Professional Documents
Culture Documents
ABB Valve Series 14 PDF
ABB Valve Series 14 PDF
SERIES 14
Single Seated Globe Valve for Ratings ANSI 150-600
Features
General Designed to ensure it represents a cost effective solution to a variety of process control applications, the construction of this range of valve is of a simple form allowing rapid assembly and high interchangeability of trims. Performance: High flow capacity. Tight shut-off. Excellent flow control rangeability. Low weight. Streamline flow passages to improve capacity. Design Flexibility: Inherent Modified Equal Percentage trim, with options for equal percentage and linear from characterised positioner. Clamped guide and seat allows quick change for modification/service. High interchangeability of trim components and soft parts. Design Integrity: Optimised using computer aided analysis. Designed to ASME B16.34 High integrity precision cast components. Quality Manufacturing: Rigorously tested to ensure specified performance on site. Quality Assurance systems certified to ISO 9001 NACE MR-01-75 certification.
Temperature Range:
Actuation:
Multispring style Series H actuators, available in 55in2, 110in2 & 220in2 as standard.
Bonnet Packings:
Teflon Chevron for standard duty. Flexigraph for high temperatures.
Sizing/Noise:
The procedures for performing valve sizing, velocity and sound pressure level calculations are detailed in the Technical Sizing and Selection Manual.
Design Standards:
ASME B16.34 IEC 534.3-1
Design Cv Values
The design Cv values detailed below are defined as the flow of water (SG=1) through the valve at full lift in US gallons per minute with a pressure drop of 1psi.
Characteristics Available:
Inherent Modified Equal Percentage (Equal Percentage & Linear available with characterised positioner) Figure 2. High Friction Cage Trim illustrated with Balanced Plug
Plug Options:
Unbalanced Contoured Trim. Unbalanced Cage Guided (1 to 4 Valves) or Balanced Metal/Metal Cage Guided (1.1/2 to 4 valves) with Resilient or Graphite piston rings. Soft seats are available for bubble tight shut off.
Direction of Flow:
Recommended flow under for both liquids and gas of Contoured trims. Flow over the plug for liquids & flow under for gases of Cage Guided trims.
Severe Duty:
The High Friction (HF) trims are suitable for high pressure drop applications to prevent the onset of cavitation and reduce the noise levels generated as the result of both gas/vapour and liquid flows. Figure 3. High Friction HF trim illustrated with Solid Plug
Trim Cv Calculation
A full set of procedures for calculating the Cv with various fluids is detailed in the Sizing and Selection Manual. Please contact the nearest Sales Office for your copy.
Body Selection
The valve body must be capable of supporting the selected trim without producing excessive velocities. The following tables can be used as a guide for determining the maximum recommended body velocities for both liquid and gas/ vapour applications.
Liquid Service
The velocities detailed in Table 3. below reflect the normal inlet and outlet maximum velocities recommended to eliminate body erosion and prevent trim instability. Other factors may reduce the following figures further. Refer to Sizing and Selection Manual for further details. Table 3. Recommended maximum inlet and Outlet Velocities Liquid Service
Gas/Vapour Service
These velocities avoid problems of vibration and body erosion. Where noise levels are a consideration velocities should be restricted to the relevant Mach numbers. Table 4. Recommended maximum inlet and Outlet Velocities Gas/Vapour Service
Note:
(STD) or (SPL) refer to the amount of seat/plug lapping carried out at final assembly.
Note: 1.Face to face dimensions comply with IEC 534.3-1 2.ABB Control Valves reserve the right to confirm dimensions on certified drawings *For other Valve/Actuator combinations, please consult factory Table 8. Valve Dimensions
www.abb.com/controlvalves
The Companys policy is one of continuous product improvement and the right is reserved to modify the specifications contained herein without notice. Printed in UK (10.02) ABB 2002
Series14/03/03
ABB Control Valves UK Kent Introl Ltd Armytage Road, West Yorkshire England HD6 1QF Tel: +44 (0)1484 710311 Fax: +44 (0)1484 407407
ABB Control Valves - India Introl (India) Ltd H-34, MIDC, Ambad Nashik 422 010 India Tel: +91 253 381434 Fax: +91 253 384413
Issue 4