Professional Documents
Culture Documents
Contents
1. CHEMICAL PRODUCT & COMPANY IDENTIFICATION: .................................................................................. 2
1.2. Relevant identified uses of the substance or mixture and uses advised against
Company Name: ABB Furse (ABB Ltd.), Wilford Road, Nottingham NG2 1EB
United Kingdom.
2. HAZARDS IDENTIFICATION:
Causes severe skin burns and eye damage. May cause an allergic skin reaction. May cause respiratory irrita-
tion.
GHS05 GHS07
Hazard statements (CLP): H314 - Causes severe skin burns and eye damage.
Precautionary statements (CLP): P280 - Wear protective clothing, eye protection, face
protection.
3. COMPOSITION/INFORMATION ON INGREDIENTS:
3.1. Substances
Not applicable
3.2. Mixtures
(REACH-no) Exempt
First-aid measures general: If you feel unwell, seek medical advice. Show this sheet
where possible. If not available, show packaging or label.
First-aid measures after inhalation: Remove person to fresh air and keep comfortable for
breathing.
First-aid measures after skin contact: Wash skin with plenty of water and soap. Take off
contaminated clothing.
First-aid measures after eye contact: Rinse immediately with plenty of water (for at least 15
minutes). Remove contact lenses, if present and easy to do.
Continue rinsing. Get immediate medical advice/attention.
First-aid measures after ingestion: Get immediate medical advice/attention. Do not induce
vomiting. Rinse mouth out with water. Drink plenty of water.
Never give anything by mouth to an unconscious person.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/effects after inhalation: Inhalation of dust: May cause shortness of breath, tightness
of the chest, sore throat and coughing. May cause respira-
tory irritation.
Symptoms/effects after skin contact: May cause severe burns. May cause an allergic skin reaction.
4.3. Indication of any immediate medical attention and special treatment needed
Treat symptomatically.
Suitable extinguishing media: The product is not flammable. Adapt extinguishing media
to the environment.
General measures: Ventilate spillage area. Mark out the contaminated area with
signs and prevent access to unauthorized personnel.
Avoid release to the environment. Do not allow to enter drains or water courses.
Methods for cleaning up: Shovel or sweep up and put in a closed container for
disposal. Minimize generation of dust.
Precautions for safe handling: Ensure good ventilation of the work station. Wear personal
protective equipment. For further information refer to sec-
tion 8: "Exposure controls/personal protection".
Hygiene measures: Do not eat, drink or smoke when using this product.
Always wash hands after handling the product.
Odour: Odourless.
10.1. Reactivity
Water, humidity.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Combustion generates: Carbon dioxide/carbon monoxide.
12.1. Toxicity
European List of Waste (LoW) code: 10 13 11 - wastes from cement-based composite materials
other than those mentioned in 10 13 09 and 10 13 10
14.1. UN number
Not applicable Not applicable Not applicable Not applicable Not applicable
Not applicable Not applicable Not applicable Not applicable Not applicable
Not applicable Not applicable Not applicable Not applicable Not applicable
Not applicable Not applicable Not applicable Not applicable Not applicable
Not applicable Not applicable Not applicable Not applicable Not applicable
14.7. Transport in bulk according to Annex II of Marpol and the IBC Code
Not applicable
15.1. Safety, health and environmental regulations/legislation specific for the substance or
mixture
15.1.1. EU-Regulations
STOT SE 3 Specific target organ toxicity — Single exposure, Category 3, Respiratory tract
irritation
16.2. Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and
belief at the date of its publication. The information given is designed only as a guidance for safe handling,
use, processing, storage, transportation, disposal and release and is not to be considered a warranty or qual-
ity specification. The information relates only to the specific material designated and may not be valid for
such material used in combination with any other materials or in any process, unless specified in the text.