Professional Documents
Culture Documents
ESP
Function Symbol
Model Code
ESPP-H(2)-H(20)-10
1 2 3 4 5 6 7
L
Omit: 1 contact, variable deadband *1. HN type not applicable with 4 ‘Omitted for 1 contact, variable
deadband’.
2: 2 contacts, fixed deadband
*2. 6 20: Water proof type is applicable with 4 ‘3: 1 contact, fixed
3-1
3: 1 contact, fixed deadband deadband’.
Switches and Sensors
Specifications
●●Sensing, Output ●●Environment, Construction
Rated pressure: Working temperature range: -20 to +70°C
Allowable humidity range: 5 to 90%RH
Code
記号 L1 L H H1
Insulation resistance: Above 100 MΩ (at DC50V)
MPa 1 10 35 50
Voltage resistance: AC350 V 1 min.
Sensing pressure setting method: rotary variable resistor (measured current above 5 mA)
(3 turns) Vibration resistance: JIS D 1601 steps 70 X, Y, Z direction
Contact method: upper limit contact (transistor ON when Shock resistance: JIS C 0912-1984 196 m/s2 X, Y, Z direction
pressure rises to setting pressure) Cycle durability: above 107 times
Deadband:
可変式
Variable 2~10%F.S. Note: When measuring the insulation resistance, do not apply
固定式
Fixed 1%F.S. (TYP.) a voltage of DC 50V or higher.
Indicator: LED
Power supply and output rating: see “Model Code”
Cable: 3 core (4 core) cable 2000 mm
Repeatability: less than ±0.2% F.S.
Temperature characteristic:
Drip
防滴形 proof Less than
±0.05 ±0.05% F.S.
%F.S.以内
Water
防水形 proof Less than
±0.1 ±0.1% F.S.
%F.S.以内
Response: less than 1ms
Fluctuating voltage effect: less than ±0.1% F.S.
Specifications
Water Resistance: ●●Internal circuit
JIS C 0920 IP67 Water
防水形 proof Regulator +V
JIS D 0203-M2 Drip
防滴形 proof (Red)
P.S.M .
OUT
Wetted surface material: SUS630 or SUS316 (White)
Mounting thread: R1/4 or G1/4 Amplifier Comparator
Weight:
440 g Water
防水形 proof
SET
200 g Drip
防滴形 proof DIFF LED
COM
(Black)
●●Open Collector Output Application Example
HN (PNP-VDE standard) H (NPN)
Relay
Transistor protection diode
Relay output
(Black) (Black)
Power (-) Power (-)
Note: Voltage and current ratings of coil of Note: Voltage and current ratings of coil of
relay should be within ratings of transistor. relay should be within ratings of transistor.
Pull up resistor
L
(White) Output (White) Output
Voltage Voltage
Pull down resistor
LH (low/high) output HL (high/low) output 3-2
(Black) (Black)
Power (-) Power (-)
Notes on Operation
●●Surge pressure may vary depending on the design of the circuit (3) Gradually turn SET in direction opposite of UP, and stop at
but surges 2 to 5 times greater than circuit pressure may be point when output switches ON (LED lights). This completes
generated. Use restrictor fittings to protect equipment under “ON pressure” setting.
such conditions. (4) Turn DIFF in the direction of INC and maximize deadband.
●●Adjust trimmer for pressure setting while observing pressure (5) Reduce pressure to the unit to the desired OFF point and fix
gauge. After setting, confirm contact points using the LED display. (value of OFF point is ON point reduced by the deadband).
Make sure to tighten trimmer with drip proof cap after adjustment. (6) Gradually turn DIFF in the direction opposite of INC, and stop at
●●Setting procedure (refer to Fig. A) point when output switched OFF (LED extinguished). This fixes
These pressure switches establish a difference in the “OFF pressure,” and the pressure switch setting is completed.
pressure at which they turn ON and OFF in order to (7) Raise and lower pressure and confirm ON, OFF function
safeguard against chattering near the set pressure. This (LED ON, OFF).
pressure difference is referred to as the deadband. The
UP
adjustment trimmer used to set the deadband is marked
“DIFF.” The adjustment trimmer used to set the pressure
at which the switch is turned ON is marked “SET.” DIFF is
used to set the difference from SET. Setting
Setting procedures Pressure ON
(1) First turn pressure setting trimmer (SET) in UP direction to (SET)
OFF
set pressure at maximum then turn deadband adjustment
trimmer (DIFF) in the direction opposite of INC to set Deadband
minimum deadband. ( DIFF)
(2) Pressurize until unit switches ON, and obtain constant
DOWN
pressure. (Fig. A)
Power Supply, Couplings
●●Restrictor coupling
WK-20
Hex,19 across flats 21.
9 Rc1/4
WK-A-20
Hex,19 across flats 21.
9 Rc1/4
2 12
(24)
18
(18)
12
φ7.
40
34
Vent cock
16
16
13
13
R1/4 R1/4
WK-20 WK-A-20
Dimensions
ESP*–*(*)–*(*)–10 (Drip proof) Deadband adjustment trimmer Pressure setting trimmer
(w/rubber cap) (w/rubber cap)
Indicator LED Indicator LED
ET2
IFF
INC
UP
φ36
UP
UP
SE
SE
Indicator LED
4-core cable *
Outer diameter φ4.
1
L
Wire diameter 0.2 mm2
2000
UP
3-3
SE
67
30
16
O-ring
12
R1/4
(JIS B 2401 1B-P11)
G1/4
ESPF ESPP
φ39
3-core cable
Outer diameter φ6.
6
2000
Indicator LED
2000
Top cover
Cover removed by
unscrewing 4 screws.
Pressure setting trimmer inside.
100
11
81
Hex, 22 across flats
11
Hex, 22 across flats
30
16
12
O-ring R1/4
(JIS B 2401 1B-P11)
G1/4
ESPF ESPP
L
3-4