Professional Documents
Culture Documents
org/student_take_quiz_assignment/start/41346147
Home
End of quiz
You are at the end; press Finished to complete and grade the quiz.
You can review your answers below and click Edit if you want to change any.
Finished
Question 1
To determine the amount of moment that is distributed to each member at a node, we will calculate distribution
factors for each member connected to a given node.
Response: True
Question 2
For the frame below, the rotation at C is equal to:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 1/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Response: 136.18/EI
Question 3
For the frame below, the moment MBA is equal to:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 2/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Response: 135
Question 4
If a joint connects two members, then any bending momentfound at the joint first needs to be distributed between
the near ends of the members ..
Question 5
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 3/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Response: True
Question 6
For the beam loaded as shown, the value of the rotation, in radians, at the roller support is equal to:
Response: 6.17/EI
Question 7
Which of the following situations does not merit a modification in the stiffness factor?
Question 8
For the frame shown below, what will be the moment MBA?
Response: M/2
Question 9
For the beam loaded as shown, the FEM on the right side for the section containing the triangular load is
equal to:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 5/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Question 10
For the frame shown, how many number of unknowns must be solved before detemining the moments at the joints?
Response: 3
Question 11
For the frame shown, the vertical force at pt. C is equal to:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 6/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Response: 3M/4L
Question 12
Where the force method was good at analysing indeterminate structures with a low number of degrees of
indeterminacy, the slope-deflection method will be good for analysing highly-constrained structures, with a lot of
degrees of indeterminacy, and not much freedom of movement.
Response: True
Question 13
For the beam loaded as shown, the number of section/s considered is:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 7/8
11/24/23, 8:15 AM T-CEET311 CEE32 (1st Sem. 2023-2024 ) - https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147
Response: 2
Question 14
The stiffness of the members are measured in terms of the following:
Question 15
The iterative process of the moment distribution process includes 2 steps. These are:
https://dlsud.edu20.org/student_take_quiz_assignment/start/41346147# 8/8