Professional Documents
Culture Documents
Please make sure to check manual and installation video before using the product.
Products damaged or damaged by user usage, cannot be exchanged or refunded.
Please check the model and components before using the product.
• Match your device model with the product in advance.
• Please check all the components listed on the page3 and if there is any problem with the components,
please contact us before the installation.
2
Dome Premium Genuine Film Installation User Guide
Components
Reference
• There may be differences in components depending on the model.
• To improve the product, component's appearance or specifications etc. can be change without prior notice.
Jig Film
3
Dome Premium Genuine Film Installation User Guide
Installation
STEP1
Remove the protection film attached to your device using the Remover.
STEP2
Connect the Align block to top part of the JIG.
4
Dome Premium Genuine Film Installation User Guide
Installation
STEP3
Insert the device into the JIG in correct direction.
Top – Speaker
Bottom – Connector
STEP4
Clean the display with alcohol wipe and cleaning cloth.
Then, remove any dust with dust removal sticker.
Close the device to the stopper.
Installation
STEP5
Hold the top part of the film as shown, and bend the [1 sticker] as shown in [Figure 1].
Like [Figure 2] Make sure that the protective film and pet film are properly separated and
slowly remove the protective film. If it is as shown in [Figure 3], attach the protective film as if
it is in the first state and remove it carefully so that only the protective film can be removed.
• Please do not touch adhesion surface.
[Figure 2] POT
Film
m
fil
er
lin
1
POT
m
[Figure 1]
lm r fil
Fi
line
STEP6
Flip the film with the protective film removed so that the top/bottom text are visible to the front.
1) Insert the top part of the film into the Align block.
2) Insert the bottom part of the film into the bottom part of the JIG.
• Please do not touch adhesion surface.
• Make sure the film does not stick onto the device.
①
6
Dome Premium Genuine Film Installation User Guide
Installation
STEP7
Hold the top end of the film and slowly and forcefully push up with the squeegee from
the bottom of the jig to the top while maintaining squeegee in a lean angle.
Push the squeegee all the way to the end.
• Bubble might be appeared if you push the squeegee too fast.
<Directions of Use>
Slowly
Start
천천히 부착 하세요
7
Dome Premium Genuine Film Installation User Guide
Installation
STEP8
Remove the guide film from Jig's hole while pressing the ①-top/②-bottom of the film
with a squeegee. ③Push the film entirely to the short side of the squeeze.
<Directions of Use>
<Directions of Use>
8
Dome Premium Genuine Film Installation User Guide
Installation
STEP9
Bend the guide film attached to the film and remove it from the top.
Finish by pressing the film edge with the short part of the squeegee.
Remove the device from the JIG.
<Directions of Use>
9
Dome Premium Genuine Film Installation User Guide
STEP1
Use the alcohol wipe and the cleaning cloth to wipe down the device.
Remove any dust on your device with the dust remover sticker.
STEP2
Remove liner film(back).
Align the film starting with the top edges of the device.
10
Dome Premium Genuine Film Installation User Guide
STEP3
Tilt the protective film (1)180° and push with a squeegee to attach it.
Tilt the protective film (2)180° and push with a squeegee to attach it.
STEP4
Remove any bubbles with a squeeze.
With a dust removal sticker remove the front protective film.
* Please do not press the bubbles or lines after the installation, it will be naturally disappeared.
11
Dome Premium Genuine Film Installation User Guide
STEP1
Use the alcohol wipe and the cleaning cloth to wipe down the device.
Remove liner film[1].Place it on the device and attach it in position.
Tilt the protective film (2)180° and push with a squeegee to attach it.
Tilt the protective film (3)180° and push with a squeegee to attach it.
With a dust removal sticker remove the front protective film.
2 2
1
1
3 3
12
Dome Premium Genuine Film Installation User Guide
• Bubbles or lifting may occur by physical impacts such as drop impact, incompatible phone cases use,
excessive strength while cleaning with alcohol wipes or etc.
• No refund or exchange for any type of user damages.
※Global A/S※
CONTACT US
feedback@whitestonedome.com
HOMEPAGE
www.whitestonedome.com
> WARRANTY REQUEST
WHITESTONE Ltd.
13
The unique Component Manufacturer, Whitestone (www.whitestonedome.com) for Mobile Device.
Copyright ⓒ Whitestone Ltd. All rights reserved.