Professional Documents
Culture Documents
Office Interior - LX International - Opinion Cost To PANJETANI
Office Interior - LX International - Opinion Cost To PANJETANI
NOTE:
1 GST - will be extra as applicable.
2 Water & Power for construction & temporary lighting will be provided by Client free of cost at floor level.
3 Contractor will be paid actual quantity installed at site.
4 All guidelines should be follow as per DLF buildings norms and standard.
BILL OF QUANTITY & SPECIFICATION FOR OFFICE INTERIORS WORKS
LX INTERNATIONAL, GURUGRAM
06.03.2024
SL. No. DESCRIPTION UNIT MATERIAL LABOUR TOTAL TOTAL
A DEMOLITION & SITE PREPARATION WORK Rs. 0 0 0 0
F DOORS Rs. 0 0 0 0
H FINISHES Rs. 0 0 0 0
A.02 SITE PREPARATION :General housekeeping of site including regular removal of debris and waste material and Lumsum 1.00
keeping the site clean and workmanlike. The contractor to dispose off the materials, fittings and fixtures removed
from the site. PPE, regular sanitisation , safety posters for site awareness, identity cards and uniforms for all
supervisors, labourers, etc: to be included in the cost for the duration of the project.
B.02 BARE SLAB GRINDING AND PUTTY/ PUNNING: Bare slab (ceiling) treatment with hacking and chipping at the Sqm 132.00
edges or necessay places where undulations are clearly visible. Cost inclusive of surface finishing with
plastering/putty upto 2-3mm , labours, machine, material, scaffolding etc. as per site specific requirement and
instruction of project engineer. Work complete in all respect to the satisfaction of architect.
B.03 FLOOR CHIPPING, GRINDING & REPAIRING : Preparing the surface levelling by doing chipping , grinding & repair Sqm 132.00
manually or mechanically as per site reqiurements or directed by Engineer Incharge.
B.04 PCC SCREEDING (100 -150MM THICKNESS) : Provide and laying of 100-150mm thick cement screeding 1:2:4 (1 Sqm 132.00
Cement: 2 coarse sand :4 graded stone aggregate) and eventually the entire surface is to be TRUE HORIZONTAL
as measured through a water-level so as to attain an evenness/ horizontal surface to an extent of +- 5-7 mm
(minimum-to-maximum) to provide a finished horizontal surface, ready to receive floor finishes, tiles, carpets etc.
The finished floor of Lift Lobby to taken as the reference +/- 0.0 Level .
B.05 SELF-LEVELLING (Upto 3mm thick): Providing and application of Self-smoothening Cementitious Underlay upto Sqm 132.00
3mm thickness with primer after completion of surface preparation, repairing of Pot hole/crack/joint filling etc
with repair mortar, and complete as per manufacturer's guidelines.
C.02 CARPET TILE FLOORING : Providing and Installing of 500x500mm Carpet Tile as per approved shade including of Sqm 60.00
cutting, edge bending, pasting as per site requirements.
Specfication : Nylon backing, 20 Oz, tuffed loop pile.
Location : MD room, cabin area, meeting room.
C.03 TRANSITION STRIP : Providing and Installing of 25mm Thk Aluminium transition strip between different flooring Rmt 5.00
materials at the edge as per directed by Engineer Incharge
C.04 ALUMINUM SKIRTING : Providing and Fixing of 75mm THK Aluminium Skirting as per approved including of Rmt 90.00
cutting, pasting , screw as per directed by Engineer Incharge.
Sub-Total (FLOORING FINISHES) Same
D.01.01 (W)80mm x (H)18mm - Aluminium Profile - 2 hrs FIRE RATED GLASS to be used, with Aluminum profile as per sqm 7.00
design.
Location : Reception entrance
D.02 FRAMED GLASS PARTITION : Providing & fixing of single glazed partitions, fully relocatable & demountable single sqm 25.00
glazed partitions using single layer of 12mm thick clear toughened glass .The basic ceiling, floor , wall and
intermediary starter tracks to be made out of finished aluminum pre-equipped with non-glued acoustic seal of
minimum 3mm thickness. . The glass to be held within the track incorporating a glass seal within and placed on
internal glass levelers. Butt to Butt silicon for Glass to Glass joint, profile for the Edge glass joints and custom
profile for perpendicular glass. Rate not to include the door frames. Rate should include the floor chipping if
required and glass panels to be of maximum sizes and should be executed as per the detailed drawing and as per
architect's approval.
Location : MD Room & Cabin area
D.03 100MM THICK GYPSUM PARTITION : Providing and Fixing of Gypsum Partition Wall by using 12.5mm THK Double sqm 90.00
layer gypsum board of approved make including Putty at board joints and wherever necessary in the board,
sanding and masking tape etc all as per directed by Engineer Incharge.
Cost inclusive of Providing and placing 50 mm thick mineral wool insulation of 32 - 48 kg/ cum with 100 micron
polyvinyl sheet cover with both side of glass wool framing
D.04 75MM THICK GYPSUM PARTITION : Providing and Fixing of Gypsum Partition Wall by using 12.5mm THK single sqm 20.00
layer gypsum board of approved make including Putty at board joints and wherever necessary in the board,
sanding and masking tape etc all as per directed by Engineer Incharge.
Cost inclusive of Providing and placing 50 mm thick mineral wool insulation of 32 - 48 kg/ cum with 100 micron
polyvinyl sheet cover with both side of glass wool framing
D.05 75MM THICK LAMINATE/FILM FINISHED PARTITION : Providing and Fixing of 75mm X 50mm wooden sqm 10.00
batten/louvers and finished with 1mm thick laminate/Film over all visible faciaof approved shade and design as
per architect.
Installation Method : To be fixed using floor channel & tie rod from ceiling as per detail design.
D.10 CURTAIN BOX : Providing & fixing of Curtain Box 400L X 200H X 160L in "Z" Shape for vertical blinds in 19mm Rm 25.00
commercial ply and vertical side finished wth 12mm gypsum board as per site requirements.
Location : External glazing
E.02 PERFORATED ACOUSTIC CEILING ( HIGH QUALITY GYPSUM 0.9 NRC): Supply and installation of 12.5mm thick Sqm 20.00
perforated (Square/ Circular perforation as per design) acoustic board ceiling (Fire Class A2-s1,d0). The ceiling to
be monolithic finish and perforation patten as per detail design.
Desired emulsion paint cost to be charged separately elsewhere.
Note- Measurement will be on wall basis (No deduction in light fixtures , Grill/Diffusers and Column)
Make- USG/Knauf danoline
Location- Conference room
E.03 ARMSTRONG GRID CEILING : (1200L x 300D x 15T) : Providing and Installing of Grid Ceiling / False ceiling of Sqm 77.00
Make Armstrong (600mm x 1200mm including of standard G.I. Sections, hangers, edge members, other clips,
drops and cut-outs for light fixtures, Exhaust & AC grilles etc. as per site requirements.
Location : Workstation area
E.04 GYPSUM CEILING : Providing and fixing of single layer normal Gypsum False Ceiling and fixed with standard G.I. Sqm 8.00
Sections and 12mm thick Gyp Board, The rate includes required cutouts, as per design/details.
Location : Utility area
E.05 ACCESS PANEL/TRAP DOOR : Providing in position metal Access Panel / Trap Door from KNAUF DANOLINE No's 4.00
manufactured from 12mm plaster board (MR), outer and inner aluminum frame of 1.5 mm thickness Plus 0.2mm
thick powder coating, corner fittings of outer and inner frame made of hot dipped galvanized steel plate of
Thickness 2.0mm with zinc coating of 200g, Screw (Self-drilling Black Phosphate) mild steel C1018-1022, Sealing
Strip, of width 9.0mm and thickness 4.0mm, Snap Lock (Spring Catch / Catch Lock) of plastic ABS, Cold rolled steel
Q235 with Hinge thickness of 4.0mm and length:82mm, finished with white powder coat etch primer, having
beaded frame and budget lock operated by an square open drive. Knauf Danoline ebmossed at the back of the
frame. .
Size- 450x450 mm or as per site requirement.
E.06 RECESSED PELMETS FOR PROJECTOR : Fabricate and install pelmet in 12mm ply of width 250 mm and height 250 Rm 4.00
mm length 3000 mm cut into gypsum false ceilings and ready to receive projection screen. The cost to include the
support for the pelmet from the true slab.
E.07 GYPSUM COVE : Providing & fixing of Gypsum cove of size 100mmX75mm or as per drawing & site conditions Rm 55.00
with plain gypsum board 12.5mm thk & 9mm thick MDF including jointing with jointing tape & filler compound
finished with primer & emulsion paint of approved color & shade. All complete as per drawing & direction of
site-in-charge.
F DOORS
F.01 FIRE RATED STEEL DOOR : Supply & Installation of Fire Rated Steel Door of 2 Hrs Fire Rated including handle, lock No's 1.00
set, 2hrs FR toughend glass, intumescent fire seal strip & push to release handle inside as per approved drawing
& design or directed by client.
Door Size : 1000 x 2400mm
Hard ware : Dorma
Location : Main Entry
F.02 FRAMELESS GLASS DOOR: Supply and installation of 10mm thick toughened glass door with patch fitting and all No's 3.00
necessary hardware i.e. SS handle, lock, floor spring door stoper etc. Cost includes all necessary cut-out, holes,
transportation etc.
Handle shall be 1800mm high stainless steel Brush Finish.
Door size - 1000 x 2400mm
F.03 SINGLE LEAF LAMINATED FLUSH DOOR WITH VISION PANEL( 1000 X 2400):
Providing and fixing single leaf 40mm thk solid core 1mm laminated flush door with vision panel, hungs on side
hinges as per specification described below:
Door frame: door frame in Beech wood of size 100x75
Door Shutter: 38mm thick flush door finished both side with approved laminate. pattern as per detail
drawing/reference image.
Handle and lock: Mortise lock with 55mm backset and lever handle with Roses provided with one side key and
one side thumb turn in stainless steel from Dorma or equivalnet.
Hinges:Ozone or Equivalent, 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm, in SS 304 and in SSS finish.
Suitable for door weights upto 120kgs.
Door Closer:Ozone door closer
Door Stopper: Floor stop half dome with 45mm dia with fixing accessories, in satin Chrome
F.03.01 i) Sliding type with with vision panel, complete with sliding track, roller system and necessary hardware - Single No's 1.00
leaf (Size: 900x2400)
Location: Utility Room
F.03.02 ii) Sliding type with with vision panel, complete with sliding track, roller system and necessary hardware - Single No's 1.00
leaf (Size: 1200x2400)
Location: Cafeteria
F.04 FIRE RATED WOODEN SINGLE SHUTTER DOOR : Supply & Installation of Fire Rated Wooden Door of 2 Hrs Fire No's 1.00
Rated including handle, lock set, vision panel, intumescent fire seal strip as per approved drawing & design or
directed by client.
Door Size : 1200 x 2400mm
Hard ware : Dorma
Location : Fire exit
Sub-Total (DOORS)
G.02 MD ROOM MEETING TABLE , LAMINATE FINISHED - SIZE : 2200mm(L) x 1050mm(W) x 750mm(H) No's 1.00
MD ROOM TABLE WITH LAMINATED TOP - SIZE : 2200mm(L) x 1050mm(W) x 750mm(H) : Supply and installation
of MD Room table as per detail drawing :
Base structure made up of plywood and to be finish with 1mm thick approved laminate.
Under Structure: 40x40 mm pipe horizontally fixed with MS leg finished in powder coating of approved color &
shade. Top to be made up of 19mm thk ply finished in 1mm thk laminate of approved color & shade (make -
merino / greenlam) and balancing laminate install on the bottom part of desk. All edges finished with edge
bending tape (make rehau) of approved color & shade.
Electrical Provision : Cable riser and cable carrier to be consider into cost.
POP-UP BOX : Table shall be installed with 2 nos. of Hydraulic Pop-up box with HDMI connector and cable
mangers. All complete as per drawing & supervision of site-incharge.
Location : MD ROOM
G.03 CABIN AREA TABLE WITH SIDE STORAGE, LAMINATE FINISHED - SIZE : 2000mm(L) x 900mm(W) x 750mm(H) No's 1.00
CABIN AREA TABLE WITH LAMINATED TOP - SIZE : 2000mm(L) x 900mm(W) x 750mm(H) & SIDE STORAGE - SIZE :
1200(L) x 450(D) x 750mm(H) : Supply and installation of MD Room table as per detail drawing :
Base structure made up of plywood and to be finish with 1mm thick approved laminate.
Under Structure: 40x40 mm pipe horizontally fixed with MS leg finished in powder coating of approved color &
shade. Top to be made up of 19mm thk ply finished in 1mm thk laminate of approved color & shade (make -
merino / greenlam) and balancing laminate install on the bottom part of desk. All edges finished with edge
bending tape (make rehau) of approved color & shade.
Electrical Provision : Cable riser and cable carrier to be consider into cost.
POP-UP BOX : Table shall be installed with 1 nos. of Hydraulic Pop-up box with HDMI connector and cable
mangers. All complete as per drawing & supervision of site-incharge.
Location : Cabin area table
G.04 FULL HEIGHT STORAGE : LAMINATE FINISH (SIZE - 2000 x 450 x 2400MM) No's 1.00
P/F of FULL HEIGHT STORAGE unit 400 deep in 18mm THK Plywood & 1mm THK Laminate Board (Inside white
&Outside Approved Laminate) including edge binding tape/ laminate of matching colour.
Location : MD Room
G.04 FULL HEIGHT STORAGE : LAMINATE FINISH (SIZE - 1500 x 450 x 2400MM) No's 1.00
P/F of FULL HEIGHT STORAGE unit 400 deep in 18mm THK Plywood & 1mm THK Laminate Board (Inside white
&Outside Approved Laminate) including edge binding tape/ laminate of matching colour.
G.05 MS RACK : Supply and installation of heavy duty MS rack with approved powder coating with steel shelf having No's 1.00
load capacity of 200 kgs. All complete as per the drawing and instruction of site in charge.
Size - 2900mm(L) x 400mm(D) x 2600mm(H) (As per approval)
Location : Store/UPS/Server
H FINISHES
H.01 PLASTC EMULSION PAINT ON CEILING: Providing and applying approved shade plastic emulsion paint on Sqm 135.00
walls/ceiling/gypsum partition etc. as per manufacturer's specification and guideline including surface
preparation, primer coats, and minimum 3 coats roller finish paint to the satisfaction of architect.
H.02 PLASTC EMULSION PAINT ON WALLS & PARTITION: Providing and applying approved shade plastic emulsion Sqm 350.00
paint on walls/ceiling/gypsum partition etc. as per manufacturer's specification and guideline including surface
preparation, primer coats, and minimum 3 coats roller finish paint to the satisfaction of architect.
Sub-Total (FINISHES)
I.02 FIRE EVACUATION PLAN : Supply & Installation of Fire Evacuation Plan- A3 size printed on photoluminiscent No's 2.00
paper sandwiched between 2 nos of 3 mm acrylic panel and fixed on wall with 4 nos of SS studs.
I.03 FIRE EXTINGUISHER SIGNAGE: Fire extinguisher indicator signage of standard size printed on photoluminiscent No's 1.00
paper and stuck on sunboard.
I.04 ROOM NAME PLATE : 3mm thick clear lase cut acrylic sheet with lamination pasted on. - 150 x 55 mm No's 4.00
I.05 FROSTING FILM: Providing and fixing frosted/etching film of1200mm height of approved make on to the glass Sqm 20.00
surface in the location as per detail drawing. The shade/ pattern of frosting/etching film with prototype design
pattern shall be approved by the Architects.
J MISCELLANEOUS ITEMS
J.01 ROLLER BLINDS : Providing and Fixing of Roller Blinder Designed by Arch. Sqm 55.00
Location : External glazing
J.02 KEY BOX : Fabricate and Install Laminated key box with a lockable framed 6mm glass shutter with hooks to hang No's 1.00
the keys. Size 450mm width x 600mm height x 100mm deep.
J.03 MARKER STAND : P/F of marker & duster holder as per approved. No's 1.00
J.04 ARTIFICIAL PLANTS : Supply of artificial plants with PVC planter box of approved design . Lot 1.00
J.05 DEEP CLEANING : Providing of Deep Cleaning of site after civil work finish including of cleaning glass, carpet, floor Sqm 135.00
tile & other as per directed by Engineer Incharge
1.00 SINK: Providing and fixing of Kitchen sink of following material, with R.S. or C.I. brackets painted white, C.P. No. 1
brass chain with rubber plug, 40 mm dia C.P. brass waste of standard pattern and 40 mm dia CP brass `P` trap,
complete including cutting and making good the walls wherever required, of the following make and type: (or
equal approved)
a) Make : Jayna
Type : Single Bowl & Single drain Board
Model : SBFB 01
Overall Size : 460 x380 x 225 mm Deep
Finish : Matt
Material : Fabricated with 1 mm thick SS 304 grade stainless steel sheet
2.0 SINK MIXER: Providing and fixing of 15 mm dia. C.P. brass table mounted Kitchen sink mixer with swivel spout No. 1
and wall flange of following make.(or equal approved). The mixer have flow restrictor for flow rate 3.5LPM
Make : Kohler
Model- Cuff- 2 handle deck-mount kitchen mixer in polished chrome
Cat. No. : K-37316IN-4-CP
Colour/Finish : Chrome
3.00 ANGLE VALVE: Providing and fixing of 15 mm dia brass angle valve (inlet fitting ball valve type) having strainer
screen complete with wall flange of following make and model:(or equal approved)
Make : Schell, Germany
Model no. : 052040699 No. 2
4.00 FLEXIBLE CONNECTION PIPES: Providing and fixing of 15 mm dia, 450 mm long flexible connection pipe having No. 1
EPDM rubber internal core and stainless steel braided outer sheath complete with C.P brass end nuts, of
approved make.
Make : Schell, Germany
Model no. : 052040699
5.00 GEYSER: Providing and fixing electric water storage heater (geyser) of following capacities including making
inlet / outlet connections, of approved makes.
Make: Racold
a) Capacity : 25 litre No. 1
Consideration:-
1. Earthing strips will be provided by base builder.
2. Earthing Pits will be provided by base builder.
B TASK LIGHT FIXTURES - SUPPLY, INSTALLATION, TESTING & COMISSIONING SQM 132
1. Ceiling concealed round lights
2. Linear ceiling concealedlight over W/S & Cabins
3. 600x600 grid light
4. Emergancy lights - Ceiling recessed
5. Cove lights with driver
C E & LV SYSTEM
i Fire Alarm System SQM 132
1. SMOKE DETECTOR with LED & mounting base, including connections, etc complete as required.
2. MANUAL CALL POINT complete with hammer & chain, M.S. box duly painted in red colour including
connections etc. complete as required
3. Electronic solid state HOOTER suitable for wailing tone for fire as required.
4 .Control Panel suitable for following with visual indications of fault and fire on 24V DC system etc.
complete as required job also include integration with BMS.
5. 2x1.5 sq.mm Fire Survival copper conductor armoured cable as required make lapp/ reputed
E HVAC SYSTEM - DUCTABLE AHU SYSTEM WITH OVAL DUCTING SQM 132
1. Supply & Installation of 15 TR Ductable Air Conditioning Units as per Heat load calculation
2. Providing and fixing of GSS (22G,24G) ducting for Supply/ Exhaust air with suitable gauge complete as per
design. And with Insulation(6mm thick) of air ducts complete as per design, Acoustic insulation of
ductswith12mm fiberglass woolrigid boardcovered with RP tissue paper, and the Canvass Connection
3) A/c metal grills Providing and fixing of Extruded Aluminum powder coated Grill ( 6 '').
SUB-TOTAL Rs. - -
REMARK
MODULAR FURNITURE
LX INTERNATIONAL
SL. No. PARTICULARS UNIT QTY RATE AMOUNT RATE AMOUNT REMARK/REF. IMAGE
1 LINEAR TYPE WORKSTATION (SHARING & NON -SHARING - DESKING SYSTEM) No's 6.00
Size : 1400mm x 750mm x 750mm Height
PRODUCT - LINEAR TYPE WORKSTATION
SIZE : 1500 x 750 x 1200HT
Specificaions:
Partition - Slide Based System of 1200HT.
Main Spine - Neo 50mm thick Partition System.
Side Spine - Neo 50mm thick Partition System.
Finish / Tiles -Fabric above and Laminate below table top.
Special Tiles - One fabric magnetic & One glass marker above table top.
Table top - PLB 25mm thick pre-lam particle board finished with 2mm PVC edge banding.
Under-structure - Supported on 18mm thick MS Leg with ms bracket.
Wire Management - Bi Level Raceway on main spine BTT corner frame & Skirting all around the workstation &
450 mm Aluminuum anodised Flip- up with PVC Cable dump.
PRODUCT - PLB MOBILE PEDESTAL (2D+1F)
Size - 400L x 450D x 600HT.
Specifications :
Made of 18mm thick PLB with 2 Drawer +1 Filling unit arrangement, Castors are provided for easy mobility of
the pedestal, Suitable Finger Groove handles, Locking system & other necessary hardware are provided.
6 MODULAR STORAGE UNIT (PLB) - Combination of Open & Closed Storage Cabinets (2400mm Height) Sqm 30.00
Specification:
TOP: 25mm thick PLPB board with 2mm thick PVC edge banding finish with as per approved laminate color.
SHUTTER :18mm thick PLPB board with 2mm thick PVC edge banding finish with as per approved laminate
color.
SHELF (adjustable in height) :18mm thick PLPB board with 2mm thick PVC edge banding finish with as per
approved laminate color.
STRUCTURE :18mm thick PLPB board with 2mm thick PVC edge banding finish with as per approved laminate
color.
HANDLE: Finger groove handle, Door Hinges and Necessary hardwares with Lock
MASTER KEY : Providing of 1 set of master key for every cabinet storage.
7 PRINTER STATION (970mm x 500mm x 750mm) - Pre-lam particle board same as workstation table top. No's 1.00
2 Workstation Chair Mesh Fabric color of seat should be similar to the given reference pic : Nos 8
High back chair with mesh back with lumber support and seat made in high density PU mold,adjustable
arms, synchro mechanism, class 4 gas pump, white nylon base and 55mm castors.
3 Conference room Chair Finish Material Seat Leatherite Shade No. BENTLEY 944 High back chair with fully Nos 8
upholstered back and seat made in high density foam, fixed arms, single lock mechanism,class 4 gas
pump, chrome base and 55mm castors.
4 High back Finish Material Seat Leatherit Base Metal Chrome finish Imported Series back imported chair Nos 2
with fully upholstered back and seat made in high density soft foam , fixed arms, single lock mechanism,
class 4 gas pump,aluminum base and 60mm castors.
SUB-TOTAL
B. LOUNGE FURNITURE
1 SINGLE SEATER SOFA : Single seater high or low back sofa fully upholstered with approved fabric Shade , Nos 3
seat is made with soft foam for extra comfort , SS legs.
Location : Entrance lounge
SUB-TOTAL -
BILL OF QUANTITIES OF ACCESSORIES
S. No. Location Description Unit Total Qty Rate Amount Remarks Reference Photos
Material Labour Total Material Labour Total Amount
1 Cafeteria Refridgerator - LG 240 Ltr 7 wish SNS SHARE CASHBACK GL- Nos. 1.00
S292SPZY
COPY MODEL NAME-240 Ltr, 2 Star, Smart Inverter
Compressor, Convertible, Smart Diagnosis™, Shiny Steel
Finish, Frost-Free Double Door Refrigerator
3 Cafeteria Water Dispenser - 20Ltr Make Bluestar Stella ST4BSHC01 Nos. 1.00
8.2LITRE RO+UV Water Purifier
4 Cafeteria UV Cabinet - Wipro UltraRay Cubix 20 Liters Portable UV-C Nos. 1.00
Disinfectant - Remove 99.9% Bacteria & Viruses Certified by
CSIR-CSIO
5 All Area Dustbin - Pedestral -Steel Pedestal Dustbin, Capacity: 5 ltr Nos. 10.00
6 Cafeteria Dustbin - 45 Ltr (heavy Duty) -ARISTO Plastic Pedal Garbage Nos. 1.00
Waste Dustbin 45 LTR
7 Cafateria Food Warmer- 3 stove-Food Warmer 1803| Buffet Server Nos. 1.00
With 3*1.5L Container Brand Pringle
8 For Cleaning of Powerwash PW-VC-080 3600W 80 L Corded Electric Wet & Nos. 1.00
carpet Dry Vacuum Cleaner
13 SS SKIRTING CUBIX
17 POLISH ASIAN/DULUX/BIZZAR
18 BLINDS VISTA
6 LAMINATE MERINO
10 FROSTED FILM 3M
8 ADHESIVE FEVICOL
HVAC
15 MS PIPING TATA/JINDAL
5 SPRINKLERS TYCO
8 PA SYSTEM BOSCH
PLUMBING
4 CP FITTINGS JAGUAR/KOHLER
8 GEYSERS AO SMITH/HAVELLS
I.T.
2 EPBX MATRIX/ESSL/BINATONE
4 UPS EATON/APC/SCHINDLER