Professional Documents
Culture Documents
4. Install LMT by Double Click file WinPcap_4_1_3.exe , follow the step, next, next….until finish.
5. Open folder C:\Software\LMT Software\LMT_EN\Program Files and find file LMT.exe (red
circle)
Password:111111
7. Create a BTS node, click “+” add station :IP address is 172.27.245.92 ,BS type is 4G.as below
picture:
Notice:
During the BTS version upgrade process, the BTS cannot be powered off, otherwise the BTS will
malfunction and need to be repaired.
Choose the storage path of cfgdata、BBU software、RRU software, and click “Start”; the activation time
lasts about 25-30minutes, the BTS will reboot two times, and the LMT link will be disconnected and
self-connected.
Notice:
1) If step One - step Three produce a failed step, click ‘×’ close the interface ;please check the file
selection and try again; if it fails again, Please use the second method to upgrade.
2) If step One - step Three success ,step Four failed means cfgdate and software upgrade
successful , should check the transmission and core network whether configuration completed
and check the BBU status as chapter 4.
3) Before the end of the one-click on station, a window will pop up, prompting the successful or
failure of the site on-air, and save the self-test result.
Upgrade step by step, new site upgrade sequence is cfgdata->BBU SW->RRU SW;
1. Check and set the BTS self-startup model is ‘off’ first.
After download cfgdata successful,please reboot the BTS. Then waiting for LMT re-connect.
4. Select the folder where the " EBB5326_V7.00.16*.dtz " file is stored -> select the "
EBB5326_V7.00.16*.dtz " file, and then right-click to select “Download”.
After the BBU software is successfully upgraded, it will automatically reboot. It may cost a long time.
After rebooting successfully, Please check that the board status is “ terminating” as below picture,
bpoi need about 6-10 minutes change to “terminating” status.
According to default setting in this window, select the “Active Flag” to “instantActivate”, and click
“OK”. Wait until all parts of RRU software package download successfully. After the RRU software
is successfully upgraded, RRU will automatically reboot. It may cost a few minutes.
2. Check and Modify OMLink, Select “TLSNB”->”Office”-> “OMLink” on the left side . Then ‘Entry
of OM Link’ . Right click blank-> select “Modify Entry of OMLink” -> “SetOmlinkPare”, as shown
in below picture.
3. Check and Modify BTS IP Configuration: Select “TLSNB”->”transport”-> “ipAddr” on the left side.
Then ‘Entry of IP Address’ interface displays. One way is Double-click to modify the “Local IP
Address” of the plan.Another way Right click blank-> select “Add Command” -> “AddAddrInfo”, as
shown in below picture.
4. Check and Modify SCTP Configuration of the S1 Port: Select “TLSNB”->”transport”-> “SCTP” on
the left side. Then Double-click to modify the “SCTP parameter” of the plan.
Make sure “Index of SCTP Association” is not repetitive with others. Please make “Index of IP
Address 1” same with “Index of IP address”
“Work Mode”select “client”.
“Peer IP Address Type” select “ipv4”.
Enter mme IP in “Peer IP Address 1”.
“Sctp Link AP Type” selects “mme”.
FiberHome Telkominfra MTD
th
Address: 30 floor, Suite 7, APL Tower. Jl. LetJend. S.Parman, Kav. 28. West Jakarta 11470 - 16 -
“SCTP Link Peer Port Number” selects “0”.
“Peer NE Type” selects “ltemme”.
5. Check and Modify SCTP Stream
8. TdlteCell Configuration
Enter into the interface ‘Entry of Cell network parameters’. Select LTE service → TdLteCell check
and modify according to parameter planning.
No Transceiver Transmit Rate Ofp port status Ofp Bit Error Rate
If Transceiver Transmit Rate is not this value means the SFP is incorrectly plugged in ;
Ofp port normally status is UP state;
Ofp Bit Error Rate value less then 100 and refresh will not increase is normal status.