Professional Documents
Culture Documents
Imtiaz Ahmed Dated 02-12-2023
Imtiaz Ahmed Dated 02-12-2023
Career Summary
Dynamic and collaborative RF and mmWave Design Engineer with 07 years of experience leading design,
development and Testing of high frequency sensing systems
Analog RF experience from 30 MHz to 10 GHz in design, analysis and development of wide spectrum RF and
mmWave modules including GaN/GaAs based solid-state power amplifiers with DC bias sequencing,
Transmit/Receive Modules, LO modules and multi-channel Receivers
Versed in radar systems technology with advanced knowledge of module and board-level design
Experience with RF measurement instruments including VNAs, Spectrum Analyzers
To seek and maintain a full-time position that offers professional challenges utilizing interpersonal skills,
excellent time management and problem-solving skills
Experience
Sep 2019- Present Director Technical Manager at Destined Engineering .Co
Page1
CAD simulations for power matching and bias network design
amplifier stability, Harmonic Balance, single-tone/two-tone analysis for IMD
performance
PCB layout and mechanical housing design
DC bias sequencing modules for RF power amplifiers
bench tuning for maximum power output and reduction of spurious signal up to 85
dBc at design frequency
Aug 2013 – Aug 2017 Technical Assistant Manager at Space and Upper Atmosphere Research
Commission (SUPARCO), Karachi
RF, microwave and high-speed PCB design in Keysight ADS, Altium designer and
Cadence orCAD
Simulations in MATLAB, ADS Momentum and Proteus Design Suite
Feb 2019 - Jul 2019 Teaching Assistant, Electrical Engineering, Mathematics and Computer Science
(EEMCS), TU Delft
Assisted course instructors during “Systems Engineering” course management for
1st year MSc students with responsibilities of assignments and grades for course
examinations
Academics
Sep 2017 – Aug 2019 Telecommunications & Sensing Systems, Master’s degree (8.35/10)
Delft University of Technology, Netherlands
Fundamentals of Electromagnetics, radio wave propagation, RF system design
Antenna Systems and Applied Electromagnetic Analysis in Wireless, Microwave and
Radar Engineering
Experimentations with Texas Instruments 77 GHz Automotive radar modules and
MATLAB data processing scripts for range-Doppler, range-angle and micro-Doppler
spectrogram plots
Master thesis on Advanced Space-Time Adaptive Processing (ASTAP) radar system
characterization and end-to-end system level digital calibration for compensating
system imperfections
Jan 2009 – Dec 2012 Electronic Engineering, Bachelor's degree (79.15%)
NED University of Engineering and Technology (NEDUET), Karachi, Pakistan
Circuits simulations, PCB design and development
Hands-on experience with microcontrollers
Bachelor thesis on pulse compression techniques with radar receiver
Publications
IEEE CAMA Nov-2021 Experimental study on multi-channel waveform agile beamforming and
testbed calibration https://ieeexplore.ieee.org/document/9703587
Page2
Abstract— a novel 8Tx-1Rx multi-channel waveform agile radar testbed with agility for
synthesizing and transmitting independent waveforms using Arbitrary Waveform
Generator (AWG) is developed. Hardware imperfections influence on digitally created
waveforms is studied experimentally. An end-to-end system-level digital calibration
prior to transmission is proposed. Calibration accuracy for waveform transmit ambiguity
functions, orthogonality in MISO transmissions, received signals separation and
beamforming process is examined and quantified. Extraction of the signals
corresponding to each transmit channel from the composite received signal exploiting
waveforms orthogonality is studied experimentally.
Page3
Knowledge of high efficiency power amplifiers architecture, design and characterization of RF products
Good knowledge in ADS and Momentum software
Solid experience with RF laboratory equipment and measurement techniques
Solid teamwork experience involving multiple sites
Computer programming knowledge appreciated
Good communication skills with the customer and all layers of the organization, both verbal and written in
English are mandatory
A look into the life of an RF Application Engineer
Provide the technical support to facilitate the integration of Ampleon’s products within the
customer’s application
You will be in charge to characterize new products in our RF Lab (Spar, Load-Pull, power
sweep, ruggedness, temperature drift)
Provide measurements results and test reports for new products during the evaluation phase
Analyze the results and contribute to the selection of the best design variant
Collaborate with the product engineer for the development of the production test board
Your Profile
Page4
Engineer’s or master’s degree in RF electronics
Familiar with board assembly and hands-on experience with manual soldering
Team player, contribute to a good working atmosphere, autonomous and sense of initiative
Required Education and Experience Senior Systems and Applications Engineer (Radar) (m/f/d)
Page5
At least 3 years of relevant experience
Ability for interdisciplinary problem solving and handling complex technical subjects
Understanding RF, analog and digital transistor level circuits, simulation, PCB/IC layout design techniques
Lab skills for handling, testing and debugging of embedded systems
Knowledge in RF or mmWave design and measurements methodology are highly beneficial
Microcontroller or PC (C/Python/Matlab) programming skills are highly beneficial
Experience with Cadence Virtuoso or Keysight ADS is advantage
Page6