Professional Documents
Culture Documents
www.huawei.com
Common features
Case study
Main Function
Support different tpes of test data
Genex Probe
Huawei RNC
Agilent E6474A
Agilent E7476A
ANT
BYUE
Mobile Agent
▪ RSCP
▪ Ec/Io
▪ HO Event
▪ HSDPA Throughput
▪ ……
Data Disperse:
The dispersing of the drive test data collected in the
period of bus stop into the data collected several
seconds before the bus start. In the way, the data
can be clearly displayed on the map.
User need choose specific mode according to different scenario. Data binning can reduce the
influence on fast fading effectively.
No Binning
Analysis based on original test data. Usually used for events and message synchronous
analysis.
Advantage: Locate at each event and message, for detail trouble shooting.
Disadvantage: 1. Large data amount;
2. Geographic distribution of original test data maybe not even.
Distance Binning
Most common used in drive test. Used for post-processing for CW measurements and statistic analysis for
coverage area.
Advantage : 1. Get even geographic bin on single direction route.
2. Avoid samples accumulation caused of long time stop, e.g. red traffic light.
3. With high efficiency
Disadvantage : not suitable for repeated routes, e.g. bridge.
Example : Compare before and after effects of 5m binning (Required: drive test speed is not too fast)
5m binning
5m*5m binning
higher speed
1 second binning
lower speed
after
Filter by time
Used for distinguish repeated route
before
Method:
• Select the site on the map
• Right-click Show Config Neighbor
Cell
• Select the service cell on the left of the
dialog box
• The neighbor cells will be displayed on
the right of the dialog box. If one
neighbor cell is selected, there will be
only one neighbor cell displayed on
map. We can select multi-neighbor cell
using SHIFT+click.
Event legend
customization
RNC Data
Uplink
data
Downlink
data
Common features
Case study
• By each TBS
By each TBS
Number of retransmissions of the same TB, that is , the number of NACK messages to which the NodeB translates from the ACK
Dup. SB Suc
messages provided by the UE upon successful decoding
Number of failed TB transmissions after retransmissions, that is , the number of frames transmitted at the RLC layer after failed
Block Fail
retransmissions at the MAC layer
2 Times Number of frames successfully transmitted at the second attempt after the first attempt failed
3 Times Number of frames successfully transmitted at the third attempt after the first two attempts failed
4 Times Number of frames successfully transmitted at the fourth attempt after the first three attempts failed
Number of frames successfully transmitted at the fifth attempt after the first four attempts failed
5 Times
After four retransmissions, the RLC initiates the fifth one, which is set on the Huawei equipment
>= 6 Times Number of frames successfully transmitted at the sixth or later attempt after all the previous attempts failed
Common
Case Study
Happy Rate --
Common
Case Study
idge
Br
4. Solutions
Antenna down tilt adjustment
• Reduce antenna down tilt to increase cell coverage range on
the thither side of the bridge. e.g. SC224.
• Increase antenna down tilt to reduce coverage range on the
thither side of the bridge. e.g. SC170 and SC176/SC178.
• Increase antenna down tilt to reduce coverage range along
with the street, e.g. SC26.
Scanner
UE (offset↓)
Scanner
UE (offset↓)
4. Solution
Add SC337 to the intra-frequency neighbor cell list of
SC429.
Ec/Io of SC329 in Active Set is very poor (maybe due to antenna azimuth), and Ec/Io of SC328 in Monitored Set
is much better. Usually, there should be a SHO.
Before call drop, Ec/Io of SC328 (in Monitored Set) is much better than SC329 (in Active Set), and this status
keeps for long time, and match the thresholds of SHO.
In message browser, we will find that UE has sent “Measurement Report” many times and asked for handover (to
SC328 and so on).
4. Troubleshooting
Weak coverage
The characteristic of weak coverage is: weak RSCP and Ec/Io, TxPower
increases, even reaches the maximum before call drop
1. Check the Ec/Io and RSCP around this call drop point
We will find that receive signals in red box are very weak, especially before
the call drop.
Weak coverage
2. Observe RSCP and Ec/Io before call drop
Weak coverage
3. Analysis
The distance from call drop point to SC212 (nearest working cell in Active Set) is 2078m, and the azimuth of
SC212 is reverse to call drop area. There is a much nearer cell SC190, but it seems not to work.
4. Solution
1. Description
Before call drop, UE reports 1F measurement report, but no 2D. That is when UE moves to a GSM
cell, it fails to start compression mode to start inter-RAT measurement.
Cause:
4. After adjustment