STANDARD TYPE
an
ou +
iE 1 if
=a, | “
Dimension 3 be
eae T L
ue af) fo tHt-0 |
UPE 1 | ,
wow et ,
bo
Model SA110 AIBIC SA111 A/B/C SA120 AIBIC
[STANDARD TYPE ] [ STANDARD TYPE ] [ HI-TEMP. TYPE]
pseu -20°C-80°C -20°C~80°C 2ru-200G
Temp.
Probe
Material ‘SUS 304 SUS 304 ‘SUS 304
Insulated
Material UPE UPE PIFE
‘Connection | T'PT screw (SUS) "PT screw (SUS) "PT screw (SUS)
Sensitivity 10pf (sta) opt (si) 410pf (std.)
Range 20pr, 40pf option 20pI, 40pf option 20pf. 40pf option
Weight ‘Approx. 1.99 ‘Approx. 1.9kg Approx. 2.4kg
Housing Aluminum IP6S
‘Spec.
‘Supply
ieee ‘1o/2z0vac = 10% or 2406
Delay
me 0-6 seconds
Power
|Consumption| aw
Contact SA/240VAC or SA/30VDC, SPDT or NPN 100mA.
Rating
if length of sensing probes longer than 3 meters, please chose 20pf or 40pf sensitvily typeADJUSTMENT
ooo
= COARSE CALIBRATION
‘Set the "Sensitive ADJ." to the "H" position. Then:
use a screw driver to adjust the “Coarse” until
indicator is lighted. At last check “Indicator* is light
or nat by adjust the "Sensitivity Ad" knob, if not,
repeat procedure,
= SENSITIVITY ADJUSTMENT
When the material is out of contact with probe will
extinguish the “Indicator’. When the material is in
sontact with probe will illuminated the “Indicat
lamp, at this time please adjust "Sensitivity ADJ”
until lamp is in extinction, And then set "Sensitivity
ADU." in the middle between "H” and extinction
position. e.g. If extinction position is 10p. you
should set "Sensitivity ADJ” in *75" position
Ge a
SA-TYPELEVEL SENSOR
SENSITIVITY. ADL = IES Mo.
Ont TP. Sani. O
re NM
= DELAY FUNCTION CALIBRATION
‘Tho dofauit cotting ic 0 sceond, hore at the
material is in contact with probe will illuminate
“Indicator® lamp and energize relay. When the
user need to use this delay function, please set
timer in clockwise. The relay will energized after
“Indicator” illuminate for several seconds if set
fimer more than 0 second. The delay function is
suitable for variable material level. e.g. liquid tank
equip with agitator.
wa
SR
Uranded shield —
Source
Normal el
To sensor a =
coaxial cable ‘Normal open
OO-120- 155 ‘Common
Remote Probe Type (SA140 A/B/C)
Normal close
Normal open ——— << Power
Commen L_.¢_Soures
‘SA110, 120, 130, 150, 160, 17, 180 A/BICIDINSTALLATION NOTICE
be
g
Np if
LA “eg
L>3tnm gAnO
‘The insensible portion should
be mounted to protrudes 3Gnnu
from the vessel wall. That's to
prevent malfunction trom a fill
‘material or an insufficient clear
ance Detween probe and oon
nection pipe.
if tho probe is mounted on the
top, make sure the length of
probe long enough to touch the
highest level of raw material
SAA50 type musi have at least
BG0nun ham the stectrode
pprobe to the silo vail
SA160 type is usually installed
al the lower of tank side.
SA160 to be mounted property.
the vessel walls slnvuld nol ex
‘ceed 25mm
(
For Non-Slationary o- witeating
environment, a separate control
unit such as the SA140 is sug-
gested.
To prevent (aise readings, users
have to make sine the mater!
flows symmetrically f the inlet is
not located in the cenier partion
of the tank roof, check the flow
patter («angle of your materia!
and ples Une pul in thre pore
priate location.
Itig suggested to install the
probe away from the inlet to 1e-
duce the risk of inflowing mate-
fial damaging the probe. Ifthe
probe is near an inlet, itis rac-
ammender tn place a protectve
cower 200mm above the probe.
The cover should be parallel to
the probe and the same length