ONSEW
CONSOLIDATED SEWING MACHINE CORP.
L__ INDUSTRIAL SEWING & CUTTING EQUIPMENT
INSTRUCTION MANUAL
339RB- 4
ONSEW
CONSOLIDATED SEWING MACHINE CORP.
L__ INDUSTRIAL SEWING & CUTTING EQUIPMENT
400 VETERANS BLVD, CARLSTADT, NJ 07072}
)
SUBRIOATION AND OLLING ADJUSTHENY
When starting the machine ini ti:
long time without using at all
hocessary parte before startin,
ally end after kept away for a
+ oil sufficiently to respective
@ operation ond pre-runing.
are pazTone on the following Fig.1,2 & } Indioute theae siling
LUBRIGATION TO ‘THE OLL
REYERVOLN IN THE ARM
AND OLLING ADJUSTMENT
fm
4
( ) (2)
Figs
1. Remove the of] stopper(1),
pour the o41 from the oft
hole(2) until the of] re-
ached to the top of the
oil gauge(3).
When operating the machine,
push down the adjusting
serrated nut(4) and turn it
coun ter~clockwise ax shown
Pig.d.
Whon not operating the ma-
chine, the oil adjusting
serrated nut(4) should
exactly ve returned back.
Pigs
Pull out the of2 gauge(1)
‘and pour the ofi fron this
hote(2) untia the oil. re-
eohed to the mark(3) as
jshown Fig.5.
oxniNa absusmMene 10 tHE HOOK
Loosen the serew(i), to in-
crease the oil flow, align
the reference
Line(2) on
the RAR(3) wi
the Nark(4), tol
stop the oil
flow, turn the
nut(3) 80 as to.
make the refor-|
ence 1ine(2)
vertioully,.}
}
1s Move up the needle bar(1),
2. Insert the needie(2) into
the needle bar ua far as
it will go with the long
groove Sof the needle
‘aces to the left, = |*
(in 2-needie, the long!
groove of the needles
faces inside each other.)
3+ Mehton the soren(4)
REMOVING AND INSERTING THE BOBBIN
WINDING. THE LOWER THREAD
ON THE BOBBIN
1. Open the lide plate(1), raise
the lutch(2) and remove’ the
bobbin( 3). 4
Insert the left wound threaded
bobbin into the bobbin case and
Push down-the lateh(2), +
Pess the bobbin thread through
into the alot(4) of sewing hook
tnd guide the threud batween
bobbin case opener(5) and the
top(6) of ening hook und draw
the thread end under the tension
spring(7). t
Pull owt a Terigth of the bobbin
thread 4~5om to the per of the
neadle plate(8) and oloeed’ the
needle plate keeping the olear—
anos fo ae to paas through the
Bobbin thready, LE
1. Insert the bobbin.into the bobbin
winder spindie(1).
Pull the set lever(2) to the lert
99 far, as jit nil). gov
Lead the “thread (aa Thiol
wind the thiedd on.
for several fines
shown by the
arrow direotiot ii Fig. 10,)
Winding operation showla ‘be done
on the condition of the thread
tightening: #
* Winding volume ‘can be adjusted
by the adjusting collar(4)TUREADLAG THE NOELLE wREAD
Raise up the needle, lead the thread as numerical order
from 1 to 11. (Pig. '11.@ 42). .
Thread needle
L-needle: from left to right.
2-needie: from inside to outeide.
REGULATING THE TREAD THNSLON
Needle thread
Meters "Tee Perfeot otitohing
{ Bobbin thread >
SRNR ----- tight tension of
q a meee thread
ee Figd3 ASRBE--~-. toove tension of
7 needle thread
1. ADJUSTING THE UPPER 2. ADJUSTING THE. LOWER
THREAD TENS1ON ‘THREAD TENSION
X QQ)
To adjust the
tenaton of the
upper thread,
turn the serr-
arated aut(1).
Figs Aye
To adjust the tension
of the lower thread,
turn the adjusting
screw(1).ADJUSTMENT OF THE PRESSURE
of ME PRESSER POOR hal
Peer
MEN OF NEN ALTBRH AINE
INU AMOUNT OF ‘NIE PRESD
} More 1 Leas
Pigsl6
To adjunt thin, turn tho fo mijust this) raine or Lower
adjusting serew(1) the wing nut(i).
ADJUSTHENT OF THE STITCH LENGTH AND THY REVERSE STITOHING
1. ADJUSTHRNT OF THE STUTOH LENGT
Turn the stitch regulating dial
(1), set the dasired number to
the’ stopper pin(2)..
* For ousy adjustment, lower the
raverse atitch Lever( 3) to the
medium position and then turn
the dinl(1). *
2. RRVENGE SELTOHING
Tena dom the reverue ubiteh
Lover(\} ua fur no £6 WLLL go.
7
ee rts
: 4 HOW 10 RE-SBP THE, SAPRTY CLUTCH mECHAH LSM
(2) 1. Remove the thread tangled in the
hook and dist, etc,
2. Pushing the button(1), turn the
machine pulley(2) slowly to the
opposite direction as shown Fig.
‘19, then the top.of the ‘but ton( 1)
15 otaght in the kot oft-the oon
und pulley rolatigg to became
hewvilye
3, Still turding the puliey(2), the
safety device is re-éngaged.
4. Then leave your finger from the
button(1).
FiggADTISTMERT OF THE REIGN OF THE REED HOG
(ay ‘
4 (Ly
: ae —— + w
The fend dog(1) must protrade Lta teeth
Lim from the needie plate surface(2)
when it hne come up to the highest
point of tts travel. (#ig.20)
To adjust thin: (Fig.21)
ie Turn the machine pulley in’ the norma.
direction to bring the feed dog to the
highest point.
2. boosen the screw(1).
3+ Move the feed dog up and down, und make the correct height.
4. Tighten the seren(1) securely,
SEPTING THE PEED DOG AND THE NEEDLE PosiTLoHING
2; Position of the feed dog against the needle plate.
a) @) 1. Seb the stitch Length at maximum,
(== 2. boonen the serewa(1) Fig.2} for
=f\n———— "the feed shart crank.
—I ch NL) 3. At the polmt of start and cintuh
: fond motton of the fead dog,
2, Lt mike equal olaarance of A&B
7 Wotwoen the not of the neadle
A eee plato(L) tig. 2? and the feed
br WE it dogla) Big.22.
= so rts (or v7
Fige22 Pi gees
4. lehten the scvewa(L) Fig.23
for the Feed shaft orenk.
2. the needle hole of the feed dog
and the neédie.
1s Lift up the feed dog.
2. Loosen the cotinesting screw(1) Fig.24
river hole(2) Fig.24
3+ Hold the lower part of the needie bar
le rook frame(1) #ig.25 ond set the needLe
Auto the needle hole of the feed dog.
4. Tighten the connecting serew(1) Pig.24,
securely.
Pige24TINING BEMMEEN CUE HBKDLE AND ROOK
2.0
With stitch length gt minimum and when the needle bar raised
2.6mm from its lowest point, the hook point should be at the
center of the needle.
At thie time, the measurement between the hook point and upper
end of the needle eye should be 2.2mm and the clearance tha =~
hook point(1) and the needle hollow(2) should be 0.02mn-0.1nm,
1 tajagting the timing (fig.28)
(1) Loosen the screwa(1)Fig.20 for
the gour(iarge) - :
(2) fo faster the hook timing again-
st the needle, move the gour(iar
ge)(2) to right, to slower, move
it to lett.
(3) After decision of the position,
tighten the screws(1) securely.
2 Adjusting the olaarunos
Loogen the sarew(3) for the tool
anddle and the clamp veraw( 4)
for the hook: audiLa.
(2) fo make the clencunce, move tha
hook waddie(5) to left or right
directiona.
(3) After decision of. the: position,
tighten the serew(3) and clamp
screm(4) securely.
3 fayagting the height of the needle(Fig.23)
(1) Loosen the gcrew(1) for the needle
var connecting stud slightly.
(2) Raise and lower the needle bar(2)
and then make the clearance.
(3) Atter dectaion of ‘the posi tio
tighten the sorew(1): for the
needle bar connecting stud.
£1g.29ADSUSTMENE OF THE BOMBIN CASE os tER
TL. onsen the serew(1) for opener
alightly. «
2. Tarn the mebine pulley unthl
the eponer(?) Ja Treated at bho
Curthent point from the needle
plate(s) during ita travel.
Jo Ab thiw poottinn, adjunt 16 10
that tho clearnnee between. the
Anglde edge of the opener(2)
and extreme point of the bobbin
case(4) is ubout 0.2m,
ALter adjustment, tlyhten the
qa) serew(1) "securely.
2
TIMING OF THE VIBRATING PREBEER Foot
‘This da the normal timing when turn
the machine pulley toward you, after
Jowerdng the preanar bar Lifter,
vibrating preoner foot should reach
the feed dog earlier than needle
point coman to, und when the needle
reigen, the vibrating preaser oot
should leave from ‘the feed dog after
the needle point has left from the
feed dog.
To adjust this:
1s Loosen the two screwa(i) for the
vibrating preaser Coot lifting
cam.
2, Adjust the ponttion of ite cam(2)
faater or slower an desired, and
then tiyhten the nerews(1).
ADJUSTMENT OF THR THREAD CORTWOLLER SPRING
: Hormnlly, the thread controller aprinalt)
should hold mack of the upper thread
until needle reachoa to the material
boing sewn, and it should pause while
tising of the needle and passing of
the upper thread through the bobbin
cuse.
1, Adjustuont of the control action of
the thread controller spring(1) ean
be done by the spring atop(2), after
Loosening the screw\3) for the spring
stop. :
+ Adjustment of the tension of the
thread controlier spring(1) oan be
dons by turning the tension control! er
stud(4), after loosening the sorew(5)
serrated nut(6).
* Alter devision of the position,
tighten the each screws and nut,5
j
FINE ADJUSTMENT OF THE URPER FEED
Ordinary, the feeding momentum of the lower feed aynchronizes
with that of the uppor feed. «
ify.when the momentum doas not synchronize, or inerensing or
decrensing that of the upper and noedie feed according to the
sewing conditions, the following adjustments are offered.
J. Loosen the nub(1).
2. Move the udjurting vollar(2) clone to the feed driving rock
ubalt() tor Lean Tood momentum, while mova uwny from “tha
Teed driving rook shaft(3) for more momentum.
3+ Meghten the nut(1) after deoioion of the position.
* Make sure that a ditch on the adjusting collar meota 6
ditch on the rock ohaft orank(4); ae standard of tho
setting position.
(ay GQ)