Professional Documents
Culture Documents
August 2014
00813-0100-4022, Rev JA
Leading edge capacitance sensor with integral temperature measurement for improved
total performance
4-20 mA HART® Smart capabilities and 0.25% of calibrated span reference accuracy
Rosemount 4600 August 2014
Leading edge capacitance sensor with integral 4-20 mA HART Smart capabilities
temperature measurement for improved total and 0.25% of calibrated span
performance reference accuracy
Integral temperature measurement means the Rosemount 4600 The HART protocol enables quick and easy reranging, calibration
provides superior temperature compensation and therefore, a and troubleshooting for nearly effortless field adjustments. As
more precise pressure measurement over the entire operating always, reference accuracy is specified as a percent of calibrated
temperature range. span, not as a percent of full scale, so you’re guaranteed 0.25%
reference accuracy whether you’re measuring 20,000 psi or 20
psi.
Contents
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 www.rosemount.com
August 2014 Rosemount 4600
Ordering Information
Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See
page 6 for more information on Material Selection.
Table 1. Rosemount 4600 Oil and Gas Pressure Transmitter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Pressure range
2 0-20 to 0-150 psi ★
4 0-125 to 0-5000 psi ★
5 0-330 to 0-10,000 psi
6 0-660 to 0-20,000 psi (available only with H11)
Isolating diaphragm/process connection materials
2 316L SST (1) ★
3 Alloy C-276 (1) ★
Output
A 4-20 mA with Digital Signal Based on HART protocol ★
Electrical connection
1 ★
5A /2-14 NPT Male with 72 in. Flying Lead
Software configuration
C1 Custom Software Configuration (CDS required with order) ★
Alarm limits
C6 Custom Alarm and Saturation Signal Levels, High Alarm ★
C7 Custom Alarm and Saturation Signal Levels, Low Alarm ★
Hardware adjustments
D1 Zero and Span Adjustments ★
www.rosemount.com 3
Rosemount 4600 August 2014
Table 1. Rosemount 4600 Oil and Gas Pressure Transmitter Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Product certifications
E1 ATEX Flameproof ★
E2 INMETRO Flameproof ★
I1 ATEX Intrinsic Safety ★
I2 INMETRO Intrinsic Safety ★
K1 ATEX Flameproof, Intrinsic Safety, Type n (combination of E1, I1, and N1) ★
N1 ATEX Type n ★
ND ATEX Dust Ignition-Proof ★
E5 FM Approval Explosionproof ★
I5 FM Approval Intrinsic Safety, Non-incendive ★
K5 FM Approval Explosionproof, Intrinsic Safety, Non-incendive (combination of E5 and I5) ★
E6 CSA Explosionproof, Division 2 ★
I6 CSA Intrinsic Safety ★
K6 CSA Explosionproof, Intrinsic Safety, Division 2 (combination of E6 and I6) ★
KA ATEX/ CSA Flameproof and Intrinsic Safety (combination of E1, I1, E6, and I6) ★
KB FM Approval and CSA Explosionproof and Intrinsic Safety (combination of E5, E6, I5, and I6) ★
KC FM Approval and ATEX Explosionproof and Intrinsic Safety (combination of E5, E1, I5, and I1) ★
Calibration certifications
Q4 Calibration Data Certificate consistent with ISO 104742.1 or EN 10204 2.1 ★
Transient protection
T1 Transient Protection ★
(1) Materials of Construction comply with recommendations per NACE MR0175/ISO 15156 for sour oilfield production environments. Environmental limits apply to
certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
4 www.rosemount.com
August 2014 Rosemount 4600
Specifications
Performance specifications Vibration effect
Less than ±0.1% of URL when tested per the requirements of
For zero-based spans, reference conditions, silicone oil fill, SST
IEC 60770.84 pipeline (general and extreme vibration level)
materials, 1/2 in.- 14 NPT process connections, digital trim values
(10-60 Hz 0.21mm peak to peak displacement/60-2000 Hz 3g).
set to equal range points. Does not include any error due to the
effects of sealed gauge. Electromagnetic Compatibility (EMC)
Meets all relevant requirements of EN 61326
Conformance to specification (±3 Sigma)
Technology leadership, advanced manufacturing techniques Transient protection (Option T1)
and statistical process control ensure specification conformance Meets IEEE C62.41, Category B
to at least ±3 sigma. 6 kV crest (0.5 μs - 100 kHz)
3 kA crest (8 × 20 microseconds)
Reference accuracy
6 kV crest (1.2 × 50 microseconds)
Includes the effects of terminal based linearity, hysteresis, and
Meets IEEE C37.90.1, Surge Withstand Capability
repeatability.
SWC 2.5 kV crest, 1.25 MHz wave form
Range 2: ±0.25% of calibrated span from 1:1 to 7.5:1 rangedown General Specifications:
Range 4: ±0.25% of calibrated span from 1:1 to 40:1 rangedown Response Time: < 1 nanosecond
Range 5: ±0.25% of calibrated span from 1:1 to 30:1 rangedown Peak Surge Current: 5000 amps to housing
Range 6: ±0.25% of calibrated span from 1:1 to 30:1 rangedown Peak Transient Voltage: 100 V dc
Loop Impedance: < 25 ohms
Long term stability Applicable Standards: IEC61000-4-4, IEC61000-4-5
0.5% of span for 3 years under normal operating conditions
Note
Calibrations at 68 °F (20 °C) per ASME Z210.1 (ANSI)
(1) 220°F (104°C) limit in vacuum service; 130°F (54°C) for pressures below 0.5 psia.
www.rosemount.com 5
Rosemount 4600 August 2014
Max. Loop Resistance = 43.5 (Power Supply Voltage – 11.25) Physical specifications
1355
Material selection
Load (Ohms)
Process temperature limits(1)(2) (2) Process temperature cannot exceed 220°F (104°C) in vacuum service.
–40 to 250 °F (–40 to 121°C) (3) Low alarm must be 0.1 mA less than low saturation and high alarm
must be 0.1 mA greater than high saturation.
6 www.rosemount.com
August 2014 Rosemount 4600
Process connections
• 1/2-14 NPT female (Available on Ranges 2 and 4 only)
• 1/4–18 NPT female (Not available on Range 6)
• Autoclave type F-250-C (Pressure relieved 9/16-18 gland thread: 1/4
OD high pressure tube 60° cone:
available Range 5 and 6 transmitters only.
Process sealing
Reliable dual process seal design meets the requirements NEC©
2002 section 501.5 (F)(3), 505.16 (E)(3) and API 14F/14FZ
6.8.2.2. No additional process sealing is required.
Process-wetted parts
Process isolating diaphragms
316L SST (1)
Alloy C-276 (3)
Non-wetted parts
Electronics housing
316L SST
NEMA 4X
IP 68, IP 66
Sensor module fill fluid
Silicone
www.rosemount.com 7
Rosemount 4600 August 2014
Product Certifications
European Directive Information E6 Explosionproof and Division 2
Certificate: 1384913
A copy of the EC Declaration of Conformity can be found at the
Standards: CSA Std C22.2 No. 25-1966; CSA Std C22.2 No.
end of the Quick Start Guide. The most recent revision of the EC
30-M1986; CAN/CSA-C22.2 No. 94-M91; CSA Std C22.2
Declaration of Conformity can be found at
No. 142-M1987; CAN/CSA-C22.2 No. 157-92; CSA Std
www.rosemount.com.
C22.2 No. 213-M1987; CAN/CSA-E79- 0-95; CAN/CSA-
Ordinary Location Certification E79-1-95; CAN/CSA- E79-11-95; ANSI/ISA No.
As standard, the transmitter has been examined and tested to 12.27.01-2011
determine that the design meets the basic electrical, Markings: Explosionproof for Class I, Division 1, Groups B,
mechanical, and fire protection requirements by a nationally C, and D; Dust-Ignitionproof for Class II and Class III,
recognized test laboratory (NRTL) as accredited by the Federal Division 1, Groups E, F, and G; Temperature Code T5 (-50
Occupational Safety and Health Administration (OSHA). °C to 40 °C); Explosion-proof for Class 1, Zone 1 Ex d IIC T5
(-20 °C to 40 °C); Suitable for Class I, Division 2, Groups A,
North America
B, C, and D when installed per Rosemount drawing
E5 Explosionproof and Dust-Ignitionproof 04620-5005; Enclosure Type 4X; Conduit seal not required
Certificate: 3012302 I6 Canada Intrinsically Safe
Standards:Class 3600; Class 3610; Class 3611; Class 3615; Certificate: 1384913
Class 3810; NEMA 250; ANSI/ISA-512.0.01; Standards: CSA Std C22.2 No. 25-1966; CSA Std C22.2 No.
ANSI/ISA-512.22.01; ANSI/ISA-60079-0; 30-M1986; CAN/CSA-C22.2 No. 94-M91; CSA Std C22.2
ANSI/ISA-60079-11 No. 142-M1987; CAN/CSA-C22.2 No. 157-92; CSA Std
Markings: Explosionproof for Class I, Division 1, Groups B, C22.2 No. 213-M1987; CAN/CSA-E79- 0-95; CAN/CSA-
C, and D; Explosion-Proof for Class 1, Zone 1 AEx d IIC T5 E79-1-95; CAN/CSA- E79-11-95; ANSI/ISA No.
(-40 °C to 85 °C); Dust-ignition proof for Class II and Class 12.27.01-2011
III, Division 1, Groups E, F, and G; Temperature Code T5 Markings: Intrinsically Safe for use in Class I, Division 1,
(Tamb = -40 °C to 85 °C); Enclosure Type 4X; Conduit seal Groups A, B, C, and D; Temperature Code T4 (-50 °C to 70
not required. °C); Intrinsically Safe for use in Class I, Zone 0 Ex ia IIC T4
I5 Intrinsically Safe and Nonincendive (-50 °C to 70 °C) when connected in accordance with
Certificate: 3012302 Rosemount drawing 04620-5007;
Standards: Class 3600; Class 3610; Class 3611; Class 3615; Enclosure Type 4X; For entity parameters see control
Class 3810; NEMA 250; ANSI/ISA-512.0.01; drawing 04620-5005
ANSI/ISA-512.22.01; ANSI/ISA-60079-0; Europe
ANSI/ISA-60079-11
Markings: Intrinsically Safe for use in Class I, Division 1, E1 ATEX Flameproof
Groups A, B, C, and D; Temperature Code T4 (-50 °C to 70 Certificate: KEMA02ATEX2231X
°C); Intrinsically Safe for use in Class I, Zone 0 AEx ia IIC T4 Standards: EN60079-0; EN60079-1; EN60079-26;
(-50 °C to 70 °C) in accordance with control drawing EN60079-31
04620-5007; Non-incendive for Class I, Division 2, Groups Markings: II 1/2 G Ex d IIC T6…T4 Ga/Gb
A, B, C, and D when connected in accordance with II 2 D Ex tb IIIC T135°C Db
Rosemount drawing 04620-5007; Enclosure Type 4X;
Temperature class/
maximum surface Ambient temp (°C) Process temp (°C)
temperature
8 www.rosemount.com
August 2014 Rosemount 4600
N1 ATEX Type n
Certificate No. Baseefa03ATEX0115X
Standards: EN60079-0, EN60079-15
Markings: II 3 G; Ex nA IIC T5 Gc (-40 °C ≤ Ta ≤ +70 °C)
Ui = 42.4V
Brazil
www.rosemount.com 9
Rosemount 4600 August 2014
Dimensional Drawings
Figure 1. Dimensional Drawings for the Rosemount 4600 Oil & Gas Panel Pressure Transmitter
A
A
7.1
(180.3)
6.6
(167.6)
E
C
1.5 1.5
(38.1) (38.1)
A. Ground D. Process Connection
B. Electrical Connection ½–14 NPT E. Optional Ground Screw (Standard with T1 Option)
C. Optional Ground Screw (Ordering Option D4)
10 www.rosemount.com
August 2014 Rosemount 4600
Figure 2. Dimensional Drawings for the Rosemount 4600 Oil & Gas Panel Pressure Transmitter
A A
B B
7.17
6.7 (182.1)
(169.5)
C E
D D
1.87 1.87
(47.6) (47.6)
A. Ground D. Process Connection
B. Electrical Connection ½–14 NPT E. Optional Ground Screw (Standard with T1 Option)
C, Optional Ground Screw (Ordering Option D4)
www.rosemount.com 11
Rosemount 4600 Product Data Sheet
00813-0100-4022 Rev JA August 2014