Professional Documents
Culture Documents
Page 1 of 10
INSTALLATION
1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
(a) Using a vernier caliper and straightedge, measure dimension A between the transmission and the
end surface of the drive plate.
Standard distance:
B = A + 1.00 mm (0.0394 in.) or more
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 2 of 10
NOTICE:
Be careful not to damage the oil seal of the transfer adapter.
(b) Install the transfer case lower protector with the 7 bolts.
(c) Connect the clamp of grand cable to the transfer case lower protector.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 3 of 10
breather tube.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 4 of 10
NOTICE:
Check that the 2 straight pins are attached to the
engine side.
NOTICE:
Make sure the pinching portion of each clip is facing the
direction shown in the illustration.
Make sure the paint mark of each hose is facing
outward.
(a) Connect the 2 water by-pass hoses with the 2 clips and
install the water by-pass pipe with the bolt.
NOTICE:
Make sure the pinching portion of each clip is facing the
direction shown in the illustration.
Make sure the paint mark of each hose is facing
outward.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 5 of 10
(a) Connect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed
sensor connectors and 3 transfer control side connectors.
HINT:
Push up the lever until the claw of the transmission wire connector makes a connection sound.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 6 of 10
(a) Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 7 of 10
12. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
(a) Turn the crankshaft to gain access to the installation locations of the 6 bolts and install the bolts
while holding the crankshaft pulley set bolt with a wrench.
NOTICE:
First install the black colored bolt and then the remaining 5 bolts.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 8 of 10
(b) Check that the shift lever does not stop when moving the shift lever from R to P, and check that
the shift lever does not stick when moving the shift lever from D to S.
(c) Start the engine and make sure that the vehicle moves forward after moving the shift lever from N
to D and moves rearward after moving the shift lever to R.
If there are problems during the above inspections, perform the adjustment using the following
procedures.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISS... Page 9 of 10
(2) Loosen the nut of the floor shift gear shifting rod.
Then, with the lever of the floor shift assembly lightly
pushed towards the rear of the vehicle, tighten the
nut.
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMI... Page 10 of 10
https://techinfo.toyota.com/t3Portal/document/rm/RM13N0U/xhtml/RM0000018ZB01T... 12/27/2010