Professional Documents
Culture Documents
Hexaflexagon - How To Make An Infinity Loop - Chaotically Yours
Hexaflexagon - How To Make An Infinity Loop - Chaotically Yours
Loop
9 Comments
A hexaflexagon is one of the coolest things my kids have ever learned how
to make!
They’re also a really great STEM activity, helping kids learn about geometry,
engineering, patterns, and art!
Links in this post may be affiliate links, which means I may earn a
commission if you make a purchase from any of them. You can read my full
disclaimer HERE.
We’ve made optical illusions, greeting cards, explosion boxes and even
cartoons with them! The possibilities are endless with these awesome
shapes!
It does takes a little bit of patience to learn when you’re getting started, but
once you master the concept, a hexaflexagon can be made in a matter of a
few minutes.
Subscribe to Chaotically Yours!
Get monthly updates on the latest posts and more from
Chaotically Yours straight to your inbox.
It’s also perfect for almost any age kids, but particularly older elementary
and middle school students since it really emphasizes the use of geometry
and angles.
a ruler
a pencil
scissors
a glue stick (tape or regular glue can be used in a pinch, but we MUCH
prefer using a glue stick)
Once you’ve gathered these items up, it’s very easy to get started!
Hexaflexagon
Hexaflexagons can be made in just about any size, as long as you get your
measurements right.
I’ve found that for a standard size piece of copy paper (8.5 x 11 inches), that
the width of 1.5 inches is the perfect size.
Measuring and Cutting
You’ll want to measure and cut a strip of paper that is 1.5 inches wide and
11 inches long (the length of the longest side of the paper).
I can get five 1.5 x 11 inch strips of paper from one regular size piece of
copy paper, with a small strip left over.
After you have your strip of paper, on the longer side of the paper, you’ll
want to measure 3/4 inch from the top and make a mark. then draw a line
from the opposite corner of the paper to your mark.
Once you’ve marked your strip, you need to cut along the line, trimming
your strip at an angle. See the picture below to get an idea of what I’m
talking about.
If you are using a different size other than a 1.5 x 11 inch strip, you’ll want
to measure half the distance of the shortest side of the paper. For example,
if your strips are 2 inches wide, you should measure down one inch to get
your mark.
Start with the end of the strip that you just cut so that it’s angled.
Fold that side so that the angled side you just cut is even with the straight
side of the strip, forming a triangle. Press down hard on your fold so it is
nice and crisp.
Flip the strip over and do this again, making sure the sides line up as
perfectly as you can get them. Flip the strip over and repeat the fold. The
video below should help you understand what we’re going for here.
Folding a Hexaflexagon
This is very important: Make sure you have a chain of ten complete
triangles and trim off the rest. The video below should make it clear exactly
where you need to cut.
Trimming a Hexaflexagon
Connecting the Loop
You’ve done all the hard work now! We’re almost done. Now you just need
to connect your hexaflexagon to make the infinity loop!
This part can be a little tricky, so take it slow. Once you get the hang of it, it
will all come together naturally!.
Take the end of the strip and leave two triangles open. Let the third and
fourth triangles lay against each other, in the direction you folded them.
Leave the fifth triangle open. Let the sixth and seventh triangles lay against
each other, just like you did with the third and fourth.
Leave the eighth triangle open. The ninth triangle will tuck under the first
triangle, and the tenth triangle will be hanging out of the loop.
Put a little bit of glue on the tenth triangle, and fold it over, connecting it to
you first triangle. Now you’ve made your loop!
To test out if you folded your loop correctly, pinch the loop into three
“wings” where the paper folds back against itself. You should be able to
open the loop from the middle outward.
Once it’s open, you should be able to pinch the wings again and open from
the middle, exactly like the last time you opened it.
I know all of this is confusing, but the video below should clarify it all
somewhat.
Connecting a Hexaflexagon
You can use any type of crayons or marker on them that you like.