Professional Documents
Culture Documents
BLUETOOTH SYSTEMS
Page 1 of 20
INSTALLATION PROCEDURE
TOOLS REQUIRED
#2 Phillips Screwdriver
Cordless Drill
Driver Extension
1" Unibit
Safety Goggles
Marking Utensil
Measuring Scale
Scissors
Page 2 of 20
INSTALLATION PROCEDURE
ALL STYLES: 1. 2. Disconnect vehicle's negative (-) battery cable. Use small flat screwdriver to remove map lamp lens covers from overhead console.
Sunroof
Non-Sunroof
3.
Use #2 phillips screwdriver to remove (2) screws located behind lamp in overhead console. Remove (2) screws located in overhead console sunglass bin.
Page 3 of 20
INSTALLATION PROCEDURE
ALL STYLES: 4. 5. 5 Pull overhead console down to remove. Disconnect harness and set overhead console aside. 5
Non-Sunroof
a. Use #2 phillips screw driver to remove sun visor hook base. Repeat this step for both driver and passenger sides. b. Use plastic trim removal tool to remove screw cover for driver side visor. Use #2 phillips screw driver to remove driver side visor. a b b
Page 4 of 20
INSTALLATION PROCEDURE
ALL STYLES: c. Use plastic trim removal tool to loosen A-pillar trim at top end above driver side door. Pull with hands to remove A-pillar trim. c
d. Use plastic trim removal tool to remove side dash panel. e. Use #2 phillips screw driver to remove (2) screws from bottom of crash pad under cover. Disconnect the hood release cable and connectors from the cover. d e e
Page 5 of 20
INSTALLATION PROCEDURE
ALL STYLES: f. Use 10mm socket to remove (1) nut & (3) bolts from metal bracket. Use #2 phillips screw driver to remove (1) screw from dash at top of BCM. g. Use 10mm socket to remove (2) bolts on BCM. Move BCM down to gain access to wiring and plugs. f g g
Safety Goggles are recommended before moving on to step 7. 7. 7 Use plastic trim removal tool to remove sunglass bin door from overhead console. Dispose of spring and locking cam. 7
Page 6 of 20
INSTALLATION PROCEDURE
ALL STYLES: 8. Use measuring scale to identify center of harness hole location on back of overhead console. Mark center at 45mm (1 3/4") from left side of cavity and 20mm (3/4") from top of cavity. 9. 8 Lay overhead console face down on clean surface. Drill out 25mm (1") harness hole with 1" unibit. 8 20mm (3/4") 9
45mm (1 3/4")
10.
Drill Clip Holes a. Insert UIB-Door assembly into overhead console, making sure that both pivot pins are properly seated in holes in the overhead console. b. Use plastic trim removal tool to close sunglass bin door until door is pushed into the closed position. Rock the bin door up and down to create vertical marks with both clips. Continue to rock the door up and down 5 more times without opening the door to establish defined vertical contact lines.
Page 7 of 20
INSTALLATION PROCEDURE
ALL STYLES: Please skip to page 20 step 27 and cut out clip hole template before proceeding to step 10c. c. Remove UIB-Door assembly and locate two (2) vertical marks made by clips. Use clip hole template on page 20 to mark hole location center at 13mm (1/2") from top edge of cavity.
You must use protective tape on front of sunglass bin opening to prevent damage from drill. Do NOT allow drill bit to extend into the overhead console more than 3/16" as damage will occur to the electronics.
d. Drill pilot hole with 1/16" drill bit with hex head attached to driver extension. Drill depth stop can be marked on drill bit at 3/16" with tape from the cutting edge. Wrap tape around drill bit 10 times. Repeat for second hole. Use clip hole template to confirm hole location is accurate, 13mm (1/2") from top edge of cavity. c c c
Protective Tape
Page 8 of 20
INSTALLATION PROCEDURE
ALL STYLES: e. Use cordless drill and 7/32" drill bit with hex head attached to driver extension to cut full size hole. Drill from the back side. Repeat for second hole. e e e
11.
Insert UIB-Door assembly into overhead console, making sure that both pivot pins are properly seated in holes in the overhead console.
12. 11
Securely connect the wire harness to the module. Make sure connector locks in place with a positive click sound. 12
Page 9 of 20
INSTALLATION PROCEDURE
SUNROOF: 13. Peel backing from tape on module box and mount securely to headliner on passenger side. 13 13. NON-SUNROOF: Peel backing from tape on module box and mount securely to headliner on passenger side. 13
14.
Accessory Power Wiring Connections a. Cut black-shielded-yellow wire to length, approximately 200mm (8") long. Remove an additional 25mm (1") of shielding from end of black-shielded-yellow wire. a
14.
Accessory Power Wiring Connections a. Route black-shielded-yellow accessory wire through headliner and down A-pillar to BCM in dash area. b. Secure wire to factory harness retainer clips in A-pillar using tie straps. Keep wire clear from all side curtain airbag parts in A-Pillar. b
Page 10 of 20
INSTALLATION PROCEDURE
SUNROOF: b. Clip tape to expose 75mm of wire on the overhead console sunroof switch connector R22. b NON-SUNROOF: c. Wrap foam tape around black-shielded-yellow accessory wire and tuck above headliner at top of A-pillar. d. Remove 25mm (1") of shielding from the end of the black-shielded-yellow wire. c
c. Using Scotchlok #558 connect black-shielded-yellow accessory wire to pin 5 (pink wire) in sunroof switch white connector R22. c d
Accessory Power
Page 11 of 20
INSTALLATION PROCEDURE
SUNROOF: d. Wrap foam tape around Scotchlok #558. d NON-SUNROOF: e. Clip tape to expose 50mm of wires in black connector BCM-KM on back side of BCM. f. Use plastic trim removal tool to separate pin 1 (red/orange wire) from other wires in black connector wrap foam tape BCM-KM. f
15.
Constant Power & Ground Wiring Connections a. Cut red and black wires to length, approximately 200mm (8") long. This step will not be necessary if wires are precut.
Page 12 of 20
INSTALLATION PROCEDURE
SUNROOF: b. Using Scotchlok #558 connect red power wire to pin 2 (red wire) in overhead console lamp & sunroof switch connector R22. c. Using Scotchlok #558 connect black ground wire to pin 1 (black wire) in overhead console lamp & sunroof switch connector R22. g NON-SUNROOF: g. Using Scotchlok #558 connect black-shielded-yellow accessory wire pin 1 (red/orange wire) in the black connector BCM-KM.
BCM-KM Connector: Cigarette Lighter Circuit Power Ground Accessory Power b/c
Page 13 of 20
INSTALLATION PROCEDURE
SUNROOF: d. Wrap foam tape around Scotchlok #558. d 15. NON-SUNROOF: Constant Power & Ground Wiring Connections a. Cut red and black wires to length, approximately 200mm (8") long. This step will not be necessary if wires are precut. b. Clip tape to expose 50mm (2") of wires on the wrap foam tape a overhead console map lamp wire harness.
Page 14 of 20
INSTALLATION PROCEDURE
SUNROOF: 16. Routing Wires a. Secure ALL (3) excess wires with tie straps to main harness with tie strap. a NON-SUNROOF: c. Using Scotchlok #558 connect red power wire to pin 2 (red wire) in overhead console map lamp connector R22. d. Using Scotchlok #558 connect black ground wire to pin 1 (black wire) in overhead console map lamp connector R22. c/d
R22 Connector: Lamp & Sunroof Switch Circuit e. Wrap foam tape around Scotchlok #558. e wrap foam tape
Power
Ground
Page 15 of 20
INSTALLATION PROCEDURE
SUNROOF: b. Route main harness around opening and position remaining harness above headliner on driver side. b a 16. Routing Wires a. Secure red and black wires to main harness with tie strap. NON-SUNROOF:
b. Route main harness around opening and position remaining harness above headliner on driver side. b
Page 16 of 20
INSTALLATION PROCEDURE
ALL STYLES: 17. 18. 19. 18 Route white connector from main harness through 25mm (1") hole on back side of console. Plug white connector into UIB-Door assembly. Make sure white connector locks in place with a positive click sound. Reconnect negative (-) battery terminal.
20.
Turn the ignition to ON position. The operating buttons on the UIB assembly will illuminate. Allow 5 seconds for the system to self-check.
21.
Push the phone button to activate the system. The blue center bar will illuminate and "BlueConnect Ready" will be heard. BlueConnect is now ready for the pairing process and use.
21
Phone button
Page 17 of 20
INSTALLATION PROCEDURE
ALL STYLES: 22. Reconnect all wire harness connectors to back of overhead console. Push overhead console into opening and replace screws. Replace lens covers. 22 22 22
Sunroof 23.
Non-Sunroof
Use plastic trim removal tool to close sunglass bin door until clip locks into place. Ensure door is securely locked into place (drilled 7/32" holes).
23
Page 18 of 20
INSTALLATION PROCEDURE
ALL STYLES: 24. Reinstall in reverse order all remaining trim pieces removed during installation. Non sunroof: (1) bolt & (1) screw on BCM, (1) nut & (3) bolts on metal bracket, crash pad cover & (2) screws, hood release cable on crash pad cover, side dash panel, A-pillar trim, driver visor, driver and passenger sun visor hook bases. 25. 26. 25 Check function for all that apply: Map lamps, Dome Lamps, Mirror, Sunroof. Place the User Guide packet inside the vehicle glove compartment after installation.
Page 19 of 20
INSTALLATION PROCEDURE
ALL STYLES: 27.
27
27
Page 20 of 20