Professional Documents
Culture Documents
User’s Manual
Regarding this manual
This manual explains how to install Windows PS Printer Driver and how to use it.
This PS Printer Driver can be used with Microsoft Windows Vista.
NOTE:
To use KM-4800w-PS Printer Driver, “UG-32” Option License is required.
1
Index
1. INSTALLATION METHOD................................................................................3
1.1. Install TCP/IP Port......................................................................................................................................................... 3
1.2. Add Printer...................................................................................................................................................................... 6
1.3. About Printer Port........................................................................................................................................................14
1.4. About reinstall of Printer..............................................................................................................................................17
2
1. Installation Method
NOTE:
If KM-4800wEN printer is already installed on your system, TCP/IP Port
installation has been completed at the same time.
Please go to [1.2 Add Printer] to continue the printer installation.
3. Click “OK”.
3
4. Click “Next”.
5. Click “Install”.
4
6. Please wait while the wizard is installing the components.
7. Click “Finish”.
5
1.2. Add Printer
2. Right-click within a blank region and select “Run as administrator” and “Add Printer”.
6
3. Click “Add a local printer”.
If "KM-4800w TCP/IP Port" exists, select "Use an existing port:" and specify the
"KM-4800w TCP/IP Port" from the pull-down menu.
7
5. Enter the KM-4800w’s IP address or host name.
Click “OK”.
8
7. Click “Browse”.
9
9. Click “OK”.
10
11. If KM-4800w PS Printer Driver is already installed on your system, the following
screen appears.
Select “Replace the current driver” and click “Next”.
11
13. Check “Always trust software from “KYOCERA MITA Corporation”.” and click “Install”.
12
15. Select “Do not share this printer” and click “Next”.
13
1.3. About Printer Port
Select the printer you have added by right-click, and select “Run as administrator” and
“Properties”.
14
Select the “Ports” Tab.
Select “KM-4800w:192.168….Port”, and click “Configure Port”.
15
The following information is indicated.
You do not have to change any of the above settings in usual case.
Change these settings when KM-4800w does not wake up correctly from the Power
Save Mode caused by the network settings.
16
1.4. About reinstall of Printer
When reinstalling KM-4800wEN-PS to the system, first delete the existing KM-
4800wEN-PS components.
Click “Yes”.
17
Right-click within a blank region and select “Run as administrator” and “Server
Properties”.
18
Select the “Drivers” Tab.
19
Select “Remove driver and driver package” and click “OK”.
Click “Yes”.
Click “Delete”.
20
Click “OK”.
If the removal of the driver is failed, reboot the PC, and then try to remove the driver
again.
Click “Close”.
21
2. Setting item of Printer Driver
If the setup conditions of the application is not correct, documents may not be printed
properly.
Select the printer you have installed by right clicking, and then open “Printing
Preferences”.
Each setting item in “Layout” Tab is explained on and after the next page.
22
< Orientation >
Orientation of paper can be selected.
“Rotated Landscape” rotates a “Landscape” image 180 degrees around.
<Page Order>
“Front to Back” outputs a multiple page file from the first page to the last page.
“Back to Front” outputs a multiple page file from the last page to the first page.
<Page Format>
Multiple images can be printed on 1 sheet of printing media.
16 images is the maximum number of images available to print on 1 sheet of printing
media.
“Draw Borders” surrounds all the images with borders.
<Tray Selection>
<Paper Source>
The source of paper can be selected.
“Automatically Select” is equivalent to “Auto”.
<Media>
The type of printing media can be selected.
23
Each setting item in “Advanced” is explained below.
<Paper/Output>
<Paper Size>
Specify the size of paper used for printing.
If “Custom Size” is selected in the above setting, the following dialog is
indicated.
A paper size can be specified at your option within the following range.
Width: 210 mm to 914.4 mm
Height: 297 mm to 10000 mm
24
<Copy Count>
Number of prints can be specified.
Available count ranges from 1 to 9999 but the guarantee range of proper
operation is from 1 to 999.
Checking “Collate” enables to print sets with collating.
<Graphic>
<Print Quality>
Printing resolution can be specified.
The printing resolution is normally set to 600dpi.
If there is any problem on a print, the printing resolution can be changed to
300dpi or 200 dpi.
<Scaling>
The printing image is enlarged or reduced according the specified value.
Available percentage ranges from 1 to 1000 but the guarantee range of proper
operation is from 20 to 500.
<Document Options>
25
<PostScript Options>
<Mirrored Output>
A mirror image can be printed when “Yes”.
<Negative Output>
A negative Image can be printed when “Yes”.
<Printer Features>
<Output Size>
The printing image is automatically enlarged or reduced just to fit the
paper size selected on “Output Size”.
26
PS Printer Driver for Windows Vista User’s Manual
27