‘THE SCALE OF
‘THIS MODEL IS
1/84 ACTUAL SIZE
on
54"
"16¢ Made in Germany by Revell Plastice GmbH, 498 Bande
NORTH AMERICAN
ASSEMBLY INSTRUCTIONS FOR YOUR X-15
FOR REST RESULTS, READ THIS FIRST TIS 15 VERY IMPORTANT
1. Since tis Kt is molded of styrene plastic, 4 start with Ho. 1 an cement it to No.2, et 6 With Revell Paint Set Colas, paint al the
tavony Revell Cement Do fat at coment parts whore inated and alow to dy before
teach Jouroys, tain rela Seem Al cols ave Hoge oy sewn
2 Aol cement sprint. Ecess cement may 5. A pas are mnbered for cay identi Cas
fon nd ange eas on sour os Haar he tuba: enred ona br 7, Disetions for aonyiag ecsls ste onthe
3. Caetly im ary mes plas om parts nes hepa area emo eck back ofthe Ged Shes
2 iy ee a ba rm tba ony when tha partite 4 Gaetly flow these cunered steps, for
ft SE ES a used. e ‘ease in building your model.
Iiting togetnar pertosty, and also enable
moving parts to move ireey,
ICH eNOINE Hale LEFT ENGINE Hat ENGINE oaP
Ngive SomUsT
PAINT ALL DETAILS, AS SHOWN AND LET DRY BEFORE ASSEMBLING
Cement Patt 1 onto Part 2, as shown, Nest coment Part 2 into Fart 3, then set
asi to ey
PRINT ALL DETAILS, AS SHOWN AND LET DRY BEFORE ASSEMBLING
Cement Parts 4 and § together. Now sement Part 8 tothe FRONT of Parts 4 end
5, then cement Part 7 to te REAR of Parts 4 and 5, as shown. Set aside to cry
youeras
Saotuet
N@) FIGHT HORIZONTAL sraatUzte
PLAGE, 00 NOT CEIMENT Parts 8 and 9 into NOTCHES in Botton Fuselage Half, 10 the FRONT of Fuselage. Next cement Pact 12 onto tne ENGINE, Assembly 2
Assembly 1, 25 show, CAREFULLY cement Part 1D dowry onto Assembly 1, Se PRESS, DO NOT CERENT Port 12 into the REAR ofthe ustlage. You may REMOVE
Sure np cerent touches Parts 8 and 9 or they Wl not move, Now cement Part 11 these parts to display the ENAINE. Appiy Decals, 2s shown then set asige 12 dy.unt
Paar
Novae vena Ftv
_——"|
Ve
woweLe vEicaL in
sun ae caTOR
Cement Parts 19 and 14 together. Now PLAGE, DO NOT CEMENT the PIN on Pacts
413.ana 14 Into the NOTCH in Part 15, then CAREFULLY cemant Part 1B fo 15. Be
sire NO CEMENT touchos PIM or Paft 1 and 14 cr these Parts will ret move
feoeiy, Let these Parts dry completly. Gement Part 17 Into Dia, 26 shown,
PLACE, D0 NOT CEMENT PIN on (2 Pars 18 te MOLES, 2s shown. Finally covert
Top Stationary Vertical Fin" Warts 18 and’ 18) to Fuselage. 2s shown. ply
Decals, a5 Shown then set aside te dry.
ONDINE Seas
Ue kro sTaUIS
unoine said Ecevses
PAINT ALL DETAILS, AS SHOWN AND LET DRY BEFORE ASSENBLING
Parts 24, 29 and 28 maybe lft off FOR MODEL IN FLIGHT POSITION,
FOR MODEL IN A LANDING POSITION. Cement (2) Parts 24 tothe Sides rient and
left of Fuselage. as shown, SNAP. DD NOT CEMENT Parts 25 into Pars 26. Next
‘SNAP, DO NOT CEMENT Parts 25 into Parts 24. Fold Lending Si Struts UP and
[AGAINST Fuselage. Apply Decals, 25 shown then set asi to dr.
TURN MODEL UPRIGHT, AS SHOWN
Cement Part 30 into Port 1, then PRESS, DO NOT CEMENT Part 21 onto the
Fuse age, Part 81 may be tomued to display the PILOT. (21 NOSE SECTIONS Ports
32 and 33 are suppled. Cement the NOSE SECTION, YOU WISH, to the FRONT
starinany
TURW ASSEMBLY 4 OVER, AS SHOWN
Gent Parts 19 and 20 together. Let Pars 18 an 20 ary completely. LACE,
0 HOT GEMENT PIN on (Farts 1 nto MOLES in FUSELAGE. NOW coment Fert
13 ard 20 onto usage. Cement Pars 72 and 23 togetier, PLAGE. UO ROT
ENE Competed ers 22 and 20 ono Fuelge, Ts Part 1s REMOVABLE
Appl Decel, a town ea Sets dy.
cron eetson
—
PAINT ALL DETAILS, AS SHOWN AND LET ORY BEFORE ASSEMBLING
OR MODEL IN FLIGHT POSITION. 00 NOT USE Parts 28 end 28 but cement Part
21 in a closed position,
FOR MODEL IN A LANDING POSITION, Cement Pert 27 to Fuselage, 28 shown,
Net SNAP, D0 NOT CEMENT (2) Parts 8 onic Part 28, then coment Park 28 Into
Fuselage
By A) ee wrosnio
ror Tuas oe
ose cone
ofthe Fuselage. Cement Part 34 into Part 35. Lot dry completely, Now PRESS,
‘Bo NOT CEMENT Part 34 inl SLOT in botiam of FUSFLABE. Apply DECALS, a¢
sionm then set aside to ary. You may splay your mel In @ STEEP CLIMB or
LANDING RPPROACH, 2: shown i the SMALL DRAWINGS.