Professional Documents
Culture Documents
MUSTAFA FAKHER
2nd Semester/ 4th Grade
Communications
2023-2024
COMMUNICATIONS LAB 1
Experiment-1
Battray voltage & Battary charging
1-Theory:
The electrical specifications for the battery connector are shown in Table.
It consists of three terminals.
1. Battery +Ve.
2. BSI.
3. Ground.
Pin 1: Battery Voltage (VBATT): This is the supply Pin of the battery; it
supplies power to the system and also acts as a charging terminal.
Pin 2: Battery Size Indicator (BSI): The battery status/size is indicated by
a resistor inside the battery pack.
Pin 3: Ground (GND): This pin is directly connected to ground.
2-Requairments:
1.4G LTE Smart Phone TechBook
2. SIM card(s) of any 4G service provider supporting 4G LTE frequency
band
3. Power Supply for Scientech 2139 with Mains Cord
4. Hands free kit.
COMMUNICATIONS LAB 2
3-Operating mode:
4G Mobile Phone training system works in two operating
mode that can be selected by a Mode Selection Switch provided on the
TechBook at left side near Power connector.
1- Battery Mode (Switch Released): In this mode the TechBook operates with
battery supplied & battery can be charged.
2-Adaptor Mode (Switch Pressed): In this mode the TechBook operates on
external Power Supply.
For this connect Scientech 2139 Power supply with mains cord to TechBook.
4-Operating Condition:
1. Follow all the conditions as instructed in Experiment 1.
2. Check that all the Switch Faults should be in off position.
5-Procedure:
1. Once the TechBook is initially ready as per the set up given in
Experiment I and if it detects the 4G service provider network(s) with
sufficient network strength, further experiment can be done with this
TechBook as follows.
2. Observe the different voltages used for various sections as per the table given
below.
COMMUNICATIONS LAB 3
6-Disscuion:
The positive terminal (+) is the pin of the battery connector where the positive
terminal of the battery touches on it. It is also called vBat (Battery Voltage) pin.
While negative terminal (-) is the pin of the
battery connector where the negative terminal
of the battery touches on it. It is also called GND (Ground) pin.
BSI pin performs very important functions and
act as an interface between the Mobile phone and the Battery.
COMMUNICATIONS LAB 4
7-Result:
Discussion
# name pins Adabter mode
Battery is not
1 VBATT pin 13 5.03,5.05 efficient
Battery is not
2 SBI pin 14 0.02,0.25 efficient
GND is always 0
3 GND pin 15 0.00
COMMUNICATIONS LAB 5
Experiment-2-
Power management unit
1-Theory:
Power supply management unit supplies the power to all the section of
the mobile phone. There are following Power Supply sections.
Logic Power Supply: This Power Supply section provides the Power
Supply for RTC, Alert VCC supply, Audio processor Power Supply, CPU
section, Memory section, SIM switcher section, User Interface section,
LCD display, Keypad LED indication etc.
2-Requairments:
1.4G LTE Smart Phone TechBook
2. SIM card(s) of any 4G service provider supporting 4G LTE frequency
band
3. Power Supply for Scientech 2139 with Mains Cord
4. Hands free kit.
COMMUNICATIONS LAB 6
3-Operating mode:
4G Mobile Phone training system works in two operating
mode that can be selected by a Mode Selection Switch provided on the
TechBook at left side near Power connector.
1- Battery Mode (Switch Released): In this mode the TechBook operates with
battery supplied & battery can be charged.
2-Adaptor Mode (Switch Pressed): In this mode the TechBook operates on
external Power Supply.
For this connect Scientech 2139 Power supply with mains cord to TechBook.
4-Operating Condition:
1. Follow all the conditions as instructed in Experiment 1.
2. Check that all the Switch Faults should be in off position.
5-Procedure:
1. Once the TechBook is initially ready as per the set up given in
Experiment I and if it detects the 4G service provider network(s) with
sufficient network strength, further experiment can be done with this
TechBook as follows.
2. Observe the different voltages used for various sections as per the table given
below.
COMMUNICATIONS LAB 7
6-Disscuion:
Power management broadly refers to the management of power-related
activates in a mobile device, which include generation, storing,
distribution, conservation, and control of regulated voltages
required to operate the host mobile system. The power management unit
in mobile phone can be divided into two sections; the power distribution
and switching unit, and the charging unit. Power distribution section is
used for the distribution of voltage and current to the other components
of the smartphone. This section is generally part of an analog baseband
(ABB) unit.
It takes power from the battery and converts it to various voltages such as 4.8 V,
2.8 V, 1.8 V and 1.6 V, and distributes it to other components. Charging section
is responsible for charging the battery of the mobile phone. It is composed of
acharging integrated circuit, which takes power from an external source and
charges the battery of the smartphone.
COMMUNICATIONS LAB 8
7-Result:
COMMUNICATIONS LAB 9
COMMUNICATIONS LAB 10
UOITC, COLLGE OF ENGINEERING
MUSTAFA FAKHER
2nd Semester/ 4th Grade
Communications
2023-2024
COMMUNICATIONS LAB 1
Experiment-3:part 1
1- Objective:
study and analysis the buzzer in 4G LTE smart phone techbook
2-Requairments:
1. 4G LTE Smart Phone TechBook
2. SIM card(s)
3. Power Supply for Scientech 2139 with Mains Cord
4. Hands free kit.
5. Oscilloscope
3-Operating mode:
4G Mobile Phone training system works in two operating
mode that can be selected by a Mode Selection Switch provided on the
TechBook at left side near Power connector.
2-Adaptor Mode (Switch Pressed): In this mode the TechBook operates on
external Power Supply.
For this connect Scientech 2139 Power supply with mains cord to TechBook.
COMMUNICATIONS LAB 2
4-Operating Condition:
1. Follow all the conditions as instructed in Experiment 1.
2. Check that all the Switch Faults should be in off position.
5-Procedure:
1- press menu button
4- select normal and press edit then select call alert type and press change then
select melody mode and save
5- go back and select voice call ring tone —> press change —> select any tone
6- go back select volume and check the volume of call alert —> save it
and go back to enational window
COMMUNICATIONS LAB 3
6-Result:
COMMUNICATIONS LAB 4
Part2 :vibrator
1- Objective:
study and analysis the buzzer in 4G LTE smart phone techbook
2-Requairments:
1. 4G LTE Smart Phone TechBook
2. SIM card(s)
3. Power Supply for Scientech 2139 with Mains Cord
4. Hands free kit.
5. Oscilloscope
3-Operating mode:
4G Mobile Phone training system works in two operating
mode that can be selected by a Mode Selection Switch provided on the
TechBook at left side near Power connector.
2-Adaptor Mode (Switch Pressed): In this mode the TechBook operates on
external Power Supply.
For this connect Scientech 2139 Power supply with mains cord to TechBook.
COMMUNICATIONS LAB 5
4-Operating Condition:
1. Follow all the conditions as instructed in Experiment 1.
2. Check that all the Switch Faults should be in off position.
5-Procedure:
1- press menu button
4- select normal and press edit then select call alert type and press change then
select vibration mode and save
COMMUNICATIONS LAB 6
6-Result:
7-Discussion:
Sound waves are the mechanical vibrations of a medium which are
then transferred to and interpreted by some sort of recording device, either living or tech in
origin, as sound. But not all vibrations produce audible or recordable sound. If you were
floating in space and detonated an explosive nearby, you would not hear it
because there is no medium, in this case air, to transfer vibrations to your eardrums.
There are sound waves waves higher than the range of human hearing
the range of human hearing, less than 20 cycles per second, are referred to as infrasound.
COMMUNICATIONS LAB 7
COMMUNICATIONS LAB 8
UOITC, COLLGE OF ENGINEERING
MUSTAFA FAKHER
2nd Semester/ 4th Grade
Communications
2023-2024
COMMUNICATIONS LAB 1
Experiment-5
1- Objective:
Study and analyse mic and speaker section
2-Requairments:
1-4g lte smartphone tiehbook
4-Oscilloscope
3-Operating mode:
4G Mobile Phone training system works in two operating
For this connect Scientech 2139 Power supply with mains cord to TechBook.
4-Operating Condition:
1. Follow all the conditions as instructed in Experiment 1.
5-Procedure:
1- when the techbook is initially ready and if it detects the 4g services provider network with
sufficient network strength the exprement can be done
COMMUNICATIONS LAB 2
2- make a call to the techbook and receive a call now the volume of the speaker can be
increased or decreased using up down key .
4-observe the received oudio signal from caller at the speaker test point in user interface
section
5- observe transmittied oudio signal at the mic test point in user interface section
6-Result:
Transmitter:
COMMUNICATIONS LAB 3
Reciver :
COMMUNICATIONS LAB 4