g/m2)
Husky Xerocopy (20lb,75g/m2)
Recycle Eclips 20lb (20lb,75g/m2)
AVERY 5160
Line speed (mm/s) 490 490 490 490 490 490 425 290 290
1. Line speed and fusing temperature are decided by setting the paper type and paper weight.
2. Smoothness is a value measured by the Beck smoothness testing machine stipulated in the ISO 5627:1995, and the smaller the value, the coarser the paper grain. When the paper is not listed in this table and the setting condition of which can not be found, obtain the smoothness data from the paper manufacturer and select the type of paper according to the value
of smoothness.
3. Coated paper B: To be used when it is corresponding to overlay printing. For particulars, see chapter III "6.5 Overlay printing adjustment" in the Field Service.
No halftone dot: Air auto Frame in a thin line: No paper feed assist plate used
NOTE
• When using high quality printing paper, be sure to select a setting direction in which there occurs less amount of curling after printing.
• Marked with *: Paper the classification of which of smoothness or weight has been changed from the viewpoint of performance.
19. PAPER SETTING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
19.2 Relationship between the optimum value and the control of each of setting items by paper brand (U.S.A. paper) (for fusing soft roller)
NOTE
/1050e/1050eP
• This table lists the optimum setting values by paper brands checked for paper through by Konica Minolta. For other brands, it is scheduled that information is provided in due course upon completion of the paper through check.
Weight 40 to 49 g/m2 50 to 61 g/m2 62 to 71 g/m2 72 to 91 g/m2 92 to 130 g/m2 131 to 161 g/m2 162 to 209 g/m2 210 to 244 g/m2 245 to 300 g/m2
Paper type Tray/4
Coated A Futura Leser (105 g/m2)
(Smoothness: over 100sec)
Line speed (mm/s) 290 290 425 490 490 490 (425 when paper width is less 290 290 290
than 8.5-inch)
Fusing temp index. (°C) -20 Standard temp. Standard temp. Standard temp. +15 +15 +15 +15 +15
Coated B
(Smoothness: over 100 sec)
Line speed (mm/s) 290 290 425 490 490 490 (425 when paper width is less 290 290 290
than 8.5-inch)
Fusing temp. index (°C) -20 Standard temp. Standard temp. Standard temp. +15 +15 +15 +15 +15
Fine Domtar (16 lb, 60 g/m2) GilbertNeutechColor (28lb, 105g/ Kromekote Cover Leser High
(Smoothness: 50 to 100 sec) m 2) Gross (183g/m2)
HM Color (28lb, 105g/m2) Domter Color (65lb,176g/m2)
Cover Supersmooth (65lb,176g/
m 2)
Line speed (mm/s) 290 425 490 490 490 425 290 290 290
Fusing temp. index (°C) -10 Standard temp. +5 +10 +15 +15 +15 +15 +15
Normal Docupaque (16 lb, 60) HM-T MP (20lb, 75g/m2) Cougar Opaque Digital Smooth
(Smoothness: 20 to 50sec) HM-Fore (20lb, 75g/m2) Cover 65lb 7885(176g/m2)
Wheyerhauser Recycled Laser
(20lb, 75g/m2)
Domter (20lb,75g/m2)
Great White (20lb,75g/m2)
Great White Rycycle Content
(20lb,75g/m2)
Xerox 4024 (20lb,75g/m2)
Husky Xerocopy (20lb,75g/m2)
Recycle Eclips 20lb (20lb,75g/m2)
AVERY 5160
Line speed (mm/s) 490 490 490 490 490 425 290 290 290
Fusing temp. index (°C) Standard temp. Standard temp. +10 +15 +15 +15 +15 +15 +15
Book/News Cougar Cover (65lb, 176g/m2)
(Smoothness: 10 to 20 sec) Disable Digital Laser Opaque Couverture Disable
Cover (65lb, 176g/m2) * (A fusing performance is not securable.)
1. Line speed and fusing temperature are decided by setting the paper type and paper weight.
2. Smoothness is a value measured by the Beck smoothness testing machine stipulated in the ISO 5627:1995, and the smaller the value, the coarser the paper grain. When the paper is not listed in this table and the setting condition of which can not be found, obtain the smoothness data from the paper manufacturer and select the type of paper according to the value
of smoothness.
3. Coated paper B: To be used when it is corresponding to overlay printing. For particulars, see chapter III "6.5 Overlay printing adjustment" in the Field Service.
No halftone dot: Air auto Frame in a thin line: No paper feed assist plate used
NOTE
• When using high quality printing paper, be sure to select a setting direction in which there occurs less amount of curling after printing.
• Marked with *: Paper the classification of which of smoothness or weight has been changed from the viewpoint of performance.
Field Service Ver3.0 Nov.2006 19. PAPER SETTING
1050e/1050eP
• This table lists the optimum setting values by paper brands checked for paper through by Konica Minolta. For other brands, it is scheduled that information is provided in due course upon completion of the paper through check.
Weight 40 to 49 g/m2 50 to 61 g/m2 62 to 71 g/m2 72 to 91 g/m2 92 to 130 g/m2 131 to 161 g/m2 162 to 209 g/m2 210 to 244 g/m2 245 to 300 g/m2
Paper type Tray/4
Coated A PRIMASET115 (115g/m2) RDEREY (160g/m2) RDEREY (200g/m2)
(Smoothness: over 100sec) Schneidersohne Business Paper
Color Copy (120g/m2)
Line speed (mm/s) 290 290 425 490 490 490 490 490 425
Fusing temp. index (°C) -15 -15 -15 -10 Standard temp. +5 +5 +5 +5
Coated B
(Smoothness: over 100sec)
Line speed (mm/s) 290 290 425 490 490 490 490 490 425
Fusing temp. index (°C) -15 -15 -15. -10 Standard temp. +5 +5 +5 +5
Fine Clair Mail (60g/m2) Mondi Business Paper Color
(Smoothness: 50 to 100sec) Copy (200g/m2)
(NEU Color Copy (200g/m2))
PRIMASET (170g/m2)
Line speed (mm/s) 290 425 490 490 490 490 490 425 290
Fusing temp. index (°C) -15 -15 -15 -10 Standard temp. +5 +5 +5 +5
Normal Mondi CEETEE COPIER (60g/m2) Konicaminolta Profi (80g/m2)* Nautilaus (80g/m2) Plano Jet90 (90g/m2)
(Smoothness: 20 to 50sec) (NEU CEETEE COPIER (60g/m2)) NOPA Top (80g/m2)
Konicaminolta Original (80g/m2)
Konica Minolta Color + A4 (90g/
m2)
(NEU Color Copy (90g/m2))
REPEAT (80g/m2)
Turbocopy80 (80g/m2)
Turbocopy80 (SB,BB) (80g/m2)
AVERY DSP24
Line speed (mm/s) 490 490 490 490 490 490 425 290 290
Fusing temp. index (°C) -5 -5 -5 Standard temp. +5 +5 +5 +5 +5
Book/News BioTop3 (80g/m2) Xerox3R91978 (160g/m2) Turbocopy (160g/m2)*
(Smoothness: 10 to 20sec) Classic White (80g/m2)
Line speed (mm/s) 490 490 490 425 425 290 290 290
Fusing temp. index (°C) Standard temp. Standard temp. Standard temp. +5 +5 +5 +5 +10
Disable
Embossed
(Smoothness: 5 to 10sec) Disable
(A fusing performance is not securable.)
Line speed (mm/s) 490 490 425 290 290 290
Fusing temp. index (°C) Standard temp. +5 +5 +5 +10 +10
1. Line speed and fusing temperature are decided by setting the paper type and paper weight.
2. Smoothness is a value measured by the Beck smoothness testing machine stipulated in the ISO 5627:1995, and the smaller the value, the coarser the paper grain. When the paper is not listed in this table and the setting condition of which can not be found, obtain the smoothness data from the paper manufacturer and select the type of paper according to the value
of smoothness.
3. Coated paper B: To be used when it is corresponding to overlay printing. For particulars, see chapter III "6.5 Overlay printing adjustment" in the Field Service.
No halftone dot: Air auto Frame in a thin line: No paper feed assist plate used
NOTE
• When using high quality printing paper, be sure to select a setting direction in which there occurs less amount of curling after printing.
• Marked with *: Paper the classification of which of smoothness or weight has been changed from the viewpoint of performance.
19. PAPER SETTING Field Service Ver3.0 Nov.2006
bizhub PRO 1050/1050P
19.4 Relationship between the optimum value and the control of each of setting items by paper brand (European paper) (for fusing soft roller)
NOTE
/1050e/1050eP
• This table lists the optimum setting values by paper brands checked for paper through by Konica Minolta. For other brands, it is scheduled that information is provided in due course upon completion of the paper through check.
Weight 40 to 49 g/m2 50 to 61 g/m2 62 to 71 g/m2 72 to 91 g/m2 92 to 130 g/m2 131 to 161 g/m2 162 to 209 g/m2 210 to 244 g/m2 245 to 300 g/m2
Paper type Tray/4
Coated A PRIMASET115 (115g/m2) RDEREY (160g/m2) RDEREY (200g/m2)
(Smoothness: over100sec) Schneidersohne Business Paper
Color Copy (120g/m2)
Line speed (mm/s) 290 290 425 490 490 490 (425 when paper width is 290 290 290
215mm or less)
Fusing temp. index (°C) -20 Standard temp. Standard temp. Standard temp. +15 +15 +15 +15 +15
Coated B
(Smoothness: over 100sec)
Line speed (mm/s) 290 290 425 490 490 490 (425 when paper width is 290 290 290
215mm or less)
Fusing temp. index (°C) -20 Standard temp. Standard temp. Standard temp. +15 +15 +15 +15 +15
2
Fine Clair Mail (60g/m ) Mondi Business Paper Color Mondi Business Paper Color
(Smoothness: 50 to 100sec) Copy(100g/m2)* Copy (200g/m2)
(NEU Color Copy (200g/m2))
PRIMASET (170g/m2)
Line speed (mm/s) 290 425 490 490 490 425 290 290 290
Fusing temp. index (°C) -10 Standard temp. +5 +10 +15 +15 +15 +15 +15
Normal Mondi CEETEE COPIER (60g/m2) Konicaminolta Profi (80g/m2)* Nautilaus (80g/m2) PlanoJet90 (90g/m2)
(Smoothness: 20 to 50sec) (NEU CEETEE COPIER (60g/m2)) NOPA Top (80g/m2)
Konicaminolta Original (80g/m2)
Konica Minolta Color + A4 (90g/
m2)
(NEU Color Copy (90g/m2))
REPEAT (80g/m2)
Turbocopy80 (80g/m2)
Turbocopy80 (SB,BB) (80g/m2)
AVERY DSP24
Line speed (mm/s) 490 490 490 490 490 425 290 290 290
Fusing temp. index (°C) Standard temp. Standard temp. +10 +15 +15 +15 +15 +15 +15
Book/News BioTop3 (80g/m2) Xerox3R91978 (160g/m2) Turbocopy (160g/m2)*
(Smoothness: 10 to 20sec) Classic White (80g/m2)
1. Line speed and fusing temperature are decided by setting the paper type and paper weight.
2. Smoothness is a value measured by the Beck smoothness testing machine stipulated in the ISO 5627:1995, and the smaller the value, the coarser the paper grain. When the paper is not listed in this table and the setting condition of which can not be found, obtain the smoothness data from the paper manufacturer and select the type of paper according to the value
of smoothness.
3. Coated paper B: To be used when it is corresponding to overlay printing. For particulars, see chapter III "6.5 Overlay printing adjustment" in the Field Service.
No halftone dot: Air auto Frame in a thin line: No paper feed assist plate used
NOTE
• When using high quality printing paper, be sure to select a setting direction in which there occurs less amount of curling after printing.
• Marked with *: Paper the classification of which of smoothness or weight has been changed from the viewpoint of performance.
Field Service Ver3.0 Nov.2006 19. PAPER SETTING
1050e/1050eP
• Paper weight (g/m2):Unit showing the mass of a 1 m2 sheet of paper in gram.
• Basis Weight (lb): The basis weight of a paper is the designated fixed weight of 500 sheets, measured in pounds, in that paper's basic sheet size.
It is important to note that the "basic size" is not the same for all types of paper.
Paper type Basic size Bond Cover Index Bristol Tag Book
(inch) 17 x 22 20 x 26 25.5 x 30.5 22.5 x 28.5 24 x 36 25 x 38
(mm) 432 x 559 508 x 660 648 x 775 572 x 724 610 x 914 635 x 965
g/m2 lb lb lb lb lb lb
40.0 10.7 14.8 22.2 18.3 24.6 27.1
50.0 13.3 18.5 27.7 22.8 30.8 33.8
52.3 13.9 19.4 29.0 23.9 32.2 35.4
54.2 14.4 20.1 30.0 24.7 33.3 36.7
60.2 16.0 22.3 33.3 27.5 37.0 40.7
64.0 17.0 23.7 35.4 29.2 39.4 43.3
66.3 17.7 24.6 36.7 30.3 40.8 44.9
68.7 18.3 25.4 38.0 31.4 42.3 46.5
72.3 19.3 26.8 40.0 33.0 44.5 48.9
75.9 20.2 28.1 42.0 34.7 46.7 51.3
80.0 21.3 29.6 44.3 36.5 49.2 54.1
83.7 22.3 31.0 46.4 38.2 51.5 56.6
88.0 23.4 32.6 48.7 40.2 54.1 59.5
90.0 24.0 33.3 49.8 41.1 55.4 60.9
98.3 26.2 36.4 54.4 44.9 60.5 66.5
100.0 26.6 37.0 55.4 45.7 61.5 67.6
104.7 27.9 38.8 58.0 47.8 64.4 70.8
108.0 28.8 40.0 59.8 49.3 66.4 73.1
110.0 29.3 40.7 60.9 50.2 67.7 74.4
120.0 32.0 44.4 66.5 54.8 73.8 81.2
127.9 34.1 47.4 70.8 58.4 78.7 86.5
130.0 34.6 48.1 72.0 59.4 80.0 87.9
140.0 37.3 51.8 77.5 63.9 86.1 94.7
150.0 39.9 55.5 83.1 68.5 92.3 101.5
160.0 42.6 59.2 88.6 73.1 98.4 108.2
170.0 45.3 62.9 94.2 77.6 104.6 115.0
180.0 47.9 66.7 99.7 82.2 110.7 121.8
190.0 50.6 70.4 105.2 86.8 116.9 128.5
200.0 53.3 74.1 110.8 91.3 123.1 135.3
210.0 55.9 77.8 116.3 95.9 129.2 142.1
220.0 58.6 81.5 121.8 100.5 135.4 148.8
230.0 61.3 85.2 127.4 105.0 141.5 155.6
240.0 63.9 88.9 132.9 109.6 147.7 162.4
250.0 66.6 92.6 138.5 114.2 153.8 169.1
260.0 69.2 96.3 144.0 118.7 160.0 175.9
270.0 71.9 100.0 149.5 123.3 166.1 182.7
280.0 74.6 103.7 155.1 127.9 172.3 189.4
290.0 77.2 107.4 160.6 132.4 178.4 196.2
300.0 79.9 111.1 166.2 137.0 184.6 203.0
Divisor 3.7548 2.7006 1.8056 2.1899 1.6253 1.4782