Professional Documents
Culture Documents
Start the Probe/Assistant, record down the ESN code to apply for the license.
http://3ms.huawei.com/hi/group/2026401/thread_4821917.html?for_statistic_from=mail_share
License
application Template
HUA_V7.2.9.rar
Import the Engineering Parameter into Probe. Latest version HW should provide.
Go to [Configuration] [Engineering Parameter Management…] .
SMART_TDD_EP_20160108_Internal.rar
FDD EPT_20151005.rar
Choose the “LTE” system. Then select the Engineering Parameter file (in excel format), match the “Excel
Parameter” with the “Probe Parameter”, as shown in below.
Create
New and
Save
Project
LTE
Parameters
and
Messages Show the
plot on the
map, such Check PCI
as RSRP and RSRP
of serving
cell
[Engineering File.xls]
Step 5:
Separated Log Files into different
Groups
Step 2:
Load Outdoor Map
Step 1: .tab file
Create New Project, or
Open Project
Step 4:
Import Log Files
[Add Logfile…]
Select all the logfiles and start to import.
Untick the option [Auto Combine] to prevent
uncorrelated log files combination.
Step 1:
Right Click [Insert Before]
Step 2:
Change Color, Min Value & Max 3 4
Value.
Step 3:
Right Click [Insert Before]
Step 4:
Change Color, Min Value & Max
Value.
Repeat the above steps until
completed for all the value
range.
1 2
Step 1: Step 2:
RSCP plot is using Right click [Load
the default legend Legend]
3 4
Step 3: Step 4:
Select the RSCP plot is now
custom legend plot using the new
legend
Select
required
Analysis
Group
Selected
Analysis
Group DL RLC
Throughput
& UL RLC
Throughput
Ping RTT
Type the command to create empty file: fsutil file createnew <filename> <length>
For example: fsutil tile createnew C:\Documents\200MB 200000000
File created within second, and you may check it under the directory:-
DT Tools Preparation:-
Test laptop
LTE UE E5375 (with SIM)
GPS
Power inverter
l l t
FileZilla
ck a laptop procee
h e
!! C e test efore ting.
b s
Files to get ready with:- to th Probe e for te
Drive Route with sit
Latest engineering parameter file
MapInfo map
Table 1 TARGET
BW (MHz) ANTENNA BACKHAUL (Mbps) Ave DL THROUGHPUT (Mbps) Ave UL THROUGHPUT (Mbps)
LTE-LTE Reselection 1
LTE-LTE PS Handover 1
Requirement:
• Newly integrated site must have no Alarm and no parameter and neighbor deficiencies.
• Test phone & SIM
Procedure:
• Before FT commence, please ensure that the newly integrated site has no Alarm, done parameter check and
with defined neighbors.
• If in cases, that there are alarms and deficiencies, endorsed to implementation for rectification.
• First step of doing the Functionality Test are Mobile Originating (MO) & Mobile Terminating (MT) SMS/MMS
must be done for each sectors.
• For SMS, perform 5 attempts in each sector and log the actual result. The target is 100% successful SMS.
%Success = SMS Received / SMS Attempt
• For MMS, perform 3 attempts in each sector and log the actual result. The target is 100% successful MMS.
%Success = MMS Received / MMS Attempt
• MO and MT of SMS & MMS are stationary testing and can be done by sending the SMS/MMS to itself.
• Take note that these sets of testing will be done in two (2) scenarios, IDLE mode and RRC connected mode
as shown in the table of FT report.
Requirement:
• Newly integrated site must have no Alarm and no parameter and neighbor deficiencies.
• Laptop / Internet Browser
• Test phone & SIM
Procedure:
• Make sure that the LTE SIM is connected.
• Do internet browsing.
• Capture the screen with the successful internet browsing with the connection manager
displaying that the LTE UE is connected.
• One (1) successful attempt is enough per each sector.
PCI
Distance (m)
RSRP (dBm)
UL (Mbps)
• The basic service tests must be done per sector and single user.
• Use CAT3 terminal and Probe & Assistant as the test software for Functionality Test.
• Each test must follow the defined methodology of SMART and this must be coordinated with NOC.
• RF Condition Requirement: Near point : SINR>=25dB, RSRP>=-85dBm
Requirement:
• Newly integrated site must have no Alarm and no parameter and neighbor deficiencies.
• Laptop / Internet Browser / Genex Probe
• Test phone & SIM
Procedure:
• Make sure that the LTE SIM is connected.
3 Cluster Optimization
4 DT Analysis
5 OSS KPI Analysis
6 An Introduction to M2000
Mobility Test
Accessibility Continuous Short Ping (LTE only) Service Set up Success Rate
CSFB (to WCDMA) Voice Short Call CSFB Setup Success Rate, Set-up Time
TARGET MODE
Ave DL THROUGHPUT 65% of SST Targets, but no more than 16Mbps FTP DL Long call l, RSRP>-95dBm
Ave UL THROUGHPUT 65% of SST Targets, but no more than 9Mbps FTP UL Long call, RSRP>-95dBm
CS Fallback Set-up Time ≤11 secs Voice Short Call (CSFB to WCDMA)
Cluster
LTE KPI Formula & counter
TARGET
(L.RRC.ConnReq.Succ.Emc+L.RRC.ConnReq.Succ.HighPri+L.RRC.ConnReq.Succ.Mt+
L.RRC.ConnReq.Succ.MoData)/
RRC Setup Success rate (service) (%) 99.80%
(L.RRC.ConnReq.Att.Emc+L.RRC.ConnReq.Att.HighPri+L.RRC.ConnReq.Att.Mt+L.RR
C.ConnReq.Att.MoData)*100%
RRC Setup Success Rate (Service)* ERAB Setup Success Rate* S1 signaling setup
Call Setup Success Rate (%) 99.30%
Success Rate * 100%
Loop Start
Loop End
SSV Stationary
Ping Test
Average Time
Delay for Ping
Test
Load Legend
Selected
Analysis
Group
Selected
Analysis
Group
Display on Sheet
Graph
Template.xlsx
AND Operation
Select Serving
RSRP
Select Serving
PCC SINR
New Query
Next
Display on Map
Selected
Analysis
Group
Display on Sheet
Graph
Template.xlsx
Selected Analysis
Group
Display on Sheet
RSRP DL SINR
DL Throughput UL Throughput
Example:- Example:-
Probe-BRGYTEGERF-DT-Download- BRGYTEGERF-Sec1-PCI155-TestLoc1.bmp
20140617.gen BRGYTEGERF-Sec1-PCI155-TestLoc1-SpeedTest1.bmp
Probe-BRGYTEGERF-DT-Upload- BRGYTEGERF-Sec1-PCI155-TestLoc1-SpeedTest2.bmp
20140617.gen **Submit DT route in advance to get BRGYTEGERF-Sec1-PCI155-TestLoc1-SpeedTest3.bmp
… approval from GT BRGYTEGERF-Sec1-PCI155-TestLoc1-SpeedTest4.bmp
BRGYTEGERF-Sec1-PCI155-TestLoc1-SpeedTest5.bmp
Probe-BRGYTEGERF-Sec1-PCI155-TestLoc1-Ping-
20140617.gen
SSV Reports …
Analyze the test log files using GENEX Assistant
Daily monitoring and optimized KPI performance for a period of 14 days
Summarize and complete the report in the SSV Report Template as agreed by GT and HT