Professional Documents
Culture Documents
Installation Manual
VERSION 3.10
P R D O X
S E C U R I T Y S Y S T E M S
IM728-728EX 961212-0000
IM728-728EX
UL has only evaluated the 708, 728, 728 EXPRESS, 738, 738 EXPRESS, 748 and
748ES for compatibility with the Ademco model 685, FBI model CP220FB, SUR-
GUARD SG-MLR2-D6 and Silent Knight model 9000.
Look for the mark on product. Only products bearing this mark are UL listed.
Some operational features are not permitted in UL installations. To respect the stan-
dards for household applications, the installer should follow these guidelines when con-
figuring the system.
1. ALL components of the system should be UL listed for the intended application.
2. If the installation is a FIRE ALARM application, refer to NFPA Standard 74 for details
on locating smoke detectors. There must be at least one UL-Listed Indoor Fire Alarm
Warning Signaling Appliance.
When the system controls a fire alarm system, wiring method must correspond to
section 32 of the Canadian Electrical Code.
Look for the mark on product. Only products bearing this mark are ULC listed.
I
IM728 -728EX
TABLE OF CONTENTS
REQUIREMENTS/GUIDELINES FOR UL, ULC AND AUSTEL INSTALLATIONS I
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
ABOUT PARADOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ABOUT THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Total compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
User-Friendly Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
False Alarm Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Flexible System Partitioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
High-Speed Preprogrammed Communication . . . . . . . . . . . . . . . . . . . 4
Event Buffer and “Real Time Clock” . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Programmable Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Espload Upload/Download Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Advanced Technology Zoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Event Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Digital Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Espload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Accessory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
BASIC INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
LOCATION AND MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
EARTH GROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PROGRAMMABLE OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
BELL/SIREN OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AUXILIARY POWER TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
KEYPAD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ZONE INPUT TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Single zone connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Advanced Technology Zone Connections . . . . . . . . . . . . . . . . . . . . . . 9
TAMPER/WIRE FAULT DEFINITIONS AND OPTIONS . . . . . . . . . . . . . . . . . 10
FIRE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TELEPHONE LINE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
POWERING-UP THE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Panel Programming Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Battery Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Battery Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INSTALLER PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-24
ESPLOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PROGRAMMABLE FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hexa programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Streamlined section programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Panel answer options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Panel Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PC Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Telephone and Account Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Computer telephone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Central station telephone numbers . . . . . . . . . . . . . . . . . . . . . . . 13
System account codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1
IM728 -728EX
2
IM728 -728EX
3
IM728-728EX
Thank you for placing your trust in the Esprit 728 EXPRESS and Esprit 728 control panels. You've cho-
sen sophisticated, user-friendly control panels designed to meet all of your technological, performance
and security requirements.
We hope that the important features of these control panels, which include a 256-event, PC-uploadable
event buffer and high-speed preprogrammed communicator formats, will simplify your task of supplying
quality security service to your customers.
ABOUT P R DOX ss
We do our best to develop technologically-advanced products. If you have any comments or suggestions,
or if you require additional technical assistance, please contact your local distributor. Every effort has
been made to ensure that your distributor's staff has received complete training from Paradox Security
Systems so that you receive prompt and effective service.
FEATURES
Reliability
The superior capabilities of the 728 EXPRESS and 728 are driven by leading edge hardware. Use of the
most powerful RISC processors on the market, with built-in “Analog to Digital” converters and SMD
Technology, means this control panel requires 30-40% less components than any previous generations.
Total Compatibility
All programming, comprehensive system features, and upload/download software of Esprit panels are
identical. This total compatibility significantly reduces the time required to conduct training, programming
and system upgrades. There’s just one set of procedures for all Esprit panels.
User-friendly Operation
The reduced number of steps required to program the 728 EXPRESS and the 728 via a keypad speeds up
installation. End-user access to most system functions calls for just one touch of the keypad. A “stream-
lined programming” feature further simplifies the programming process, by saving data automatically and
leading the installer through the programming addresses without the need to enter them manually.
4
IM728-728EX
SPECIFICATIONS
Inputs and Outputs:
Maximum Zones: 639/640 LCD and 616/626/633 LED keypads:
(See "Keypad Connections", page 8.)
728 Express: 6 zones (4 onboard zones + 2 keypad zones)
728: 10 zones (4 onboard zones + 4 ATZ zones + 2 keypad zones)
Zone Configuration: N.C. (no resistors), EOL (1 resistor), “Advanced Technology Zoning” (728 only) and
wire/tamper recognition using 1 resistors per zone. (Zone configuration address 088)
Battery Charger: 360mA with dynamic Battery test.
Aux power: 400 mA, Fuseless electronic shutdown at 1A, Automatic restore
Bell Out: 1A, Fuseless electronic shutdown at 3A, Automatic restore
AC input: 16.5 Vac, 40VA, 50 - 60Hz
PGM output: More than 1000 options to follow
2 operation modes: Timed (1 sec.- 2 hrs.) or following predetermined condition.
N.C. or N.O to ground, 50 mA Max.
Can also be remote-controlled by PC using Espload.
Serial Data Output: (1200, 1, N) for use with accessory modules (not UL systems).
Event Buffer:
256 event buffer with time and date.
Operating Modes:
49 User codes (2 Master codes) 4 or 6 digit codes.
Partitioning to System “A”, System “B”, both systems (dual area), or no system assignment (common area).
Regular, “Stay” (at Home) arming, “Double Stay” (no delay) arming, Force “Away” arming.
Fast “One key Full Arm”, “One key Stay Arm” and “One key Exit”.
Key Switch Arm/Disarm ("stay" or "regular" mode).
PS1 bedside remote.
3 keypad-activated panic alarms.
Real Time Clock for "list of events", auto arming and test reports.
Auto arm on “time” or “no zone activity delay time”.
5
IM728-728EX
Digital Communicator:
Compatible with most worldwide telecommunication standards.
Reporting formats:
Pulse: Ademco slow (10BPS), Silent Knight fast, Sescoa (20 BPS) Radionics,
Radionics with parity (40 BPS), 1400Hz - 1800Hz (10 BPS).
DTMF: Ademco Express, Ademco Contact ID (all codes and programmable), “No handshake” DTMF.
True Dial tone detection and telephone line monitoring.
Fully up/downloadable with PC.
Regular, Split and Double reporting modes.
“Programmable delay before alarm transmission”.
Espload
Upload/download PC software.
Provides fast up/download at 300 bps.
Permits creation of unlimited number of account and panel default files.
Powerful "monitoring" mode supervises all panel activity.
"Scheduler" activates panel features at preprogrammed intervals.
"Batch" mode carries out tasks following panel call.
Accessory Modules:
SRI 18: 18 PGM outputs 708: Secondary Digital Dialer (UL listed)
708DV: DVACS communicator (Canada only) Esprint: Parallel printer interface.
Keypads:
616, 626, 629 and 633 (LED) keypads. 639 and 640 (LCD) keypads, PS1 bedside remote.
(For UL systems use only 616, 626, 640 or PS1.)
Current Consumption:
(measured with battery connected, without AC and with 1KW resistor on bell and 1KW resistor on zones.)
728 Express control panel: 25mA DC 633 LED keypad: 15mA DC Typical
728 control panel: 25mA DC 35mA DC Maximum
616/626 LED keypads: 15mA DC Typical PS1 bedside remote: 15mA DC Typical
30mA DC Maximum 20mA DC Maximum
629 access control keypad: 30mA DC Typical 708 comm. module: 35mA DC Typical
55mA DC Maximum 75mA DC Maximum
639/640 LCD keypads: 20mA DC Typical 708 DV comm.module: 70mA DC Typical
70mA DC Maximum 105mA DC Maximum
SRI-18: 46mA DC Typical Esprint printer module: 35mA DC Typical
135mA DC Maximum
Select a control panel installation site that is not easily accessible to intruders. Leave at least 2” around
the panel box to permit adequate ventilation/heat dissipation. Installation location should be dry, close to
an AC source, ground connection and a telephone line connection.
6
IM728-728EX
EARTH GROUND
The earth terminal should be connected to the cabinet and
grounding rod as per local electrical codes.
AC
Use a 16.5VAC (50-60 Hz) transformer with a minimum 40VA rating
to provide sufficient AC power. Do not utilize any switch-controlled
outlets to power the transformer. UL listed systems require K12
model T16V40 transformer, ULC listed systems require Frost model
FTC 1637 transformer. Warning: Do not connect transformer
until all wiring is completed.
PROGRAMMABLE OUTPUTS
A fully programmable output (PGM1) is available on this
panel. This output can follow more than a thousand different
combinations. Please use a relay if more than 50mA is
needed.
BELL/SIREN OUTPUT
Bells or other warning devices requiring a steady voltage output during
alarms, are powered by the Bell+/ Bell- terminals. The bell output is micro-
processor-controlled and will automatically shut down if current exceeds 3
amps. The processor will allow current to resume as soon as another
alarm is triggered. The correct polarity connections should be made when
hooking up sirens (speakers with built-in siren drivers). “Bell+” terminal is
the connection for the positive lead. “Bell-” terminal is the connection for
the negative lead. The bell output supplies 12V upon alarm. It can support
two 20-watt or two 30-watt sirens. (Above 1A, battery supplies current.)
7
IM728-728EX
KEYPAD CONNECTIONS
Panel/keypad connection:
The four keypad connections labeled "red", "black", "green" and "yel-
low" should be connected to the corresponding colour terminals on the
control panel PC board.
728 EXPRESS:
Kpd 1 = Zone 5
Kpd 2 = Zone 6
8
IM728-728EX
ZONE connection, with EOL resistor, with tamper recognition and with
wire fault (short circuit) recognition (N.C. contacts) (UL/ULC Configuration)
address 088, key [MEM] = "off "
key [10] = See "Tamper/wire Fault Definitions
key [11] = and Options"
address 090, key [8] = "off"
Tamper/wire fault transmits separate code.
2 ZONES connection, without EOL resistor, with tamper recognition (N.C. contacts) (728 only)
address 088, key [MEM] = "on"
key [10] = See "Tamper/wire Fault Definitions
key [11] = and Options"
address 090, key [8] = "on"
Each zone transmits a separate alarm code.
Tamper transmits separate code.
2 ZONES connection, with EOL with tamper recognition, and with wire fault (short circuit)
recognition (N.C. contacts) (UL/ULC Configuration) (728 only)
address 088, key [MEM] = "off"
key [10] = See "Tamper/wire Fault Definitions
key [11] = and Options"
address 090, key [8] = "on"
Each zone transmits a separate alarm code.
Tamper/wire fault transmits a separate alarm code.
9
IM728-728EX
FIRE CIRCUIT
The fire zone (enabled by defining zone 3 as "24 hour”) should always be con-
W
nected with a 1K EOL resistor (PN201100200-PRT on UL systems). If there is
a line short in the fire zone, a fire alarm will be generated. If the line is "open", a
"fire loop" trouble report will be sent to the central and trouble indicator [11] will
illuminate on the LED keypad.
10
IM728-728EX
Battery Test
Panel conducts dynamic battery test under load every 60 seconds. If the battery is disconnected, or capacity
is low, trouble indicator key [1] illuminates. Key [1] also comes “on” if battery voltage drops to 10.5 volts while
panel is running on battery power (with no AC). At 8.5 volts, the panel shuts down and all outputs close.
ESPLOAD
The 728 EXPRESS and 728 can be remotely programmed with Espload upload/download software, or on
site using Espload and a ADP-1 adapter. Advanced Espload software can carry out fast upload or download,
and provides many powerful features, including a comprehensive "monitoring" mode to oversee all panel
activity, a "scheduler" to initiate preprogrammed tasks at set intervals, and a "batch" mode to carry out pre-
programmed tasks following a call from the panel. There is no limit to the number of account files or panel
defaults that can be created, and thousands of programming combinations can be assigned to the PGM out-
put using Espload. Espload can be converted to the language of your choice, and individualized help menus
can also be generated. Contact your local Paradox Distributor for your copy of Espload software.
KEYPAD
To program Esprit panels via the keypad, first complete the programming work sheets and follow the pro-
gramming procedures outlined in the "Programming Guide".
PROGRAMMABLE FEATURES
Hexa Programming:
All digits from 0 to F are valid. Programming values are programmed into memory locations from address
000 to 043 and from address 300 to 527.
1) Press [ENTER] + installer code. 4) Enter 2 digit data.
2) [ENTER] will flash (programming mode). 5) Go to step 3 for next address.
3) Enter 3 digit memory address.
To exit programming mode, press [CLEAR].
11
IM728-728EX
12
IM728-728EX
13
IM728-728EX
14
IM728-728EX
*Ground start Pulse Provides 3 sec. pulse before [5] [5]/[2] [2ND]/[8] [5] [5]/[2] [2ND]/[8]
(Timed N.O.) communication attempt.
Push key [1] and [2] Provides output when keys [1] and [1] [5]/[8] [2ND]/[6] [1] [5]/[8] [2ND]/[6]
(Regular N.O.) [2] are pressed simultaneously.
System armed Output removed when system [9] [2]/[11] [2ND]/[8] [9] [2]/[11] [2ND]/[8]
(Regular N.C.) armed.
Strobe output Provides latching output on [1] [2]/[12] [2ND]/[2] [1] [2]/[12] [2ND]/[2]
(Regular N.O.) alarm, until disarmed.
Fail to communicate Provides output upon fail to [5] [2]/[6] [2ND]/[4] [5] [2]/[6] [2ND]/[4]
(Timed N.O.) communicate for 2 minutes.
2nd telephone line relay Provides output after one failed [2ND] [7]/[10] [2ND]/[MEM] [2ND] [7]/[10] [2ND]/[MEM]
(Regular N.O.) communication attempt.
Kiss off Provides 3 sec. output after signal [5] [7]/[BYP] [2ND]/[8] [5] [7]/[BYP] [2ND]/[8]
(Timed N.O.) received at monitoring station.
Note: For other PGM operations, use Espload software by programming the desired PGM function and
pressing F8 to see the keypad programming codes and address. If other programming options are
needed, fax your requests to Paradox Technical Support at 514-491-2313.
15
IM728-728EX
16
IM728-728EX
17
IM728-728EX
Arming using PS1 or keyswitch (Address 086, key [2] and key [3])
The PS1 bedside remote arming module or keyswitch can be used to stay arm, full arm, or disarm the
system. The PS1 keyswitch is enabled at address 086, key [3].
Key [2] "off": PS1 or keyswitch "regular" arms system.
Key [2] "on": PS1 or keyswitch "stay" arms system.*
*Note: If partitioning is enabled (address 086, key [8] "on"), PS1 arms system "A" only. Use of PS1 is not
recommended for partitioned systems.
Call back (Address 086, key [4])
For extra security, the panel can be programmed to call the PC back when communication is attempted
by the PC. The panel will first answer the call, then Espload and the panel will verify identification codes.
The panel will then hang up and call the PC back and establish communication. Espload automatically
goes into the “wait for call mode”, ready to answer when the panel calls back. The identification codes
are verified again before allowing access to the panel.
Related features: “Computer telephone number” 008-015.
Auto arm
On Time: (Address 086, key [5])
The panel may be programmed to arm at the same time every day. Program both the hour and minute
(addresses 044, 045) for arming. A late closing code may be programmed (address 516).
Related features: “Auto arm” 090, [2] “Auto/Espload Arm” 300 "Auto arming" p.15.
No Movement: (Address 086, key [6])
If zone activity is not detected for a programmed period (address 055) while disarmed, the panel can auto
arm and/or send a "no movement" report (address 517). Refer also to "No movement" p. 15.
Touch tone options (Address 086, key [7])
Tone (key [7] = "on") or pulse dialing can be programmed. If "pulse" is chosen for a central station phone
number, "tone" dialing can be programmed for the other number. [BYP] ("switch from pulse to tone")
should be entered in the second phone number during programming.
Partitioning (Address 086, key [8])
Partitioning is activated, (key [8] "on"). The panel's fully programmable zones (plus 2 remote keypad
zones) can be divided into two systems. (See “System Partitioning”, page 25.)
Silent alarm (Address 086, key [9])
Key [9] "off":
Silent zones/panics generate a silent alarm. Zones defined as "silent" at addresses 096-098 and keypad
panic zones will not cause an audible alarm, however, the keypad "armed" light will flash and the alarm
condition will remain until a valid user code is entered.
Key [9] "on":
Silent zones/panics generate only a report (The red keypad LED does not flash, and there is no need to
"reset" the silent alarm.)
Silent delay zones generate an entry delay beep, and a report at the end of the entry delay.
Zone restore is always reported upon zone closure.
Memory display, auto zone shutdown are always active for silent zones when enabled at address 086, key [TRBL].
Silent alarms can be monitored by the PGM output. (Silent flag is cleared on report or disarm.)
On split reporting, silent zones/panic are reported to Telephone #1.
18
IM728-728EX
To establish communication, the communicator takes the telephone line and waits for a dial tone. If a dial
tone is identified, the communicator will dial the first central station telephone number. If a connection is
made, system report will take place and the communicator will hang up upon completion. If for any rea-
son, communication is interrupted, the communicator will dial the 2nd central telephone number and
report only the events that were not reported during the interrupted attempt.
During a communication attempt, the communicator waits for a dial tone for up to 8 seconds. Even if a
dial tone is not found, the communicator will dial the central station.*** After 60 seconds, if communi-
cation has not been established, the dialer will hang up, wait 5 seconds and try the second number. This
sequence will be repeated 8 times, switching back and forth between the 1st and 2nd number. (Regular
reporting dialing procedure: 1,2,1,2,1,2,1,2, "communicator report failure".)
***This feature is useful for PBX systems, which do not provide a dial tone. You can program the dialing
sequence required to get a line on a PBX system, and this sequence will be added before the central
station number. If there is a time delay between dialing and getting a line, this can be programmed
into the dialing sequence using the [MEM] ("pause") key.
After 8 unsuccessful attempts, the redial sequence ends and "communicator report failure" will appear in the
keypad’s trouble display (key [7] "on"). When the next reportable event occurs, (even if it is not programmed
to report to the central), the communicator will try again to establish communication. If successful, all events
stored in the event buffer that have not yet been reported will be communicated to the central.
Split reporting (Address 086, key [11] "on", key [12] "off")
All "system" reports (i.e. trouble reports, arm/disarm reports, etc.) are sent to Telephone #2, until an alarm is
generated. Following alarm generation, all activity, including alarm and restoration reports, is sent to Telephone
#1 until the system is disarmed. When there is an alarm, any ongoing communication (upload/download or
reporting to Telephone #2) will immediately be stopped and the panel will dial Telephone #1.
Alarm reports dialing procedure: (1,1,1,1,1,1,1,1, "communicator report failure")
"System" reports dialing procedure: (2,2,2,2,2,2,2,2, "communicator report failure")
Double reporting (Address 086, key [11] "on", key [12] "on")
The panel will transmit all reports to both programmed telephone numbers. If, after 8 attempts using either
number, communication is not established, "communicator report failure" will be displayed by key [7].
Double reporting dialing procedure: (1,1,1,1,1,1,1,1, "communicator report failure")
(2,2,2,2,2,2,2,2, "communicator report failure")
Note: To stop communication attempts until the next reportable event, press [ENTER] + installer code + [STAY].
Bell squawk (Address 086, key [MEM])
Bell/siren will emit a 0.5 second “squawk” once upon arming, and twice upon disarming.
(Key [MEM] "on" = enabled)
Auto zone shutdown (Address 086, key [TRBL] "on")
Key [TRBL] "on" = Zones that initiate 4 consecutive alarms during the same armed period will be automat-
ically bypassed. (Zones must be bypass-enabled at address 124.) After a zone has
been bypassed, the panel can send a "zone shutdown” report to the central (if pro-
grammed to do so at addresses 448-457).
Note: Once auto zone shutdown has been enabled, it will either be activated after 4 "zone closure"
restoration reports or 4 "bell cut-off " restoration reports, depending on which type of alarm restora-
tion code has been activated at address 088, key [BYP].
Automatic event buffer transmission (Address 088, key [2ND])
Key [2ND] "on" = system will dial the computer telephone number programmed in Section 02 and 03
(addresses 008-015) to upload the contents of the event buffer to the PC. (Espload must be in "wait for
call" mode.) The system will make two attempts to call the PC when the event buffer reaches 50%
capacity. If communication is established, the system will then proceed to report the contents of the event
buffer to the PC. Should transmission be interrupted before the complete contents of the buffer can be
19
IM728-728EX
transmitted, or if after two attempts, communication is not established, the system will wait until the event
buffer is full, before attempt to communicate with the central again.
If communication is established, the system will then proceed to report the contents of the event buffer to
the PC. If after two attempts, communication is not established, each subsequent new event will erase
the oldest event in the buffer, until the event buffer once again reaches 50% capacity.
Enable keypad panic signals (Address 088)
Key [1] "on" = Panic 1 (keys [1] and [3], PS1) enabled
Key [2] "on" = Panic 2 (keys [4] and [6]) enabled
Key [3] "on" = Panic 3 (keys [7] and [9]) enabled
Keypad panic options (Address 088)
Key [4] "off " = Panic 1 silent Key [5] "off " = Panic 2 silent Key [6] "off " = Panic 3 silent
Key [4] "on" = Panic 1 audible Key [5] "on" = Panic 2 audible Key [6] "on" = Panic 3 fire
Silent operation
When panic keys [1] and [3], OR [4] and [6], OR [7] and [9] are pushed simultaneously for 2 seconds or
PS1 is used, a single confirmation beep is sounded, codes programmed at addresses 513, 514, and 515
are transmitted and the alarm latches, flashing the keypad "armed" light until reset by a user code.
Audible operation
When panic keys are pushed in addition to alarm codes being transmitted, the alarm output (bell/siren)
will activate until reset by a user code or until the bell cut-off time (address 052) expires.
Fire operation
Same as audible operation except that bell/siren output will be pulsed (intermittent "on"/"off ").
"One key" arming enable (Address 088)
Key [7] "on" = Pushing key [10] for 2 seconds "full" arms system.
Key [8] "on" = Pushing key [11] for 2 seconds "stay" or “system A” arms system.
User/access code length (Address 088)
Key [9] "off " = 6 digit user/access codes and installer code.
Key [9] "on" = 4 digit user/access codes and installer code.
Tamper/wire fault definitions (Address 088)
Note: If key [10] and key [11] are both "off ", this means that tamper and wire faults will not be recog-
nized. See "Zone Input Terminals" page 8-9, "Tamper/Wire Fault Definition and Options", page
9-10, and "Tamper/wire Fault Definition table" in the "Programming Guide".
Beep on exit delay (Address 088)
Key [12] "on" = The keypad will sound on exit delay (except when in “stay” arming). Frequency of inter-
mittent beeps increases during the last 10 seconds of the exit delay period.
Zone restore transmission (Address 088)
Key [BYP] "off " = If zone is closed, restoration code will be transmitted after "bell cut-off".
Key [BYP] "on" = Restoration code transmitted as soon as zone is closed.
Silent zones are always restored as soon as they are closed.
Zones with EOL resistors (Address 088, key [MEM])
See "Zone Input Terminals" pages 8-9.
Always report disarm (Address 088)
Key [TRBL] "off " = always reports disarm codes.
Key [TRBL] "on" = reports disarm code only after alarm.
Exclude power failure from trouble display (Address 090, key [2ND])
Key ="on": Power failure will not make the [TRBL] key flash.
This trouble condition may still be viewed after pressing [TRBL].
20
IM728-728EX
Arming Options
Auto arm (Address 090, Key [2])
Key ="off ": When system auto arms (on time or "no movement"), "regular" arming will take place (if all
zones are closed).
Key ="on": When system auto arms (on time or “no movement”), "STAY" arming will take place (if all
zones are closed). If zone partitioning is programmed (address 086, key [8]), System “A” will
arm. (See also "Auto arming" page 15.)
Advanced Technology Zoning (ATZ) (Address 090, key [8]) (728 only)
Key = “on”: Permits the use of two zones per input. Each zone can transmit a separate alarm.
Key = “off”: Single zone per input.
21
IM728-728EX
22
IM728-728EX
All report codes are assigned to a system account, whether or not partitioning is activated. Arm/disarm
reports are assigned to System "A" when partitioning is "off", or to the system account to which they
belong, based on code priority assignment, when partitioning is activated.
Trouble and special report codes are always assigned to System "A".
Zones 7 to 24 are not available on the 728 EXPRESS.
Arming codes/disarming codes: (Addresses 300-399) SECTION 11 - 35
System access codes can be programmed to generate hexa report codes that communicate the identity of the
user arming/disarming the control panel to the central monitoring station. Each user code can be assigned an
arm/disarm report code. Auto/Espload Arm will be reported to the central when Espload is used to arm the
control panel or when the system arms itself automatically (on “no movement” or at a specified time). Espload
disarm will be reported to the central when Espload is used to disarm the control panel. Arm/disarm with mas-
ter code will be reported to the central when the master code or keyswitch is used to arm/disarm control panel.
Zone alarm codes: (Addresses 400-423) SECTION 36 - 41
Alarm report codes programmed will be sent to the monitoring station, identifying the zones that are gen-
erating alarms. Note that the 728 has 10 “alarm” zones and the 728 EXPRESS has only 6 “alarm” zones.
See the “Programming Guides” for the 728 and 728 EXPRESS.
Zone restore codes: (Addresses 424-447) SECTION 42 - 47
Zone restoration codes programmed will be sent to the monitoring station, identifying zones returning to
normal status after alarms. Note that the 728 has 10 “restore” zones and the 728 EXPRESS has only 6
“alarm” zones. See the “Programming Guides” for the 728 and 728 EXPRESS.
Shutdown codes: (Addresses 448-471) SECTION 48-53
These codes are sent to the monitoring station to identify zones bypassed during “auto zone shutdown”
(address 086, [TRBL].). Note that the 728 has 10 “shutdown” zones and the 728 EXPRESS has only 6
“shutdown” zones. See the “Programming Guides” for the 728 and 728 EXPRESS.
Tamper trouble codes: (Addresses 472-495) SECTION 54-59
These codes identify zone locations of tamper “troubles” to the central. If ATZ (728 only) is activated, the
tamper zone location reported represents a pair of zones. Note that the 728 and the 728 EXPRESS each
have 4 “tamper” zones. See the “Programming Guides” for the 728 and 728 EXPRESS.
Trouble codes: (Addresses 496-503) SECTION 60 - 61
6 trouble status codes can be reported to the central, if programmed: max. auxiliary current, bell discon-
nect/max. bell current, battery disconnected/low voltage, power failure, fire loop trouble, and timer loss. (See
"Trouble Display/Monitoring", page 27-28, for a list of trouble conditions displayed on the keypad.)
Trouble restore codes: (Addresses 504-511) SECTION 62 - 63
If trouble conditions occur and are reported, once normal status is re-established, a "restoration" code
can be transmitted to the central to indicate that the "trouble" situation has been rectified.
Note: All Tamper/Wire Faults must be restored before a “Tamper/Wire Fault” restoration code is transmitted.
Special codes: (Addresses 512-527) SECTION 64 - 67
These codes are assigned to report 11 special status conditions.
Test report Test report will be reported to the central automatically at the day and time set for the
“auto test report” (addresses 046, 047, 048) or manually. To send a manual test report,
press [ENTER], followed by installer, master or user code 1, and [BYP] are pressed.
Panic 1 Panic alarm will be reported to the central if PS1 is used or if keys [1] and [3] are
pressed for 2 seconds.
Panic 2 Panic alarm will be reported to the central if keys [4] and [6] are pressed for 2 seconds.
Panic 3 Panic alarm will be reported to the central if keys [7] and [9] are pressed for 2 seconds.
Late to close Will be reported to the central when the system has been armed or not by the required time.
No movement Will be reported to the central when there is no movement in the protected area for a
designated time period.
23
IM728-728EX
Partial arming Will be reported to the central if the control panel is armed while any zones are
bypassed or when the system is force armed.
Recent close This code is sent to the monitoring station to notify that an alarm occurred shortly after
the system was armed (during the “recent closing” delay). This feature is designed to
help prevent unneeded response from the central.
Duress A duress code is sent to the central whenever a person enters it on a keypad. This fea-
ture is primarily intended to send a silent alert if a user is forced to disarm the system
under threat. Only user 48 can use this feature.
Log-in (Espload) Will be reported to the central when communication between the panel and the PC is over.
Program change Will be reported to the central once programming mode is entered using the installer code.
The Esprit 's innovative keypads take a new approach to security features and functions. Each numeral
from 1 to 12 on the keypad represents an actual zone. When the [2ND] key flashes, the same numerals
represent a second set of 12 zones, zones 13 to 24. When the zone light is "off", the status in the protect-
ed zone is normal. If the zone light is "on", this means the zone is open.
"CONF" confirmation beep: an intermittent series of beeps indicating a successful keypad entry.
"END/REJ" end/rejection beep: 1 long tone indicates that the operation was incorrectly entered on the keypad.
24
IM728-728EX
Fast Exit
Exit while the system is armed in "stay" mode:
A: Fast exit and Stay key [11]
To exit the premises and remain "stay armed": press key [11/STAY] for two seconds. The system switches
to "exit delay" mode ("ready" LED flashes). At the end of the "exit delay" period, the system will return to
"stay" arming mode.
B: Fast exit and Regular Arm key [10]
To exit the premises and "regular" arm: press key [10] for two seconds. The system switches to "regular"
arming (key [11] and [12] flash) with "exit delay" ("ready" LED flashes). At the end of the "exit delay"
period, the system is "regular" armed.
System Disarming
The protected area should be entered through a designated entry/exit door. The keypad sounder will beep to
remind user to disarm the system. A valid access code should be entered on the keypad, before the allotted
entry time expires. If the access code is entered incorrectly, press [CLEAR] and re-enter it. The "armed" light
will extinguish and the sounder will change to the "CONF" beep (series of short beeps) before silencing.
Alarm Memory
The memory light [MEM] on your keypad will illuminate if any alarm situations took place while your system
was armed. A record of all alarm situations that occurred is stored in memory. After disarming the system,
pressing once on the [MEM] key causes it to flash and brings up, in the keypad display, the alarm events
that occurred during the last alarm period. (Alarm events consist of all zones that generated alarms.)
SYSTEM PARTITIONING
By activating the panel's "partitioning" feature, zones can be divided into two distinct systems, with a
shared fire zone (zone #3). Both systems are controlled by one panel, making partitioning a particularly
useful feature in installations where shared security systems are more practical (i.e. office/warehouse,
apartment/condo complexes).
Partitioning
Partition "on" (Address 086, key [8] "on")
Addresses 116, 120:
Zones can be assigned to system “A” (addresses 116 zone key “ON”) and/or to system “B” (addresses 120
zone key “ON”). A “common zone” is a zone that is not assigned to any system (it will be reported as “System
A” zone). It’s armed only when both systems are armed, and disarmed if system “A” or “B” is disarmed. A “dual
zone” is a zone that is assigned to both systems (it will be reported as one of the system (either “A” or” B”)). It
is armed if either system “A” or system “B” is armed, and disarmed only when both systems are disarmed.
Note: When partitioning is not activated (address 086, key [8] "off") any zones selected at address
116 will be armed upon "stay" arming.
Keypad display:
Both systems are displayed on the keypad at the same time. In partitioning mode, when System "A" is
armed, the [STAY] key illuminates. If System "B" is armed, the [AWAY] key illuminates. If both systems are
armed, both of these keys will be illuminated.
25
IM728-728EX
Arming/Disarming
Code definition: Partition "on" (Address 086, key [8] "on")
Addresses 062, 064, 066: Designates access codes that arm System "A" zones.
Addresses 068, 070, 072: Designates access codes that arm System "B" zones.
Addresses 074, 076, 078: Designates access codes that can "bypass" zones
When a code is activated at both addresses (062-066 and 068-072), it can do the following:
• The code can fully arm the system. If the code is entered when systems "A" and "B" are disarmed, it
will completely arm the system.
• The code can fully disarm the system. If the code is entered when system "A" and "B" zones are
armed, it will completely disarm the system.
• When the system is partially armed (i.e. only System "A" or "B" is armed) entering this code will arm
the other system.
• The code can be used to selectively arm/disarm System "A" or System "B" zones.
Enter [11] + code to arm/disarm System "A" zones.
Enter [12] + code to arm/disarm System "B" zones.
Note: Codes that are not selected at either address are disabled.
The master code can always access both systems and bypass zones.
• System "A" codes can stop sirens coming from System "B" zones (and vice versa), but will not disarm
the other system.
• It is not possible to arm one system during the other system's exit delay.
Note: When partitioning is not activated, (address 086, key [8] "off"):
Addresses 062, 064, 066 determines which access codes can activate "stay" arming.
Addresses 068, 070, 072 determines which access codes can activate "away" arming.
Addresses 074, 076, 078 determines which access codes can "bypass" zones.
26
IM728-728EX
27
IM728-728EX
28
IM728-728EX
“POWER-DOWN” RESET
(1) Remove battery and AC to power down the unit. (4) Wait 10 seconds.
(2) Connect a jumper between "reset jumper" pins. (5) Remove jumper.
(3) Connect AC then battery.
Factory default installer and master codes will be reinstated. Values entered at addresses 008-043, 062-126,
300-527, as well as all user codes, will be erased ([2ND] [2ND]). Programmed values of all other addresses do
not change.
WARRANTY
Warranty conditions for the ESPRIT may vary from country to country. Please consult your local dealer for
complete warranty information. In all cases, the warranty does not cover malfunctions arising from
installer error or failure to follow installation/operation instructions, nor does it apply to damages due to
causes beyond the control of Paradox Security Systems, such as lightning, excessive voltage, mechani-
cal shock or water damage.
LIABILITY
Under no circumstances shall Paradox Security Systems be held liable for any direct or indirect dam-
ages, loss of anticipated profits, loss of time, or any other losses incurred by the buyer in connection with
the purchase, installation, operation or failure of this product.
WARNING
This security system should undergo frequent testing. However, despite regular testing, and due to, but not
limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
29
IM728-728EX
PROGRAMMING INFO
30
IM728-728EX
DECIMAL DISPLAY
If key is lit = 8 = 4 = 2 = 1
Total value (57)
(8 + 1 + 32 + 16 = 57)
31
IM728-728EX
INCIDENCE OF HARM
Should terminal equipment/protective circuitry cause harm to telephone network, telephone company shall, where practicable, noti-
fy customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone
company may temporarily discontinue service if action is deemed reasonable in circumstances. In case of temporary discontinu-
ance, telephone company shall promptly notify customer and will be given opportunity to correct the situation.
GENERAL
This equipment shall not be used on coin telephone lines. Connection to party line service is subject to state tariffs.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to equipment intermittently, the user is encouraged to try to correct the interference by one or more of the following
measures: (1) reorient or relocate the receiving antenna; (2) increase the separation between the equipment and receiver; (3) con-
nect the equipment to an outlet on a circuit other than the one to which the receiver is connected, or (4) consult the dealer or an
experienced radio/tv technician for assistance.
CAUTION:
Changes or modifications not expressly approved by PARADOX SECURITY SYSTEMS could void the user's authority to
operate the equipment.
32
IM728-728EX
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain
telecommunications network protective, operational and safety requirements. The Department does not guarantee
the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not prevent degradation of service in
some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly
important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electri-
cal inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to
a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any
combination of devices subject only to the requirement that the total of the Load Numbers of all of the devices does
not exceed 100. The Load Number of this unit is 33.
Industry Canada certification is only applicable to installation of devices which include transformers approved by the
Canadian Standards Association (CSA).
Avant d'installer ce matériel, l'utilisateur doit s'assuré qu'il est permis de le raccorder aux installations de l'entreprise
locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccorde-
ment. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus n'em-
pêchent pas la dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être effectuées par un centre d'entretien canadien autorisé désigné
par le fournisseur. La compagnie de télécommunications peut demander à l'utilisateur de débrancher un appareil à la
suite de réparations ou de modifications effectués par l'utilisateur ou à cause d’un mauvais fonctionnement.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'energie élec-
trique, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette
précaution est particulièrement importante dans les régions rurales.
AVERTISSEMENT: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoit recours à une ser-
vice d'inspection des installations électriques, ou à un électricien, selon le cas.
"L'indice de charge (IC) assigné à chaque dispositif indique, pour éviter toute surcharge, le pourcentage de la charge
totale qui peut être raccordée à un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit
bouclé peut être constituée de n'importe quelle combinaison de dispositifs, pourvu que la somme des indices de
charge de l'ensemble des dispositifs ne dépasse pas 100." L'indice de charge de ce produit est 33.
La certification d'Industrie Canada s'applique seulement aux installations d'appareils utilisant un transformateur
approuvé par l'Association Canadienne de Normalisation (CSA).
33
IM728 -728EX
34