Question 2 of 25. Where must the required RT location markers be placed?
On the film holder/cassette.
On the part.
They can be scribed on the film after developing.
Location markers are optional unless required by the referencing code.
Mark for follow up
Question 3 of 25. After the penetrant dwell time, the maximum emulsification time shall be:
5 min
10 min
15 min
None of the above
Mark for follow up
Question 4 of 25. For a double wall exposure (DWE) / single wall viewing (SWV) RT Technique, a minimum of ______________exposures is required for complete coverage of circumferential welds.
1
2
3
4
Mark for follow up
Question 5 of 25. Typical four step and five step UT pulse-echo US Customary calibration blocks for thickness- measurement equipment have a thickness tolerance of _____________.
0.001mm
0.02mm
0.05 in
0.001 in
Mark for follow up
Question 6 of 25. __________________can be detected by the Radiographic examination method.
Surface discontinuities
Surface and near surface discontinuities
Subsurface discontinuities
Surface and subsurface discontinuities
Mark for follow up
Question 7 of 25. Which of the following is not included in ASME V?
Acoustic emission testing
Spark Testing (Positive Material Identification)
Ultrasonic examination
Visual examination
Mark for follow up
Question 8 of 25. When, during magnetic particle examination, non-magnetic coatings are applied to enhance contrast, it must be demonstrated that indications ______________________.
can be detected in 20 degrees F weather
cannot be detected through the coating
can be detected through the coating
None of the above
Mark for follow up
Question 9 of 25. One of the five magnetization techniques used in MT is _________.
Hall-effect Tangential-field
circular
round
shearwave
Mark for follow up
Question 10 of 25. A full penetration butt weld in a 1/4 inch thick plate with 1/8 inch thick reinforcement is to be radiographed with the IQI on the film side. The radiographer does not have any hole-type IQIs with a designation of 15. What other designated hole IQIs can be used instead?
Both 20 and 10
10
20
17
Mark for follow up
Question 11 of 25. A single film technique was used to make a radiograph using a Cobalt-60 source. The minimum permitted density in the area of interest is: ____________.
1.3
1.8
4.0
2.0
Mark for follow up
Question 12 of 25. What is the difference between an inspection and an examination per Section V of the ASME Code?
Inspection is performed by the authorized inspector (AI), whereas examination is performed by the manufacturers personnel.
Examination is performed on materials whereas inspection is performed on equipment.
Examination is performed by the authorized inspector (AI) whereas inspection is performed by the manufacturers personnel.
There is no difference between the two.
Mark for follow up
Question 13 of 25. A written procedure is required by ASME Section V for __________________.
MT and UT only
RT, UT, MT and PT
UT and MT only
RT and MT only
Mark for follow up
Question 14 of 25. When should PT developer be applied?
As soon as possible after penetrant removal. Not to exceed time in the written procedure.
7 minutes after cleaning
No longer than 4 hours after cleaning
As the job schedule permits
Mark for follow up
Question 15 of 25. Name one typical discontinuity readily detectable by the liquid penetrant method.
Heat Affected Zone (HAZ) surface cracks on a NPS 2 girth weld
Slag inclusions on a NPS 8 longitudinal weld
Incomplete fusion (I.F.) at the root of an NPS 2 girth weld
Incomplete Penetration (I.P.) on an Nominal Pipe Size (NPS) 2 girth weld
Mark for follow up
Question 16 of 25. A inch thick material is to be magnetic particle tested with a yoke. The following types of yoke are acceptable.
Shear wave yokes.
Both alternating current and direct current electromagnetic yokes.
Direct Current electromagnetic yokes.
Alternating current magnetic yokes.
Mark for follow up
Question 17 of 25. For visible magnetic particles, the minimum light intensity required during examination and evaluation is ________.
1000 Lx
10000 Lx
1000 microns W/cm2
100 Lx
Mark for follow up
Question 18 of 25. Geometric unsharpness is determined by:
Ug = f d / d
Ug = f t / d
Ug = P D / d
Ug = F d / D
Mark for follow up
Question 19 of 25. Which of the following is not considered a type of film blemish?
Light letter B on a darker background.
Fogging.
Scratches and finger marks.
Streaks and water marks.
Mark for follow up
Question 20 of 25. A 4T hole on an ASME SE-1025 number 20 IQI has a diameter of ____________ inches.
0.080
0.070
0.043
0.80
Mark for follow up
Question 21 of 25. __________________can be detected by the Magnetic particle testing method.
Surface and near surface discontinuities
Surface and subsurface discontinuities
Subsurface discontinuities
Surface discontinuities
Mark for follow up
Question 22 of 25. Certifications of contaminant content for all liquid penetrant materials used on all nickel base alloys, austenitic stainless steel and titanium shall include which of the following?
Penetrant Manufacturer's name
Batch Numbers and test results
Technician's name
Penetrant Manufacturer's name, Batch Numbers, and test results
Mark for follow up
Question 23 of 25. Which of the following discontinuities is typically detected by the magnetic particle method?
Interpass lack of fusion
Slag inclusions
Toe cracks
Lack of penetration
Mark for follow up
Question 24 of 25. Which of the following methods may be used to remove weld surface irregularities that may mask indications of unacceptable discontinuities when using RT?
Removal by grinding
Removal by machining
Removal by other methods
All of the above
Mark for follow up
Question 25 of 25. A pipe weld is to be radiographed using a double wall exposure (DWE) technique with double wall viewing (DWV). The IQI selection is based on___________.
the sum of the wall thicknesses
the single wall thickness plus any backing ring thickness