Professional Documents
Culture Documents
1
Compressors
The course topics should include topics such as:
Introduction to compressors;
Basic principles of operation;
General description and key components;
Types of compressors at Mopco;
Anti-surge protection;
Sealing systems;
Lube oil systems; and
Interstage cooling.
2
Introduction to
compressors
3
A compressor is defined as a الضاغط هى ألة تستخدم لزيادة
machine that causes a ضغط الغاز وتقليل حجمه
reduction in Volume and an
increase in the pressure of a ويستخدم الضاغط لتحريك الغاز
gas. خالل النظام عن طريق الطاقة
A compressor moves a gas وزيادة كثافة الغاز
through a process system by يتشابه عمل المضخة مع عمل
increasing the energy and
the density of the gas. الضاغط ولكن الضاغط يستخدم
The action of a compressor مع الغازات والمضخة تستخدم مع
is similar to a pump, a السوائل
compressor can be
considered as a gas pump.
4
Or a compressor pumping ويعتمد الزيادة فى الضغط
compressible fluid while
pump used pumping على تصميم وحجم الضاغط
incompressible fluid, one of ونظرا ألن الغاز يكون قابل
the most important effects of
an increase in gas energy is لألنضغاط فأن حجم الغاز يقل
pressure. مع زيادة الضغط وترتفع
The amount of pressure درجة حرارته
increase above the pressure
of the incoming gas depends
on the design and size of the
compressor that is used.
Because gas is compressible,
its volume will decrease as
its energy is increased.
5
Centrifugal compressor
Centrifugal compressor
Reciprocating compressor
Screw compressor
6
ضاغط طارد مركزى
Centrifugal Compressor
7
ضواغط الترددية
Reciprocating Compressors
8
Dry Screw Compressor
9
Basic principles of
operation
10
The purpose of gas الهدف من أنضغاط الغاز هو زيادة
compression is simply to الضغط من مستوى الى أخر أعلى
increase the pressure of a
gas from one level to وتعتمد زيادة الضغط على التطبيق
another. فتترواح من بضع مئات الى أالف
Depending on the process, الكيلوباسكال
this pressure increase may
range from several hundred
kPa to several thousands of
kPa.
11
The type, construction ويعتمد تركيب الضاغط
and operation of the وتشغيله على عدة عوامل
compressor will vary منها الضغط ومعدل السريان
depending on several
factors including ونوع الغاز
pressure, flow rate and ويوجد عدة طرق لضغط
type of gas. الغاز تعتمد على التطبيق منها
There are two principle ضاغط الطارد المركزى
methods used to والضاغط الترددى
compress gases for
process applications
reciprocating and
centrifugal compressors
12
ضواغط الترددية
Reciprocating Compressors
Reciprocating ويستخدم الضواغط الترددية
compressors use المكابس واألسطوانات
pistons, cylinders, and
والمحابس لحجز الغاز داخل
valves to trap a volume
of gas in a cylinder, األسطوانة وضغط الغاز عن
compress it by the طريق حركة المكبس ثم
positive action of a خروجه عند ضغط عالى عن
piston and then طريق فتح صمام الخروج
discharge it at this
higher pressure by
opening a valve.
13
ضواغط الترددية
Reciprocating Compressors
The process is وهذه العملية تشبه ما يحدث
14
ضواغط الترددية
Reciprocating Compressors
15
ضواغط الترددية
Reciprocating Compressors
16
ضاغط طارد مركزى
Centrifugal Compressor
A centrifugal compressor الضواغط الطاردة المركزية ترفع
increases gas pressure by الضغط عن طريق زيادة سرعة
first accelerating the gas and
then converting the المائع ثم بعد ذلك تحول هذه
increased velocity energy of السرعة الى ضغط
the gas into pressure. وهذا يتم عن طريق سحب الغاز
This is done by drawing the الى منتصف المروحة وتعجيله عن
gas into the center of the طريق مالمسته لريش المروحة
rotor and accelerated it by
contact with the rotating والتى تدور عن طريق محرك
blades called the impeller, كهربى أو محرك حرارى
which is driven, by a motor
or turbine (i.e. the gas is
flung off the impeller blades
to the wall of the casing).
17
ضاغط طارد مركزى
Centrifugal Compressor
This centrifugal action adds والقوىالطاردة المركزية تضيف
kinetic energy to the gas طاقة حركة للغاز والتى تتحول
(i.e. the gas molecules are
now moving at a much بالتالى الى ضغط عن طريق
higher speed). الناشر
This kinetic energy is وعن طريق تكرار هذه األفعال
converted to pressure as the أكثر من مرة يرتفع الضغط
gas moves to the discharge بصورة أكبر ويسمى هذا النوع من
side through a stationary
passage of increasing cross- الضواغط متعدد المراحل
section called the diffuser.
By doing this more then
once (i.e. multi-stages) high
discharge pressure can be
achieved
18
مقطع فى ضاغط طارد مركزى
Cross Section Of Centrifugal
Compressor
19
الضواغط الحلزونية
Screw Compressors
The rotary screw compressor is a الضاغط الحلزونى من النوع ذات
positive displacement compressor, األزاحة الموجبة ويتكون من عضوين
made of two intermeshing helical
rotors contained in the housing. دواريين
The driving rotor is usually made of يتكون العضو الدوار القائد من أربع ريش
four lobes and the driven rotor بينما يتكون العضو الوار المقاد من ست
usually consists of six lobes. ريش
As the helical rotor grooves pass
over the suction port they are filled وتسمح تجاويف العضو الدوار بكشف
with gas. فتحة دخول الغاز مما يؤدى الى امتأل
As the rotors turn, the grooves are الضاغط بالغاز
closed by the housing walls, forming
a compression chamber. to provide ويؤدى دوران العضو الدوار الى غلق
lubrication, sealing, cooling and فتحة الدخول مما يؤدى الى زيادة الضغط
avoid any metal to metal contact, كما يلزم تزييت وتبريد الحرارة الناتجة
lubricant is injected into the من أحتكاك العضويين الدواريين عن
compression chamber. .
طريق ضخ زيت بين العضوين الدوارين
20
الضواغط الحلزونية
Screw Compressors
Screw Compressors
21
الضواغط الحلزونية
Screw Compressors
22
الضواغط الحلزونية
Screw Compressors
As the rotors mesh, the عند تداخل العضوان الدوران
compression chamber
volume decreases, يقل حجم الغاز ويرتفع ضغط
compressing the خليط الغاز مع الزيت الى أن
gas/lubricant mixture toward
the discharge port where it
يخرج من فتحة الخروج
exits as the chamber passes ويستخدم فى أغلب أنواع
over the port.
Most manufacturers build a
الضواغط الحلزونية محبس
slide stop valve into the منزلق للتحكم فى كمية الغاز
casing that can be actuated المنضغط ويعمل يدويا أو عن
either manually or with an
air or hydraulic piston. طريق التحكم الهيدروليكى
23
الضواغط الحلزونية
Screw Compressors
24
الضواغط الحلزونية
Screw Compressors
The helical-lobe وتصنف الضواغط الحلزونية
compressor is further الى ضواغط جافة (ال تستخدم
divided into a dry and a زيت بين العضوين
flooded form.
الدورايين) وضواغط تستخدم
The capacity range for
the dry configuration is زيت
approximately 500 to ويترواح معدل السريان
35,000 cfm. للضواغط الجافة من 500
الى 35000قدم مكعبة
لكل
دقيقة
25
مكونات وأجزاء الضاغط الطارد المركزى
Components of Centrifugal
Compressor
CASING الجسم
The casing and cover وهو الجسم الذي يحتوي على أجزاء
include the inlet and الضاغط ويوجد به فتحات السحب
discharge connections. والطرد وبالجسم تجويفات لمرور
Shaft الهواء أو الغاز خاللها من مرحلة إلى
أخرى أو إلى خط الطرد .
The Rotor is normally
coupled to the driver by العمود : SHAFT
26
مكونات وأجزاء الضاغط الطارد المركزى
Components of Centrifugal
Compressor
DIFFUSER الناشر : DIFFUSER
27
مكونات وأجزاء الضاغط الطارد المركزى
Components of Centrifugal
Compressor
IMPELLERS : IMPELLERS المراوح
28
أنواع المراوح
Impeller Types
29
مكونات وأجزاء الضاغط الطارد المركزى
Components of Centrifugal
Compressor
BEARING : BEARING كراسي التحميل
Bearing support system consists غالبا ً ما تكون جلب وهي عبارة عن سبيكة
of Journal and Thrust Bearings. ذات قدرة عالية على تحمل األحمال الكبيرة
There are (2) types of bearings . والدوران المستمر بسرعات عالية
available. They are the تقوم كراسي التحميل لحمل العمود-
conventional lubricated bearings RADIAL وعليه األحزاء الدوارة
and the non-lubricated . BEARING
magnetic bearings. كما تقوم بالمحافظة على العمود من-
The Journal Bearings perform التآكل أثناء حركته الدورانية السريعة عليه
(3) major functions: .
1. They support loads both كما تقوم بالمحافظة على الحركة-
steady state and dynamic. THRUST المحورية للعمود
2. They provide stiffness and .BEARING
dampening.
3. They control shaft position.
30
Anti-surge protection
31
ظاهرة التجويع فى الضواغط
Compressor surge
A compressor is in تحدث ظاهرة التجويع عندما
32
External causes and
effects of surge
وفيما يلى بعض األسباب التى تؤدى الى
33
External causes and
effects of surge
حدوث فقط مفاجئ وسعير لسرعة-4
such as variable inlet guide تأدية دورها على الوجه األكمل مثل ريش
vanes. التوجيه متغيرة الزاوية عند المدخل
4. Operator error خطأ من المشغل
34
ANTI-SURGE SYSTEM
Anti-surge and capacity نظام الوقاية من حدوث ظاهرة
controls are the main التجويع هى من أهم أنظمة التحكم
elements of compressor فى الضواغط
control. ويعتمد عملها على توفير حد أدنى
Anti-surge prevents أمن للسريان خالل الضاغط وأن
surge by maintaining a تستهلك العمليات ما تحتاجه
safe minimum flow والمتبقى يرجع الى خط السحب
through the وذلك عن طريق أستخدام صمام
compressor. رجوع أو يتم دفعه الى الهواء فى
This is accomplished by حالة ضواغط الهواء
manipulating a blow-off
or recycle valve.
35
Sealing systems
36
موانع التسرب للضاغط الغازى
Seals of Gas Compressor
Gas compressor seal selection يعتمد أختيار نوع مانع التسرب
depend on the type of
compressor, type of gas, للضاغط على نوع الغاز وضغط
maximum pressure and الغاز ودرجة حرارته
temperature and design
characteristics, types of seals وتصنف موانع التسرب بموانع
can be classified as static and أستاتيكية و موانع ديناميكية
dynamic seal.
Static seal is defined as the seal
وموانع التسرب األستاتيكية هى
where the seal is installed الموانع التى تتركب بين سطحين
between two surfaces without وال يوجد حركة نسبية بين أى من
relative movements. السطحين ومانع التسرب
Dynamic seal is relative
movements between sealing وموانع التسرب الديناميكى يوجد
surfaces is exist. There are main حركة نسبية بين سطحى مانع
two types of seal wet and dry التسريب ويوجد منه نوعان مانع
seal
تسرب مبتل ومانع تسرب جاف
37
Dry Gas Seal Tandem Type
Primary Vent
Bearings
38
Lube oil systems
39
تشتمل دائرة التزييت سواء لعمود الكرنك أو صندوق التروس أو
لتزييت االسطوانة على مضخة تدفع الزيت إلى فلتر الزيت كما
يوجد كبرد للزيت بواسطة المياه وهذه الدائرة مهمة جدا ً
ويجب مراعاة اآلتي -:
التأكد من نظافة فلتر الزيت ويتم تنظيفه كلما استلزم األمر ذلك . .1
مراقبة درجة حرارة الزيت الداخل إلى المبرد والخارج أيضا ً .2
لمعرفة إذا كان المبرد يقوم بوظيفته أم ال مع مراقبة ضغط مياه
التبريد .
مراقبة منسوب الزيت داخل صندوق الكرنك وداخل صندوق .3
التروس وفي الخزنة
40
CRANKCASE OR BEARING
LUBRICATION
Full Pressure
Circulation
Lubrication
41
Splash and Flood
Lubrication
Oil is elevated from the التزييت بالطرطشة والغمر
reservoir by discs on the
crankshaft and is removed يتم فى الضواغط الصغيرة
from the discs by scrapers. ويتم رفع الزيت لتزيت
In some compressors, the oil كراسى التحميل عن طريق
is thrown or splashed into
the pocket over the أداة تشبه الملعقة
crosshead by scoops on the ويوجد مستودع فوق كرسى
crank counterweights.
Oil pockets over the التحميل للتأكد من التزييت
crosshead and over the الجيد لها
double row tapered roller
main bearings assure an
ample supply for these parts.
42
Full Pressure Circulation Lubrication
In this system, a positive فى هذا النظام يتم توصيل الى
displacement pump draws oil
from the reservoir and كراسى التحميل والرأس
delivers it under pressure to
the main bearings and to the المنزلقة عن طريق مضخة
crankpin bearings, and عادة ما تكون ترسية أو
hence to the crosshead pin
bearings and crossheads. حلزونية
43
Full Pressure Circulation Lubrication
On larger machines where ويستخدم هذا النظام فى حالة
large quantities of oil are
being circulated, oil coolers الضواغط الكبيرة
are provided.
Oil pressure safety devices ويزود بنظام حماية ألغالق
are incorporated in the الضاغط فى حالة وجود أى
system to shut the
compressor down in the مشكلة فى نظام التزييت
event of oil pressure failure.
44
Interstage cooling
45
نظام التبريد
Cooling system
Two methods of توجد طريقتان للتبريد طبقا
46