Professional Documents
Culture Documents
Materials Engineer
Materials Engineer
20. Which of the following percent air voids is most preferable in bituminous mixture
a. 0%
b. 5%
c. 8%
21. a) Viscocity b) solubility c) Flash point d) Extraction test determines the bitumen content of asphalt
cement
22. a) Distillation b) Penetration c) Viscocity d) Ductility is the consistency test on solid asphalt.
23. a) Tack coat b) Prime coat c) Seal coat is the bituminous coating applied to an old concrete
pavement to be used as base.
24. A Job-mix formula provides for close control of
a. asphalt content
b. aggregate gradation
c. both a and b
25. a) Flexibility b) Durability c) Stability d) Workability is the resistance of an asphalt pavement
against weathering.
26. The temperature of hot mixes being delivered should not be less than its
a. mixing
b. application
c. heating
d. compaction temperature
27. A Bituminous Seal Coat is usually applied with aggregate
a. true
b. false
c. it depends on the surface application
28. The maximum specific gravity of an asphalt mix containing 6.0% asphalt by weight of mix is 2.6.
If the specific gravity of an asphalt is 1.01, the specific gravity of the aggregate is equal to
a. 2.65
b. 2.56
c. 2.76
d. 2.70
29. The weight in air of a core specimen taken from asphalt pavement is 4,128 g. If its SSD weight is
4,137 g. and its weight in water is 2,237 g. Therefore, its bulk density is
a. 2.42
b. 1.72
c. 2.28
d. 2.69
30. The bulk specific gravity of a sample of bituminous pavement taken from a newly rolled section is
2.244. If the laboratory compacted specific gravity is 2.362 and the minimum compaction
requirement is 95%, the pavement is
a. satisfactorily rolled
b. over compacted
c. in need of more rolling
c. 15 min, after the cement is added into the aggregates and water.
41. The fineness modulus is highest for
a. coarse
b. very coarse
c. fine
d. very fine, sand.
42. In molding concrete cylinder specimen, each layer should be rodded
a. 25
b. 56
c. 60
d. 100 times.
43. Concrete cylinder sample should be molded in
a. 1
b. 2
c. 3
d. 4 equal layers.
44. Maintaining the water-cement ratio, the concrete containing
a. 50.0 mm
b. 37.5 mm
c. 19.0 mm
d. 12.5 mm maximum size aggregate will develop the highest strength.
45. Paving concrete will need less
a. sand
b. water
c. coarse aggregate
d. both a & b, than that of structural concrete.
46. The maximum percentage of abrasion loss allowed for concrete coarse aggregate is
a. 40
b. 45
c. 50
47. For Bituminous Concrete Surface Course, if asphalt cement is used, the percentage based on the
weight of aggregate should be
a. 3 to 5%
b. 5 to 8%
c. 6 to 10%
48. An aggregate base course of 21,600 m3 will require
a. 14
b. 15
c. 72 quality tests.
49. Coarse aggregate for Crushed Stone Aggregate Surface Course should have not less than
a. 40
b. 45
c. 50
d. 60 with at least one fractured face
50. Crushed Gravel Base Course, Grading C, shall be compacted in layers of not more than
a. 10 cm
b. 15 cm
c. 20 cm loose thickness.
51. An embankment to be constructed to a height of 65 cm will have a minimum of
a. 4
b. 5
c. 6 layers.
52. To give Bituminous Plant Mix Base Course greater to resistance to water
a. to 1%
b. 1 to 2%
c. 2 3% hydrated lime should be added during mixing.
53. The type of Bituminous Macadam Pavement is
a. asphalt cement
b. asphalt emulsion
c. rock asphalt
d. either a or b.
54. Prestressed Concrete Structures use concrete class
a. A
b. B
c. C
d. D
55. a) 5 b) 9 c) 3 pipes should be taken as sample to represent 225 reinforced concrete pipes.
56. Before placing the asphalt pavement, the gravel base course should be
a. seal coated
b. tack coated
c. prime coated
57. Concrete used in reinforced concrete culvert pipe should generally have a compressive strength of a
a. 16.54 Mpa ( 2400)
b. 27.56 Mpa ( 4000)
c. 20.67 Mpa ( 3000)
d. 34.45 Mpa ( 5000)
58. Concrete railings, pipes, and piles require the use of what class of concrete?
a. A
b. B
c. C
d. D
59. Steel bars for concrete reinforcement is tested for its
a. tensile
b. compression
c. bending
d. both a and c for properties.
60. Aggregate Base Course with a volume of 112,000m3 will have a minimum number of
a. 74
b. 75
c. 56
d. 374 quality tests.
61. Which plasticity index is most suitable for aggregate base course?
a. 5
b. 10
c. 15
d. 50 The fraction passing the 0.425 mm (No.40) shall have a liquid limit not greater than 25 and
plasticity index not greater than 6.
62. The specified flexural strength for paving concrete is
a. 350
b. 400
c. 525
d. 300
63. The sample of 12.5 mm diameter steel bar to be submitted for test should be at least
a. 20 cm
b. 40 cm
c. 100 cm
d. none of the above
64. a) Third point loading b) Three-edge bearing test c) Mid-span loading d) none of the above
method used in determining the strength of concrete pipes.
65 Prestressed concrete requires the use of Class
a. A
b. B
c. C
d. D concrete
66. If an asphalt pavement will be constructed over an old existing concrete pavement
a. prime coat
b. tack coat
c. seal coat
d. mortar coat
should be applied to the concrete pavement.
67. For bituminous concrete mixes, the asphalt material may either be asphalt cement or asphalt
emulsion
a. true
b. false
68. Coarse Aggregate for Bituminous Macadam Pavement should be
a. crushed gravel or stone
b. natural gravel
c. both a and b
d. none of the above
69/70. Tests for coarse aggregate include
a. abrasion
b. mortar strength
is the
c. absorption
d. all of the preceding
71/72. Tests for fine aggregate for concrete include
a. gradation
b. mortar strength
c. abrasion
d. all of the preceding
73. Unless otherwise specified in the special provision, the type of portland cement used in paving
concrete shall be
a. Type I
b. Type II
c. Type III
d. Type IV
74. During construction of a road project, if all the materials to be used are tested for quality, inspection
is no longer required
a. true
b. false
75. The degree of compaction of an embankment in our present Specifications is based on
a. CBR method
b. Unconfined compression test
c. AASHTO Designation T-180
d. Bulk Specific Gravity
76/77. Under Excavation for Structure, Item 106, the backfilling operation shall be done in 20 cm loose
layer and compacted to at least 95 Percent.
78. Soils are natural aggregates of minerals connected by strong and permanent cohesive forces
a. true
b. false
79. The boundary between sand and gravel is
a. 0.425 mm (#40)
b. 4.750 mm (#4)
c. 2.00 mm (#10)
d. 0.075 mm (#200)
80. A a) sandy clay b) clayey sand c) sand clay d) none of the preceding is a soil which exhibits the
properties of a clay but contains an appreciable amount of sand.
81. Plasticity test is done on soils passing
a. 0.425 mm (#40)
b. 2.00 mm (#10)
c. 0.075 mm (#200) sieve.
82. a) Soil compaction b) mechanical analysis c) In-place unit weight d) CBR is the process whereby
soil particles are contained more closely together through a reduction in the air voids, generally by
mechanical means.
83. Soils containing more than 35% passing 0.075mm (#200) sieve are classified under
a. silt-clay materials
b. granular materials
b. viscometer
c. penetrometer
d. pycnometer
96. a) Solid b) liquid c) Blown d) hot asphalt is preferable for bituminous prime coat.
97. a) Distillation b) Extraction c) Penetration d) Solubility is the test used in determining amount of
asphalt cement in a liquid asphalt.
98. a) Asphalt cement b) cut-back asphalt c) asphalt mixes d) asphalt emulsion are usually tested for
extraction.
99. Extraction test is the procedure used for separating
a. the asphalt from water in emulsified asphalt
b. asphalt from mineral aggregates
c. asphalt from kerosene solvent
d. asphalt from gasoline solvent
100. The optimum asphalt content obtained in a Marshall Stability test is the average of the asphalt content
of the Maximum Stability, Maximum density and
a. Maximum flow
b. Maximum air voids
c. 4% air voids
d. 4% flow
101. a) VMA b) Air voids c) Permeable voids are intergranular void spaces between aggregate particles.
102. The main difference between a bulk measured specific gravity of a bituminous mixtures and its
maximum measured specific gravity is the
a. weight of the voids
b. weight of the asphalt
c. volume of the voids
d. volume of the aggregates
103. a) Asphalt cement b) emulsified asphalt c) Rapid curing d) medium curing cut-back is the
best type of asphalt to be used for hot mixes.
104. A bituminous coating applied in an existing road prior to laying of a bituminous surface overlay is
a. prime coat
b tack coat
d. seal coat
105. The distance traveled by a standard penetration needle on a prepared sample of asphalt under
conditions for normal penetration is 8.6 mm. The material is
a. 40 50
b. 85 100
c. 120 150
d. 200 300 penetration grade
106. The maximum specific gravity of an asphalt mix containing 6.0% asphalt by weight of mix is 2.5.
if the specific gravity of the asphalt is 1.01, the specific gravity of the aggregate is equal to
a. 2.65
b. 2.56
c. 2.76
d. 2.70
The most important single factor which affects the quality of concrete is
cement content
aggregate gradation
water-cement ratio
aggregate quality
112.
a.
b.
c.
d.
113.
a.
b.
c.
d.
60
61
62
63
114.
a.
b.
c.
d.
115.
a.
b.
c.
d.
116.
a.
b.
c.
d.
117.
a.
b.
c.
d.
118.
a.
b.
c.
d.
119.
a.
b.
c.
d.
120.
The two (2) major components of concrete are
a. paste and mineral aggregates
b. cement and water
c. water and coarse aggregates
121.
The coarser the fine aggregate, the higher the fineness modulus
a. yes
b. no
c. depends on grading test
122.
The more the concrete is exposed, the greater the range of movement is
a. true
b. false
c. it depends upon the type of cement
123.
The samples of RSB to be submitted for test should be at least
a. 20 cm
b. 40 cm
c. 100 cm
124.
The efficient compaction, the embankment material should at the time of rolling be
a. dry
b. wet
c. at optimum moisture content
125. a) 15,000 kg b) 10,000 kg c) 5,000kg of 12.5mm diameter steel bar for concrete reinforcement is
the maximum quantity that a sample can represent.
126
127. Uncrushed aggregates are preferable than crushed aggregates for bituminous mixtures
a. true
b. false
c. it depends on the type of bituminous material.
128. The apparatus used in determining the consistency of liquid asphalt is the
a. flowmeter
b. viscometer
c. penetrometer
d. pycnometer
129. a) Solid b) liquid c) blown d) hot asphalt is preferable for bituminous prime coat.
130. a) Distillation b) Extraction c) Penetration d) solubility is the test used in determining the amount of
asphalt cement in a liquid asphalt.
131
. a) Asphalt cement b) Emulsified asphalt c) rapid curing cut-back d) medium curing cutback is the best type of asphalt to be used for hot mixes.
137. The field density of a bituminous pavement shall not be less than
a. 92 %
b. 95 %
c. 98 % of the specific gravity of the laboratory compacted specimen.
138. For ITEM 311 PCC pavement, coarse aggregate shall have a mass percent of wear not exceding
a. 50 %
b. 40 %
c. 45 %
d. 60 % when tested by AASHTO T- 96.
b. 95
c. 90 percent of the maximum dry density determined in accordance with AASHTO T-180,
Method D has been attained.
148. The maximum percentage wear allowed for Aggregate Subbase Course in a coarse portion retained
on a 2.00mm (No. 10) sieve is
a. 45
b. 50
c. 40
d. 55 percent by Los Angeles Abrasion Test determined by AASHTO T-96.
149. In manufacture of culvert pipes, the class of concrete used is
a. Class C
b. Class B
c. Class A
d. Class P
150. For Bituminous Concrete Surface Course, if Asphalt cement is used, the percentage based on the
weight of aggregate should be
a. 3 to 5 %
b. 5 to 8 %
c. 6 to 10 %
d. 4.5 to 8 %
151. Coarse aggregate for Crushed stone Aggregate Surface Course should have a mass percent of not
more than
a. 40 %
b. 45 %
c. 60 %
d. 50 % of the particle retained on the 4.75mm (No.4) sieve and shall have at least one (1)
fractured face.
152. Before placing the asphalt pavement, the gravel base course should be
a. seal coated
b. tack coated
c. prime coated
153. Prestressed Concrete structures uses concrete of class
a. A
b. B
c. C
d. P
154. An aggregate base course of 21,600m3 will require
a. 14
b. 25
c. 72
?
d. 40
155. An embankment to be constructed to a height of 600mm will have a minimum number of
a. 4
b. 5
c. 3
d. 6 layers.
156. Aggregate base course with a volume of 112,000 m3 will have a minimum number of
a. 74
b. 75
c. 56
d. 62 quality tests.
157. A portland cement concrete pavement, 6.5m wide and 23 cm. thick will be constructed for a total
paved area of 165,000 m3. Angular coarse aggregate will be used. If pavement will be opened to
traffic 14 days.
a. how many bags of cement will be required for Class A concrete?
b. How many quality tests are required for the cement?
c. How many quality and grading tests each are required for the coarse and fine aggregates?
d. How many sets of concrete beam samples will be required?
Vconcrete = 165000 x 0.23 = 37,950 m3
a. cement = 37950 x 9.1 = 345,345 bags
b QT of cement = 345,345/2000 = 173
c. VFA = 37950 x 0.54 = 20493 ; QFA = 20493/1500 = 14 ; GFA = 20493/75 = 274
VCA = 37950 x .68 = 25,886 ; QCA = 25806/1500 = 18 ; GCA = 25806/75 = 345
d. 37950/75 = 506 sets
158. Per our present Specifications for Highways and Bridges, including amendments, it is mandatiry to
open PCCP to traffic not later than
a. 14 days after pouring
b. 21 days after pouring
c. 7 days after pouring
d. 28 days after pouring
159. For 850 m3 of concrete paved in one day
a. 3
b. 2
c. 1 sets of concrete beam samples should be taken and tested for strength (thickness of pavement
= 0.23 m).
160. For 4050 m3 concrete coarse aggregate
a. 6
b. 5
c. 3
d. 4 samples should be submitted for quality tests.
161. The coarse aggregate of Item 201, Aggregate Base Course shall have a percentage of wear of not
more than
a. 40 %
b. 45 %
c. 50 %
d. 60 % as determined by Los Angeles Rattler Test.
162. The rate of application of emulsified asphalt used as bituminous prime coat is
a. 0.5 to 1.0 liter
b. 1.0 to 1.5 liter
c. 1.5 to 2.0 liter per square meter.
b. Item 307
c. Item 308
d. Item 310
173. ---------- is the result of asphalt layer instability or granular base or subgrade weakness. The
pavement usually twist out of shape.
a. disintegration
b. upheaval
c. distortion
d. bleeding
174. ---------- the localized upward displacement if a pavement due to swelling of the subgrade or some
portion of the pavement structure.
a. upheaval
b. edge cracking
c. raveling
d. depression
175
Item ---------- consist of furnishing and placing one or more courses of graded aggregates
and one or more application of bituminous material followed by a seal coat with cover aggregates
constructed in a prepare base is:
a. 303
b. 304
c. 305
d. 306
176.
a.
b.
c.
d.
177.
a.
b.
c.
d.
178.
a.
b.
c.
d.
179.
a.
b.
c.
d.
An asphalt cement submitted in the laboratory for quality test should always have a
corresponding
Job mix formula
Test report
Sample card
Minimum testing requirements
If an asphalt pavement will be constructed over an old existing concrete pavement, ---------should be applied to the pavement.
tack coat
prime coat
seal coat
mortar coat
The amount of emulsified asphalt to be added in a Bituminous Plant-Mix Surface Course, Cold
Laid (Item 308) shall be ------------ mass percent, total dry aggregate basis:
4 to 8
5 to 10
NOTE: If MC is used the proportion of bituminous material on the basis of
6 to 10
total dry aggregate shall be from 4.5 to 7.0 %.
7 to 12
------------ test is measure by the distance to which it will elongate before breaking when two (2)
ends of a briquet with specimen are pulled apart at a specified speed and temperature.
penetration
solubility
ductility
viscosity
b. asphalt cement
c. emulsified asphalt
d. blown asphalt
181.
a.
b.
c.
d.
182.
a.
b.
c.
d.
183.
a.
b.
c.
d.
The softness and hardness of an asphaltic material can be determined by -------- test.
softening point
loss on heating
penetration
distillation
184. The temperature of bituminous hot mix delivered in the project site should not be less than its ------temperature.
a. mixing
b. compaction
c. molding
d. spreading
184.
a.
b.
c.
d.
185.
a.
b.
c.
d.
186.
a.
b.
c.
d.
187.
a.
b.
c.
d.
188.
a.
b.
c.
d.
------------- test indicates the temperature in which an asphalt cement may be heated without the
danger of catching fire. It is used as criterion in eliminating fire hazards.
softening point
flash point
laser point
heating point
189.
a.
b.
c.
d.
190.
a.
b.
c.
d.
191.
a.
b.
c.
d.
The thinnest and most fluid grade of medium curing cutback asphalt is:
MC 800
MC 250
MC 70
NOTE: For MC, the higher the grade the thicker
MC 30
192.
a.
b.
c.
d.
193.
a.
b.
c.
d.
194.
a.
b.
c.
d.
The type of asphaltic material that is usually classified by its viscosity is:
liquid asphalt
blown asphalt
rock asphalt
lake asphalt
195.
a.
b.
c.
d.
Item 310, Bituminous Surface Course, Hot Laid provides an air voids between:
35%
57%
58%
8 10 %
196. Emulsified asphalt that has a positive charge particle is usually classified:
a. anionic
b. cationic
c. pozzolanic
d. ultrasonic
197.
a.
b.
c.
d.
198.
a.
b.
c.
d.
The coarse aggregates used in bituminous mix are those retained at sieve No.
8
10
30
200
199.
a.
b.
c.
d.
---------- test compares the compressive strength of dry and wet specimen of bituminous mix
marshall stability
immersion-compression
extraction
bulk specific gravity
200.
In item 310, bituminous Surface Course, Hot laid requires 70% minimum index of retained
strength (IRS). In the immersion-compression test, the dry stability is about 900 psi. Based on
the data, the wet stability should be at least ------- psi
a. 270
b. 630
Wet stability
c. 1286
NOTE: IRS = ----------------- X 100
d. 1500
Dry stability
201.
a.
b.
c.
d.
A compacted bituminous pavement shall have a minimum density of equal to or greater than -85 %
90 %
NOTE: The compacted pavement shall have a density equal to, or greater than 95
95 %
mass percent of the density of a laboratory specimen.
100 %
202.
a.
b.
c.
d.
The rate of application of emulsified asphalt used as tack coat, should be within the range of
0.2 0.5 liter/ m2
0.2 0.7
NOTE: The rate of application of either the Rapid Curing or the
0.15 0.7
Emulsified asphalt shall be within the range of 0.2 to 0.7
1.0 2.0
liter/m2, the exact rate as determined by the Engineer.
203.
a.
b.
c.
d.
The type of asphaltic material that is being referred to by penetration grade is:
emulsified asphalt
cutback asphalt
asphalt cement
mastic asphalt
204.
The optimum asphalt content obtained in a marshall stability test is the average of the asphalt
content of maximum stability, maximum density and
minimum flow index
maximum VMA
4 % or designed air voids
maximum VFA
a.
b.
c.
d.
205.
a.
b.
c.
d.
206.
In bituminous mixture, aggregates account for 92 % to 95 % of the weight of the mixture, while
asphalt ( the binder of the aggregates ) accounts for --------------35%
58%
NOTE: The proportion of bituminous material on the basis of total
5 10 %
dry aggregate, shall be from 5.0 to 8.0 mass percent.
7 10 %
a.
b.
c.
d.
207.
a.
b.
c.
d.
208.
a.
b.
c.
d.
209.
a.
b.
c.
d.
210.
a.
b.
c.
d.
211.
a.
b.
c.
d.
In asphalt pavement, prior to acceptance, a sample of full depth, 150mm x 150mm or 100mm
diameter shall be taken by a saw or core drill for -------- test
thickness determination
density
stability
a and b
In an asphalt pavement construction, after spreading bituminous mix, compaction will follow
where rolling shall begin at the sides and proceed longitudinally parallel toward the road
centerline, each trip overlapping ------- of the roller width, gradually progressing to the crown of
the road
1
1
2.0
The control of temperature during the mixing and compaction is of great significance in the ---of the resulting pavement
strength
skid resistance
flexibility
all of the above
based on the minimum testing requirements for Item 309, Bituminous Plant Mix, General, one
quality test for asphaltic material requires for every ------ tonnes or fraction thereof.
40
50
60
70
The test in emulsified asphalt which determines the resistance of the emulsion to break when
mixed with mineral aggregates
solubility
sieve test
cement mixing
storage stability
212.
a.
b.
c.
d.
What Item in the DPWH standards and specification is Bituminous Tack Coat?
301
302
303
304
213.
In identifying project location intended for asphalt pavement, which of the following criteria is
not appropriate to recommend?
drainage facilities is well-maintained
location is not a typhoon belt area
existing base course is stable
flood-prone section
a.
b.
c.
d.
214.
a.
b.
c.
d.
215.
Which of the following bituminous material is best recommended for sealing weakened plane
and construction joints of the PCCP.
asphalt cement
emulsified asphalt
cutback asphalt
joint filler asphalt
a.
b.
c.
d.
216.
a.
b.
c.
d.
217.
a.
b.
c.
d.
218.
a.
b.
c.
d.
The primary quality control mechanism for the production of asphalt mixtures which will have a
high degree of uniformity that will satisfy job requirements is called:
marshall stability test
job mix formula
immersion compression stability test
a and b
When a completed asphalt pavement exhibits too much voids, it is usually caused by the
following except of:
rolling the mixture below the temperature requirements
too much coarse aggregates
too little binder
too much fine aggregates
Test results from specimen taken from a recently rolled asphalt pavement showed that its total
asphalt content is 5.45 % by weight of mix. If the asphalt absorbed by the aggregate is 0.95 %,
the effective asphalt content by weight of mix is:
4.8 %
Pba
4.552 %
NOTE: Pbe = ----- x Ps
5.10 %
100
5.50 %
a.
b.
c.
d.
220.
a.
b.
c.
d.
FA, and MF are 2.50, 2.65 and 2.50, respectively, the overall specific gravity of composite
aggregates is:
2.58
30 + 50
+ 20
2.45
SG oa = --------------------------------2.66
30/2.5 + 50/2.65 + 20/2.5
2.77
If 95 % of the aggregates in question no. 45 is mixed with 5 % asphalt by weight of mix, the
specific gravity of the mix (if it is voidless) is: specific gravity of asphalt is 1.01.
2.45
2.23
100
2.39
Gmm = Gmb = ------------------------2.18
( voidless)
95/2.58 + 5/1.01
221.
If the bituminous mix in No.46 has a 5 % air voids, the bulk specific gravity (Gmb) can be
computed as:
a. 2.51
Gmm - Gmb
b. 2.27
% Air Voids = ----------------- x 100
c. 2.39
Gmm
d. 2.41
2.39 - Gmb
5/100 = -----------------2.39
222.
a.
b.
c.
d.
If the dry stability of a bituminous mix is 3,950 lbs. And its wet stability is 2,830 lbs., the Index
of Retained Strength (IRS) is:
50.20 %
71.60 %
Wet Stability
73.20 %
IRS = ----------------- x 100
61.10 %
Dry Stability
223.
a.
b.
c.
d.
224.
The distance travelled by a standard penetration needle on a prepared sample of asphalt cement
under condition for normal penetration is 9.0 mm ( the penetration scale has 1/10 mm
calibration). Asphalt cement is classified as --------- penetration grade.
60 70
85 100
120 150
200 - 300
a.
b.
c.
d.