Professional Documents
Culture Documents
S-722D 2020
Datasheet for
Flare Package
Revision history
Acknowledgements
This IOGP Specification was prepared by a Joint Industry Programme 33
Standardization of Equipment Specifications for Procurement organized
by IOGP with support by the World Economic Forum (WEF).
Disclaimer
Whilst every effort has been made to ensure the accuracy of the information
contained in this publication, neither IOGP nor any of its Members past present or
future warrants its accuracy or will, regardless of its or their negligence, assume
liability for any foreseeable or unforeseeable use made thereof, which liability is
hereby excluded. Consequently, such use is at the recipient’s own risk on the basis
that any use by the recipient constitutes agreement to the terms of this disclaimer.
The recipient is obliged to inform any subsequent recipient of such terms.
This publication is made available for information purposes and solely for the private
use of the user. IOGP will not directly or indirectly endorse, approve or accredit the
content of any course, event or otherwise where this publication will be reproduced.
Copyright notice
The contents of these pages are © International Association of Oil & Gas Producers.
Permission is given to reproduce this report in whole or in part provided (i)
that the copyright of IOGP and (ii) the sources are acknowledged. All other rights are
reserved. Any other use requires the prior written permission of IOGP.
These Terms and Conditions shall be governed by and construed in accordance
with the laws of England and Wales. Disputes arising here from shall be exclusively
subject to the jurisdiction of the courts of England and Wales.
Foreword
This specification was prepared under Joint Industry Programme 33 (JIP33) "Standardization of Equipment Specifications for
Procurement" organized by the International Oil & Gas Producers Association (IOGP) with the support from the World Economic
Forum (WEF). Companies from the IOGP membership participated in developing this specification to leverage and improve
industry level standardization globally in the oil and gas sector. The work has developed a minimized set of supplementary
requirements for procurement, with life cycle cost in mind, resulting in a common and jointly agreed specification, building on
recognized industry and international standards.
Recent trends in oil and gas projects have demonstrated substantial budget and schedule overruns. The Oil and Gas
Community within the World Economic Forum (WEF) has implemented a Capital Project Complexity (CPC) initiative which
seeks to drive a structural reduction in upstream project costs with a focus on industry-wide, non-competitive collaboration and
standardization. The CPC vision is to standardize specifications for global procurement for equipment and packages. JIP33
provides the oil and gas sector with the opportunity to move from internally to externally focused standardization initiatives and
provide step change benefits in the sector's capital projects performance.
This specification has been developed in consultation with a broad user and supplier base to realize benefits from
standardization and achieve significant project and schedule cost reductions.
The JIP33 work groups performed their activities in accordance with IOGP's Competition Law Guidelines (November 2014).
Introduction
The purpose of this equipment datasheet is to define buyer specific requirements for the procurement of flare packages in
accordance with IOGP S-722 for application in the petroleum and natural gas industries. The datasheet provides project specific
requirements where the supplementary specification and its parent standard require the purchaser to define an application
specific requirement. It also includes information required by the purchaser for technical evaluation purposes. Additional
purchaser supplied documents are also listed in the datasheets, to define scope and technical requirements for enquiry and
purchase of the equipment.
This datasheet shall be used in conjunction with the supplementary requirements specification IOGP S-722, information
requirements specification IOGP S-722L and quality requirements specification IOGP S-722Q which together comprise the full
set of specification documents. The Introduction section in the supplementary requirements specification provides further
information on the purpose of each of these documents and the order of precedence for their use.
27 4.2 g), 5.4.4 Sour service - for waste gas equipment and piping : Select Select
316 4.2 d), 4.2 Static inlet pressure : Input Data Select Select
317 4.2 c), 4.2 Maximum allowable exit velocity : Input Data Select Select
318 4.2 c), 4.2 Calculated peak exit velocity : Input Data Select Select
319 4.2 i) Wind speed for mechanical design : Input Data Select Select
320 4.6.2 p) Minimum flow for stable flame : Input Data Select Select
321 Radiation performance
322 4.3.2 Based on case : Select Select
323 4.2 f), 4.2 Peak radiation at grade : Input Data Select Select
324 4.2 f), 4.2 Wind speed for peak radiation : Input Data Select Select
325 4.2 f), 4.2 Distance to peak radiation : Input Data Select Select
326 4.2 f), 4.2 Distance to 6.31 kW/m² (2000 Btu/h-ft² ) : Input Data Select Select
327 4.2 f), 4.2 Distance to 4.73 kW/m² (1500 Btu/h-ft² ) : Input Data Select Select
328 4.2 f), 4.2 Distance to 3.15 kW/m² (1000 Btu/h-ft² ) : Input Data Select Select
329 4.2 f), 4.2 Distance to 1.58 kW/m² (500 Btu/h-ft² ) : Input Data Select Select
392 4.2 k), 4.5 a), 4.5 a) Upper section material : Input Data
393 Upper section diameter : Input Data Select Select
394 4.5 a) Upper section thickness : Input Data Select Select
395 Lower section length : Input Data Select Select
396 4.2 k), 4.5 a), 4.5 a) Lower section material : Input Data
397 Lower section diameter : Input Data Select Select
398 4.5 a) Lower section thickness : Input Data Select Select
399 5.3.1 Connection type : Select Select
400 5.3.1 a), 5.3.1 b) Inlet flange code / standard : Select Select
401 4.2 k), 5.4.2 Inlet flange material : Input Data
402 5.3.1 b) Inlet flange size : Input Data Select Select
403 5.3.1 b), 5.3.1 Inlet flange type : Select Select
404 5.3.1 b) Inlet flange rating : Input Data
405 Gasket type : Input Data
406 4.2 k) Gasket material : Input Data
407 4.5 a) Lining length : Input Data Select Select
408 4.2 k), 4.5 a) Lining material : Input Data
409 4.5 a) Lining thickness : Input Data Select Select
410 Muffler length : Input Data Select Select
411 Muffler diameter : Input Data Select Select
412 4.2 k) Muffler material : Input Data
413 4.5 a) Windshield type : Input Data
414 Windshield length : Input Data Select Select
415 4.2 k), 4.5 a) Windshield material : Input Data
416 4.5 a) Flame retention : Select Select
417 4.2 k) Flame retention material : Input Data
Bolting material for burner flange, piping flanges and
418 4.2 k), 4.5 a) Input Data
attachments to burner :
419 Steam assist equipment
420 4.5 b), 4.4 Primary steam : Select Select
421 4.2 k), 4.5 a) Primary steam material : Select Select
422 5.3.1 c), 5.3.1 Primary steam connection type : Select Select
423 5.3.1 c) Primary steam connection size : Input Data Select Select
424 4.5 b), 4.4 Secondary steam : Select Select
425 4.2 k), 4.5 a) Secondary steam material : Select Select
426 5.3.1 c), 5.3.1 Secondary steam connection type : Select Select
427 5.3.1 c) Secondary steam connection size : Input Data Select Select
428 4.5 b), 4.4 Tertiary steam : Select Select
429 4.2 k), 4.5 a) Tertiary steam material : Select Select
430 5.3.1 c), 5.3.1 Tertiary steam connection type : Select Select
431 5.3.1 c) Tertiary steam connection size : Input Data Select Select
432 Air assist equipment
433 4.2 k), 4.5 a) Air plenum material : Select Select
434 Air plenum length : Input Data Select Select
435 Air plenum diameter : Input Data Select Select
436 5.3.1 c), 5.3.1 Air plenum connection type : Select Select
437 5.3.1 c) Air plenum connection size : Input Data Select Select
438 Pilots
439 4.7 f), Table 1 Quantity : Input Data
440 4.7 c) Rating - each : Input Data Select Select
441 Gas pressure : Input Data Select Select
442 4.2 k), 4.7 j) Pilot material : Input Data
443 4.2 k), 4.7 g) Pilot tip material : Input Data
444 4.2 k) Inspirator material : Input Data
445 4.7 i) Gas orifice size : Input Data Select Select
446 4.7 i) Strainer at pilot - mesh/screen openings size : Input Data Select Select
466 4.7 o), 4.9 c), 4.9.1 a) Flame monitors quantity per pilot : Input Data
467 4.7 o), 4.9 c) Flame monitors quantity per flare : Input Data
468 4.9.1 f) Thermocouples length : Input Data Select Select
469 Ignition system
4.7 o), 4.8 f), 4.8 g),
470
4.8 i) Main ignition system type : Input Data
471 4.7 o), 4.8 h) Main ignition system - automatic or manual : Select Select
4.7 o), 4.8 f), 4.8 g),
472
4.8 i) Backup ignition system type : Input Data
473 4.7 o) Backup ignition system - automatic or manual : Select Select
474 4.8 l), 4.8.1 f), 4.9.2 e) Distance between ignition panel and stack : Input Data Select Select
496 4.2 h), 4.13.1, 4.13.2 Integral / separate from stack : Select Select
501 5.2 d), 4.13.2 Corrosion allowance : Input Data Select Select
502 4.13.1, 4.13.2 Seal depth : Input Data Select Select
503 4.13.1, 4.13.2 Maximum vacuum without adding liquid : Input Data Select Select
504 4.13.1, 4.13.2 Freeze protection type : Input Data
505 4.13.1, 4.13.2 Freeze protection connection - flange type / facing : Input Data
506 4.13.1, 4.13.2 Freeze protection - size : Input Data Select Select
507 4.13.1, 4.13.2 Freeze protection - rating : Input Data
508 4.13.1, 4.13.2 Instrument / valve requirements : Select Select
509 4.13.1, 4.13.2 Steam injection / steam panel : Select Select
4.13.1, 4.13.2, 5.6.1
510
d) Special requirements : Input Data
511 4.13.2 Flare gas inlet connection - flange type / facing : Input Data
512 4.13.2 Flare gas inlet connection - size : Input Data Select Select
513 4.13.2 Flare gas inlet connection - rating : Input Data
514 4.13.2 Flare gas outlet connection - type : Select Select
548
Purge conservation device (for elevated flares
only)
549 4.2 h) Type : Select Select
550 Outside diameter : Input Data Select Select
551 Overall length : Input Data Select Select
552 4.2 k), 4.5 a) Material : Input Data
553 4.6.1 a) Thickness : Input Data Select Select
554 5.3.1 b), 5.3.1 c) Inlet flange type / facing : Input Data
555 5.3.1 b), 5.3.1 c) Inlet size : Input Data Select Select
556 5.3.1 b), 5.3.1 c) Inlet rating : Input Data
557 5.3.1 b), 5.3.1 c) Outlet flange type / facing : Input Data
558 5.3.1 b), 5.3.1 c) Outlet size : Input Data Select Select
559 5.3.1 c) Outlet rating : Input Data
560 5.3.1 c) Drain flange type / facing : Input Data
561 5.3.1 c) Drain size : Input Data Select Select
562 5.3.1 c) Drain rating : Input Data
563 Loop seal depth : Input Data Select Select
567 5.1 d), 5.1 f), 4.6.1 d) Design pressure : Input Data Select Select
658 5.10.4, 5.7.4 Ladders & platforms - material / finish : Select Select
659 5.10.5 Ladders & platforms specification : Input Data
660 Aircraft warning system (for elevated flares only)
661 5.9.1 Quantity : Input Data
662 5.9.1 Location : Input Data
663 5.9.1 Colour : Select Select
664 5.9.1 Type : Select Select
665 5.9.2 Retractable : Select Select
666 5.9.1 Painting specification : Select Select
667 Retractable davit (for elevated flares only)
668 4.2 h) Retractable davit : Select Select
669 Retractable davit - safe working load (SWL) : Input Data Select Select
670 4.2 k) Retractable davit - material : Input Data
671 4.2 h) Manual or electric hoist : Select Select
672 Smoke suppression control
673 4.2 e), 4.2 g) Flare gas flow detector : Select Select
674 4.2 e), 4.2 g) Smoke detector : Select Select
675 4.2 e), 4.2 g) Control strategy : Select Select
676 Firebox equipment (for enclosed flares only)
677 Overall height : Input Data Select Select
678 Rectangular firebox - length : Input Data Select Select
679 Rectangular firebox - width : Input Data Select Select
680 Round firebox - diameter : Input Data Select Select
681 Polygonal firebox - number of sides : Input Data
682 Polygonal firebox - width : Input Data Select Select
683 Rectangular windfence - length : Input Data Select Select
684 Rectangular windfence - width : Input Data Select Select
685 Round windfence - diameter : Input Data Select Select
686 Polygonal windfence - number of sides : Input Data
687 Polygonal windfence - width : Input Data Select Select
6.1.3, 6.1.5, 6.1.6,
688
6.1.7 Refractory material : Input Data
689 6.1.3 Refractory material - thickness : Input Data Select Select
Issue
Row
Flare Package
2 Tag No. : Insert Tag Number
3 Service : Insert Service Description
4 PURCHASE ORDER SPECIFIC REQUIREMENTS
5 Delete this sheet if not required
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
This datasheet is set-up to be used in electronic format by both the purchaser/user and the supplier/manufacturer.
This datasheet provides reference back to the parent standard or the supplementary specification where relevant.
Default values (if applicable) have been set according to essential minimum requirements as an integral part of this
specification and should only be changed where specific justification can be provided.
The Supplement sheet is provided in an open format sheet for application of specific items not covered in the main part
of the datasheet. This sheet is not intended to modify requirements defined in the supplementary requirements
specification.
The datasheet includes a revision (issue) column on the right hand side for use by the purchaser/user. After the first
issue, for each subsequent revision of the datasheet that is issued to suppliers for enquiry or purchase, the
purchaser/user should use the issue column to denote that the data on a specific row has been updated since the
previous revision. This will enable the supplier to easily identify where changes have been made.
Legend Select Supplier/manufacturer completed, pick list of pre-defined values (may be pre-populated
with a default value).
Input data Supplier/manufacturer completed data entry.
Select Purchaser/user completed, pick list of pre-defined values (may be pre-populated with a
default value).
Input data Purchaser/user completed data entry.