Professional Documents
Culture Documents
USER MANUAL
CONTENTS
Parameters……………………………………………………………………….2
Generator Location...........................................................................5
Power Connection............................................................................7
Water Feed.......................................................................................11
Steam Oulet.....................................................................................12
Drain Line.........................................................................................13
Auto Flush........................................................................................14
Express Steam..................................................................................16
isteam...............................................................................................17
isteam...............................................................................................18
I tempo.............................................................................................19
Remote Temperature Sensor.............................................................20
Remote Temperature Probe..............................................................22
Essential Oil Use................................................................................26
Shower Seat Installation………………………………………………………………….27
2
Models, parameters and dimension
Table 1
Heating
Power elements Voltage(V)/Curre dimension
Model KW (N*kW) nt (A) (L×W×H)(in)
ST-30 3 1*3.5 220/13.6 11.8*5.1*9.1
ST-40 4 1*4.0 220/18.2
220/20.5
ST-45 4.5 1*4.5 380/6.8 12.6*5.1*13.21
220/22.7
ST-50 5 1*5.0 380/9.1
220/27.3
15.6*5.9*15.6
ST-60 6 1*6.0 380/9.1
ST-70 7 1*7.0 220/31.8
ST-80 8 1*8.0 220/36.4 17.5*6.5*15.6
ST-90 9 1*9.0 380/13.6
ST-105 10.5 1*5=1*4.5 380/15.9
ST-120 12 2*6 380/18.2
ST-150 15 1*6+1*9 380/22.7
ST-180 18 2*9 380/27.3 19.7×7.9×20.5
table 2
Model time Range of Size(length*width*height)(mm)
(minute) temperature
ST-135 1~60 25℃~55℃ 100×100×40
ST-135M 1~60 25℃~55℃ 132×82×26
ST-135AD 1~60 25℃~55℃ 160×100×20
3
Locating the Stcmoet Generator
Select a location as near as practical to the steam room. Typical locations
include: closet, vanity cabinet, climate controlled attic or basement.
4
7. Install steam bath generator in an upright position only.
9. Provide a minimum of (12) inches at both ends and top of the steam
generator or as required for servicing.
5
Field Power Supply Connection
6
7
SELECTING THE PROPER STEAM GENERATOR:
Voltage Power line Fuse or
Model power Room size V/current A size breaker
kW ft3 mm2 A
ST-30 3 70~105 220/13.6 3×4 25
ST-40 4 105~140 220/18.2 3×4 25
ST-45 4.5 110~175 220/20.5 3×4 32
ST-45 4.5 110~175 380/6.8 5×2.5 16
ST-50 5 140~192 220/22.7 3×4 32
ST-50 5 140~192 380/9.1 5×2.5 16
ST-60 6 175~210 220/27.3 3×4 40
ST-60 6 175~210 380/9.1 5×2.5 16
ST-70 7 195~245 220/31.8 3×6 40
ST-80 8 245~315 220/36.4 3×6 60
ST-90 9 315~350 380/13.6 5×4 25
8
ST-105 10.5 315~420 380/15.9 5×4 25
ST-120 12 360~455 380/18.2 5×4 25
ST-150 15 420~560 380/22.7 5×4 32
ST-180 18 560~735 380/27.3 5×4 40
9
Water Feed
1. Connect cold water line.
2. Provide a shut off valve in the water supply line upstream
of the steam bath generator.
3. Do not overheat inlet solenoid valve with solder connec-
tions. Overheating will damage parts.
4. Flush inlet water line thoroughly before making connection to unit.
5. Strainer recommended upstream of feed water connection psig。
6. For best performance water pressure should be 15 to 20
PSIG. Reduce pressure as required if necessary required.
7. As required by local codes, install an approved backflow preventer.
8. Do not use PEX or PVC tubing Aluminum-plastic tube
10
Steam Outlet Pipe
Steam Outlet ( 1 ⁄ 2 ” NPT)
1. Do not install any valve in steam line. Flow of steam must
be unobstructed.
2. Use 1 ⁄ 2” brass pipe or copperorSUS304 tubing from unit to
steam head as permitted by codes.
3. Insulate steam line using pipe insulation rated 250˚ F or higher.
4. Pitch steam line 1 ⁄ 4 ” per foot towards steam head or steam
generator to avoid valleys and trapping of condensation.
NOTE: Running the steam line down and then up will create
a steam trap blocking the flow of steam.
11
Manual Drain Line
Drain ( 1 ⁄ 2 ” NPT)
NOTE: A drain valve is provided to facilitate servicing.
Provide a drain line connection from steam bath
generator drain valve according to national
and local codes. Check local plumbing code for
Unit drains by gravity.
Manual Drain Valve
(Shown in open position
Pitch as required for
Gravity Drain
12
Optional Auto Flush
Optional Auto Flush
13
Operation
The optional AutoFlush System feature automatically drains the
Stcmoet system following each use. A time delay allows the water
to cool down (about two hours) before it drains by gravity for a safe
and gentle operation.
NOTE: If the Express Steam option has been installed, the
AutoFlush will drain for ten minutes then refill with fresh water
to begin the pre-heat cycle
Installation Instructions
1. Plumbing to be performed by a qualified plumber and shall
be in accordance with applicable national and local codes. Unit
drains
by gravity. A drain line that is lower than the
Auto Flush assembly must be available. The Auto Flush System
valve outlet is 1 ⁄ 2 ” NPT. Check plumbing code for
receptor, trap and vent requirements.
2. Use copper or brass nipple 1 ⁄ 2 ” NPT x 3 1 ⁄ 2 ” or longer
(not supplied) to connect Auto Flush valve to the
Drain Valve. An arrow on the bottom of the Auto Flush
indicates the direction of flow.
CAUTION
PROVIDE DRAIN PLUMBING ACCORDING TO LOCAL
CODES. PLUMB AS REQUIRED FOR AUTOFLUSH SYSTEM.
14
Installing the I Steam Control
Controller selection
Installing the ST-135 or ST-135AD or ST-135M Control
Install the iSteam Control according to the installation and operation instructions
supplied with the Control. Failure to do so may result in an inoperative control
and a hazardous condition
ST-135 Controls
Refer to the Stcmoet
Installing the i Steam Control
1. Add a bead of silicone to the back of the I Steam housing. Plug the
I ST-135 into the audio pigtail on the back of the I Steam
control (6 pin mini-DIN). If an Audio Wizard is installed, the Audio
Wizard will plug into the I ST-135. (Diagram 2).
2. Carefully guide cables within the wall housing, then place I Steam
control into final position (Diagram 2
15
Diagram 1 Diagram 2 Diagram 3
CAUTION
Do not force or twist cable ends together.
Forcing or twisting cable ends may damage
the connectors
16
CAUTION
Do not force or twist cable ends together.
Forcing or twisting cable ends may damage
the connectors
17
CAUTION
Do not force or twist cable ends together.
Forcing or twisting cable ends may damage
the connectors
18
3. On/ Off key:light touching this key to start the equipment which
produces steam in a few minutes and then press this key to stop
the equipment. The working time set inside the equipment is 60
minutes and it will automatically shut down if over the time set;
4. Time / temperature setting key: After start-up, press the
temperature setting key to set the temperature and then press
the plus or minus key to adjust the temperature value. Then the
screen will display the set temperature value soon and press the
temperature setting key or waiting for 15 seconds to exit the
temperature setting status after the adjustment of the
temperature. The steam generator temperature shall be set in
the range between 25 ℃ ~ 55 ℃;
5. Number plus or minus key: increase and reduce the temperature.
19
Locating Controls Outside the Steam Room
by Using Remote Temperature Sensor
21
Connecting the Control Cable
to the Steam Generator
Route the control cable (provided with the control)
from the wall cutout to the steam generator.
steamhead
CAUTION: Use essential oils with caution. Essential oils are for
external use
only. Keep out of reach of children. Essential oils are highly
concentrated and
are potent substances and should not be applied directly to the
skin as they can
be irritants. Use essential oils with caution.
23
CAUTION: Place the drops into the Atcsteam AromaSteam
steamhead well
prior to turning on the steambath. Do not place drops in a hot
steam head as
SERIOUS INJURY CAN RESULT IF YOU DO NOT FOLLOW THIS
WARNING
CAUTION: Some people may find that the aroma makes them dizzy
and the user should exit the steam bath IMMEDIATELY. If skin
irritation
occurs, stop using the oils immediately. Remove any excess oil by
washing in mild soap and water. If ingested, rinse mouth with
water.
Administer water or milk to dilute. Contact a physician
immediately.
24
Teak wood seat drops for use and folds for storage.
Dimensions are: 19 5 ⁄ 8 ” w x 12 5 ⁄ 8 ” d x 1 1 ⁄ 4 ”
Hinge Pin
Caps
Seat Assembly
25
Completed Assembly
Shown in seating position
26
Thank you for choosing Atcsteam series steam generator with
well-designed structure, steady performance and convenient
installation. To form the whole set of steam bathing equipment,
you need a personal steam bathing room as well. The Stcmoet
steam generator is designed to remove tiredness, relax muscles an
stimulate circulation of the customers.
For proper installation, operation and maintenance, and the safety
of customer as well, please read all instructions carefully and keep
this manual for further reference.
27