name of the pictures presented EXAMPLE BUS + KIT = BUSKIT (BASKET) KNEE MANKNE MAN + (MONEY) = E LET’S START SCREW DRIVER SCREWDRIV + = ER PHILI PHIL + LIP = P MERMAID HAM + HAMMER = BALL BALLPI (BALLPE PIN = + N EN) ER S COMB BIN + NATION + FLY + ERS = + COMBBINNATION FLYERS (COMBINATION PLIERS) LONG + NOSE = LONG NOSE HACK + SAW = HACKSAW ELECTRICAL TOOLS DIFFERENCE BETWEEN TOOLS AND MATERIALS TOOLS MATERIALS -a device or implement, especially one held in the hand, used to carry out a particular function -instrument or simple piece of -the matter from which a equipment that you hold in thing is or can be made your hands and use to do a particular kind of work ELECTRICAL TOOLS AND EQUIPMENT Electrical task can be accomplished systematically to save time, effort, and resources. Most of the work cannot be done using bare hands. To do the task, electrical tools or equipment are needed to perform the job. This lesson will discuss the function/use of each tool or equipment used in electrical wiring installations. The following are common electrical tools and equipment needed in the installation of electrical wiring. I. Screw drivers. These tools are made of steel hardened and tempered at the tip used to loosen or tighten screws with slotted heads. They come in various sizes and shapes.
A.Standard/Flat Screw Driver.
B.Philips Screw Driver. C.Stubby Screw Driver. D.Allen Screw Driver/Wrench. A. Standard/Flat Screw Driver. The blade tip is wedge-shaped and resembles a negative (-) sign. This is used to drive screws with a single slot head B. Philips Screw Driver. This has a cross tip resembling a positive (+) sign. This is used to drive screws with cross slot heads. C. Stubby Screw Driver. It comes in either Standard or Philips screw driver with short shank or blade and a shorted handle used to turn screws in tight space where standard screw driver cannot be used. D. Allen Screw Driver/Wrench. This could be in the shape of a screw driver or a wrench. Its function is to drive screw with hexagonal slot head. II. Hammers. These are tools used in driving or pounding and pulling out nails. They are made of hard steel, wood, plastic or rubber. The following are types of hammer: A. Claw hammer B. Mallet(rubber head) C. Ballpeen hammer A.Claw hammer
B. Mallet(rubber head) C. Ballpeen hammer
III. Pliers. These made from metal with insulators in the handle and are used for cutting, twisting, bending, holding, and gripping wires and cables. A. Combination Pliers (Lineman’s Pliers). B. Side Cutting Pliers. C. Long Nose Pliers. A. Combination Pliers (Lineman’s Pliers). This is used for gripping, holding, and cutting electrical wires and cables and even small nails. They are usually used by linemen In doing heavy tasks. B. Side Cutting Pliers. This type of pliers is used for cutting fine, medium and big wires and cables. C. Long Nose Pliers. This is used for cutting and holding fine wires. This can reach tight space or small opening where other pliers cannot reach and also used in making terminal loops of copper wires. V. Electrician’s knife. This is used by linemen to remove insulation of wire and cables in low and high voltage transmission lines. VI. Portable electric drill. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in making holes on metal sheets and concrete walls. VII. Hacksaw. This tool is used to cut metal conduit and armored cable. C-CLAMP AMMETER OHMETER VOLTMETER MULTIMETER CLASSIFICATIO N OF ELECTRICAL TOOLS DRIVING TOOL
•any tool used to push (drive) another
object into the wood. Their general purpose is to connect two pieces of materials together, or to connect wood to another material MEASURING TOOL •Electrical measuring instruments, from the name itself, refer to devices used for measuring various electrical aspects such as the presence and amount of current, voltage, resistance and power through installation. EDGE CUTTING TOOL • Woodworkers, cabinetmakers, shopkeepers, builders, electricians and construction workers often refer to edge cutters. They're typically asking for a tool with two knife- like edges at the ends, joined by an axle. With two handles to provide leverage, the cutting edges pinch together to cut wires, plastic, wood, nails, staples or just about anything else you can imagine. BORING TOOL
•In machining, boring is the process of
enlarging a hole that has already been drilled by means of a single-point cutting tool HOLDING TOOLS •A holding tool is a tool that firmly holds any material together. TOOTH CUTTING TOOL MISCELLANEOUS TOOL QUIZ #1 ELECTRICAL TOOLS •1. This type of pliers is used for cutting fine, medium and big wires and cables. •2. This tool is used to cut metal conduit and armored cable. •3. This is used for cutting and holding fine wires. This can reach tight space or small opening •4. A tool used for removing insulation of medium sized wires •5. It is a type of screwdriver that is used to drive screw with hexagonal slot head. •6. It is a measuring tape that coils into a compact case that measures 5m in length •7. It is used to measure the electric current of electrical material or appliances •8. It is a type of pressure sensitive tape used to insulate electrical wires and other materials to conduct electricity •9. It is a lens that produces an enlarged image, used to examine small or finely detailed things •10. It is used to measure the voltage of electrical materials. •11. It is a type of hammer that has a rubber head and usually used in levelling tiles •12. It is a type of hammer that is used remove or pull out nails •13. Classification of any tool used to push another object into the wood •14. Classification of electrical tool that makes and enlarges hole in a concrete walls •15. Classification of electrical tool with two knife-like edges at the ends, joined by an axle. It is used to cut wires, plastic, wood, nails CLASSIFY THE FOLLOWING ELECTRICAL TOOL 16. Screwdriver 17. Side cutting plier 18. Hacksaw 19. C-clamp 20. Push-pull rule