Professional Documents
Culture Documents
Designation:
new old
“Hydrocontrol VTR” “Hydrocontrol R”
Function:
Oventrop double regulating and commissioning valves are instal-
led in the pipework of hot water central heating and cooling
systems and serve to achieve a hydronic balance between the
various circuits of the system.
The balance is achieved by a presetting with memory position.
The required values of presetting can be obtained from the flow
charts. All intermediate values are infinitely adjustable.
The selected presetting can be read off two scales (basic scale
and fine adjustment scale, see illustration presetting). The Oven-
trop double regulating and commissioning valves have 2 threaded
ports for fill and drain ball valves or pressure test points for the Bronze double regulating and commissioning valve PN 16/PN 25
measurement of differential pressure. “Hydrocontrol VTR”
The double regulating and commissioning valves may be installed
in either the supply or the return pipe.
When installing the valve it must be ensured that the direction of
flow conforms to the direction of the arrow on the valve body and
that the valve is installed with a minimum of L = 3 x Ø of straight
pipe at the valve inlet and of L = 2 x Ø of straight pipe at the valve
outlet.
The flow charts are valid for both, installation in the supply or the
return pipe, provided the direction of flow conforms to the arrow
embossed on the valve body.
In cooling systems using mixtures of water and glycol, the cor-
rection factors related to the indicated chart values have to be
taken into consideration.
Advantages:
– the location of the functioning components on one level allows both ports male thread
a simple assembly and easy operation for weldable steel tailpipes
– only one valve for 5 functions: DN 10 up to DN 50
presetting
or:
measuring
... for solder tailpipes 15 mm up to 54 mm
isolating
filling or:
draining ... for threaded tailpipes DN 10 up to DN 50
– the supply and the return pipe can be marked by use of the
or:
colour rings supplied with each valve
…for female threaded tailpipes DN 15 up to DN 32
– low pressure loss (oblique pattern)
– infinitely adjustable presetting, exact measurement of pressure
loss and flow via the pressure test points
– threads according to EN 10226 (BS 21), suitable for Oventrop
compression fittings (102 71 51-58) for copper pipes up to a
max. diameter of 22 mm and Oventrop composition pipe
“Copipe”
– fill and drain ball valve with internal stop and pressure test point
with O-ring seal between valve body and test point (no addi-
tional seals required)
– patented measuring channel led around the stem assembly to
the test points ensures the best possible accuracy between the
differential pressure measured at the pressure test points and
the actual differential pressure of the valve (see chart indicating
flow rate tolerances)
both ports female thread according to EN 10226 (BS 21)
DN 10 to DN 65
2011 Oventrop 1
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
Tender specification:
0
2
Double regulating and commissioning valve PN 25 (water pH value 4
6
0
6.5-10) (DN 65: PN 16), both ports with female thread according to 2
4
6
EN 10226 (BS 21), not suitable for steam. Colour rings for marking 0
of supply and return pipe (except for DN 65), oblique pattern with
secured, infinitely adjustable fine presetting controllable at any ti-
me; optical display of the presetting depending on the position of
the handwheel, valve body and bonnet made of bronze (Rg 5), disc
and stem made of brass resistant to de-zincification (DZR), disc both ports female thread according to EN 10226 (BS 21),
with PTFE seal, maintenance-free stem seal due to double O-ring, item no. 106 01..
all functioning components on one level, pressure test point and fill
and drain ball valve interchangeable, installation in the supply or
the return pipe. DN 15 up to DN 32 DVGW tested and registered,
DN 10 up to DN 50 WRAS tested and registered.
DN 10 to DN 50 with type approval certificate for shipbuilding.
(Pressure loss charts, kv and Zeta values, see following pages)
0
Max. operating temperature ts: +150 °C 2
4
6
DN 65 21⁄2" 106 01 20
1
0
DN 15 ⁄2" 106 03 04 2
4
6
0
3
DN 20 ⁄4" 106 03 06
DN 25 1" 106 03 08 Pressure test
point
DN 32 11⁄4" 106 03 10 Fill + drain ball valve
DN 40 11⁄2" 106 03 12 Measuring adapter
DN 50 2" 106 03 16
D
DN EN 10226 t L H
2 2011 Oventrop
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
DN 15 2.88 15 mm 106 01 51
DN 15 3.88 18 mm 106 01 52
DN 20 5.71 22 mm 106 01 54
D
DN 25 8.89 25 mm 106 01 56
DN 32 19.45 35 mm 106 01 58
DN 40 27.51 42 mm 106 01 60
DN 50 38.78 54 mm 106 01 62 SW
For the direct connection of copper pipes according to EN
1057/DVGW GW 392, stainless steel pipes according to EN
10088/DVGW 541 and thin-walled C-steel pipes (material no. E
H
195/1.0034) according to EN 10305-3. Pressing must be carried
out to tighten the connection. Only use press jaws with the original
contours SANHA (SA), Geberit-Mapress (MM) or Viega (Profipress).
Pressure test point
Processing must be carried out according to the installation
instructions. Fill+drain ball valve
components on one level, pressure test point and fill and drain ball
valve interchangeable, installation in the supply or the return pipe.
DN 15 to DN 32 DVGW tested and registered.
0
DN 10 to DN 50 with type approval certificate for shipbuilding. 2
4
6
H
0
(Pressure loss charts, kv and Zeta values, see following pages) 2
4
6
0
2011 Oventrop 3
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
D3
D4
D1
32 35 32 25 R 1 ⁄4 1
46 19.1 41 60 Rp 1 ⁄4 1
55 19.1 2 tailpipes with male thread
R 3⁄8 for valve DN 10 106 14 91
40 42 37 29 R 11⁄2 49 19.1 47.5 65 – – – R 1⁄2 for valve DN 15 106 14 92
R 3⁄4 for valve DN 20 106 14 93
50 54 50 40 R 2 55 23.4 60 65 – – – R 1 for valve DN 25 106 14 94
R 11⁄4 for valve DN 32 106 14 95
R 11⁄2 for valve DN 40 106 14 96
R 2 for valve DN 50 106 14 97
DN 10
Presetting * *
Zeta-value
Zeta-value
Zeta-value
Pressure loss Δp [kPa]
Pressure loss Δp [mbar]
kv-value
kv-value
kv-value
Turn
Turn
4. 1.76 13
4.1 1.82 12
Flow rate qm [l/s] 4.2 1.88 11
4.3 1.94 10
4.4 2.00 9.8
4.5 2.06 9.2
4.6 2.12 8.7
* Avoid presetting < 1, see tolerance curve page 9. 4.7 2.19 8.1
4.8 2.25 7.7
4.9 2.31 7.3
4 2011 Oventrop
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
DN 15
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Presetting * *
Turn
Turn
Turn
0.25 0.23 1981
0.5 0.34 906
0.75 0.40 655
1. 0.46 495 5. 2.70 14
1.1 0.48 455 5.1 2.77 14
1.2 0.50 419 5.2 2.84 13
1.3 0.52 388 5.3 2.92 12
1.4 0.55 346 5.4 2.99 12
1.5 0.57 323 5.5 3.06 11
1.6 0.60 291 5.6 3.13 11
1.7 0.63 264 5.7 3.20 10
1.8 0.66 241 5.8 3.27 9.8
1.9 0.69 220 5.9 3.34 9.4
3. 1.34 58 7. 3.88 7
3.1 1.41 53
3.2 1.48 48
3.3 1.55 44
3.4 1.62 40
3.5 1.70 36
3.6 1.77 33
3.7 1.84 31
3.8 1.91 29
3.9 1.98 27
4. 2.05 25
4.1 2.12 23
4.2 2.18 22
4.3 2.24 21
4.4 2.31 20
Flow rate qm [l/s] 4.5 2.38 18
4.6 2.44 18
4.7 2.51 17
4.8 2.57 16
* Avoid presetting < 1, see tolerance curve page 9. 4.9 2.63 15
DN 20
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Turn
Turn
Turn
Presetting * *
Pressure loss Δp [kPa]
Pressure loss Δp [mbar]
4. 2.58 52
4.1 2.69 48
4.2 2.80 44
4.3 2.91 41
4.4 3.01 38
4.5 3.12 36
4.6 3.23 33
Flow rate qm [l/s] 4.7 3.34 31
4.8 3.44 29
4.9 3.55 28
2011 Oventrop 5
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
DN 25
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Presetting * *
Turn
Turn
Turn
Pressure loss Δp [kPa]
Pressure loss Δp [mbar]
3. 3.69 66 7. 8.89 11
3.1 3.82 62
3.2 3.96 57
3.3 4.11 53
3.4 4.26 50
3.5 4.42 46
3.6 4.57 43
3.7 4.72 40
3.8 4.87 38
3.9 5.02 36
4. 5.16 34
4.1 5.32 32
4.2 5.47 30
4.3 5.63 28
4.4 5.79 27
4.5 5.95 25
4.6 6.10 24
4.7 6.26 23
Flow rate qm [l/s] 4.8 6.42 22
4.9 6.57 21
DN 32
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Turn
Turn
Turn
Presetting * *
Pressure loss Δp [mbar]
3. 6.00 74 7. 13.91 14
3.1 6.17 70 7.1 14.13 13
3.2 6.35 66 7.2 14.35 13
3.3 6.52 62 7.3 14.57 13
3.4 6.70 59 7.4 14.80 12
3.5 6.85 57 7.5 15.02 12
3.6 7.00 54 7.6 15.24 11
3.7 7.16 52 7.7 15.46 11
3.8 7.33 49 7.8 15.68 11
3.9 7.49 47 7.9 15.90 11
4. 7.64 45 8. 16.11 10
4.1 7.85 43 8.1 16.33 10
4.2 8.05 41 8.2 16.55 9.7
4.3 8.25 39 8.3 16.77 9.4
4.4 8.45 37 8.4 16.98 9.2
4.5 8.65 35 8.5 17.17 9.0
Flow rate qm [l/s] 4.6 8.85 34 8.6 17.36 8.8
4.7 9.05 32 8.7 17.57 8.6
4.8 9.25 31 8.8 17.78 8.4
4.9 9.47 30 8.9 17.98 8.2
* Avoid presetting < 1, see tolerance curve page 9.
6 2011 Oventrop
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
DN 40
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
* *
Turn
Turn
Turn
Presetting
DN 50
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Presetting *
Turn
Trun
Turn
Pressure loss Δp [mbar]
3. 14.23 62 7. 29.41 15
3.1 14.65 59 7.1 29.75 14
3.2 15.10 55 7.2 30.10 14
3.3 15.50 53 7.3 30.40 14
3.4 15.95 50 7.4 30.75 13
3.5 16.35 47 7.5 31.10 13
3.6 16.80 45 7.6 31.45 13
3.7 17.25 42 7.7 31.80 12
3.8 17.65 40 7.8 32.10 12
3.9 18.10 39 7.9 32.45 12
4. 18.50 37 8. 32.73 12
4.1 19.00 35 8.1 33.15 11
4.2 19.45 33 8.2 33.55 11
4.3 19.85 32 8.3 33.90 11
4.4 20.30 31 8.4 34.30 11
4.5 20.70 29 8.5 34.70 10
4.6 21.15 28 8.6 35.10 10
4.7 21.60 27 8.7 35.50 10
4.8 22.05 26 8.8 35.90 9.8
Flow rate qm [l/s] 4.9 22.50 25 8.9 36.30 9.6
2011 Oventrop 7
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
DN 65
Zeta-value
Zeta-value
Zeta-value
kv-value
kv-value
kv-value
Turn
Turn
Turn
Presetting
Presetting:
1. The value of presetting of the valve is set by turning the hand- Marking
wheel. Sliding
Fine setting scale
a. The display of the basic setting is shown by the longitudinal indicator
(peripheral scale)
scale together with the sliding indicator.
0
1
Handwheel
5
7
gitudinal scale.
b. The display of the fine setting is shown by the peripheral scale
0
Colour ring
1
handwheel.
2. Limitation of the set value of presetting by turning the inner Basic setting
adjustment stem clockwise until it seats. This can be done by scale
using the long end of a 3 mm Allen key. (longitudinal scale)
8 2011 Oventrop
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
H Dimensions:
DN
DN B L L1 H h h1
h1
Dimensions:
DN B L L1 H
H
Tender specification:
Insulation shells made of closed-cell foamed polyethylene with additional solid mesh effect made of polypropylene;
one-piece insulation of symmetric construction with tongue-and-groove fitting.
Only for heating systems.
Operating temperature ts: 100°C
Installation advice:
Oventrop double regulating and commissioning valves serve to forms to the arrow on the valve body. The flow tolerance is 5%.
achieve the hydronic balance between the various circuits of a sy- If installed against the flow, an increase in the flow rate of 1-3%,
stem. It is therefore to be observed that the direction of flow con- related to the chart value, must be considered.
2011 Oventrop 9
Bronze double regulating and commissioning valves PN 16/PN 25
“Hydrocontrol VTR/VPR”
Correction factor f
Correction factor f
1.3
When antifreeze liquids are added to the hea- 1.3
20 °C
ting water, the values given in the chart must 35 °C
be multiplied by the correction factor f.
1.2 1.2
35 °C
50 °C
50 °C
1.1 1.1
65 °C
65 °C
80 °C
1.0 1.0 80 °C
0.9 0.9
0.8 0.8
10 20 30 40 50 10 20 30 40 50
Weight proportion of ethylene glycol [%] Weight proportion of propylene glycol [%]
10 2011 Oventrop
OVENTROP GmbH & Co. KG
Paul-Oventrop-Straße 1
D-59939 Olsberg
Subject to technical modification without notice. Phone +49 (0)29 62 82-0
Product group 3 Fax +49 (0)29 62 82-450
ti 19-1/10/MW E-Mail mail@oventrop.de
Edition 2011 Internet www.oventrop.com
OVENTROP GmbH & Co. KG
Paul-Oventrop-Straße 1
D-59939 Olsberg
Subject to technical modification without notice. Phone +49 (0)29 62 82-0
Product group 3 Fax +49 (0)29 62 82-450
ti 19-1/10/MW E-Mail mail@oventrop.de
Edition 2011 Internet www.oventrop.com
12 2011 Oventrop