Professional Documents
Culture Documents
ADSS Specification PDF
ADSS Specification PDF
ACCESSORIES SPECIFICATIONS
Contents
ADSS cable is loose tube stranded. Fibers are positioned into a loose tube made of
high modulus plastics. The tubes are filled with a water-resistant filling compound. The
tubes (and fillers) are stranded around FRP (Fiber Reinforced Plastic) as a non-metallic
central strength member into a compact and circular cable core. After the cable core is
filled with filling compound, it is covered with a thin polyethylene (PE) inner sheath. After
two layers of Aramid yarns are applied in two directions over the inner sheath as strength
member, the cable is completed with PE or AT (anti-tacking) outer sheath.
Characteristic
z
z
z
z
z
z
z
Application
The actual status of overhead power lines is taken into full consideration when ADSS
cable is being designed. For overhead power lines under 110KV, PE outer sheath is
applied. For power lines equal to or over 110KV, AT outer sheath is applied. The dedicate
design of Aramid quantity and stranding process can satisfy the demand on various spans.
Cable Code
ADSSXXX(KN)X--X
Fiber type
Fiber count
Maximum allowable working tension
Sheath material
All Dielectric Self-supporting Aerial cable
Climate Type
A
B
C
D
Wind speed(m/s)
25
35
10
10
Ice(mm)
0
0
5
10
Extra load(N/m)
0.7
0.7
2.5
4.4
Single-layer Heliformed
Tension set
Dead-end Rods
Casing Ring
Anchor Shackle
Extension Link
Double-layer
Heliformed Tension Set
Clevis Thimble
Anchor Shackle
Dead-end Rods
Armor Rods
General information:
Tension Sets are intended for connecting ADSS cable and poles. Aluminium claded
Steel wires can protect and provide cushioning to the ADSS cable. The special design of
heliformed rods makes ensure that Tension Sets can not cause undue stress to the ADSS
cable. As a result, the normal lifetime of cable system is ensured.
Structure and Material:
Tension Set Outer-layer--- Stainless steel pressing.
Anchor Shackle--Hot dipped galvanized steel Anchor Shackle is connected with
Reinforcing Pole units. Tensile Strength: U-7: 69kN, U-10:98kN, U-12:118kN, U-16:157kN.
Plastic Inner---- It is made of anti-aging, anti-ultraviolet and corrosion-resisting
plastic.
Dead-end Rods--Rods are factory assembled into one subset with a layer of firm emery
inside, in order to increase gripping power of Tension Sets while decreasing side pressure.
Sets are color marked to reduce misalignment errors and to speed installation.
Casing Ring----- It is extended of stainless steel plugging in shackle of Strain Clamp
for protection.
Extension Link: Hot dipped galvanized steel Extension Link is intended for
connecting Anchor Shackle and Clevis Thimble and avoiding Strain Clamp exit close to
poles. It is sure that the cable has enough winding radius. Tensile Strength: 40kN, 70kN,
7
General information:
The Suspension Sets are designed to reduce static stress at the support point of
ADSS cable, as well as ensure that the cable is cushioned against the dynamic stress of
aeolian vibration. The combination of the HSU and Armor Rods provides protection
against cable bending stress, there is no other stress concentration, so that the fiber optic
doesnt produce extra loss in the cable.
Structure and Material:
Housing------It is made of cast aluminium alloy, which is stable, better anticorrosive in
areo and mechanical performance.
Rubber Insert------It consists of high-class rubber, compounded for resistance to
ozone, wheathering extreme high and low temperature variations and compression set.
Bolt, Nut, Split Washer, Lock Pin------Hot dipped galvanized.
Closed Washer------Electric power standards
Anchor Shackle------Electric power standards
8
Armor Rods ------High strength aluminium alloy for wheathering extreme high and
low temperature variations, compression set, water resistance and high hardness.
HSU Rods------the same to Armor Rods
4. Vibration Damper
Gripping Section
Damping Section
Standards:
Catalog
Number
Cable Dia.
(mm)
Length of Gripping
Section(mm)
Total Length
(mm)
Net Weight
(kg)
Color
8.30-11.70
250
1300
0.28
Yellow
11.71-14.30
250
1350
0.30
Green
14.31-19.30
330
1670
0.66
Blue
Metal Splice Closure is designed for splicing ADSS Cables, the normal cables and the
connection between ADSS Cable and the normal cable, including two to four sleeves for
input and output continuing. The sleeve quantity is decided on the requirement. The
special design of stainless band, fixed unit and strengthening core makes cable more
steady, cable storage wider to speed storing and cable bending radius enough big,
avoiding fiber optic extra loss and ensuring transmission performance. The double sealed
designs make Splice Closure more reliable, easy to install and fix.
9