Professional Documents
Culture Documents
NO0valok 702809-En - Low
NO0valok 702809-En - Low
INFORMATION
Straumann® Novaloc® Retentive System
for Hybrid Dentures
6. APPENDIX 19
6.1 Appendix A 19
6.2 Appendix B 21
‒ 6 retention strengths
‒ Matrix Housing available in titanium, or color-
neutral PEEK² for a more aesthetic outcome
7 7
1 Titanium Nitride
2 Polyether ether ketone
³ 1.5 to 6.5 mm for BLX - 1 to 6 mm for all other systems
⁴ 2.5 to 7.5 mm (6 abutment heights in total) for BLX - 2 to 6 mm (5 abutment heights in total) for all other systems
Note:
A uniform horizontal height of all Novaloc® Abut-
ments makes it easier for the patient to insert the
prosthesis.
1
Step 1
ѹ Place a Novaloc® Scanbody on each abutment and press down
firmly.
ѹ Ensure that the surface of the scanbody is clean, free of residue,
and is dry.
2
Step 2
ѹ Proceed with scanning following the software prompts and hard-
ware IFU.
ѹ When the scan is complete, the scanbody needs to be removed,
cleaned, and sterilized before it can be used on the next case.
3
Step 3
ѹ Process the optical scan and sent to the laboratory for the design
and manufacturing of the final overdenture.
ѹ The Novaloc® Scanbody creates a recess in the overdenture to al-
low for the matrix housing to be seated without any interference
with the surrounding overdenture acrylic.
Follow the direct technique for the processing of the Novaloc® Matrix Housings into the overdenture, described on page 6.
Note:
A digital master model can also be created using implant level scan
body and selecting Novaloc abutment.
Note:
The master model can also be created with an implant-level im-
pression.
Note:
For a chair-side polymerization of the Novaloc® Matrix
Housing use the Novaloc® Processing Spacer to create
the space needed.
3.2 NOVALOC® DEMOUNTING TOOL FOR MOUNTING INSERTS AND MODEL ANALOG
REPOSITION AID (FIG. 4)
Removing the Novaloc® Mounting Insert
1. Insert the toe of the Novaloc® Demounting Tool into the Novaloc® Mounting Insert (Fig. 5).
2. Tip the Novaloc® Demounting Tool to the opposite side of the foot-shaped end and remove the Novaloc® Mounting Insert
from the Novaloc® Matrix Housing (Fig. 6).
1 2 3
4 5 6
7 8 9
8
8
11 12 13
14 15 16
17 18 19
9
9
COMPONENTS
Novaloc® Retention Inserts
The Novaloc® matrix system allows for a prosthetic insertion of up to
+/- 20° divergence, meaning 40° between two Novaloc® Abutments.
Mounting Collar
The Mounting Collar blocks out the area surrounding the abutment,
preventing that resin or a bonding agent flows into the Matrix Hous-
ing and imbedding the abutment.
Mounting Insert
The Novaloc® Mounting Insert protects the interior of the Novaloc®
Matrix Housing and keeps it in place during processing. Further-
more, it also prevents any resin or bonding agents of entering into
the Novaloc® Matrix Housing during fixation.
Processing Spacer
The Novaloc® Processing Spacer is a placeholder for the Novaloc®
Matrix Housing. It is used for the model-cast, cast metal-reinforced
denture or if the Novaloc® Matrix Housing shall be polymerized into
the overdenture chair-side.
Scanbody
Scanbodies can be used intraorally or in a lab setting, saving time
and improving efficiency in the digital process by accurately captur-
ing the precise location of the NOVALOC® abutment.
10
062.4521 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 1.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4522 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 2.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4523 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 3.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4524 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 4.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4525 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 5.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4526 RB/WB Novaloc TiN ∅3.8 mm, 0°, GH 6.5 mm, TAV Titanium Gr 5/Titanium Nitride
022.0164 NC Novaloc® TiN ∅3.8 mm, 0°, GH 1 mm, TAV Titanium Gr 5/Titanium Nitride
022.0165 NC Novaloc® TiN ∅3.8 mm, 0°, GH 2 mm, TAV Titanium Gr 5/Titanium Nitride
022.0166 NC Novaloc® TiN ∅3.8 mm, 0°, GH 3 mm, TAV Titanium Gr 5/Titanium Nitride
022.0167 NC Novaloc® TiN ∅3.8 mm, 0°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
022.0168 NC Novaloc® TiN ∅3.8 mm, 0°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
022.0169 NC Novaloc® TiN ∅3.8 mm, 0°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
022.0170 RC Novaloc® TiN ∅3.8 mm, 0°, GH 1 mm, TAV Titanium Gr 5/Titanium Nitride
022.0171 RC Novaloc® TiN ∅3.8 mm, 0°, GH 2 mm, TAV Titanium Gr 5/Titanium Nitride
022.0172 RC Novaloc® TiN ∅3.8 mm, 0°, GH 3 mm, TAV Titanium Gr 5/Titanium Nitride
022.0173 RC Novaloc® TiN ∅3.8 mm, 0°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
022.0174 RC Novaloc® TiN ∅3.8 mm, 0°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
022.0175 RC Novaloc® TiN ∅3.8 mm, 0°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
* Manufacturer
Institut Straumann AG
Peter Merian-Weg 12, 4002 Basel
Switzerland
11
062.4527 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 2.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4528 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 3.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4529 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 4.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4530 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 5.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4531 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 6.5 mm, TAV Titanium Gr 5/Titanium Nitride
062.4532 RB/WB Novaloc TiN ∅3.8 mm, 15°, GH 7.5 mm, TAV Titanium Gr 5/Titanium Nitride
022.0176 NC Novaloc® TiN ∅3.8 mm,15°, GH 2 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0177 NC Novaloc® TiN ∅3.8 mm,15°, GH 3 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0178 NC Novaloc® TiN ∅3.8 mm,15°, GH 4 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0179 NC Novaloc® TiN ∅3.8 mm,15°, GH 5 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0180 NC Novaloc® TiN ∅3.8 mm,15°, GH 6 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0181 RC Novaloc® TiN ∅3.8 mm,15°, GH 2 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0182 RC Novaloc® TiN ∅3.8 mm,15°, GH 3 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0183 RC Novaloc® TiN ∅3.8 mm,15°, GH 4 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0184 RC Novaloc® TiN ∅3.8 mm,15°, GH 5 mm, A, TAV Titanium Gr 5/Titanium Nitride
022.0185 RC Novaloc® TiN ∅3.8 mm,15°, GH 6 mm, A, TAV Titanium Gr 5/Titanium Nitride
* Manufacturer
Institut Straumann AG
Peter Merian-Weg 12, 4002 Basel
Switzerland
12
022.0186 NC Novaloc® TiN ∅3.8 mm,15°, GH 2 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0187 NC Novaloc® TiN ∅3.8 mm,15°, GH 3 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0188 NC Novaloc® TiN ∅3.8 mm,15°, GH 4 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0189 NC Novaloc® TiN ∅3.8 mm,15°, GH 5 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0190 NC Novaloc® TiN ∅3.8 mm,15°, GH 6 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0191 RC Novaloc® TiN ∅3.8 mm,15°, GH 2 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0192 RC Novaloc® TiN ∅3.8 mm,15°, GH 3 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0193 RC Novaloc® TiN ∅3.8 mm,15°, GH 4 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0194 RC Novaloc® TiN ∅3.8 mm,15°, GH 5 mm, B, TAV Titanium Gr 5/Titanium Nitride
022.0195 RC Novaloc® TiN ∅3.8 mm,15°, GH 6 mm, B, TAV Titanium Gr 5/Titanium Nitride
* Manufacturer
Institut Straumann AG
Peter Merian-Weg 12, 4002 Basel
Switzerland
13
048.725 RN Novaloc® TiN ∅3.8 mm, 0°, GH 1 mm, TAV Titanium Gr 5/Titanium Nitride
048.726 RN Novaloc® TiN ∅3.8 mm, 0°, GH 2 mm, TAV Titanium Gr 5/Titanium Nitride
048.727 RN Novaloc® TiN ∅3.8 mm, 0°, GH 3 mm, TAV Titanium Gr 5/Titanium Nitride
048.728 RN Novaloc® TiN ∅3.8 mm, 0°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
048.729 RN Novaloc® TiN ∅3.8 mm, 0°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
048.730 RN Novaloc® TiN ∅3.8 mm, 0°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
048.731 WN Novaloc® TiN ∅3.8 mm, 0°, GH 1 mm, TAV Titanium Gr 5/Titanium Nitride
048.732 WN Novaloc® TiN ∅3.8 mm, 0°, GH 2 mm, AV Titanium Gr 5/Titanium Nitride
048.733 WN Novaloc® TiN ∅3.8 mm, 0°, GH 3, TAV Titanium Gr 5/Titanium Nitride
048.734 WN Novaloc® TiN ∅3.8 mm, 0°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
048.735 WN Novaloc® TiN ∅3.8 mm, 0°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
048.736 WN Novaloc® TiN ∅3.8 mm, 0°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
* Manufacturer
Institut Straumann AG
Peter Merian-Weg 12, 4002 Basel
Switzerland
14
048.747 RN Novaloc® TiN ∅3.8 mm, 15°, GH 2 mm, TAV Titanium Gr 5/Titanium Nitride
048.748 RN Novaloc® TiN ∅3.8 mm, 15°, GH 3 mm, TAV Titanium Gr 5/Titanium Nitride
048.749 RN Novaloc® TiN ∅3.8 mm, 15°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
048.750 RN Novaloc® TiN ∅3.8 mm, 15°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
048.751 RN Novaloc® TiN ∅3.8 mm, 15°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
048.752 WN Novaloc® TiN ∅3.8 mm, 15°, GH 2 mm, TAV Titanium Gr 5/Titanium Nitride
048.753 WN Novaloc® TiN ∅3.8 mm, 15°, GH 3,TAV Titanium Gr 5/Titanium Nitride
048.754 WN Novaloc® TiN ∅3.8 mm, 15°, GH 4 mm, TAV Titanium Gr 5/Titanium Nitride
048.755 WN Novaloc® TiN ∅3.8 mm, 15°, GH 5 mm, TAV Titanium Gr 5/Titanium Nitride
048.756 WN Novaloc® TiN ∅3.8 mm, 15°, GH 6 mm, TAV Titanium Gr 5/Titanium Nitride
* Manufacturer
Institut Straumann AG
Peter Merian-Weg 12, 4002 Basel
Switzerland
15
048.757V2 Novaloc® TiN ∅3.8 mm bar abutment M2, TAV Titanium Gr 5/Titanium Nitride
16
2010.601-NOV Retention Insert, white, light PEEK Light, approx. 750g 2 pcs
2010.611-NOV Retention Insert, white, light PEEK Light, approx. 750g 2 pcs
2010.710-NOV Novaloc® Retention Insert, red PEEK Extra-light, approx. 300g 4 pcs
2010.711-NOV Novaloc® Retention Insert, white PEEK Light, approx. 750g 4 pcs
2010.712-NOV Novaloc® Retention Insert, yellow PEEK Medium, approx. 1200g 4 pcs
2010.713-NOV Novaloc® Retention Insert, green PEEK Strong, approx. 1650g 4 pcs
Extra-strong, approx.
2010.714-NOV Novaloc® Retention Insert, blue PEEK 4 pcs
2100g
Ultra-strong, approx.
2010.715-NOV Novaloc® Retention Insert, black PEEK 4 pcs
2550g
17
2010.741-NOV Mounting and Demounting Tool for Retention Inserts (brown) Aluminum/steel 1 pcs
2.3
2010.701-NOV Matrix Housing, titanium (including Mounting Insert) Titanium / PEEK 4 pcs
∅ 5.5
2.3
2010.702-NOV Matrix Housing, PEEK (including Mounting Insert) PEEK 4 pcs
∅ 5.5
∅ 5.9
2.5
2010.722-NOV Forming/Fixing Matrix, red PEEK 4 pcs
* Manufacturer
Medentika GmbH
Hammweg 8-10, 76549 Hügelsheim, Germany
18
For an existing well-fitting and well-functioning lower complete denture, the Novaloc® Retentive System can be used in a
chair-side procedure.
Caution: It is a prerequisite however, that the lower complete denture does not need to be relined by a dental technician.
1 Place white Mounting Collars on each Novaloc® Abutment. The
Mounting Collars are used to block out the area surrounding the
abutments.
Then place a Matrix Housing with white Mounting Insert onto each
Novaloc® Abutment, leaving the white Mounting Collar beneath it.
19
6 Fill the hollowed area with self-curing PMMA resin to polymerize the
Matrix Housings in the denture.
8 Once the resin has cured, remove the lower complete denture from
the mouth and discard the white Novaloc® Mounting Collars.
Put the lower complete denture in hot, but not boiling, water. Place
it in a pressure pot when available.
20
6.2 APPENDIX B
6.2.1 Preparation for lab-side modification of an existing lower denture into an overdenture supported by Novaloc®
Abutments
If the lower complete denture’s fit is inadequate (poor adaptation to underlying tissue) after surgery and major adjustments
are necessary, indirect relining of the mandibular denture is necessary. This means that relining and insertion of Novaloc®
Matrix Housings incl. Mounting Inserts are performed by the dental technician immediately after border mold impres-
sion-taking. Lab-side relining has to be planned in advance with your dental technician.
11 Hollow out the existing denture base in the areas of the Novaloc®
Forming/Fixing Matrices with handpiece and resin bur.
21
16
17
22
Send the mandibular denture to the dental technician to reline it, in-
tegrate the Matrix Housings and convert it into an overdenture. Af-
ter having received the final overdenture from the dental technician
exchange the Mounting Inserts for the final Novaloc® Retention
Inserts and insert the final overdenture into the patient’s mouth. For
details see brochure Basic Information on the Straumann® Novaloc®
Retentive System for Hybrid Dentures (490.115).
23
International Headquarters
Institut Straumann AG
Peter Merian-Weg 12
CH-4002 Basel, Switzerland
Phone +41 (0)61 965 11 11
Fax +41 (0)61 965 11 01
www.straumann.com