Professional Documents
Culture Documents
Transfer PDF
Transfer PDF
CENTER DIFFERENTIAL
TR06J-02
COMPONENTS
High Speed Output Gear Front Drive Gear Piece Clutch Hub High and Low Clutch Sleeve Needle Roller Bearing Front Taper Roller Bearing Thrust Washer Straight Pin Low Gear Pinion Shaft
See page TR-31
S Snap Ring
Differential Thrust Washer Front Case Nm (kgfcm, ftlbf) : Specified torque S Non-reusable part
D04344
Author :
Date :
1915
TR-28
TRANSFER CENTER DIFFERENTIAL
TR06K-02
DISASSEMBLY
1. (a) INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND THRUST CLEARANCE Using a feeler gauge, measure the high speed output gear thrust clearance. Standard clearance: 0.10 - 0.25 mm (0.0039 - 0.0098 in.) Maximum clearance: 0.25 mm (0.0098 in.) Using a dial indicator, measure the high speed output gear radial clearance. Standard clearance: 0.035 - 0.091 mm (0.00138 - 0.00358 in.) Maximum clearance: 0.091 mm (0.00358 in.)
TF0900
(b)
TF0944
SST
2. (a) (b)
REMOVE FRONT DRIVE GEAR PIECE Using a snap ring expander, remove the snap ring. Using SST and a press, remove the front drive gear piece. SST 09950-00020, 09950-60010 (09951-00320) NOTICE: Be careful not to drop the center differential assembly.
Q07101
SST
3. REMOVE FRONT TAPER ROLLER BEARING Using SST and a press, remove the front taper roller bearing. SST 09950-00020 NOTICE: Set the claw of SST to the bearing inner race securely.
Q07102
4. 5.
D02679
Author :
Date :
1916
TR-29
TRANSFER CENTER DIFFERENTIAL
6.
D02680
7. (a)
SST
(b)
Q07103
REMOVE HIGH SPEED OUTPUT GEAR BUSHING AND CLUTCH HUB Using SST, remove the high speed output gear bushing and clutch hub. SST 09950- 00020, 09950- 00030, 09950- 60010 (09951-00320) Using a magnetic finger, remove the straight pin from the differential front case.
SST
8. REMOVE REAR TAPER ROLLER BEARING Using SST and a press, remove the rear taper roller bearing. SST 09950-00020, 09950-60010 (09951-00320) NOTICE: Set the claw of SST to the bearing inner race securely.
Q07113
9. REMOVE DIFFERENTIAL REAR CASE Remove the 12 bolts and differential rear case.
D02681
10.
D02682
Author :
Date :
1917
TR-30
TRANSFER CENTER DIFFERENTIAL
11. (a)
REMOVE PINION SHAFT, 2 PINION GEARS AND 2 THRUST WASHERS Remove the straight pin from the pinion shaft.
D02683
(b)
D02684
(c)
D02685
12. REMOVE LOW GEAR Using a plastic hammer, tap and remove the low gear. NOTICE: Be careful not to damage the low gear.
D02686
Author :
Date :
1918
TR-31
TRANSFER CENTER DIFFERENTIAL
TR06L-02
REASSEMBLY
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly.
INSTALL LOW GEAR Clean the contact surface of the differential case. Heat the low gear in boiling water. Carefully remove the low gear from the water. After the moisture on the low gear has completely evaporated, quickly install the low gear to the differential case.
D02687
2.
TF1012
3. (a)
INSTALL PINION SHAFT, 2 PINION GEARS AND 2 THRUST WASHERS Install the pinion shaft, 2 pinion gears and thrust washers to the differential front case.
TF0913
Author :
Date :
1919
TR-32
TRANSFER CENTER DIFFERENTIAL
(b) Using a dial indicator, measure the front case backlash. HINT: Push the pinion shaft. Maximum backlash: 0.05 mm (0.0020 in.) If the backlash is not within the specification, replace the thrust washer with one of the correct size and reinstall the thrust washer.
Thickness mm (in.)
TF0917
Thickness mm (in.) 2.45 (0.0965) 2.60 (0.1024) 2.75 (0.1083) 2.90 (0.1142) 3.05 (0.1201)
1.70 (0.0669) 1.85 (0.0728) 2.00 (0.0787) 2.15 (0.0846) 2.30 (0.0906)
(c) 4. 5.
In the same way, measure the rear case backlash. INSTALL STRAIGHT PIN TO PINION SHAFT INSTALL REAR SIDE GEAR AND THRUST WASHER
INSTALL DIFFERENTIAL REAR CASE Install the differential rear case and 12 set bolts. Torque: 88 Nm (900 kgfcm, 65 ftlbf) Turn the pinion gear. Loosen the 12 rear case set bolts. Torque the 12 rear case set bolts. Torque: 98 Nm (1,000 kgfcm, 72 ftlbf)
TF0920
7. INSTALL REAR TAPER ROLLER BEARING Using SST and a press, install the rear taper roller bearing. SST 09316-12010
SST
Q00534
8. INSTALL CLUTCH HUB Using SST and a press, install the clutch hub. SST 09316-12010, 09316-60011 (09316-00011)
SST
SST
Q00547
Author :
Date :
1920
TR-33
TRANSFER CENTER DIFFERENTIAL
9. (a) (b)
INSTALL HIGH SPEED OUTPUT GEAR BUSHING Apply MP grease to the straight pin. Install the straight pin, as shown.
Q00549
(c)
Groove
Using SST and a press, install the high speed output gear bushing. SST 09316-12010, 09316-60011 (09316-00011) NOTICE: Before pressing on the differential front case, align the groove on the bushing with the pin on the shaft.
SST Pin
D04312
Q00555
10. INSTALL HIGH AND LOW CLUTCH SLEEVE HINT: Make sure to install the high and low clutch sleeve in the correct direction. 11. INSTALL NEEDLE ROLLER BEARING AND HIGH SPEED OUTPUT GEAR (a) Apply gear oil to the needle roller bearing. (b) Install the needle roller bearing and high speed output gear. 12. INSTALL FRONT TAPER ROLLER BEARING Using SST and a press, install the front taper roller bearing. SST 09316-12010, 09316-60011 (09316-00011)
SST
SST
Q00539
Author :
Date :
1921
TR-34
TRANSFER CENTER DIFFERENTIAL
SST
13. INSTALL FRONT DRIVE GEAR PIECE Using SST and a press, install the front drive gear piece. SST 09316-12010, 09316-60011 (09316-00011)
SST
Q00540
14. (a)
A B C D E
TF0931
INSTALL SNAP RING Select a snap ring that will allow the minimum axial play.
Thickness mm (in.) 2.00 (0.0787) 2.10 (0.0827) 2.20 (0.0866) 2.30 (0.0906) 2.40 (0.0945) 2.50 (0.0984) Mark G H J K L Thickness mm (in.) 2.60 (0.1024) 2.70 (0.1063) 2.80 (0.1102) 1.80 (0.0709) 1.90 (0.0748) -
Mark
(b) 15.
Using a snap ring expander, install a new snap ring. INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND THRUST CLEARANCE (See page TR-28 )
Author :
Date :
1922
TR-35
TRANSFER FRONT EXTENSION HOUSING
COMPONENTS
Dust Deflector Snap Ring Front Output Shaft Drive Clutch Hub Snap Ring Ball Bearing Front Extension Housing Oil Seal
Non-reusable part
Z18836
Author :
Date :
1923
TR-36
TRANSFER FRONT EXTENSION HOUSING
TR06N-03
DISASSEMBLY
1. (a) (b) REMOVE DRIVE CLUTCH HUB Using a snap ring expander, remove the snap ring. Using SST, remove the drive clutch hub. SST 09950- 40011 (09951- 04020, 09952- 04010, 09953- 04030, 09954- 04020, 09955- 04021, 09957-04010, 09958-04011)
SST
Q07133
2. REMOVE FRONT OUTPUT SHAFT Using a plastic hammer, drive out the front output shaft.
TF1036
3. (a)
REMOVE DUST DEFLECTOR Using SST, remove the dust deflector. SST 09950- 40011 (09951- 04020, 09952- 04010, 09953- 04030, 09954- 04010, 09955- 04051, 09957-04010, 09958-04011)
SST
D02660
(b)
Using a screwdriver and hammer, tap the dust deflector and remove it from the extension housing.
TF0937
4. REMOVE OIL SEAL Using a screwdriver, pry out the oil seal from the front extension housing.
TF0938
Author :
Date :
1924
TR-37
TRANSFER FRONT EXTENSION HOUSING
5. (a)
TF0939
(b)
Using SST and a press, remove the ball bearing. SST 09316-6001 1 (09316-00011, 09316-00071)
SST
TF0940
Author :
Date :
1925
TR-38
TRANSFER FRONT EXTENSION HOUSING
TR06O-02
REASSEMBLY
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly. 1. INSTALL DUST DEFLECTOR (a) Using a plastic hammer, install a new dust deflector to the front extension housing.
TF1058
(b)
Using SST and a press, install a new dust deflector to the front output shaft. SST 09316-2001 1, 09316-60011 (09316-00011)
SST
TF0967
2. (a)
SST
INSTALL BALL BEARING Using SST and a press, install the ball bearing to the front extension housing. SST 09316-6001 1 (09316-00011, 09316-00031)
TF0943
(b)
Select a snap ring that will allow the minimum axial play.
Mark A B Thickness mm (in.) 1.70 (0.0669) 1.80 (0.0709)
(c)
TF0939
3. (a) (b)
INSTALL OIL SEAL Apply MP grease to the lip of a new oil seal. Using SST and a hammer, drive in a new oil seal to the front extension housing. SST 09316-6001 1 (09316-00011, 09316-00061)
SST
TF0945
Author :
Date :
1926
TR-39
TRANSFER FRONT EXTENSION HOUSING
4. (a)
SST
INSTALL FRONT OUTPUT SHAFT AND DRIVE CLUTCH HUB Using SST and a press, install the front output shaft and drive clutch hub. SST 09316-2001 1, 09316-60011 (09316-00011, 09316-00041, 09316-00071)
SST
Q00542
(b)
Select a snap ring that will allow the minimum axial play.
Mark A B C D E Thickness mm (in.) 1.80 (0.0709) 1.90 (0.0748) 2.00 (0.0787) 2.10 (0.0827) 2.20 (0.0866)
TF0933
(c)
Author :
Date :
1927
TR-22
TRANSFER IDLER GEAR
IDLER GEAR
TR06F-02
COMPONENTS
Idler Gear
Rear Taper Roller Bearing Idler Low Gear Needle Roller Bearing High and Low Clutch Sleeve
Z15264
Author :
Date :
1910
TR-23
TRANSFER IDLER GEAR
TR06G-03
DISASSEMBLY
1. (a) INSPECT IDLER LOW GEAR RADIAL AND THRUST CLEARANCE Using a feeler gauge, measure the idler low gear thrust clearance. Standard clearance: 0.125 - 0.275 mm (0.00492 - 0.01083 in.) Maximum clearance: 0.275 mm (0.01083 in.) Using a dial indicator, measure the idler low gear radial clearance. Standard clearance: 0.015 - 0.068 mm (0.00059 - 0.00268 in.) Maximum clearance: 0.068 mm (0.00268 in.)
TF0887
(b)
TF0888
SST
2. REMOVE FRONT TAPER ROLLER BEARING Using SST, remove the front taper roller bearing. SST 09950- 40011 (09951- 04010, 09952- 04010, 09953- 04030, 09954- 04010, 09955- 04061, 09957- 04010, 09958- 04011), 09950- 60010 (09951-00330) NOTICE: Set the claw of SST to the bearing inner race securely.
D02888
Socket Wrench
SST
3. REMOVE REAR TAPER ROLLER BEARING Using SST, a press and socket wrench, remove the rear taper roller bearing. SST 09950-00020 NOTICE: Set the claw of SST to the bearing inner race securely.
Q07100
4.
REMOVE IDLER LOW GEAR AND NEEDLE ROLLER BEARING FROM IDLER GEAR
D02674
Author :
Date :
1911
TR-24
TRANSFER IDLER GEAR
5.
D02675
Author :
Date :
1912
TR-25
TRANSFER IDLER GEAR
TR06H-02
INSPECTION
1. INSPECT IDLER GEAR Using a micrometer, measure the idler gear diameter. Standard diameter: 38.48 - 38.50 mm (1.5149 - 1.5157 in.) Maximum diameter: 38.50 mm (1.5157 in.)
D02676
2. INSPECT IDLER LOW GEAR Using a cylinder gauge, measure the idler low gear diameter. Standard diameter: 45.52 - 45.54 mm (1.7922 - 1.7930 in.) Maximum diameter: 45.54 mm (1.7930 in.)
D02677
Author :
Date :
1913
TR-26
TRANSFER IDLER GEAR
TR06I-02
REASSEMBLY
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly. 1. INSTALL FRONT TAPER ROLLER BEARING Using SST and a press, install the front taper roller bearing. SST 09316-6001 1 (09316-00011, 09316-00031)
TF0893
SST
2. INSTALL HIGH AND LOW CLUTCH SLEEVE HINT: Make sure to install the high and low clutch sleeve in the correct direction.
Q00538
3. (a) (b)
INSTALL NEEDLE ROLLER BEARING AND IDLER LOW GEAR TO IDLER GEAR Apply gear oil to the needle roller bearing. Install the needle roller bearing and idler low gear.
D02678
SST
4. INSTALL REAR TAPER ROLLER BEARING Using SST and a press, install the rear taper roller bearing. SST 09316-6001 1 (09316-00011, 09316-00071) 5. INSPECT IDLER LOW GEAR RADIAL AND THRUST CLEARANCE (See page TR-25 )
TF0896
Author :
Date :
1914
TR-19
TRANSFER INPUT SHAFT
INPUT SHAFT
TR06C-02
COMPONENTS
S Snap Ring
S Non-reusable part
D02654
Author :
Date :
1907
TR-20
TRANSFER INPUT SHAFT
TR06D-03
DISASSEMBLY
1. (a) REMOVE REAR BALL BEARING Using a snap ring expander, remove the snap ring.
D02691
(b)
Socket Wrench
Using a socket wrench and press, remove the rear ball bearing.
D02853
2. (a) (b)
SST
REMOVE FRONT BALL BEARING Using a snap ring expander, remove the snap ring. Using SST, remove the front ball bearing. SST 09950- 40011 (09951- 04020, 09952- 04010, 09953- 04030, 09954- 04010, 09955- 04011, 09957- 04010, 09958- 04011), 09950- 60010 (09951-00400)
D02655
Author :
Date :
1908
TR-21
TRANSFER INPUT SHAFT
TR06E-02
REASSEMBLY
SST
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly. 1. INSTALL FRONT BALL BEARING (a) Using SST and a press, install a new front ball bearing. SST 09316-6001 1 (09316-00011)
D02656
(b)
A B C
Select a snap ring that will allow the minimum axial play.
Thickness mm (in.) 2.90 (0.1141) 2.95 (0.1161) 3.00 (0.1181) Mark D E F Thickness mm (in.) 3.05 (0.1201) 3.10 (0.1220) 3.15 (0.1240)
Mark
(c)
D02657
2. (a)
SST
INSTALL REAR BALL BEARING Using SST and a press, install the rear ball bearing. SST 09316-6001 1 (09316-00011, 09316-00031)
D02658
(b)
Select a snap ring that will allow the minimum axial play.
Mark A B C D E Thickness mm (in.) 2.00 (0.0787) 2.10 (0.0827) 2.20 (0.0866) 2.30 (0.0906) 2.40 (0.0945)
D02659
(c)
Author :
Date :
1909
TR-49
TRANSFER MOTOR SHIFT CONTROL SYSTEM
TR06V-02
INSPECTION
1. (a)
ON OFF
(b)
INSPECT SWITCH POSITION Start the engine, and shift the transfer shift lever to the H position. Check that the center diff. indicator light comes on when the the switch is in ON position. Check that the light goes off when the switch is in OFF position.
D02866
2. (a) (b)
L N H
INSPECT SHIFT LEVER POSITION Start the engine, and turn the center diff. lock switch to OFF. Check that the center diff. indicator light comes on when the transfer shift lever is shifted to the L position. Check that the light goes off when the lever is shifted to the N or H position.
D02867
Relay side:
3. (a)
INSPECT CENTER DIFF. LOCK CONTROL RELAY Check that continuity exists between each terminal, as shown in the chart.
Tester connected terminal number 1-2 2-4 6-7 Specified condition Continuity Continuity *
Z15367
*: There is a diode between the terminals 6 and 7. If no continuity exists, check that continuity exists when changing the position of probe for the position of negative probe of tester. (b) Apply battery positive voltage between each terminal and check that continuity exists between each terminal, as shown in the chart.
Battery voltage applied terminal 6 (+) - 5 (-) 7 (+) - 2 (-) 9 (+) - 10 (-) Tester connected terminal number 1-3 1-2 9 - 10 3-4 2-4 Specified condition Continuity No continuity No continuity Continuity No continuity
Author :
Date :
1937
TR-50
TRANSFER MOTOR SHIFT CONTROL SYSTEM
Free Lock
4 1
2 5 3
54 3 21
INSPECT ACTUATOR OPERATION Raise up the front wheels, place the stopper under the rear wheels to block them, and pull up the parking brake. Disconnect the connector of the actuator and connect it to the relay using wire. Check that the front propeller shaft can be rotated by hand.
Inspection Item Center Diff. Free Lock Standard Front propeller shaft cannot be rotated.
Lock Free
4 1
2 5 3
5 4 3 21
D02869
2 4 1 5 3
HINT: When inspecting the operation described above, use a heater main relay. NOTICE: Connect the terminals being careful not to touch the neighboring terminals or metallic parts of relay housing.
4
D04311
D02663
INSPECT MOTOR ACTUATOR (MOTOR) Remove the motor actuator (See page TR-8 ). Measure the resistance between the terminals 1 and 5. Standard resistance: 0.3 - 100 (c) Measure the resistance between the terminals 1 or 5 and body ground. Standard resistance: More than 0.5 M If the resistance value is not as specified, replace the motor actuator.
5. (a) (b)
Author :
Date :
1938
TR-51
TRANSFER MOTOR SHIFT CONTROL SYSTEM
6. (a) (b)
3 2 1
D02877
INSPECT CENTER DIFF. LOCK SWITCH CONTINUITY Remove the center diff. lock switch (See page AC-102 ). Inspect the continuity between each terminal.
Tester connected terminal number 1-2 1-3 2-3 1-2 1-3 2-3 Specified condition No continuity No continuity Continuity Continuity No continuity No continuity
ON
OFF
Ball
7. (a) (b)
270.82mm ON-OFF
D02665
INSPECT TRANSFER INDICATOR SWITCH CONTINUITY Remove the 3 transfer indicator switches (See page TR-8 ). Check that continuity exists between terminals 1 and 2 when pushing the ball at the tip of the switch.
Author :
Date :
1939
TR-48
TRANSFER MOTOR SHIFT CONTROL SYSTEM
LOCATION
Transfer Indicator Switch (Low Switch) Transfer Indicator Switch (Neutral Switch)
D03520
Author :
Date :
1936
TR-40
TRANSFER REAR EXTENSION HOUSING
COMPONENTS
Rear Output Shaft Dust Deflector Ball Bearing Speed Sensor Drive Gear
4.9 (50, 43 in.lbf)
Seal Ring
Oil Seal
Snap Ring
Ball
S Screw Plug
29 (300, 22)
Driven Rotor Snap Ring Oil Pump Cover Oil Pump Plate Oil Pump Drive Shaft
Drive Rotor
4.9 (50, 43 in.lbf)
D04346
Author :
Date :
1928
TR-41
TRANSFER REAR EXTENSION HOUSING
TR06Q-02
DISASSEMBLY
1. REMOVE OIL PUMP DRIVE SHAFT
TF1039
REMOVE OIL PUMP COVER Using a torx socket wrench (T30), remove the 3 screws. Install the 2 suitable bolts to the pump cover. Remove the pump cover from the rear extension housing.
Q00530
3.
TF1033
4.
TF1034
5. (a) (b)
REMOVE SCREW PLUG, SPRING, BALL AND VALVE SEAT Using a hexagon wrench, remove the screw plug. Using a magnetic finger, remove the spring, ball and valve seat from the rear extension housing.
Q08384
Author :
Date :
1929
TR-42
TRANSFER REAR EXTENSION HOUSING
6. REMOVE OIL PUMP PLATE Remove the 3 bolts and oil pump plate. 7. REMOVE SPEED SENSOR DRIVE GEAR (a) Using a snap ring expander, remove the snap ring. (b) Remove the speed sensor drive gear.
D04353
8. (a) (b)
SST
TF0959
REMOVE REAR OUTPUT SHAFT Using a snap ring expander, remove the snap ring. Using SST and a hammer, remove the rear output shaft. SST 09325-12010 (c) Remove the 2 seal rings from the rear output shaft. 9. REMOVE DUST DEFLECTOR (a) Using a screwdriver and hammer, remove the rear extension housing dust deflector. (b) Using a screwdriver and hammer, remove the rear output shaft dust deflector. 10. REMOVE OIL SEAL Using a screwdriver, pry out the oil seal from the rear extension housing.
Q08385
REMOVE BALL BEARING Using a screwdriver, remove the snap ring. Using SST and a press, remove the ball bearing from the rear extension housing. SST 09316-6001 1 (09316-00011, 09316-00021)
Q08481
Author :
Date :
1930
TR-43
TRANSFER REAR EXTENSION HOUSING
TR06R-02
INSPECTION
1. (a) INSPECT DRIVEN ROTOR BODY CLEARANCE Install the drive rotor and driven rotor to the rear extension housing. (b) Using a feeler gauge, measure the body clearance between the drive rotor and extension housing. Standard clearance: 0.08 - 0.17 mm (0.0031 - 0.0067 in.) Maximum clearance: 0.17 mm (0.0067 in.) If the body clearance exceeds the maximum, replace the drive rotor and driven rotor.
Q02615
Q02616
2. INSPECT DRIVEN ROTOR TIP CLEARANCE Using a feeler gauge, measure the tip clearance between the drive rotor and driven rotor. Standard clearance: 0.05 - 0.15 mm (0.0020 - 0.0059 in.) Maximum clearance: 0.15 mm (0.0059 in.) If the tip clearance exceeds the maximum, replace the drive rotor and driven rotor. 3. INSPECT OIL PUMP SIDE CLEARANCE Using a steel straight edge and feeler gauge, measure the side clearance of oil pump. Standard clearance: 0.03 - 0.10 mm (0.0012 - 0.0039 in.) Maximum clearance: 0.10 mm (0.0039 in.) If the side clearance exceeds the maximum, replace the drive rotor and driven rotor.
Q02617
Author :
Date :
1931
TR-44
TRANSFER REAR EXTENSION HOUSING
TR06S-02
REASSEMBLY
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly. 1. INSTALL BALL BEARING (a) Using SST and a press, install the ball bearing. SST 09316-6001 1 (09316-00011, 09316-00031)
TF0964
SST
(b)
Select a snap ring that will allow the minimum axial play.
Mark A B Thickness mm (in.) 1.70 (0.0669) 1.80 (0.0709)
(c)
TF0962
2. (a)
INSTALL DUST DEFLECTOR Using SST and a hammer, install a new rear extension housing dust deflector. SST 09316-6001 1 (09316-00011, 09316-00041)
SST
Q08482
(b)
Using SST and a press, install a new rear output shaft dust deflector. SST 09316-2001 1, 09316-60011 (09316-00011)
SST
TF0967
3. (a) (b)
SST
INSTALL OIL SEAL Apply MP grease to the lip of a new oil seal. Using SST and a hammer, drive in the oil seal. SST 09316-6001 1 (09316-00011, 09316-00031)
Q08482
Author :
Date :
1932
TR-45
TRANSFER REAR EXTENSION HOUSING
4. (a)
SST
(b)
INSTALL REAR OUTPUT SHAFT Using SST and a press, install the rear output shaft. SST 09316- 20011, 09316- 60011 (09316- 00011, 09316-00031) Install the 2 seal rings to the rear output shaft.
TF0969
(c)
Select a snap ring that will allow the minimum axial play.
Mark 1 2 3 4 Thickness mm (in.) 1.95 (0.0768) 2.05 (0.0807) 2.15 (0.0847) 2.25 (0.0886)
TF0958
Using a snap ring expander, install a new snap ring. INSTALL SPEED SENSOR DRIVE GEAR Install the speed sensor drive gear. Using a snap ring expander, install the snap ring.
6. (a) (b)
INSTALL OIL PUMP PLATE Install the oil pump plate. Install and torque the 3 bolts. Torque: 4.9 Nm (50 kgfcm, 43 in.lbf)
D04353
Author :
Date :
1933
TR-46
TRANSFER REAR EXTENSION HOUSING
Q08384
(d)
INSTALL VALVE SEAT, BALL, SPRING AND SCREW PLUG Apply gear oil to the ball. Install the valve seat, ball and spring. Apply liquid sealer to the screw plug threads. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent Using a hexagon wrench, install and torque the screw plug. Torque: 29 Nm (300 kgfcm, 22 ftlbf)
8. INSTALL DRIVEN ROTOR (a) Apply gear oil to the driven rotor. (b) Install the driven rotor. 9. INSTALL DRIVE ROTOR (a) Apply gear oil to the drive rotor. (b) Install the drive rotor. HINT: Align the alignment marks.
TF0977
Q00529
INSTALL OIL PUMP COVER Install the oil pump cover. Using a torx socket wrench (T30), install and torque the 3 screws. Torque: 4.9 Nm (50 kgfcm, 43 in.lbf) NOTICE: Align the oil hole of the rear extension housing and oil groove end of the oil pump cover. 11. INSTALL OIL PUMP DRIVE SHAFT
Author :
Date :
1934
TR-7
TRANSFER TRANSFER ASSEMBLY
TRANSFER ASSEMBLY
TR069-02
COMPONENTS
Transfer Indicator Switch (Low Switch)
37 (380, 27)
Gasket S 37 (380, 27) Rear Case Bearing Race Center Differential Assembly Bearing Race Slotted Spring Pin Oil Strainer Adjusting Shim x8
Case Cover x5 S
37 (380, 27)
Snap Ring
Bearing Race
18 (185, 13)
Motor Actuator Output Gear Snap Ring Shift Fork No. 2 Shaft Shift Fork No. 2 Transfer Indicator Switch (Center Diff. Lock)
37 (380, 27)
Input Shaft Assembly Lever Lock Pin Shift Outer Lever Washer Oil Seal Shift Inner Lever
12 (120, 9)
37 (380, 27)
Breather Hose
D02653
Author :
Date :
1895
TR-8
TRANSFER TRANSFER ASSEMBLY
TR06X-02
DISASSEMBLY
1. REMOVE BREATHER HOSE 2. REMOVE VEHICLE SPEED SENSOR DRIVEN GEAR Remove the bolt and driven gear.
D02690
4.
D02862
5. REMOVE SCREW PLUG, SPRING AND BALL (a) Using a torx socket wrench (T40), remove the screw plug. (b) Using a magnetic finger, remove the spring and ball. 6. REMOVE TRANSFER INDICATOR SWITCH Remove the 3 transfer indicator switches and 3 gaskets.
Q07105
7. REMOVE FRONT EXTENSION HOUSING Remove the 6 bolts and front extension housing. HINT: If necessary, tap the front extension housing lightly with a plastic hammer.
D02860
Author :
Date :
1896
TR-9
TRANSFER TRANSFER ASSEMBLY
8.
REMOVE CLUTCH SLEEVE WITH SHIFT FORK NO. 2 SHAFT AND SHIFT FORK NO. 2
Front
Q00541
9. (a) (b)
SEPARATE SHIFT FORK NO. 2 SHAFT AND SHIFT FORK NO. 2 Using 2 screwdrivers and a hammer, tap out the 3 snap rings from the shift fork No. 2 shaft. Separate the shift fork No. 2 shaft and shift fork No. 2.
Q02950
10. REMOVE REAR EXTENSION HOUSING Remove the 9 bolts and rear extension housing. HINT: If necessary, tap the rear extension housing lightly with a plastic hammer. 11. REMOVE ADJUSTING SHIMS
D02861
12. REMOVE OIL STRAINER FROM REAR CASE Remove the 2 bolts and oil strainer.
D02667
13. (a)
D02863
Author :
Date :
1897
TR-10
TRANSFER TRANSFER ASSEMBLY
(b)
Using a brass bar and hammer, tap the case cover and remove it.
D02668
14. (a)
SEPARATE FRONT CASE AND REAR CASE Using a snap ring expander, remove the snap ring from the rear case.
D02669
(b) (c)
Remove the 8 bolts. Using a brass bar and hammer, tap the rear case and separate it.
D02864
15.
TF0854
16. REMOVE INPUT SHAFT ASSEMBLY Using a plastic hammer, remove the input shaft assembly from the front case.
D02670
Author :
Date :
1898
TR-1 1
TRANSFER TRANSFER ASSEMBLY
17.
REMOVE IDLER GEAR ASSEMBLY WITH CENTER DIFFERENTIAL ASSEMBLY, SHIFT FORK NO. 1 AND SHIFT FORK NO. 1 SHAFT FROM FRONT CASE
TF0986
SEPARATE SHIFT FORK NO. 1 AND SHIFT FORK NO. 1 SHAFT Using a pin punch and hammer, drive out the slotted spring pin. Separate the shift fork No. 1 and shift fork No. 1 shaft.
TF0857
REMOVE SHIFT OUTER LEVER AND INNER LEVER Remove the nut and washer from the shift outer lever. Using a brass bar, hammer and socket wrench, tap out the lever lock pin. Remove the shift outer lever, washer and inner lever from the front case.
Socket Wrench
D04308
20. (a)
IF NECESSARY, REPLACE INNER SHIFT LEVER OIL SEAL Using a screwdriver, pry out the oil seal from the front case.
D02671
(b) (c)
Apply MP grease to the lip of a new oil seal. Using SST and a hammer, drive in a new oil seal. SST 09950- 60010 (09951- 00270), 09950- 70010 (09951-07150)
SST
TF0862
Author :
Date :
1899
TR-12
TRANSFER TRANSFER ASSEMBLY
21. (a)
SST
(b) (c)
SST
IF NECESSARY, REPLACE INPUT SHAFT OIL SEAL Using SST and a hammer, drive out the oil seal. SST 09316-6001 1 (09316-00011) Apply MP grease to the lip of a new oil seal. Using SST and a hammer, drive in a new oil seal. SST 09316-6001 1 (09316-00011, 09316-00031)
TF0864
22. REMOVE OIL RECEIVER FROM FRONT CASE Remove the bolt and oil receiver.
D02672
23. (a)
REMOVE 2 BEARING RACES FROM FRONT CASE Using SST, remove the bearing race (for the idler gear). SST 09950- 40011 (09951- 04020, 09952- 04010, 09953- 04030, 09954- 04010, 09955- 04061, 09957-04010), 09950-60010 (09951-00320)
SST
D02770
(b)
Using a brass bar and hammer, remove the bearing race (for the output shaft).
TF0867
Author :
Date :
1900
TR-13
TRANSFER TRANSFER ASSEMBLY
TR06Y-01
REASSEMBLY
1. INSPECT SHIFT FORK NO. 2 AND CLUTCH SLEEVE CLEARANCE Using a feeler gauge, measure the clearance between the shift fork No. 2 and clutch sleeve. Standard clearance: 0.10 - 0.40 mm (0.0039 - 0.0157 in.) Maximum clearance: 0.40 mm (0.0157 in.) 2.
SST
D02673
INSTALL THE BEARING RACE (FOR THE OUTPUT SHAFT) Using SST and a press, install the bearing race. SST 09316-6001 1 (09316-00011, 09316-00031), 09950-60020 (09951-00890)
D02662
3.
SST
INSTALL THE BEARING RACE (FOR THE IDLER GEAR) Using SST and a press, install the bearing race. SST 09316-6001 1 (09316-00011, 09316-00031), 09950-60020 (09951-00790)
D02661
4. INSTALL OIL RECEIVER TO FRONT CASE Install the oil receiver and bolt. Torque: 12 Nm (120 kgfcm, 9 ftlbf)
D02672
INSTALL SHIFT OUTER LEVER AND INNER LEVER Install the shift inner lever, washer and outer lever to the front case. Using a pin punch, hammer and socket wrench, tap in the lever lock pin. Install the washer and nut to the shift outer lever. Torque: 12 Nm (120 kgfcm, 9 ftlbf)
Socket Wrench
2004 LAND CRUISER (RM1071U)
D04309
Author :
Date :
1901
TR-14
TRANSFER TRANSFER ASSEMBLY
6. (a) (b)
ASSEMBLE SHIFT FORK NO. 1 AND SHIFT FORK NO. 1 SHAFT Assemble the shift fork No. 1 and shift fork No. 1 shaft. Using a pin punch and hammer, drive in the slotted spring pin.
TF0857
7.
INSTALL IDLER GEAR ASSEMBLY WITH CENTER DIFFERENTIAL ASSEMBLY, SHIFT FORK NO. 1 AND SHIFT FORK NO. 1 SHAFT TO FRONT CASE NOTICE: Set the shift inner lever into the fork head part of the shift fork No. 1 securely. 8. INSTALL INPUT SHAFT ASSEMBLY 9. INSTALL 2 BEARING RACES TO REAR CASE
TF0986
FIPG
3 mm (0.12 in.)
10. (a)
(b)
ASSEMBLY FRONT CASE AND REAR CASE Apply FIPG to the front case. FIPG: Part No. 08826-00090, THREE BOND 1281 or equivalent Assemble the front case and rear case.
D02756
(c)
(d)
Apply liquid sealer to the A bolt threads. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent Install the 8 bolts. Torque: 37 Nm (380 kgfcm, 27 ftlbf)
D02864
11. ASSEMBLE FRONT CASE AND REAR CASE Using a snap ring expander, install the snap ring to the rear case.
D02669
Author :
Date :
1902
TR-15
TRANSFER TRANSFER ASSEMBLY
12. (a)
5 mm (0.20 in.)
(b)
FIPG
D02754
INSTALL CASE COVER Apply FIPG to the rear case. FIPG: Part No. 08826-00090, THREE BOND 1281 or equivalent Install the case cover.
(c)
(d)
Apply liquid sealer to the bolt threads. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent Install the 5 bolts. Torque: 37 Nm (380 kgfcm, 27 ftlbf)
D02863
13. INSTALL OIL STRAINER TO REAR CASE Install the oil strainer and 2 bolts. Torque: 4.9 Nm (50 kgfcm, 43 in.lbf)
D02667
SELECT ADJUSTING SHIM FOR IDLER GEAR REAR TAPER ROLLER BEARING Using vernier calipers, measure dimension A. Lightly hole down the bearing outer race in the thrust direction to eliminate any looseness before making the measurement.
Z18975
(c) (d)
Using a steel straight edge and feeler gauge, measure the clearance of dimension B. Calculate the required thickness of the adjusting shim. Thickness: Dimension A + Dimension B + [0.022 - 0.049 mm, (0.0009 - 0.0019 in.)]
Z18976
Author :
Date :
1903
TR-16
TRANSFER TRANSFER ASSEMBLY
(e)
From the following table, select a shim so that its thickness is within the range of the calculation.
Thickness mm (in.) 0.30 (0.0118) 0.45 (0.0177) 2.40 (0.0945) 2.60 (0.1024) 2.80 (0.1102) 3.00 (0.1181) Mark 8 9 10 11 12 13 Thickness mm (in.) 3.20 (0.1260) 3.40 (0.1339) 3.60 (0.1417) 3.80 (0.1496) 4.00 (0.1575) 0.55 (0.0216) 2 3 4 5 6 7
Mark
15.
C
(a) (b)
SELECT ADJUSTING SHIM FOR OUTPUT SHAFT TAPER ROLLER BEARING Using a steel straight edge and feeler gauge, measure the clearance of dimension C. Lightly hold down the bearing outer race in the thrust direction to eliminate any looseness before making the measurement.
TF1063
(c) (d)
F E D
TF1064
Using a steel straight edge and vernier calipers with depth gauge, measure dimension D. Dimension D is the straight edge thickness (Dimension F) subtracted from dimension E in the illustration to the left. Dimension D: Dimension E - Dimension F
(e)
F G H
(f)
(g)
TF1065
(h)
Using a steel straight edge and vernier calipers with depth gauge, measure dimension G. Dimension G is the straight edge thickness (Dimension F) subtracted from Dimension H. Dimension G: Dimension H - Dimension F Calculate the required thickness of the adjusting shim. Thickness: Dimension G - (Dimension D - Dimension C) + [0.014 0.039 mm, (0.0006 0.0015 in.)] From the following table, select a shim so that its thickness is within the range of the calculation.
Thickness mm (in.) 0.30 (0.0118) 0.45 (0.0177) 1.00 (0.0394) 1.20 (0.0472) 1.40 (0.0551) 1.60 (0.0630) Mark H J K L M N Thickness mm (in.) 1.80 (0.0709) 2.00 (0.0787) 2.20 (0.0866) 2.40 (0.0945) 2.60 (0.1024) 0.55 (0.0216) B C D E F G
Mark
Author :
Date :
1904
TR-17
TRANSFER TRANSFER ASSEMBLY
3 mm (0.12 in.)
16. (a)
INSTALL REAR EXTENSION HOUSING Apply FIPG to the rear extension housing. FIPG: Part No. 08826-00090, THREE BOND 1281 or equivalent
FIPG
D01995
Install the rear extension housing and 9 bolts. Torque: 37 Nm (380 kgfcm, 27 ftlbf) ASSEMBLE SHIFT FORK NO. 2 SHAFT AND SHIFT FORK NO. 2 Install the shift fork No. 2 to the shift fork No. 2 shaft. Install the 3 snap rings to the shift fork No. 2 shaft.
D02861
18.
INSTALL CLUTCH SLEEVE WITH SHIFT FORK NO. 2 SHAFT AND SHIFT FORK NO. 2
HINT: Make sure to install the clutch sleeve in the correct direction.
Front
Q00541
19. (a)
INSTALL FRONT EXTENSION HOUSING Apply FIPG to the front extension housing. FIPG: Part No. 08826-00090, THREE BOND 1281 or equivalent
D01991
(b)
Install the front extension housing and 6 bolts. Torque: 37 Nm (380 kgfcm, 27 ftlbf)
HINT: Set the clutch sleeve in differential lock condition. 20. INSTALL TRANSFER INDICATOR SWITCH Install the 3 transfer indicator switches with 3 new gaskets. Torque: 37 Nm (380 kgfcm, 27 ftlbf)
D02860
Author :
Date :
1905
TR-18
TRANSFER TRANSFER ASSEMBLY
(c)
Q07105
INSTALL BALL, SPRING AND SCREW Install the ball and spring. Apply liquid sealer to the screw plug threads. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent Using a torx socket wrench (T40), install the screw plug. Torque: 19 Nm (190 kgfcm, 14 ftlbf)
22. INSTALL OUTPUT GEAR TO FRONT CASE HINT: Apply gear oil to the output gear. NOTICE: Do not turn the output gear.
D02862
23. (a)
4 mm (0.16 in.)
INSTALL MOTOR ACTUATOR Apply FIPG to the motor actuator. FIPG: Part No. 08826-00090, THREE BOND 1281 or equivalent
FIPG
D02666
Q04610
(b)
Install the motor actuator and 4 bolts. Torque: 18 Nm (185 kgfcm, 13 ftlbf) 24. INSTALL SPEED SENSOR DRIVE GEAR Install the driven gear and bolt. Torque: 11 Nm (115 kgfcm, 8 ftlbf) 25. INSTALL BREATHER HOSE
D02690
Author :
Date :
1906
TR-1
TRANSFER TRANSFER SYSTEM
TRANSFER SYSTEM
TR064-02
PRECAUTION
When working with FIPG material, you must observe the following. S Using a razor blade and gasket scraper, remove all the old FIPG material from the gasket surfaces. S Thoroughly clean all components to remove all the loose material. S Clean both sealing surfaces with a non-residue solvent. S Apply FIPG in an approx. 1.2 mm (0.047 in.) wide bead along the sealing surface. S Parts must be assembled within 10 minutes of application. Otherwise, the FIPG material must be removed and reapplied.
Author :
Date :
1889
TR-3
TRANSFER TRANSFER UNIT
TRANSFER UNIT
TR066-02
COMPONENTS
Transfer Indicator Switch Connector (Low Switch) Transfer Indicator Switch Connector (Neutral Switch) Motor Actuator Connector
106 (1,080, 78) 106 (1,080, 78)
Breather Hose
69 (700, 51)
Transfer
69 (700, 51)
69 (700, 51)
28 (290, 21)
Crossmember
Author :
Date :
1891
TR-6
TRANSFER TRANSFER UNIT
TR068-02
INSTALLATION
Installation is in the reverse order of removal (See page TR-4 ). HINT: S Apply MP grease to the transfer adaptor oil seal. S After install, do the road test.
Author :
Date :
1894
TR-4
TRANSFER TRANSFER UNIT
TR067-02
REMOVAL
1. RAISE VEHICLE NOTICE: Make sure that the vehicle is securely supported.
2. REMOVE TRANSFER CASE PROTECTOR Remove the 3 bolts and transfer case protector. Torque: 28 Nm (290 kgfcm, 21 ftlbf)
D02645
Oil Level 0 - 5 mm
3.
4.
DRAIN TRANSFER OIL Oil grade: API GL-4 or GL-5 Viscosity: SAE 75 W-90 Capacity: 1.3 liters (1.4 US qts, 1.1 lmp. qts) Torque: 37 Nm (380 kgfcm, 27 ftlbf) REMOVE FRONT AND REAR PROPELLER SHAFTS (See page PR-4 )
Filler Plug
Drain Plug
D02646
5.
DISCONNECT TRANSFER SHIFT LEVER ROD ASSEMBLY Remove the clip, plate washer, wave washer and bushing, and disconnect the transfer shift lever rod assembly. 6. DISCONNECT GROUND CABLE Remove the bolt and disconnect the ground cable from the transfer.
D01618
Wooden Block
Q09803
7. REMOVE CROSSMEMBER (a) Support the transmission, as shown. NOTICE: Use a wooden block so not to damage the transmission oil pan. (b) Remove the 8 bolts, 2 nuts and crossmember. Torque: Bolt: 50 Nm (510 kgfcm, 37 ftlbf) Nut: 74 Nm (750 kgfcm, 54 ftlbf)
Author :
Date :
1892
TR-5
TRANSFER TRANSFER UNIT
Hose Clip
Pipe
Q09804
8. DISCONNECT BREATHER HOSE HINT: At the time of installation, assemble the clip to the position shown in the illustration. 9. DISCONNECT NO. 1 VEHICLE SPEED SENSOR, 3 TRANSFER INDICATOR SWITCH AND MOTOR ACTUATOR CONNECTORS 10. JACK UP TRANSFER SLIGHTLY Using a transmission jack, support the transfer. 11. (a) (b) (c) REMOVE TRANSFER FROM TRANSMISSION Disconnect the wire harness from the transfer. Remove the 6 transfer adaptor rear mounting bolts. Torque: 69 Nm (700 kgfcm, 51 ftlbf) Pull out the transfer down and toward the rear.
D02643
Author :
Date :
1893
TR-2
TRANSFER TROUBLESHOOTING
TROUBLESHOOTING
TR065-02
Noise
Oil leakage
Author :
Date :
1890
TR-47
TRANSFER TRANSFER SHIFT LEVER ASSEMBLY
COMPONENTS
Plate Washer Wave Washer Clip Transfer Shift Lever Rod Assembly Bushing
Wiring Harness Clamp Bracket Bushing S Gasket Transfer Shift Lever Boot
Transfer Control Shift Lever Retainer Wave Washer Plate Washer Snap Ring Transfer Shift Lever Boot S Gasket
F08168
Author :
Date :
1935