Professional Documents
Culture Documents
Operation Guide Network Video Recording
Operation Guide Network Video Recording
Operation Guide
2
Conncetion
NVR Installation
1. Gunakan brackets untuk pemasangan di rak.
2. Pastikan cukup space untuk kabel audio dan video.
3. Menghubungkan kabel rs-485.
4. Memberi setidaknya 2cm (≈0.75-inci) ruang antara rak mount perangkat.
5. Pastikan nvr di grounded
6. Suhu harus dalam kisaran-10 ºc ~ 55 ºc, 14ºf ~ 131ºf.
7. Kelembaban harus berada dalam kisaran 10% ~ 90%.
Steps:
1. Lepaskan penutup NVR pada panel belakang dan samping.
3
2. Sambungkan salah satu kabel ke motherboard NVR dan ujung lainnya ke HDD.
Pengaturan IP NVR
Anda dapat menggunakan pengaturan network di bagian menu Configuration – Network
Pada bagian informasi network, anda dapat melihat pengaturan MAC Address, IP Address dan
network mask. Pada bagian tersebut dapat dilakukan pengaturan IP address disesuaikan dengan kebutuhan
network yang terhubung dengan NVR.
General Enable
DHCP
With DHCP
enabled, the
router will
assign an IP
address to
the NVR
Select NIC
Type
Please Note:
After
enabling
DHCP,
The IP
REFRESH
configuration
becomes
“Greyed out”
IP CONFIGURATION
Please note that the NVR’s default IP Address is set to 192.0.0.64
5
Step 1.
Enable DHCP (check the checkbox). Press “APPLY” and then press “REFRESH”
Step 2.
After pressing refresh, the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway will have
new values.
Step 3.
Disable DHCP (uncheck the checkbox)
Step 4.
Change the value of “PREFFERED DNS SERVER” to 8.8.8.8 (“ALTERNATE DNS SERVER” can
be left blank).
The “MORE SETTINGS” tab contains the ports that need to be forwarded for remote access
The SERVER PORT is responsible for the MOBILE APP and CLIENT SOFTWARE log-in.
The HTTP PORT is responsible for WEB BROWSER log-in.
The RTSP PORT is responsible for VIDEO/AUDIO STREAMING.
The HTTP PORT and the SERVER PORT can be changed if desired, in order to avoid conflicts with
the ISP or the existing network configuration
7
Port Forwarding
After assigning the IP information to the NVR, connect a computer to the same router that the NVR
is connected to (wired connection is recommended, to avoid complications). Log into the
ROUTER, and proceed with PORT FORWARDING.
For PORT FORWARDING assistance contact the Internet Service Provider (ISP), or the
router manufacturer. Also refer to www.portforward.com for port forwarding step by step
instructions.
Please be aware, that Hikvision USA is not associated with www.portforward.com, and not
responsible for any activity between the user and www.portforward.com. Please refrain from
downloading any software from the abovementioned website.
Proceed to the “ROUTERS” section for step by step instructions.
DDNS SETUP
DDNS registration has been made more user friendly, and takes only a few seconds to
complete. The legacy units require user registration on www.hik-online.com. This step is no
longer needed.
Click on the
DDNS tab
After the changes have been made, presses “APPLY”. A “SUCCESS” message will pop up
If the Domain Name does not meet the acceptable criteria, and/or is already registered, an error message
will appear(The domain name cannot contain upper case characters, begin with a number, spaces,
special characters…).
9
Camera Administration
Menambahkan Camera
Setelah ip camera dan NVR terhubung dalam jaringan, hal ini memungkinkan ipcamera tersebut untuk
ditambahkan pada NVR. Terdapat dua cara untuk menambahkan perangkat camera pada NVR yaitu dengan
menggunakan discover dan penambahan secara manual.
Press “EDIT”
Press “+” to add the to change the camera’s IP
camera to the NVR address.
Recording Setup
Salah satu fungsi utamaa dari NVR adalah merekan video dan mentransmisikannya pada penyimpanan data.
Proses perekaman dapat diatur berdasarkan pengaturan schedule atau event yang masuk pada system.
Recording Modes
Secara default, mode rekaman belum di definisikan. Mode perekaman yang dapat digunakan adalah mode
countinues ( terus-menerus) atau berdasarkan event yang masuk pada system NVR.
Stream
Beberapa camera yang tergolong pada jenis ONVIF telah support dengan pengaturan stream secara langsung pada
NVR. Pengaturan stream digunakan untuk menentukan type codec, ukuran resolusi dan jumlah fps pada camera dengan
profiling setiap stream berbeda beda bergantung pada kebutuhan.
Select
Main
Stream
Record
Quality
Select
Camera
Record
Quality
Event
Sebagai tambahan mode perekaman, NVR dapat juga merekam video berdasarkan event. Potensi event yang mana dapat
di deteksi oleh NVR adalah Trigger by Motion Detection ( ketika objek bergerak di depan camera), Trigger by input
(digital camera input aktif, camera mulai merekam) dan Trigger by camera tamper ( ketika camera defocus, lensa
camera ditutup oleh sebuah objek sehingga penglihatan camera tertutup). Sesitifitas pendeteksi gerakan diatur langsung
pada web camera.
1. “MENU”>”RECORDING CONFIGURATION”
2. Click on the “EVENT” under the calendar (yellow). After this the mouse cursor will change to a
WAND.
3. Select the calendar, and it will turn YELLOW (just like on a computer, click on the
top-left corner of the calendar and drag to the bottom-right corner).
4. Press APPLY.
After the recording has been set to “EVENT RECORDING” go to “MOTION DETECT” to
set the motion detection for every camera. In this step, the IP cameras need to be configured
individually.
Motion Detection
Setup
Motion Area The
grid indicates the
Motion Sensitivity area, where
The amount of bright motion will be
green squares detected
indicates the
sensitivity level. (in
this picture the
sensitivity is set to 3)
15
Playback
To initiate a PLAYBACK, go to “MENU”>”PLAYBACK”.
Select a camera
to playback “Full Screen”
button. Going to
a full screen will
Select the allow
desired date to multiple channel
playback playback
Select the
desired time of Press PLAY to
playback begin playback
Click on the
timeline to select
the desired time
of playback
www.hikvision.com/en/us
16
BACKUP
Export Clips
Select the Select the
“START TIME” “END TIME”
After pressing “CLIPS EXPORT” a new window opens up containing all saved clips.
www.hikvision.com/en/us
18
Cofiguring App
All Hikvision DVRs, NVRs and IP Cameras can be accessed with iVMS-4500 application. The
APP can be downloaded from the APP STORE (iPhone/iPad), PLAYSTORE (Android). The
app is also available for WINDOWS MOBILE devices (Nokia Phones and tablets).
Download the app from the appropriate place and launch it. When the APP is launched for the first
time, a tutorial screen will be displayed, and it can be easily skipped.
Please Note:
If free HikVision
DDNS is
configured for the
device, change
the “REGISTER
MODE” to
20
Please Note:
CHANGE THE MODE ENTER “DEVICE DOMAIN” COMPLETE THE PAGE Alias is just a
friendly name for
the address book
(i.e. Home/Office)
“SAVE” BUTTON
Please note:
“START LIVE
VIEW” button
will begin live
camera stream
21
User Konfiguration
Jika NVR digunakan lebih dari satu user, maka sebaiknya membuat masing masing
priviledgeuser demi keamanan system NVR.
Adding a User
Steps:
1. Enter the User Management interface.
Menu >Configuration>User
3. Enter the information for new user, including User Name, Admin Password, Password, Confirm, Level
22
4. Click the OK button to save the settings and go back to the User Management interface. The added new user
will be displayed on the list, as shown in Figure 15. 8.
5. Select the user from the list and then click the button to enter the Permission settings interface, as shown
in Figure 15. 9.
Editing a User
For the added user accounts, you can edit the parameters.
Steps:
1. Enter the User Management interface. Menu >Configuration>User
2. Select the user to be edited from the list, as shown in Figure 15. 10.
3. Click the icon to enter the Edit User interface, as shown in Figure 15.11.