Professional Documents
Culture Documents
(Left-hand drive)
80 Ton Capacity
SPEC. SHEET NO. GR-800E-3-00503/EX-02
5,500:Mid1
6,700:Mid2
7,300:Max
2,700:Min
R4
,190
Min:12,000-Max:47,000
2,200
3,795
2°
12.
15.0°
445
2,502 1,875
3,315 3,550 3,780
8,020 3,950 2,405
14,375
GENERAL DIMENSIONS
Turning radius (29.5 - 25 Tires) Overall length approx. 14,375 mm
4 wheel steer 6.8 m Overall width approx. 3,315 mm
2 wheel steer 11.9 m Overall height approx. 3,795 mm
CRANE SPECIFICATIONS
CRANE SPECIFICATIONS
TADANO Automatic Moment Limiter • Main hydraulic oil pressure
(AML-C) including: • Fuel consumption monitor
• Control lever lockout function with audible and visual • Main winch / auxiliary winch select
pre-warning • Drum rotation indicator (audible and visible type) main and
• Number of parts of line auxiliary winch
• Boom position indicator • On-rubber indicator
• Outrigger state indicator
• Slewing angle TADANO AML-C monitors outrigger extended length and
• Boom angle / boom length / jib offset angle / jib length / load automatically programs the corresponding "RATED LIFTING
radius / rated lifting capacities / actual loads read out CAPACITIES" table
• Potential lifting height
• Ratio of actual load moment to rated load moment indication Operator's right hand console includes transmission gear selector,
• Automatic Speed Reduction and Slow Stop function on slewing lock lever and sight level bubble.
boom elevation and slewing Upper right console includes flood lamp switch, roof washer and
• Working condition register switch wiper switch, emergency outrigger set up key switch, jib status
• Load radius / boom angle / tip height / slewing range preset switch (option), eco mode switch and air conditioning control
function switch.
• External warning lamp
• Tare function NOTE: Each crane motion speed is based on unladen conditions.
CARRIER SPECIFICATIONS
TYPE AXLE
Rear engine, left-hand drive, driving axle 2-way selected type Front: Full floating type, steering and driving axle with planetary
by manual switch, 4x2 front drive, 4x4 front and rear drive. reduction.
Rear: Full floating type, steering and driving axle with planetary
FRAME reduction and non-spin rear differential.
High tensile steel, all welded mono-box construction.
STEERING
ENGINE Hydraulic power steering controlled by steering wheel.
Model MITSUBISHI 6M60-TLU3R 4 steering modes available: 2 wheel front, 2 wheel rear, 4 wheel
[ECE-R96-02] coordinated and 4 wheel crab.
Type Direct injection diesel
No. of cylinders 6 SUSPENSION
Combustion 4 cycle, turbo charged and after cooled Front: Rigid mounted to the frame.
Bore x Stroke, mm 118 x 115 Rear: Pivot mounted with hydraulic lockout device.
Displacement, liters 7.54
Air inlet heater 24 volt preheat BRAKE SYSTEMS
Air cleaner Dry type, replaceable element Service: Air over hydraulic disc brakes on all 4 wheels.
Oil filter Full flow with replaceable element Parking/Emergency: Spring applied-air released brake acting
Fuel filter Full flow with replaceable element on input shaft of front axle.
Fuel tank, liters 300, right side of carrier Auxiliary: Electro-pneumatic operated exhaust brake.
Cooling Liquid pressurized, recirculating by-pass
Radiator Fin and tube core, thermostat controlled TIRES - 29.5-25 34PR (OR) Air pressure: 400 kPa
Fan, mm Suction type, 6-blade, 600 dia.
Starting 24 volt OUTRIGGERS
Charging 24 volt system, negative ground 4 hydraulic, beam and jack outriggers.
Battery 2-120 amp. Hour Vertical jack cylinders equipped with integral holding valve.
Compressor, air, l /min 830 at 2,600 min-1 Each outrigger beam and jack is controlled independently from cab.
Output, Max. kW (HP) Gross 200 (267) at 2,600 min-1 Outrigger jack floats are attached thus eliminating the need of
Torque, Max. N•m 785 at 1,400 min-1 manually attaching and detaching them. Controls and sight level
Capacity, liters bubble located in superstructure cab. 4 outrigger extension lengths
Cooling water 13 are provided with corresponding "RATED LIFTING CAPACITIES"
Lubrication 13–15 for crane duty in confined areas.
Fuel 300 Min. Extension 2.7 m center to center
Mid. Extension 5.5 m center to center
TRANSMISSION Mid. Extension 6.7 m center to center
Electronically controlled full automatic transmission. Max. Extension 7.3 m center to center
Torque converter driving full powershift with driving axle selector. Float size (Diameter) 0.6 m
6 forward and 2 reverse speeds, constant mesh.
3 speeds - high range - 2-wheel drive; 4-wheel drive
3 speeds - low range - 4-wheel drive
-3 -
SPEC. SHEET NO. GR-800E-3-00503/EX-02
STANDARD EQUIPMENT
- Telematics (machine data logging and monitoring system) - Air dryer
with - HELLO-NET via internet - Water separator with filter (high filtration)
(availability depends on countries) - Air cleaner dust indicator
- Eco mode system - Full instrumentation package
- Positive control - Complete highway light package
- Over unwinding prevention - Tire inflation kit
- Emergency steering system - Towing hooks-Front and rear
- Transmission neutral position engine start - Lifting eyes
- Overshift prevention - Hook block tie down (front bumper)
- Parking braked travel warning - Weighted hook storage compartment
- Tilt-telescope steering wheel - Winch drum mirror
- Halogen head lamp - Tool storage compartment
- Fenders - Self-removable counterweight
OPTIONAL EQUIPMENT
- JIB (10.1 m or 17.7 m - 2 stage swing around boom extension) - Hook block–50 t capacity
- Preparation for JIB (storage and programming) (5 sheaves, swivel type with safety latch. Mass: approx. 500 kg)
- Wind speed indicator - Hook block–35 t capacity
- Hook block–80 t capacity (3 sheaves, swivel type with safety latch. Mass: approx. 450 kg)
(7 sheaves, swivel type with safety latch. Mass: approx. 700 kg) - Spark arrestor
- Hook block–60 t capacity
(6 sheaves, swivel type with safety latch. Mass: approx. 540 kg)
HOISTING PERFORMANCE
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
Main or auxiliary winch - 0.362 m drum Main and auxiliary drum grooved lagging
Line speeds1 Wire 19 mm wire rope
Line pulls Available2
Layer rope
m/min kN (kgf) Rope per layer Total wire rope
layer
Low High Low High m m
1st 84 118 89.1 (9,090) 63.9 (6,520) 1 34.2 34.2
2nd 92 128 80.7 (8,230) 57.8 (5,900) 2 37.3 71.5
3rd 99 139 73.7 (7,520) 52.8 (5,390) 3 40.3 111.8
4th 107 149 67.8 (6,920) 48.6 (4,960) 4 43.4 155.2
5th 115 160 62.8 (6,410) 45.1 (4,600) 5 46.4 201.6
6th 122 170 58.5 (5,970) 41.9 (4,280) 6 49.5 251.1
7th3 130 181 54.8 (5,590) 39.3 (4,010) 7 52.6 303.7
-4 -
SPEC. SHEET NO. GR-800E-3-00503/EX-02
360° ROTATION
3.5° 25° 45 70
°
65
60
47
.0-
m
Bo
om
+1 55
47 7.7
.0-
m -m
Bo Jib
80° om
+1 50
0.1
70° -m
Jib
60°
45
20 22°
.8
-m 20
16 Bo
.4 om 20°
-m
12 Bo 15
.0 om
-m
Bo
om 10° 10
5
0°
0
0 5 10 15 20 25 30 35 40 45 50
LOAD RADIUS (m)
Approx. Approx.
Approx.
2.5 m 2.3 m
2.3 m
NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook.
-5 -
SPEC. SHEET NO. GR-800E-3-00503/EX-02
SMART CHART
55
80° 50
70°
60° 45
47
.0
-m 40
42 Bo 50°
.6 om
-m
38 Bo 35
20 22°
.8
-m 20
Bo 20°
16 om
.4
-m
12 Bo 15
.0 om
-m
Bo
om 10°
10
5
0°
0
0 5 10 15 20 25 30 35 40 45 50
LOAD RADIUS (m)
Approx. Approx.
2.5 m 2.3 m
NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface.
Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook.
- 6-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
- 7-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
- 8-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
- 9-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
C: boom angle ( ˚)
R: Load radius (m)
W: Rated lifting capacity (Unit: ×1,000 kg)
-10-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
-11-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
-12-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
-13-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
-14-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
-15-
SPEC. SHEET NO. GR-800E-3-00503/EX-02
Tadano Ltd.
KANDA SQUARE 18th Floor, Phone : +81-3-6811-7309
2-2-1 Kanda-Nishikicho, URL www.tadano.com
Printed in Japan
Chiyoda-ku, Tokyo 101-0054, Japan E-mail info@tadano.com
2023-03-1