Professional Documents
Culture Documents
6\VWHP Submittal
Prepared by:
Eng.Hassan Mostafa
technical Offic engineer
T: 0120 5005524 Mail : hassan.mostafa@ncc.com.eg
Checked and revised by:
Eng.)DWPD,EUDKLP
Technical Office Manager
T: 0120 50 Mail : fatma.ibrahim@ncc.com.eg
Data Sheets
Technical Data Sheet
X-Shield SF Primer
High performance primer for epoxy coating and floor systems
Datasheet Validity
NCC X-Calibur makes modifications to its product
datasheets on a continuous basis. Please check the
datasheet update section on www.ncc.com.eg to ensure
you have the latest version.
Warranties
NCC X-Calibur supplies products that comply with the
properties shown on the current datasheets. In the
unlikely event that products supplied are proved not to
comply with these properties, then we will replace the
non-compliant product or refund the purchase price.
NCC X-Calibur does not warrant or guarantee the
installation of the products as it does not have control of
the installation or end use of the products. Any suspected
defects must be reported to NCC X-Calibur in writing within
five working days of being detected. NCC X-Calibur
Construction Chemicals. makes no warranty as to
merchantability or fitness for a particular purpose
and this warranty is in lieu of all other warranties
express or implied. NCC X-Calibur Construction Chemicals
shall not be liable for damages of any sort including remote
or consequential damages, down time, or delay.
www.ncc.com.eg
Technical Data Sheet
X-Shield BugFill
High build epoxy bug hole filler, skim coat and general purpose adhesive
Steel
Any damaged steel should be removed and replaced.
The substrate should then be grit blasted to minimum SA
2½. Depending on the level of corrosion protection
required, an anti-corrosion or holding primer may be
necessary. X-Shield BugFill must be applied immediately Warranties
after the grit blasting has been completed. NCC X-Calibur supplies products that comply with the
properties shown on the current datasheets. In the
Mixing unlikely event that products supplied are proved not to
Thoroughly mix the base prior to adding the hardener comply with these properties, then we will replace the
using a slow speed drill (500rpm) fitted with an approved non-compliant product or refund the purchase price.
NCC X-Calibur mixing paddle. After mixing the base, add NCC X-Calibur does not warrant or guarantee the installation
all of the hardener to the base and mix for 3 minutes until of the products as it does not have control over the
both components have fully dispersed and are uniform in installation or end use of the products. Any suspected
color. Be sure to rotate the mixer throughout the drum. defects must be reported to NCC X-Calibur in writing within
Mix only full packs. five working days of being detected. NCC X-Calibur
Construction Chemicals. makes no warranty as to
Application merchantability or fitness for a particular purpose
Apply using trowel, scraper or filling knife, using a ‘scrape and this warranty is in lieu of all other warranties
on, scrape off’ technique to completely fill bug (blow) express or implied. NCC X-Calibur Construction Chemicals
holes and imperfections. Bug holes or imperfections shall not be liable for damages of any sort including remote
greater than 10mm will require to be filled in two or more or consequential damages, down time, or delay.
layers, with the first layer being allowed to harden before
application of the subsequent layer. Recoat after 16 to 24
hours at 25C or 8 to 16 hours at 35C. Clean uncured
material from equipment using X-Shield Solvent S. Cured
material can only be removed by mechanical means.
Limitations
Will change color when exposed to direct sunlight.
Will not accommodate movement cracks.
Do not apply below 4C
Do not discard into the water system.
Protect from chemical and water spillage until fully cured.
Datasheet Validity
NCC X-Calibur makes modifications to its product
datasheets on a continuous basis. Check the current
datasheet section on www.ncc.com.eg to ensure you have
the latest version.
www.ncc.com.eg
Technical Data Sheet
www.ncc.com.eg
Test Reports
#**"*
{sffi
.s-o
ffi*il
&
n&\
-
#ilJ
-6FR1*
g \> Ll+rllriiiltr d''!:$ c.r'It 5-+";r
I
Jl$iI Crfri
OLar 4+l
X-Tech AntiStatic SLE
X- CALIBUR ( NCC) asJ4 a-,al3ll
Prof. Ma
lls*,:gj"-$r Fr,jt )*3,8{ B3P{3{ffi;r,rs-! }+ffi ft3$#r?,'$E-.H.5{.3III3 ;,.ir;-:U i3\53r - }--i"i+}E -.-;*;"r}t r**{
.n*"S&rm*dEtsEswoc t-, Iiewffi$*-oCaira"E"Hry*- T*k{+!,1}?}E3?{'?SI?133:?4?&{.? Fam: {"i-396}3::?S?4S;} F-S,:11?I
mwm-*gffii-xe{-qg moffi {}[8$3$Sii3ffi" fc]{*3}67#7$p E ma,i&;dstrucltedrs ffiEmatrLcsm
ffi
]N,SAC @n@
-fFRl-
q6. )Y
\#t-'**'F if
ffi,'ffiHHi
Egyptian Petroleum Research lnstitute (EPRI)
EltIF z .,i r- ^ir i ,t ^^ r( . -
-L...\!r
JtSil Cjtii
Olir 4irrl
X-Tech AntiStatic SLE Grey
x-cAlt BU R (N ccles* Latitt
Recived sample date is 22 l4l2020
,,#**
.tl . ZaLd
M"y
lll2l-*s-;j-.i"+ FtSS( EH!,#B :r*i Fg,{ ftrlB?ffi,- !|ft/ffl1:1,::'r|rfii9'5r -Jr-:i+-u -r*3 u*!
-l 1
LABORATORYREPORT
X-CaliburlnternationalFZC ReportNo:WLRl2-1704
P.OBox120636 SampleNo:WS12-0833/1
Sharjah,
U.A.E. Dateof Report:3'l/03/2012
SampleDescription X-TechAntiStaficSLE
Sampleldentification xcuPo128t12
SampleReceived 28/03t2012
Test Method ASTMD638
Dateof Test 28t43t2012
Age of T€st 7 days
T€st€dBy JB
TensileandElonqation
TechnlcalManager
Testresultsrelateony lo lhesampeslesled.
Thisreporlshallnotbereproduedex@ptinfull withoullheMiiten?ppbvalotthela
LABORATORY
REPORT
X-CaliburInternationalFZC ReportNo:WLR12-1506
P.OBox'120636 SampleNoiWS12-0811
Sharjah,
U.A.E. Dateof Report:26/03/2012
SampleDescription X-Tech
Antistatic
SLE
Sampleldentification xcvPo122t12
SampleP.eparedby Clieni
SampleReceived 25t0312012
TestMethod ASTMD 2794
Dateof Test 25t0u2412
Age of test 7 days
TestedBy JB
l mp a c t R e s i s t a n c e :
TestMethod:Thesuppljedsamplewastestedin accordance
withASTIMD-2794
Diameter
of pun6h :12mm
Height
of Indeniion : 1.75m
l\Iassof thecyljnder i 0 . 9 7 8k g
7.0 Priming
The base and hardener have to mixed using a slow speed drill and approved mixing
paddle until homogenous. The mixed primer should then be applied to the prepared
substrate with a stiff brush or roller. Do not over apply or allow puddles of primer to
form. If the primer is absorbed into the surface easily, it will be necessary to apply
a second coat once the initial coat is tack-free.
8.0 Grounding
12.0 Testing
Allow the floor to cure for 2 days and test for conductivity using the test method
given in ASTM F150 and the results recorded. The average resistance for a
conductive floor should be between 5 x 104 ohms and 1 x 106 ohms and for a
dissipative floor it should be between 5 x 106 ohms and 1 x 109 ohms. It is
recommended that 1 reading is taken at least every 50m2.
13.0 Safety
This product is for industrial use only by trained operatives.
The application team should use the following personal protection equipment:
• Eye protection
• Gloves
• Rubber soled safety shoes
• Coveralls
When using electrical equipment such as mixers ensure that they are properly fused
and earthed with the correct plug and sockets fitted.
Do not use electrical equipment if it will come into contact with water.
14.0 Limitations
Can change color in when exposed to direct sunlight.
Will not accommodate movement cracks.
Do not apply below 10C.
Avoid excessive application.
Avoid skin contact.
Do not dispose off into the water system
16.0 Warranties
X-Calibur supplies products that comply with the properties shown on the current
datasheet. In the unlikely event that products supplied are proved not to comply
with the properties, then we will replace the non-compliant product or refund the
purchase price.
X-Calibur does not warrant or guarantee the installation of the products, as it does
not have control of the installation or end use of the product. Any suspected
defects must be reported to X-Calibur in writing within five working days of being
detected.
Kenyatta University
China Jiangxi Kenyatta X-Tech AntiStatic
5. Teaching, Research & Nairobi,Kenya Hospitals or Clinic Kenyatta University Feb 2016 1428 m²
International Univesity SLE
Referral Hospital
X-Tech AntiStatic
6. Studio 8, Abu Dhabi Abu Dhabi,UAE Shopping Center Smartcrete N/A Studio 8 Mar 2015 800 m²
SLE
Residential or
Intaj Production X-Tech AntiStatic
8. Twofour54 TV Studio Abu Dhabi,UAE Commercial Smartcrete Derwent International Apr 2014 610 m²
Services SLE
Building
No. Project Location Project Type Contractor Consultant Owner Product Date Supplied Quantity
Bayer Crop Science Residential or
X-Tech AntiStatic
9. Formulation Unit Safety Bein Hoa,Vietnam Commercial VietViet Bayer Bayer Mar 2014 560 m²
SLE
Upgrade Building
Residential or
Test Area in Clean Engineering Intel X-Tech AntiStatic
10. Ho Chi Minh,Vietnam Commercial Atea Intel Jul 2013 3000 ft²
Room at Intel Vietnam Services SLE
Building
Industrial
Printed Circuit Board Project X-Tech AntiStatic
11. Gauteng,South Africa Industrial Contracting Owner Oct 2012 600 m²
Manufacturing Unit Concern Pty SLE
Services
X-Tech AntiStatic
13. Hoya Factory Hanoi,Vietnam Industrial Obayashi Not known Not known May 2008 1750 ft²
SLE
Material Safety Data Sheets
X-Tech AntiStatic SLE TopCoat - Base
X-Tech AntiStatic SLE Topcoat - Filler
X-Tech AntiStatic SLE Topcoat - Hardener
MATERIAL SAFETY DATA SHEET
A. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY UNDERTAKING
E-mail: tech@x-calibur.us
All constituents of this product are listed in EINECS (European Inventory of Existing Commercial Substances)
or ELINCS (European List of New Chemical Substances) or are exempt.
C. HAZARDS IDENTIFICATION
Environmentally hazardous
Irritating to eyes and skin.
May cause sensitization by skin contact
Irritant Hazardous to
the environment
Issue No: 2 Date: December 2014 Product Name: X-Tech AntiStatic SLE Topcoat Base Page 1 of 5
E. FIRE FIGHTING MEASURES
Personal Precautions: Wear suitable protective clothing, gloves and eye protection.
Environmental Precautions: Prevent entry into drains, sewers and water courses.
Decontamination Procedures: Soak up with inert absorbent or contain and remove by best available
means.
Gather into containers.
Dispose of as waste.
Issue No: 2 Date: December 2014 Product Name: X-Tech AntiStatic SLE Topcoat Base Page 2 of 5
J. STABILITY AND REACTIVITY
K. TOXICOLOGICAL INFORMATION
The following toxicological assessment is based on knowledge of the toxicity of the products components.
Expected oral LD50, rat >2g/kg.
Classified as skin sensitizer.
Health Effects:
L. ECOLOGICAL INFORMATION
M. DISPOSAL CONSIDERATION
Issue No: 2 Date: December 2014 Product Name: X-Tech AntiStatic SLE Topcoat Base Page 3 of 5
N. TRANSPORT INFORMATION
Additional Information
ADR-HIN: 90
IMDG-EMS: F-A, S-F Marine Pollutant: Yes
IMO: T1
O. REGULATORY INFORMATION
Issue No: 2 Date: December 2014 Product Name: X-Tech AntiStatic SLE Topcoat Base Page 4 of 5
P. ECOLOGICAL
The data and advice given apply when the product is used for the stated application or applications. The
product is not sold as suitable for any other application. Use of the product for any application other than as
stated in this sheet may give rise to risk not mentioned in this sheet. The product may not be used other than
for the stated applications without seeking advice from X-Calibur Constructions System Inc.
If this product has been purchased for supply for a third party for use at work, it is the purchasers duty to
take all the necessary steps to secure that any person handling or using the product is provided with the
information of this sheet. It is the responsibility and duty of the employer to inform employees and others
who may be affected in hazards described in this sheet and of any precautions which should be taken.
This sheet does not constitute or substitute for the other users own assessment of workplace risk, as required
by the other health and safety legislation.
Issue No: 2 Date: December 2014 Product Name: X-Tech AntiStatic SLE Topcoat Base Page 5 of 5
MATERIAL SAFETY DATA SHEET
A. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY UNDERTAKING
E-mail: tech@x-calibur.net
B. COMPOSITION/INFORMATION OF INGREDIENTS
Harmful if swallowed.
Dust irritant
General information: In all cases of doubt, or when symptoms persists, seek medical
attention. Never give anything by mouth to an unconscious person.
Eyes: Check for and remove contact lenses if any. Irrigate copious amount of
water for several minutes keeping eye lids open. Obtain medical
attention if problem persists.
Skin: Wash thoroughly with soap and water or suitable skin immediately.
Obtain medical attention if problem persists.
Inhalation: Remove to fresh air. If not breathing, provide artificial respiration. Seek
medical attention if the problem continues.
Ingestion: Do not induce vomiting. Obtain medical attention and show the
container or label.
Issue No: 1 Date: 02/12/2006 Product Name: X-Tech AntiStatic SLE Topcoat Filler Page: 1 of 4
E. FIRE FIGHTING MEASURES
Environmental Precautions: Prevent entry into drains, sewers and water courses.
Silica amorphous:
total inhalable dust 5 mgm-3 ---- EH 40
respirable dust 3 mgm-3
Portland cement:
total inhalable dust 10 mgm-3 ----- EH 40
respirable dust 5 mgm-3
Engineering Control Measures: Atmospheric levels of dust must be maintained within the
Occupational Exposure Standard. Where mechanical methods
are inadequate, appropriate personal protective equipment must
be used.
Personal protective Equipment: Impervious gloves (eg PVC). Goggles. Approved dust mask.
Issue No: 1 Date: 02/12/2006 Product Name: X-Tech AntiStatic SLE Topcoat Filler Page: 2 of 4
I. PHYSICAL AND CHEMICAL PROPERTIES
Color: Various
Odor: -
Solubility: Insoluble
K. TOXICOLOGICAL INFORMATION
Silica based materials are known to cause both irritant and allergic contact dermatitis.
Harmful by inhalation and if swallowed.
L. ECOLOGICAL INFORMATION
When used and disposed as intended, no adverse environmental effects are foreseen. Expected to be not
readily bio-degradable. Bio-accumulative potential and ecotoxicity are not determined.
M. DISPOSAL CONSIDERATIONS
Do not allow to enter into drains or watercourses. Material and container must be disposed as hazardous
waste.
N. TRANSPORT INFORMATION
Class: -
Subsidiary risk: -
Issue No: 1 Date: 02/12/2006 Product Name: X-Tech AntiStatic SLE Topcoat Filler Page: 3 of 4
Packaging group -
Label: -
Additional information -
ADR-HIN -
IMO: -
O. REGULATORY INFORMATION
Hazard Symbol(s) Xn
P. DISCLAIMER
To the best of our knowledge, the information provided herein is accurate, obtained from sources
believed to be accurate. Since the conditions and methods of use of our product are beyond our control,
we disclaim any and all liability arising out of the improper use of this product or the information
provided herewith.
Issue No: 1 Date: 02/12/2006 Product Name: X-Tech AntiStatic SLE Topcoat Filler Page: 4 of 4
MATERIAL SAFETY DATA SHEET
A. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY UNDERTAKING
B. COMPOSITION/INFORMATION OF INGREDIENTS
Corrosive.
May cause burns.
Toxic to aquatic organisms.
CORROSIVE HAZARDOUS
General information: In all cases of doubt, or when symptoms persist, seek medical
attention. Never give anything by mouth to an unconscious person.
Eyes: Check for and remove contact lenses if any. Irrigate copious amount of
water for several minutes keeping eye lids open. Obtain medical
attention if problem persists.
Skin: Wash thoroughly with soap and water or suitable skin immediately.
Obtain medical attention if problem persists.
Inhalation: Remove to fresh air. If not breathing, provide artificial respiration. Seek
medical attention if the problem continues.
Ingestion: Do not induce vomiting. Obtain medical attention and show the
container or label.
Issue No: 2 Date: 02/07/20014 Product Name: X-Tech AntiStatic SLE Topcoat Page: 1 of 4
Hardener
E. FIRE FIGHTING MEASURES
Suitable extinguishing Media: Dry chemical, foam, carbon dioxide or water spray.
Personal Precautions: Wear gloves and other suitable clothing including eye/face
protection.
Environmental Precautions: Prevent entry into drains, sewers and water courses.
Decontamination procedures: Soak-up with inert absorbent or contain and remove by best
available means. Gather into containers. Dispose of as waste.
Handling: Avoid skin and eye contact. Do not eat, drink or smoke whilst
using this product. Ensure adequate ventilation.
Engineering Control Measures: Use with adequate general and local exhaust ventilation.
State: Liquid
Color: Amber
Solubility: Miscible
Issue No: 2 Date: 02/07/20014 Product Name: X-Tech AntiStatic SLE Topcoat Page: 2 of 4
Hardener
J. STABILITY AND REACTIVITY
Conditions to avoid: Excess heating over long period of time degrades the resin.
Materials to avoid: Mineral and organic acid, strong oxidizing agent, organic
halides.
K. TOXICOLOGICAL INFORMATION
There are no date available on the preparation itself. This has been assessed following the conventional
method of the Preparations Directive 1999/45/EC and classified for toxicological hazards accordingly.
Based on the properties of the epoxy constituent(s) and considering toxicological data on similar
preparations, this product may be a skin sensitizer and irritant. May produce allergic reactions. May
cause damage to eyes.
L. ECOLOGICAL INFORMATION
When used and disposed as intended, no adverse environmental effects are foreseen. Expected to be not
readily bio-degradable. Bio-accumulative potential and ecotoxicity are not determined.
M. DISPOSAL CONSIDERATIONS
Do not allow to enter into drains or watercourses. Material and container must be disposed as hazardous
waste.
N. TRANSPORT INFORMATION
UN Number: 2735
Class: 8
Subsidiary risk: -
Additional information -
ADR-HIN 80
IMO: -
Issue No: 2 Date: 02/07/20014 Product Name: X-Tech AntiStatic SLE Topcoat Page: 3 of 4
Hardener
O. REGULATORY INFORMATION
Hazard Symbol(s) C, Xn
Contains: Polyamines
P. DISCLAIMER
To the best of our knowledge, the information provided herein is accurate, obtained from sources
believed to be accurate. Since the conditions and methods of use of our product are beyond our control,
we disclaim any and all liability arising out of the improper use of this product or the information
provided herewith.
Issue No: 2 Date: 02/07/20014 Product Name: X-Tech AntiStatic SLE Topcoat Page: 4 of 4
Hardener
USA
5000 SW 52nd Street, Suite 508
Davie, FL 33314, USA
T +1 954 885 9912
F +1 954 885 9913
E info@x-calibur.net
Hong Kong
16 F. Bangkok Bank Building
18 Bonham Strand West
Hong Kong
T +852 2838 9393
F +852 2851 2891
E thoronhk@netvigator.com
Tunisia
Rue De Annaba-Z.I Ben Arous 2013
BP-291-Ben Arous
Tunisia
T +216 7138 2929
F +216 7138 6822
UAE
PO Box 25973
Dubai-UAE
T +9714 331 4050
F +9714 332 9107
E apitech@eim.ae
Export Sales
PO Box 120636
SAIF Zone
Sharjah-UAE
T +9716 557 9460
F +9716 557 9461
E export@x-calibur.us
www.x-calibur.us