Professional Documents
Culture Documents
Speaker Amplifire
Speaker Amplifire
Lab project/PBL
Dated: 26-July-2023
1|Page
Table of Contents
Task 1: ..................................................................................................................................................4
Objective: .............................................................................................................................................4
Wien Bridge Oscillator .........................................................................................................................4
Introduction ..........................................................................................................................................4
Mathematical Calculations ...................................................................................................................5
Multisim Implementation .....................................................................................................................7
Output waveform ..................................................................................................................................8
Output Frequency .................................................................................................................................8
Task 2: ..................................................................................................................................................9
Objective: .............................................................................................................................................9
Multivibrator ........................................................................................................................................9
Astable multivibrator..........................................................................................................................10
Monostable Multivibrator: .................................................................................................................10
Bistable multivibrator .........................................................................................................................11
Working ..............................................................................................................................................13
Mathematical Calculations .................................................................................................................13
Multisim Implementation ...................................................................................................................14
Task 3: ................................................................................................................................................15
Function Generator: ............................................................................................................................16
1) Sine-wave generator .......................................................................................................................16
Multisim Implementation: ..................................................................................................................17
Hand Calculations: .............................................................................................................................17
Maximum and Minimum frequency: .................................................................................................18
Simulated Values: ...............................................................................................................................20
2) Square-wave generator...................................................................................................................20
Multisim Implementation: ..................................................................................................................21
Output waveform: ..............................................................................................................................22
3) Triangular-wave generator .............................................................................................................22
Multisim Implementation: ..................................................................................................................24
2|Page
Output waveform: ..............................................................................................................................24
Overall Function Generator Circuit ....................................................................................................25
Multisim Implementation: ..................................................................................................................25
Conclusion ..........................................................................................................................................27
Table of Figures
Figure 1 Wien bridge oscillator ............................................................................................................4
Figure 2 Modified Wein bridge Oscillator ...........................................................................................6
Figure 3 wein bridge oscillator software ..............................................................................................7
Figure 4 Output Wave form of Wein bridge oscillation .......................................................................8
Figure 5 Output Frequency of Wein bridge oscillator ..........................................................................8
Figure 6 op-amp astable multivibrator .................................................................................................9
Figure 7 Multivibrator basic configuration ........................................................................................10
Figure 8 Astable multivibrator circuit ................................................................................................10
Figure 9 Monostable multivibrator circuit .........................................................................................11
Figure 10 Bistable multivibrator circuit .............................................................................................12
Figure 11 Op-Amp Astable and Monostable Multivibrator ...............................................................12
Figure 12 Multisim Implementation of Multivibrator Circuit ...........................................................14
Figure 13 Output Waveform ...............................................................................................................15
Figure 14 Output Frequency ..............................................................................................................15
Figure 15 Working of Function Generator .........................................................................................16
Figure 16 sine wave generator software ............................................................................................17
Figure 17 Output of sine-wave generator with max frequency ..........................................................19
Figure 18 Output of sine-wave generator with min frequency .........................................................19
Figure 19 Operation of Bounded Comparator ....................................................................................21
Figure 20 Square wave generator softwar ..........................................................................................21
Figure 21 Output Waveform of Square Wave Generator ...................................................................22
Figure 22 Voltage in an integrator ......................................................................................................23
Figure 23 An op-amp integrator .........................................................................................................23
Figure 24 Triangular wave Generator software ..................................................................................24
Figure 25 Output waveform of square wave generator ......................................................................24
Figure 26 Function generator steps ....................................................................................................25
Figure 27 Function Generator Software .............................................................................................25
Figure 28 Output wave form ..............................................................................................................26
Figure 29 Output Waveform at 15kHz ...............................................................................................26
Figure 30 Output Waveform at 15Hz .................................................................................................27
3|Page
Task 1:
Objective:
Modified a Wien-bridge circuit to oscillate at a specified frequency.
Specifications:
Design the Wien-bridge oscillator shown in Figure 1 to oscillate at fr = 20 kHz.
Choices:
An ideal op-amp is available and standard-valued resistors and capacitors are to be
used.
Introduction
Oscillators are circuits that generate periodic waveforms without requiring an input
signal. They typically utilize active devices like transistors or operational amplifiers
(OPAMPs) as amplifiers, along with passive components such as resistors,
capacitors, or inductors in a feedback network. One commonly used oscillator is the
Wien bridge oscillator, which is known for its simplicity. In this configuration an
OPAMP is employed as the amplifying device, and the Wien bridge acts as the
feedback element.
4|Page
To achieve oscillations, the OPAMP is used in the noninverting mode, which
introduces a phase shift of 0 degrees. It is expected that the feedback network also
introduces a phase shift of 0 degrees at the oscillation frequency.
The feedback network provides a gain of 1/3. Consequently, the amplifier gain in the
inverting mode should be slightly higher than 3.
Mathematical Calculations
Given Frequency
fr=20KHz
We know that
5|Page
Solving for R.
Let us
assume
6|Page
Multisim Implementation
Multisim Implementation
7|Page
Output waveform
Output Frequency
8|Page
Task 2:
Objective:
Design and Build a Simple Monostable Multivibrator Circuit
Specifications:
Modify the given A-stable multivibrator to behave as a Monostable Multivibrator
Choices:
An ideal op-amp and diode are available and standard-valued resistors and
capacitors are to be used.
Multivibrator
Multivibrators are a group of regenerative circuits commonly used in timing
applications. They function as wave-shaping circuits, producing symmetric or
asymmetric square wave outputs. These circuits have two distinct states: stable and
quasi-stable, which depend on the specific type of multivibrator being used.
Astable multivibrator
An astable multivibrator is a free-running oscillator that exhibits two quasi-stable
states. As a result, it oscillates between these states without requiring any external
signals to initiate the state change. In this configuration, the two states are only stable
for a limited time, and the circuit alternates between them, producing output
waveforms with positive and negative saturation values.
Monostable Multivibrator:
A monostable multivibrator has one stable state and one quasi-stable state. The
circuit remains in its stable state until an external triggering pulse causes a transition
to the quasi-stable state. After a period of time (T), the circuit returns to its stable
state. Hence, it generates a single output pulse in response to an input pulse and is
10 | P a g e
commonly referred to as a "one-shot" or "single shot" multivibrator. The transition
back to the stable state is triggered by an external signal, which is typically generated
through the charging and discharging of a capacitor.
A monostable multivibrator generates a single pulse of specified duration in response
to each external trigger signal. Initially, the circuit is in the stable state. When a
specific "event" occurs, it enters the transient state, remains in that state for a time
interval (T), and then returns to its stable state.
Bistable multivibrator
A bistable multivibrator, also known as a flip-flop, is a type of multivibrator that has
two stable states. Unlike astable and monostable multivibrators, a bistable
multivibrator remains in its current state until it is triggered to switch to the other
state.
The bistable multivibrator circuit typically consists of two cross-coupled NAND or
NOR gates, forming a positive feedback loop. Each gate's output is connected to the
input of the other gate, creating a mutually reinforcing loop. The two stable states of
the bistable multivibrator are usually referred to as "SET" and "RESET" states.
When a triggering signal is applied to the circuit, it causes the bistable multivibrator
to switch from one stable state to the other. For example, if the circuit is in the SET
state, a trigger signal will cause it to transition to the RESET state. Once in the new
state, the bistable multivibrator remains in that state until it receives another
triggering signal to switch back.
11 | P a g e
The bistable multivibrator is commonly used in digital circuits and memory
elements. It can store a bit of information, representing a logical "1" or "0,"
depending on its current stable state. The state of the bistable multivibrator can be
changed and read by applying appropriate triggering signals.
Overall, the bistable multivibrator provides a means of storing and retaining binary
information, making it a fundamental building block in digital electronics and
sequential logic circuits.
12 | P a g e
Working
By introducing a diode in parallel with the capacitor in the astable multivibrator
circuit, we can convert it into a monostable circuit. In the modified circuit, the
triggering signal is applied at the node where resistors R1 and R2 are connected.
Let's assume that the output of the circuit is at positive saturation voltage, or the
output of the op-amp is positive. In this case, the voltage at node A can be calculated
as (R2/(R1+R2)) * Vsat. When the output voltage is at positive saturation, diode D1
becomes forward biased, and the voltage across capacitor C1 becomes the forward
voltage drop across the diode. Since the output voltage is higher than the voltage at
the inverting node, the output of the op-amp remains at positive saturation voltage.
Next, we apply a negative trigger pulse at node A. When this trigger signal is applied,
the voltage at the non-inverting node becomes lower than the voltage at the inverting
node. As a result, the output of the op-amp switches from positive saturation voltage
to negative saturation voltage, and the circuit enters the quasi-stable state. Since the
output voltage is at the negative saturation voltage, the diode becomes reverse biased,
and the capacitor begins to charge towards the negative saturation voltage.
By adding a diode to the astable multivibrator circuit and applying a trigger pulse at
the appropriate node, we can create a monostable circuit that generates a single
output pulse in response to each trigger signal.
Mathematical Calculations
The period ‘T’ is determined by the values of the resistor R3, the capacitor C1, and
the values of the Feedback resistors, and for the given circuit, the time-period can be
calculated by
With the formula sorted outlets design a monostable multivibrator that has a time
period of 100ms. For simplicity, we are going to be using two 10K resistors for 𝑅1
𝑎𝑛𝑑 𝑅2 . By doing so, the expression becomes,
13 | P a g e
Let us assume capacitor value of 10uF So
T=100ms
C=10uF
100ms=0.693*R*10uF
R=15K
Multisim Implementation
14 | P a g e
Figure 13 Output Waveform
Task 3:
Objective:
Design a simple function generator
Specifications:
it should be capable of generating square, Triangular and sinusoidal waves.
Choices:An ideal op-amp is available and standard-valued resistors and capacitors
are to be used. Use +/- 9V dual supply for powering the circuit.
15 | P a g e
Function Generator:
In the field of modern electronic systems, wave generators serve as versatile tools
for generating electrical waveforms. They can be used as standalone signal sources
or as integrated components within sensing systems to provide excitation and
control signals. The ability to tune the amplitude and frequency independently adds
flexibility to the system, making them essential in various applications such as
micromachined resistive and capacitive sensors. A function generator is a common
piece of electronic test equipment or software used to generate different types of
electrical waveforms across a wide range of frequencies. The function generator can
produce waveforms such as sine waves, square waves, triangular waves, and more.
1) Sine-wave generator
One example of a wave generator is the sinusoidal-wave generator, which utilizes
op-amp based active circuits. The canonic sinusoidal oscillator, known as the Wien-
Bridge Oscillator, is a classic application of this approach. It typically consists of
one op-amp, four resistors, and two capacitors. The Wien-Bridge Oscillator
generates an oscillatory output signal without requiring an external input source. It
is commonly used in low-frequency oscillating circuits. The basic configuration of a
Wien-Bridge Oscillator is shown in Figure 1. It employs two RC networks
connected to the positive terminal to form a frequency-selective feedback network,
which facilitates the occurrence of oscillations. The signal is amplified through the
16 | P a g e
use of negative feedback resistors. This oscillator design has found wide application
due to its simplicity and effectiveness in generating sinusoidal waveforms at low
frequencies.
Multisim Implementation:
Hand Calculations:
For frequency:
Let us assume capacitance value is 1000nF, and take resistor 10K then,
The frequency of oscillations for a Wien Bridge Oscillator is given as:
Where:
fr is the Resonant Frequency in Hertz
R is the Resistance in Ohms
C is the Capacitance in Farads
Finding Value of resistor and capacitor:
17 | P a g e
To find the value of R & C, fixed one circuit element and find
f=15KHz
𝑹 = 𝟏𝟎𝑲Ohm
To achieve desirable frequency, vary RC values to get different range of frequencies.
At C=1nF
18 | P a g e
Figure 17 Output of sine-wave generator with max frequency
19 | P a g e
Simulated Values:
𝒇𝒎𝒂𝒙 = 𝟏𝟓𝟎𝟖𝟓𝑯𝒛
2) Square-wave generator
When the anode of a zener diode is connected to the inverting (-) input of an
amplifier, it creates a virtual ground that is approximately at 0V. As a result, when
the output voltage reaches a positive value equal to the zener voltage, the zener diode
starts to limit the voltage at that value. This means that the output voltage cannot
exceed the zener voltage in the positive direction. On the other hand, when the output
voltage switches to a negative value, the zener diode behaves like a regular diode
and becomes forward-biased at around 0.7V. This forward-biased condition limits
the negative output voltage to approximately 0.7V. In this way, the zener diode
prevents the output voltage from dropping below this value. By reversing the
orientation of the zener diode, the voltage limiting effect can be achieved in the
opposite direction. The zener diode will limit the output voltage in the same manner,
but now in the opposite polarity.
Overall, by utilizing the zener diode in this configuration, the output voltage of the
amplifier is restricted and clamped within specific voltage limits, depending on the
zener diode's characteristics and orientation.
20 | P a g e
Figure 19 Operation of Bounded Comparator
Two zener diodes arranged as in Figure 5 limits the output voltage to the zener
voltage plus the forward voltage drop (0.7V) of the forward-biased zener, both
positively and negatively, as shown.
Multisim Implementation:
21 | P a g e
Output waveform:
3) Triangular-wave generator
22 | P a g e
Figure 22 Voltage in an integrator
23 | P a g e
Multisim Implementation:
Output waveform:
24 | P a g e
Overall Function Generator Circuit
To sum up, use a RC Wien Bridge to generate sinusoidal-wave, use a comparator to
achieve square wave, and use an integrating circuit to obtain triangular-wave.
Multisim Implementation:
25 | P a g e
Figure 28 Output wave form
At 15KHz :
26 | P a g e
At 15Hz
Conclusion
In conclusion, this lab report explored the construction and analysis of three different
electronic circuits: a Wien bridge oscillator, a monostable multivibrator, and a
function generator.The Wien bridge oscillator was designed to generate a sinusoidal
waveform at a specific frequency determined by the values of its resistors and
capacitors.
The monostable multivibrator, was utilized to produce a single pulse of a
predetermined width in response to a triggering input. The monostable multivibrator
proved to be a versatile circuit for generating precise and controlled pulses. The
function generator allowed us to generate a wide range of periodic waveforms with
adjustable frequency, amplitude, and waveform shape. By utilizing a combination of
op-amps, resistors, capacitors, and potentiometers, we were able to create sine,
square, and triangular waveforms. This versatile circuit provided us with a valuable
tool for signal generation in various applications.
27 | P a g e