Professional Documents
Culture Documents
R1 Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#int s0/3/0 R1(config-if)#ip add 192.168.13.1 255.255.255.0 R1(config-if)#clock rate 64000 This command applies only to DCE interfaces R1(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to down R1(config-if)#exit R1(config)#int s0/3/1 R1(config-if)#ip add 192.168.12.1 255.255.255.0 R1(config-if)#clock rate 64000 This command applies only to DCE interfaces
R1(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/1, changed state to up R1(config-if)#exit R1(config)#int f0/0 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up R1(config-if)#ip add 192.168.1.1 255.255.255.0 R1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config-if)#exit R1(config)#router rip R1(config-router)#network 192.168.12.0 R1(config-router)#network 192.168.13.0 R1(config-router)#network 192.168.1.0 R1(config-router)#end
R3
Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R3 R3(config)#int s0/3/0 R3(config-if)#ip add 192.168.13.2 255.255.255.0 R3(config-if)#clock rate 64000 R3(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to up R3(config-if)#exit %LINK-5-CHANGED: Interface Serial0/3/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up R3(config)#int s0/3/1 R3(config-if)#ip add 192.168.2.1 255.255.255.0 R3(config-if)#clock rate 64000 R3(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/3/1, changed state to up R3(config-if)#exit %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up R3(config)#int f0/0 R3(config-if)#ip add 192.168.3.1 255.255.255.0 R3(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config-if)#exit R3(config)#router rip R3(config-router)#network 192.168.13.0 R3(config-router)#network 192.168.23.0 R3(config-router)#network 192.168.3.0 R3(config-router)#end R3# %SYS-5-CONFIG_I: Configured from console by console %SYS-5-CONFIG_I: Configured from console by console
R2
Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)#int s0/3/0 R2(config-if)#ip add 192.168.12.2 255.255.255.0 R2(config-if)#clock rate 64000 R2(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up R2(config-if)#exit R2(config)#int s0/3/1 R2(config-if)#ip add 192.168.23.2 255.255.255.0 R2(config-if)#clock rate 64000
This command applies only to DCE interfaces R2(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up R2(config-if)#exit R2(config)#int f0/0 R2(config-if)#ip add 192.168.2.1 255.255.255.0 R2(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R2(config-if)#exit R2(config)#router rip R2(config-router)#network 192.168.23.0 R2(config-router)#network 192.168.12.0 R2(config-router)#network 192.168.2.0 R2(config-router)#exit
R2
Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)#int s0/3/1 R2(config-if)#ip add 192.168.23.2 255.255.255.0 R2(config-if)#clock rate 64000 This command applies only to DCE interfaces Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up R2(config-if)#ip route 192.168.3.0 255.255.255.0 192.168.23.1 R2(config)#int s0/3/0
R2(config-if)#ip add 192.168.12.2 255.255.255.0 R2(config-if)#clock rate 64000 R2(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to up Router(config-if)#ip route 192.168.2 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up R2(config-if)#ip route 192.168.1.0 255.255.255.0 192.168.12.1 R2(config)#int f0/0 R2(config-if)#ip add 192.168.2.1 255.255.255.0 R2(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1
Router> Router>
Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#int s0/3/0 R1(config-if)#ip add 192.168.13.1 255.255.255.0 R1(config-if)#clock rate 64000 This command applies only to DCE interfaces R1(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to down Router(config-if)#ip route 192.168.3.0 255.255.255.0 192.168.13.2 %SYS-5-CONFIG_I: Configured from console by console R1(config)#int s0/3/1 R1(config-if)#ip add 192.168.12.1 255.255.255.0 R1(config-if)#clock rate 64000 This command applies only to DCE interfaces R1(config-if)#no shut %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up
%LINK-5-CHANGED: Interface Serial0/3/0, changed state to up Router(config-if)#ip route 192.168.2.0 255.255.255.0 192.168.12.2 R1(config)#int f0/0 R1(config-if)#ip add 192.168.1.1 255.255.255.0 R1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3
Router>ena Router#conf ter Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R3 R3(config)#int s0/3/0 R3(config-if)#ip add 192.168.13.2 255.255.255.0 R3(config-if)#clock rate 64000
Router(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up R3(config-if)#ip route 192.168.1.0 255.255.255.0 192.168.13.1 R3(config)#int s0/3/1 R3(config-if)#ip add 192.168.23.1 255.255.255.0 R3(config-if)#clock rate 64000 R3(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/3/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed state to up R3(config-if)#ip route 192.168.2.0 255.255.255.0 192.168.23.2 R3(config)#int f0/0 R3(config-if)#ip add 192.168.3.1 255.255.255.0 R3(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up