Professional Documents
Culture Documents
Edition: 2020-10
Replaces: 2020-06
Type Z2FS
▶ Size 6
▶ Component series 4X
▶ Maximum operating pressure 350 bar
▶ Maximum flow 80 l/min
H8175
Features Contents
Ordering code
01 02 03 04 05 06 07 08 09 10
Z2FS 6 – 4X / *
02 Size 6 6
Adjustment type
04 Setscrew with lock nut and protective cap (versions "J3" and "J5" without protective cap) 2
Lockable rotary knob with scale 3 2)
Spindle with internal hexagon and scale 5
High corrosion protection (720 h salt spray test according to EN ISO 9227) J5 3)
Seal material (observe compatibility of seals with hydraulic fluid used, see page 5)
08 NBR seals no code
FKM seals V
1 1
Version "–"
P A 2 B T P A 2 B T
1 1
Version "A"
P A 2 B T P A 2 B T
1 1
Version "B"
P A 2 B T P A 2 B T
Notice:
Modification from supply to discharge throttling is realized by
horizontal rotation of the device
Function, section
The valve type Z2FS is a throttle check valve in sandwich The hydraulic fluid return flow from actuator A② displaces
plate design. It is used for the main or pilot flow limitation the valve seat (2) against the spring (5) in the direction of
of one or two actuator ports. the throttle spool (3) and enables the unobstructed flow
Two throttle check valves aligned symmetrically to each as check valve. Depending on the installation position, the
other limit flows in one direction and allow free return flow throttling effect may occur in supply or discharge.
in the opposite direction.
In case of supply throttling, the hydraulic fluid is directed Main flow limitation (version "2Q")
via channel A① via throttling point (1) formed by the valve For actuator velocity adjustment (main flow limitation),
seat (2) and the throttle spool (3) to actuator A②. The the throttle check valve is installed between the directional
throttle spool (3) can be axially adjusted via the set- valve and the subplate.
screw (4) for adjustment of the throttling point (1).
Pilot flow limitation (version "1Q")
With pilot-operated directional valves, the throttle check
valve can be applied for switching time adjustment (pilot
flow limitation). In this case, it is installed between the
pilot control valve and the main valve.
4 5 2 A B
1
3 1 A B
Type Z2FS 6 –2… (supply throttling)
① = component side
② = plate side
Technical data
(For applications outside these values, please consult us!)
General
Z2FS6A./…Z2FS6B./… Z2FS6.-./…
Weight ▶ Version "2" kg 0.9 1.0
▶ Version "3" kg 1.1 1.4
▶ Version "5" kg 1.0 1.2
Installation position any
Ambient temperature range °C –30 ... +80 (NBR seals)
–20 … +80 (FKM seals)
Storage temperature range see operating instructions 07600-B
Hydraulic
Maximum operating pressure bar 350
Maximum flow l/min 80
Maximum leakage (at ∆p 350 bar) l/min < 1
Hydraulic fluid see table below
Hydraulic fluid temperature range °C –30 ... +80 (NBR seals)
–20 … +80 (FKM seals)
Viscosity range mm2/s 10 … 800
Maximum admissible degree of contamination of the Class 20/18/15 1)
Characteristic curves
(measured with HLP46, ϑoil = 40 ±5 °C, averages)
∆p-qV characteristic curves (version "2Q") ∆p-qV characteristic curves (version "1Q")
9
200 200
150 150
10
Pressure differential in bar →
20 20
10 10
5 5
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
Flow in l/min → Flow in l/min →
20
Pressure differential in bar →
15
10
0 10 20 30 40 50 60 70 80
Flow in l/min →
Dimensions
(dimensions in mm)
5
8; 11 4 8; 11 2 1 75 24 20
1
21 0 9 8
"X" "X"
Ø32
38.6
3
22.6
8
46 2 3; 11 12
9
13 12 7
7
10
1.4 61 x 40
14
"X" 18 4 x ø5.4
6
T
7
F1 F2
45
35
A B F3
F4 P G
64
45 81 45
0,01/100
Notice: Rzmax 4
The dimensions are nominal dimensions which are subject to
tolerances. Required surface quality of the
valve contact surface
Further information
Bosch Rexroth AG © All rights reserved to Bosch Rexroth AG, also regarding any disposal,
Industrial Hydraulics exploitation, reproduction, editing, distribution, as well as in the event of
Zum Eisengießer 1 applications for industrial property rights.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No statements
Phone +49 (0) 93 52 / 40 30 20 concerning a certain condition or suitability for a certain application can be
my.support@boschrexroth.de derived from our information. The information given does not release the user
www.boschrexroth.de from the obligation of own judgment and verification.
It must be remembered that our products are subject to a natural process of
wear and aging.