The document is from a diagnosis assistance system for a Mercedes vehicle. It lists a vehicle identification number and model information. It then provides a full list of fault codes and diagnostic events relating to issues with components, communications, voltages, and messages for that vehicle model.
The document is from a diagnosis assistance system for a Mercedes vehicle. It lists a vehicle identification number and model information. It then provides a full list of fault codes and diagnostic events relating to issues with components, communications, voltages, and messages for that vehicle model.
The document is from a diagnosis assistance system for a Mercedes vehicle. It lists a vehicle identification number and model information. It then provides a full list of fault codes and diagnostic events relating to issues with components, communications, voltages, and messages for that vehicle model.
Diagnosis Assistance System Copyright 1999 Daimler AG
VIN WDB2110701A123456 Model 164.175 ALL
series/model designation Order number License plate
Full list of fault codes and events
9001 The control unit is faulty.
9002 The installation side of the control unit has changed or is not recognized. 9003 The status of the ignition (circuit 15) is registered as implausible. 9004 Status of terminal 56b implausible 9007 The control unit data record is not coded or coded incorrectly. 9008 The headlamp data record is not coded or coded incorrectly. 9009 The vehicle data record is not coded or coded incorrectly. 900A LIN bus error 900E Local overvoltage at control unit and stepper motors 900F Local undervoltage at control unit and stepper motors 9010 Communication fault with component E1m1 (Left headlamp range adjustment motor) 9011 Component E1m1 (Left headlamp range adjustment motor) is defective. 9012 Component E1m1 (Left headlamp range adjustment motor) has Excess temperature or Undervoltage. 9013 Timeout of component E1m1 (Left headlamp range adjustment motor) or component is de-energized. 9020 Communication fault with component E1m2 (Left dynamic curve illumination motor) 9021 Component E1m2 (Left dynamic curve illumination motor) is defective. 9022 Component E1m2 (Left dynamic curve illumination motor) has Excess temperature or Undervoltage. 9023 The sensor for curve illumination is defective or component E1m2 (Left dynamic curve illumination motor) is blocked. 9024 Timeout of component E1m2 (Left dynamic curve illumination motor) or component is de-energized. 9030 Communication fault with component E1m3 (Left light distribution cylinder motor)
9031 Component E1m3 (Left light distribution cylinder motor) is defective.
9032 Component E1m3 (Left light distribution cylinder motor) has Excess temperature or Undervoltage. 9033 The sensor for the light distribution cylinder is defective or component E1m3 (Left light distribution cylinder motor) is blocked. 9034 Timeout of component E1m3 (Left light distribution cylinder motor) or component is de-energized. 9035 Component E1m3 (Left light distribution cylinder motor) has excess temperature. 9042 Control unit N51 (AIRmatic control unit) reports faulty signals from level sensors on front axle. 9043 Control unit N51 (AIRmatic control unit) reports faulty signal from level sensor on rear axle. 9050 Short circuit of ignition auxiliary voltage (outside control unit) 9051 Component E1e10 (Left bi-xenon lamp with integral ignition module) is defective. 9052 The xenon bulb is not inserted. 9053 Cable between E1n1 (Xenon headlamp control module) and E1e10 (Left bi-xenon lamp with integral ignition module) has short-circuit. 9055 Xenon output unit defective Event 9005 Communication fault with control unit XALWA-R Event 900B The control unit receives various information on the status of the ignition via signal line 'Terminal 15' and the CAN bus. Event 900C The supply voltage of the control unit is too low (undervoltage). Event 900D The supply voltage of the control unit is too high (overvoltage). Event 9040 No CAN message 'Vehicle level' from control module AIRmatic or message is faulty. Event 9060 CAN message 'Wheel speed' or 'Stop lamp switch' from control unit ESP is missing or is faulty. Event 9061 Message 'Pedal value sensor' from control unit Engine management is not available on the CAN bus. Event 9062 No CAN message 'Steering angle' from control module SCM [MRM] or message is faulty. Event 9063 No CAN message 'Status of terminals' from control module EZS or message is faulty. Event 9064 CAN message 'Main beam' or 'Light sensor' from control unit CGW is missing or is faulty. Event 9065 No CAN message 'Yaw rate' from control module ESP or message is faulty. Event 9066 One or more messages from control unit IC are not available on the CAN bus. Event 9067 No CAN message 'Transmission mode' from control module Transmission or message is faulty. Event 9069 No CAN message 'Intelligent Light System' from control module IC or message is faulty. Event 906A One or more messages from control unit Transmission are not available on the CAN bus. Event 906B CAN message 'Main beam', 'Rear foglight' or 'Low beam' from control unit CGW is missing or is faulty.
Wednesday, June 27, 2018 18:42:13 Page 2/3
12/2016 (2016-10-06) Diagnosis Assistance System Copyright 1999 Daimler AG
Event 906C CAN timeout fault
Event 9071 No CAN message 'Terminal 15X' from control module EZS or message is faulty.