Professional Documents
Culture Documents
Equipment VRF Systemes (JPM)
Equipment VRF Systemes (JPM)
Management
Week/Lesson 7
absorption refrigeration
Explain how refrigerants absorb and reject heat
types of compressors
Introduction to the Refrigeration Cycle and Equipment
chiller evaporators
Describe the operation of the absorption
refrigeration cycle
Introduction to the Refrigeration Cycle and Equipment
Refrigeration capacity
Rated in tons of refrigeration effect
Example:
Refrigerants
Absorb heat by evaporating a low temperature
and pressure
Reject heat by condensing at a higher temperature
and pressure
Halogen refrigerants are commonly used in
of the refrigerant
Condenser – removes heat that was added to the
evaporator
Evaporator – heat is absorbed from the space
Introduction to the Refrigeration Cycle and Equipment
Compressors – reciprocating
Equipped with pistons and cylinders
difference across it
Can be open, semi-hermetic or fully hermetic
Introduction to the Refrigeration Cycle and Equipment
Compressors – rotary
Uses circular motion to obtain compression
Utilizes an impeller
Air-cooled condensers
Desuperheating – removes sensible heat
heat)
Subcooling – Addition sensible heat is removed
Water-cooled condensers
Shell-and-tube
Shell-and-coil
• Similar to the shell-and-tube
• Used in smaller applications
• Tubes are now in a coil shape
• Must be cleaned chemically
Introduction to the Refrigeration Cycle and Equipment
Tube-within-a-tube
• Water flows in the inner tube
• Refrigerant flows in the outer tube
• Heat travels from the refrigerant
To the surrounding air, and
Evaporative condenser
Utilizes air and water
Metering devices
Thermostatic expansion valve
Capillary tube
Orifice plates
Introduction to the Refrigeration Cycle and Equipment
valve to close
A decrease in evaporator pressure will cause the
valve to open
Commonly used on systems with constant loads
Introduction to the Refrigeration Cycle and Equipment
Capillary tubes
– Seamless tubing with a small inside diameter
– No moving parts
High side float valve
– Introduces refrigerant to the evaporator at the
same rate as it leaves
– A float on the high side maintains proper flow
Introduction to the Refrigeration Cycle and Equipment
Orifice plates
Used primarily on centrifugal chillers
the load
High load liquid passes the plates
to a vapor
Introduction to the Refrigeration Cycle and Equipment
Refrigerant: Water
Introduction to the Refrigeration Cycle and Equipment
Absorber
Concentrator
Condenser
Introduction to the Refrigeration Cycle and Equipment
Evaporator
Operates at very low pressures (0.25 psia)
Absorber
Refrigerant from the evaporator enters absorber
temperature
Introduction to the Refrigeration Cycle and Equipment
Concentrator
Dilute absorbent solution flows to the
concentrator
Heat sources boil the refrigerant from the
absorbent
The solution now becomes highly concentrated
Condenser
Responsible for supplying liquid refrigerant to the
evaporator
The refrigerant vapor leaves the concentrator
• When refrigerant absorbs the unwanted heat, this raises the refrigerant’s
temperature (“Saturation Temperature”) so that it changes from a liquid
to a gas — it evaporates. The system then uses condensation to release
the heat and change the refrigerant back into a liquid. This is called
“Latent Heat”.
• This cycle is based on the physical principle, that a liquid extracts heat
from the surrounding area as it expands (boils) into a gas.
• The closed looped pipe system stops the refrigerant from becoming
contaminated and controls its stream. The refrigerant will be both a vapor
and a liquid in the loop.
“Saturation Temperature” – can be defined as the temperature of a liquid,
vapor, or a solid, where if any heat is added or removed, a change of state
takes place.
• The Compressor
• The Condensing Coil
• The Metering Device
• The Evaporator