Professional Documents
Culture Documents
gehealthcare.com
Technical
Publication
5116376
Revision 20
Operating Documentation
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
警告 • 本维修手册仅提供英文版本。
(ZH-CN) • 如果维修服务提供商需要非英文版本,客户需自行提供翻译服务。
• 未详细阅读和完全理解本维修手册之前,不得进行维修。
• 忽略本警告可能对维修人员,操作员或患者造成触电、机械伤害或其他形式的
伤害。
a
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
b
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
警告 • このサービスマニュアルには英語版しかありません。
(JA) • サービスを担当される業者が英語以外の言語を要求される場合、翻訳作業は
その業者の責任で行うものとさせていただきます。
• このサービスマニュアルを熟読し理解せずに、装置のサービスを行わないで
ください。
• この警告に従わない場合、サービスを担当される方、操作員あるいは患者さ
んが、感電や機械的又はその他の危険により負傷する可能性があります。
c
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
d
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
e
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
警告 • 本服務手冊僅提供英文版本。
(ZH-HK) • 倘若客戶的服務供應商需要英文以外之服務手冊,客戶有責任提供翻譯服務。
• 除非已參閱本服務手冊及明白其內容,否則切勿嘗試維修設備。
• 不遵從本警告或會令服務供應商、網絡供應商或病人受到觸電、機械性或其他
的危險。
f
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
警告 • 本維修手冊僅有英文版。
(ZH-TW) • 若客戶的維修廠商需要英文版以外的語言,應由客戶自行提供翻譯服務。
• 請勿試圖維修本設備,除非 您已查閱並瞭解本維修手冊。
• 若未留意本警告,可能導致維修廠商、操作員或病患因觸電、機械或其他危險
而受傷。
DAMAGE IN TRANSPORTATION
All packages should be closely examined at time of delivery. If damage is apparent write “Damage In Shipment” on ALL
copies of the freight or express bill BEFORE delivery is accepted or “signed for” by a GE representative or hospital receiving
agent. Whether noted or concealed, damage MUST be reported to the carrier immediately upon discovery, or in any event,
within 14 days after receipt, and the contents and containers held for inspection by the carrier. A transportation company
will not pay a claim for damage if an inspection is not requested within this 14 day period.
To file a report:
Fill out a report on http://egems.med.ge.com/edq/home.jsp
Contact the local service coordinator.
g
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Discard used batteries according to the manufacturer’s
instructions.
h
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 20 5116376
A
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 20 5116376
REVISION HISTORY
REV Date Primary Reason for Change
20 06/12/12 Switch/Jumper Update the SCSI to IDE Adapter Jumper JP1 Setting in SCSI Tower. (Sec. 1)
19 08/17/11 Introduction -
System Added software installation procedure for PMT-10 tower phase in.
OC -
Gantry -
Table -
DAS/Detector -
X-ray Generator -
Switch/Jumper Added Advantech PC mainboard jumper setting. (Sec. 1)
18 06/20/11 System Added ADD/SUB function for Advantech PC patch software V/R5.00 LFC procedure. (Sec. 2)
Updated InSite information for adding CTT6.3.11. (Sec. 2)
Table Updated cradle absolute position adjustment (003 & 004) according to TGP Firmware update.
(Sec. 2)
Switch/Jumper Updated TGP illustration. (Sec. 2)
17 11/08/10 System Updated software loading procedure for Advantech PC. (Sec. 2)
B
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 20 5116376
REVISION HISTORY
REV Date Primary Reason for Change
16 06/17/10 Warning Added Languagewarning for Slovenian.
Gantry Updated figure for power supply voltage adjustment (5136907), added OGP DC Output Connector.
(Sec. 1)
Updated Gantry Tilt Angle Adjustment. (Sec. 5)
DAS/Detector Updated figure for power supply voltage adjustment (5136907), added OGP DC Output Connector.
(Sec. 3)
15 12/09/09 Warning Added three Languagewarnings for HongKong, Taiwan and Croatian.
C
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 20 5116376
REVISION HISTORY
REV Date Primary Reason for Change
11 11/06/07 System Updated software loading for LFC/LFW and patch installation. (Sec. 2)
Added notice for how to get license or password before Alignment and Calibration. (Sec. 3, Sec. 4)
System Deleted 4-17 SETUP PAPER BASED NETWORK COLOR PRINTER. (Sec. 2)
4 08/16/05 System Updated software installation procedures for HP8200 phase-in and OS CTT 4.5.1, Application V/R
2.18 release (Sec. 3)
3 06/24/05 Introduction Updated Raw Data 1000 Option to Raw Data 5000 Option (Sec. 3)
System Updated Illustration 1-5 Voltage Selection (for 200V system) (Sec. 1)
Updated Ejecting DVD-ROM and Insite Installation (Sec. 2)
D
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 5 5116376
INTRODUCTION
TABLE OF CONTENTS
SECTION PAGE
i INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
ii INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
SECTION 1 - GENERAL
WARNING
DEATH OR SERIOUS INJURY!!
READ AND THOROUGHLY UNDERSTAND THE ‘PROSPEED SERIES SAFETY GUIDELINES/
EMC’ MANUAL (5116382) BEFORE PERFORMING ANY PROCEDURE IN THIS ‘FUNCTIONAL
CHECK/ADJUSTMENT.’
1-1 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
1-1-1 Gantry
WARNING
ROTATION AND ELECTROCUTION HAZARDS!
SWITCH OFF THE ‘ROTATE’ AND ‘XG POWER (SAFETY LOOP)’ SWITCHES LOCATED AT
THE REAR OF THE GANTRY BASE BEFORE INSERTING ANY OBJECT INTO OR WORKING
ON THE GANTRY.
WARNING
ROTATION HAZARD!
ALWAYS INSERT THE GANTRY AZIMUTH LOCK PIN BEFORE REPLACING THE TUBE, DAS,
DETECTOR, HV TANK, OR OTHER WEIGHTY COMPONENTS.
WARNING
ELECTROCUTION!
DANGEROUS VOLTAGES ARE PRESENT ON UNSHIELDED TERMINALS. USE EXTREME
CAUTION WHEN WORKING ON LIVE EQUIPMENT.
WARNING
ROTATION HAZARD!
ANY OF THE FOLLOWINGS WILL INITIATE THE GANTRY ROTATION:
1. POWERING ON THE SYSTEM OR GANTRY.
2. SWITCHING ON THE ‘TABLE/TILT’ SWITCH.
3. PUSHING THE RESET SWITCH ON THE TGP BOARD.
4. PUSHING THE POSITIONING LIGHT BUTTON.
5. RESETTING OR POWERING OFF THE HOST COMPUTER.
6. PUSHING THE RESET SWITCH ON THE DBPCI BOARD.
STAND CLEAR OF THE ROTATING GANTRY.
1-2 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
WARNING
ELECTRICAL SHOCK HAZARD !
IF THE SYSTEM HAS UPS ASSY, MAKE SURE YOU TURN OFF THE UPS POWER BEFORE
YOU ACCESS THE OPERATOR CONSOLE.
WARNING
ELECTRICAL SHOCK HAZARD!
DANGEROUS VOLTAGES EXIST ON EXPOSED SURFACES. USE EXTREME CAUTION
WHEN WORKING ON LIVE EQUIPMENT.
CAUTION
Rotating fan assemblies!
Do not place any item into rotating blades. Use extra care when working near fan
assemblies.
NOTICE
Turn OFF power before removing or inserting any board or plug.
1-3 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
kgf•cm 0 1 2 3 4 5 6 7 8 9
N•m
10 0.9807 1.0787 1.1768 1.2748 1.3729 1.4710 1.5690 1.6671 1.7652 1.8632
20 1.9613 2.0594 2.1574 2.2555 2.3536 2.4516 2.5497 2.6478 2.7458 2.8439
30 2.9420 3.0400 3.1381 3.2361 3.3342 3.4323 3.5303 3.6284 3.7265 3.8245
40 3.9226 4.0207 4.1187 4.2168 4.3149 4.4129 4.5110 4.6091 4.7071 4.8052
50 4.9033 5.0013 5.0994 5.1974 5.2955 5.3936 5.4916 5.5897 5.6878 5.7858
60 5.8840 5.9820 6.0800 6.1781 6.2762 6.3742 6.4723 6.5704 6.6684 6.7665
70 6.8646 6.9626 7.0607 7.1587 7.2568 7.3549 7.4529 7.5510 7.6491 7.7474
80 7.8452 7.9433 8.0413 8.1394 8.2375 8.3355 8.4336 8.5317 8.6297 8.7278
90 8.8260 8.9239 9.0220 9.1200 9.2181 9.3162 9.4142 9.5123 9.6104 9.7084
100 9.8065
1-4 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
N•m 0 1 2 3 4 5 6 7 8 9
kgf•cm
0 0 10 20 31 41 51 61 71 82 92
10 102 112 122 133 143 153 163 173 184 194
20 204 214 224 235 245 255 265 275 286 296
30 306 316 326 337 347 357 367 377 388 398
40 408 418 428 439 449 459 469 479 490 500
50 510 520 530 541 551 561 571 581 592 602
60 612 622 632 643 653 663 673 683 694 704
70 714 724 734 745 755 765 775 785 796 806
80 816 826 836 847 857 867 877 887 898 908
90 918 928 938 949 959 969 979 989 1000 1010
100 1020
1-5 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
1 N•m=0.737 lbf•ft
N•m 0 1 2 3 4 5 6 7 8 9
lbf•ft
10 7.370 8.107 8.844 9.581 10.318 11.055 11.792 12.529 13.266 14.003
20 14.740 15.477 16.214 16.951 17.688 18.425 19.162 19.899 20.636 21.373
30 22.110 22.847 23.584 24.321 25.058 25.795 26.532 27.269 28.006 28.743
40 29.480 30.217 30.954 31.691 32.428 33.165 33.902 34.639 35.376 36.113
50 36.850 37.587 38.324 39.061 39.798 40.535 41.272 42.009 42.746 43.483
60 44.220 44.957 45.694 46.431 47.168 47.905 48.642 49.379 50.116 50.853
70 51.590 52.327 53.064 53.801 54.538 55.275 56.012 56.749 57.486 58.223
80 58.960 59.697 60.434 61.171 61.908 62.645 63.382 64.119 64.856 65.593
90 66.330 67.067 67.804 68.541 69.278 70.015 70.752 71.489 72.226 72.963
100 73.700
1-6 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
CAUTION
Use locktite for screws which are installed to the Gantry rotation block. Use stud bolt with
locktite or nylon nut to prevent loosening if a screw is removed in service maintenance.
CAUTION
When you secure stud bolts with locktite, you must keep the screw torque shown in Table
‘Stud Bolt (Steel) with Locktite.’
Do not rotate the Gantry until the locktite hardens. (75 % of maximum strength after 2 hours;
100 % after 16 hours.)
If it is not possible to wait for the time period mentioned above, use nylon nuts.
M4 10
M5 15
M6 35
M8 70
2-1 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
M4 12 13 16
M5 24.5 26.5 33
M6 41.5 44 55
2-2 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
1. Set the Gantry to the 0° position and lower the table to the lowest positon.
2. Switch OFF the OC power and the “Rotate”, “XG Power”, “Safety Loop” and “Table/Tilt” switches at the Gantry
rear base.
3. Remove the two screw caps and mounting bolts, then move the cover forward or rearward to remove the cover.
3-1 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
STUDS
SERVICE
ANGLE
3-2 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
10. Support the Front Cover, lift, and move it toward vertical position as shown in Illustration 3-4.
11. END.
3 Vertical
2 Horizontal
3-3 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376Gantry Cover Remova
Gantry Front Cover Removal for a Small Room (with Short-Foot-Print Mode)
Note
Use this method when table height will be set to 500 ~ 800 mm.
1. Set the Gantry to the 0 degree tilt position.
2. Switch OFF the OC power and the “Rotate”, “XG Power”, “Safety Loop” and “Table/Tilt” switches at the Gantry
rear base.
3. Move the cradle to the OUT limit position.
4. Move the table to the DOWN limit position.
5. Cover the cradle with a cloth (or cover protector: 2225358) on the to prevent the front cover from scratches or
damage.
Cloth
3-4 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
NOTICE
Take care not to damage any Gantry Parts (especially the positioning light) when rotating
the front cover toward the cradle.
3-5 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-6 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Front Rear
Screws Bracket
3-7 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
NOTICE
When installing the Gantry front cover, first cover the front edge of the cradle with a cloth to
prevent the front cover from scratches or damage.
Cloth
CAUTION
If the service angles (cover stand) fall over, they can injure persons. Therefore, after using
the service angles, keep them in a safe place and/or secure them from falling over even when
the customer or other persons accidentally hit the service angles.
3-8 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Illustration 3-7 Measure the distance between the aperture and the support
Tube
Aperture
Support
the Gantry
Rear Cover
3-9 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
• Repeat above steps to assure that the distances difference is within 5mm.
3-10 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Rear
Front
0RXQWLQJ
%ROW [
3-11 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
1
3
independent
2 1
front cover
Screws
Screws
3-12 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Preparation
• One DVD-RAM
Procedures (Method I)
1. Verify that the system is powered ON. If it is not, switch ON the main switch of the OC. The system is started
up, then the main screen appears.
2. Insert the DVD-RAM into the DVD-RAM drive of the SCSI Tower.
3. Click on Service menu icon.
4. Select Save System State.
5. Click on Continue several times according to the messages to be displayed.
The DVD auto-format phase will be started, then the system state data are saved on the DVD-RAM.
6. “System State Saved Successfully” appears. Click on Continue.
3-13 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Procedures
1. Click on Service icon to display the Service Menu desktop, then select Utilities -> Shutdown -> Application
Shutdown.
2. Click on Restorestate.
3. ‘Insert DVD and press confirm.‘ appears. Click on Continue.
4. Insert the DVD-RAM, including the system state data saved in section 3-4-1, into the DVD-RAM drive.
5. ‘This is an Optical Disk containing a file system.‘ appears. Click on Continue.
Note
At this time, you can cancel system-state-data reloading procedure. If ‘Continue‘ is selected, this
procedure can NOT be canceled.
6. ‘Warning: Restoring will erase the previous contents on disk.‘ appears. Click on Continue.
7. ‘System state restored successfully‘ appears. Click on Continue.
8. To remove the DVD-RAM from the DVD-RAM drive, press the Eject button on the DVD-RAM drive.
9. Select Startup to return to the scan panel screen.
3-14 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-15 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
NOTICE
The characters of alphanumerics, underscore, and period ONLY can be used. Other
characters are rejected to input even if they are input.
3-16 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Buttons to be selected
Service Menu Option Installation Main Window Selection Window I Selection Window II
Install Options Install Permanent DVD
Manual
Quit
Flex Trial
Quit
Remove
Quit
1. Click on Service icon to display the Service desktop Menu , then select Utilities -> Shutdown -> Application
Shutdown.
2. On the desktop menu, click on Install Options button located on the upper right of the screen.
3-17 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3. Click on Install.
Note
If you click on an option in the list, the option is highlighted and “Install“ button is disabled. In this
case, enter the cursor in the option screen, then click on the right button of the mouse to enable the
“Install“ button.
3-18 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-19 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
The following screen apears. Insert the option key DVD into the DVD drive, then click on OK.
3-20 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
You can select several options from the list, while pressing the shift key.
b. Click on Install.
The option loading is started, then the message window appears after completion. The option(s) is dis-
played in the “Installed Options” table.
Note
Just after clicking on Install, the setup window might be displayed, depending on the option to be
installed. In this case, a proper entry/selection must be performed. Refer to Option setup window
described in this section.
c. Click on OK.
d. Click on Quit.
e. Eject the option DVD from the DVD drive.
f. When other option(s) is installed, repeat all steps above.
3. When Manual is selected:
Note
Just after clicking on Accept, the setup window might be displayed, depending on the option to be
installed. In this case, a proper entry/selection must be performed. Refer to Option setup window
described in this section.
3-21 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-22 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Note
Just after clicking on Accept, the setup window might be displayed, depending on the option to be
installed. In this case, a proper entry/selection must be performed. Refer to Option setup window
described in this section.
3. The option loading is started, then the following window appears.
Click on OK.
3-23 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Note
‘Days left’ means the remaining days when a customer can use the option as a trial. This number
counts down day by day, then the option will disappear from the option list when ‘Days left’ becomes
0.
When the flex–trial option has expired and the [New Patient] button is clicked, the Option Status Log
window appears so that a customer can know the expired flex–trial option.
5. When other option(s) is installed, repeat all steps above.
6. Click on Quit.
7. Click on shutdown icon in desktop menu. The system is rebooted.
8. Select Startup to return to the scan panel screen.
9. Perform Section 3-4-1, Saving System State Data for backup.
3-24 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
Then after setting the Asymmetric mode, perform the following in this order.
IMPORTANT NOTE: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
The following BOW is performed only to warm up the X-ray tube. So, do NOT adjust the De-
tector position even if the results go out of tolerance.
----------------------------------------------------------------------
• BOW
Perform Service –> Calibration –> Automated Alignment –> BOW –> OK –> Confirm.
• Q–cal Channel Ratio:
Perform Service –> Calibration –> Automated Alignment –> Qcal Channel Ratio –>OK –> Confirm.
• Calibration:
Perform Service –> Calibration –> Service Calibration –> Asymmetric Seq.
• CT # Adjustment:
Perform Service –> Calibration –> CT # Adjustment.
3-25 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-26 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-27 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-28 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 5 5116376
3-29 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
3-30 INTRODUCTION
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
SYSTEM
TABLE OF CONTENTS
SECTION PAGE
i SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
TABLE OF CONTENTS
SECTION PAGE
2-14 OPTION CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
2-15 STARTING UP THE SYSTEM NOW! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
2-16 COMPLETING THE LFC / LFW PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
2-16-1 Restoring Patient Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
2-16-2 Setting Gamma Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
2-16-3 Test Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
2-17 INSITE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
2-17-1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
2-17-2 Installing InSite Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
2-17-3 Setting up InSite Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
2-17-4 Completing the insite installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54
2-17-5 Saving InSite Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55
2-18 DICOM PRINT TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
2-19 APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
2-19-1 Entering the Machine Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
2-19-2 AutoFilm Setting Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60
ii SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
TABLE OF CONTENTS
SECTION PAGE
iii SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
iv SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-1 GENERAL
WARNING
ELECTRICAL SHOCK HAZARD !
IF THE SYSTEM HAS UPS ASSY, MAKE SURE YOU TURN OFF THE UPS POWER BEFORE
YOU ACCESS THE OPERATOR CONSOLE.
This ‘Checks during System Installation’ is performed during the following:
System Installation
Periodic Maintenance.
For System Installation, it is required that all wiring and cabling are complete and equipment is installed.
Proceed to Section 1-2 ‘Checks prior to Applying Power’, and then to Section 1-2 ‘Ground Continuity’, Section 1-3
‘Temperature,’ ... , in the section order.
1-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
CAUTION
Leave all power to the system OFF and tagged until power is called for in specific steps.
OFF
CB1 CB2
1-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
SERVICE
ON
HOME
SPD1
OFF
MID
SVE
OFF
SUB BOARD
MNL FIX SPD0 MID 90DEG
TGP BOARD
CB1
1-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-3 TEMPERATURE
During the installation and start-up of the system you must take continuous temperature checks to make sure the
environment meets specifications listed in Section 3 of the Preinstallation manual. Excessive temperature, coupled
with reduced air flow from clogged filters, may overstress components and cause failures.
Filters
Check and clean all electronic equipment dust filters. GE recommends initially doing this on a weekly basis,
because new installations always have dust and dirt present at this stage. Over a period of time, you may increase
the maintenance interval as site environment improves.
Specifications
During installation, use the temperature/humidity recorder and a thermometer to record the temperature and relative
humidity in the scan room. Make sure the data you collect meets the following temperature and humidity
specifications.
• Scan Room
- -Temperature: 20 C 28 C (at least 5 C/hr gradient)
- -Relative Humidity: 30 70 % RH (Non Condensing)
• Operator’s Room and/or Equipment Room
- -Temperature: 15 C 30 C (at least 5 C/hr gradient)
- -Relative Humidity: 20 80 % RH (Non Condensing)
Action
Contact the air conditioning supplier or your local GE service department when your data fails to meet any
specifications.
1-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
Input Selection
Verify that an input selection on the Power Distribution Unit (See Illustrations 1-4 or 1-5) meets the input power
voltage. If not, correct them.
The ‘input power voltage’ here means the rating voltage specified on the power distribution box (hospital supply),
not the measured voltage on the power distribution box.
PROTECTION COVER
TRANSFORMER
1-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
120V 200V
TRANSFORMER
PROTECTION COVER
1-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
Action
Investigate any condition that falls out of spec. Identify the problem source(s) and resolve the problem.
1-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
WARNING
DANGEROUS VOLTAGES EXIST WITHIN THE UNIT, USE EXTREME CARE TO AVOID
INJURY TO PERSONNEL AND EQUIPMENT.
Follow this procedure exactly in the order it was written. This procedure was developed with your safety in mind.
Follow this sequence to protect you and the equipment from irreparable damage.
1. Preparation:
a. Remove the front cover from the PDU (to access the breakers).
b. Remove the front cover from the OC (to access the breaker).
c. Remove the front, rear, and left side covers from the Gantry (to access the Servo amp).
d. Verify again that all breakers and switches (OC AC Box, Gantry rear base, and PDU) are OFF according to
’Checks prior to Applying Power Ground Continuity.’
e. Verify that wiring and cabling are correctly connected.
2. Switch ON the breaker on the power distribution box (hospital supply).
3. Switch ON the CB2 breaker on the PDU.
4. Verify that the power-ON lamp of the PDU is ON.
1-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
SW
PS
14
K3
K2
K1
K11
10. Push the OC power switch once. This does not turn ON the OC.
11. Verify that the voltage between terminals on TM 1 of the OC is 95135 VAC. See Illustration 1-3.
12. Switch ON the ’Slip Ring 115V’ switch at the Gantry rear base.
Verify that the x-ray generator on the rotating assembly is powered ON; this can be verified by checking that
LEDs on the XG controller boards turn ON. Also verify that the x-ray tube fan and pump start to operate.
13. Switch on the ’Rotate’ switch at the Gantry rear base.
14. Measure 180 220 VAC on the Servo Amplifier input (between N and L terminals).
15. Turn ON the breakers of the OC.
16. Install the OC, PDU, and Gantry covers.
1-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
WARNING
ROTATION HAZARD! BECAUSE OF THE CONTINUOUS ROTATION OF THE GANTRY
THERE ARE HAZARDS INVOLVED IN WORKING ON OR NEAR THE GANTRY. THE MOST
OBVIOUS HAZARD IS THE AXIAL MOTION OF THE GANTRY. THE HIGH VOLTAGE (HV)
SUBSYSTEM IS MOUNTED DIRECTLY ONTO THE GANTRY. THE HV SUBSYSTEM
CONSISTS OF COMPONENTS THAT ARE BULKY AND HEAVY. GIVE ROTATION HAZARDS
RESPECT.
1. Switch OFF the ‘Rotate’ switch at the Gantry rear base.
2. Remove all covers from the Gantry.
3. Set the safety bracket on the Gantry frame.
4. Switch ON the ’Table/Tilt’ switch.
5. Set the Service switch to ON on the SUB Board on the Gantry.
6. Rotate the Gantry manually to verify that nothing interferes the Gantry during rotation (cables, etc.).
7. Set the Service switch to OFF.
8. Switch ON the ‘Rotate’ switch.
Verify that you hear the rotation alarm sound.
9. Switch OFF the ’Power’ switch on the OC.
10. Switch ON the ’Power’ switch on the OC.
Verify that the Gantry starts to rotate, and it stops at the home position (x-ray tube at 12 o’clock position) before
making two revolutions.
1-11 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-12 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
12. Repeat steps 1. through 11. using the other Gantry emergency stop switch (one).
13. Repeat steps 1. through 11. using the OC emergency stop switch (one).
14. OC Emergency OFF test:
a. Perform the scan using the following parameters:
1.0, 1.5, or 2.0 sec /120 kV/10 mm thickness/160 mA
b. During scanning, press the OC Emergency stop switch.
c. Verify that:
• Immediately X-ray exposure stops.
• The Gantry stops to rotate within two revolutions.
15. Repeat steps 1. through 11. using the PDU emergency stop switch (one).
16. Remove all the covers from the Gantry, then repeat steps 1. through 11. using the Gantry emergency stop
switches on its frame (four).
1-13 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-14 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-15 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
Warm Up Scan
1. Make sure that nothing is in the scan area in the Gantry room.
2. Click on the ‘Tube Warm up’ icon to start the x-ray tube warm-up program.
3. Press the blinking [Start Scan] button on the OC keyboard to start the warm-up scan.
It will take approx. 1.5 minutes to complete scans.
Make sure that all warm up scans complete without error.
4. Click on [OK] button to return to the initial screen.
Scoutview Scan
5. Perform a series of scout scans to check scout scan operations:
a. Tilt the Gantry to any angle (other than 0).
b. Try to perform a scout scan. (Any scan parameters can be set.)
Make sure that the software prohibits a scout scan with the Gantry tilted.
c. Tilt the Gantry to the 0 deg. position.
d. Lay the 25 cm water phantom horizontally on the cradle.
Perform an AP (0) scout scan on the phantom.
Verify that the phantom diameter (In-Out direction) on the image is 266 mm ±3 mm.
e. Set the QA phantom on the phantom holder.
Perform an LT (90) scout scan on the phantom.
f. Use the [External landmark] button on the Gantry control panel to perform the phantom positioning so that
positioning light and center of the phantom are aligned.
g. Select [Suspension] for Autovoice.
h. Press the [External landmark] button and verify that:
• The cradle can NOT be moved.
• The cradle position is the same value as the external landmark.
i. Click on Confirm, then verify that the [Move to Scan] button blinks.
1-16 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
1-17 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 3 5116376
Axial Scan
7. Perform a series of axial scans to check axial scan operations:
a. Tilt the Gantry to the 0 deg. position.
b. Set the QA phantom on the phantom holder.
c. Use the following scan parameters: (Other parameters can be set to any value.)
Acquisition No. 1 2 3 4 5
Scan Time [sec] 1.0 1.5 2.0 3.0 5.0
1-18 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
IMPORTANT NOTE: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Use this instructions when:
• Performing the System Version-up (LFC) or Revision-up (LFW)
• Replacing the HDD with a new one (LFC)
----------------------------------------------------------------------
2-1 GENERAL
This ‘Software Loading’ describes the Load-From-Cold (LFC) procedure for a full system software loading (OS +
application) procedure (Load-From-Cold : LFC) and Load-From-Warm (LFW) procedure only for application loading
from CD-ROMs and some DVD-RAMs to the system hard disk.
CAUTION
Make sure that all Images have been reconstructed and archived on the DVD-RAM before
performing this procedure (Refer to the Operator Manual). This procedure will re-initialize
all system data disk, erasing all images and scan data.
2-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
If system version is returned to old version, the LFC procedure MUST be used. (Do NOT use
the LFW procedure.)
NOTICE
(For HP8200 Host Computer only)
Due to the unmatch issue of the low speed SCSI device DASM, if the system has a DASM
board (camera interface), disconnect the SCSI cable between the DASM and the SCSI Tower
first before loading software (OS, Application or Patch) and move the Terminator to the SCSI
Tower. After software loading, restore the connections between the DASM and the SCSI
Tower.
Procedures Prerequisite
LFC LFW
(To Be Continued)
2-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Procedures Prerequisite
LFC LFW
8 Installing the Revision-up (Patch) software
Loading Revision-up (Patch) software CD-ROM: (Patch)
software
Patch Verification -
9 Restoring the System State Data AGAIN! DVD-RAM in which
the system state data
has been saved
10 Changing System Configuration (Reconfig) -
11 Option Check
Patch Verification
12 Starting Up the System NOW! -
13 Completing the LFC / LFW Procedures
Restoring Patient Data DVD-RAMs in which
the images or raw
data have been
saved
Setting Gamma Value -
Test Scan -
14 Installing the InSite Software CD-ROM: Service
Software
2-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-2 PREPARATION
Prepare the followings before starting the LFC/LFW Procedure.
• CD-ROMs/DVD-ROMs : Core OS (OS) (for LFC Only)
• CD-ROM : Application Software
• CD-ROM : Service Software (for InSite software, if required)
• Option DVD-RAM (if new options are installed)
• 2 DVD-RAMs (Must be prepared by FE)
- For Saving System State Data (one DVD-RAM’s A side)
- For Saving Raw Data (another DVD-RAM’s A side)
Note
For the DVD-RAMs to save system state data or patient images, they do NOT need to be manually
formatted. (A used DVD-RAM is available.) This means that the format procedures will be
automatically started before saving data.
2-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
CAUTION
Make sure that all Images and raw data have been reconstructed and archived on the DVD-
RAM before performing this procedure (Refer to the Operator Manual). Both LFC and LFW
procedures will re-initialize all system data disk, erasing all images and scan data.
Prerequisite
• Two blank DVD-RAM
Note
Patient Image data and Raw data MUST be saved on the different DVD-RAMs.
Procedures
1. If required, save the Patient image on a DVD-RAM. Refer to the Operator manual. (Image Works -> Selection
(e.g. select all examination) -> Archive -> (Label) -> Save examination)
After saving image data, perform Archive -> Detach, then eject the DVD-RAM.
2. If required, save the raw data on a DVD-RAM. Refer to the Operator manual. The DVD-RAM must be initialized
first when using a new DVD-RAM. (Scan -> Scanner Utilities -> Rawdata Function -> Function Selection
-> Save to DVD-RAM -> Rawdata Selection (e.g. Whole exam) -> Start Save)
2-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
Please record camera configuration before upgrading OS system.
Prerequisite
• One blank DVD-RAM
NOTICE
For PMT-10 Tower (5270510-10), please refer to Service Note YMS-SN184 for DVD-RAM car-
tridge disassembly/Assembly procedure.
Manpower Requirements
• Approx. 10 minutes
Procedures
Before beginning the software install, save the system state data.
1. Verify that the system is powered ON.
2. Set the write protect tab of the DVD-RAM to the write position and insert the DVD-RAM into the DVD-RAM drive
of the SCSI Tower.
3. Select Service -> Utilities -> Shutdown -> Application Shutdown -> OK -> Savestate. Then click Confirm.
4. Click on Continue several times according to the messages to be displayed.
The DVD-RAM auto-format phase will be started, then the system state data are saved on the DVD-RAM.
Note
You can see the message “This is an Optical Disk containing a file system.” after clicking “Continue”
button several times. This is the last chance to cancel the procedure “Saving system state data”. If
“Continue” is clicked on this message, you can NOT cancel this procedure any more.
2-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
c. Write down the asymmetric mode (10:1, 10:2, or 6:1), then click Quit –> Quit to return to the desktop menu.
2-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
cat /usr/g/config/WLSystem.cfg
cat /usr/g/config/WLdcm.cfg
cat /usr/g/ctuser/app-defaults/network/ppsServer.map
2-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite
• CD-ROMs/DVD-ROMs: Core OS (OS)
Manpower Requirements
• Approx. 10 minutes
Procedures
NOTICE
For HPxw8000/Advantech PC, Operation Software should be loaded from DVD-ROM drive of
the host computer.
For HPxw8200/HPxw8400, Operation Software should be loaded from DVD-RAM drive in the
SCSI Tower.
Note
Confirm the proper DVD drive is the primary boot device of the OC before installing OS. The Sys-
tem BIOS configuration already set the DVD-ROM/DVD-RAM as primary boot device in factory,
there is little risk BIOS being changed during normal use.
If the system cannot be booted from the proper DVD drive, press F8 (HP8000) or F9 (HP8200/
HP8400) to set the right boot device when Boot Menu shows up just after OC is powered on.
1. Insert the CD-ROM/DVD-ROM (Core OS system software) into the DVD drive of the Host Computer.
Note
After shutting down the system, press the OC power button to restart. Insert the CD-ROM/DVD-
ROM quickly into the DVD drive, otherwise, the system can not be started from the CD-ROM/DVD-
ROM.
2. Verify that the LED of the DVD drive is ON, then OFF again.
3. System will be booted by the CD-ROM/DVD-ROM and OS installation will begin.
2-11 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-12 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite
• CD-ROM : Application Software
• For LFW ONLY:
One blank DVD-RAM (for saving the system state data)
Manpower Requirements
• Approx. 10 minutes
Procedures
2-13 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
P LE
AM
EX
Note
For the network settings, refer to the Section 2-13-1 Configuration Setup, step 8. Network Settings
Screen (a to d)
11. A time setup window will display, set the date and time of the system and click on set, the click on quit.
12. Wait for about 3 to 5 minutes, a message window will show to prompt restoring state, “Restore System State
data” (click on No if no Saved Data exist ). Click on Cancel if there is no Saved Data DVD-RAM. Go to next
step.
Click Yes if there is Saved Data DVD-RAM. A message “Insert DVD to the DVD-RAM and Press Confirm !”
appears.
Insert the DVD-RAM containing saved state and click on Confirm or click on Cancel.
13. Option will be installed automatically according to SaveState.
Note
It depends on the content of Saved Data DVD-RAM that what options will appear in the Installed
Option area.
2-14 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
15. For HPxw8400 software installation, a License Reminder window pops up: “This software has restricted ac-
cess to some service tools. This system might need a license for special access. Please contact your GE rep-
resentative for confirmation.”, then click OK.
For Advantech software installation, a License Reminder window pops up: “In order to ensure consistent
image quality, this software may contain a license authentication access system. If license authentication is
required, you will see a system prompt. Please contact your GE representative for additional assistance.”, then
click OK.
16. A message window appears. “ The system needs to be rebooted for the changes to take effect. Do you wish
to reboot now ”. Click Yes to restart .
17. End.
2-15 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
If Patch is needed, go to 2-11 to install Revision up.
NOTICE
Do not try to remove the CD-ROM at this time!!!
It MUST be removed in Section 2-9, Ejecting the CD-ROM.
2-16 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
14. A License reminder window pops up: “In order to ensure consistent image quality, this software may contain a
license authentication access system. If license authentication is required, you will see a system prompt.
Please contact your GE representative for additional assistance.”, then click OK.
15. A message window appears. “The system needs to be rebooted for the changes to take effect. Do you wish
to reboot now”. Click Yes to restart.
2-17 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-8-1-3 LFC Recovery Procedure (For Bad System Hard Disk Replacement)
1. Insert the Application CD-ROM into the drive, and the CD-ROM will be auto mounted, a dialog will be pop-up:
”Do you wish to run/mnt/cdrom/autorun?”, click on Yes.
2. A message window will appear. Two Modes are provided. Select Recovery.
3. Two minutes later, a dialog will appear:”Install Utility”, click on Load to begin loading the software.
4. After the reboot completes and the Xwindow starts, a shell window will display, wait for about 3 minutes and a
menu window of “Select Product” will appear, click on the product name to select, then click on Yes.
5. A message window will appear to prompt saving state: ”Insert DVD and press Confirm”.
a. If the SaveState DVD-RAM exists, click on Confirm, and click on OK to keep the default settings and pro-
ceed the procedure.
b. If the SaveState DVD-RAM does not exist, click on Cancel.
6. 3 to 5 minutes later, a system configuration window appears.
7. Set the Time Zone, Hardware information and Network, then press the ACCEPT button.
The following shows an example:
Time Zone:Asia/Shanghai Hardware:Ignore this step Network:Click on Network->Network on
P LE
AM
EX
Note
For the network settings, refer to the Section 2-13-1 Configuration Setup, step 8. Network Settings
Screen (a to d)
2-18 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-8-1-3 LFC Recovery Procedure (For Bad System Hard Disk Replacement)
8. A time setup window will display, set the date and time of the system and click on set, the click on quit.
9. Wait for about 3 to 5 minutes, a message window will show to prompt restoring state, “Restore System State
data (click on No if no Saved Data exist ). Click on Cancel if there is no Saved Data DVD-RAM. Go to next
step.
Click Yes if there is Saved Data DVD-RAM. A message “Insert DVD to the DVD-RAM and Press Confirm !”
appears.
Insert the DVD-RAM containing saved state and click on Confirm or click on Cancel.
10. Option will be installed automatically according to SaveState.
Note
It depents on the content of Saved Data DVD-RAM that what options will appear in the Installed
Option area.
11. Please confirm the recovery has finished before reboot, the recovery procedure will take at least 1 hour. Please
open a shell and use “cat/proc/mdstat” to check, click on Okay.
12. A message window appears:”The system needs to be rebooted for the changes to take effect. Do you wish to
reboot now”. Click Yes to restart.
13. End.
NOTICE
If Patch is needed, go to 2-11 to install Revsion up.
NOTICE
Do not try to remove the CD-ROM at this time!!!
It MUST be removed in Section 2-9, ejecting the CD-ROM.
Note
It is recommended that the FE do LFC by normal mode. Recovery mode is introduced only if the customers have
important images to be restored.
2-19 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
Do NOT click on Startup at this time!
2-20 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite:
CD-ROM Disk: DVD Interchange Software
Procedure:
1. Check Software version
a. Select shell from desktop Menu located on the upper right of the screen. Then type the following responses
to the indicated prompts.
Type: rpm -qa|grep dvd "ENTER"
b. If displayed version is earlier than version to install, uninstall the earlier version of DVD Interchange
Software by referring to "How to uninstall" (the same DVD Interchange Software Version as installed).
2. How to uninstall
NOTICE
When perform uninstallation, be sure to use the same DVD Interchange Software Version as
installed.
a. Insert the CD-ROM into the DVD-RAM drive in the SCSI Tower.
b. Application shutdown.
Note
Make sure the application has been shut down.
c. Select Linux Shell from desktop Menu located on the upper right of the screen. Then type the following
responses to the indicated prompts.
Type: su - “ENTER”
Type the root password: #bigguy and press “ENTER”
Type: cd /usr/g/ctuser/DI “ENTER”
Type: ./install -u -type be2 “ENTER”
d. Finally “uninstallation succeed” will display.
e. Type: cd ..
Type: mv DI DI.lfc
Type: exit “ENTER”
f. Close the shell.
2-21 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-22 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite
• CD-ROM : Application Revision-up (Patch) Software
Procedures
1. Insert the CD-ROM (application patch software) into the DVD-RAM/DVD-RW drive of the SCSI/Peripheral
Tower.
2. On the desktop menu, click on Install Software located on the upper right of the screen.
3. “Do you install software from CD-ROM?” window appears. Click on Yes.
4. “Following software will be installed” window appears. Click on Yes.
The patch installation procedures are automatically started.
5. Click on OK in response to “Installation Successful.” window.
Note
Some patch softwares might require reboot (shown below). If it does, when clicking on OK, the
system automatically reboots and pauses at the desktop menu.
6. After completion of the patch installation, Click on Shell on the upper right of the screen.
7. Type the following to eject the DVD-RAM.
NOTICE
Do NOT click on Startup at this time!
2-23 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite
• CD-ROM : DBPCI Tool Software VR1.0 for software VR2.19 or VR2.2x
Procedures
1. Reboot the system.
2. When "You have 5 seconds to cancel application startup......" message appears, click on Cancel.
3. Insert the CD-ROM (Patch Software) into the DVD-RAM drive.
4. Open a shell.
5. Type the following responses to the indicated prompts:
a. su -
b. #bigguy
c. mount /dev/dvd /mnt/cdrom
d. cd /mnt/cdrom/bin
e. ./installDBPCI2
6. Type the following to eject the CD-ROM when ‘installation successfully’ displays.
a. cd /
b. umount /mnt/cdrom
c. eject
d. exit
7. Shutdown to restart the system.
8. The information displays: “Set DBPCI2 finished.”.
9. End.
2-24 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
Do NOT click on Startup at this time!
2-25 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Prerequisite
• DVD-RAM (including the system state data saved in section 2-4)
Manpower Requirements
• Approx. 2 minutes
Procedures
1. In desktop menu, select Restorestate.
2. “Insert DVD and Press Confirm!” appears. Insert the DVD-RAM, including the system state data saved in
section 2-4, into the DVD-RAM drive, then click on Confirm.
3. “This is an Optical Disk containing a file system.” appears. Click on Continue.
4. “Warning: Restoring will erase the previous contents on disk.” appears. Click on Continue.
5. “System state restored successfully” appears. Click on Okay.
6. Eject the DVD-RAM from the DVD-RAM drive.
NOTICE
Do NOT click on Startup at this time!
2-26 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Manpower Requirements
• Approx. 15 minutes
1. In desktop menu, click on Reconfig located on the upper right of the screen.
This System configuration screen appears.
2. Enter the appropriate configuration data.
NOTICE
The following items restrict the use of characters for entry. Do NOT use other characters.
2-27 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Time Zone
2-28 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-29 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Auto mA modes
IQ
Normal High mA (High IQ)
SD1 IQ
Low Dose
SD2 Normal
IQ
Low Dose
Normal
SD3 Low Dose
Target SD IQ Level
SD IQ 1.63
SD Normal 1.47
- 1.40
- 1.26
- 1.22
- 1.14
- 1.10
- 1.0
2-30 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Mode Meanings
10:1 Provides 10 mm and 1 mm slices.
10:2 Provides 10 mm and 2 mm slices.
6:1 Provides 6 mm and 1 mm slices.
2-31 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-32 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-33 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
For system state restore, camera configuration of CTT4.5.1 system can not be restored in
CTT6.2.9 system. After LFC, camera reconfiguration is needed.
a. Select either Laser Camera or DICOM Printer.
2-34 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-35 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Note
For a summery of troubleshooting information for DICOM Print, refer to Appendix, 2-18-2
DICOM Print Troubleshooting Tips.
• Add: used when adding the DICOM printer newly to the system.
• Delete: used when deleting the DICOM printer selected from the Device File list.
• Update: used when modifying the setting for the DICOM printer selected from the Device File list.
a. Click on Add.
2-36 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
b. Set the following parameters, then click on Advanced. This goes to 2nd setting screen (for setting advanced
parameters) for DICOM Print Camera (step c).
2-37 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
• Network Parameters :
Enter the hospital provided Filming Device Name, same as Host Name (Name shown in the header title
of the Film composer).
Enter the hospital provided Filming Device Host Name.
Enter the hospital provided Filming Device IP Address.
Enter the AE title from the DICOM Conformance Statement document provided with the Filming Device.
Enter the TCP Listen Port from the DICOM Conformance Statement document provided with the
Filming Device.
2-38 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
When, at the DICOM Print Camera side, you enter the AE title of a CT system connected to
2-39 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-40 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Maximum Density
Minimum Density
• Smoothing Type:
This parameter is used when the Magnification Type is set to CUBIC. The parameter represents the
coefficient for the image resolution algorithm and is Filming Device manufacturer dependent and must
be verified with the radiology department after filming review.
2-41 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-42 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
IMPORTANT NOTE: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Once you have clicked on Accept, all of the remote printers that a customer has set
individually will be changed to the printer selected at AutoFilm Setting. This can NOT be
reset to the previous printers.
b. Click on Accept.
c. On the Camera Setting screen, select Quit. Then go to Network Setting Screen.
2-43 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
P LE
AM
EX
GATEWAR
IP Address
IP Address
Host Name CT
2-44 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-45 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-46 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
When performing Application-Shutdown and then restarting the system, always use the
Shutdown button. Do not use the Startup Button, because this might not work correctly.
2. Verify that the system starts up with no error.
3. Confirm that the latest version of software has been installed in the system. The system version is displayed
at the lower right of the screen while the system is starting up.
4. Click on OK in Attention window.
2-47 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
% su <Enter>
2-48 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-17-1 General
Prerequisite
• The modem must be powered up.
• Prepare the followings before starting the InSite Installation Procedure.
CD-ROM : Service Software (Must be prepared by FE, distributed through TAB 261, TAB 263).
- TAB 261:
For OS CTT1.8.12 (P/N: 5120769), InSite software V/R3.20 (P/N: 2404035)
- TAB 263:
For OS CTT4.5.1 (P/N: 5144980), CTT6.2.9 (P/N: 5265479) and CTT6.3.11 (P/N: 5405599), In-
Site software V/R3.52 (P/N: 5150686)
Manpower Requirements
• Approx. 30 minutes
2-49 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
9. On the desktop menu, click on Install InSite button located on the upper right of the screen.
A few seconds later, the InSite Interactive Platform Configuration screen appears.
2-50 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
After entering InSite Setup Screen, call the local support center to set up the InSite together.
GEMS - Americas GEMS - Europe GEMS - Asia
CT National Support Center European Support Center Asia Support Center
Phone: 1-800-321-7937 (33) 1 3083 1300 On-Line-Center
FAX: (262) 896-2710 (33) 1 3070 9970
11. After a moment, the InSite Setup Screen appears.
Click on InSite Checkout tag.
2-51 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
VERY IMPORTANT: You MUST run the checkout in order to establish the InSite connection.
Checkout MUST be rerun in the event of a system re-load.
1. The InSite Checkout Screen appears.
Click on CHECKOUT NOW.
DISABLE INSITE
2-52 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
----------------------------------------------------------------------
5. When the checkout process has been completed successfully, you might get some messages such as “InSite
Dial out Check completed Successfully” from a local support center.
2-53 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
DISABLE INSITE
2-54 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NOTICE
When performing Application-Shutdown and then restarting the system, always use the
Shutdown button. Do not use the Startup Button, because this might not work correctly.
8. Verify that the system starts up with no error.
2-55 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-56 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
NEED TO PREVENT DICOM PRINT ATTRIBUTES FROM BEING SENT TO DICOM PRINT CAMERA
• Symptom: Some DICOM Print attributes are optional, and may result in fatal errors. For example, the
Fuji camera does not support the Empty Image Density parameter for the film box.
• Solution: Using your favorite editor, add the following line(s) to the camera.dev file located in ‘~ctuser/
app-defaults/devices‘ after the DICOM Print device has been otherwise configured.
- To prevent sending the Smoothing Parameter set FB_Smooth FALSE
- To prevent sending the Border Density set FB_Border FALSE
- To prevent sending the Empty Image Density set FB_EID FALSE
- To prevent sending the Minimum Density set FB_MinD FALSE
- To prevent sending the Trim Parameter set FB_Trim FALSE
2-57 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-58 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
2-19 APPENDIX
2. Determine Machine # in accordance with the table below and enter it into Machine # in the system setting
screen.
For the example above, ‘26010‘ must be entered as a Machine #.
2-59 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 19 5116376
Autofilm Setup
Destination
Laser Camera
Yes Yes
Scout XRef–Scout
Film Direction
Top to Bottom
e/s/i Yes
Changed
OK Cancel
NOT Changed
Film Tab Card
Scan Timing Recon Film
2-60 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
NOTICE
Software V/R3.20 or later. (The detailed information refers to Diagnostics System Ser-
vice Tool CALIBRATION/ALIGNMENT ACCESS RESTRICTION.
For Calibration/Alignment access restricted sites, please get a “password” through the ded-
icated Intranet or the Service Call center before doing Alignment/Calibration (a pop-window
will provide a “key” that is needed to generate the password). The access will be granted
for 48 hours.
For access free sites (decided by local service businesses), please get a “license” through
the dedicated Intranet or the Service Call center after software load (a pop-window will pro-
vide a “key” that is needed to generate this License). No password is needed to access Cal-
ibration/Alignment since then.
3-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-1 GENERAL
This ‘X-ray Alignment’ consists of the following check/adjustment procedures and must be performed in this order.
3-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
WARNING
ROTATION HAZARD !
IN THIS ‘X-RAY ALIGNMENT’, GANTRY COMPONENTS ARE ADJUSTED AND SCANS ARE
PERFORMED. ALWAYS SWITCH OFF THE ‘ROTATE’ SWITCH BEFORE SERVICING OR
ADJUSTING THE GANTRY. ALSO VERIFY THAT NO PEOPLE ARE IN THE SCAN ROOM
WHENEVER A SCAN IS PERFORMED.
Requirements
The critical components for X-ray Alignment are all mounted directly to the rotating Gantry; they are:
• X-ray tube
• Collimator (includes a bow-tie filter and an adjustable beam defining exit slit)
• Detector
Tools and materials required for x-ray alignment:
• Detector alignment tool (shipped with the system)
• Aperture alignment tool (shipped with the system)
• G-SAG pin (attached on the bottom of the collimator)
3-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Gantry Geometry
Gantry geometrical direction definitions:
THETA THETA
3-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Special Equipment
• Detector Alignment Tool (Shipped with the system)
1. Preparation:
3-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Special Equipment
• Aperture Alignment Tool (Shipped with the system)
1. Preparation:
3-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-11 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
2 7
PUSH 6
5 4
3-12 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
IMPORTANT NOTE: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Do not remove the bow–tie filter during POR for the Twin System.
------------------------------------------------------------------------
1. Preparation:
a. Switch OFF the “Rotate” switch.
b. Remove the front, right side, and left maintenance covers.
c. Switch ON the “Rotate” switch.
NOTICE
The detector temperature must be at a specified temperature before alignment, otherwise
alignment result is not exact.
2. Select Service –> Calibration –> Automated Alignment –> POR Alignment.
3. Click on OK to enter the POR program.
4. Click on Confirm to enter warm up scan sequence.
5. Click on Confirm in the Service Scan Window.
The warm up scans start, then air scans automatically start.
6. The tube travel appears on the screen. If the following message appears, you can complete the POR proce-
dures.
******************************* Displayed *******************************
Tube is Aligned within tolerance.
For Accuracy
Move Tube x.xxx mm (x.xxxx inch) FWD.
***************************************************************************
7. Adjust the tube Z-Axis position:
a. Rotate the Gantry (Tube) to the 12 o’clock (home) position.
b. Switch OFF the “Rotate” and “XG Power” switches.
c. Loosen the 4 mounting bolts and 2 support bolts. (See Illustration 3-3)
d. Locate the Adjustment Nuts for Z-Axis; note that there are two Z-Axis nuts for adjustment. (See Illustration
3-3)
e. Loosen the nut that faces the direction in which you want to shift the tube.
f. Adjust the x-ray tube position by turning the adjustment nuts by the amount instructed on the monitor
screen.
g. Tighten the nut previously loosened in step e.
h. Tighten the 4 mounting bolts and 2 support bolts. (Torque: 280 kgf.cm)
3-13 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Z-
Ax
is
Support Bolt
Adjustment Nut for Z-Axis
RIGHT REAR
FRONT
LEFT
Note: When loosen respective adjustment nut, use two spanner. One spanner
holds one nut, the other one loosens another nut. This will avoid damaging the
adjustment screws when adjusting the position of the nut. Please refer to above photo.
Note:
One turn = 1 mm shift.
3-14 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
NOTICE
The detector temperature must be at a specified temperature before alignment, otherwise
alignment result is not exact.
2. Select Service –> Calibration –> Automated Alignment –> BOW alignment.
3. Click on OK to enter the BOW program.
4. Click on Confirm to enter warm up scan sequence.
5. Click on Confirm in the Service Scan Window.
The warm up scans start, then air scans automatically start.
6. The detector travel appears on the screen. If the following message appears, you can complete the BOW pro-
cedures.
******************************* Displayed *******************************
Detector is Aligned within tolerance.
***************************************************************************
7. Adjust the Detector Z-Axis position:
a. Check that the Gantry is at the home position.
b. Switch OFF the “Rotate” switch.
c. Remove the flexible cable cover. (See Illustration 3-4)
d. Loosen the three locking screws (Allen cap head).
3-15 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Locking Screw
(Allen Head)
Z-Axis
Flexible Cable Cover Detector Adjustment Nut
Locking Screw
(Allen Head)
Z-Axis
Adjustment Nut
Detector
Support Plate Detector
Pin
Detector Detector
Support Plate
e. Adjust the Detector position by turning the adjustment nut(s) by the amount instructed on the monitor
screen.
Formula: x.xxxx mm / 0.75mm = xx turn of adjustment nut (one turn: approximately 0.75mm shift)
Counterclockwise; FWD, toward the Table
Clockwise; BWD, away from the Table
Specification : Detector Left, less than 0.072 mm
Detector Center, less than 0.076 mm
Detector Right, less than 0.072 mm
f. Tighten the three locking screws.
Torque: 117kgf.cm (11Nm)
g. Switch ON the “Rotate” switch.
h. Return to step 2.
8. Proceed to ‘Qcal Channel Ratio’ .
3-16 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-17 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
SAG Pin
3-18 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-19 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Adjust
X-ray
Tube
Focus
Center of FOV
CH1
Detector
Center Channel:
342.75 + 0.02 CH
Note
Within the ‘Automated Alignment’ menu (Service Calibration Automated Alignment), you do
not have to perform the following menus:
‘Tube Rough ISO Alignment’
‘Radial Alignment’
These are performed at the GEHW factory only.
1. Preparation:
You do not have to perform the following, if you have just completed the ‘Detector Beam-on-Window’ or ‘Gravity
SAG’ procedure.
a. Switch OFF the ‘Rotate’ switch.
b. Remove the Gantry front and both side covers.
c. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual)
d. Switch ON the ‘Rotate’ switch.
3-20 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Screw Driver
50mm
Phantom Holder
x
ISO Center
3-21 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-22 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Procedures
This ‘Filter Center Alignment’ aligns the filter to the x-ray tube and the Detector.
X-ray (Fixed)
Tube
Focus
Center of Filter
Adjust
Filter
Ch1
Detector (Fixed)
1. Preparation:
You do not have to perform the following, if you have just completed the ‘Iso Center Alignment’ procedure.
a. Switch OFF the ‘Rotate’ switch.
b. Remove the Gantry front and both side covers.
c. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual)
d. Switch ON the ‘Rotate’ switch.
3-23 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
3-24 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Prerequisite
• Radial Alignment Tool : 2234059
1. Preparation:
a. Switch OFF the ‘Rotate‘ switch.
b. Remove the Gantry front and both side covers.
c. Rotate the Gantry (Tube) to the 12 o‘clock (home) position.
d. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual)
e. Remove the connector cover from the DAS assy.
f. Switch ON the ‘Rotate‘ switch.
2. Select Radial Alignment, refer to below:
3-25 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
A'
3. Check that an average of the 2 calculated Radial Alignment data is within a specification.
If not, perform the following steps:
a. Switch OFF the ‘Rotate‘ switch.
b. Remove the Radial Alignment tool.
c. Install a Dial Indicator on the side of the Detector using an attachment tool.
d. Loosen the three (x2) mounting screws and a locking screw.
e. Refer to the average value, rotate the Detector in the specified distance and direction.
f. Tighten the mounting screws and the locking screw.
• Locking Screw Torque: 11 Nm (117 kgfcm)
g. Remove the Dial Indicator with attachment tool.
h. Switch ON the ‘Rotate‘ switch.
i. Repeat the Radial Alignment procedure, to verify the adjustment.
3-26 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 15 5116376
Mounting
Screws
Mounting
Screws
Dial Indicator
Locking Screw
Detector
Attachment Tool
3-27 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
3-28 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Software V/R3.20 or later. (The detailed information refers to Diagnostics System Ser-
vice Tool CALIBRATION/ALIGNMENT ACCESS RESTRICTION.
For Calibration/Alignment access restricted sites, please get a “password” through the ded-
icated Intranet or the Service Call center before doing Alignment/Calibration (a pop-window
will provide a “key” that is needed to generate the password). The access will be granted
for 48 hours.
For access free sites (decided by local service businesses), please get a “license” through
the dedicated Intranet or the Service Call center after software load (a pop-window will pro-
vide a “key” that is needed to generate this License). No password is needed to access Cal-
ibration/Alignment since then.
4-1 GENERAL
NOTICE
If customer has the asymmetric scan option, please confirm it was installed before system
calibration, otherwise redo system calibration.
This ‘System Calibration’ describes the following check/calibrations/adjustment:
• Converter Amplifier Linearity Check (by performing x-ray exposures)
• Hilight Calibration; consisting of the following:
Q Calibration (Q-cal)
XT Calibration (XT-cal)
AV Calibration (AV-cal)
DG Calibration (DG-cal)
• Air and Phantom Calibrations
• CT Number Adjustment
The above calibrations and adjustment should be performed if any of the following replacements and/or system
adjustments are performed since the last calibrations/adjustment.
‘Converter Amplifier Linearity Check’ may be performed before calibrations/adjustment.
• X-ray tube replacement
• Detector replacement
• DAS or Converter Board replacement
• Collimator or Filter replacement
• Plane of rotation alignment
• Detector beam-on-window alignment
4-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
The following table shows that which Hilight calibration (Q-cal, XT-cal, AV-cal, or DG-cal) should be performed for
the above occasions and also the calibration/adjustment order to be followed.
4-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Required Phantoms
Use the following phantoms (furnished with each system) during system calibrations/adjustment.
Make sure they are clean and contrast-free.
QA Phantom XT Phantom
Diameter : 12.6 cm
(Polypropylene)
4-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
4-2-1 General
This Hilight calibration should be performed prior to the air and phantom calibrations; and the air and phantom
calibrations should be performed if once the Hilight calibration is performed.
The x-ray tube must be sufficiently cool (the tube case temperature must be below 10 % heat level).
WARNING
ROTATION HAZARDS! SOME HILIGHT CALIBRATIONS ROTATE THE GANTRY (SEE THE
TABLE BELOW). WHEN HILIGHT CALIBRATION IS PERFORMED WITHOUT THE GANTRY
COVERS INSTALLED, ALWAYS MAKE SURE THAT NO PERSON IS IN THE SCAN ROOM.
4-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
4-2-2 Q Calibration
The focus position of the x-ray tube shifts with temperature change. It will consequently shift the x-ray beam position
along the Z-axis. In this calibration, the following scans are automatically performed:
• four scans (Thickness: 1, 2, 3, 5, and 10 mm) (when the x-ray tube is cold)
• warm-up scans
• four scans (Thickness: 1, 2, 3, 5, and 10 mm) (when the x-ray tube is hot)
This calibration takes approximately 10 minutes.
1. Preparation:
a. Switch OFF the “Rotate” switch.
b. Remove the gantry front cover.
Note
4-2-3 XT Calibration
The Lumex crystals of the detector cells generate light when they are hit by x-rays. Since the crystals are placed
close to the crystals of the adjacent channels, the light from one channel can interfere with adjacent channels,
causing crosstalk noise. This procedure creates a calibration file to compensate this interference.
This calibration takes approximately 15 minutes.
1. Preparation:
a. Switch OFF the “Rotate” switch.
b. Remove the gantry front cover.
c. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual.)
d. Switch ON the “Rotate” switch.
2. Select XT-CAL; refer to below:
4-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
WARNING
ROTATION HAZARDS! WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON
AND SMALL BUTTON), THE GANTRY QUICKLY ROTATES TO THE 0 POSITION. IF IT IS
NECESSARY TO PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY,
SWITCH OFF THE ‘SCAN’ SWITCH FIRST.
4. Position the XT phantom at the (scan center + 180 mm) height:
a. Install the XT phantom to the phantom holder.
b. Shift the phantom to the up-limit, using the up-down adjuster.
c. Position the phantom at the scan center; align the positioning lights and a cross marked on the phantom
surface.
d. Hold down the [Height] button to display the current height (ex. ‘-198’), and press the [Up] button to raise
the Table by 180 mm (ex. Until the Display reads ‘-018’).
If the Table can not be raised to the specified height due to the interlock function, switch ON (up) the T3
Table dip switch on the TGP Board to disable the interlock function, and continue to raise the Table. In this
case, be careful not to have the Table collide against anything.
e. Select [Confirm] on the screen.
Positioning
Lights
Up/Down Adjuster
4-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Do not forget to switch OFF the T3 Table dip switch (if it is set to ON), otherwise there will
be collision hazard, since the interlock function does not work, if T3 is set to ON.
4-2-4 AV Calibration
The light emission of the Lumex Crystal persists after the x-ray radiation stops. This phenomenon is called ‘After
Glow.’ This procedure creates a file called After Glow Vector, used to compensate the After Glow.
This calibration takes approximately 2 minutes.
1. Preparation:
a. Switch OFF the “Rotate” switch.
b. Remove the gantry front cover.
c. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual.)
d. Switch ON the “Rotate” switch.
2. Select AV-CAL; refer to below:
4-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
4-2-5 DG Calibration
If some scans are performed with the same conditions but with different scan times, the CT numbers may not be the
same for these scans. This is due to Converter Board gain changes caused by different scan times. The DG
calibration reduces the CT number changes.
This calibration takes approximately 3 minutes.
1. Preparation:
a. Switch OFF the “Rotate” switch.
b. Remove the gantry front cover.
c. Remove the bow-tie filter from the collimator. (Refer to the Component Replacement manual.)
d. Switch ON the “Rotate” switch.
2. Select DG-CAL; refer to below:
4-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Precondition
• The bow-tie filter should be installed.
1. Select Service Adjustment from the Service menu.
2. Select Service Calibration from the Service Adjustment.
3. Select Auto Sequence 1 (Air Cal Phantom Cal) from the Service Calibration menu.
4. Select [Confirm] on the screen to select all the calibration stations.
5. Follow the instructions displayed on the monitor screen.
6. Proceed to the ‘CT Number Adjustment’ procedure.
4-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
If you do not click on Confirm in the scan confirm screen within 15 minutes, Time- out occures.
3. Verify that the water CT # and air CT # equal 0 ±3 and -1000 ±5 respectively.
Note
For the system with the asymmetric option only, the CT # value displayed is the original one. Note that the updated
data is NOT displayed.
4-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 9 5116376
5-1 GENERAL
This ‘Image Performance Verification’ contains tables of scan techniques and specifications for evaluating image
performance.
General Requirements
Perform the following before continuing:
1. Verify that system calibration (Hilight calibration, air and phantom calibrations, and CT Number Adjustment)
has been completed.
All image performance scans must use calibration data that are less than eight hours old.
2. Warm up the system at least two hours (minimum) prior to data collection.
Required Phantoms
Use the following phantoms (furnished with each system) during image performance verification.
Make sure they are clean and contrast-free.
• Water Phantom (25 cm)
• Polypropylene (PP) Phantom (42 cm)
• Quality Assurance (QA) Phantom
5-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 9 5116376
High Contrast Spatial Resolution and Artifact Check Using QA (Quality Assurance) Phantom
3. The 1.0 mm pattern (see Illustration 5-2) must be clearly visible by the following techniques:
Table 5-1
5-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 9 5116376
+Y ROI Circle
(Area of 674.11 mm2 or 1994.30 mm2)
Image
-X +X
Mc (0.0 cm)
Mo (10.0 cm)
SD (0.0 cm)
-Y
1.0 mm Pattern
5-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 9 5116376
5-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
25 cm WTR Large 120 1.5 200 7 2i 02 < 5.0 02 < 5.0 5 1 ±0.1
25 cm WTR Large 140 1.5 120 10 2i 02 02 5
25 cm WTR Small 120 1.5 140 10 2i 02 < 5.5 02 < 5.5 5 1 ±0.1
25 cm WTR Small 120 1.5 140 10 1i 02 < 5.5
5-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
Table 5-2 Image Performance Check (For HiSpeed Dual_Big OC) (Continued)
5-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
25 cm WTR Large 120 2 150 7 2i 02 < 5.0 02 < 5.0 5 1 0.1
25 cm WTR Large 140 2 80 10 2i 02 02 5
25 cm WTR Small 120 2 100 10 2i 02 < 5.5 02 < 5.5 5 1 0.1
25 cm WTR Small 120 2 100 10 1i 02 < 5.5
5-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
Table 5-3 Image Performance Check (For ProSpeed FII_Small OC 30KVA) (Continued)
5-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
25 cm WTR Large 120 1.5 200 7 2i 02 < 5.0 02 < 5.0 5 1 ±0.1
25 cm WTR Large 140 1 160 10 2i 02 02 5
25 cm WTR Small 120 1 200 10 2i 02 < 5.5 02 < 5.5 5 1 ±0.1
25 cm WTR Small 120 1 200 10 1i 02 < 5.5
5-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
Table 5-4 Image Performance Check (For ProSpeed FII_Small OC 40KVA) (Continued)
5-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
WARNING
POTENTIAL FOR SHOCK.
GROUND WIRES WILL HAVE GROUND CURRENT PRESENT WITH POWER “ON”. FOLLOW
APPROPRIATE SAFETY PROCEDURES FOR WORKING WITH AN ENERGIZED SYSTEM.
NOTICE
Follow ALL required safety and PPE procedures customary for your organization, when
working on this product.
Item Qty
Standard service tool kit 1
Dale 600/601 Meter (from tool pool)* 1
Dale extended length leads* 1
*: GE Healthcare performed validation of this procedure using the Dale 600/601
meter ONLY. Due to the unique nature of this meter, GE cannot guarantee the
accuracy of this procedure if you use another meter.
6-1 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
6' (1.9m)
6'
(1
.9
m
)
(1
.9
m
6' (1
6-2 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
6-1-5 Procedure
Illustration 6-1 Using the Dale 600/601 Meter to Measure Leakage Current
6-3 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
NOTICE
Beware of static discharge from the scan window, keypads, display, touch pads, and other
plastic surfaces.
5. Record the results of your tests in Table 6-1, making certain that no leakage current exceeds the following lim-
its:
6-4 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
6. Re-install the Table Front Bottom Cover and the Gantry Left Side Cover.
Procedure Hints
• Items with abnormally high or low measurements could indicate improper wiring, or loose or poor con-
nections due to corrosion, painted surfaces, etc.
• High leakage could indicate a wiring error such as a neutral connected to the ground.
• Fluctuating ground currents could indicate a short, poor connection, or facilities ground.
• Refer to the Illustration below for visual depictions of the required measurements.
7’
7’
7’
7’
6’
6’
6’
6’
6-5 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
DANGER
POTENTIAL FOR ELECTRIC SHOCK.
SERVICING HARDWARE WITH POWER “ON”.
EQUIPMENT SERVICE CAN ONLY BE PERFORMED SAFETY WITH THE MAIN
POWER “DISCONNECT” TAGGED AND LOCKED OUT.
Item Qty
Standard service tool kit 1
Dale 600/601 Leakage Current Meter 1
GEH LOTO Kit 1
*: GE Healthcare performed validation of this procedure using the Dale 600/601
meter ONLY. Due to the unique nature of this meter, GE cannot guarantee the
accuracy of this procedure if you use another meter.
6-6 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
6-2-5 PROCEDURE
NOTICE
Follow LOTO and other safety procedures found in this manual before starting this proce-
dure.
6-7 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
NOTICE
The measured leakage current must not exceed 5 mA in any ground wire.
6-8 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
Where Installed
City State
Customer's Telephone Number Room No.
System ID # GON #
DVM Serial # Cal Due Date
Leakage Meter Manufacturer Model #
Serial # Cal Due Date
Installer’s Name: Company
This system was tested in accordance with NFPA 99: Standard for Health Care Facilities.
The measured leakage current must not exceed 5 MA in any ground wire.
Table Ground Bus Results Test Date Tester
This system was tested in accordance with NFPA 99 Sections 8.4.1.3.4.1, and 8.4.1.3.4.2:
Standard for Health Care Facilities.
6-9 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 12 5116376
6-10 SYSTEM
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 11 5116376
OPERATOR CONSOLE
TABLE OF CONTENTS
SECTION PAGE
i OPERATOR CONSOLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
ii OPERATOR CONSOLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 11 5116376
SECTION 1 - OC COMPONENTS
Ground Connection
If this is the first time to check the OC power supplies after system installation, preform this ‘Ground Connection’
check.
3. Check the ground connection of the power supplies as follows (see illustration 1-1):
Note
When you adjust power supply potentiometers, slowly turn them; otherwise, power supply built-in
protector will shut themselves down. If this happens, switch OFF the Operator Console, wait
approximately a few minutes, and switch ON the Console.
a. Connect a digital multimeter between the OC ground stud and ground (FG Ground) on power supplies.
(Multimeter: resistance measure mode)
b. Verify that the resistance reads less than 0.2 ohms. If resistance exceeds the above value, tighten, clean
or re-crimp connections, and measure again.
c. Perform the above check on the other power supplies.
+12V Power
-12V Power Supply
Supply
+5V Power
Supply
+12V Power
Supply
+5V Power
Supply
+5V
+12V
-12V
Voltage Check
The System Disk and the Raw Data Disk are powered by the inbuilt Host PC ATX Power Supply.
4. Check the output of the +5 VDC power supply as follows:
a. Switch ON the Operator Console
b. Connect a digital multimeter at the terminal strip (J16) on the NPD assy (Multimeter: voltage measure mode)
(see illustration 1-2).
c. Measure the voltage and check that it is within +5.00 VDC ∼ +5.10 VDC. If it falls outside these limits, adjust
it by turning the potentiometer (see illustration 1-1).
d. Connect an oscilloscope to the same points as above.
e. Observe the voltage and check that the ripple is less than 200mVp-p. If it falls outside this range, replace
the power supply.
5. Check the output of the +12 VDC power supply as follows:
a. Connect a digital multimeter at the terminal strip (J17) on the NPD assy (Multimeter: voltage measure mode)
(see illustration 1-2).
b. Measure the voltage and check that it is within +11.76 VDC ∼ +12.24 VDC. If it falls outside these limits,
adjust it by turning the potentiometer (see illustration 1-1).
c. Connect an oscilloscope to the same points as above.
d. Observe the voltage and check that the ripple is less than 100mVp-p. If it falls outside this range, replace
the power supply.
6. Check the output of the -12 VDC power supply as follows:
a. Connect a digital multimeter at the terminal strip (J15) on the NPD assy (Multimeter: voltage measure mode)
(see illustration 1-2).
b. Measure the voltage and check that it is within -11.76 VDC ∼ -12.24 VDC. If it falls outside these limits,
adjust it by turning the potentiometer (see illustration 1-1).
c. Connect an oscilloscope to the same points as above.
d. Observe the voltage and check that the ripple is less than 100mVp-p. If it falls outside this range, replace
the power supply.
1-2 FANS
1. Turn OFF the OC main power.
2. Remove the following covers:
• OC Front Cover
• Rear Cover
3. Using a flashlight, or by feeling for the proper airflow, check that the FAN is operating normally.
If any fan is defective, replace the unit.
Front View
FANs
Rear View
FANs (x2)
FANs
Right View
Air Flow
Air Flow
SECTION 2 - OC OPERATION
WARNING
ELECTRICAL SHOCK HAZARD !
IF THE SYSTEM HAS UPS ASSY, MAKE SURE YOU TURN OFF THE UPS POWER BEFORE
YOU ACCESS THE OPERATOR CONSOLE.
NOTICE
When the interactive test or off-line test is completed, the system MUST be powered OFF
([Exit] -> [OK]) to avoid accidental X-ray Exposure. That is because system reboot can NOT
activate the system reset line.
• [Startup] : The error is skipped and the power-on sequence proceeds so that the start-up screen will be
shown on the CRT monitor.
Note
When the start-up screen does NOT appear even if using the [Startup] command, the system must
be shutdown using [shutdown] button in the desktop menu.
• [Shutdown] : The system runs the shutdown sequence, resulting in the system powered OFF
automatically.
Color
3. Click on any color key (RED, GREEN, BLUE, WHITE, or BLACK).
The display color changes in the selected one.
4. Verify that no hole exits on the monitor display.
5. To exit from this test, press the left button of the mouse.
This operation returns to the monitor test screen.
Display Pattern
6. Click on any pattern key (Flat, Horizontal Gradation 1 or 2, or Vertical Gradation 1 or 2), then click on any color
key.
The display pattern changes in the selected one.
7. Adjust position, size, trapezoid, or parallelogram of the monitor.
(For adjustment, refer to Installation, Wiring and Power-ON.)
8. To exit from this test, press the left button of the mouse.
This operation returns to the monitor test screen.
Input Test
This test sends command from the keyboard to the screen (system).
3. Press any key on the keyboard.
4. Verify that the key on the screen related to the pressed key is highlighted.
OC Speaker - Alert
11. Click on [ON] button once. Verify that alert sounds once.
12. Move the [Width] and [Freq] (Frequency) slider for Alert so that sound varies.
13. Move the L and R volume sliders for Alert so that sound will become loud or faint.
Hardware Inventory
This program shows the hardware configuration of the Host Computer. This program runs “lhinv” command.
Note
When changing the hardware configuration (e.g. Memory addition, Disk change...), always run this
program to check if the system properly recognizes the hardware to be changed.
3. Click on [Hardware Inventory] from the Misc test selection window.
The list of hardware connected to the host computer appear.
4. Click on [Close] to return to the Misc test selection window.
SCSI Test
This program runs DVD-RAM access test, MOD (Option) access test, and DASM access test so that their results
will be displayed.
Note
SCSI information can be known by the hardware inventory test, but this SCSI test will give you more
detailed information.
Note
For Option Image disk, this SCSI test will be skipped, so that this result is NOT displayed.
5. Click on [SCSI Test] from the Misc test selection window.
The result of their tests appear.
6. Click on [Close] to return to the Misc test selection window.
View SYSLOG
This program displays system log information after last reboot.
7. Click on [View SYSLOG] from the Misc test selection window.
The system log information appears.
8. Click on [Close] to return to the Misc test selection window.
Note
The system log to be displayed shows only a day’s worth of log after last reboot. When the following
day comes, the log of the day before is saved on “SYSLOG.0” file, then it will be deleted from the
SYSLOG viewing window.
Note
8 day’s worth of log files are being saved as a backup on the directory “/var/log”. You can see them
using “ls” and “cat” commands. The log name is “boot.log”.
Connectivity Test
Safety Loop
This program can switch ON or OFF the relay for safety loop of the OC.
9. Click on [Safety Loop] from the Misc test selection window.
10. The message screen appears. Click on [OK] button.
The safety loop relay of the OC is in close position, so that OC safety loop is connected and the selector is ON.
11. Click on [Safety Loop] again to open the safety loop relay of the OC.
NOTICE
Before starting other test, the safety loop MUST return to the default setting. (The OC relay
is OPEN.)
12. Click on [Close] to return to the Misc test selection window.
Shutdown
This program shutdown the system.
13. Click on [Shutdown Test] from the Misc test selection window.
The system runs shutdown sequence automatically, then the system is down.
Note
If either of the relay of the front panel or DBPCI board is faulty, the system can NOT shut down.
GANTRY
TABLE OF CONTENTS
SECTION PAGE
i GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 9 5116376
TABLE OF CONTENTS
SECTION PAGE
ii GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
TP2
TP5
PS1 TP4
PS1/PS2
TGP BOARD TP6
TP7
TP2
1-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
1 4 7
0V_A 2 5 8 0V_L
3 6 9 0V_A 1106
1107
GND 1108
-5V_A -12V_A Nut(x4)
DAS POWER CABLE CONNECTOR
1-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
1-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
Nut (x6)
5V 24V RTN
3 6 9 12
+5V_A 5V_L
RF Power Cable
1 4 7 0V
1-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
1-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
1-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
Understand and follow the Safety Guidelines Manual.
1. Preparation:
a. Switch OFF the ‘Rotate’, ‘XG Power’ and ‘Slip Ring’ switches at the Gantry rear Base.
b. Remove the front, right side, and left side covers of the Gantry.
c. Switch ON the Service Switch on the SUB board near the TGP board.
2. Verify that the clearance between each rotating component part and all fixed parts is more than 10mm, while
rotating the Gantry in the CW direction by hand.
3. Check to make sure that the cables does not catch on any stationary components during each revolution.
2-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• Spring Balance (Fish Scale)
WARNING
MECHANICAL HAZARD!
FAILURE TO HOLD THE GANTRY USING THE AZIMUTH LOCK PIN PRIOR TO REMOVING
COMPONENTS MAY LEAD TO GANTRY MOTION WHICH CAN STRIKE A PERSON CAUSING
INJURY OR DEATH.
Understand and follow the Safety Guidelines Manual.
1. Preparation:
a. Switch OFF the ‘Rotate’, ‘XG Power’ and ‘Slip Ring’ switches at the Gantry rear base.
b. Remove the front, right side, and left side covers of the Gantry.
Side Weight
(0.5kg)
DAS Assy
2-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
CCW CW CCW CW
Main Weight
Side Weight
Main Weight
Side Weight
2-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
F2
F3
2-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Photo Sensor
Plate (G. Pulse 1) - Stationary Side LED
TGP BOARD
Emergency Reset RESET
(EMRG RESET)
TEST1
TEST2
2-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
(SIDE VIEW)
Photo Sensor
Plate
6mm + 0.5mm
H
A
Photo Sensor
(G. Pulse 2)
(Rotational)
2-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Over tension. After part A and part B are just touching, do not rotate the adjusting bolt;
otherwise, this will cause over tension and will shorten the life of the axial drive belt.
c. Turn the adjusting bolt in the CW direction until part A and part B are just touching.
d. Tighten the set nut.
e. Tighten the three mounting plate bolts.
4. Install the Axial Motor Pulley cover.
5. Restore the Gantry to original configuration.
2-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Set Nut
D
Spring
Adjusting Bolt
Axial
Belt
Mounting
Plate Bolts
Mounting Plate
Axial Motor Pulley
2-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• Alignment Tool
Understand and follow the Safety Guidelines Manual.
NOTICE
HSDCD Receiver and Antenna are static sensitives. Before touching the components, attach
the wrist strap to your wrist and to the metal part of the chassis.
1. Preparation:
a. Switch OFF the ‘Rotate‘, ‘XG Power‘ and ‘Slip Ring‘ switches at the Gantry rear base.
b. Remove the Gantry rear and left maintenance covers.
2. Remove the HSDCD Receiver Cover.
3. Remove the Slip Ring Covers.
4. Disconnect the RF cables.
5. Switch ON the Service Switch on the SUB board near the TGP board.
6. Install the dial gauge onto HSDCD Slip Ring PCB surface, using the attachment tool (see illustration 2-17).
7. Rotate the Gantry by hand and find the average of radial eccentric position of the slip ring:
a. Find the Innermost and Outermost point;
b. Calculate the average between both;
c. Rotate the Gantry so that the obtained average value stay positioned underneath the HSDCD
Receiver Assy position.
d. Switch OFF the Service Switch.
HSDCD Receiver
HSDCD Antenna
HSDCD Support 4
2-9 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Screw and
washer (x3)
screw in the middle of hole
HSDCD HSDCD
Antenna Support 1
PCB
Slip Ring
9. Insert the thickness gauge provided in the Alignment Tool between the HSDCD Antenna and Slip Ring.
Screws (x2)
HSDCD
Receiver
2-10 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Screws (x2)
11. Tighten the two screws A of HSDCD Support 2. These screws keep the HSDCD Antenna in parallel with Slip
Ring’s PCB. (Illustration 2-12).
A (both side)
HSDCD Support 1 HSDCD
B Support 2
C
(both side)
2-11 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
OK OK Not allowed
Readjustment
required
2-12 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
MEASUREMENT CHECK
Special Equipment
Prepare the following measurement tools:
• Shim (Alignment Tool)
• Master Gauge (Alignment Tool)
• Magnifying glass
a. Prepare a 4.3mm shim and insert/remove few times in the 4.5mm Master Gauge. The objective of this
procedure is to obtain a better accuracy by familiarizing yourself the clearance of a determined thickness.
Master Gauge
Master Gauge
4.3mm shim
2-13 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
PCB
HSDCD
Antenna
2-14 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
RF Cables
HSDCD
Antenna
19. Switch ON the Service Switch on the SUB board near the TGP board.
20. Rotate the Gantry manually to perform the following checks:
Check to make sure that the HSDCD Antenna does not touch the Slip Ring during its revolution.
Check to make sure that the cables does not catch on any stationary components during each revolution.
Check if the movement is smooth and there is no abnormal noise. Make more than one complete rotation.
21. Perform the Gantry rotation using TGP service switches and verify if the movement is smooth.
22. Restore the HSDCD Receiver cover original configuration.
23. Perform following adjustment and check according to the CD-ROM manual, Functional Check & Adjustment,
DAS/DETECTOR.
DATA TRANSFER CHECK
24. Install the rear, right side, and left maintenance covers.
25. Switch ON the ‘Rotate‘, ‘XG Power‘, ‘Slip Ring115V‘ and ‘Table Tilt‘ switches at the Gantry rear base.
26. Restore the Gantry to original configuration.
27. END
2-15 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• Gloves
• Vacuum Cleaner
• Attachment Tool
• Plastic Hammer
CAUTION
When servicing the Slip Rings and Brushes, wait approximately five minutes after switching
OFF the CB1 in the PDU for all capacitors in the XG Unit to discharge.
CAUTION
Exercise caution when working with slip ring components to avoid contact, inhalation, and
ingestion of slip ring brush powder.
Do not remove gloves near an exposed slip ring. The powder inside the glove can
contaminate the ring.
NOTICE
Do not touch the slip ring surfaces. Do not touch the brush surfaces either.
Do not handle the slip ring surfaces and brushes without GLOVES.
2-16 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Attachment Tool
For RF Dial Gauge
Slip Ring
For HSDCD
Slip Ring Dial Gauge
PCB surface
2-17 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
(*2)
Slip Ring (*2)
Support Frame
Tighten 6 Mounting
Pin (*1) Bolts (Torque:
0.98Nm/10kg.cm)
Mounting Bolts
Bolts
2-18 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Hammer the inner circumference part of the slip ring assy only. Do not hit other parts.
If the slip ring assy does not move, perform the following until the slip ring can be moved by hammering:
i. Loosen the 6 mounting bolts tightened in step e, and tighten them again. (Torque: decrease by
1kg.cm).
h. Repeat steps f and g, until the slip ring assy is positioned at the Gantry rotation center.
for HSDCD Slip Ring: less than 0.7mm, ignore the PCB TERMINATION GAP.
Note
If the position of the slip ring assy does not meet the specification, loosen the 2(x3) bolts fastening
support frame (without Pin) to Gantry rotational frame, and perform step h, then tighten the 6 (2x3)
bolts (Torque: 6N.m) (see illustration 2-18).
Rod
a
a’
Inner Circumference
2-19 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
6. Tighten the rest mounting bolts (Torque: 6N.m) in the cross order shown in illustration 2-20 ( 1 ∼ 6 ).
7. Install the following components:
9. END
Pin
1 (behind Support Frame)
Pin
(behind Support Frame)
1 4
6 3
6 2
4 5
3 5
2 Pin
(behind Support Frame)
2-20 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
CAUTION
Gantry may experience sudden high speed rotation due to order from the OC. Be very
careful; stand clear of the rotating Gantry.
3-2 GANTRY
HiSpeed Dual, ProSpeed FII
5116376
GANTRY
FUNCTIONAL CHECK / ADJUSTMENT
Management
Table Processor Processor
DISP B'd Disp
SW B'd B'd LG B'd
Position Tilt
Disp4 Disp1 Disp0 Disp2 Disp3 DS DS DS DS DP DS Disp5 Disp7 DS DS Disp6 DS DS DS
Inter Pos Hit PS PI 1 2 3 4 5 TS TI 6 7 DP 8 EXLM FWD BWD Xon 1 2 F S
Lock
0
1
2
3
3-3
4
GANTRY INITIALIZE MOVEMENT (CONTINUED)
5
6
7
8 ( )
Illustration 3-1
9
GE HEALTHCARE
10
REV 1
11
3-1
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
c. Check if the rotation time shown in the Position Display shows a value 1000 ±5.
If not, return to step 4-b.
5. If CHANGE LED on the TGP Board lit on, press the FAST and the RANGE keys simultaneously on the gantry
switch panel to store the new adjustment data.
3-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
7. Set the TGP service switches as follows, when completed all of above check/adjustment procedure.
ABT/SVE/FIX : SVE
CONT/HOME/90° : HOME
SYS/OFF/MNL : SYS
8. Set the G6 Gantry dip switch (switch S2 : location 7S) to OFF on the TGP Board.
9. Press the RESET switch on the TGP Board.
10. Restore the Gantry to original configuration.
3-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
3-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
CAUTION
When servicing the Slip Rings and Brushes, wait approximately five minutes after switching
OFF the CB1 in the PDU for all capacitors in the XG Unit to discharge.
CAUTION
Exercise caution when working with slip ring components to avoid contact, inhalation, and
ingestion of slip ring brush powder.
Gloves : Large size : 46-194427P400, X-Large size : 46-194427P401
HEPA Vacuum Cleaner : 46-297933P1 to remove brush block powder (dust).
Do not remove gloves near an exposed slip ring. The powder inside the glove can
contaminate the ring.
NOTICE
Do not touch the slip ring surfaces. Do not touch the brush surfaces either.
Do not handle the slip ring surfaces and brushes without GLOVES.
Power
Slip
Rings Power
Cables
Brush
Block
Assy
Power
Brushes
CN1
Signal
Brushes
4-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• Ring Service Tool (2206131)
This includes a test battery source. The output voltage should be 6 V or more; otherwise replace the dry
batteries with new ones.
• Oscilloscope
• Maintenance Connector
Overview
The following procedure checks if the contact (conductivity) between signal brushes and slip rings is proper. The
conductivity is examined by injecting a DC current and observing the current flow in the circuit by the oscilloscope
while rotating the slip ring, as outlined in Illustration 4-1.
Ten signal slip rings are equipped on the slip ring frame:
7 & 8: for DAS Trigger signal
9 & 10: for TGP → OGP Com. Data
11 & 12: for OGP → TGP Com. Data
The contact check will be performed for each of these three sets of rings.
Signal Board
7 & 8, or
9 & 10, or
11 & 12
6 VDC 120ohm
120 W
Oscilloscope
Short Circuit in
Slip Ring Frame
4-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Slip Ring
4-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Illustration 4-3 Signal Brush Board Wire Connection - HSDCD Brush Block
Oscilloscope
11 9 7
Resistor
12 10 8 120W
120ohm
4-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Check to make sure the removed cables does not catch on the any stationary components
during each revolution.
4. Switch ON the ‘Rotate’ switch at the rear of the Gantry.
5. Rotate the Gantry and observe the current flow (voltage across a register) on oscilloscope:
a. Set the TGP Service Switches as follows to rotate the Gantry (0.7 sec/Rot).
SYS/OFF/MNL : MNL
SPD2/SPD1/SPD0 : SPD2
FAST/MID/SLOW : FAST
CONT/HOME/90° : CONT
ABT/SVE/FIX : FIX
b. Verify that there are no voltage drops grater than 0.5 V or voltage fluctuations.
c. Set the CONT/HOME/90° Service Switch to ‘HOME‘.
6. Repeat the above check for the other slip rings and brushes (for Rings 9 & 10 and 11 & 12) (see illustration 4-3).
7. Switch OFF the ‘Rotate‘ switch.
8. Restore the Signal Brush Board and Slip Ring to original configuration.
a. Remove the oscilloscope probes and power supply wires.
b. Connect the cable connector CN1 to the Signal Brush Board.
c. Disconnect the maintenance connector from the Signal Interface Board, and connect the signal cable to it.
9. Set the TGP Service Switches to original configuration.
10. Restore the Gantry and the PDU to original configuration.
4-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Do not touch the slip ring surfaces. Do not touch the brush surfaces either.
For HSDCD Brush Block, follow according to the CD-ROM manual below:
COMPONENT REPLACEMENT - GANTRY Section - HSDCD BRUSH Assy, Removal subsection.
4-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Low-Power
Brushes (GND)
Low-Power Brushes
(115V)
High-Power
Brushes (480V)
Signal Brushes
Check
mark
4. Restore the Brush Block to its original configuration. Refer to CD-ROM manual below:
4-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• HEPA Vacuum Cleaner
• Kim Wipe (2254011)
Understand and follow the Safety Guidelines Manual.
1. Preparation:
a. Remove the PDU front cover by unscrewing its 2 screws.
b. Switch OFF the CB1 and CB5 breakers in the PDU.
c. Switch OFF the ‘Rotate‘ switch at the Gantry rear base.
d. Remove the rear Gantry cover.
2. Disconnect the cable connector CN1 connected to the signal brush board.
3. Remove the protect cover by unscrewing its 4 screws from the HSDCD brush block assy.
4. Remove the Brush Block following the CD-ROM manual below:
Power
GANTRY REAR VIEW Cables Power Slip
Rings
Brush Block
Assy
Power
Brushes
CN1
Signal
Brushes
4-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Handle the Brushes with care to avoid breakages or deep scratches.
Signal Brushes
High-Power Brushes
(480V)
Low-Power
Brushes (115V)
Low-Power
Brushes (GND)
6. Wipe the scrapings from the brush surface with the dry Kim Wipe.
7. Restore the Brush Block to its original configuration. Refer to CD-ROM manual below:
4-9 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
4-4-1 Method 1
Special Equipment
• Kim Wipe (2254011)
During periodic maintenance, or when changing the brushes, the Gantry slip rings should be checked for loud
scrapping noises.
NOTICE
Keep grease or dust away from the brushes as grease or dust will considerably deteriorate
the life and performance of the brushes.
Understand and follow the Safety Guidelines Manual.
1. Preparation:
a. Remove the PDU front cover by unscrewing its 2 screws.
b. Switch OFF the CB1 and CB5 breakers in the PDU.
c. Switch OFF the ‘Rotate‘ switch at the Gantry rear base.
d. Remove the Gantry rear and left maintenance covers.
2. Remove the Brush Block following the CD-ROM manual below:
4-10 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
NOTICE
Do not file the slip rings using abrasive or equivalent.
3. Clean the power slip rings and the surrounding area:
a. Switch ON the ‘Rotate‘ switch at the Gantry rear base.
b. Rotate the Gantry (15 sec/Rot) by setting the TGP service switches as follows;
SYS/OFF/MNL : MNL
SPD2/SPD1/SPD0 : SPD0
FAST/MID/SLOW : SLOW
CONT/HOME/90° : CONT
ABT/SVE/FIX : FIX
During the rotation, use a vacuum cleaner to clean the filings/powder on the rings and ring housing.
Clean with a Vacuum Cleaner only.
c. Stop the Gantry rotation by set the CONT/HOME/90° Service Switch to HOME.
d. Switch OFF the ‘Rotate‘ switch.
e. Use dry Kim Wipe to clean the ring housing, and the surfaces of the base frame located below the slip ring
housing.
4. Install the Brush Block following the CD-ROM manual below:
4-11 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Special Equipment
• SlipRing Eraser (5169251)
Understand and follow the Safety Guidelines Manual.
1. Gantry Preparation:
a. Remove the PDU front cover by unscrewing its 2 screws.
b. Switch OFF the CB1 and CB5 breakers in the PDU.
c. Switch OFF the ‘Rotate‘ switch at the Gantry rear base.
d. Remove the Gantry rear maintenance cover.
2. Remove slip ring covers.
3. Disconnect all connections to the Brush Block Assy.
4. Carefully remove the Brush Block Assy.
Note
Use of Neoprene or nitrile gloves to limit irritation and ingestion of metallic dusts is recommended.
Do not remove gloves near an exposed slip ring. The powder inside the glove can contaminate the
ring.
5. Clean off the dust from the slip ring tracks and carefully around the block with a HEPA vacuum cleaner and the
soft brush attachment.
Note
The soft brush attachment that comes with the HEPA vacuum cleaner should NOT be used for any-
thing other than slip ring brush debris cleaning. The brush must be kept clean to avoid aontamina-
tion of the slip ring and brush tips. It is recommended to store the brushes or brush block in a sep-
arate closed bag (such as a plastic Zip-lock bag).
6. With the slip ring eraser (Illustration 4-7), carefully rub the tracks using a large, sweeping motion.
4-12 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
IMPORTANT NOTE: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Do not rub intensely in one spot for a long period of time. The ring color should return to a
shiny new brass color. (Illustration 4-8)
----------------------------------------------------------------------------
7. Clean the track again with the HEPA vacuum cleaner and the soft brush attachment.
8. Wipe the track with a soft white linen cloth while using the vacuum cleaner to remove any other debris.
9. Remove gloves and wash hands thoroughly after cleaning.
4-13 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
4-14 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
• Detector Surface
• Inside of the Myler Ring
5. Restore the Gantry and the PDU to the original configuration.
4-15 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 15 5116376
Inside of the Gantry Covers Gantry Rear Base and Slip Ring Inside of the Slip Ring Covers
4-16 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
5-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
7. Tilt the Gantry to 0 deg. position until touching the 0° Adjuster Tool as shown in the Illustration 5-1.
05 Adjuster Tool
(both sides)
5-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
TABLE
NO CLEARANCE
NO CLEARANCE
5-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
5-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
Operation Time
From BWD 20 deg. to FWD 20 deg. 37 ±3 sec. (34 ∼ 40 sec.)
From FWD 20 deg. to BWD 20 deg. 37 ±3 sec. (34 ∼ 40 sec.)
Note
Actually, the tilt operation stops at 0 deg. when you tilt the Gantry from BWD 20 deg. to FWD 20
deg., or from FWD 20 deg. to BWD 20 deg. For this reason, measure the time in the following way:
Time from BWD 20 deg. to FWD 20 deg. Time from BWD 20 deg. to 0 deg.
+
Time from 0 deg. to FWD 20 deg.
Time from FWD 20 deg. to BWD 20 deg. Time from FWD 20 deg. to 0 deg.
+
Time from 0 deg. to BWD 20 .deg.
If the time is out of the specified range, perform the ‘Tilt Speed Adjustment‘.
5-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
Removing the Table Front Bottom Cover to access the Hydraulic Valve Adjuster
a. Move the cradle OUT to its fully retracted position (farthest from Gantry).
b. Raise the Table to its highest position.
c. Switch OFF the ‘Table/Tilt‘ switch at the Gantry rear base.
d. Remove the two screw caps from the rear bottom cover.
e. Unscrew the two screws and remove the rear bottom cover.
f. Remove the four screw covers from foot pedals.
Note
If the Foot Pedal Option is not installed, skip the step g.
g. Unscrew the four Allen screws and remove the four foot pedals.
h. Remove the four screw caps from the front bottom cover.
i. Unscrew the four screws and remove the front bottom cover.
Screw Cover
Foot Pedal
Screw
Rear Bottom Cover Caps
Front Bottom Cover
5-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
GANTRY FRONT
F : FAST
F S : SLOW
FWD
S
F
BWD
5-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
NOTICE
This is thermal-sensitive adjustment: When the tilt operation is repeated many times, oil in
the tilt line becomes hot so that the tilt speed is faster. Therefore, perform this adjustment
speedily.
7. Adjust the FWD adjuster:
a. Measure the time of movement from BWD 20 deg. to FWD 20 deg.
b. If the time is 37 ± 3 sec, go to step 8; otherwise, perform the following:
If the time is less than 34 sec, rotate the FWD adjuster for 1.0 scale interval in the CCW (S) direction.
If the time is more than 40 sec, rotate the FWD adjuster for 1.0 scale interval in the CW (F) direction.
5-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
Arm
Tilt Mark
Side
Plate
Tilt Mark
Arm
Side
Plate Tilt Mark 05
Arm
Side Plate
Arm
Tilt Mark
(FWD20)
Arm
Tilt Mark
Arm
Side
Plate
Tilt Mark
(BWD20)
5-9 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
5-10 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
TEST1
ON
TEST2
OFF
T1 T8 S1
TGP BOARD
2. Push TEST1 switch on the TGP board, until the height display of the Gantry display panel indicates ‘000‘. (refer
to illustration 5-8)
3. Press the FWD button until the Gantry tilt forward to FWD 20 degree position (by tilt mark FWD 20 on the tilt
arm).
NOTICE
If the Gantry can not be tilted to the specified angle due to the interlock function, switch ON
(up) the T3 Table dip switch on the TGP board to disable the interlock function, and continue
to tilt the Gantry. In this case, be careful not to have the Gantry collide against anything.
4. Set the position display to ‘5‘ using INLM (Internal Landmark) and EXLM (External Landmark) keys on the
Gantry Switch Panel.
5. Push TEST2 switch on the TGP board.
a. If CHANGE LED is lit, press FAST and RANGE keys (Gantry Switch Panel) together.
b. Verify that CHANGE LED is OFF.
6. Push TEST1 switch on the TGP board, until the height display of the Gantry display panel indicates ‘001‘.
7. Press the BWD button until the Gantry tilt backward to BWD 20 degree position (by tilt mark BWD20 on the tilt
arm).
8. Set the position display to ‘405‘ using INLM and EXLM keys on the Gantry Switch Panel.
9. Push TEST2 switch on the TGP board.
a. If CHANGE LED is lit, press FAST and RANGE keys (Gantry Switch Panel) together.
b. Verify that CHANGE LED is OFF.
5-11 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 16 5116376
WARNING
DO NOT FORGET TO SWITCH OFF THE T3 TABLE DIP SWITCH (IF IT IS SET TO ON),
OTHERWISE THERE WILL BE COLLISION HAZARD, SINCE THE INTERLOCK FUNCTION
DOES NOT WORK, IF T3 IS SET TO ON.
11. Perform the Tilt Angle Check (refer to 5-4-1 Tilt Angle Check ).
5-12 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
SECTION 6 - COLLIMATOR
6-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Raw Data File Raw Data File No. to be Mean File (Vector) No. File Comment
Selected
(7 mm Thickness Scan) Exam#1, Series#1, 1 7mm Ach
Acq No: 1
(1 mm Thickness Scan) Exam#2, Series#1, 2 1mm Ach
Acq No: 1
(2 mm Thickness Scan) Exam#3, Series#1, 3 2mm Ach
Acq No: 1
(3 mm Thickness Scan) Exam#4, Series#1, 4 3mm Ach
Acq No: 1
(5 mm Thickness Scan) Exam#5, Series#1, 5 5mm Ach
Acq No: 1
(10 mm Thickness Scan) Exam#6, Series#1, 6 10mm Ach
Acq No: 1
Note: “Ach“ described in File Comment means A channel. “Bch“ should be commented when testing B chan-
nel
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A Side. ( A channel )
c. Select the raw data file ( Exam#1, Series#1, Acq No: 1 ) from the Raw data browser lists.
d. Perform Fan Data with the following settings, then click on OK:
6-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
6-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
0.16
0.15
0.14
0.13
0.12
0.11
6-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
General Information
Prerequisites for this test are as follows:
• The DAS/Detector has been powered ON for more than two hours.
• The x-ray alignment (‘Plane of Rotation’, ‘Detector Bean-on-Window’, ‘Q-cal Channel Ratio’, ‘Iso Center
Alignment’, and ‘Filter Center Alignment’) is proper.
After ending this test, the ‘Filter Center Alignment’ check/adjustment is required.
Replace the filter if the test below fails; or, replace the filter approximately every 100,000 scans, since the filter
material will be gradually deteriorated by x-ray radiation, which may cause crack or break in the filter.
1. Preparation:
a. Switch OFF the ‘Rotate’ switch at the Gantry rear base.
b. Remove the gantry front and both side covers.
c. Switch ON the ‘Rotate’ switch.
2. Perform two air stationary scans with the filter installed and removed:
a. Select Offline Scan; refer to below:
6-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Raw Data File Raw Data File No. to be Mean Vector File Comment
Selected No.
(Filter Scan) Exam#1, Series#1, 1 Filter Ach
Acq No: 1
(No Filter Scan) Exam#2, Series#1, 2 No Filter Ach
Acq No: 1
Note: “Ach“ described in File Comment means A channel. “Bch“ should be commented when
testing B channel
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A side. (A channel)
c. Select the raw data file (Exam#1, Series#1, Acq No: 1) from the Raw data browser lists.
d. Perform Fan Data with the following settings, then click on OK:
6-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
6-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
40.000
10.000
6-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
6-9 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Z–Axis Motor
Pulley Lower Belt
6-10 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
GANTRY
Scan Center
TABLE
Right-Left
Table Center Line Direction
7-1 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
WARNING
ROTATION HAZARD! WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON
AND SMALL BUTTON), THE GANTRY QUICKLY ROTATES TO THE 0 DEG. POSITION. IF IT
IS NECESSARY TO PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY,
SWITCH OFF THE ‘ROTATE’ SWITCH FIRST.
2. Perform an axial scan of the head holder:
a. Mount the axial head holder to the end of the cradle.
b. Switch ON the positioning lights.
c. Advance the cradle into the Gantry until the internal light cuts the approximately middle section of the head
holder.
d. Perform an axial scan of the head holder using the following technique:
e. Scan Parameters: 35 cm FOV, 3 sec, 120 kV, 60 mA, 10 mm Thickness
3. Check whether the Table center line and the scan center are aligned:
Verify that the difference in the distances ( |1-2| ) is within ± 2 mm. If not, proceed to next step.
1 2
7-2 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Gantry Base
Mounting Nut
Table Base M8 (x2)
7-3 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
RIGHT-LEFT
DIRECTION
INNER INNER
HORIZONTAL LEFT RIGHT
DIRECTION GANTRY
OUTER OUTER
LEFT RIGHT
GANTRY
OUTER
TOP
OUTER
TOP
TABLE VERTICAL TABLE
DIRECTION
(TOP VIEW)
(SIDE VIEW)
The positions of the Inner right and left lights, and Outer right and left lights are adjusted in the horizontal and
vertical directions.
The position of the Outer top light is adjusted in the right-left and horizontal directions.
7-4 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
WARNING
ROTATION HAZARD! WHEN YOU PRESS THE ’POSN LIGHT’ BUTTONS (LARGE BUTTON
AND SMALL BUTTON), THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT
IS NECESSARY TO PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY,
SWITCH OFF THE ‘ROTATE’ SWITCH FIRST.
1. Preparation.
a. Switch OFF the ’Rotate’ switch at the Gantry rear base.
b. Remove the Gantry front and both side cover.
c. Switch ON the ’Rotate’ switch.
2. Place a fine pin (ex. M3 size hexagonal wrench) on the center of the phantom holder. See Illustration 7-4.
Head Holder
7-5 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Phantom Holder
7-6 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Scan Center
Wrench
7-7 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Adjusting Tube
Adjust Adjust A
Direction Screw/Lever
1 – 1’ A Steel Plate
2– 2’ B a
3 – 3’ D
Before adjusting A, B, or D, loosen a,
b, or d respectively; after adjustment, b
tighten a, b, or d accordingly.
2
1
B
2’
1’ 3’
1 D
3’
d
Light Screen (A hex screw is installed inside this hole)
3
2
1’
2’
7-8 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Phantom
Horizontal Line
Phantom Surface
7-9 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
e. Move the vertical line until it just touches the surface of the phantom scout image. See Illustration 7-9.
f. Press the [Enter] key.
g. Press the [End] key.
h. Select ’Confirm’ on the Touch Panel screen and press the ’Table set’ button.
The phantom surface moves to the scan plane position.
Phantom Surface
Vertical Line
7-10 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
7-11 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Move the cradle to the furthest (Out) position from the Gantry.
2. Push the ’Down’ button until the Table reaches its lowest position.
3. Hold down the ’Up’ button.
Verify that the ’cradle longitudinal position display’ changes to ’Table height display’, and that the Table stops
on the way up with the ’Table height display’ blinking.
Free the ’UP’ button and hold it down again until the highest position is reached.
4. Return the Table to its lowest position using the ’Down’ button.
5. Do the same check (step 3) with the Foot Switches.
6. Push the ’Height’ button and verify that the ’longitudinal display’ changes to ’height display’.
7-12 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Verify that the Gantry rotates to the Home position and the 5 positioning lights are turned ON.
(The Gantry does not rotate, if it is already positioned at the Home position)
Verify that the positioning lights are turned OFF automatically after approximately 1 minute.
(If the positioning lights are not turned ON, push the reset switch on the TGP Board once and perform the
above)
7-3-6 Home
1. Raise the Table to approximately -50 mm height.
Move the cradle to the 200 mm position in the In direction from the outer limit position.
7-13 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
Move the cradle to any position except the out limit position.
2. Move the Table down until it stops automatically; this is the interlock position.
Verify that the Table up/down function and Gantry tilt function are interlocked along the dashed line indicated
in Illustration 7-10, but that the cradle in/out function can still operate.
3. Move the cradle to the out limit position.
FWD 25.0
20.0 INTERLOCK AREA
15.0
TILT ANGLE [deg.]
10.0
5.0
0.0
UP/DOWN, TILT AREA
5.0
10.0
15.0
20.0
BWD 25.0
–250 – 200 –150 –100 –50 0
TABLE HEIGHT [mm]
7-14 GANTRY
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
TABLE
TABLE OF CONTENTS
SECTION PAGE
i TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
ii TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
NOTICE
Go to Section 3 Short-Foot-Print Function in this Tab, when it is using Short-Foot-Print Mode
at the Site.
10. END
Screw Cover
Foot Pedal
Screw Caps
Rear Bottom Cover Front Bottom Cover
1-1 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
11. END
1-2 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
Verify that the Table and Gantry motions are smooth and quiet.
4. Verify that the Table height ‘H’ is less than 301mm . (See Illustration 1-2 for proper measuring points)
5. Press and hold the ‘UP’ button on Gantry Panel Switch.
The Table stops at a height of approximately 675mm.
Release the ‘UP’ button and depress it again until the Table stops at its highest position.
(Mechanical Highest Limit Position)
6. Verify that the Table height ‘H’ is more than 887mm. (See Illustration 1-2 for proper measuring points)
7. Set the T3 switch of the TGP S1 switch to OFF position (Refer to Switch/Jumper 2-2).
(Enable the Table-Gantry interlock function)
8. Restore the Table to original configuration.
NOTICE
Do not forget to switch OFF the T3 switch, otherwise there will be collision hazard, since the
interlock function does not work.
Note
Verify that the Table up and down operations can be correctly performed by Gantry Panel Switch
(or by each foot pedal option), when the above check procedure is finished and the front and rear
bottom covers are re-installed.
1-3 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
1-4-1 Check
1. Remove the front cover and left maintenance cover from the Gantry. (Refer to the “Component/Replacement”
manual)
2. Remove the Table front and rear bottom covers. (Refer to Section 1-1)
3. Move the Cradle to the out limit position. (farthest from Gantry).
4. Set the T6 switch of the TGP S1 switch to ON position (Refer to Switch/Jumper 2-2).
5. Push TEST1 switch on the TGP board until the height display on the Gantry Display indicates ‘011’.
6. Lower the Table to the down limit position.
7. Measure the Table height ‘H’. (e.g. It may be 301 mm or so.)
8. Read the value of position display, while pushing RANGE key on the Gantry Switch Panel.
9. Verify that the position display reads
{(H - 301) X 2} ± 10. (e.g. It may be “30±10” or so.)
If not, perform Table Height adjustment.
10. Raise the Table to the up limit position.
11. Measure the Table height ‘H’. It may be 887 mm or so.
12. Read the value of position display, while pushing RANGE key on the Gantry Switch Panel.
13. Verify that the position display reads {(H - 301) X 2} ± 10. (e.g. It may be “1172±10“ or so.)
If not, perform Table Height Adjustment.
14. Set the T6 switch of the TGP S1 switch to OFF position (Refer to Switch/Jumper 2-2).
15. Restore the Table to original configuration.
1-4 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
(FRONT VIEW)
(84.3mm) H 74.8 mm
9.5mm
FLOOR
1-5 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
1-4-2 Adjustment
1. Move the Cradle to the out limit position.
2. Set the T3 (interlock release) switch of the TGP S1 switch to ON position. (Refer to Switch/Jumper 2-2)
3. Lower the Table to the mechanical down limit position.
In the mechanical down limit, the Table height ‘H’ may be 301mm.
4. Set the T6 switch of the TGP S1 switch to ON position. (Refer to Switch/Jumper 2-2)
5. Push TEST1 switch on the TGP board, until the height display on the Gantry Display indicates ‘009’.
6. Check the value of position display indicates “1”.
If not, adjust the position display to “1” by pressing the ‘INLM (Internal Landmark)’ or ‘EXLM (External
Landmark)’ keys.
7. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press FAST and RANGE keys together on the Gantry Switch Panel.
Check that CHANGE LED is OFF.
8. Set the T6 switch of the TGP S1 switch to OFF position. (Refer to Switch/Jumper 2-2)
9. Raise the Table to the mechanical up limit position.
In the mechanical up limit, the Table height ‘H’ may be:
LC Table: approximately 887mm.
10. Set the T6 switch of the TGP S1 switch to ON position. (Refer to Switch/Jumper 2-2)
11. Push TEST1 switch on the TGP board, until the height display on the Gantry Display indicates ‘010’.
12. Check the value of position display indicates ”1177”.
If not, adjust the position display to ”1177” by pressing the ‘INLM’ or ‘EXLM’ keys.
13. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press FAST and RANGE keys together on the Gantry Switch Panel.
Check that CHANGE LED is OFF.
14. Set the T3 and T6 switch of the TGP S1 switch to OFF position (Refer to Switch/Jumper 2-2).
15. Restore the Table to original configuration.
1-6 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 14 5116376
4. Set the T6 switch of the TGP S1 switch to ON position. (Refer to Switch/Jumper 2-2)
5. Push TEST1 switch on the TGP board until the height display on the Gantry Display indicates ‘013’.
6. Adjust the position display XXXX to {1000 + 2X} by pressing the ‘INLM’ or ‘EXLM’ keys.
e.g.: When the cradle is positioned at 10mm above the scan center, adjust display to 1020 (1000 + 2x10).
When the cradle is positioned at 10mm under the scan center, adjust display to 980 (1000 + 2x (-10)).
7. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press FAST and RANGE keys together on the Gantry Switch Panel.
Check that CHANGE LED is OFF.
8. Set the T6 switch of the TGP S1 switch to OFF position. (Refer to Switch/Jumper 2-2)
1-7 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
blank
1-8 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Verify that the cradle stops moving, and that the Gantry Display goes blank; this indicating that the cradle
is unlatched.
b. Push the Unlatch switch again (‘Latch’).
c. Release the ‘IN’ button, and then push it.
Verify that the cradle starts moving and the Gantry Display changes to normal (displaying a position in
millimeter).
3. Repeat the above same check for the Unlatch switch on the opposite side.
2-1 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
FRAME
DF DR
CRADLE
GANTRY
FRAME
A
BEARING
2-2 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Bearing
Roller Bearing
SIDE VIEW AR
0.5mm + 0.1mm
Cradle Bearing
Shim
Roller
Cradle Support
AR(AL) Screw
2-3 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Out to In Travel
3. Move the cradle to the Mechanical Out limit position by hand.
4. Press the ’INLM’ button, and verify that the Gantry Display indicates Zero.
5. Mark the Table cover with a marking tape or other at one end of the cradle. Define this position as a reference.
6. Move the cradle to 1000 mm (Display) by pushing the ‘In’ button (use the slow speed).
7. Measure the actual distance of cradle movement.
In to Out Travel
8. Move the cradle to the Mechanical In limit position by hand.
9. Press the ’INLM’ button, and verify that the Gantry Display indicates Zero.
10. Mark the Table cover with a marking tape or other at one end of the cradle. Define this position as a reference.
11. Move the cradle to 1000 mm (Display) by pushing the ’Out’ button (use the slow speed).
12. Measure the actual distance of cradle movement.
2-4 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Out to In Travel
3. Move the cradle to itís Mechanical Out limit position by hand.
4. Move the cradle approximately 100 mm, by pushing ’In’ button.
5. Press the ’INLM’ button, and verify that the Gantry Display indicates Zero.
6. Mark the Table cover with a marking tape or other at one end of the cradle. Define this position as a reference.
7. Move the cradle to 1000 mm (Display) by pushing the ’In’ button (use the slow speed).
8. Move the cradle to 0 mm (Display) by pushing the ’Out’ button (use the slow speed).
9. Measure the cradle position difference between before and after the travels.
In to Out Travel
10. Move the cradle to its Mechanical In limit position by hand.
11. Move the cradle approximately 100 mm, by pushing ’Out’ button.
12. Press the ’INLM’ button, and verify that the Gantry Display indicates Zero.
13. Mark the Table cover with a marking tape or other at one end of the cradle. Define this position as a reference.
14. Move the cradle to 1000 mm (Display) by pushing the ’Out’ button (use the slow speed).
15. Move the cradle to 0 mm (Display) by pushing the ’In’ button (use the slow speed).
16. Measure the cradle position difference between before and after the travels.
2-5 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Check
1. Press ’OUT’ key and ’FAST’ key on the Gantry switch panel to move the cradle to out limit position.
2. Press ’OUT’ key again for few seconds, then press ’INLM’ key.
3. Move the Cradle by hand to mechanical out limit position.
4. Check that the position display indicates “5.0 ± 2.5”.
5. If not, perform the adjustment procedure, on the next page.
6. Move the cradle to in limit position by pressing ’IN’ and ’FAST’ keys.
7. Press ’IN’ key again for few seconds.
8. Check that the position display indicates “1525 ± 5.0”.
9. If not, perform adjustment.
2-6 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Adjustment
If the Cradle position is out of specification, proceed as shown below.
Note
Table height adjustment must be done before this adjustment.
1. Set the Gantry to the 0 degree tilt position.
2. Set the table to ’200’ mm height position (shown on Gantry display).
3. Move the cradle to the mechanical out limit position by hand. (farthest from gantry).
4. Set the T6 switch of the TGP S1 switch to ON (Refer to Switch/Jumper 2-2).
5. Push TEST1 switch on the TGP board, until the height display on the Gantry Display indicates ’003’.
6. Verify that the position display indicates ’0’, then push TEST2 switch on the TGP board.
If the CHANGE LED is ON, press the ‘RANGE’ and ‘FAST’ keys together on the Gantry Switch panel.
Verify that the CHANGE LED is OFF.
Note
For TGP2 board, if the CHANGE LED can NOT become ON after pushing TEST2 switch, it
indicates the Cradle Potentiometer is at fault, please replace the Cradle Potentiometer.
7. Verify that the cradle is still at mechanical out limit position.
8. Push TEST1 switch on the TGP board, until the height display on the Gantry Display reads ’004’.
9. Verify that the position display indicates ‘0’.
Then move the cradle IN by pushing IN button until the position display indicates ’3040 ± 10’.
If cradle stopped due to interlock and the position display indicated smaller than ’3030’, move the cradle IN until
the position display indicates ’3040 ± 10’ by hand.
10. Push TEST2 switch on the TGP board.
If the CHANGE LED is ON, press ‘FAST’ and ‘RANGE’ keys together on the Gantry Switch panel.
Verify that the CHANGE LED is OFF.
Note
For TGP2 board, if the CHANGE LED can NOT become ON after pushing TEST2 switch, it
indicates the Cradle Potentiometer is at fault, please replace the Cradle Potentiometer.
11. Set the T6 switch of the TGP S1 switch to OFF position (Refer to Switch/Jumper 2-2).
2-7 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Check
1. Raise the Table to 100mm height (shown on Gantry display).
2. Move the cradle IN approx. 400mm from the out limit.
3. Push the positioning light switch and mark the position on the cradle where is lit up with positioning light beam.
4. Raise the table to 0mm height by pushing UP button. (shown on Gantry display)
5. Push the positioning light switch again, and check if the distance between the mark and the positioning light
beam is less than 1 mm.
2-8 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Adjustment
If the cradle compensation is out of specification, proceed as shown below.
1. Raise/lower the Table to 50mm height (shown on Gantry display).
2. Move the cradle IN approx. 400mm from the out limit.
3. Push the positioning light switch and mark the position on the cradle where is lit up with positioning light beam.
4. Set the T6 switch of the TGP S1 switch to ON (Refer to Switch/Jumper 2-2).
5. Push TEST1 switch on the TGP board until the height display on the Gantry Display indicates ’012’ .
6. Push TEST2 switch on the TGP board.
7. Lower the Table approx. 150mm (using a measure).
8. Push the positioning light switch again, and move the cradle until the mark made in step 3 is lit up with
positioning light beam.
9. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press ‘FAST’ and ‘RANGE’ keys together on the Gantry Switch panel.
Verify that CHANGE LED is OFF.
10. Set the T6 switch of the TGP S1 switch to OFF position (Refer to Switch/Jumper 2-2).
2-9 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
Fishing Scale
2-10 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 18 5116376
14. END
2-11 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
blank
2-12 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-1 CAUTION
Note
This function is available for the Gantry with TGP board 2156510-5 or later.
The short-foot-print function can limit table-DOWN movement or cradle-IN movement so that the system can be
installed in a small scan room.
WARNING
PATIENT INJURY!
WHEN SHORT-FOOT-PRINT FUNCTION IS USED, AT THE MINIMUM THE FOLLOWING
ROOM MUST BE DEDICATED TO PREVENT THE PATIENT FROM PINCHING BETWEEN
TABLE (OR CRADLE) AND WALL.
NOTICE
When table height is limited between 450 mm and 900mm as its DOWN limit, the Gantry front
cover must be removed by two persons and with a special protector (2225358) or a blanket.
3-1 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-2-1 Adjustment
15. Move the Cradle to the out electrical limit position.
16. Lower the Table to the lowest position desired.
WARNING
PATIENT INJURY!
WHEN SHORT-FOOT-PRINT FUNCTION IS USED, AT THE MINIMUM CLEARANCE OF 120
MM MUST BE DEDICATED TO PREVENT THE PATIENT FROM PINCHING BETWEEN TABLE
(OR CRADLE) AND WALL. SEE ILLUSTRATION 3-1.
17. Set the T6 switch of the TGP S1 switch to ON position (Refer to Switch/Jumper 2-2).
18. Push TEST1 switch on the TGP board until the height display on the Gantry Display indicates ‘035’.
19. Set the T2 switch of the TGP S1 switch to ON position (Refer to Switch/Jumper 2-2).
20. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press FAST and RANGE keys together on the Gantry Switch Panel.
Check that CHANGE LED is OFF.
21. Set the T6 switch of the TGP S1 switch to OFF position. ( Do NOT touch the T2 switch )
22. Press the Reset switch to reset the TGP board.
23. Move the table up and down to verify that the Table lowest position is set to the desired one.
NOTICE
Keep the T2 switch to ON position. If the T2 switch is set to OFF position and the RESET
switch is pushed, the table lowest height will be returned to the default position.
3-2 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 1 5116376
3-3-1 Adjustment
1. Move the Table to the highest position.
2. Move the Cradle to the IN-limit position desired.
WARNING
PATIENT INJURY!
WHEN SHORT-FOOT-PRINT FUNCTION IS USED, A MINIMUM CLEARANCE OF 120 MM
MUST BE DEDICATED TO PREVENT THE PATIENT FROM PINCHING BETWEEN TABLE AND
WALL. SEE ILLUSTRATION 3-1.
3. Set the T6 switch of the TGP S1 switch to ON position (Refer to Switch/Jumper 2-2).
4. Push TEST1 switch on the TGP board until the height display on the Gantry Display indicates ‘036’.
5. Set the T4 switch of the TGP S1 switch to ON position (Refer to Switch/Jumper 2-2)
6. Push TEST2 switch on the TGP board.
If CHANGE LED is lit, press FAST and RANGE keys together on the Gantry Switch Panel.
Check that CHANGE LED is OFF.
7. Set the T6 switch of the TGP S1 switch to OFF position. (Do NOT touch the T4 switch )
8. Press the Reset switch to reset the TGP board.
9. Move the cradle OUT and IN to verify that Cradle IN-limit position is set to the desired one.
NOTICE
Keep the T4 switch to ON position. If the T4 switch is set to OFF and the RESET switch is
pushed, the Cradle In Limit will be returned to the default position.
3-3 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
blank
3-4 TABLE
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
DAS/DETECTOR
TABLE OF CONTENTS
SECTION PAGE
i DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
ii DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
1-1 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
1-2 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
Precondition
Ensure that the DAS/Detector has been powered ON for at least ten minutes prior to performing the following
procedure.
1. Perform an axial scan with no x-rays (i.e., acquire a raw data file consisting of offset data):
a. Select Offline Scan; refer to below:
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A side. (A channel)
c. Select the raw data file (Acq No: 1) from the Raw data browser lists.
d. Perform Fan Data with the following settings:
e. Select Active Mean from Select Type Data; then perform Store to File.
f. Save vector with the following settings:
1-3 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
Minimum 100
Maximum 4000
j. Repeat a, b, c.
k. Select Active SD from Select Type Data; then perform Store to File.
o. Select Plot and set the Manual Select value with the following settings:
Minimum xxx
Maximum xxx
1-4 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A side. (A channel)
c. Select the raw data file (Acq No: 1) from the Raw data browser lists.
d. Perform Fan Data with the following settings:
e. Select Active Mean from Select Type Data; then perform Store to File.
f. Save vector with the following settings:
i. Select Plot and set the Manual Select value with the following settings:
Minimum -4
Maximum +4
Ch1~Ch691 Ch693~695
Active Mean -4~+4 -4~+4
1-5 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
o. Select Plot and set the Manual Select value with the following settings:
Minimum xxx
Maximum xxx
1-6 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
2-1 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
2-2 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
Precondition
Ensure that the DAS/Detector has been powered ON for at least ten minutes prior to performing the following
procedure.
1. Perform an axial scan with no x-rays (i.e., acquire a raw data file consisting of offset data):
a. Select Offline Scan; refer to below:
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A side. (A channel)
c. Select the raw data file (Acq No: 1) from the Raw data browser lists.
d. Perform Fan Data with the following settings:
e. Select Active Mean from Select Type Data; then perform Store to File.
f. Save vector with the following settings:
2-3 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
Minimum 100
Maximum 1000
j. Repeat a, b, c.
k. Select Active SD from Select Type Data; then perform Store to File.
o. Select Plot and set the Manual Select value with the following settings:
Minimum xxx
Maximum xxx
2-4 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
Service Menu → Diagnostics → Generic System Analyzer (GSA) → Format Raw Data
b. Select A side. (A channel)
c. Select the raw data file (Acq No: 1) from the Raw data browser lists.
d. Perform Fan Data with the following settings:
e. Select Active Mean from Select Type Data; then perform Store to File.
f. Save vector with the following settings:
i. Select Plot and set the Manual Select value with the following settings:
Minimum -4
Maximum +4
Ch1~Ch691 Ch693~695
Active Mean -4~+4 -4~+4
2-5 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
o. Select Plot and set the Manual Select value with the following settings:
Minimum xxx
Maximum xxx
2-6 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
1 4 7
0V_A 2 5 8 0V_L
3 6 9 0V_A 1106
1107
GND 1108
-5V_A -12V_A Nut(x4)
DAS POWER CABLE CONNECTOR
3-1 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
3-2 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
Nut (x6)
5V 24V RTN
3 6 9 12
+5V_A 5V_L
RF Power Cable
1 4 7 0V
3-3 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 16 5116376
3-4 DAS/DETECTOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
X-RAY GENERATOR
TABLE OF CONTENTS
SECTION PAGE
i X-RAY GENERATOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
blank
ii X-RAY GENERATOR
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
1-1 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
Numeric indication
1-2 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 6 5116376
l. Verify that Max of Active Mean data is within specifications as described below:
Note
You can also display the data as a numerics using Numerical button.
- Max of Active Mean (For MDAS):300000 ≤ ≤ 600000 (Specification)
- Max of Active Mean (For GDAS):700000 ≤ ≤ 1100000 (Specification)
3. Repeat steps 2 for B Side (B channel).
1-3 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
1-4 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
SECTION 2 - KV AND MA
2-1 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
Time Thickness KV mA
1.5 or 2.0 sec 5 mm 120 20 40 60 100 160 200
140 20 40 60 100 160 -
Stationary Scan (Present Degree)
(Other scan parameters): (defaults)
2-2 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
CAUTION
Electric shock! Use a ground bar to discharge the high voltage connector any time you
disconnect it.
HV Divider
HV Tank
2-3 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
X-Ray Tube
HV Tank
2-4 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
KV Read
3. Connect a digital multimeter to the output terminals of the HV divider.
(The multimeter should be in the DC voltage measurement mode)
Place the multimeter so that it can be read from the Operator’s room.
NOTICE
Do not switch ON the Rotation switch at the Gantry rear base.
4. Perform x-ray exposures and read the KV values:
a. Switch ON the ‘Slip Ring 115V‘ and ‘XG Power‘ switches at the Gantry rear base.
b. Perform scans described in Table 2-2, following the steps below, and verify that the KV readings are within
the specifications.
i. Select Offline Scan; refer to below:
Service Menu → Diagnostics → Offline Scan
ii. Select Stationary from ‘Technic - [Scan Type]‘.
iii. Set the scan parameters according to Table 2-2.
KV mA KV Specification
120 200 111.6 ≤ ≤ 128.4
140 160 130.2 ≤ ≤ 149.8
Stationary Scan (Present Degree)
Scan Time: 3.0 sec
Thickness: 2mm
Focus: Large
(Others): (defaults)
2-5 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
2-3 MA CHECK
1. Preparation:
a. Perform Warm-up scans, if the x-ray tube is cold.
b. Wait five minutes or more following the last scan prior to proceeding to the next step.
c. Switch OFF the ‘Rotate‘, ‘XG Power‘, and ‘Slip Ring 115V‘ switches at the Gantry rear base.
d. Wait at least 2 minutes, and remove the front, right side, and left side covers of the Gantry.
e. Switch ON the Service switch on the SUB Board.
f. Rotate the Gantry by hand in the clockwise direction until the x-ray is positioned at the 12 o’clock position.
g. Switch OFF the Service switch on the SUB Board.
2-6 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
SH3
SH4
C8
KV Measure Board
Probes
KV Cont Board
2-7 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 1 5116376
MA Check
5. Set the multimeter to the DC voltage measurement mode (mV).
Place the multimeter so that it can be read from the Operator’s room.
NOTICE
Do not switch ON the ‘Rotate‘ switch at the Gantry rear base.
6. Perform x-ray exposures and read the voltage values:
a. Switch ON the ‘Slip Ring 115V‘ and ‘XG Power‘ switches at the Gantry rear base.
b. Perform scans described in Table 2-3, following the steps below, and verify that the mA measurements
([measured voltage (mV)]/[5 (ohms)]) are within the specifications.
i. Select Offline Scan; refer to below:
Service Menu → Diagnostics → Offline Scan
ii. Select Stationary from ‘Technic - [Scan Type]‘.
iii. Set the scan parameters according to Table 2-3.
KV mA mA Specification
120 200 190.0 ≤ ≤ 210.0
140 160 152.0 ≤ ≤ 168.0
Stationary Scan (Present Degree)
Scan Time: 3.0 sec
Thickness: 2mm
Focus: Large
(Others): (defaults)
2-8 XG
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 19 5116376
TABLE OF CONTENTS
SECTION PAGE
i SWITCH / JUMPER
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 19 5116376
TABLE OF CONTENTS
SECTION PAGE
ii SWITCH / JUMPER
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK/ADJUSTMENT
REV 20 5116376
1-1 GENERAL
WARNING
ELECTRICAL SHOCK HAZARD !
IF THE SYSTEM HAS UPS ASSY, MAKE SURE YOU TURN OFF THE UPS POWER BEFORE
YOU ACCESS THE OPERATOR CONSOLE.
NOTICE
Cut power before removing or inserting any of the boards or plugs.
NOTICE
Electrostatic discharge. It is essential to link yourself to ground potential by wearing an anti-
static wrist strap. No board should ever be accessed without this precaution.
J4
J3
JP1VIO1 JP2VIO1
J6
J7
PSON1
5V
5V
SW1
Connectors SW2
Card Edge
Connector
Switch
• SW2 - Normally set to ‘0H’ as illustrated below.
ON `1'
`0'
1 2 3 4
Switch Description
Bit 1 Order: Determines the way DAS data is packed.
Bit 2 Endian: Determines the data endian for the PCI bus.
Bit 3 AUX: Determines how the AUX register is used.
Bit 4 Not defined.
RearCN1 (2140183-2)
JP4 JP5
JP3
JP2
JP1
JP7
JP6
JP9
JP8
REAR CN1 ASSY
SAFEON OFF
JP1
Setting Description
SAFEON Enables software to control the safety loop.
OFF Disables software to control the safety loop.
The safety line is always connected on the REAR CN1 board.
JP2, 4, 5
Jumper Description
J2 for Auto Voice Close:
When the volume dial on the keyboard is set to the minimum end, the OC
speaker volume becomes zero.
Open:
Though the volume dial on the keyboard is set to the minimum end, the OC
speaker volume does not go down beyond a set minimum level.
J4 for To Patient
J5 for From Patient
JP3
ON
NRM
OFF
T T
JP6 JP7
FAN
JP8 JP9
Jumper Description
RearCN1 (5237815)
JP4 JP5
JP10
JP3
JP2
JP1
JP7
JP6
JP9
JP8
REAR CN1 ASSY
1 2 3
1-3-2 DASIFN
J3
JP6
JP5
JP4
JP8
S2
S1
DASIFN ASSY
JP3
JP2
JP1
JP7
Switch
• S1, S2 - Normally set as illustrated below.
ON
1 2 3 4
Jumper
• JP1~JP6 - Normally set as illustrated below.
JP8
95M buad
110M buad
Slice B Slice A
J9 J2
J1
JTAG Connector
J6
JP8
S2
ON
OFF
Rec
eive
r
FPGA Download
Connector S1 TX
RX HeartGate
J7 OFF
ON J4
Switch
• S1, S2 - Normally set as illustrated below.
S1 S2
ON ON
OFF OFF
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
3 2 1
JP8
95M buad
110M buad
JP1 JP2_disable
(remove the block)
4 3 2 1
DC Power Connector
SCSI Connector
B1 B12
A1 A12
Jumper Function Description
Terminator Power
Enable Terminator
Device Type
Enable Fast SCSI
Disable Manual Eject
Force Verify for Write Command
Disable Auto Spin-up
Disable Write Cache
Disable SCSI Parity
SCSI ID0
SCSI ID1
SCSI ID2
Note: Settings
No jumper socket means the function is OFF.
SCSI ID: 3
Disable SCSI Parity: OFF
Disable Write Cache: ON
Disable Auto Spin-up: OFF
Force Verify for Write Command: ON
Disable Manual Eject: OFF
Enable Fast SCSI: ON
Device Type: OFF
SCSI Terminator: OFF
SCSI Terminator Power: OFF
A9/B9 Enable Fast SCSI Shorting pins enables Fast SCSI mode.
Open pins, the drive responds as an optical memory device
A10/B10 Device Type (type 7) (Factory default). Shorting pins, the drive responds
as a direct access device (type 0).
This functional switch informs the drive whether to adapt the
A11/B11 Enable Termination internal SCSI active terminator. Shorting pins enables the
SCSI termination.
A12/B12 Terminator Power Shorting pins enables the SCSI TERMPWR signal.
Pins
SCSI ID
A1/B1 A2/B2 A3/B3
0 OFF OFF OFF
1 OFF OFF ON
2 OFF ON OFF
3 OFF ON ON
4 ON OFF OFF
5 ON OFF ON
6 ON ON OFF
7 ON ON ON
ON
ON
S502
OFF
1 2 3 4 5 6 7 8
ON
S501 ON
OFF
1 2 3 4 5 6 7 8
1-5-1 NAA1
NAA1 ASSY
JP1
JP3
VR1
JP2
JP4
JP3, 4
Jumper Description
JP3 for Line1+ Sets an input impedance for the line input,
Line 1+ or Line2+.
JP2 Lo
Hi
Position Description
Hi Sets the volume to High.
Lo Sets the volume to Low.
JP1
FG< >GND
Setting Description
VR1
Setting Description
JP1 (Opened)
LED Functions:
• LED - Flashes 3 times when pushing SW.
• LED - “on” when Host Computer is failed to control power on.
SECTION 2 - GANTRY/TABLE
NORMAL
SWITCH FUNCTION
SETTING
Powers On/Off the gantry axial motor and servo amplifier with
Rotate ON
AC 200 V.
Powers On/Off the x-ray generator on the gantry rotaries frame
XG Power (Safety Loop) ON with three-phase 380 480 V by closing/opening the Safety
Loop.
Powers On/Off components (including TGP board) on the
Table/Tilt ON
gantry stationary frame and the table with AC 115 V.
Powers On/Off components on the rotative frame (DAS,
Slip Ring 115V ON
Temperature Controller, OGP board, etc.) with AC 115 V.
NOTICE
Avoid frequent switching ON/OFF of the XG Power switch (more than on On/Off per minute),
otherwise which will cause overheat in the x-ray generator and the Power Distribution Unit
(PDU), due to repeated charge/discharge of capacitors in them.
NOTICE
While the XG Power switch is switched ON, avoid frequent switching On/Off of the Table/Tilt
switch (more than one On/Off per minute), otherwise which will cause overheat in the x-ray
generator and the PDU, due to repeated charge/discharge of capacitors in them.
2-2 TGP
2-2-1 TGP
ON
OFF
SW1 SW5
RESET
JP3
DS9
EMRG RESET
S2 DATA CHG LED TEST1
JP6 JP4 TEST2
JP5 G1 G8
JP2
S1 S3
T1 T8 M1 M8
JP1
Jumper
• JP1, JP2, JP3, JP4, JP5, JP6 - Normally set as illustrated below.
normal
not
JP3
DETECT DETECT
JP6
JP1 JP2
IHHC NORMAL
JP4
or
not Option Normal
DETECT DETECT JP5
Note: Some Jumpers
might be NOT existed,
with lock
JP2
depending on the TGP
board.
Dip Switches
• S1, S2, S3 - Normally set as described in Tables 2-2 and 2-3.
OFF
WARNING
UNCONTROLLED GANTRY RESPONSE! CONFIRM THAT THE DIP SWITCHES ON THE TGP
BOARD ARE SET AS DESCRIBED ABOVE, UNLESS OTHERWISE SPECIFIED. IF ANY OF
THE SWITCHES ARE SET TO ON, THE GANTRY MIGHT BEHAVE DANGEROUSLY.
Normal
Switch Description
Setting
When set to ON, disables the temporary halt function of table up or gantry
T1 OFF
tilt operation.
OFF or When set to ON, the lowest table height allowed can be changed. For
T2
ON details, see the Table tab.
When set to ON, disables the interlock function of table up/down and
T3 OFF
S1 gantry tilt.
OFF or When set to ON, the most extended cradle In-position allowed can be
T4
ON changed. For details, see the Table tab.
T5 OFF (Not used)
T6 OFF When set to ON, Table/Tilt off-line test programs can be executed.
T7 T8 OFF (Not used)
TGP BOARD
HOME
SPD1
SVE
OFF
MID
MNL FIX SPD0 SLOW 90
NOTICE
Except in emergency, do not set the SYS/OFF/MNL switch to OFF while the gantry is
rotating, or the static brake will be damaged.
NOTICE
Repeated acceleration and deceleration operations of the gantry over a limited period of
time with these service switches may cause an Overload Alarm state or overheating of the
energy dissipation resistor in the servo amplifier.
When doing the operations, take a pause of approximately 20 seconds before changing the
speed.
Note
If the gantry is continuously rotated by the ABT position of the ABT/SVE/FIX switch, this may cause
an overflow of the azimuth counter on the TGP board, resulting an abnormal operation of the gantry.
If this occurs, press the reset button on the TGP board.
SYS
SYS
OFF The gantry and table are controlled by system.
(Normal Position)
MNL
SPD2
SPD1
SPD0
SLOW 15 sec/Rev 3 sec/Rev 1.0 sec/Rev
FAST
MID
SLOW
MID
10 sec/Rev 2 sec/Rev 1.0 sec/Rev
(Normal Position)
FAST 5 sec/Rev 1.5 sec/Rev 1.0 sec/Rev
The rotation speed is determined by a combination of the two switch settings as
described above.
SWITCH
SWITCH FUNCTION
POSITION
CNT
CNT Continuous rotation
HOME
905
HOME
Home (zero degrees) position
(Normal Position)
90 90 degrees position
Push Switches
• SW6 - RESET - Resets the gantry.
• SW7 - TEST1 - Increments the program No. of the TGP off-line test.
• SW8 - TEST2 - Used in the TGP off-line test.
• SW9 - EMRG RESET - When power supply for the gantry and table is cut off by an emergency switch,
the switch SW9 restores the power supply.
NOTICE
While the XG Power switch is switched ON at the gantry rear base, avoid performing
frequent alternate operations of Emergency OFF - Reset - Emergency OFF - Reset - ... (more
than one operation / minute), otherwise which will cause overheat in the x-ray generator and
the Power Distribution Unit (PDU), due to repeated charge/discharge of capacitors in them.
HOME
SPD1
OFF
SVE
MID
SW1 SW2 SW3 SW4 SW5 SW6
MNL FIX SPD0 SLOW 90
RESET
SW9
EMRG DS9
RESET
SW7
TEST 1
SW8
TEST 2
S5
ON
OFF
JP2 S1 S3 S2
ON ON ON
JP3
JP12
JP1
Jumper
• JP1, JP2, JP3 and JP12 - Normally set as illustrated below.
JP1 JP2
JP3
WITH
LOCK
JP12
NORMAL RESERVED
GANTSW
NORMAL
Dip Switches
• S1, S2 and S3 - refer to previous TGP dip switches for functional description.
• S5 - Keep default setting.
Service Switches
• SW1~SW5 - Same as previous TGP service switches.
Push Switches
• SW6~SW9 - Same as previous TGP push switches.
2-3 SUB BD
SUB BD ASSY
SW1
SW2
2-4 OGP
CN7
CN2
S3 S5
S4
ON ON ON
S3 1 8 S4 1 8 S5 1 8
Reset Power
S2
J4
OFF ON
S3
U26 U17
OFF ON
S4
U16
CN5
CN8 CN9 CN6
ON
S3
Ignore
2-5 NAA2
NAA2 ASSY
JP2
JP1
VR1
JP1
Jumper Description
Sets an input impedance for the line input
Line 1+.
JP1 for Line1+
Shorted: Sets Low Impedance (680 ohms).
Open: Sets High Impedance (22 kohms).
JP2
FG< >GND
Setting Description
Connects the NAA2 board analog ground to
Short
the frame ground.
Disconnects the NAA2 board analog ground
Open
and the frame ground.
• VR1 - From Patient Intercom Volume - Normally set as illustrated below (Center).
VR1
Setting Description
Counterclockwise Sets the volume quieter.
Clockwise Sets the volume louder.
2-6 TBL BD
JP1
TBL BD ASSY
1 2 3
JP1
no IMS
with IMS
SW3SW4
SW1
SW2
SW5 CN3
CN2 CN1
NOTICE
Return SW4 setting to ‘Normal Mode’ for customer use if it’s changed during service opera-
tion.
• SW1, SW2 - Manual temperature setting, set as illustrated below.
SW1 SW2
o
20 C 2 0
...
o
35 C 3 5
...
o
40 C 4 0
CN4
J1
S1
CN3 CN2 CN1
Power
Connector Fiber
JP2
DCP2 Board
JP1
Jumper
JP1 2
1 2 3 ROM 3
JP2
JP1 2~3, Normal PIN Boot from the on-board flash ROM
JP2 2~3, Normal PIN Boot from the on-board flash ROM
Not used
J1
J3
OFF
ON
DS1 DS2
J4
DS3 SW1 J5
Switch
• SW1 - Normally set as illustrated below.
SW1
ON
1 2 3 4 5 6 7 8 OFF
Note
SW1-5 is only effective when SW1-4 is ON state (in test mode).
Open Close
LED
• LEDs - set as table below
4-1-1 Illustration
CAUTION This board forms part of the oil seal of the High Voltage Tank. It can only be
removed at the factory. The Field Replaceable Unit (FRU) is the complete HV Tank.
LF
C
SF
4-1-3 Fuses
None.
4-2-1 Illustration
DC
160v LF Common
SF
4-2-3 Fuses
None.
4-3-1 Illustration
DC bus Common
Main
DS6
DC bus
4-3-3 Fuses
None.
4-3-4 J2 Wiring
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16
115V
sense
Fan, 115v AC
Line input
Fan, 115V AC
Line output X-ray tube
Thermal safety
4-4-1 Illustration
HIGH VOLTAGE AND HOT SURFACE: DO NOT TOUCH BOARD UNTIL INDICATOR
DANGER
NE1 (NEON - ORANGE) GOES OUT.
4-4-3 Fuses
None.
DC bus
- 400
160V
DC
0
4-5-1 Illustration
HIGH VOLTAGE: DO NOT TOUCH BOARD UNTIL DS300 ON THIS BOARD and DS1
DANGER
on Dual Snub board are out.
CAUTION
Hot surface on transformer T300 and heat sink.
DS300
DC bus DS300 - Neon (Orange) -
Presence of voltage on DC
bus for Flyback Converter to
create power supplies for
both Gate Commands
mand running
Inverter
current ILP
feedback
ILR
ning
DS102
DS101
* Insulated Gate
Bipolar Transistor
4-5-3 Fuse
None.
4-6-1 Illustration
4-6-3 Fuses
None.
4-7 IF BOARD NP
Service
Laptop
System I/F
System I/F
4-7-2 Fuses
None.
4-8-1 Illustration
SWITCH OR FUNCTION
JUMPER
RST RESET PUSH BUTTON
4-8-3 Fuses
None.
REFERENCE DESIGNATION
U32 NON VOLATILE PARAMETERS RAM (BATTERY INCLUDED)
4-9-1 Illustration
HIGH VOLTAGE: DO NOT GO INTO GENERATOR UNTIL DS1 (NEON - ORANGE)
DANGER
GOES OUT.
CAUTION
Some components on this board can become very hot.
DC Bus to inverter DC Bus out
F1 - Fuse -
DS1 - Neon Protects (on DC Bus):
(Orange) - Indi LV Power Supply 3 Phase Board
cates presence Rotor Board High Speed
of voltage on the Gate Command Board
DC Bus. Type: 15 A, 600 VDC
4-9-3 Fuses
JP1 K5 K7
K19 K6
JP2 K9 K24
• JP1, JP2 - Set a jumper plug according to the following table. This table describes that the JP2 jumper
on the TGP board equipped on the gantry may also be changed.
Refer to Section 2-2, TGP.
Jumper Setting
Part No. of RMT CNT Part No. of TGP: Part No. of TGP: Part No. of TGP:
2234978 or later 2285983 or later, 2299713 or later
JP2 on TGP: JP2 on TGP: JP2 on TGP:
Set a plug across pins 2-3 Set a plug across pins 2-3 Set a plug across pins 2-3
2301670 (DETECT) (DETECT) (DETECT)
JP1, JP2 on RMT CNT: JP1, JP2 on RMT CNT: JP1, JP2 on RMT CNT:
Set a plug across pins 1-2. Set a plug across pins 1-2. Set a plug across pins 1-2.
Direct Current
Emergency Stop
A-1
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 2 5116376
Type B
417-5009 Standby
Start
Table Set
Abort
Intercom
Warning sign :
Radiation of Laser Apparatus
A-2
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 2 5116376
Symbol Description
Microphone (Mic)
Contrast
Brightness
-10C
Humidity 10-90%
Excluding Condensation
A-3
HiSpeed Dual, ProSpeed FII
GE HEALTHCARE FUNCTIONAL CHECK / ADJUSTMENT
REV 2 5116376
CLASS 1 EQUIPMENT
Any permanently installed equipment containing operator or patient accessible surfaces must provide backup
protection against electric shock,in case the BASIC INSULATION fails. In addition to BASIC INSULATION,Class1
equipment contains a direct connection to a PROTECTIVE(EARTH) CONDUCTOR which prevents shocks when a
person touches a broken piece of equipment or touches two different equipment surfaces simultaneously.
TYPE B EQUIPMENT
CLASS I, II, or III EQUIPMENT or EQUIPMENT with INTERNAL ELECTRICAL POWER SOURCES provide an
adequate degree of protection against electric shock arising from (allowable) LEAKAGE CURRENTS or a
breakdown in the reliability of the protective earth connection.
ORDINARY EQUIPMENT
Enclosed EQUIPMENT without protection against the ingress of water.
OPERATION 0f EQUIPMENT
CONTINUOUS OPERATION WITH INTERMITTENT LOADING.
Operation in which EQUIPMENT is connected continuously to the SUPPLY MAINS.The stated permissible loading
time is so short that the long term on-load operating temperature is not attained.The ensuing interval in loading is,
however, not sufficiently long for cooling down to the long term no-load operating temperature.
EQUIPMENT not suitable for use in the presence of a FLAMMABLE ANESTHETIC MIXTURE WITH AIR or WITH
OXYGEN or NITROUS OXIDE
CLEANING
The system is NOT WATERPROOF. It is NOT designed to protect internal components against the ingress of
liquids.Clean external system surfaces(Gantry,table,consoles and accessories)with a soft cloth dipped in hot water
and wrung DAMP/DRY. (NOT dripping!) IF NECESSARY, use only mild (dish washing liquid) soap to remove dirt.
NOTICE
Avoid damage to equipment! Some “spray and wipe”cleaners etch and permanently cloud
clear plastic surfaces!! Use only warm water and mild liquid soap to clean surfaces.
A-4
www.gehealthcare.com
Imagination at work