Professional Documents
Culture Documents
( Reaffirmed 2004 )
Indian Standard
DTMENSIONS FOR PORCELAIN
TRANSFORMER BUSHINGS FOR USE IN
LIGHTLY POLLUTED ATMOSPHERES
PART 8 52 kV BUSHINGS
0 BIS 1992
FOREWORD
This Indian Standard ( Part S/Set 2 ) was adopted by the Bureau of Indian Standards, after the
draft finalized by the Electrical Insulators and Accessories Sectional Committee had been approved
by the Electrotechnical Division Council.
This standard ( Part 8/Set 2 ) covers the dimensions and materials of metal parts and accessories of
52 kV class transformer bushings with the object of ensuring their interchangeability.
The dimensions of porcelain transformer bushings of other voltage ratings are covered in IS 3347
‘Dimensions for porcelain transformer bushings for use in lightly polluted atmospheres’ and IS 8603
‘Dimensions for porcelain transformer bushings for use in heavily polluted atmospheres’ for use in
normal and lightly polluted atmospheres and heavily polluted atmospheres respectively.
The porcelain bushings for alternating voltage up to 1 000 V are covered in IS 7421 : 1988
‘Porcelain bushings for alternating voltage up to and including 1 000 V (first revision )‘.
This standard comprised two sections issued as two separate standards. While this section
( section 2 ) covers the dimensions of the metal parts and accessories, the porcelain parts are covered
in the other section ( Section 1 ).
For the purpose of deciding whether a particular requirement of this standard is complied with,
the final value, observed or calculated, expressing the result of a test, shall be rounded off in
accordance with IS 2 : 1960 ‘Rules for rounding off numerical values ( revised )‘. The number of
significant places retained in the rounded off value should be the same as that of the specified value
in this standard.
IS 3347 ( Part 8/Set 2 ) : 1992
hdian Standard
DIMENSIONS FOR PORCELAIN
TRANSFORMER BUSHINGS FOR USE IN
LIGHTLY POLLUTED ATMOSPHERES
PART 8 52 kV BUSHINGS
1 SCOPE 4 TOLERANCES
This standard ( Part 8/Set 2 ) lays down the 4.1 Unless specified otherwise, allowable toler-
dimensions, tolerances and materials of metal ances on dimensions of any machined part shall
parts and accessories of the bushings of 52 kV be in accordance with medium class of IS 2102
1000 A used with power transformers and (Part I): 1980.
reactors for use in lightly polluted atmospheres. 4.2 Unless specified otherwise, allowable toler-
ances of dimensions of any forged or cast metal
2 REFERENCE STANDARDS
part shall be in accordance with coarse class of
A list‘ of standards given in Annex A are IS 2102 (Part 1 ) : 1980.
necessary adjunct to this standard.
5 METAL PARTS AND ACCESSORIES
3 MATERIALS 5.1 Hexagonal Nuts
The materials of various parts shall conform to The dimensions of hexagonal nuts used shall
the relevant Indian Standards as specified below: conform to IS 1364 ( Part 3 ) : 1983. The threads
1
IS 3347 ( Part 8/Set 2) : 1992
M3Qx
M4Ekl .s
+----- 270 -1
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 ( Part 1 ) : 1980.
All dimensions in millimetres.
FIG. 1 STEM
0 100 y11>10
R7 - 1 i-----0 60’
RlO
5-
z’
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1) : 1980.
All dimensions in millimetres.
FIG. 2 CAP
2
IS 3347 ( Part 8/See 2) : 1992
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1 ) : 1980.
All dimensions in millimetres.
R2
d13
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1 ) : 1980.
All dimensions in millimetres.
3
IS 3347 (Part 8/Set 2) : 1992
HOLES
HARD PAPER
TUBE WOUND
OVER BRASS
TUBE
I - R2.5
------
-7-c
4
IS 3347 ( Part S/Set 2 ) : 1992
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1 ) : 1980.
All dimensions in millimetres.
6 THICK
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1 ) : 1980.
Ali dimensions in millimetres.
Thread ends and run out as per IS 1368 : 1980 and IS 1369 : 1982 respectively.
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1 ) : 1980.
All dimensions in millimetres.
---_
27 -W 155
Tolerance on dimensions without specific tolerances shall be coarse class of IS 2102 (Part 1) : 1980.
All dimensions in millimetres.
6
IS 3347 ( Part S/Set 2 ) : 1992
CLAMPING RING T
AS PER IS:L257(Part
DETAIL ‘A’
7
IS 3347 (Part 8/Set 2) : 1992
ANNEX A
( Clause 2.1 )
8
Standard Mark
The use of the Standard Mark is governed by the provrsrons of the Bureau of Indian
Standards Act, 1986 and the Rules and Regulations made thereunder. The Standard Mark on
products covered by an Indian Standard conveys the assurance that they have been produced
to comply with the requirements of that standard under a well defined system of inspection,
testing and quality control which is devised and supervised by BIS and operated by the
producer. Standard marked products are also continuously checked by BIS for conformity
to that standard as a further safeguard. Details of conditions under which a licence for the
use of the Standard Mark may be granted to manufacturers or producers may be obtained
from the Bureau of Indian Standards.
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Acf, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in
any form without the prior permission in writing of BIS. This does not preclude the free use, in the
course of implementing the standard, of necessary details, such as symbols and sizes, type or grade
designations. Enquiries relatin, 0 to copyright be addressed to the Director ( Publications ), BIS.
Indian Standards are reviewed periodically and revised, when necessary and amendments, if any, are
issued from time to time. Users of Indian Standards should ascertain that they are in possession of
the latest amendments or edition. Comments on this Indian Standard may be sent to BIS giving the
following reference :
Headquarters: