Professional Documents
Culture Documents
Civil Engineering Interview Questions
Civil Engineering Interview Questions
if only 1 slab of a floor get sagged, how could be it repaired? 2. if any footing
gives the cube result, after 28 days less than 16 n/mm2 in spite of 20 n/mm2
what are the remedies ?
Answer
# 2.if it is a big footing we cannot remove and redo. so remove the top 200mm concret
by chiping and use proper bonding agents and introduce few more rebars through the
colomn and anchor them to the old footing and change the shape of the footing to a
triangular shape with rebars and re concrete the top surface and additional care to be
taken at the time of casting plinth beam it is better to redesign the plinth beam to take
more load which the coloum will carry. Note. check the mix design and use skilled
manpower while casting cubes at site. also place them in water immediately after
removing from moulds (delay in this activity will also cause cube failure)
2 2 reasons for saging.1) bad staging/supports. 2) bad design. any hw if it sagged it does
noteffect the next slab casting we can cast the next one. as far as repairing of 1st slab is
consern we should have a graphical representation of sag and find out the lowest level
and highest level plot them and with the help of this date we can fix the floor level ilttle
elevated than planned and the sagged area should be concreted (screed concret) with
good mix as per site condition.
If on-site slump test fails, should engineers allow the contractor to continue
the concreting works?
The first school of thought is rather straightforward: the contractor fails to comply
with contractual requirements and therefore as per G. C. C. Clause 54 (2)(c) the
engineer could order suspension of the Works. Under the conditions of G. C. C.
Clause 54(2)(a) – (d), the contractor is not entitled to any claims of cost which is
the main concern for most engineers. This is the contractual power given to the
Engineer in case of any failure in tests required Engr. Salman Ali Syed Saudi
Electricity Company by the contract, even though some engineers argue that
slump tests are not as important as Other tests like compression test.
The second school of thought is to let the contractor to continue their concreting
works and Later on request the contractor to prove that the finished works comply
with other contractual requirements e.g. compression test. This is based upon the
belief that workability is mainly required to achieve design concrete compression
strength. In case the compression test also fails, the contractor should demolish
and reconstruct the works accordingly. In fact, this is a rather passive way of
treating construction works and is not recommended because of the following
reasons:
If on-site slump test fails, should engineers allow the contractor to continue
the concreting works?
Q: Describe yourself.
Q: Tell me about your educational background?
Q: What do you know about the organization?
Q: How would you do justice to the job?
Q: What are your weaknesses?
Q: What are your salary expectations for this job?
Q: What are the projects you have ever undertaken?
Q: What do you do in leisure?
Q: Do you want to ask anything from us?
Q: What are your hobbies?
Q: Why do you want to go into this field?
Q: Describe one of the technical problems you had to solve.
Q: How would you develop yourself in this type of Structural Engineer
role?
Q: Do you have any experience in developing technical specifications?
Q: What are the differences between vector and array?
Q: What experience have you had in writing technical materials?
Q: What is the thing you dislike the most in the world? Why?
Q: What does success mean to you?
Q: How do you define failure?
Q: How do you define arrogance? Are you arrogant?
Q: What role are you ready to take in a group?
Q: Who has been an inspiration for you?
Q: What is more important to you, money or success?
Q: What were some of your most important engineering achievements?
Q: Can you name some engineers that you knew or worked with?
Q: Can you describe how engineering generally has changed during your lifetime?
Q: Why do you want this job?
Q: Why do you want to work with this organization?
Q: Where do you see yourself five years down the line?
Q: What are your strengths?
Q: How do you pursue your hobbies?
Q: What has been your greatest achievement?
Q: What has been your greatest failure?
Q: How do you take challenges?
Q: Are you willing to work in shifts?
Q: What is the thing you like the most in the world? Why?
Q: What kind of person are you?
Q: Rate yourself on a scale of 10.
Q: Why did you choose _________ as your major/subjects?
Q: Are you willing to travel?
Q: Why are you leaving the organization you work for?
Q: How much time do you need to join the organization?
Q: Are you aggressive?
Q: What makes you a good manager?
Q: What motivates you the most?
Q: What skills and abilities do you have?
Q: Is there anything you want to ask?
Q: Design a four-input NAND gate using only two-input NAND
gates.
Q: What experience have you had in working with field forces?
Q: Tell us about your experience with computer-aided design
software.
Q: Where were your early contributions in your engineering work
— planning, design, construction, operation, writing, teaching,
and research?
General Questions for Civil Engineers
Q: According to you, what is the best design for building bridges?
Q: What are all the new civil construction materials and concepts?
Q: What is softsoil?
Q: Explain your project management?
Q: What are the CAD software versions you have used?
Q: What are some of the different ways to lay a foundation?
Q: Why is a manhole round?
Q: What is earth?
1. How to increase bearing capacity of soil?
2. What is the design mix of M5?
3. Define Orientation of building?
4. What causes cracks in a building? What is the lasting solution to stop the
cracks. the cracks show on the beam and block wall ?
5. What is the best book for building construction?
6. What is mean by super structure?
7. What is the differance between wind and earthquake spectrum?
8. what are all the new civil construction materials?what is the new concepts?
9. Do you have Structural design experience?
10. Demonstrated work experience with Interior Design and/or Architectural
Firms?
11. Are you comfortable with formal design concepts in the home furnishings
area? How did you reach your thesis design concept?
12. What is the best design for building bridges?
13. What is the minimum distance allowed between a building and a parking lot
area ? Does the size of the structure or lot size need to be taken into account?
can u use instead of water milk for concreting ?
U are a civil engineering student?why do u want to enter into IT industry
Why we do design mix of concrete when there is nominal method using the IS-Code
available ?
what is mix design?
why either no or minimum shear reinforcement is provided in case of slabs?
What is Suggested type of cement for concreting at water, for mass concreting and
where the chaces of gettin attucked by salt?
How many types of camber?
why we always preffer short column in case of residential building?
is there any advantages between the use of One way slab & two way slab?
What should be the % of steel for R. C. C. perpose based on volume &
area ?
In olden days reinforcing bars in concrete are not got rusted even till
now. But recently provided steel getting rusted in concrete. what are
the probable reasons?
how bridge design is to be start? what is the preliminary step for
design? which code of practice is to be used for design? what r the
methods used for design? what r the ivestigation r carried out? what r
the design criteria for design and loading conditions?
what is pile foundation?
how we can calculate the capacity of a proposed canal in a command
area. MPPSC-Madhya-Pradesh-Public-Service-Commission
What is Pavement & carrage way? NBCC
What will be compressive strength of bricks , Hollow blocks, Solid blocks HCL
What is the shelf life of a refractory used structures? in boiler furnace ? Monster
why you considers yourself suitable for the post of site engineer Ritspin-
Synthetics
what is silica fumes or micro silica? and whr is it used? wat r its advantages?
castigliano's theorems are based on Essar
What is swear, swage and storm water? 2)What are the sizes of bricks based on
Nominal, practical and standard? 3) What is the distinguies between the grade
of cement 43, 53? L&T
What is gauge and gage? L&T
How we decide the the load combinations for design of RCC
QUESTIONS
How to calculate the Water cement ratio of required compressive
Strength of concrete?
Are you comfortable with formal design concepts in the home
furnishings area?
Are you having any structural design experience?
What was your synopsis for thesis topic?
Explain your project management?
How to calculate the rating of air conditioner required in any area,
how to calculate the cfm required for any exhaust unit or air
washer unit.
why 1.25 factor is to be multiplied to cylindrical strength of
concrete while getting the equvalent cubical strength of concrete?
HOW TO FIND OUT THE QUANTITY OF STEEL FE415
HOW TO FIND OUT THE QUANTITY OF CONCREATE
what will be the weigth of 50 kg/sq cm and 30 kg/sq cm
compressive strength solid concrete block of 200 mm ?
QUESTIONS
1. I am in India. Employer A got approval for my H1. But they have no job for
me now. Company B is going to file H1 for me. They do not know about
company A. Is there any way that I get approved H1 of company A
transferred to Company B?
2. wat is six sigma course ? is it good for civil engineers . wat is pmp
certification ? is it good for civil engineers . 0 9
3. dialation means
What are the methods of measurement? Describe it shortly
how to preaper for interview wat they asked in interview give me idea
what is CBR Test
WHAT DO YOU MEAN BY MIX DESIGN OF CONCRETE?NAME THE
VARIOUS METHODS OF CONCRETE MIX DESIGN.EXPLAIN I.S.METHOD
OF MIX DESIGN
discuss the precautions to be taken during the various steps of manufacturing of
concrete
what is mix design civil engineering means abut
What is pile foundation?
how will calculate the lift load in high rise buildings
Civil engineering material testing Standard results
why do you desire to change from your current position?
what will be the weigth of 50 kg/sq cm and 30 kg/sq cm compressive strength
solid concrete block of 200 mm ?
What are the methods of measurement? Describe it shortly
In olden days reinforcing bars in concrete are not got rusted even till now. But recently provided
steel getting rusted in concrete. what are the probable reasons?
what are the criteria for choosing the span for the bridge (highway bridge)
How much do you want salary?
How many times one TMT bars bents & straight upto not broken the bar.HCC1
why 1.25 factor is to be multiplied to cylindrical strength of concrete while getting the equvalent
cubical strength of concrete? 1
what is Quality Reporting? 1
why there is curve at the end in channel sectinGNFC2
What is the capacity of Maharashtra in power generation by winds?MPSC1
How we decide the the load combinations for design of RCC structures? 3
Method of findingthe dry ingredient quantity of 1 m3 concrete.L&T4
How to increse bearing capacity in soils (Stabilisation of soils) 7
Why we do design mix of concrete when there is nominal method using the IS-Code available ?
Engineers-India4how we can calculate the capacity of a proposed canal in a command area.
How to increse bearing capacity in soils (Stabilisation of soils) 7
Did you handle any interior designing jobs? Shell2
How to defind P.C.C. mix design according ratio & IS coadITC-Infotech1
why you considers yourself suitable for the post of site engineerRitspin-Synthetics2
what is mean by super structure? 7
How many times one TMT bars bents & straight upto not broken the bar.HCC1
bridge design L&T2
HOw to find the depth of foundation? 2
What is meant by End contractions 1
What is plate load test? 1
what is meant by Stagging? 1
polavaram project is situated inwhich place? 2
what is Tsunami. explain it's formation.NHPC2
is the finess modulus of sand?
2you are a civil engineering student so what you have done to improve your
knowdgeInfosys1
Grades of concrete 2
what are all the new civil construction materials?
what are the new concepts ? 1
Is Sugar a retardar or accelator or plasctizer? 2
difference between high way pavement and local road?L&T5
how inovative you are?...how do u define innovation?Infosys4
how we can calculate the capacity of a proposed canal in a command area.MPPSC-
Madhya-Pradesh-Public-Service-Commission1
Grades of concrete 2
What is the finess modulus of sand? 2
How to calculate the rating of airconditioner required in any area,how to calculate the
cfm required for any exhaust unit or air washer unit. 2
In case of a beam ,main steel is provided along the longer span because, bending
moment is directly proportional to length but why in case of one way slab main steel is
provided along shorter span while as bending takes place along longer
span?commentPower-Grid2
Method of finding the dry ingredient quantity of 1 m3 concrete.L&T4
What is construction joint and expansion joint in CC pavements 3
How to defind P.C.C. mix design according ratio & IS coadITC-
Infotech1
What is plate load test? 1
when does sedimentation occur before filteration, along with it, along
with chlorination, after chlorination?NTPC2
which grade of concrete is the strongest? M20,M25,M30,M35 or
M40? 6
what is the projected employment outlook for this carrer? 1
what are IS code for M20, 25, etcL&T5
why either no or minimum shear reinforcement is provided in case of
slabs? 4
Do you expect there to be many jobs for civil engineers going into the
future? What are the three main drawbacks of being a civil engineer?
What are the three best things about being a Civil engineer? What
amount of vacation time is available to you? Is the time paid? What are
the usual hours of work required? Is it possible, or common, to work
from home? How much time do you spend on the site of your projects?
What type of schooling is required to be a civil engineer? How many
years are required to complete this education?
What is the finess modulus of sand? 2
Why we do design mix of concrete when there is nominal method using the
IS-Code available ?Engineers-India4
In case of a beam ,main steel is provided along the longer span because,
bending moment is directly proportional to length but why in case of one way
slab main steel is provided along shorter span while as bending takes place
along longer span?commentPower-Grid2
what are the criteria for choosing the span for the bridge (highway bridge) 2
Can we weld hot rolled steel ASTM A615 ? 1
Which IS code is saying the detail of deshuttering period? 2
Grades of concrete 2difference between high way pavement and local road?L&T5
bridge design L&T2
what is mix designPower-Grid1
In olden days reinforcing bars in concrete are not got rusted even till now. But
recently provided steel getting rusted in concrete. what are the probable
reasons? 4
What is meant by End contractions 1
appsc AEE'S interview questions wantedAPPSC3
What is the best design for building bridges? 4
What is plate load test? 1
What is the shelf life of a refractory used in boiler furnace ?Monster2
How to calculate the rating of airconditioner required in any area,how to
calculate the cfm required for any exhaust unit or air washer unit. 2
How to findout safe bearing capacity after stabilization of soil by method of the confinde method. 1
what is mix designPower-Grid1
What is plate load test? 1
appsc AEE'S interview questions wantedAPPSC3
what is pile foundation? 4
HOW TO FIND OUT THE QUANTITY OF CONCREATEBhel2
what is Quality Reporting? 1
In case of a beam ,main steel is provided along the longer span because, bending moment is directly proportional to
length but why in case of one way slab main steel is provided along shorter span while as bending takes place along
longer span?commentPower-Grid1
whatare the load combinations which are used for the foundation design in a tall structure ( 10 storied building)? 2
How to calculate the rating of airconditioner required in any area,how to calculate the cfm required for any exhaust
unit or air washer unit. 2
what is CBR TestHPCL1
how bridge design is to be start? what is the preliminary step for design? which code of practice is to be used for
design? what r the methods used for design? what r the ivestigation r carried out? what r the design criteria for
design and loading conditions? 1
Is Sugar a retardar or accelator or plasctizer?
2U are a civil engineering student?why do u want to enter into IT industryTCS4
How we decide the the load combinations for design of RCC structures? 3what is coping? 3
bridge design L&T2
how to calculate quantity of steel & concrete in stair case 2What is construction joint and expansion joint in CC
pavements 3
you are a civil engineering student so what you have done to improve your knowdgeInfosys1
What is plate load test? 1 how to calculate the steel for rcc slab? plz tell me the formula for
calculating the steel? 5 bridge design L&T 2 what is Tsunami. explain it's formation. NHPC 4 what
is coping? 5 Theemergency provisions of the constitution of india were greatly influenced by: a)the
government of india act,1935 b)the constitution of canada c)the weimer constitution of germany
d)the constitution of the united states APPSC 1 What is the difference between nominal mix and
design mix? 1 How do you determine or evaluate success? Essar 2 plz send me civil q papers of
hpcl Shell 2 what are all the new civil construction materials?what are the new concepts ? 1 how
bridge design is to be start? what is the preliminary step for design? which code of practice is to be
used for design? what r the methods used for design? what r the ivestigation r carried out? what r
the design criteria for design and loading conditions? 1 what is IS CODE in concrete tiles 1 why
you considers yourself suitable for the post of site engineer Ritspin-Synthetics 2 castigliano's
theorems are based on Essar 2 Which IS code is saying the detail of deshuttering period? 2 WHATS
THE DIFFERENCE BETWEEN UNIAXIAL COLUMN & BIAXIAL COLUMN GIVE
EXAMPLE? 1 why either no or minimum shear reinforcement is provided in case of slabs? 5 hi
frnds i hav got thro BHEL written exam..wat to prepare for intervw..guide me plz!!!!!!!!!!!!! Bhel 4
what is lifespan of an RCC structure? Why the RCC structures failing in quater of its life span? 3
what is Quality Reporting?
How to increse bearing capacity in soils (Stabilisation of soils) 8 what are IS code for M20, 25, etc L&T 16
Sir please Bhel Enigineer trainy test papaers in civil engineering Bhel 1 HOW TO FIND OUT THE
QUANTITY OF CONCREATE Bhel 5 1)What is Suggested type of cement for concreting at water, for
mass concreting and where the chaces of gettin attucked by salt? 2)How many types of camber? 3)why we
always preffer short column in case of residential building? 4) Is there any advantages between the use of
One way slab & two way slab? 5)What shoul be the % of steel for R. C. C. perpose based on volume & area
? Gammon 2 what is general scouring? 1 What is the shelf life of a refractory used in boiler furnace ?
Monster 2 How to get cinema chance? 4 what are the criteria for choosing the span for the bridge
(highway bridge) 2 In case of a beam ,main steel is provided along the longer span because, bending
moment is directly proportional to length but why in case of one way slab main steel is provided along
shorter span while as bending takes place along longer span?comment Power-Grid 3 What will be
compressive strength of bricks , Hollow blocks, Solid blocks HCL 3 List out the densities of different
construction materials such as brick, steel, sand, aggregate etc... 1 what is pile foundation? 10 What is the
finess modulus of sand? 2 which software better design in structure design or Rcc design(STAAD
PRO,TEKLA STRUCTURE) 2 1)What is swear, swage and storm water? 2)What are the sizes of bricks
based on Nominal, practical and standard? 3) What is the distinguies between the grade of cement 43, 53?
L&T 1 how bridge design is to be start? what is the preliminary step for design? which code of practice is to
be used for design? what r the methods used for design? what r the ivestigation r carried out? what r the
design criteria for design and loading conditions? 1 what u mean by shoring? 1 Theemergency provisions
of the constitution of india were greatly influenced by: a)the government of india act,1935 b)the
constitution of canada c)the weimer constitution of germany d)the constitution of the united states APPSC 1
What are the different types of pile founations used? 6
In case of a beam ,main steel is provided along the longer span because, bending moment is directly
proportional to length but why in case of one way slab main steel is provided along shorter span
while as bending takes place along longer span?comment Power-Grid 3 How to calculate the rating
of airconditioner required in any area,how to calculate the cfm required for any exhaust unit or air
washer unit. John-Crane 2 Did you handle any interior designing jobs? Shell 3 What is the best
design for building bridges? 5 Which IS code is saying the detail of deshuttering period? 2 how
many cement bag in 1m*m*m 10 what are all the new civil construction materials?what are the
new concepts ? 1 how inovative you are?...how do u define innovation? Infosys 4 what is mean by
super structure? 8 What is logic behind the use of Steel bar insted of gold bar? Rites 3 Can we
weld hot rolled steel ASTM A615 ? 2 what is SHEAR WALL ? why and where it is provided.
CGPSC 4 which software better design in structure design or Rcc design(STAAD PRO,TEKLA
STRUCTURE) 2 What is construction joint and expansion joint in CC pavements 4 Sir please
Bhel Enigineer trainy test papaers in civil engineering Bhel 1 U are a civil engineering student?why
do u want to enter into IT industry TCS 4 What is the shelf life of a refractory used in boiler furnace
? Monster 2 How much do you want salary? 5 how to calculate the steel for rcc slab? plz tell me
the formula for calculating the steel? 5 where we provide hinged joint in a framee structure ?
U are a civil engineering student?why do u want to enter into IT industry TCS 4What is the capacity of
Maharashtra in power generation by winds? MPSC 3 during earth quake base shear force=a/w*g Comment?
Power-Grid 2 HOW CAN DESIGN LENGTH,WIDTH AND HEIGHT THE FOUNDATION FOR THREE
FLOOR BUILDING? 1 Sir please Bhel Enigineer trainy test papaers in civil engineering Bhel 1 Method of
findingthe dry ingredient quantity of 1 m3 concrete. L&T 4 "Why you consider yourself suitable for the post"
Maytas 1 HOW TO FIND OUT THE QUANTITY OF CONCREATE Bhel 5What is the difference between
nominal mix and design mix? 1 In case of a beam ,main steel is provided along the longer span because, bending
moment is directly proportional to length but why in case of one way slab main steel is provided along shorter
span while as bending takes place along longer span?comment Power-Grid 3 what are the criteria for choosing the
span for the bridge (highway bridge) 2 How much do you want salary? 5 1)What is Suggested type of cement
for concreting at water, for mass concreting and where the chaces of gettin attucked by salt? 2)How many types of
camber? 3)why we always preffer short column in case of residential building? 4) Is there any advantages between
the use of One way slab & two way slab? 5)What shoul be the % of steel for R. C. C. perpose based on volume &
area ? Gammon 2 how to calculate quantity of steel & concrete in stair case 2What is softsoil? what kind of
foundation? 4 where we provide hinged joint in a framee structure ? 3WHAT IS THE DIFFERENCE
BETWEEN SINGLE REINFORCEMENT & DOUBLE REINFORCE, PLEASE DESCRIBE WITH NEAT
SKETCH. L&T 2 which grade of concrete is the strongest? M20,M25,M30,M35 or M40? 16 what is Tsunami.
explain it's formation. NHPC 4WHAT YOU MEAN BY PROOF STRESS?
whatare the load combinations which are used for the foundation design in a tall structure ( 10 storied
building)? 2 In olden days reinforcing bars in concrete are not got rusted even till now. But recently provided
steel getting rusted in concrete. what are the probable reasons? 4 civil engineering means abut Maytas 4 How we
decide the the load combinations for design of RCC structures? 4 Anyone have sample questions for bhel please
send me since Iam appearing for this exam. Kindly send this to my e-mail: nethaj_babu@yahoo.co.in Bhel 4
WHAT YOU MEAN BY PROOF STRESS? 1 what is Tsunami. explain it's formation. NHPC 4What is the best
design for building bridges? 5 what is IS CODE in concrete tiles 1 what is mean by super structure? 8 what is
meant by Stagging? 1 a simple instrument used for the measurement of colour in water is called 4 what are the
basic parameters considered in designing a pavement? 5 what u mean by shoring? 1 HOw to find the depth of
foundation? 3 how to calculate quantity of steel & concrete in stair case 2 In case of a beam ,main steel is
provided along the longer span because, bending moment is directly proportional to length but why in case of one
way slab main steel is provided along shorter span while as bending takes place along longer span?comment
Power-Grid 3Theemergency provisions of the constitution of india were greatly influenced by: a)the government
of india act,1935 b)the constitution of canada c)the weimer constitution of germany d)the constitution of the
united states APPSC 1 In case of a beam ,main steel is provided along the longer span because, bending moment is
directly proportional to length but why in case of one way slab main steel is provided along shorter span while as
bending takes place along longer span?comment Power-Grid 3What is construction joint and expansion joint in
CC pavements
What is logic behind the use of Steel bar insted of gold bar? Rites 3 what is pile foundation? 10
appsc AEE'S interview questions wanted APPSC 3 who much should be the lap length in
reinfocement L&T 3 1)What is swear, swage and storm water? 2)What are the sizes of bricks based
on Nominal, practical and standard? 3) What is the distinguies between the grade of cement 43, 53?
L&T 1 how inovative you are?...how do u define innovation? Infosys 4 What is pile foundation?
GMR 8 Did you handle any interior designing jobs? Shell 3 What will be compressive strength of
bricks , Hollow blocks, Solid blocks HCL 3 difference between high way pavement and local road?
L&T 7 HOw to find the depth of foundation? 3 what are the basic parameters considered in
designing a pavement? 5 List out the densities of different construction materials such as brick,
steel, sand, aggregate etc... 1 How to calculate the rating of airconditioner required in any
area,how to calculate the cfm required for any exhaust unit or air washer unit. John-Crane 2 what is
poissons ration of steel? 8 why there is need to provide shear reinforcement?give the basic reason?
Power-Grid 5 what is SHEAR WALL ? why and where it is provided. CGPSC 4 how to calculate the
steel for rcc slab? plz tell me the formula for calculating the steel? 5 What is the finess modulus of
sand? 2 what are the CAD software versions you have used?
what are IS code for M20, 25, etc L&T 16 Which IS code is saying the detail of deshuttering
period? 2 Sir please Bhel Enigineer trainy test papaers in civil engineering Bhel 1 what are the
CAD software versions you have used? 2 plz send me civil q papers of hpcl Shell 2 what will be the
weigth of 50 kg/sq cm and 30 kg/sq cm compressive strength solid concrete block of 200 mm ? 2
1)What is Suggested type of cement for concreting at water, for mass concreting and where the
chaces of gettin attucked by salt? 2)How many types of camber? 3)why we always preffer short
column in case of residential building? 4) Is there any advantages between the use of One way slab &
two way slab? 5)What shoul be the % of steel for R. C. C. perpose based on volume & area ?
Gammon 2 what is pile foundation? 10 what are the criteria for choosing the span for the bridge
(highway bridge) 2 how to calculate the steel for rcc slab? plz tell me the formula for calculating
the steel? 5 what u mean by shoring? 1 HOw to find the depth of foundation? 3 do aerocon
blocks give more or less equal strength than that of bricks...? L&T 2 the amount of gypsum
usuallyin the manufacture of cement 3 what are the basic parameters considered in designing a
pavement? 5 why 1.25 factor is to be multiplied to cylindrical strength of concrete while getting
the equvalent cubical strength of concrete? 3 What is logic behind the use of Steel bar insted of
gold bar? Rites 3 Can we weld hot rolled steel ASTM A615 ? 2 appsc AEE'S interview questions
wanted APPSC 3 Sir please send me the BHEL civil enginering trainee model Question papers. Bhel
2
how to increase bearing capacity of
soil?
1. The bearing capacity of soil is increased by cement and lime grouting method, in which cement or lime is add with the soil
which increase the bearing capacity of soil this is more commonly used in ROAD projects, this process is known as GROUTING
METHODER.
2. Bearing capacity of soils can be increased by compaction and grouting methods.
3. Another alternative way to increase bearing capacity of soil is, by using carbon nano tube (cnt), which is add to the soil. The
surface area of the cnt will stregthen the soil even if we use in small quantity.
4. yes, but ground improvement technics are adapted for location of site
5. A method for increasing the bearing capacity of foundation soils for built structures consisting of providing a plurality of holes
spaced from each other deep in the soil, and injecting into the soil, through the holes, a substance which expands as a
consequence of a chemical reaction, with a potential increase in volume of at least five times the volume of the substance before
expansion. The expansion of the substance injected into the soil produces compaction of the contiguous soil.
6. To improve the bearing capacity of soil, one of the following methods can be used.
1. Vibro Floatation Technique
2. Repalce the existing soil with road base materials and compact in layers to attain the required bearing capacity of soil.
3. Replace the existing soil with cement mix soil and compact in layers with water to attain the required bearing capacity.
4. Vibro Replacement Technique
Why we do design mix of concrete when there is nominal
method using the IS-Code available ?
to save an optimum content of cement, from 7.5 to 8 bags of cement to
6.6 bags of cement per CuM
to achieve economy and safety
To acheive best possible concrete with the ingredients available at
particular location design mix is used.
to ensure required |Target Mean Strength by controlling the parameters
of aggregate,sand and water accurately ....n also to design higher grade
of concrete ... ....incase of nominal mis method(say),M15 means 15mpa
comp.srength on 28 days using 1:2:4 proportions without considering
various conditions of conareting materials ...the same will be rectified in
design mix . simply nominal mix is blind technique where as design mix
is live n vibrant method of mix design in concrete technology to achieve
anticipated TMS.
what is the design mix of M5 m means the number of mix & 5 refers to the strength of
concrete block of size 150x150x150 mm after curing of 28days.
Important term in the question is "Design mix".
You see there is a term "Nominal mix" in concrete which is pertaining to certain standards and
thumbrules with respect to properties of concrete materials such as aggregate, sand, cement, water
and admixtures.
Â
However in order to get the most economic/workable mix of the concrete, it is designed and
tested in different proportions by having taken care of exact physical & chemical properties of the
ingredients.That is called the design mix of any grade of concrete.
Now normally M5 is used in PCC and hence design mix is not done for the same but for
grades M15 and above.
what is the design mix of M5 m means grade of concrete refers to the strength of concrete
block of size 150x150x150 mm after curing of 28days. which is called as M5 M=mega pascal =
N/mm2 or M5=5 N/mm2
What are the duties and responsibilities of a site engineer at the oil refinery
rehabilitation?
Latest Answer : first to check the site plan.and mention the site area then check
the soil bearing capacity.chek the site earth level.and prepare the level
chart.approved from consultant and take site order.start the earth work as
drawing.check total dimention and design. ...
How is the location of a structure on a site determined?
Latest Answer : The location of the structure depends on the geographical
factors such as soil, topography, and vegitation affects. Sencory factors, climate
factors, and codes and regulations also play a big roll in positioning the
structure. ...
Location on a site The location of the structure depends on the geographical
factors such as soil, topography, and vegitation affects. Sencory factors, climate
factors, and codes and regulations also play a big roll in positioning the
structure.
what is anchorage? Why anchoring of reinforcing bars necessary and what are the shapes ? 3 what
is poissons ration of steel? 8 Did you handle any interior designing jobs? Shell 3 how to calculate
the steel for rcc slab? plz tell me the formula for calculating the steel? 5 U are a civil engineering
student?why do u want to enter into IT industry TCS 4 how many cement bag in 1m*m*m 10
WHAT YOU MEAN BY PROOF STRESS? 1 what will be the weigth of 50 kg/sq cm and 30 kg/sq
cm compressive strength solid concrete block of 200 mm ? 2 What is the proportion of cement
agg. and sand for M20,M25 and M30? 2 WHAT IS THE DIFFERENCE BETWEEN SINGLE
REINFORCEMENT & DOUBLE REINFORCE, PLEASE DESCRIBE WITH NEAT SKETCH. L&T
2 Can we weld hot rolled steel ASTM A615 ? 2 Sir please Bhel Enigineer trainy test papaers in civil
engineering Bhel 1 How to defind P.C.C. mix design according ratio & IS coad ITC-Infotech 2 what
are all the new civil construction materials?what are the new concepts ? 1 What is logic behind the
use of Steel bar insted of gold bar? Rites 3 what is the projected employment outlook for this
carrer? 1 Can any one give me any link to download civil engineering code in free ? 1 What will
be compressive strength of bricks , Hollow blocks, Solid blocks HCL 3 how inovative you
are?...how do u define innovation? Infosys 4 what is CBR Test
In case of a beam ,main steel is provided along the longer span because,
bending moment is directly proportional to length but why in case of one way
slab main steel is provided along shorter span while as bending takes place
along longer span?comment
in beam the breadth is small so no need for
distributionreinforcement,but in slab load will not be distributed
like beam....
The primary load transfer direction will be in the shorter span and
as a result large negative bending moments will occur at these
supports. Therefore reinforcing steel is required to cross these
supports rather than the ones with less load transfer, which occur
in the supports with longer span.
The Bending moment in Oneway slab along shorter span is much
lesser than the longer span. It proportional to the square of the
span of the slab. Even we can have main steel along the longer span
but it leads to uneconomical.
what is anchorage? Why anchoring of reinforcing bars
necessary and what are the shapes ?
Anchoring of reinforcing bars is necessary when the
development length of the reinforcement is larger than the
structure. Anchorage is used so that the steel's intended
tension load can be reached and pop-outs will not occur.
Anchorage shapes can take the form of 180 or 90 degree
hooks.
Which IS code is saying the detail of deshuttering period? 2 what is IS CODE in concrete tiles 1 How to defind
P.C.C. mix design according ratio & IS coad ITC-Infotech 2 In olden days reinforcing bars in concrete are not got
rusted even till now. But recently provided steel getting rusted in concrete. what are the probable reasons? 4
what will be the weigth of 50 kg/sq cm and 30 kg/sq cm compressive strength solid concrete block of 200 mm
? 2 why reinforcement is not provided at centre for beams r column 4 whatare the load combinations which are
used for the foundation design in a tall structure ( 10 storied building)? 2 what are the criteria for choosing the
span for the bridge (highway bridge) 2What is Pavement & carrage way? NBCC 1 why there is need to provide
shear reinforcement?give the basic reason? Power-Grid 5 wat happens to the foundation when only live & dead
loads are considered( wind load is excluded) during the design of tall structures. options are: a)only settlement in
the internal structure and not external structure b)only settlement in the external structure and not internal
structure c)no differential settlement d)none of the above IOCL 3 In case of a beam ,main steel is provided along
the longer span because, bending moment is directly proportional to length but why in case of one way slab main
steel is provided along shorter span while as bending takes place along longer span?comment Power-Grid 3 Sir
please Bhel Enigineer trainy test papaers in civil engineering Bhel 1 Did you handle any interior designing jobs?
Shell 3 what are all the new civil construction materials?what are the new concepts ? 1 How to get cinema
chance? 4What is gauge and gage? L&T 1 what are the basic parameters considered in designing a pavement? 5
what are the CAD software versions you have used? 2 Can any one give me any link to download civil
engineering code in free ?
Define Orientation of building?
The main diffrence are for the highway pavement more width of road provided than local road ,
thickness of road is also more than local road, all the cautionary ,mandatory &informatery signs
available in highway road comparing with local road & fund providing agencies to highway are sate{
P.W.D.}& central govt in case of local road like Z.P.& Gram Panchayat
raiding surface
for higway pavements the design is done based on the IRC recommendations and all the geometric
requirements are maintained.it is rigid pavement. all laboratory based tests were carried out for the
design of pavement. in case of local soil there no requirement of carring laboratory based tests. it is a
flexible pavement.
high way pavement connects states where as local road connects local area.
highway pavements are made to bear high speed rolling loads while street roads are made for light
loads.
what is poissons ration of steel?
0.27 to .33
Poisson ratio is the ratio of the longitudinal strain to the
lateral strain. For steel it's value is 0.3.
what is mix design ?
How to findout safe bearing capacity after stabilization of soil by
method of the confinde method.
plate load test
How do you determine or evaluate success?
I determine my success through my Achievements and my
evaluate for my determination to do the goal.
Success is a continuous & everlasting journey which does not
have a destination, so i feel we can ever evaluate or
determine it at a certain stage in our life.
what is coping?
Coping in civil engg. constuction is the part of structure/Masonarywall which is
constructed on top of Wingwalls,Returnwalls,Boundary walls etc to protect the
masonary aswell to drain off the rain water&improves aesthtics of the
structure/wall.
Laying of concrete top of the wall to avoid the entry of rain water in structure
or wall
What is the differance between Load
and Force?
Load = mass x gravtational acceleration i.e g
Force = m x a