Professional Documents
Culture Documents
BS en 558-2022
BS en 558-2022
National foreword
This British Standard is the UK implementation of EN 558:2022. It
supersedes BS EN 558:2017, which is withdrawn.
The UK participation in its preparation was entrusted to Technical
Committee PSE/18/1, Industrial valves, steam traps, actuators and
safety devices against excessive pressure - Valves - Basic standards.
A list of organizations represented on this committee can be obtained on
request to its committee manager.
Contractual and legal considerations
This publication has been prepared in good faith, however no
representation, warranty, assurance or undertaking (express or
implied) is or will be made, and no responsibility or liability is or will be
accepted by BSI in relation to the adequacy, accuracy, completeness or
reasonableness of this publication. All and any such responsibility and
liability is expressly disclaimed to the full extent permitted by the law.
This publication is provided as is, and is to be used at the
recipient’s own risk.
The recipient is advised to consider seeking professional guidance with
respect to its use of this publication.
This publication is not intended to constitute a contract. Users are
responsible for its correct application.
© The British Standards Institution 2022
Published by BSI Standards Limited 2022
ISBN 978 0 539 12783 6
ICS 23.040.99; 23.060.01
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 30 June 2022.
English Version
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 558:2022 E
worldwide for CEN national Members.
BS EN 558:2022
EN 558:2022 (E)
Contents Page
European foreword....................................................................................................................................................... 3
Introduction .................................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 5
4 Dimensions and tolerances ......................................................................................................................... 9
4.1 Basic series ........................................................................................................................................................ 9
4.2 Face-to-face and centre-to-face dimensions.......................................................................................... 9
4.2.1 General ................................................................................................................................................................ 9
4.2.2 Class designated valves with ring joint flanges ................................................................................. 10
4.2.3 Valves with lining ......................................................................................................................................... 13
4.2.4 Raised face flanges....................................................................................................................................... 13
4.3 Tolerances ...................................................................................................................................................... 13
Annex A (informative) Origin of basic series .................................................................................................. 46
Annex B (informative) Relationship between DN and NPS ........................................................................ 50
Annex C (informative) Overview of special basic series (compared to the previous version) ..... 51
Bibliography ................................................................................................................................................................. 53
2
BS EN 558:2022
EN 558:2022 (E)
European foreword
This document (EN 558:2022) has been prepared by Technical Committee CEN/TC 69 “Industrial
valves”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall be
withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
In comparison with the previous edition, the following technical modifications have been made:
— basic series 126, 127, 128 added and used in Table 21;
— basic series included in EN 558:2017 that are considered special transferred to Annex C.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
BS EN 558:2022
EN 558:2022 (E)
Introduction
The basic series given in this document are taken from the original series shown in Annex A. Changes
made to the original series will not be automatically incorporated into this document.
The numbers of the existing ISO basic series are maintained as in ISO 5752:2021.
4
BS EN 558:2022
EN 558:2022 (E)
1 Scope
This document specifies the “face-to-face” (FTF) and “centre-to-face” (CTF) dimensions for PN and Class
designated metal valves used in flanged pipe systems.
This document covers valves with the following PN, Class and DN values:
— PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400;
— Class 125; Class 150; Class 250; Class 300; Class 600; Class 900; Class 1 500; Class 2 500;
— DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200;
DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900;
DN 1 000; DN 1 050; DN 1 200; DN 1 400; DN 1 600; DN 1 800; DN 2 000.
For valves in other shell materials than metal the same FTF and CTF dimensions can be used.
For relationship between DN and NPS, see Annex B.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 736-1, Valves - Terminology - Part 1: Definition of types of valves
3.1
face-to-face dimension
FTF
distance between the two planes perpendicular to the valve axis located at the extremities of the body
end ports or as specified in the relevant valve product standard
5
BS EN 558:2022
EN 558:2022 (E)
3.2
centre-to-face dimension
CTF
distance between the plane located at the extremity of either body end port and perpendicular to its axis
and the axis of the other body end port
Key
a face-to-face (FTF)
b centre-to-face (CTF)
Type A Type B
Key
a face-to-face (FTF)
Figure 2 — Flanged valves PN and Class designated (flat and raised faces)
6
BS EN 558:2022
EN 558:2022 (E)
7
BS EN 558:2022
EN 558:2022 (E)
Large
or
small
male
face
Large
or
small
female
face
Large
or
small
tongue
Large
or
small
groove
Key
a for dimensions see Tables 5 to 31
b face-to-face (FTF)
c centre-to-face (CTF)
e height
NOTE For height e, see EN 1759 series.
8
BS EN 558:2022
EN 558:2022 (E)
The basic series of FTF and CTF dimensions shall be as given in Tables 5 to 31.
In those tables, there are several series which are non-preferred, but represent history and commercial
decisions made by manufacturers utilizing only one pattern for PN and Class designated valves. Those
series are identified in the relevant tables.
4.2 Face-to-face and centre-to-face dimensions
4.2.1 General
9
BS EN 558:2022
EN 558:2022 (E)
Table 1 — Correspondence between the FTF series tables of valve types and the product
standards
Product standard
Table numbers Designation
number
EN 1171 Industrial valves — Cast iron gate valves
5, 6 EN 1984 Industrial valves — Steel gate valves
EN 12288 Industrial valves — Copper alloy gate valves
Industrial valves — Metallic butterfly valves for
7, 8, 9, 10 EN 593
general purposes
11, 12 EN 1983 Industrial valves — Steel ball valves
Industrial valves — Diaphragm valves made of
13 EN 13397
metallic materials
EN 13789 Industrial valves — Cast iron globe valves
14, 15, 16, 17 Industrial valves — Steel globe and globe stop and
EN 13709
check valves
For Class designated valves with ring joint flanges, the FTF or CTF dimensions given in Tables 6, 8, 10, 12,
15, 17, 19, 21, 23, 25, 27, 29 shall be increased by x as defined in Table 2 and Figure 5.
10
BS EN 558:2022
EN 558:2022 (E)
a)
b)
Key
a FTF = Dimension of Tables 6, 8, 10, 12, 15, 19, 21, 23, 27, 29 + x
b CTF= Dimension of Tables 17, 25 + 0.5x
Figure 5 — FTF and CTF dimensions for Class designated valves with ring joint flanges
11
BS EN 558:2022
EN 558:2022 (E)
Nominal
Additional length x for ring joint flanges
size
DN Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500
15 11,1 11,1 −1,6
20 0
25 0 0
12,7 0
32
40 3,2
50
65
6,4
80 3,2
100 9,5
125 3,2
12,7 12,7
150 6,4
15,9 3,2
200 15,9
9,5
250
22,2
300 15,9
350 19,1
9,5
400
450 22,2
12,7
500 19,1 6,4
600 22,2 9,5 19,1 28,6
—
700
25,4 12,7
750
800 — — —
900 28,6 15,9
1 000
12
BS EN 558:2022
EN 558:2022 (E)
For valves having a resilient lining which forms the gasket joint with the mating flanges, the FTF and CTF
dimensions shall be the distance between the extremities of the valve in the installed condition. If the
dimensions for CTF and FTF differ from the standard dimensions, they shall be given by the manufacturer.
For valves having a hard lining, the thickness of the lining on the mating surface shall be included in the
FTF and CTF dimensions given in Tables 5 to 31, unless the design of the valve precludes such an
inclusion.
If this is the case, the manufacturer shall indicate the deviation from the standardized FTF or CTF
dimensions in his documentation.
4.2.4 Raised face flanges
The raised face dimensions shall be in accordance with the applicable flange standard.
4.3 Tolerances
Tolerances on FTF and CTF dimensions are given in Table 3. Both tolerances shall be fulfilled.
End flange seating surfaces shall be parallel or perpendicular. Tolerances “c” on the parallelism or
perpendicularity as shown in Figure 6 are given in Table 4.
13
BS EN 558:2022
EN 558:2022 (E)
DN Tolerances
10 to 25 0,4
32 to 150 0,6
200 to 300 0,8
350 to 500 1,0
600 to 800 2,0
1 000 and higher 3,0
14
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF series for the specified pressure designation
size
PN 6 — 10 — PN 6 — 10 — 16 — PN 25 — 40 — PN 160 — PN 250 —
16 25 — 40 63 — 100 250 320 — 400
DN
3a 14 15 26 99 91
10 102 115 — — — —
15 108 115 — — — —
20 117 120 — — — —
25 127 125 120 — — —
32 140 130 140 — — —
40 165 140 240 240 270 310
50 178 150 250 250 300 350
65 190 170 270 290 360 425
80 203 180 280 310 390 470
100 229 190 300 350 450 550
125 254 200 325 400 525 650
150 267 210 350 450 600 750
200 292 230 400 550 750 950
250 330 250 450 650 900 1 150
300 356 270 500 750 1 050 1 350
350 381 290 550 850 1 200 1 550
400 406 310 600 950 1 350 1 750
450 432 330 650 1 050 1 500 1 950
500 457 350 700 1 150 1 650 2 150
600 508 390 800 1 350 — —
700 610 430 900 1 550 — —
750 610 — — — — —
800 660 470 1 000 1 750 — —
900 711 510 1 100 1 950 — —
1 000 813 550 1 200 2 150 — —
1 050 — — — — — —
1 200 — 630 — — — —
15
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF series for the specified pressure designation
size
PN 6 — 10 — PN 6 — 10 — 16 — PN 25 — 40 — PN 160 — PN 250 —
16 25 — 40 63 — 100 250 320 — 400
DN
3a 14 15 26 99 91
1 400 — 710 — — — —
1 600 — 790 — — — —
1 800 — 870 — — — —
2 000 — 950 — — — —
a Non-preferred.
16
BS EN 558:2022
EN 558:2022 (E)
17
BS EN 558:2022
EN 558:2022 (E)
Table 7 — Butterfly valves and butterfly control valves — Flanged type — PN rating
Dimensions in millimetres
Nominal size Applicable FTF Series for the specified pressure designation
PN 2,5 — 6 — 10 — 16 — 25 — 40
DN
13 14
20 — 120
25 — 125
32 — 130
40 106 140
50 108 150
65 112 170
80 114 180
100 127 190
125 140 200
150 140 210
200 152 230
250 165 250
300 178 270
350 190 290
400 216 310
450 222 330
500 229 350
600 267 390
700 292 430
750 — —
800 318 470
900 330 510
1 000 410 550
1 050 — —
1 200 470 630
1 400 530 710
1 600 600 790
1 800 670 870
2 000 760 950
18
BS EN 558:2022
EN 558:2022 (E)
Table 8 — Butterfly valves and butterfly control valves — Flanged type — Class rating
Dimensions in millimetres
Nominal
Applicable FTF Series for the specified pressure designation
size
Class 125 — 150 Class 250 — 300 Class 600
DN
13 14 16 20 25 14 16 25 14
20 — 120 — 33 — 120 — — 120
25 — 125 — 33 — 125 — — 125
32 — 130 — 33 — 130 — — 130
40 106 140 33 33 — 140 33 — 140
50 108 150 43 43 — 150 43 — 150
65 112 170 46 46 — 170 46 — 170
80 114 180 64 46 49 180 64 49 180
100 127 190 64 52 56 190 64 56 190
125 140 200 70 56 64 200 70 64 200
150 140 210 76 56 70 210 76 70 210
200 152 230 89 60 71 230 89 71 230
250 165 250 114 68 76 250 114 76 250
300 178 270 114 78 83 270 114 83 270
350 190 290 127 78 92 92 290 127 92 290
400 216 310 140 102 102 310 140 102 310
450 222 330 152 114 114 330 152 114 330
500 229 350 152 127 127 350 152 127 350
600 267 390 178 154 154 390 178 154 390
700 292 430 229 165 — 430 229 — 430
750 — — 165 165 190 — — — — —
800 318 470 241 190 — 470 241 — 470
900 330 510 241 200 203 — 510 — — 510
1 000 410 550 300 251 216 — 550 — — 550
1 050 — — — — — — — — —
1 200 470 630 350 276 — — 630 — — 630
1 400 530 710 390 279 — 710 390 — 710
1 600 600 790 440 318 — 790 440 — 790
1 800 670 870 490 356 — 870 490 — 870
2 000 760 950 540 406 — 950 540 — 950
19
BS EN 558:2022
EN 558:2022 (E)
Table 9 — Butterfly valves and butterfly control valves — Wafer type — PN rating
Dimensions in millimetres
Nominal size Applicable FTF Series for the specified pressure designation
PN 2,5 — 6 PN 10 — 16 — 25 — 40
DN
20 a 25 16 20 25
20 33 — — 33 —
25 33 — — 33 —
32 33 — — 33 —
40 33 37 33 33 37
50 43 44 43 43 44
65 46 49 46 46 49
80 46 49 64 46 49
100 52 56 64 52 56
125 56 64 70 56 64
150 56 70 76 56 70
200 60 71 89 60 71
250 68 76 114 68 76
300 78 83 114 78 83
350 78 92 127 78 92
400 102 102 140 102 102
450 114 114 152 114 114
500 127 127 152 127 127
600 154 154 178 154 154
700 165 — 229 165 —
750 190 165 230 190 165
800 190 — 241 190 —
900 203 200 241 203 200
1 000 216 — 300 216 —
1 050 — 251 — — 251
1 200 254 276 350 254 276
1 400 279 — 390 279 —
1 600 318 — 440 318 —
1 800 356 — 490 356 —
2 000 406 — 540 406 —
a Non-preferred.
20
BS EN 558:2022
EN 558:2022 (E)
Table 10 — Butterfly valves and butterfly control valves — Wafer type — Class rating
Dimensions in millimetres
Nominal Applicable FTF Series for the specified pressure designation
size
21
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF Series for the specified pressure designation
size
PN 63 —
PN 6 — 10 — 16 PN 25 — 40
DN 100
1 12 26 27 1 4 12 26 27 28
10 130 130 — 115 130 — 130 — 115 130
15 130 130 — 115 130 140 130 — 115 130
20 150 130 — 120 150 152 130 — 120 150
25 160 140 — 125 160 165 140 — 125 160
32 180 165 — 130 180 178 165 — 130 180
40 200 165 240 140 200 190 165 240 140 200
50 230 203 250 150 230 216 203 250 150 230
65 290 222 290 170 290 241 222 290 170 290
80 310 241 310 180 310 283 241 310 180 310
100 350 305 350 190 350 305 305 350 190 350
125 400 356 400 325 400 381 356 400 325 400
150 480 394 450 350 480 403 394 450 350 450
200 600 457 550 400 600 419 457 550 400 550
250 730 533 650 450 730 457 533 650 450 650
300 850 610 750 500 850 502 610 750 500 750
350 980 686 850 550 980 762 686 850 550 850
400 1 100 762 950 762 1 100 838 762 950 762 950
450 1 200 864 1 050 — 1 200 914 864 1 050 — —
500 1 250 914 1 150 914 1 250 991 914 1 150 914 1 150
600 1 450 1 067 1 350 — 1 450 1 143 1 067 1 350 — —
700 1 650 — 1 550 — 1 650 1 346 — 1 550 — —
750 — — — — — 1 397 — — — —
800 1 850 — 1 750 — 1 850 1 524 — 1 750 — —
900 2 050 — 1 950 — 2 050 1 727 — 1 950 — —
1 000 2 250 — 2 150 — 2 250 — — 2 150 — —
22
BS EN 558:2022
EN 558:2022 (E)
Class 125 — 150 Class 250 — 300 Class 600 Class 900
DN
1 12 1 4 5 54
10 130 130 130 — — —
15 130 130 130 140 165 —
20 150 130 150 152 190 229
25 160 140 160 165 216 254
32 180 165 180 178 229 279
40 200 165 200 190 241 305
50 230 203 230 216 292 368
65 290 222 290 241 330 419
80 310 241 310 283 356 381
100 350 305 350 305 432 457
125 400 356 400 381 508 559
150 480 394 480 403 559 610
200 600 457 600 419 b 660 737
250 730 533 730 457 c 787 838
300 850 610 850 502 d 838 965
350 980 686 980 762 889 1 029
400 1 100 762 1 100 838 991 1 130
450 1 200 864 1 200 914 1 092 1 219
500 1 250 914 1 250 991 1 194 1 321
600 1 450 1 067 1 450 1 143 1 397 1 549
700 1 650 — 1 650 1 346 1 549 —
750 — — — 1 397 1 651 —
800 1 850 — 1 850 1 524 1 778 —
900 2 050 — 2 050 1 727 2 083 —
1 000 2 250 — 2 250 — — —
a All dimensions can be used for plug valves with the agreement of the purchaser.
b For full bore ball valves, use 502.
c For full bore ball valves, use 568.
d For full bore ball valves, use 648.
23
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 125 —
PN 10 — 16 —
PN 6 — 10 — 16 Class 125 — 150 150 — 250 —
DN 25 — 40
300
7 1 1 7
10 108 130 130 108
15 108 130 130 108
20 117 150 150 117
25 127 160 160 127
32 146 180 180 146
40 159 200 200 159
50 190 230 230 190
65 216 290 290 216
80 254 310 310 254
100 305 350 350 305
125 356 400 400 356
150 406 480 480 406
200 521 600 600 521
250 635 730 730 635
300 749 a 850 850 749 a
a Also used for DN 350, DN 400, DN 450 and DN 500.
24
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
PN 63 — 100 — PN 250 —
PN 6 — 10 — 16 PN 25 — 40
DN 160 320 — 400
1 14 125 1 125 2 92
10 130 115 — 130 — 210 230
15 130 115 — 130 — 210 230
20 150 120 — 150 — 230 260
25 160 125 — 160 — 230 260
32 180 130 — 180 — 260 300
40 200 140 — 200 — 260 300
50 230 150 — 230 — 300 350
65 290 170 — 290 — 340 400
80 310 180 — 310 — 380 450
100 350 190 300 350 300 430 520
125 400 200 325 400 325 500 600
150 480 210 350 480 350 550 700
200 600 230 400 600 400 650 800
250 730 250 450 730 450 775 900
300 850 270 500 850 500 900 1 050
350 980 290 550 980 550 1 025 —
400 1 100 310 600 1 100 600 1 150 —
450 1 200 330 650 1 200 650 1 275 —
500 1 250 350 750 1 250 750 1 400 —
600 1 450 390 900 1 450 900 1 600 —
700 1 650 430 1 050 1 650 1 050 — —
750 — — — — — — —
800 1 850 470 1 200 1 850 1 200 — —
900 2 050 510 1 350 2 050 1 350 — —
1 000 2 250 550 1 500 2 250 1 500 — —
1 050 — — — — — — —
1 200 — 630 1 800 — 1 800 — —
1 400 — 710 2 100 — 2 100 — —
1 600 — 790 2 500 — 2 500 — —
1 800 — 870 2 700 — 2 700 — —
2 000 — 950 3 000 — 3 000 — —
25
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF Series for the specified pressure designation
size
Class 250 —
Class 125 — 150 Class 600 Class 900 Class 1 500 Class 2 500
DN 300
1a 10 1 21 5 54 55 56
10 130 — 130 — — — — —
15 130 108 130 152 165 — 216 264
20 150 117 150 178 190 229 229 273
25 160 127 160 203 216 254 254 308
32 180 140 180 216 229 279 279 349
40 200 165 200 229 241 305 305 384
50 230 203 230 267 292 368 368 451
65 290 216 290 292 330 419 419 508
80 310 241 310 318 356 381 470 578
100 350 292 350 356 432 457 546 673
125 400 356 400 400 508 551 673 794
150 480 406 480 444 559 610 705 914
200 600 495 600 559 660 737 832 1 022
250 730 622 730 622 787 838 991 1 270
300 850 698 850 711 838 965 1 130 1 422
350 980 787 980 — 889 1 029 1 257 —
400 1 100 914 1 100 — 991 1 130 1 384 —
450 1 200 — 1 200 — 1 092 1 219 1 537 —
500 1 250 — 1 250 — 1 194 1 321 1 664 —
600 1 450 — 1 450 — 1 397 1 549 1 943 —
700 1 650 — 1 650 — 1 549 — — —
750 — — — — 1 651 — — —
800 1 850 — 1 850 — 1 651 — — —
900 2 050 — 2 050 — 2 083 — — —
1 000 2 250 — 2 250 — — — — —
a Non-preferred.
26
BS EN 558:2022
EN 558:2022 (E)
Table 16 — Globe valves and lift check valves — Angle pattern — PN rating
Dimensions in millimetres
Nominal
Applicable CTF Series for the specified pressure designation (EN 16767)
size
PN 63 — 100 — PN 250 — 320 —
PN 6 PN 10 — 16 — 25 — 40
DN 160 400
22 a 23 a 8 22 a 23 a 9 93
10 65 70 90 65 70 105 115
15 65 70 90 65 70 105 115
20 70 75 95 70 75 115 130
25 80 85 100 80 85 115 130
32 90 95 105 90 95 130 150
40 95 100 115 95 100 130 150
50 105 115 125 105 115 150 175
65 115 125 145 115 125 170 200
80 125 135 155 125 135 190 225
100 135 146 175 135 146 215 260
125 — — 200 — — 250 300
150 — — 225 — — 275 350
200 — — 275 — — 325 400
250 — — 325 — — 390 —
300 — — 375 — — 450 —
350 — — 425 — — 515 —
400 — — 475 — — 575 —
450 — — 500 — — — —
500 — — — — — 700 —
a This series applies to copper alloy valves only. It is not used for cast iron or steel valves.
27
BS EN 558:2022
EN 558:2022 (E)
Table 17 — Globe valves and lift check valves — Angle pattern — Class rating
Dimensions in millimetres
Nominal
Applicable CTF Series for the specified pressure designation (EN 16767)
size
Class Class Class
Class 125 — 150 Class 250 — 300 Class 600
DN 900 1 500 2 500
11 22 a 23 a 8b 23 a 32 9b 24 57 58 59
10 51 65 70 90 70 — 105 — — — —
15 57 65 70 90 70 76 105 83 — 108 132
20 64 70 75 95 75 89 115 95 114 114 137
25 70 80 85 100 85 102 115 108 127 127 154
32 76 90 95 105 95 108 130 114 140 140 175
40 83 95 100 115 100 114 130 151 152 152 193
50 102 105 115 125 115 133 150 146 184 184 225
65 108 115 125 145 125 146 170 165 210 210 254
80 121 125 135 155 135 159 190 178 190 235 289
100 146 135 146 175 146 178 215 216 229 273 337
125 178 — — 200 — 200 250 254 279 337 397
150 203 — — 225 — 222 275 279 305 352 457
200 248 — — 275 — 279 325 330 368 416 511
250 311 — — 325 — 311 390 394 419 495 635
300 349 — — 375 — 356 450 419 483 565 711
350 394 — — 425 — — 515 — 514 629 —
400 457 — — 475 — — 575 — 660 — —
450 483 — — 500 — — — — 737 — —
500 — — — — — — 700 — 825 — —
600 — — — — — — — — 991 — —
a This series applies to copper alloy valves only. It is not used for cast iron or steel valves.
b Non-preferred.
28
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF Series for the specified pressure designation
size
PN 6 — 10 — 16 — PN 250 —
PN 6 — 10 — 16 PN 63 — 100 PN 160
DN 25 — 40 400
14 48 1 7a 18 a 2 26 99 91
10 115 — 130 108 80 210 — — —
15 115 — 130 108 80 210 — — —
20 120 — 150 117 90 230 — — —
25 125 — 160 127 100 230 — — —
32 130 — 180 146 110 260 — — —
40 140 180 200 159 120 260 240 270 310
50 150 200 230 190 135 300 250 300 350
65 170 240 290 216 165 340 290 360 425
80 180 260 310 254 185 380 310 390 470
100 190 300 350 305 229 430 350 450 550
125 200 350 400 356 — 500 400 525 650
150 210 400 480 406 — 550 450 600 750
200 230 500 600 521 — 650 550 750 950
250 250 600 730 635 — 775 650 900 1 150
300 270 700 850 749 — 900 750 1 050 1 350
350 290 800 980 — — 1 025 850 1 200 1 550
400 310 900 1 100 — — 1 150 950 1 350 1 750
450 330 1 000 1 200 — — 1 275 1 050 1 500 1 950
500 350 1 100 1 250 — — 1 400 1 150 1 650 2 150
600 390 1 300 1 450 — — 1 600 1 350 — —
700 430 1 500 1 650 — — — 1 550 — —
750 — — — — — — — — —
800 470 1 700 1 850 — — — 1 750 — —
900 510 1 900 2 050 — — — 1 950 — —
1 000 550 2 100 2 250 — — — 2 150 — —
1 050 — — — — — — — — —
1 200 630 — — — — — — — —
1 400 710 — — — — — — — —
1 600 790 — — — — — — — —
1 800 870 — — — — — — — —
2 000 950 — — — — — — — —
NOTE For lift check valves, angle pattern, see Table 16.
a This series applies to copper alloy valves only. It is not used for cast iron or steel valves.
29
BS EN 558:2022
EN 558:2022 (E)
Table 19 — Flanged check valves — Straight and oblique pattern — Class rating
Dimensions in millimetres
Nominal
Applicable FTF Series for the specified pressure designation
size
Class 125 —
Class 150 — Class 125 —
150 — Class 250 — 300 Class 600 Class 900 Class 1 500 Class 2 500
DN 300 150
250 — 300
1a 7b 18 b 10 21 5 54 55 56
10 130 108 80 — — — — — —
15 130 108 80 108 — 165 — 216 264
20 150 117 90 117 — 190 229 229 273
25 160 127 100 127 216 216 254 254 308
32 180 146 110 140 229 229 279 279 349
40 200 159 120 165 241 241 305 305 384
50 230 190 135 203 267 292 368 368 451
65 290 216 165 216 292 330 419 419 508
80 310 254 185 241 318 356 381 470 578
100 350 305 229 292 356 432 457 546 673
125 400 356 — 330 400 508 551 673 794
150 480 406 — 356 444 559 610 705 914
200 600 521 — 495 533 660 737 832 1 022
250 730 635 — 622 622 787 838 991 1 270
300 850 749 — 698 711 838 965 1 130 1 422
350 980 — — 787 838 889 1 029 1 257 —
30
BS EN 558:2022
EN 558:2022 (E)
Nominal
Applicable FTF Series for the specified pressure designation
size
Class 125 —
Class 150 — Class 125 —
150 — Class 250 — 300 Class 600 Class 900 Class 1 500 Class 2 500
DN 300 150
250 — 300
1a 7b 18 b 10 21 5 54 55 56
400 1 100 — — 864 864 991 1 130 1 384 —
450 1 200 — — 978 978 1 092 1 219 1 537 —
500 1 250 — — 978 1 016 1 194 1 321 1 664 —
600 1 450 — — 1 295 1 346 1 397 1 549 1 943 —
700 1 650 — — 1 448 1 499 1 549 — — —
750 — — — 1 524 1 594 1 651 — — —
800 1 850 — — 1 676 — 1 651 — — —
900 2 050 — — 1 956 2 083 2 083 — — —
1 000 2 250 — — — — — — — —
NOTE For lift check valves, angle pattern, see Table 17.
a Non-preferred.
b This series applies to copper alloy valves only. It is not used for cast iron or steel valves.
31
BS EN 558:2022
EN 558:2022 (E)
32
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 125 Class 150 Class 250 — 300 Class 600 Class 900 Class 1 500 Class 2 500
DN
51 16 51 119 16 51 52 120 121 126 127 128
10 — — — — — — — — — — — —
15 — — — — — — 25 — — — — —
20 — — — — — — 31,5 — — — — —
25 — — — — — — 35,5 — — — — —
32 — — — — — — 40 — — — — —
40 — 33 — — 33 — 45 — — — — —
50 54 43 54 60 43 54 56 60 60 70 70 70
65 60 46 60 67 46 60 63 67 67 83 83 83
80 67 64 67 73 64 67 71 73 73 83 83 86
100 67 64 67 73 64 67 80 73 79 102 102 105
125 83 70 83 — 70 83 110 — — — — —
150 95 76 95 98 76 95 125 98 136 159 159 159
200 127 89 127 127 89 127 160 127 165 206 206 206
250 140 114 140 146 114 140 200 146 213 241 248 254
300 181 114 181 181 114 181 250 181 229 292 305 305
350 222 127 222 184 127 222 280 222 273 356 356 —
400 232 140 232 191 140 232 — 232 305 384 384 —
450 264 152 264 203 152 264 — 264 362 451 468 —
33
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 125 Class 150 Class 250 — 300 Class 600 Class 900 Class 1 500 Class 2 500
DN
51 16 51 119 16 51 52 120 121 126 127 128
500 292 152 292 219 152 292 — 292 368 451 533 —
600 318 178 318 222 178 318 — 318 438 495 559 —
700 381 229 381 305 229 381 — — — 572 — —
750 — — — 305 — — — 368 505 635 — —
800 489 241 489 — 241 489 — — — — — —
900 — 241 — 368 241 — — 483 635 718 — —
1 000 — 300 — — 300 — — — — 762 — —
1 050 — — — 432 — — — 568 701 787 — —
1 200 — 350 — 524 350 — — 629 — — — —
1 400 — 390 — — 390 — — — — — — —
1 600 — 440 — — 440 — — — — — — —
1 800 — 490 — — 490 — — — — — — —
2 000 — 540 — — 540 — — — — — — —
34
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
35
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
36
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500
DN
1 37 1 38 2 39 2 105 111 92 106 112 56 77
10 130 — 130 — 210 — 210 — — 230 — — — —
15 130 184 130 190 210 203 210 292 273 230 292 273 264 318
20 150 184 150 194 230 206 230 292 273 260 292 273 273 318
25 160 184 160 197 230 210 230 292 273 260 292 273 308 318
32 180 — 180 — 260 — 260 — — 300 — — 349 —
40 200 222 200 235 260 251 260 333 311 300 333 311 384 381
50 230 254 230 267 300 286 300 375 340 350 375 340 451 400
65 290 276 290 292 340 311 340 410 — 400 410 — 508 441
80 310 298 310 317 380 337 380 441 387 450 460 406 578 660
100 350 352 350 368 430 394 430 511 464 520 530 483 673 737
125 400 — 400 — 500 — 500 — — 600 — — 794 —
150 480 451 480 473 550 508 550 714 600 700 768 692 914 864
200 600 543 600 568 650 610 650 914 781 800 972 838 1 022 1 022
250 730 673 730 708 775 752 775 991 864 900 1 067 991 1 270 1 372
300 850 737 850 775 900 819 900 1 130 1 016 1 050 1 219 1 130 1 422 1 575
350 980 889 980 927 1 025 972 1 025 1 257 — — 1 257 — — 1 803
400 1 100 1 016 1 100 1 057 1 150 1 108 1 150 1 422 — — 1 422 — — —
450 1 200 — 1 200 — 1 275 — 1 275 1 727 — — 1 727 — — —
37
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500
DN
1 37 1 38 2 39 2 105 111 92 106 112 56 77
500 1 250 — 1 250 — 1 400 — 1 400 — — — — — — —
600 1 450 — 1 450 — 1 600 — 1 600 — — — — — — —
700 1 650 — 1 650 — — — — — — — — — — —
750 — — — — — — — — — — — — — —
800 1 850 — 1 850 — — — — — — — — — — —
900 2 050 — 2 050 — — — — — — — — — — —
1 000 2 250 — 2 250 — — — — — — — — — — —
38
BS EN 558:2022
EN 558:2022 (E)
39
BS EN 558:2022
EN 558:2022 (E)
40
BS EN 558:2022
EN 558:2022 (E)
Table 26 — Eccentric rotary plug control valves and segmented ball control valves — Wafer type
and flanged type — PN rating
Dimensions in millimetres
Nominal size Applicable FTF Series for the specified pressure designation
PN 10 — 16 — 25 — 40 PN 63 — 100
DN
1 36 1a 36
10 130 — 130 —
15 130 — 130 —
20 150 76 150 76
25 160 102 160 102
32 180 — 180 —
40 200 114 200 114
50 230 124 230 124
65 290 — 290 —
80 310 165 310 165
100 350 194 350 194
125 400 — 400 —
150 480 229 480 229
200 600 243 600 243
250 730 297 730 297
300 850 338 850 338
350 980 — 980 —
400 1 100 400 1 100 400
450 1 200 457 1 200 457
500 1 250 508 1 250 508
600 1 450 610 1 450 610
700 1 650 — 1 650 —
750 — — — —
800 1 850 — 1 850 —
900 2 050 — 2 050 —
1 000 2 250 — 2 250 —
a Only for eccentric rotary plug control valves.
41
BS EN 558:2022
EN 558:2022 (E)
Table 27 — Eccentric rotary plug control valves and segmented ball control valves — Wafer type
and flanged type — Class rating
Dimensions in millimetres
Nominal size Applicable FTF Series for the specified pressure designation
Class 150 — 300 — 600
DN
36
10 —
15 —
20 76
25 102
32 —
40 114
50 124
65 —
80 165
100 194
125 —
150 229
200 243
250 297
300 338
350 —
400 400
450 457
500 508
600 610
42
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
PN 10 — 16 PN 25 — 40 PN 63 — 100
DN
1 3 12 1 4 38 1 5 39
10 130 102 130 130 — — 130 — —
15 130 108 130 130 140 — 130 165 —
20 150 117 130 150 152 — 150 190 —
25 160 127 140 160 165 197 160 216 210
32 180 140 165 180 178 — 180 229 —
40 200 165 165 200 190 235 200 241 251
50 230 178 203 230 216 267 230 292 286
65 290 190 222 290 241 — 290 330 —
80 310 203 241 310 283 317 310 356 337
100 350 229 305 350 305 368 350 432 394
125 400 254 356 400 381 — 400 508 —
150 480 267 394 480 403 473 480 559 508
200 600 292 457 600 502 568 600 660 610
250 730 330 533 730 568 708 730 787 752
300 850 356 610 850 648 775 850 838 819
350 980 381 686 980 762 927 980 889 972
400 1 100 406 762 1 100 838 1 057 1 100 991 1 108
450 1 200 432 864 1 200 914 — 1 200 1 092 —
500 1 250 457 914 1 250 991 — 1 250 1 194 —
600 1 450 508 1 067 1 450 1 143 — 1 450 1 397 —
700 1 650 610 — 1 650 1 346 — 1 650 1 549 —
750 — 610 — — 1 397 — — 1 651 —
800 1 850 660 — 1 850 1 524 — 1 850 1 651 —
900 2 050 711 — 2 050 1 727 — 2 050 2 083 —
1 000 2 250 813 — 2 250 — — 2 250 — —
43
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
Class 150 Class 300 Class 600
DN
3 12 4 38 5 39
10 102 130 — — — —
15 108 130 140 — 165 —
20 117 130 152 — 190 —
25 127 140 165 197 216 210
32 140 165 178 — 229 —
40 165 165 190 235 241 251
50 178 203 216 267 292 286
65 190 222 241 — 330 —
80 203 241 283 317 356 337
100 229 305 305 368 432 394
125 254 356 381 — 508 —
150 267 394 403 473 559 508
200 292 457 502 568 660 610
250 330 533 568 708 787 752
300 356 610 648 775 838 819
350 381 686 762 927 889 972
400 406 762 838 1 057 991 1 108
450 432 864 914 — 1 092 —
500 457 914 991 — 1 194 —
600 508 1 067 1 143 — 1 397 —
700 610 — 1 346 — 1 549 —
750 610 — 1 397 — 1 651 —
800 660 — 1 524 — 1 651 —
900 711 — 1 727 — 2 083 —
1 000 813 — — — — —
44
BS EN 558:2022
EN 558:2022 (E)
Nominal size Applicable FTF Series for the specified pressure designation
PN 10 — 40 PN 63 — 100 PN 160 PN > 160
DN
113 2 114 122 123 124
10 — 210 — — — —
15 150 210 210 300 400 435
20 150 230 210 300 — —
25 160 230 230 300 415 470
32 230 260 320 — — —
40 230 260 320 420 — —
50 230 300 320 416 440 —
65 290 — — — — —
80 310 — — — — —
100 350 — — — — —
Nominal size Applicable FTF Series for the specified pressure designation
Class 150 — 300
DN
113
10 —
15 150
20 150
25 160
32 230
40 230
50 230
45
BS EN 558:2022
EN 558:2022 (E)
Annex A
(informative)
When the first edition of ISO 5752 was published in 1979 various series of face-to-face and centre-to-face
dimensions were adopted into ISO 5752 from the national standards that were current at that time. Each
series was given a basic series number and these numbers have been consistently used in subsequent
editions of ISO 5752. This policy of allocating basic series numbers to each dimension series was adopted
by CEN in EN 558:1995. As additional series have been added to both ISO 5752 and EN 558 these have
also been allocated basic series numbers.
This annex lists the basic series numbers for flanged valves that have been used in this document. It
includes series applicable to control valves and to steam traps, which are within the scope of this
document. It is intended to help the user of this document to understand the origins of the different series
and when they were introduced into and deleted from the different versions of this document.
Table A.1 — Origin of basic series
46
BS EN 558:2022
EN 558:2022 (E)
47
BS EN 558:2022
EN 558:2022 (E)
48
BS EN 558:2022
EN 558:2022 (E)
49
BS EN 558:2022
EN 558:2022 (E)
Annex B
(informative)
DN 10 15 20 25 32 40 50 65 80 100 125
NPS 3/8 1/2 3/4 1 11/4 11/2 2 21/2 3 4 5
DN 150 200 250 300 350 400 450 500 600 700
NPS 6 8 10 12 14 16 18 20 24 28
DN 750 a 800 900 1 000 1 050 a 1 200 1 400 1 500 1 600 1 800 2 000
NPS 30 32 36 40 42 48 56 60 64 72 80
a This DN is not included in EN ISO 6708.
50
BS EN 558:2022
EN 558:2022 (E)
Annex C
(informative)
The basic series listed in Table C.1 were included in EN 558:2017. They are no longer included in Tables 5 to 31 for the reason that their use is
considered special.
Table C.1 — Previously included basic series
Basic series
DN
29 30 33 43 45 46 47 50 53 69 70 71 82 94 98 100 101 107 108 115 116 117 118
10 108 — — — — — — — — — — — — — 65 35 55 — — — — — —
15 108 150 — 90 140 165 — — — — — — — — 65 35 55 50 — 290 480 — —
20 117,5 160 — 100 152 250 75 — — — — — — — 65 39 60 50 — 290 480 — —
25 127 160 — 115 210 255 80 — — 140 140 186 — 25 65 44 65 60 — 380 580 — —
32 127 180 — 130 230 265 90 — — 165 165 232 — 32 80 52 75 65 — 450 580 — —
40 136 190 152 150 240 280 100 — 38 178 178 232 — 40 85 64 85 80 — 490 680 — —
50 142 200 178 170 250 300 110 54 40 216 216 279 — 50 100 83 100 95 — 580 680 54 54
65 154 215 216 — 270 340 130 54 42 254 254 330 — 65 130 105 125 110 — — — 60 60
80 160 230 254 — 280 360 150 57 44 305 305 368 152 80 160 121 150 145 48 — — 67 67
100 172 250 305 — 300 400 160 64 46 356 406 457 178 100 190 152 185 170 54 — — 67 67
125 186 275 381 — 350 450 200 70 48 432 483 533 216 125 240 196 220 — — — — 83 83
150 200 300 457 — 375 500 210 76 50 508 559 610 254 150 250 236 280 — 57 — — 95 95
200 228 350 584 — 425 600 — 95 60 660 711 762 330 200 320 315 — — 64 — — 127 127
250 255 400 711 — 450 700 — 108 65 787 864 914 394 — — — — — 71 — — 140 140
300 285 425 813 — 500 800 — 143 75 914 991 1 041 457 — — — — — 81 — — 181 181
350 315 475 889 — 550 — — 184 80 991 1 067 1 118 495 — — — — — 92 — — 184 222
51
BS EN 558:2022
EN 558:2022 (E)
Basic series
DN
29 30 33 43 45 46 47 50 53 69 70 71 82 94 98 100 101 107 108 115 116 117 118
400 340 525 991 — 600 — — 191 95 1 092 1 194 1 245 — — — — — — 102 — — 191 232
450 360 575 1 092 — — — — 203 107 — 1 346 1 397 — — — — — — 114 — — 203 264
500 380 625 1 194 — — — — 213 120 — 1 473 — — — — — — — 127 — — 213 292
600 425 725 1 397 — — — — 222 144 — — — — — — — — — 154 — — 222 318
700 470 825 1 549 — — — — 321 160 — — — — — — — — — — — — — —
750 — — — — — — — — 180 — — — — — — — — — — — — 305 368
800 510 925 — — — — — 356 195 — — — — — — — — — — — — — —
900 555 1 025 — — — — — 368 210 — — — — — — — — — — — — 368 483
1 000 600 1 125 — — — — — 419 — — — — — — — — — — — — — — —
1 050 — — — — — — — — — — — — — — — — — — — — — 432 568
1 200 — — — — — — — — — — — — — — — — — — — — — 524 629
52
BS EN 558:2022
EN 558:2022 (E)
Bibliography
[1] EN ISO 6708, Pipework components - Definition and selection of DN (nominal size) (ISO 6708)
[2] EN 26554, Flanged automatic steam traps — Face-to-face dimensions (ISO 6554)
[3] EN 60534-3-2, Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions
for rotary control valves except butterfly valves
[4] ISO 5752:2021, Metal valves for use in flanged pipe systems — Face-to-face and centre-to-face
dimensions
[5] ANSI/ISA S75.15-1994, Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves
(ANSI Classes 150, 300, 600, 900, 1500 and 2500)
[6] ANSI/ISA-75.16-1993, Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies
(ANSI Classes 900, 1500 and 2500)
[7] ANSI/ISA-75.08.06-2002, Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies
(Classes 900, 1500, and 2500)
[8] API 594, Check Valves: Flanged, Lug, Wafer, and Butt-welding
[9] API 609, Butterfly Valves: Double Flanged, Lug- and Wafer-Type, and Butt-welding Ends
[15] NF E 29-305-2, Industrial valves — Valves used in flanged pipe systems — Part 2: Face to face
dimensions — FR series
[17] NF E 29-377, Industrial valves — Metallic wafer check valves with angular displacement obturator.
Specifications
53
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
Buying standards PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
You can buy and download PDF versions of BSI publications, including British and revised or replaced.
adopted European and international standards, through our website at bsigroup.
com/shop, where hard copies can also be purchased. To find out more about becoming a BSI Subscribing Member and the benefits
of membership, please visit bsigroup.com/shop.
If you need international and foreign standards from other Standards Development
Organizations, hard copies can be ordered from our Customer Services team. With a Multi-User Network Licence (MUNL) you are able to host standards
publications on your intranet. Licences can cover as few or as many users as you
Copyright in BSI publications wish. With updates supplied as soon as they’re available, you can be sure your
documentation is current. For further information, email cservices@bsigroup.com.
All the content in BSI publications, including British Standards, is the property
of and copyrighted by BSI or some person or entity that owns copyright in the Revisions
information used (such as the international standardization bodies) and has
formally licensed such information to BSI for commercial publication and use. Our British Standards and other publications are updated by amendment or revision.
Save for the provisions below, you may not transfer, share or disseminate any We continually improve the quality of our products and services to benefit your
portion of the standard to any other person. You may not adapt, distribute, business. If you find an inaccuracy or ambiguity within a British Standard or other
commercially exploit or publicly display the standard or any portion thereof in any BSI publication please inform the Knowledge Centre.
manner whatsoever without BSI’s prior written consent.
Useful Contacts
Storing and using standards Customer Services
Standards purchased in soft copy format: Tel: +44 345 086 9001
• A British Standard purchased in soft copy format is licensed to a sole named Email: cservices@bsigroup.com
user for personal or internal company use only.
Subscriptions
• The standard may be stored on more than one device provided that it is Tel: +44 345 086 9001
accessible by the sole named user only and that only one copy is accessed at Email: subscriptions@bsigroup.com
any one time.
• A single paper copy may be printed for personal or internal company use only. Knowledge Centre
Tel: +44 20 8996 7004
Standards purchased in hard copy format: Email: knowledgecentre@bsigroup.com
• A British Standard purchased in hard copy format is for personal or internal
company use only. Copyright & Licensing
Tel: +44 20 8996 7070
• It may not be further reproduced – in any format – to create an additional copy.
This includes scanning of the document. Email: copyright@bsigroup.com
If you need more than one copy of the document, or if you wish to share the BSI Group Headquarters
document on an internal network, you can save money by choosing a subscription
product (see ‘Subscriptions’). 389 Chiswick High Road London W4 4AL UK