Professional Documents
Culture Documents
Group Recrument
To whom it may concern
Please accept this letter and the accompanying resume as an expression of my interest in a position related
with your organization.
As my resume indicates, in Aug 2011, I had graduated to receive a Bachelor of Mechanical Engineering
(Mechanical - Automotive). After that I had been well trained and gain knowledge and skillful with two
company and present for 8 years in mechanical engineering field.
I have a good knowledge in do maintenance and service equipment, provide proper total maintenance plan
and eliminate long delay hours on productivities. I have an ability to grow with a job, handle
responsibility and build positive relationships with work colleagues at all levels. My present employer is
very satisfied with my work rate, and I am confident that I can bring the same level of high performance
to your company.
I am certain I could make significant contributions to your organization, and I would welcome the
opportunity to meet you to discuss how my work experience and abilities might best be employed by your
organization.
Thank you for the time you have taken to consider my application, and I eagerly look forward to hearing
from you.
Sincerely
Encl: Resume
From JobStreet.com
Mohamad Ridzuan Bin Abd Halim
Electrical Maintenance Engineer
at Westports Malaysia Sdn.Bhd
(+60) 013 211 8674 | mridzuan.halim@gmail.com | 870222-02-5203 | 34 years old
Address Unit 712, Apartment Inai Court, Jln Templer, 46000 Petaling Jaya,
Selangor
Education Universiti Teknologi Malaysia, Skudai Johor.
Degree of Mechanical Engineering (Mechanical - Automotive) (2011)
Nationality Malaysia
Job Experience
Mac 2020 - Present Electrical Maintenance Engineer
(11 months) Westports Malaysia Sdn.Bhd
Execution of periodic condition based maintenance for entire electrical facilities in port area such building,
street/bridge light, high mass, warehouse and etc. Ensure port areas are sufficient with lightning to avoid
hazardous incident. Perform a safety relay audit (OC, EF, OCEF, etc.) and ensure that the safety relay is
properly calibrated before the expiration date. Maintain backup generator at every substations; do
with/without load test on generator to ensure efficiency during downtime not affected. Study on monthly
electricity consumption analysis on each area.
Project Experience
Oct 2016 (ongoing) Refurbishment obsolete passenger hoist for Quay Crane
container (CAPEX)
Westports Malaysia Sdn.Bhd
Annually project (improvement project - CAPEX) had approved by community and ongoing project for
approval JKKP to dismantle old passenger hoist and installation complete new brand. Old passenger hoist
were very critical condition, heavy vibration traveling and unsafe as carried passenger. New model have
integrated inverter drive as acting soft start/landed travelling instead of direct online system (old unit).
Jan 2013 350 tone per hour (t/hr) Aggregate & Sand Washing Plant in Qatar
(ASWP)
Ramill Tech W.L.L Doha, Qatar
Aggregate and sand washing plant (ASWP) was built in Mukaynes, Qatar. This plant is design to suit 350
t/hr of production together with water recycle and sludge/clay control system.
May 2012 150 m3/hr Bentonite Treatment and Slurry Separation Plant
(Desander)
Ramill Tech (M) Sdn. Bhd, Malaysia
Desander was design for tunneling purpose. Purpose for solid control equipment with a set of hydro cyclones
that separate sand and silt from the drilling fluids in drilling rigs, it’s also were used for exploration in oil and
gas industries.
From JobStreet.com
Education
2008-2011 Universiti Universiti Teknologi Malaysia, Skudai Johor
Degree of Mechanical Engineering (Mechanical - Automotive)
Major Mechanical - Automotive
CGPA 3.06
Certified
1. Graduate Engineer by BEM (Reg: 87840A)
2. QLASSIC Awareness Course &Assessor Certification Programme
3. FUJI Inverter/ Converter Troubleshooting and PLC Diagnosis
4. OSHA and HIRAC
5. Compress Air System, Operation, Maintenance & Safety
6. Electrical for Non- Electrical Engineer and Troubleshooting
7. 5S Implementation
Site Visit Factory Acceptance Test (FAT) of Industrial Elevator ALIMAK at Sweden
Skills
MS Office & SAP 90%
Cost Management 80%
Team Leadership 90%
AutoCAD 70%
Maintenance & Repair 90%
Commissioning 80%
Eectrical Engineering 60%
Troubleshooting 70%
Languages
From JobStreet.com
Objective
To secure an engineering position with an aggressive international company
To seek for a challenging position which will utilize my knowledge and in the same time
provide rooms for growth and career development
To get acquainted with the organization structure & business operations of a company and to
be able to contribute positively to the future of a company
Strengths
Leadership charisma
Dynamic team player
Sense of responsibility
Highly inquisitive
Creative and resourceful
Excellent skills in communication and collaboration as well as negotiation
References
Reference #1 Ir.Musaddiq Bin Othman, Senior Engineer of Department Maintenance & Repair, Westports Malaysia Sdn Bhd
+60123 731 9658
Reference #2 Norhadi Ishari, Business Development & Project Director, Ramill Tech (M) Sdn Bhd
+6016 210 0468
From JobStreet.com